Anti-vandal and security pushbutton switches

Anti-vandal and security pushbutton switches Distinctive features Attractive, robust and durable UG1410-A-R1 Irremovable Anti-jamming construction : reduced travel to prevent insertion of foreign parts Contact and mechanism protected against crushing Fire resistant Long life Different bushing sizes and actuator shapes Sealed versions Degree of protection of sealed versions (switches mounted on vertical panels) : IP65 to IP67 or IP69K depending on models UL/CSA approved models The AV series is a large range of very robust pushbutton switches, consisting of 2 families : ANTI-VANDAL PUSHBUTTON SWITCHES (pages 77-79) Great robustness (impact resistance IK08 (Ø 19 mm) and IK10 (Ø 22 mm) Actuator and bushing : stainless steel Bushing Ø 19 mm (.748) or 22 mm (.866 SECURITY PUSHBUTTON SWITCHES (pages 80-106) Large variety of models Actuator and bushing : nickel plated, chrome plated or polished varnished brass, stainless steel Bushing diameter 16 mm (.629), 19 mm (.748), 22 mm (.866) or 24 mm (.944) Marking, illumination, tactile feedback Numerous electrical functions (momentary or maintained) EXAMPLES OF MOUNTING FOR SEALED VERSIONS Gasket Preferred For thin panels With boot U2187 (sect. H) Dimensions : first dimensions are in mm while inches are shown as bracketed numbers. CAVET-A Packaging unit : specified on the following pages. Mounting accessories : Standard and special hardware are presented in section I. Sealing boots are available for models with Ø 19 mm (.748) bushing. See Section H. The company reserves the right to change specifications without notice. -76 www.apem.com

Anti-vandal pushbutton switches Distinctive features and specifications Very robust Impact resistance IK08 for model Ø 19 mm (.748) and IK10 for model Ø 22 mm (.866) Stainless steel actuator and bushing UL-CSA approved (long case only) SPECIFICATIONS Max. current/voltage rating with resistive load : - A contacts : 4A 12VDC, 500.000 cycles - C contacts : 2A 48 VDC, 10.000 cycles Initial contact resistance : 10 mω max. Insulation resistance : 1.000 MΩ min. at 500VDC Dielectric strength : 0 Vrms 50 Hz min. between terminals and frame 0 Vrms 50 Hz min. between terminals Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 11 mm (.433) max. Operating temperature : -30 C to +70 C Low level or mechanical life : 1.000.000 cycles Hand soldering : 300 C, 3 sec. max. Packaging unit : 20 pieces (models Ø 22) or 40 pieces (models Ø 19) MATERIALS Case : PBT Contacts : silver (A) or brass, silver plated (C) Bushing : stainless steel Actuator : stainless steel CUT-OUT Panel cut-out : Ø 19,2 mm (.755) or Ø 22,2 mm (.874) Min. pitch for matrix mounting : 30 mm x 30 mm (1.181x1.181) Degree of protection according to EN 62262, June 95 (NFC 20-015) ROBUSTNESS SEALING ( OPTION T ) Model Ø 19 mm (.748) Model Ø 22 mm (.866) 1.7 1.7 Kg Kg 29.5 29.5 cm cm Hammer radius 25 mm IK08 Striking energy: 5 joules (5Nm) 5 Kg 5 Kg 40 40 cm cm Hammer radius 50 mm IK10 Striking energy: 20 joules (20Nm) 2 1 Increased impact resistance provided by a nut or mechanical stop. Front panel sealing (IP65) CAVETKK-A ➀ internal gasket ➁ external gasket Option N does not include ➀ nor ➁. www.apem.com -77

Anti-vandal pushbutton switches Ø 19 mm (.748) Momentary () AV 3 40 (function 3) SERIES Actuator type 09 Flat 19 Curved 9D Flush Case 000 Long 100 Short Function 3 Contacts A Silver C Brass, silver pl. Terminals 9 Screw 2 Quickconnect Bush./act. material 40 Stainless steel Sealing N No T Sealed In the following model numbers, replace with elements selected in the above order format. Flat actuator - short case - 48VDC - AV09100 Hex nut 22 (.866) across flats ø19.00x1.00 SI (.748DIAx1.00 IS) 5.00 (.196) 7.30 (.287) 2.80 (.110) AV091003 940 Solder lug / quick-connect term. AV091003 240 ø2 ø15.00 ø2 2.80x0.5 (.110x.019) 1.20 (.047) for wires 1,5 mm 2 max. 9.50 6.50 3.00 (.374) (.255) (.118) EPOXY Flat actuator - long case - 4A 250VAC/8A125VAC - UL/CSA - AV09000 Hex nut 22 (.866) across flats Ø19.00x1.00 SI (.748DIAx1.00 IS) 5.00 (.196) AV090003A940 Ø2 Ø2 To order switches marked UL-CSA, add UU at the end of model number. for wires 1,5 mm 2 max. 11.60 (.456) 6.50 7.20 (.255) (.283) Curved actuator - AV19 Flush model - AV9D CAV09NUL 3.60 (.141) Ø2 Ø2 Ø2 Ø22.20 Mini Ø22.20 Mini (.874DIA Min.) (.874DIA Min.) 1.20 (.047) 1.20 (.047) 1.30 Mini (.051 Min.) 1.30 Mini (.051 Min.) Ø19.20 (.755DIA) Ø19.20 (.755DIA) AV19 003 940 Solder lug/quick-connect term. (short case) AV191003 240 AV9D 003 940 Solder lug / quick-connect terminals (short case only) AV9D1003 240 Panel cut-out -78 www.apem.com

Anti-vandal pushbutton switches Ø 22 mm (.866) Momentary () AV 3 40 (function 3) SERIES Bushing/act. configuration 03 Flat act. 02 Curved act. M3 Flat act + flatted bush. M2 Curved act.+ flatted bush. Case 000 Long 100 Short Function 3 Contacts A Silver C Brass, silver pl. Terminals 9 Screw 2 Quickconnect Bush./act. material 40 Stainless steel Sealing N No T Sealed In the following model numbers, replace with elements selected in the above order format. Flat actuator - short case - 48VDC - AV03100 Hex nut 25 (.984) across flats ø2x1.00 SI (.866DIAx1.00 IS) 7.30 (.287) 2.80 (.110) AV031003 940 1.20 (.047) Solder lug / quick-connect term. AV031003 240 ø25.00 ø15.00 (.59DIA) 2.80x0.5 (.110x.019) for wires 1,5 mm 2 max. 12.70 (.500) 6.30 (.248) 5.00 (.196) EPOXY Flat actuator - long case - 4A 250VAC/8A125VAC - UL/CSA - AV03000 Ø2x1.00 SI (.866DIAx1.00 IS) Hex nut 25 (.984) across flats AV030003A940 To order switches marked UL-CSA, add UU at the end of model number. (.59DIA) for wires 1,5 mm 2 max. 15.00 (.590) 10.00 (.248) 5.00 (.196) Curved actuator - AV02 3.60 (.141) Flatted bushing - AVM3 and AVM2 CAV03NUL AV02 003 940 Solder lug / quick-connect (short case) AV021003 240 Flat actuator, screw terminals AVM3 003 940 Curved actuator, screw terminals AVM2 003 940 Ø22.20 (.874DIA) Ø22.20 (.874DIA) Panel cut-out 10.00 (.393 ) 10.00 (.393 ) www.apem.com -79

