Index Vehicle Application Guide... Immobilizer Interface with OEM Immob. Receiver...

Transcription

1 Platform: DBALL/DBALL Rev.: 0509 Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide Door Lock and Convenience Interface for Audi and Volkswagen vehicles. Features include door locks, door trigger sensing, hood pin, trunk/hatch, ignition and tach output. This firmware does not support Immobilizer bypass. One () programmed OEM key must be wired into the vehicle to complete the installation of a remote starter. Index Vehicle Application Guide... Immobilizer Interface with OEM Immob. Receiver... Installation Type a - Regular Key - Automatic Transmission... Type b - Regular Key - Manual Transmission... Type a - Push-to-Start - Automatic Transmission... Type b - Push-to-Start - Manual Transmission... Locating Components... Vehicle Wiring Reference Charts... Programming Module Programming... Module Reset... Feature and Option List... Feature Programming LED Diagnostics & Troubleshooting... Limited One-Year Consumer Warranty... Quick Reference Guide Audi and Volkswagen are registered trademarks and property of their respective companies. 05 Directed. All rights reserved.

2 Platform: DBALL/DBALL Vehicle Application Guide Rev.: 0509 Page The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle. Vehicles DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Trunk / Hatch Release FOB-Control of aftermarket alarm with OEM remote RS-SmartStart RS-SmartStart.0 Compatible RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Driver Door Pin SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin ST-Brake Status (foot brake) ST- E-Brake Status * ST-Ignition Status Audi A D D D D D D D A (Smart Key) D D D D D D D S D D D D D D D S (Smart Key) D D D D D D D Volkswagen Golf D D D D D D D Golf (Smart Key) D D D D D D D *For the E-Brake sensing to become active, start the vehicle, then activate the E-Brake button. Legend: : DD & Wire-to-Wire (WW) W: Wire-to-Wire DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring Note: No Immobilizer bypass - one () working OEM key must be wired into the vehicle to complete the installation. 05 Directed. All rights reserved.

3 Platform: DBALL/DBALL Rev.: 0509 Page Immobilizer interface with OEM Immob. Receiver Type : Regular Key OEM Immobilizer Receiver -6 loops NC Relay : Orange/Red: 0 Common Relay : Yellow/Red: NO Relay : Brown/Red: RF Programming button DBALL/ LED DBALL 0 Remove battery from OEM Remote Control Red Brown Immobilizer ECU NOTE: - Your OEM remote may differ from the model shown in the illustrations. - Remove Battery from OEM FOB prior to performing the Key Wrap. - Make -6 loops and place them around the front of the plastic body of the vehicle's coded key as shown above. - Test and secure mounted loop before reassembling the vehicle. Type : Push-To-Start (PTS) OEM Immobilizer Receiver -6 loops NC Relay : Orange/Red: 0 Common Relay : Yellow/Red: NO Relay : Brown/Red: RF Programming button DBALL/ LED DBALL 0 Note: OEM immobilizer receiver is located on the underside of the steering column, where the ignition switch would normally be. Remove battery from OEM Remote Control Red Brown Immobilizer ECU NOTE: - Your OEM remote may differ from the model shown in the illustrations. - Remove Battery from OEM FOB prior to performing the Key Wrap. - Make -6 loops and place them around the front of the plastic body of the vehicle's coded key as shown above. - Test and secure mounted loop before reassembling the vehicle. 05 Directed. All rights reserved.

