IR2110(-1-2)(S)PbF/IR2113(-1-2)(S)PbF HIGH AND LOW SIDE DRIVER Product Summary

Data Sheet No. PD6147 rev.u Features Floating channel designed for bootstrap operation Fully operational to +5V or +6V Tolerant to negative transient voltage dv/dt immune Gate drive supply range from 1 to 2V Undervoltage lockout for both channels 3.3V logic compatible Separate logic supply range from 3.3V to 2V Logic and power ground ±5V offset CMOS Schmitt-triggered inputs with pull-down Cycle by cycle edge-triggered shutdown logic Matched propagation delay for both channels Outputs in phase with inputs Description The IR211/IR2113 are high voltage, high speed power MOSFET and IGBT drivers with independent high and low side referenced output channels. Proprietary HVIC and latch immune CMOS technologies enable ruggedized monolithic construction. Logic inputs are compatible with standard CMOS or LSTTL output, down to 3.3V logic. The output drivers feature a high pulse current buffer stage designed for minimum IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF HIGH AND LOW SIDE DRIVER Product Summary V OFFSET (IR211) 5V max. (IR2113) 6V max. I O +/- 2A / 2A V OUT 1-2V t on/off (typ.) 12 & 94 ns Delay Matching (IR211) 1 ns max. (IR2113) 2ns max. driver cross-conduction. Propagation delays are matched to simplify use in high frequency applications. The floating channel can be used to drive an N-channel power MOSFET or IGBT in the high side configuration which operates up to 5 or 6 volts. Typical Connection Packages 14-Lead PDIP IR211/IR2113 16-Lead SOIC IR211S/IR2113S (Refer to Lead Assignments for correct pin configuration). This/These diagram(s) show electrical connections only. Please refer to our Application Notes and DesignTips for proper circuit board layout. www.irf.com 1

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute voltages referenced to COM. The thermal resistance and power dissipation ratings are measured under board mounted and still air conditions. Additional information is shown in Figures 28 through 35. Symbol Definition Min. Units V B High side floating supply voltage (IR211) -.3 525 (IR2113) -.3 625 V S High side floating supply offset voltage V B - 25 V B +.3 V HO High side floating output voltage V S -.3 V B +.3 V CC Low side fixed supply voltage -.3 25 V LO Low side output voltage -.3 V CC +.3 V DD Logic supply voltage -.3 V SS + 25 V SS Logic supply offset voltage V CC - 25 V CC +.3 V IN Logic input voltage (HIN, LIN & SD) V SS -.3 V DD +.3 dv s /dt Allowable offset supply voltage transient (figure 2) 5 V/ns P D Package power dissipation @ T A +25 C (14 lead DIP) 1.6 W (16 lead SOIC) 1.25 R THJA Thermal resistance, junction to ambient (14 lead DIP) 75 C/W (16 lead SOIC) 1 T J Junction temperature 15 T S Storage temperature -55 15 T L Lead temperature (soldering, 1 seconds) 3 Recommended Operating Conditions The input/output logic timing diagram is shown in figure 1. For proper operation the device should be used within the recommended conditions. The VS and VSS offset ratings are tested with all supplies biased at 15V differential. Typical ratings at other bias conditions are shown in figures 36 and 37. Symbol Definition Min. Units V B High side floating supply absolute voltage V S + 1 V S + 2 V S High side floating supply offset voltage (IR211) Note 1 5 (IR2113) Note 1 6 V C V HO High side floating output voltage V S V B V CC Low side fixed supply voltage 1 2 V LO Low side output voltage VCC V DD Logic supply voltage V SS + 3 V SS + 2 V SS Logic supply offset voltage -5 (Note 2) 5 V V IN Logic input voltage (HIN, LIN & SD) V SS V DD T A Ambient temperature -4 C Note 1: Logic operational for V S of -4 to +5V. Logic state held for V S of -4V to -V BS. (Please refer to the Design Tip DT97-3 for more details). Note 2: When V DD < 5V, the minimum V SS offset is limited to -V DD. 2 www.irf.com