Snap action security pushbutton switches Ø 16 mm (.629) Momentary () AV 3 0 C 9 OPTIONS (function 3) SERIES Bushing/act. configur. 06 Flat actuator 16 Curved actuator 08 Curved act.+chamfer 07 Flat act.+chamfer 6P Flat act.+knurled nut 6B Curved act.+knurled nut Function 3 Case 0 Short Contacts C Brass, silver pl. Terminals 9 Screw See Options page. SPECIFICATIONS Travel : 1,60 mm (.063) ± 0,3 mm (.011) Max. current/voltage rating with resistive load : 200mA 48 VDC - 100mA 48VDC Initial contact resistance : 50 mω max. Insulation resistance : 1.000 MΩ min. at 500VDC Dielectric strength : 0 Vrms 50 Hz min. between terminals and frame Electrical life : 50.000 cycles at 200mA 48VDC 100.000 cycles at 100mA 48VDC Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 6 mm (.236) max. Operating temperature : -30 C to +70 C Low level or mechanical life : 1.000.000 cycles Packaging unit : 60 pieces MATERIALS Case : PBT Contacts : brass, silver plated (C) Bushing and actuator : see Options page CUT-OUT Panel cut-out : Ø 16,2 mm (.637) Min. pitch for matrix mounting : 24 mm x 24 mm (.944 x.944) (AV6P & AV6B : 20 mm x 20 mm) To order a product, select a basic model below and add the desired options. Flat or curved actuator - screw terminals Hex nut 19 (.748) across flats 3.00 (.118) 3.00 (.118) Flat actuator AV0630C9 Curved actuator AV1630C9 Ø18.00 (.708DIA) Ø1 (.472DIA) Ø16.00X1.00 SI (.629DIAX1.00 IS) 1.50 (.059) 9.50 (.374) 11.20 (.440) for wires 1,5 mm 2 max. AV16DT1-A With chamfer With knurled nut for matrix mounting 20 x 20 - AV6P and AV6B 1.50 (.059) Ø18.00 (.708DIA) Ø1 (.472DIA) Ø18.00 (.708DIA) Ø1 (.472DIA) 20.00 (.787) 20.00 (.787) 20.00 (.787) Ø18.00 (.708DIA) Ø18.00 (.708DIA) Curved actuator AV0830C9 Flat actuator AV0730C9 Flat actuator AV6P30C9 Curved actuator AV6B30C9 FICHIER CAV6PDT1 Wrench available under P/N U1990. -80 www.apem.com

Security pushbutton switches Ø 16 mm (.629) Latching action AV 1 1 A OPTIONS OFF ON SERIES Actuator 06 Flat 16 Curved Function 1 Off-On Case 1 Long Contacts A Silver Terminals 2 Solder 4 PC 8 Quickconnect See Options page. SPECIFICATIONS Max. current/voltage rating with resistive load : 1A 24VDC Initial contact resistance : 50mΩ max. CAVDTF1SFCT Insulation resistance : 1 GΩ min. at 500VDC Dielectric strength : 1.500 Vrms 50 Hz min. between terminals 1 000 Vrms 50 Hz between terminals and frame Electrical life : 40.000 cycles Torque : 5 Nm min. - 14 Nm max. applied to nut Panel thickness : 1 (.039) to 6 mm (.236) max. Operating temperature : -30 C to +70 C Low level or mechanical life : 200.000 cycles Hand soldering : 300 C, 5 sec. max. Packaging unit : 25 pieces MATERIALS Case : PA-6T, UL94-V0 Contacts : silver (A) Gold plated silver (AD) on request Bushing and actuator : see Options page CUT-OUT Panel cut-out : Ø 16,2 mm (.637) Min. pitch for matrix mounting : 24 mm x 24 mm (.944 x.944) To order a product, select a basic model below and add the desired options. Flat or curved actuator - solder lug terminals Hex nut 19 (.748) across flats 3.00 (.118) 3.40 (.133) 3.00 (.118) 2.30 (.090) Flat actuator AV0611A2 OFF - ON Curved actuator AV1611A2 OFF - ON Ø18.00 (.708DIA) Straight PC terminals Quick-connect terminals 3.50 (.137) Ø1 (.472DIA) Ø18.00 (.708DIA) Ø1 (.472DIA) 1.40 (.055) Ø16.00X1.00 SI (.629DIAX1.00 IS) EPOXY 1.50 (.059) 9.00 (.354) 15.20 (.598) CAV06DTF1 3.50 (.137) 0.50 0.50 (.019) (.019) EPOXY EPOXY EPOXY EPOXY 8.00 (.314) 8.00 (.314) 5.08 5.08 (.200) (.200) 1.10 1.10 (.043) (.043) 0.50 0.50 (.019) (.019) 1.20 1.20 (.047) (.047) 2.40 (.094) 2.40 (.094) 2.80 2.80 (.047) (.047) Flat actuator AV0611A4 Curved actuator AV1611A4 Flat actuator AV0611A8 Curved actuator AV1611A8 CAV16COPC CAV16COSO www.apem.com -81

Security pushbutton switches Ø 16 mm (.629) Options After selecting basic model number, fill in last 2 boxes with desired options. Bushing/act. material Sealing BUSHING/ACTUATOR MATERIALS Flat or curved metal actuator CODE BUSHING ACTUATOR 00 (standard) Nickel plated brass Nickel plated brass 10 Nickel plated brass Stainless steel 40 Stainless steel Stainless steel SEALING Blank K No sealing Front panel sealing (IP65) -82 www.apem.com

Security pushbutton switches Ø 19 mm (.748) Momentary () AV 3 OPTIONS (function 3) SERIES Bushing/act. config. 09 Flat actuator 19 Curved actuator 9P Flat act., knurled nut 9B Curved act., knurled nut Case 000 Long 100 Short Function 3 Contacts A Silver C Brass silver pl. Terminals 9 Screw 2 Quickconnect See Options page. SPECIFICATIONS Max. current/voltage rating with resistive load : - A contacts : 4A 12VDC, 500.000 cycles - C contacts : 2A 48 VDC, 10.000 cycles Approved ratings of models with long case and A contacts (AV..000) : UL-CSA : 4A 250VAC - 8A 125VAC - 6.000 cycles Initial contact resistance : 10 mω max. Insulation resistance : 1.000 MΩ min. at 500VDC Dielectric strength : 0 Vrms 50 Hz min. between terminals and frame 0 Vrms 50 Hz min. between terminals Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 11 mm (.433) max. Operating temperature : -30 C to +70 C Low level or mechanical life : 1.000.000 cycles Hand soldering : 300 C, 3 sec. max. Packaging unit : 40 pieces To order a product, select a basic model below and add the desired options. Flat actuator - short case - 48VDC - AV09100 MATERIALS Case : PBT Contacts : silver (A) or brass, silver plated (C) Bushing and actuator : see Options page CUT-OUT Panel cut-out : Ø 19,2 mm (.755) Min. pitch for matrix mounting : 30 mm x 30 mm (1.181x1.181) (AV9P & AV9B : 25 mm x 25 mm) Hex nut 22 (.866) across flats ø19.00x1.00 SI (.748DIAx1.00 IS) 7.30 (.287) 2.80 (.110) AV091003 9 Solder lug / quick-connect term. AV091003 2 for wires 1,5 mm 2 max. ø2 ø15.00 13.50 (.531) 5.50 (.216) 5.00 (.196) 2.80x0.5 (.110x.019) 1.20 (.047) EPOXY Curved actuator - short case 3.60 (.141) Ø2 With knurled nut for matrix mounting 25 x 25 - AV9P and AV9B Ø2 Contacts : remplace with A (silver) or C (silver plated brass). 4.50 (.177) Ø2 4.50 (.177) 25.00 (.984) 25.00 25.00 (.984) (.984) AV191003 9 Solder lug / quick-connect terminals AV191003 2 Flat actuator, screw terminals AV9P1003 9 Flat actuator, solder lug term. AV9P1003 2 Curved actuator, screw terminals AV9B1003 9 Curved actuator, solder lug term. AV9B1003 2 Wrench available under P/N U1929 www.apem.com -83