4 Platform: DBALL/DBALL Type a - Regular Key - Automatic Transmission Rev.: 0509 Page (-) Lock Output (+) Brake Status Input (-) Unlock Output (+) V: Red/Gray, pin 7-pin Conn. (C) (VESCM above driver kick panel) 8 6 [] (AC) Tach Input (-) Door Status Input (+) V Refer to Vehicle wiring reference charts on page 9 for more information on vehicle-specific connections. Starter Remote (-) Trunk Release Output (+) Parking Lights Output (+) Start Output (+) Ignition Input/Output (-) GWR (Status) (+) Ignition Output (+) Accessory Output (-) Hazards: pin (+) Brake: Black/Red, pin 58 7-pin Conn. (A) (VESCM above driver kick panel) 8 6 Ignition Switch at Steering Column Module (+) Starter: pin (-) Trunk Release:pin 7 HS CAN Low: Orange/Brown, pin (+) Key Sense: pin (+) Ignition : pin 6 HS CAN High: Orange/Green, pin (+) Ignition : pin 7 6 Refer to the Immobilizer Interface section on page for more information about the Key Wrap. Steering Column Module (see page 8 for Locating Components) HS CAN High: Tan/Black: (+) V HS CAN Low: Tan: Key Wrap: Orange/Red: 0 Key Wrap: Yellow/Red: Key Wrap: Brown/Red: (+) V: Red: : Black: (-) Hazard Output: Black/White: (-) Door/Trunk Status Output: Green/White: (-) Trunk Release Output: Red/Black: [] (AC) Tach Output: Violet/White: 5 (+) Brake Output: Gray: 6 (+) Brake Status Output: Violet/Green: 8 (+) Brake Status Output: Violet/Brown: 9 RF Prog. Button LED DBALL/ DBALL 0 0: Blue/White: (-) GWR (Status) Input 9: Pink: (+) Ignition Input 8: Violet: (+) Start Input 7: Pink/White: (+) Parking Lights Input : Red/White: (-) Trunk Release Input : Blue: (-) Unlock Input : Green: (-) Lock Input (+) V RX TX XKDD65 Not required in DD mode. [] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in DD. All adapters are displayed from the wire side (unless specified otherwise). 05 Directed. All rights reserved.

5 Platform: DBALL/DBALL Type b - Regular Key - Manual Transmission Rev.: 0509 Page 5 (-) E-Brake Status Input (+) Brake Status Input (-) Lock Output (-) Unlock Output (+) V: Red/Gray, pin (-) Hazard s: pin 7-pin Conn. (C) (VESCM above driver kick panel) 8 6 [] (AC) Tach Input (-) Door Status Input (+) V Refer to Vehicle wiring reference charts on page 9 for more information on vehicle-specific connections. Starter Remote (-) Trunk Release Output (+) Parking Lights Output (+) Start Output (+) Ignition Input/Output (-) GWR (Status) Ignition Switch at Steering Column Module (+) Starter: pin 6 (+) Ignition Output (+) Accessory Output (-) Clutch Switch: pin Clutch Switch Connector CUT (-) Clutch Switch: pin (-) Trunk Release: pin 7-pin Conn. (A) (VESCM above driver kick panel) 8 6 HS CAN Low: Orange/Brown, pin (+) Key Sense: pin HS CAN High: (+) Ignition :pin 6 Orange/Green, pin (+) Ignition : pin Refer to the Immobilizer Interface section on page for more information about the Key Wrap. Steering Column Module (see page 8 for Locating Components) HS CAN High: Tan/Black: HS CAN Low: Tan: (-) Clutch Interrupt (conn.side): Yellow: 8 (-) Clutch Interrupt (car side): Orange/Yellow: 9 Key Wrap: Orange/Red: 0 Key Wrap: Yellow/Red: Key Wrap: Brown/Red: (+) V (+) V: Red: : Black: (-) Hazard Output: Black/White: (-) Door/Trunk Status Output: Green/White: (-) Trunk Release Output: Red/Black: [](AC) Tach Output: Violet/White: 5 (+) Brake Status Output: Violet/Green: 8 (+) Brake Status Output: Violet/Brown: 9 (-) E-Brake Status Output: Yellow/Black: 0 (-)Clutch Output: Blue/Red: RF Prog. Button LED DBALL/ DBALL 0 0: Blue/White: (-) GWR (Status) Input 9: Pink: (+) Ignition Input 8: Violet: (+) Start Input 7: Pink/White: (+) Parking Lights Input : Red/White: (-) Trunk Release Input : Blue: (-) Unlock Input : Green: (-) Lock Input (+) V RX TX XKDD65 Not required in DD mode. [] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in DD. All adapters are displayed from the wire side (unless specified otherwise). 05 Directed. All rights reserved.