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF Dynamic Electrical Characteristics V BIAS (V CC, V BS, V DD ) = 15V, C L = 1 pf, T A = 25 C and V SS = COM unless otherwise specified. The dynamic electrical characteristics are measured using the test circuit shown in Figure 3. Symbol Definition Figure Min. Units Test Conditions t on Turn-on propagation delay 7 12 15 V S = V t off Turn-off propagation delay 8 94 V S = 5V/6V t sd Shutdown propagation delay 9 11 14 V S = 5V/6V ns t r Turn-on rise time 1 25 35 t f Turn-off fall time 11 17 25 MT Delay matching, HS & LS (IR211) 1 turn-on/off (IR2113) 2 Static Electrical Characteristics V BIAS (V CC, V BS, V DD ) = 15V, T A = 25 C and V SS = COM unless otherwise specified. The V IN, V TH and I IN parameters are referenced to V SS and are applicable to all three logic input leads: HIN, LIN and SD. The V O and I O parameters are referenced to COM and are applicable to the respective output leads: HO or LO. Symbol Definition Figure Min. Units Test Conditions V IH Logic 1 input voltage 12 9.5 V IL Logic input voltage 13 6. V OH High level output voltage, V BIAS - V O 14 1.2 V I O = A V OL Low level output voltage, V O 15.1 I O = A I LK Offset supply leakage current 16 5 V B =V S = 5V/6V I QBS Quiescent V BS supply current 17 23 V IN = V or V DD I QCC Quiescent V CC supply current 18 18 34 V IN = V or V DD µa I QDD Quiescent V DD supply current 19 15 3 V IN = V or V DD I IN+ Logic 1 input bias current 2 2 4 V IN = V DD I IN- Logic input bias current 21 1. V IN = V V BSUV+ V BS supply undervoltage positive going 22 7.5 8.6 9.7 threshold V BSUV- V BS supply undervoltage negative going 23 7. 8.2 9.4 threshold V CCUV+ V CC supply undervoltage positive going 24 7.4 8.5 9.6 threshold V V CCUV- V CC supply undervoltage negative going 25 7. 8.2 9.4 threshold I O+ Output high short circuit pulsed current 26 2. 2.5 V O = V, V IN = V DD PW 1 µs I O- Output low short circuit pulsed current 27 2. 2.5 A V O = 15V, V IN = V PW 1 µs www.irf.com 3

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF Functional Block Diagram Lead Definitions Symbol Description V DD HIN SD LIN V SS V B HO V S V CC LO COM Logic supply Logic input for high side gate driver output (HO), in phase Logic input for shutdown Logic input for low side gate driver output (LO), in phase Logic ground High side floating supply High side gate drive output High side floating supply return Low side supply Low side gate drive output Low side return 4 www.irf.com

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF Lead Assignments 14 Lead PDIP IR211/IR2113 16 Lead SOIC (Wide Body) IR211S/IR2113S 14 Lead PDIP w/o lead 4 IR211-1/IR2113-1 14 Lead PDIP w/o leads 4 & 5 IR211-2/IR2113-2 Part Number www.irf.com 5

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF V =15V cc HV = 1 to 5V/6V 1 µf.1 µf 9 3 6 5 1 7 11 12 13 2 1KF6 1.1 µf OUTPUT MONITOR HO 1KF6 IRF82 2 µh 1KF6 + 1µF dv S >5 V/ns dt Figure 1. Input/Output Timing Diagram Figure 2. Floating Supply Voltage Transient Test Circuit V =15V cc HIN SD LIN 1 µf.1 µf 9 3 6 5 1 7 11 12 13 2 1 C L C L.1 µf HO LO 1 µf V B + 15V - V S ( to 5V/6V) 1 µf Figure 3. Switching Time Test Circuit Figure 4. Switching Time Waveform Definition Figure 5. Shutdown Waveform Definitions Figure 6. Delay Matching Waveform Definitions 6 www.irf.com