Security pushbutton switches Ø 19 mm (.748) Momentary () Flat actuator - long case - 4A 250VAC/8A 125VAC - UL/CSA - AV09000 Hex nut 22 (.866) across flats Ø19.00x1.00 SI (.748DIAx1.00 IS) 5.00 (.196) AV090003A9 Ø2 To order switches marked UL-CSA, add UU at the end of model number. for wires 1,5 mm 2 max. 14.80 (.582) 10.50 (.413) Curved actuator - long case 3.60 (.141) Ø2 With knurled nut for matrix mounting 25 x 25 - AV9P and AV9B Ø2 4.50 (.177) Ø2 CAV09DTUL 4.50 (.177) 25.00 (.984) 25.00 25.00 (.984) (.984) AV190003A9 Flat actuator, screw terminals AV9P0003A9 Curved actuator, screw terminals AV9B0003A9 Wrench available under P/N U1929. -84 www.apem.com

Security pushbutton switches Ø 19 mm (.748) Options After selecting basic model number, fill in last 3 boxes with desired options. BUSHING/ACTUATOR MATERIALS Flat or curved metal actuator Bush./actuator material Marking Sealing CODE BUSHING ACTUATOR 00 (standard) Nickel plated brass Nickel plated brass 10 Nickel plated brass Stainless steel 12 Nickel plated brass Chrome plated brass 20 Chrome plated brass Chrome plated brass 30 Chrome plated brass Stainless steel 40 Stainless steel Stainless steel 80 Varnished polished brass Varnished polished brass Flat thermoplastic actuator CODE BUSHING ACTUATOR COLOUR 0 (standard) Nickel plated brass 2 Chrome plated brass 8 Varnished polished brass Replace with one of the following codes. 1 : blue - 1/4 : dark blue - 2 : black - 3 : green 4 : grey - 5 : yellow - 6 : red - 7/1: white 9 : orange MARKING - By engraving on flat or curved brass actuator (stainless steel on request) - by hot stamping on flat thermoplastic actuator 8.00 (0.314) 1.50 (0.059) (0.590DIA) CODE TYPE OF MARKING TYPE 0 to 9 Numbers 0 to 9 X Symbol * Y Symbol # A to N Letters A to N P to W Letters P to W 0 Letter O Letter O : same code and same design as number 0. For special symbols, consult factory. Minimum order : 500 pieces Select an option from each of the two tables below. CODE COLOUR OF MARKING COLOUR Brass actuator 0 (standard) Same as finish 2 Black Note : a finished product supplied in version 0 cannot be modified to version "2". Thermoplastic actuator 2 Black 7 White SEALING Blank No sealing 2 K Frontal panel sealing (IP65) CAVETKK-A 1 ➀ internal gasket ➁ external gasket www.apem.com -85

Security pushbutton switches Ø 19 mm (.748) Momentary (NC/) 3 1 2 4 Combined NC/ CAV19LPFCT Series Bushing diameter AV 19 Bush./act. config. Actuator style Bush./act. matl Contact/ terminals L 40 7 P B See below SPECIFICATIONS Max. current/voltage rating with resistive load : 5A 250VAC - 5A 125VAC - 6.000 cycles 5A 15VDC - 3A 30VDC - 50.000 cycles Initial contact resistance : 100 mω max. Insulation resistance : 1.000 MΩ min. at 500VDC Dielectric strength : 0 Vrms 50 Hz min. between term. and frame Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 9 mm (.354) max. Operating temperature : -20 C to +85 C Low level or mechanical life : 1.000.000 cycles Front panel sealing : IP65 and IP69K Packaging unit : 20 pieces MATERIALS Case : PA 6/6 Contacts : silver Bushing : stainless steel (std) Actuator : stainless steel (std) CUT-OUT Panel cut-out : Ø 19,2 mm (.755) Min. pitch for matrix mounting : 30 mm x 30 mm (1.181x1.181) All model numbers below are for switches with standard bushing/actuator material. Solder lug terminals - AV19..407 O-ring Hex nut 22 (.866) across flats 3.60 (.141) Ø19.00X1.00 SI (.748DIAX1.00 IS) 1.50 (.059) Flat actuator AV19LP407 4 0.50 (.019) Ø2 (.590) 2 1 3 Curved actuator AV19LB407 Ø2 (.590) 13.10 (.515) 12.60 (.496) 3.60 (.141) BUSHING/ACTUATOR MATERIALS For non-standard material, replace 40 with one of the following codes. CODE BUSHING ACTUATOR 00 Nickel plated brass Nickel plated brass 20 Chrome plated brass Chrome plated brass -86 www.apem.com

Security pushbutton switches Ø 19 mm (.748) With illuminated ring - momentary (NC/) Options : see next page. AV 9 2 CAV3-9FCT NC/ SERIES Bushing dia. 19 mm LED colour 0 : no LED - 1 : blue - V : green 5 : yellow - 6 : red - 7 : white - 9 : amber LED resistor 0 No resistor supplied 1 12VDC resistor 2 24VDC resistor 4 48VDC resistor Contacts 2 Silver Terminals 2 Solder / quick-connect F Flying leads C Cable ECHELLE 1 SPECIFICATIONS Travel : 2 mm ± 0,3 mm (.003) Max. current/voltage rating with resistive load : 1A 30VDC LED voltage : 12VDC, 24VDC or 48VDC (If not supplied by, a resistor must be series-connected by the user)** Initial contact resistance : 100 mω max. Insulation resistance : 10 MΩ min. at 500VDC Dielectric strength : 500 Vrms 50 Hz min. between terminals 1.000 Vrms 50 Hz min. between terminals and frame Electrical life : 250.000 cycles at full load Operating force : 5N ± 2N Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 6 mm (.236) max. Low level or mechanical life : 1.000.000 cycles Operating temperature : -30 C to +85 C Hand soldering : 350 C, 5 seconds max. Packaging unit : flying lead/cable models : 1 piece - other models : 40 pieces ** Resistor value = supply voltage - LED forward voltage LED forward current Flat actuator - solder lug terminals MATERIALS Case : polyamide, glass filled Contacts : silver Bushing : see next page Actuator : see next page Elastomeric membrane : silicone LED CUT-OUT Panel cut-out : Ø 19,2 mm (.755) Min. pitch for matrix mounting : 30 mm x 30 mm (1.181x1.181) To order a product, select a basic model below and add the desired LED colour and voltage. Then select the desired options on next page. Hex nut 22 (.866) across flats 2.20 (.086) NC Illuminated (select LED colour above) * AV9 022 ON - MOM Non-illuminated AV90022 ON - MOM - + Ø2 2.80x0.50 (.110x.019) Ø19.00x1.00 SI (.748DIAx1.00 IS) 2 (.866) NC 11.60 (.456) 12.10 (.476) 8.30 (.326) * No LED resistor supplied on this model. Flat actuator - flying lead terminals 2.20 (.086) Ø19.00x1.00 SI (.748DIAx1.00 IS) Hex nut 22 (.866) CAV9DT-1 across flats ECHELLE 1 Illuminated (select LED colour & resistor above) AV9 2F ON - MOM Ø2 Non-illuminated AV9002F ON - MOM 11.60 (.456) 12.10 200 (.476) (7.874) Ø1 (.472DIA) Wire colours : black: NC, orange:, red: LED anode (+), blue : LED cathode (-) www.apem.com ECHELLE 1-87 CAV9DT-2