6 Platform: DBALL/DBALL Type a - Push-to-Start (PTS) - Automatic Transmission Rev.: 0509 Page 6 (+) Brake Status Input [] (AC) Tach Input (-) Door Status Input Refer to Vehicle wiring reference charts on page 9 for more information on vehicle-specific connections. (+) V Starter Remote (-) Lock Output (-) Unlock Output (-) Trunk Release Output (+) Parking Lights Output (+) Start Output (+) Ignition Input/Output (-) GWR (Status) (+) V: Red/Gray or Red/White, pin 7-pin Conn. (C) (VESCM above driver kick panel) (-) Hazards: pin pin Conn. (A) (VESCM above driver kick panel) 8 6 ESCLCM at Steering Column (see page 8 for Locating Components) (+) Brake: Black/Red, pin 58 (-) Trunk Release: pin [] x Amp DIODES Refer to the Immobilizer Interface section on page for more information about the Key Wrap. ESCLCM - Electronic Steering Column Lock Control Module 9 (-) PTS: pin HS CAN Low: Orange/Brown, pin 5 (-) PTS: pin 8 6 HS CAN High: Orange/Green, pin 6 HS CAN High: Tan/Black: HS CAN Low: Tan: Key Wrap: Orange/Red: 0 Key Wrap: Yellow/Red: Key Wrap: Brown/Red: (+) V (+) V: Red: : Black: (-) Hazard Output: Black/White: (-) PTS Output: Green/Black: (-) Door/Trunk Status Output: Green/White: [](-) Trunk Release Output: Red/Black: [](AC) Tach Output: Violet/White: 5 (+) Brake Output: Gray: 6 (+) Ignition Status Output: Gray/Black: 7 (+) Brake Status Output: Violet/Green: 8 (+) Brake Status Output: Violet/Brown: 9 RF Programming button LED DBALL/ DBALL 0 0: Blue/White: (-) GWR (Status) Input 9: Pink: (+) Ignition Input 8: Violet: (+) Start Input 7: Pink/White: (+) Parking Lights Input : Red/White: (-) Trunk Release Input : Blue: (-) Unlock Input : Green: (-) Lock Input (+) V RX TX XKDD65 Not required in DD mode. [] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in DD. [] Not required on the Volkswagen Golf. All adapters are displayed from the wire side (unless specified otherwise). 05 Directed. All rights reserved.

7 Platform: DBALL/DBALL Type b - Push-to-Start (PTS) - Manual Transmission Rev.: 0509 Page 7 (-) E-Brake Status Input (+) Brake Status Input [] (AC) Tach Input (-) Door Status Input (+) V Refer to Vehicle wiring reference charts on page 9 for more information on vehicle-specific connections. Starter Remote (-) Lock Output (-) Unlock Output (-) Trunk Release Output (+) Parking Lights Output (+) Start Output (+) Ignition Input/ Output (-) GWR (Status) (VESCM above driver kick panel) (+) V: 8 Red/Gray 6 or Red/White, pin (-) Hazard s: pin 7-pin Conn. (C) (-) Clutch Switch: pin Clutch Switch Connector CUT 5 (-) Clutch Switch: pin [] (-) Trunk Release: pin 7-pin Conn. (A) (VESCM above driver kick panel) 8 6 ESCLCM at Steering Column (see page 8 for Locating Components) Refer to the Immobilizer Interface section on page for more information about the Key Wrap. ESCLCM - Electronic Steering Column Lock Control Module x Amp DIODES 9 (-) PTS: pin HS CAN Low: Orange/Brown, pin 5 (-) PTS: pin 8 6 HS CAN High: Orange/Green, pin 6 HS CAN High: Tan/Black: HS CAN Low: Tan: (-) Clutch Interrupt (conn. side): Yellow: 8 (-) Clutch Interrupt (car side): Orange/Yellow: 9 Key Wrap: Orange/Red: 0 Key Wrap: Yellow/Red: Key Wrap: Brown/Red: (+) V (+) V: Red: : Black: (-) Hazard Output: Black/White: (-) PTS Output: Green/Black: (-) Door/Trunk Status Output: Green/White: [](-) Trunk Release Output: Red/Black: [](AC) Tach Output: Violet/White: 5 (+) Ignition Status Output: Gray/Black: 7 (+) Brake Status Output: Violet/Green: 8 (+) Brake Status Output: Violet/Brown: 9 (-) E-Brake Status Output: Yellow/Black: 0 (-) Clutch Output: Blue/Red: RF Programming button LED DBALL/ DBALL 0 0: Blue/White: (-) GWR (Status) Input 9: Pink: (+) Ignition Input 8: Violet: (+) Start Input 7: Pink/White: (+) Parking Lights Input : Red/White: (-) Trunk Release Input : Blue: (-) Unlock Input : Green: (-) Lock Input (+) V RX TX XKDD65 Not required in DD mode. [] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in DD. [] Not required on the Volkswagen Golf. All adapters are displayed from the wire side (unless specified otherwise). 05 Directed. All rights reserved.

