Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-GM Available for : ADS-AL CA Rev. Date: October 04, 0 Doc. No.: ##66## 0004 GM Version FRançaise disponible en ligne au www.idatalink.com please visit www.idatalink.com/support for complete product details The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 0 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.
XX-XX ADS-AL(DL)-GM - PAGE X-X -3 install type SeLeCtiOn FEATURES Page of 9 ADS-AL(DL)-GM Doc. No.: ##66## 0004 MAKE MODEL YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS BUICK CADILLAC ARM OEM ALARM CHEVROLET DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK TRUNK/HATCH RELEASE POWER SLIDING DOOR (L) POWER SLIDING DOOR (R) RAP SHUTDOWN CTRL REAR DEFROST CTRL* HEATED SEATS CTRL* TACHOMETER OUTPUT** DOOR STAT OUTPUT FRONT (L) DOOR STAT OUTPUT FRONT (R) DOOR STAT OUTPUT REAR (L) DOOR STAT OUTPUT REAR (R) TRUNK STAT OUTPUT Allure 05-09 3 Century 00-05 LaCrosse 05-09 3 LeSabre / Ultra 00-05 3 Park Avenue 97-05 3 Rainier 04-07 3 Regal 00-04 Rendez-vous 0-07 Terraza 05-07 3 CTS 03-07 3 Deville 00-05 3 Escallade 99-0 Escallade 03-06 3 Escallade EXT 03-06 3 Seville 98-03 3 SLS 98-99 SLS 00-04 3 SRX 04-06 3 STS 98-99 STS 00-04 3 Astro 98-05 Avalanche 0 Avalanche 03-06 3 Blazer 98-05 Cavalier 00-05 Express 03-07 Express 98-0 Impala 00-05 Monte Carlo 00-05 S0 / S5 98-04 Silverado 99-0 Silverado 03-06 3 SSR 04-06 3 Suburban 99-0 Suburban 03-06 3 Tahoe 99-0 Tahoe 03-06 3 Trailblazer 0-09 3 Uplander 05-09 3 Venture 00-04 * See heated accessories notice. ** Tach output is not available on vehicles with a duramax engine. The PK3 indicator will remain ON during the remote start sequence and will only turn OFF upon takeover. Tach output is not available on these vehicles if they are equipped with a V8 engine.
XX-XX ADS-AL(DL)-GM - PAGE X-X 3-3 install type SeLeCtiOn FEATURES Page 3 of 9 ADS-AL(DL)-GM Doc. No.: ##66## 0004 MAKE MODEL YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS ARM OEM ALARM SATURN SAAB PONTIAC OLDSMOBILE ISUZU GMC HUMMER DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK TRUNK/HATCH RELEASE POWER SLIDING DOOR (L) POWER SLIDING DOOR (R) RAP SHUTDOWN CTRL REAR DEFROST CTRL* HEATED SEATS CTRL* TACHOMETER OUTPUT** DOOR STAT OUTPUT FRONT (L) DOOR STAT OUTPUT FRONT (R) DOOR STAT OUTPUT REAR (L) DOOR STAT OUTPUT REAR (R) TRUNK STAT OUTPUT H 03-07 3 Envoy 98-0 Envoy 0-09 3 Jimmy 98-05 Safari 98-05 Savana 98-0 Savana 03-07 Sierra / CK 98-0 Sierra / CK 03-06 3 Sonoma 98-04 Yukon / Denali 99-0 Yukon / Denali 03-06 3 Ascender 03-08 3 Hombre 98-00 Alero 4cyl 99-0 Alero 4cyl 0-04 Alero 6cyl 99-04 Aurora 00-03 3 Bravada 98-0 Bravada 0-04 3 Intrigue 98-99 Intrigue 00-0 Silhouette 00-04 Aztek 0-05 Bonneville 00-05 3 Grand Am 4cyl 99-0 Grand Am 4cyl 0-05 Grand Am 6cyl 99-05 Grand Prix 04-08 3 Montana 00-04 Montana SV6 05-09 3 Sunfire 00-05 97x 06-09 3 Relay 05-07 3 * See heated accessories notice. ** Tach output is not available on vehicles with a duramax engine. The PK3 indicator will remain ON during the remote start sequence and will only turn OFF upon takeover. Tach output is not available on these vehicles if they are equipped with a V8 engine.