Security pushbutton switches Ø 19 mm (.748) With illuminated ring - momentary (NC/) Flat actuator - cable terminals Hex nut 22 (.866) across flats Illuminated (select colour & resistor) AV9 2C ON - MOM 2.20 (.086) Ø19.00x1.00 SI (.748DIAx1.00 IS) Non-illuminated AV9002C ON - MOM Ø2 11.60 (.456) 12.10 200 (.476) (7.874) After selecting basic model No., fill in last 5 boxes with desired options. Flying lead protection Flying lead/ cable length Ring colour Bushing / plunger mat. ECHELLE 1 Sealing CAV9DT-3 FLYING LEAD PROTECTION 0 No protection and/or no flying leads 1 Heat-shrink sleeves 2 Tube + epoxy FLYING LEAD/CABLE LENGTH 000 No flying leads / no cable 020 Length 20 cm (standard) XXX Length in centimeters RING COLOURS CODE COLOUR CODE COLOUR 1 Blue 6 Red 2 Black * 7 Opal white (std) 3 Green 8 Translucent 4 Grey * 9 Orange 5 Yellow * non-illuminated only BUSHING/PLUNGER MATERIALS CODE BUSHING ACTUATOR 00 Nickel plated brass Nickel plated brass 40 Stainless steel 303 Stainless steel 303 4A Stainless steel 304 Stainless steel 304 4B Stainless steel 316 Stainless steel 316 70 Chrome pl. brass, black Chrome pl. brass, black Other : on request. SEALING Blank No sealing 2 1 K CAV3ET Front panel ECHELLE sealing 1 (IP67) ➀ internal membrane ➁ external gasket -88 www.apem.com

Security pushbutton switches Ø 19 mm (.748) Illuminated and non-illuminated - latching AV 1 E A OPTIONS SERISE Actuator type 09 Flat 19 Curved Bush./act. config. Illumin. 0 No L Illum. LED colour 0 No LED 1 Blue 3 Green 5 Yellow 6 Red Function Contacts Terminals 2 Solder 4 PC 8 Quickconnect See next page. CAVNFFCT SPECIFICATIONS Max. current/voltage rating with resistive load : 2A 48 VDC LED voltage and consumption : blue 3,5V 10mA, green : 2V 10mA yellow & red : 2V 20mA (a resistor must be series-connected by the user)** Initial contact resistance : 50 mω max. Insulation resistance : 1.000 MΩ min. at 500VDC Dielectric strength : 1 000 Vrms 50 Hz min. between terminals 500 Vrms 50 Hz min. between terminals and frame Electrical life : 500.000 cycles at 2A 48VDC Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 9 mm (.354) max. Operating temperature : -30 C to +70 C Low level or mechanical life : 1.000.000 cycles Hand soldering : 300 C, 4 seconds max. Packaging unit : 20 pieces ** Resistor value = supply voltage - LED forward voltage LED forward current MATERIALS Case : PA6T UL94-V0 Contacts : silver Bushing and actuator : see next page LED CUT-OUT Panel cut-out : Ø 19,2 mm (.755) Min. pitch for matrix mounting : 30 mm x 30 mm (1.181 x 1.181) To order a product, select a basic model below and add the desired options selected on next page. Standard actuator position : the actuator is flush in the non-latched position and recessed in the latched position. Non-illuminated - solder lug terminals Hex nut 22 (.866) across flats Flat actuator * AV09100EA2 ON - ON 3.60 (.141) Ø19.00x1.00 SI (.748DIAx1.00 IS) NC 2.30 (.090) 0.50 (.019) Curved actuator AV19100EA2 ON - ON Ø2 NC 1.40 (.055) * Also available with prominent actuator in the non-latched position 13.50 10.70 2.80 (.531) (.421) (.110) Illuminated - solder lug terminals Hex nut 22 (.866) across flats Flat actuator AV091L EA2 ON - ON Ø19.00x1.00 SI (.748DIAx1.00 IS) CAV19NFDT1 NC 2.30 (.090) 0.50 (.019) Ø2 Ø3.20 (.125DIA) NC 1.40 (.055) Replace with desired LED colour. 13.50 (.531) 10.70 (.421) 2.80 (.110) www.apem.com -89 CAV19NFLDT1

Security pushbutton switches Ø 19 mm (.748) Latching - Options Straight PC terminals Quick-connect terminals 2.40 (.094) 8.00 (.314) 3.40 (.133) 1.10 (.043) 1.20 (.047) 2.80 (.110) Replace 2 with 4 at the end of the model numbers shown on CAVNFCOPO previous page. Replace 2 with 8 at the end of the model numbers shown on previous page. CAVNFCOZO After selecting basic model number, fill in last 2 boxes with desired options. Bushing/ act. material Sealing BUSHING/ACTUATOR MATERIALS CODE BUSHING ATUATOR 00 (std) Nickel plated brass Nickel plated brass 10 Nickel plated brass Stainless steel 40 Stainless steel Stainless steel 50 Stainless steel Nickel plated brass SEALING Blank No sealing 1 2 K Frontal panel sealing (IP65) CAVNFET ➀ elastomeric membrane ➁ external gasket -90 www.apem.com

Tactile security pushbutton switches Ø 19 mm (.748) Illuminated and non-illuminated - momentary () AV C7 3 D OPTIONS (function 3) SERIES Actuator type Case Illumin. 09 Flat 0 No 19 Curved L Illum. Function Contact Terminals 2 Solder 9 Screw See next page SPECIFICATIONS Travel : 0,7 mm (.027) ±0,1 mm (.003) Max. current/voltage rating with resistive load : 50mA 24VDC LED voltage and consumption : 2-colour LED : 2V (3V max.) 20mA Other colours : 2V (3V max.) 10mA A resistor must be series-connected by the user ** Initial contact resistance : 100 mω max. Insulation resistance : 1.000 MΩ min. at 500VDC Dielectric strength : 500 Vrms 50 Hz min. between terminals 0 Vrms 50 Hz min. between terminals and frame Electrical life : 1.000.000 cycles at full load Operating force : 7 N ±-2N Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 6 mm (.236) max. Operating temperature : -30 C to +70 C Hand soldering : 270 C, 3 seconds max. Packaging unit : 40 pieces ** Resistor value = supply voltage - LED forward voltage LED forward current MATERIALS Case : PBT UL94-V0 Terminals : brass, gold plated Contacts : gold plated dome Bushing and actuator : see next page LED CUT-OUT Panel cut-out : Ø 19,2 mm (.755) Min. pitch for matrix mounting : 30 mm x 30 mm (1.181x1.181) To order a product, select a basic model below and add the desired options selected on next page. Flat actuator - non-illuminated Hex nut 22 (.866) across flats Ø19.00x1.00 SI (.748DIAx1.00 IS) 1.90 (.074) Solder lug terminals AV09C703D2 1.10 (.043) AV09C703D9 Ø2 Ø2 EPOXY 4.15 (.163) Also available with curved actuator : AV19C703D2 or AV19C703D9 13.50 (.531) 13.20 (.519) 13.50 (.531) 3.90 (.153) Flat actuator - illuminated CAVDTL-1A Hex nut 22 (.866) across flats Ø19.00x1.00 SI (.748DIAx1.00 IS) 1.90 (.074) Solder lug terminals AV09C7L3D2 1.10 (.043) AV09C7L3D9 + - Ø2 Ø2 Ø10.00 (.393DIA) EPOXY 4.15 (.163) 13.50 (.531) 13.20 (.519) 13.50 (.531) 3.90 (.153) CAVDTL-2A www.apem.com -91