8 Platform: DBALL/DBALL Locating Components Rev.: 0509 Page 8 VESCM - Vehicle Electrical System Control Module at Driver Side under dash, above Driver Kick Panel A B C ESCLCM - Electronic Steering Column Lock Control Module at Steering Column 05 Directed. All rights reserved.

9 Platform: DBALL/DBALL Rev.: 0509 Page 9 Vehicle Wiring Reference Charts Wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it. Type - Regular Key Make AUDI Model Year Function Connector Location Pin Wire A/S Keysense ESCLM 6-pin Connector 7 Yellow/Blue (+) Ignition ESCLM 6-pin Connector 6 Black/Red (+) Ignition ESCLM 6-pin Connector Yellow/Green (+) Start ESCLM 6-pin Connector 6 Red/Black (-) Hazards VESCM "C" Connector (7-pin) Violet/Red (+) Brake VESCM "C" Connector (7-pin) 58 Black/Red (-) Trunk VESCM "A" Connector (7-pin) Gray/Green (-) Clutch N/A N/A N/A Clutch (Interrupt) N/A N/A N/A Make VOLKSWAGEN Model Year Function Connector Location Pin Wire GOLF (All trim models) 05 Keysense ESCLM 6-pin Connector 7 Violet/Red (+) Ignition ESCLM 6-pin Connector 6 Black/White or Black (+) Ignition ESCLM 6-pin Connector Black/Green or Black/Gray (+) Start ESCLM 6-pin Connector 6 Red/Black or Black/Red (-) Hazards VESCM "C" Connector (7-pin) Brown/Red (+) Brake VESCM "C" Connector (7-pin) 58 Black/Red (-) Trunk VESCM "A" Connector (7-pin) White (-) Clutch Clutch Connector Violet/White Clutch (Interrupt) Clutch Connector White/Red Type - Push-to-Start Make AUDI Model Year Function Connector Location Pin Wire A/S (Smart Key) (-) Push-To-Start ESCLM 6-pin Connector Blue/White (-) Push-To-Start ESCLM 6-pin Connector Blue/Yellow (-) Hazards VESCM "C" Connector (7-pin) Violet/Red (+) Brake VESCM "C" Connector (7-pin) 58 Black/Red (-) Trunk VESCM "A" Connector (7-pin) Gray/Green (-) Clutch Clutch Connector Green/Blue Clutch (Interrupt) Clutch Connector Green/Gray Make VOLKSWAGEN Model Year Function Connector Location Pin Wire GOLF (Smart Key - All trim models) 05 (-) Push-To-Start ESCLM 6-pin Connector Violet (-) Push-To-Start ESCLM 6-pin Connector Violet/Blue (-) Hazards VESCM "C" Connector (7-pin) Brown/Red (+) Brake VESCM "C" Connector (7-pin) 58 Black/Red (-) Trunk VESCM "A" Connector (7-pin) N/A (-) Clutch Clutch Connector Violet/White Clutch (Interrupt) Clutch Connector White/Red 05 Directed. All rights reserved.

10 Platform: DBALL/DBALL Module Programming Rev.: 0509 Page 0 Refer to the LED Diagnostics section on page 5 for more information and for troubleshooting purposes. Important Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step. Warning! To take advantage of advanced features, you must use XpressVIP.5 or higher. Using version.9 or. will limit available functions and features.. Connect the interface module to your computer using the XKLoader.. Open an Internet Explorer browser (version 6 or higher), and go to The detail of the platform and firmware that is currently saved on the interface module will be indicated in the top right corner of the page.. Select the year, make and model of the vehicle; the page will refresh to display the compatible firmware.. In the search result page, select Flash Standard install, and follow the instructions provided on the screen. 5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module. 6. The following message will be displayed when the upload is completed: The flashing is successfully completed. You may now unplug the kit. You can now proceed with the programming instructions below. DD Installation If required for your installation, connect the 0-pin, -pin and -pin harnesses to the module, then connect the -pin DD harness. OR WW Installation If required for your installation, connect the 0-pin and -pin harnesses to the module, then connect the -pin harness to the module. th st st DD 0-pin DD 0-pin rd nd rd nd -pin -pin -pin -pin For vehicles with Regular Keys Wait until the LED turns ON solid red and press the Unlock button on the OEM remote. Note: To skip the transponder programming and use convenience features only, press the programming button 5 times. Solid & PRESS UNLOCK Turn the ignition ON. The LED flashes green. Key OFF IGN START & Flash The green LED turns ON for seconds and shuts off. Solid x secs & OFF Turn the ignition OFF. Key Out OFF IGN START You have successfully completed the module programming sequence. Go to the next page to make the module programming for PTS vehicles 05 Directed. All rights reserved.