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF 25 25 2 2 Turn-On Delay Time (ns) 15 1 Turn-On Delay Time (ns) 15 1 5 5-5 -25 25 5 75 1 Figure 7A. Turn-On Time vs. Temperature 1 12 14 16 18 2 VCC/VBS Supply Voltage (V) Figure 7B. Turn-On Time vs. VCC/VBS Supply Voltage 25 25 2 2 Turn-On Delay Time (ns) 15 1 5 Turn-Off Delay Time (ns) 15 1 5 2 4 6 8 1 12 14 16 18 2 VDD Supply Voltage (V) Figure 7C. Turn-On Time vs. VDD Supply Voltage -5-25 25 5 75 1 Figure 8A. Turn-Off Time vs. Temperature 25 25 Turn-Off Delay Time (ns) 2 15 1 5 Turn-Off Delay Time (ns) 2 15 1 5 Typ 1 12 14 16 18 2 VCC/VBS Supply Voltage (V) Figure 8B. Turn-Off Time vs. VCC/VBS Supply Voltage 2 4 6 8 1 12 14 16 18 2 VDD Supply Voltage (V) Figure 8C. Turn-Off Time vs. VDD Supply Voltage www.irf.com 7

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF 25 25 2 2 Shutdown Delay Time (ns) 15 1 Shutdown Delay time (ns) 15 1 5 5-5 -25 25 5 75 1 Figure 9A. Shutdown Time vs. Temperature 1 12 14 16 18 2 VCC/VBS Supply Voltage (V) Figure 9B. Shutdown Time vs. VCC/VBS Supply Voltage 25 1 Shutdown Delay Time (ns) 2 15 1 5 Typ Turn-On Rise Time (ns) 8 6 4 2 2 4 6 8 1 12 14 16 18 2 VDD Supply Voltage (V) -5-25 25 5 75 1 Figure 9C. Shutdown Time vs. VDD Supply Voltage Figure 1A. Turn-On Rise Time vs. Temperature 1 5 8 4 Turn-On Rise Time (ns) 6 4 Turn-Off Fall Time (ns) 3 2 2 1 1 12 14 16 18 2 VBIAS Supply Voltage (V) Figure 1B. Turn-On Rise Time vs. Voltage -5-25 25 5 75 1 Figure 11A. Turn-Off Fall Time vs. Temperature 8 www.irf.com

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF 5 15. 4 12. Turn-Off Fall Time (ns) 3 2 1 Logic "1" Input Threshold (V) 9. 6. 3. Min. Max 1 12 14 16 18 2 VBIAS Supply Voltage (V) Figure 11B. Turn-Off Fall Time vs. Voltage 15. -5-25 25 5 75 1 Figure 12A. Logic 1 Input Threshold vs. Temperature 15. Logic " 1" Input Threshold (V) 12 9 6 3 Logic "" Input Threshold (V) 12. 9. 6. 3. Min. 2 4 6 8 1 12 14 16 18 2 VDD Logic Supply Voltage (V) Figure 12B. Logic 1 Input Threshold vs. Voltage 15. -5-25 25 5 75 1 Figure 13A. Logic Input Threshold vs. Temperature 5. 12 4. Logic "" Input Threshold (V) 9 6 3 Min. High Level Output Voltage (V) 3. 2. 1. 2 4 6 8 1 12 14 16 18 2 VDD Logic Supply Voltage (V) Figure 13B. Logic Input Threshold vs. Voltage. -5-25 25 5 75 1 Figure 14A. High Level Output vs. Temperature www.irf.com 9