Tactile security pushbutton switches Ø 19 mm (.748) Options After selecting basic model no., fill in last 4 boxes with desired options. Bushing/act. material LED colour Marking Sealing BUSHING/ACTUATOR MATERIALS Non-illuminated models Illuminated models CODE BUSHING ACTUATOR 00 (std) Nickel plated brass Nickel plated brass 10 Nickel plated brass Stainless steel 30 Chrome plated brass Stainless steel 40 Stainless steel Stainless steel 80 Varnished polished brass Varnished polished brass CODE BUSHING ACTUATOR 00 (std) Nickel plated brass Nickel plated brass 20 Chrome plated brass Chrome plated brass 40 Stainless steel Stainless steel 50 Stainless steel Nickel plated brass 80 Varnished polished brass Varnished polished brass LED COLOURS Blank No LED 1: Blue - 3 : Green - 5 : Yellow - 6 : Red - 7 : White - 9 : Amber - 2 : Red/green For flat or curved actuator. - by engraving on non-illuminated brass actuator (stainless steel on request). - by hot stamping on thermoplastic insert (illuminated actuators) 8.00 (0.314) MARKING 1.50 (0.059) Ø10.00 (0.393DIA) 1.00 (0.039) CODE TYPE OF MARKING TYPE 0 to 9 Numbers 0 to 9 X Symbol * Y Symbol # A to N Letters A to N P to W Letters P to W 0 Letter O Letter O : same code and same design as number 0. For special symbols, consult factory. Minimum order : 500 pieces Select an option from each of the two tables below. CODE COLOUR OF MARKING COLOUR Non-illuminated actuators 0 (standard) Same as finish 2 Black Note : a finished product supplied in version 0 cannot be modified to version "2". Illuminated actuators 2 Black (on white) SEALING Blank No sealing 2 K Front panel sealing (IP65) CAVETKK-A 1 ➀ internal gasket ➁ external gasket -92 www.apem.com

Tactile security pushbuttons Ø 19 mm (.748) with overmolded actuator Illuminated and non-illuminated - momentary () AV 9 D OPTIONS (function 3) SERIES Bush./act. configuration Illumination S0 No SL Illum. Contacts Terminals 2 Solder 9 Screw See next page SPECIFICATIONS Travel : 0,7 mm (.027) ± 0,1 mm (.003) Max. current/voltage rating with resistive load : 50mA 24VDC LED voltage and consumption : 2-colour LED : 2V (3V max.) 20mA Other colours : 2V (3V max.) 10mA (a resistor must be series-connected by the user)** Initial contact resistance : 100 mω max. Insulation resistance : 1.000 MΩ min. at 500VDC Dielectric strength : 500 Vrms 50 Hz min. between terminals 0 Vrms 50 Hz min. between terminals and frame Electrical life : 1.000.000 cycles at full load Operating force : 7 N ±2N - Sealing option K will increase the operating force. Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 6 mm (.236) max. Operating temperature : -30 C to +70 C Hand soldering : 270 C, 3 sec. max. Packaging unit : 16 pieces ** Resistor value = supply voltage - LED forward voltage LED forward current Flat actuator - solder lug terminals MATERIALS Case : PBT UL94-V0 Terminals : brass, gold plated Contacts : gold plated dome Bushing : see next page Actuator : stainless steel, with thermoplastic overmolding LED CUT-OUT Panel cut-out : Ø 19,2 mm (.755) Min. pitch for matrix mounting : 30 mm x 30 mm (1.181x1.181) To order a product, select a basic model below and add the desired options selected on next page. Hex nut 22 (.866) across flats 1.90 (.074) Illuminated AV9SLD2 1.10 (.043) Non-illuminated AV9S0D2 Ø2 Ø2 4.15 (.163) 9.80 (.385) 4.30 (.169) Also available with bushing Ø 22 (.866) : on request. Flat actuator - screw terminals Hex nut 22 (.866) across flats CAV9SDTL-1 9.00 (.354) Illuminated AV9SLD9 Non-illuminated AV9S0D9 Ø2 Ø2 9.80 (.385) 4.30 (.169) Also available with bushing Ø 22 (.866) : on request. CAV9SDTL-3 www.apem.com -93

Tactile security pushbuttons Ø 19 mm (.748) with overmolded actuator Options After selecting basic model no., fill in last 5 boxes with desired options. Bushing material Overmolding LED colour Actuator type Sealing BUSHING MATERIALS OVERMOLDING COLOURS LED COLOURS CODE MATERIAL 0 (std) Nickel plated brass 2 Chrome plated brass 4 Stainless steel 5 Gold plated brass 6 Chrome plated brass, satin 7 Chrome pl. brass, black 8 Varnished polished brass 9 Polished brass CODE COLOUR CODE COLOUR 1 Blue 6 Red 2 Black * 7 White 3 Green 8 Translucent 4 Grey * 9 Orange 5 Yellow * non-illuminated only ** To order a green LED for actuator style 002, always use code V. Other actuator styles can be ordered with LED code 3 or V. CODE COLOUR Blank No LED 1 Blue 2 Red/green 3 ** Green V ** Green, high intensity 5 Yellow 6 Red 7 White 9 Amber ACTUATOR STYLES The ring and symbols are obtained by photochemical engraving of a stainless steel insert. The insert is then overmolded in the desired colour. The following actuator styles are available. For other types, consult factory. CODE 001 002 003 004 005 DESCRIPTION Illuminated ring and disc Illuminated ring Arrow Loudspeaker OFF Opening RING/SYMBOL CODE 006 008 009 010 011 DESCRIPTION Validation Closing Standby Cancel Power SYMBOL SEALING Blank No sealing CAV9SBS Recommended panel mounting for IP69K 2 ECHELLE 1 1 K Front panel sealing (IP67) CAV9SETA ➀ internal membrane ➁ external gasket -94 www.apem.com ECHELLE1 K CAV9SET69K Front panel sealing (IP69K)

Tactile security pushbuttons Ø 22 mm (.866) with overmolded actuator Illuminated and non-illuminated - momentary () UG1410-A-R1 AV 3 D OPTIONS (function 3) SERIES Bush./act. configuration Illumination S0 No SL Illum. Contacts Terminals 2 Solder 9 Screw See next page SPECIFICATIONS Travel : 0,7 mm (.027) ± 0,1 mm (.003) Max. current/voltage rating with resistive load : 50mA 24VDC LED voltage and consumption : 2-colour LED : 2V (3V max.) 20mA Other colours : 2V (3V max.) 10mA (a resistor must be series-connected by the user)** Initial contact resistance : 100 mω max. Insulation resistance : 1.000 MΩ min. at 500VDC Dielectric strength : 500 Vrms 50 Hz min. between terminals 0 Vrms 50 Hz min. between terminals and frame Electrical life : 1.000.000 cycles at full load Operating force : 7 N ±2N - sealing option K will increase the operating force. Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 6 mm (.236) max. Operating temperature : -30 C to +70 C Hand soldering : 270 C, 3 sec. max. Packaging unit : 16 pieces ** Resistor value = supply voltage - LED forward voltage LED forward current Flat actuator - solder lug terminals MATERIALS Case : PBT UL94-V0 Terminals : brass, gold plated Contacts : gold plated dome Bushing : see next page Actuator : stainless steel, with thermoplastic overmolding LED CUT-OUT Panel cut-out : Ø 22,2 mm (.874) Min. pitch for matrix mounting : 30 mm x 30 mm (1.181x1.181) To order a product, select a basic model below and add the desired options selected on next page. Hex nut 25 (.984) across flats 1.90 (.074) Illuminated AV3SLD2 1.10 (.043) Non-illuminated AV3S0D2 EPOXY 4.15 (.163) 9.30 (.366) 4.80 (.188) Flat actuator - screw terminals C Hex nut 25 (.984) across flats Illuminated AV3SLD9 9.00 (.354) Non-illuminated AV3S0D9 9.30 (.366) 4.80 (.188) www.apem.com -95 C