11 Platform: DBALL/DBALL Rev.: 0509 For vehicles with PTS Page OR DD Installation If required for your installation, connect the 0-pin, -pin and -pin harnesses to the module, then connect the -pin DD harness. WW Installation If required for your installation, connect the 0-pin and -pin harnesses to the module, then connect the -pin harness to the module. th st st DD 0-pin DD 0-pin rd nd rd nd -pin -pin -pin -pin Wait until the LED turns ON solid red and press the Unlock button on the OEM remote. Note: To skip the transponder programming and use convenience features only, press the programming button 5 times. Solid & PRESS UNLOCK For vehicles with PTS, make sure the key is inside the vehicle. Key Inside the Vehicle Important: Do NOT press the brake pedal. Press the Push-to-Start (PTS) button once to turn the ignition ON. The LED flashes green. Do NOT press the brake pedal X ENGINE START STOP PUSH & Flash 5 The green LED turns ON for seconds and shuts off. Solid x secs & OFF 6 Press the Push-to-Start (PTS) button once more to turn the ignition OFF. X ENGINE START STOP PUSH You have successfully completed the module programming sequence. 05 Directed. All rights reserved.

12 Platform: DBALL/DBALL Module Reset Rev.: 0509 Page A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected. If required for your installation, connect the 0-pin & -pin harnesses to the module. Press and hold the programming button, then connect the -pin harness to the module. st DD 0-pin th nd rd -pin -pin Wait seconds until the LED turns ON solid orange then release the programming button. The LED turns ON solid red. & & Hard Reset Solid Release Solid Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and DD options) may have to be reconfigured. See the Feature & Option List section of this guide. If required for your installation, connect the 0-pin & -pin harnesses to the module. Press and hold the programming button, then connect the -pin harness to the module. st DD 0-pin th nd rd -pin -pin Wait seconds until the LED turns ON solid orange, and wait 0 more seconds until the LED starts to flash orange and red. Solid & Release the programming button. The LED turns ON solid red. Release & Solid 05 Directed. All rights reserved.

13 Platform: DBALL/DBALL Feature & Option List Rev.: 0509 Page It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on The web offers more options; however, manual configuration of the features is possible using the information on this page. * Default Option Feat. Operation /Option Description. No RF Output * Module is connected to a remote starter using a standard installation. RFTD Output Type Unlock Driver Priority OEM Security Equipped Light Control. RFTD Output Module is connected to an XL0 using an RSR or RXT installation (when available).. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).. Driver Priority * Unlocks only the driver door when the button is first pressed, and. All Unlocks all doors when the button is first pressed... Without OEM alarm Module is connected to a vehicle without an OEM Alarm system.. With OEM Alarm* Module is connected to a vehicle with an OEM Alarm system.. Flashing * Module will flash the turn markers every 0 seconds.. Disabled Doesn't operate any function in the vehicle.. Disabled Engine shutdown when door opens.. Enabled only by OEM Remote Enabled by OEM remote for 5 seconds after unlocking. 5 Vehicle Takeover. Enabled by OEM remote and aftermarket remote * Enabled by OEM remote or aftermarket remote for 5 seconds after unlocking.. Takeover controlled only by remote starter Takeover is activated for 5 seconds after pressing unlock button. * default option 05 Directed. All rights reserved.

14 Platform: DBALL/DBALL Rev.: 0509 Feature Programming To enter feature programming routine - Turn the ignition ON, then OFF. - Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after seconds). Release the Programming button. - The LED will flash green once slowly to indicate the feature number is. After a short delay, the LED flashes red rapidly to indicate the current option of feature (i.e. x green followed by x red indicates feature is set to option ). The flashing sequence will repeat until a new command is entered. Changing feature options - Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. - The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered. Accessing another feature - Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered. When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option. Once a feature is programmed - Other features can be programmed. - The feature programming can be exited. Programming Button Exiting feature programming - No activity for 0 seconds; after 0 seconds, the LED will turn ON orange for seconds to confirm the end of the programming sequence. OR - Press and HOLD the programming button for seconds. After seconds, the LED will turn ON orange for seconds to confirm the end of the programming sequence. Page 05 Directed. All rights reserved.