XX-XX ADS-AL(DL)-GM PAGE X-X Page 4 of 9 ADS-AL(DL)-GM Doc. No.: ##66## 0004 Heated accessories notice notice NOTE I II View compatibility chart for applicable vehicles. in all supported vehicle, heated accessories will automatically be activated 5 seconds after the remote starter is engaged and this only if the engine temperature is below 0 C (3 F). MOVE THE FOLLOWING ITEMS IN YOUR SCHEMATIC WITH ALL LAYERS ON USE THE FOLLOWING LAYER SPECIFIC ITEMS AS WIRING AND TEXT TEMPLATES to activate applicable heated WIRING AND TEXT TEMPLATES accessories upon remote start regardless of engine temperature, connect [purple/ black] wire to ground. USE THE FOLLOWING LAYER SPECIFIC ITEMS AS EMS IN YOUR LAYERS ON BLUE/ BLACK RED GREEN/BLACK BLUE/BLACK RED/ BROWN DISABLE - PURPLE/YELLOW PURPLE/BLACK BLACK/ GREEN PURPLE/ to disable this feature, connect [purple/yellow] wire to ground. /BLACK /RED YELLOW BROWN/RED BROWN/YELLOW ORANGE/BLACK ORANGE/ ORANGE PINK/BLACK PINK BLUE/RED BLUE/YELLOW GREEN/RED GRAY/RED - DISABLE GRAY/YELLOW BLACK BLUE/ BLACK RED GREEN/BLACK BLUE/BLACK RED/ BROWN PURPLE/YELLOW ENABLE - PURPLE/BLACK BLACK/ GREEN PURPLE/ /BLACK /RED YELLOW BROWN/RED BROWN/YELLOW ORANGE/BLACK ORANGE/ ORANGE PINK/BLACK PINK BLUE/RED BLUE/YELLOW GREEN/RED - ENABLE GRAY/RED (NC) GRAY/YELLOW BLACK BLEU/ NOIR ROUGE VERT/NOIR BLEU/NOIR ROUGE/ BRUN DESACTIVER - MAUVE/JAUNE MAUVE/NOIR NOIR/ VERT MAUVE/ /NOIR /ROUGE JAUNE BRUN/ROUGE BRUN/JAUNE ORANGE/NOIR ORANGE/ ORANGE ROSE/NOIR ROSE BLEU/ROUGE BLEU/JAUNE VERT/ROUGE GRIS/ROUGE - DESACTIVER GRIS/JAUNE NOIR BLEU/ NOIR ROUGE VERT/NOIR BLEU/NOIR ROUGE/ BRUN MAUVE/JAUNE ACTIVER - MAUVE/NOIR NOIR/ VERT MAUVE/ /NOIR /ROUGE JAUNE BRUN/ROUGE BRUN/JAUNE ORANGE/NOIR ORANGE/ ORANGE ROSE/NOIR ROSE BLEU/ROUGE BLEU/JAUNE VERT/ROUGE - ACTIVE GRIS/ROUGE GRIS/JAUNE NOIR
Page 5 of 9 ADS-AL(DL)-GM Doc. No.: ##66## 0004 type - wiring diagram REMOTE STARTER TACH (AC) INPUT RIGHT SLIDING DOOR (-) OUTPUT LEFT SLIDING DOOR (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT REQUIRED -> IGNITION (+) OUTPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/ GROUND - BLACK V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/ AUTO-RELOCK (-) INPUT - BROWN LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK (NC) BLACK/ (NC) GREEN *TACH (AC) OUTPUT - PURPLE/ /BLACK (NC) /RED (NC) (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK (NC) ORANGE/ (NC) ORANGE - DATA (J850) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) DATA 3 4 5 6 7 8 9 0 3 4 5 6 OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH
Page 6 of 9 ADS-AL(DL)-GM Doc. No.: ##66## 0004 type - wiring diagram REMOTE STARTER TACH (AC) INPUT RIGHT SLIDING DOOR (-) OUTPUT LEFT SLIDING DOOR (-) OUTPUT DISARM ONLY (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT PK3 REQUIRED -> IGNITION (+) OUTPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT PASS KEY III THEFT DETERRENT : MODULE, BEHIND DRIVER SIDE DASH, RIGHT OF STEERING COLUMN YELLOW/BLACK (-) LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/ GROUND - BLACK V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/ DISARM ONLY (-) INPUT - BROWN LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK (NC) BLACK/ (NC) GREEN *TACH (AC) OUTPUT - PURPLE/ /BLACK - GROUND (-) /RED (NC) - STARTER ENABLE (-) OUTPUT YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK (NC) ORANGE/ (NC) ORANGE - DATA (J850) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) DATA 3 4 5 6 7 8 9 0 3 4 5 6 OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH
Page 7 of 9 ADS-AL(DL)-GM Doc. No.: ##66## 0004 type 3 - wiring diagram REMOTE STARTER TACH (AC) INPUT RIGHT SLIDING DOOR (-) OUTPUT LEFT SLIDING DOOR (-) OUTPUT DISARM ONLY (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT REQUIRED -> IGNITION (+) OUTPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/ GROUND - BLACK V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/ DISARM ONLY (-) INPUT - BROWN LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK (NC) BLACK/ (NC) GREEN *TACH (AC) OUTPUT - PURPLE/ /BLACK (NC) /RED (NC) (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK (NC) ORANGE/ (NC) ORANGE - DATA (J850) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) DATA 3 4 5 6 7 8 9 0 3 4 5 6 OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH
XX-XX ADS-AL(DL)-GM ADS-AL(DL)-GM 8 ADS-DL(TB)-PL 8 ADS-DL-GM 8 ADS-DLSL-GM 8 PAGE X-X Page 8 of 9 ADS-AL(DL)-GM Doc. No.: ##66## 0004 installation mode SeLeCtiOn Press and release programming button to select installation mode. LED flashes (X) once = LED flashes (X) twice = STANDARD HARDWIRE MODE! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. module PrOgramming PrOCedUre Insert key into ignition. 3 Wait, LED will turn solid GREEN for seconds. START Turn key to START position. 4 OFF Turn key to OFF position. 5 Module Programming Procedure completed.
XX-XX PATENT CLASSIC PAGE X-X - identify VeHiCLe notice year Page 9 of 9 ADS-AL(DL)-GM Doc. No.: ##66## 0004 Locate the Vehicle Identification Number (VIN) and identify the 0th character. 4 3 A 5 Y N 5 T A L 8 D 5 R 0 X Match the VIN s 0th character to its corresponding year. L > 990 S > 995 Y > 000 5 > 005 A > 00 M > 99 T > 996 > 00 6 > 006 B > 0 N > 99 V > 997 > 00 7 > 007 C > 0 P > 993 W > 998 3 > 003 8 > 008 D > 03 R > 994 X > 999 4 > 004 9 > 009 E > 04 LED STATUS Flashing RED DIAGNOSTICS DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming module diagnostics Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FaCtOry reset PrOCedUre DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all connectors. 3 4 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. When LED flashes red, RELEASE programming button. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. this product is protected by one or more of the following patents: U.S. LetterS Patent no. 5,79,55; 6,0,460; 6,43,004; 6,49,6; 6,75,47; 6,97,73; 6,346,876; 6,39,534; 6,59,4; 6,696,97; 6,756,885; 6,756,886; 6,77,67; 6,8,89; 6,94,750; 7,00,40; 7,03,86; 7,046,6; 7,06,37; 7,068,53; 7,05,830; 7,05,679; 7,4,083; 7,369,936; 7,378,945; 7,489,33; 7,50,937; Canadian Patent no.,30,48;,45,03;,46,670;,44,99;,45,0;,45,07;,45,038;,45,04;,50,893;,45,490;,45,96;,45,487; european Patent no.,053,8; de 69807-94T; U.S. 00045535; 006098; 0060984; 00400784; 008003036; 009007955; ep500565; 538038; 538037;