Tactile security pushbuttons Ø 22 mm (.866) with overmolded actuator Options After selecting basic model no., fill in last 5 boxes with desired options. Bushing material Overmolding LED colour Actuator type Sealing BUSHING MATERIALS OVERMOLDING COLOURS LED COLOURS CODE MATERIAL 0 (std) Nickel plated brass 2 Chrome plated brass 4 Stainless steel 5 Gold plated brass 6 Chrome plated brass, satin 7 Chrome pl. brass, black 8 Varnished polished brass 9 Polished brass CODE COLOUR CODE COLOUR 1 Blue 6 Red 2 Black * 7 White 3 Green 8 Translucent 4 Grey * 9 Orange 5 Yellow * non-illuminated only ** To order a green LED for actuator style 002, always use code V. Other actuator styles can be ordered with LED code 3 or V. CODE COLOUR Blank No LED 1 Blue 2 Red/green 3 ** Green V ** Green, high intensity 5 Yellow 6 Red 7 White 9 Amber ACTUATOR STYLES The ring and symbols are obtained by photochemical engraving of a stainless steel insert. The insert is then overmolded in the desired colour. The following actuator styles are available. For other types, consult factory. CODE 001 002 003 004 005 DESCRIPTION Illuminated ring and disc Illuminated ring Arrow Loudspeaker OFF Opening RING/SYMBOL CODE 006 008 009 010 011 DESCRIPTION Validation Closing Standby Cancel Power SYMBOL SEALING Blank No sealing Recommended panel mounting for IP69K 2 1 K Front panel sealing (IP67) ➀ internal membrane ➁ external gasket K Front panel sealing (IP69K) -96 www.apem.com

Security pushbutton switches Ø 22 mm (.866) Momentary () AV 3 OPTIONS (function 3) SERIES Bushing/act. configuration 03 Flat actuator 02 Curved actuator M2 Curved act.+flatted bush. M3 Flat act.+flatted bush. Case 000 Long 100 Short Function 3 Contacts A Silver C Brass, silver pl. Terminals 9 Screw 2 Quickconnect See Options page. SPECIFICATIONS Max. current/voltage rating with resistive load : - A contacts : 4A 12VDC, 500.000 cycles - C contacts : 2A 48 VDC, 10.000 cycles Approved ratings of models with long case and A contacts (AV..000) : UL-CSA : 4A 250VAC - 8A 125VAC - 6.000 cycles Initial contact resistance : 10 mω max. Insulation resistance : 1.000 MΩ min. at 500VDC Dielectric strength : 0 Vrms 50 Hz min. between terminals and frame 0 Vrms 50 Hz min. between terminals Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 11 mm (.433) max. Operating temperature : -30 C to +70 C Low level or mechanical life : 1.000.000 cycles Hand soldering : 300 C, 3 sec. max. Packaging unit : 20 pieces To order a product, select a basic model below or on next page and add the desired options. Flat actuator - short case - 48VDC - AV03100 ø2x1.00 SI (.866DIAx1.00 IS) MATERIALS Case : PBT Contacts : silver (A) or brass, silver plated (C) Bushing and actuator : see Options page CUT-OUTS Panel cut-out : Ø 22,2 mm (.874) Min. pitch for matrix mounting : 30 mm x 30 mm (1.181x1.181) Hex nut 25 (.984) across flats 7.30 (.287) 2.80 (.110) AV031003 9 1.20 (.047) Solder lug / quick-connect term. AV031003 2 ø25.00 ø15.00 (.59DIA) 2.80x0.5 (.110x.019) for wires 1,5 mm 2 max. 12.70 (.500) 6.30 (.248) 5.00 (.196) EPOXY Curved actuator - short case 3.60 (.141) Contacts : remplace with A (silver) or C (silver plated brass). Flatted bushing - short case - AVM3 and AVM2 AV021003 9 Solder lug / quick-connect terminals AV021003 2 Flat actuator, screw terminals AVM31003 9 Curved actuator, screw terminals AVM21003 9 Ø22.20 (.874DIA) 10.00 (.393 ) www.apem.com -97

Security pushbutton switches Ø 22 mm (.866) Momentary () - momentary (NC) - alternate action Flat actuator - long case - 4A 250VAC/8A 125VAC - UL/CSA - AV03000 Ø2x1.00 SI (.866DIAx1.00 IS) Hex nut 25 (.984) across flats AV030003A9 (.59DIA) To order switches marked UL-CSA, add UU at the end of model number. for wires 1,5 mm 2 max. 15.00 (.590) 10.00 (.248) 5.00 (.196) Curved actuator - long case 3.60 (.141) Flatted bushing - long case - AVM3 and AVM2 AV020003A9 Flat actuator, screw terminals AVM30003 9 Curved actuator, screw terminals AVM20003 9 Ø22.20 (.874DIA) 10.00 (.393 ) MOMENTARY RMALLY CLOSED MODEL (NC) Bushing Ø 22 (.866) - AV..1200 Single pole, screw terminals, without marking Silver plated copper contacts (C) Max. current/voltage rating with resistive load : 2A 250VAC - 3A 125VAC - 2,5A 24VDC Dielectric strength : 0 Vrms 50 Hz min. betw. term. and frame 0 Vrms. 50 Hz min. between terminals Electrical life : 100.000 cycles at 0,3A 24VAC or DC 10.000 cycles at full load Packaging unit : 20 pieces Flat actuator AV031202C900 Curved actuator AV021202C900 Bushing Ø 22 (.866) - alternate action - AV..4700 Double pole, solder lug/quick-connect term., curved actuator Silver contacts Max. current/voltage rating with resistive load : 3(1,5)A 250VAC - 6A 125VAC - 3A 24VAC or DC Dielectric strength : 3.000 Vrms min. between terminals and frame Electrical life : 10.000 cycles at full load 50.000 cycles at 1A 24VAC or DC Mechanical life : 100.000 cycles Packaging unit : 10 pieces (.59DIA) (.59DIA) (.59DIA) 3.60 (.141) Ø2x1.00 SI (.866DIAx1.00 IS) 1.60 (.063) Hex nut 25 (.984) across flats Ø2x1.00 SI (.866DIAx1.00 IS) 1 (.551) 15.40 (.606) Ø3.00x0.50 (.118DIAx.0.50) 7.00 (.275) 13.20 (.519) Hex nut 25 (.984) across flats 0.50x2.80 (.019x.110) 5.80 (.228) 8.40 (.330) AV044746A200 ON - ON 3.60 (.141) 1 (.551) 20.60 7.20 (.811) (.283) Further specifications : see previous page. Bushing/actuator materials, marking and sealing : see options on next page. -98 www.apem.com