15 Platform: DBALL/DBALL LED Diagnostics & Troubleshooting Rev.: 0509 Page 5 LED Status Description Troubleshooting Module programming - Firmware specific Off OFF Module has no power. Make sure the DD harness is connector or that volt is present between the red and black wires. If the Volt is present, the module may be defective. Solid Solid red Module is powered. Waiting to begin the programming sequence. Verify your power lines (DD or WW). green green CAN bus detected, car detection in progress. Check the firmware name and version. red x red x FT CAN not detected. Check CAN connection. red x red x HS CAN not detected. Check CAN connection. red x red x Ignition not detected. Check the firmware name and version. red x red x VIN not detected. Check the firmware name and version. red x5 red x5 Internal error. Report the error to tech support. Active ground while running green Solid red & orange green green Solid red, then flashes orange green quickly Inactive ground while running GROUND OUT ON (GWR) command received. IGNITION ON command received. START ON command received. Otherwise, the Ground While Running (status) signal was lost or was never received by the module. Commands can come from RF, DD or WW. Otherwise, the ignition signal was not received by the module. In a WW install, it will show only if the ignition input wire is used. Otherwise, the start signal was not received by the module. In a WW install, it will show only if the ignition input wire is used. red x red x Run safe activate. red x red x Brake not detected. red x7 red x7 RFTD out put not activated in RSR mode. Change the RFTD output type to RFTD output. 05 Directed. All rights reserved.

16 Platform: DBALL/DBALL Limited One Year Consumer Warranty Rev.: 0509 Page 6 For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. ( DIRECTED ) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the Part ), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer s name, address, telephone number, the authorized licensed dealer s name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED S OPTION THE PART AS DESCRIBED ABOVE. This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold AS-IS and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part. For further details relating to warranty information of Directed products, please visit the support section of DIRECTED s website at: This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only. Protected by U.S. Patents: 5,79,55; 6,0,60 B *; 6,,00 B; 6,9,6 B; 6,75,7 B; 6,97,7 B; 6,6,876 B; 6,9,5 B; 6,59, B; 6,696,97 B; 6,756,885 B; 6,756,886 B; 6,77,67 B; 6,8,89 B; 6,9,750 B; 7,00,0 B; 7,05,80 B; 7,0,86 B; 7,06,6 B; 7,06,7 B; 7,068,5 B; 7,05,679 B; Cdn. Patent:,0,8;,,99;,5,0;,5,0;,5,07;,5,08;,5,0;,0,97;,6,670;,5,089; European Patent:,05,8; Pat. Pending:,9,06. Made in Canada. 05 Directed. All rights reserved.

17 Quick Reference Guide DBALL/DBALL-VW0 Vehicle Takeover with regular key Vehicle Takeover for PTS vehicles Press the remote start button on the transmitter to start the vehicle.* Press remote start button* Press the remote start button on the transmitter to start the vehicle.* Press remote start button* Press the Unlock button on the OEM or aftermarket remote.* Press Unlock button on either remote* Press the Unlock button on the OEM or aftermarket remote.* Press Unlock button on either remote* Enter the vehicle, while making sure the key fob is inside with you. Enter the vehicle Enter vehicle Enter vehicle Turn the key into the run/ignition position. Key OFF IGN START You can now press the brake pedal, put the car in gear and drive off. Ready to drive off * Your aftermarket remote may differ from the model shown in the illustrations. 5 You can now press the brake pedal, put the car in gear and drive off. Ready to drive off Note: If the brake is not pressed within 5 seconds after the unlock, takeover become inactive. If the takeover is inactive, Remote Starter will stop the engine when the door opens or when the brake is pressed. * Your aftermarket remote may differ from the model shown in the illustrations. Note: If the brake is not pressed within 5 seconds after the unlock, takeover become inactive. If the takeover is inactive, Remote Starter will stop the engine when the door opens 05 Directed. All rights reserved.

18 Quick Reference Guide DBALL/DBALL-VW0 Pit Stop Mode Notes The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running. Stop the vehicle in a safe parking spot and put the gear in Park (P). Press the button to remote start the vehicle.* & Stop & put vehicle in Park (P) Press remote start button* P Key type vehicle only: remove key from the ignition. Key OUT OFF ON START It is now safe to leave the engine running and exit the vehicle with the key in hand. Note: We recommend that you always lock the doors of your vehicle when leaving it unattended. Exit vehicle with Key * Your aftermarket remote may differ from the model shown in the illustrations. 05 Directed. All rights reserved.