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF 5. 1. High Level Output Voltage (V) 4. 3. 2. 1. M ax. Low Level Output Voltage (V).8.6.4.2. 1 12 14 16 18 2 VBIAS Supply Voltage (V) Figure 14B. High Level Output vs. Voltage. -5-25 25 5 75 1 Figure 15A. Low Level Output vs. Temperature 1. 5 Low Level Output Voltage (V).8.6.4.2 Offset Supply Leakage Current (µa) 4 3 2 1. 1 12 14 16 18 2 VBIAS Supply Voltage (V) Figure 15B. Low Level Output vs. Voltage -5-25 25 5 75 1 Figure 16A. Offset Supply Current vs. Temperature 5 5 Offset Supply Leakage Current (µa) 4 3 2 1 VBS Supply Current (µa) 4 3 2 1 1 2 3 4 5 6 IR211 IR2113 VB Boost Voltage (V) Figure 16B. Offset Supply Current vs. Voltage -5-25 25 5 75 1 Figure 17A. VBS Supply Current vs. Temperature 1 www.irf.com

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF 5 625 4 5 VBS Supply Current (µa) 3 2 1 VCC Supply Current (µa) 375 25 1 12 14 16 18 2 VBS Floating Supply Voltage (V) Figure 17B. VBS Supply Current vs. Voltage -5-25 25 5 75 1 Figure 18A. VCC Supply Current vs. Temperature 625 1 5 8 VCC Supply Current (µa) 375 25 VDD Supply Current (µa) 6 4 2 1 12 14 16 18 2 VCC Fixed Supply Voltage (V) Figure 18B. VCC Supply Current vs. Voltage -5-25 25 5 75 1 Figure 19A. VDD Supply Current vs. Temperature 6 1 VDD Supply Current (µa) 5 4 3 2 1 2 4 6 8 1 12 14 16 18 2 VDD Logic Supply Voltage (V) Figure 19B. VDD Supply Current vs. VDD Voltage Logic "1" Input Bias Current (µa) 8 6 4 2-5 -25 25 5 75 1 Figure 2A. Logic 1 Input Current vs. Temperature www.irf.com 11

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF 6 5. Logic 1 Input Bias Current (µa) 5 4 3 2 1 Logic "" Input Bias Current (µa) 4. 3. 2. 1. 2 4 6 8 1 12 14 16 18 2 VDD Logic Supply Voltage (V) Figure 2B. Logic 1 Input Current vs. VDD Voltage. -5-25 25 5 75 1 Figure 21A. Logic Input Current vs. Temperature Logic Input Bias Current (µa) 5 4 3 2 1 2 4 6 8 1 12 14 16 18 2 VDD Logic Supply Voltage (V) Figure 21B. Logic Input Current vs. VDD Voltage VBS Undervoltage Lockout + (V) 11. 1. 9. 8. Min. 7. 6. -5-25 25 5 75 1 Figure 22. VBS Undervoltage (+) vs. Temperature 11. 11. VBS Undervoltage Lockout - (V) 1. 9. 8. 7. Min. VCC Undervoltage Lockout + (V) 1. 9. 8. 7. Min. 6. -5-25 25 5 75 1 Figure 23. VBS Undervoltage (-) vs. Temperature 6. -5-25 25 5 75 1 Figure 24. VCC Undervoltage (+) vs. Temperature 12 www.irf.com

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF 11. 5. 1. 4. VCC Undervoltage Lockout - (V) 9. 8. 7. Min. Output Source Current (A) 3. 2. 1. Min. 6. -5-25 25 5 75 1. -5-25 25 5 75 1 Figure 25. VCC Undervoltage (-) vs. Temperature Figure 26A. Output Source Current vs. Temperature 5. 5. 4. 4. Output Source Current (A) 3. 2. Output Sink Current (A) 3. 2. Min. 1. Min. 1.. 1 12 14 16 18 2 VBIAS Supply Voltage (V) Figure 26B. Output Source Current vs. Voltage. -5-25 25 5 75 1 Figure 27A. Output Sink Current vs. Temperature 5. 15 32V 4. Output Sink Current (A) 3. 2. Junction 1 75 5 14V 1V 1. Min. 25. 1 12 14 16 18 2 VBIAS Supply Voltage (V) Figure 27B. Output Sink Current vs. Voltage 1E+2 1E+3 1E+4 1E+5 1E+6 Frequency (Hz) Figure 28. IR211/IR2113 TJ vs. Frequency (IRFBC2) RGATE = 33Ω, VCC = 15V www.irf.com 13