Security pushbutton switches Ø 22 mm (.866) Options After selecting basic model number, fill in last 3 boxes with desired options. BUSHING/ACTUATOR MATERIALS Flat or curved metal actuator Bush./actuator material Marking Sealing CODE BUSHING ACTUATOR 00 (standard) Nickel plated brass Nickel plated brass 10 Nickel plated brass Stainless steel 12 Nickel plated brass Chrome plated brass 20 Chrome plated brass Chrome plated brass 30 Chrome plated brass Stainless steel 40 Stainless steel Stainless steel 80 ** Varnished polished brass Varnished polished brass Flat thermoplastic actuator CODE BUSHING ACTUATOR COLOUR 0 (standard) Nickel plated brass 2 Chrome plated brass 8 Varnished polished brass Replace with one of the following codes. 1 : blue - 1/4 : dark blue - 2 : black - 3 : green 4 : grey - 5 : yellow - 6 : red - 7/1: white 9 : orange MARKING - By engraving on flat or curved brass actuator (stainless steel on request) - by hot stamping on flat thermoplastic actuator 8.00 (0.314) 1.50 (0.059) (0.590DIA) CODE TYPE OF MARKING TYPE 0 to 9 Numbers 0 to 9 X Symbol * Y Symbol # A to N Letters A to N P to W Letters P to W 0 Letter O Letter O : same code and same design as number 0. For special symbols, consult factory. Minimum order : 500 pieces Select an option from each of the two tables below. CODE COLOUR OF MARKING COLOUR Brass actuator 0 (standard) Same as finish 2 Black Note : a finished product supplied in version 0 cannot be modified to version "2". Thermoplastic actuator 2 Black 7 White SEALING Blank No sealing 2 K Frontal panel sealing (IP65) 1 ➀ internal gasket ➁ external gasket www.apem.com -99

Security pushbutton switches Ø 22 mm (.866) With illuminated ring - momentary (NC/) Options : see next page. AV 3 2 NC/ SERIES Bushing dia. 22 mm LED colour 0 : no LED - 1 : blue - V : green 5 : yellow - 6 : red - 7 : white - 9 : amber LED resistor 0 No resistor supplied 1 12VDC resistor 2 24VDC resistor 4 48VDC resistor Contacts 2 Silver Terminals 2 Solder / quick-connect F Flying leads C Cable SPECIFICATIONS Travel : 2 mm ± 0,3 mm (.003) Max. current/voltage rating with resistive load : 1A 30VDC LED voltage : 12VDC, 24VDC or 48VDC (If not supplied by, a resistor must be series-connected by the user)** Initial contact resistance : 100 mω max. Insulation resistance : 10 MΩ min. at 500VDC Dielectric strength : 500 Vrms 50 Hz min. between terminals 1.000 Vrms 50 Hz min. between terminals and frame Electrical life : 250.000 cycles at full load Operating force : 5N ± 2N Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 6 mm (.236) max. Low level or mechanical life : 1.000.000 cycles Operating temperature : -30 C to +85 C Hand soldering : 350 C, 5 seconds max. Packaging unit : flying lead/cable models : 1 piece - other models : 40 pieces ** Resistor value = supply voltage - LED forward voltage LED forward current Flat actuator - solder lug terminals MATERIALS Case : polyamide, glass filled Contacts : silver Bushing : see next page Actuator : see next page Elastomeric membrane : silicone LED CUT-OUT Panel cut-out : Ø 22,2 mm (.874) Min. pitch for matrix mounting : 30 mm x 30 mm (1.181x1.181) To order a product, select a basic model below and add the desired LED colour and voltage. Then select the desired options on next page. Hex nut 25 (.984) across flats NC 2.20 (.086) Illuminated (select LED colour above) * AV3 022 ON - MOM Non-illuminated AV30022 ON - MOM - + 2.80x0.50 (.110x.019) Ø2x1.00 SI (.866DIAx1.00 IS) 25.00 (.984) NC 11.60 (.456) 12.10 (.476) 8.30 (.326) * No LED resistor supplied on this model. Flat actuator - flying lead terminals Hex nut 25 (.984) across flats 2.20 (.086) Ø2x1.00 SI (.866DIAx1.00 IS) Illuminated (select LED colour & resistor above) AV3 2F ON - MOM Non-illuminated AV3002F ON - MOM 11.60 (.456) 12.10 200 (.476) (7.874) Ø1 (.472DIA) Wire colours : black: NC, orange:, red: LED anode (+), blue : LED cathode (-) -100 www.apem.com

Security pushbutton switches Ø 22 mm (.866) With illuminated ring - momentary changeover (NC/) Flat actuator - cable terminals Hex nut 25 (.984) across flats 2.20 (.086) Ø2x1.00 SI (.866DIAx1.00 IS) Illuminated (select colour & resistor) AV3 2C ON - MOM Non-illuminated AV3002C ON - MOM 11.60 (.456) 12.10 (.476) 200 (7.874) After selecting basic model No., fill in last 5 boxes with desired options. Flying lead protection Flying lead/ cable length Ring colour Bushing / plunger mat. Sealing FLYING LEAD PROTECTION 0 No protection and/or no flying leads 1 Heat-shrink sleeves 2 Tube + epoxy WIRE/CABLE LENGTH 000 No flying leads / no cable 020 Length 20 cm (7.874) - standard XXX Length in centimeters RING COLOURS CODE COLOUR CODE COLOUR 1 Blue 6 Red 2 Black * 7 Opal white (std) 3 Green 8 Translucent 4 Grey * 9 Orange 5 Yellow * non-illuminated only BUSHING/PLUNGER MATERIALS CODE BUSHING ACTUATOR 00 Brass, nickel plated Brass, nickel plated 40 Stainless steel 303 Stainless steel 303 4A Stainless steel 304 Stainless steel 304 4B Stainless steel 316 Stainless steel 316 70 Chrome pl. brass, black Chrome pl. brass, black Other : on request. SEALING Blank No sealing 2 1 K Front panel sealing (IP67) ➀ internal membrane ➁ external gasket www.apem.com -101

Security pushbutton switches Ø 22 mm (.866) Illuminated and non-illuminated - latching AV 1 E A OPTIONS SERIES Actuator type 03 Flat 02 Curved Bush./act. config. Illumin. 0 No L Illum. LED colour 0 No LED 1 Blue 3 Green 5 Yellow 6 Red Function Contacts Terminals 2 Solder 4 PC 8 Quickconnect See next page. SPECIFICATIONS Max. current/voltage rating with resistive load : 2A 48 VDC LED voltage and consumption : blue 3,5V 10mA, green : 2V 10mA yellow & red : 2V 20mA (a resistor must be series-connected by the user)** Initial contact resistance : 50 mω max. Insulation resistance : 1.000 MΩ min. at 500VDC Dielectric strength : 1 000 Vrms 50 Hz min. between terminals 500 Vrms 50 Hz min. between terminals and frame Electrical life : 500.000 cycles at 2A 48VDC Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 9 mm (.354) max. Operating temperature : -30 C to +70 C Low level or mechanical life : 1.000.000 cycles Hand soldering : 300 C, 4 seconds max. Packaging unit : 20 pieces ** Resistor value = supply voltage - LED forward voltage LED forward current MATERIALS Case : PA6T UL94-V0 Contacts : silver Actuator and bushing : see next page LED CUT-OUT Panel cut-out : Ø 22,2 mm (.874) Min. pitch for matrix mounting : 30 mm x 30 mm (1.181x1.181) To order a product, select a basic model below and add the desired options selected on next page. Standard actuator position : the actuator is flush in the non-latched position and recessed in the latched position. Non-illuminated - solder lug terminals Flat actuator * AV03100EA2 ON - ON Curved actuator AV02100EA2 ON - ON 3.80 (.149) Ø2x1.00 SI (.866DIAx1.00 IS) Hex nut 25 (.984) across flats NC 2.30 (.090) NC 0.50 (.019) 1.40 (.055) * Also available with prominent actuator in the non-latched position 12.70 11.50 2.80 (.500) (.045) (.110) Illuminated - solder lug terminals Flat actuator AV031L EA2 ON - ON Ø2x1.00 SI (.866DIAx1.00 IS) Hex nut 25 (.984) across flats NC 2.30 (.090) 0.50 (.019) Ø3.20 (.125DIA) NC 1.40 (.055) Replace with desired LED colour. 12.70 11.50 2.80 (.500) (.045) (.110) -102 www.apem.com

Security pushbutton switches Ø 22 mm (.866) Illuminated and non-illuminated - latching Straight PC terminals Quick-connect terminals 2.40 (.094) 8.00 (.314) 3.40 (.133) 1.10 (.043) 1.20 (.047) 2.80 (.110) Replace 2 with 4 at the end of the model numbers shown on previous page. Replace 2 with 8 at the end of the model numbers shown on previous page. After selecting basic model number, fill in last 2 boxes with desired options. Bushing/ act. material Sealing BUSHING/ACTUATOR MATERIALS CODE BUSHING ACTUATOR 00 (std) Nickel plated brass Nickel plated brass 10 Nickel plated brass Stainless steel 40 Stainless steel Stainless steel 50 Stainless steel Nickel plated brass SEALING Blank No sealing 1 2 K Frontal panel sealing (IP65) ➀ elastomeric membrane ➁ external gasket www.apem.com -103

Security pushbutton switches Ø 22 mm (.866) or 24 mm (.944) with large actuator Momentary (combined NC+) AV L OPTIONS Combined NC+ SERIES Bushing diameter 22 22 mm 24 24 mm Bush./act. config. Act. style P Flat B Curved C Recessed Bush./actuator material See next page Terminals 4 Quickconnect 2 Solder lug SPECIFICATIONS Max. current/voltage rating with resistive load : 5A 250VAC Initial contact resistance : 100 mω max. Insulation resistance : 1.000 MΩ min. at 500VDC Dielectric strength : 0 Vrms 50 Hz min. between terminals and frame Electrical life : 1.000.000 cycles at 1A 250VAC 100.000 cycles at full load Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 6 mm (.236) max. Operating temperature : -20 C to +55 C Low level or mechanical life : 3.000.000 cycles Front panel sealing : IP65 Hand soldering : 300 C, 5 sec. max. Packaging unit : 20 pieces (except black chrome plated : 16 pieces) MATERIALS Case : polyester, glass filled Contacts : silver/nickel alloy Bushing and actuator : see next page. CUT-OUT Panel cut-out : Ø 22,2 mm (.874) or Ø 24,2 mm (.952) Min. pitch for matrix mounting : 30 mm x 30 mm (1.181x1.181) or 33 mm x 33 mm (1.299x1.299) To order a product, select a basic model below or on next page and add the desired bushing/actuator materials. Flat actuator - AV22LP O-ring Hex nut 25 (.984) across flats 3.60 (.141) Quick-connect terminals AV22LP 4 Solder lug terminals AV22LP 2 Ø26.00 (1.023DIA) Ø20.00 (.787DIA) 0.50 (.019) Ø2X1.00 SI (.866DIAX1.00 IS) 7.10 (.279) 2.80X0.50 (.110X.019) 1.30 (.051) 3.00 (.118) 12.50 (.492) 12.80 (.503) 2.40 (.250) Curved actuator - AV22LB Recessed actuator - AV22LC Quick-connect terminals AV22LB 4 Solder lug terminals AV22LB 2 Quick-connect terminals AV22LC 4 Solder lug terminals AV22LC 2-104 www.apem.com

Security pushbutton switches Ø 22 mm (.866) or 24 mm (.944) with large actuator Momentary (combined NC+) Flat actuator - low profile - AV24LP O-ring Hex nut 27 (1.062) across flats 3.60 (.141) Quick-connect terminals AV24LP 4 Solder lug terminals AV24LP 2 Ø30.00 (1.181DIA) Ø20.00 (.787DIA) 1.30 (.051) 14.20 (.559) 13.00 (.511) 0.50 (.019) Ø2X1.00 SI (.944DIAX1.00 IS) 7.10 (.279) 2.40 (.250) 2.80X0.50 (.110X.019) 1.30 (.051) Curved actuator - AV24LB Recessed actuator - AV24LC Quick-connect terminals AV24LB 4 Solder lug terminals AV24LB 2 Quick-connect terminals AV24LC 4 Solder lug terminals AV24LC 2 BUSHING/ACTUATOR MATERIALS Models with non-anodized actuator CODE BUSHING ACTUATOR 40 (standard) Stainless steel Stainless steel 20 Chrome plated brass Chrome plated brass Models with anodized actuator CODE BUSHING ACTUATOR COLOUR 1 Black chrome plated brass 2 Chrome plated brass 4 Stainless steel Replace with one of the following codes : 1 : blue - 2 : black - 3 : pale green - 3F : dark green - 4 : natural - 5 : gold yellow 6 : red - 6B : maroon www.apem.com -105

Mushroom head security pushbutton switches Ø 22 mm (.866) Momentary (combined NC+) AV 22 PNA OPTIONS Combined NC+ SERIES Bushing diameter Bush./act. config. Actuator colour See below Terminals 4 Quickconnect 2 Solder lug SPECIFICATIONS Max. current/voltage rating with resistive load : 5A 250VAC Initial contact resistance : 100 mω max. Insulation resistance : 1.000 MΩ min. at 500VDC Dielectric strength : 0 Vrms 50 Hz min. between terminals and frame Electrical life : 1.000.000 cycles at 1A 250VAC 50.000 cycles at full load Torque : 5 Nm min.- 14 Nm max. applied to nut Panel thickness : 1 (.039) to 6 mm (.236) max. Operating temperature : -20 C to +55 C Low level or mechanical life : 1.000.000 cycles Front panel sealing : IP65 Hand soldering : 300 C, 5 sec. max. Packaging unit : 16 pieces MATERIALS Case : polyester, glass filled Contacts : silver/nickel alloy Bushing : brass, nickel plated Actuator : aluminium, anodized CUT-OUT Panel cut-out : Ø 22,2 mm (.874) Min. pitch for matrix mounting : 30 mm x 30 mm (1.181x1.181) To order a product, select a basic model below and add the desired actuator colour. Mushroom head actuator - AV22PNA O-ring Hex nut 25 (.984) across flats 3.60 (.141) Quick-connect terminals AV22PNA 4 Solder lug terminals AV22PNA 2 Ø30.00 (1.181DIA) 0.50 (.019) Ø2X1.00 SI (.866DIAX1.00 IS) 7.10 (.279) 2.80X0.50 (.110X.019) 1.30 (.051) 10.80 (.425) 8.60 (.338) 12.80 (.503) 2.40 (.250) ACTUATOR ADIZATION COLOURS 1 : blue - 2 : black - 3 : pale green - 3F : dark green - 4 : natural - 5 : gold yellow - 6 : red - 6B : maroon C -106 www.apem.com