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF 15 32V 15 32V 14V 14V Junction 1 75 5 1V Junction 1 75 5 1V 25 25 1E+2 1E+3 1E+4 1E+5 1E+6 Frequency (Hz) Figure 29. IR211/IT2113 TJ vs. Frequency (IRFBC3) RGATE = 22Ω, VCC = 15V 1E+2 1E+3 1E+4 1E+5 1E+6 Frequency (Hz) Figure 3. IR211/IR2113 TJ vs. Frequency (IRFBC4) RGATE = 15Ω, VCC = 15V 15 32V 14V 15 32V 14V Junction 1 75 5 1V Junction 1 75 5 1V 25 25 1E+2 1E+3 1E+4 1E+5 1E+6 Frequency (Hz) Figure 31. IR211/IR2113 TJ vs. Frequency (IRFPE5) RGATE = 1Ω, VCC = 15V 1E+2 1E+3 1E+4 1E+5 1E+6 Frequency (Hz) Figure 32. IR211S/IR2113S TJ vs. Frequency (IRFBC2) RGATE = 33Ω, VCC = 15V 15 32V 14V 15 32V 14V 1V Junction 1 75 5 1V Junction 1 75 5 25 25 1E+2 1E+3 1E+4 1E+5 1E+6 Frequency (Hz) Figure 33. IR211S/IR2113S TJ vs. Frequency (IRFBC3) RGATE = 22Ω, VCC = 15V 1E+2 1E+3 1E+4 1E+5 1E+6 Frequency (Hz) Figure 34. IR211S/IR2113S TJ vs. Frequency (IRFBC4) RGATE = 15Ω, VCC = 15V 14 www.irf.com

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF 15 32V 14V 1V. -2. Junction 1 75 5 VS Offset Supply Voltage (V) -4. -6. 25-8. 1E+2 1E+3 1E+4 1E+5 1E+6 Frequency (Hz) Figure 35. IR211S/IR2113S TJ vs. Frequency (IRFPE5) RGATE = 1Ω, VCC = 15V -1. 1 12 14 16 18 2 VBS Floating Supply Voltage (V) Figure 36. Maximum VS Negative Offset vs. VBS Supply Voltage 2. VSS Logic Supply Offset Voltage (V) 16. 12. 8. 4.. 1 12 14 16 18 2 VCC Fixed Supply Voltage (V) Figure 37. Maximum VSS Positive Offset vs. VCC Supply Voltage www.irf.com 15

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF Case Outlines 14-Lead PDIP 1-61 1-32 3 (MS-1AC) 14-Lead PDIP w/o Lead 4 1-61 1-38 2 (MS-1AC) 16 www.irf.com

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF 16 Lead PDIP w/o Leads 4 & 5 1-615 1-31 2 16-Lead SOIC (wide body) 1 615 1-314 3 (MS-13AA) www.irf.com 17

IR211(-1-2)(S)PbF/IR2113(-1-2)(S)PbF LEADFREE PART MARKING INFORMATION Part number IRxxxxxx Date code YWW? IR logo Pin 1 Identifier? MARKING CODE P Lead Free Released Non-Lead Free Released?XXXX Lot Code (Prod mode - 4 digit SPN code) Assembly site code ORDER INFORMATION Part only available Lead Free 14-Lead PDIP IR211 order IR211PbF 14-Lead PDIP IR211-1 order IR211-1PbF 14-Lead PDIP IR211-2 order IR211-2PbF 14-Lead PDIP IR2113 order IR2113PbF 14-Lead PDIP IR2113-1 order IR2113-1PbF 14-Lead PDIP IR2113-2 order IR2113-2PbF 16-Lead SOIC IR211S order IR211SPbF 16-Lead SOIC IR2113S order IR2113SPbF IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 9245 Tel: (31) 252-715 This product has been qualified per industrial level Data and specifications subject to change without notice 3/23/25 18 www.irf.com