Operating principle, characteristics Preventa safety s types XPS AV,, For and switch monitoring Operating principle Safety s XPS AV, and are used for monitoring circuits conforming to standards EN/ISO 850 and EN 6004- and also meet the safety requirements for the electrical monitoring of switches in protection devices conforming to standard EN 088. They provide protection for both the machine operator and the machine by immediately ping the dangerous movement on receipt of a instruction from the operator, or on detection of a fault in the safety circuit itself. Characteristics Module type In addition to the category 0 instantaneous opening safety ( for XPS AV, for and for ), the s incorporate category time delay ( for XPS AV, for and for ) which allow for controlled deceleration of the motor components until a complete is achieved (for example, motor braking by variable speed drive). At the end of the preset delay, the supply is disconnected by opening the time delay output circuits. For XPS AV, the time delay of the output circuits is adjustable, in 5 preset values, between 0 and 00 seconds using selector buttons. For, the time delay of the output circuits is adjustable between 0.5 and seconds or.5 and 0 seconds, depending on the model, using a selector switch. For, the time delay of the output circuits is adjustable between 0 and 0 seconds using a -position selector switch. Module XPS AV also incorporates solid-state signalling for signalling to the process PLC. Module incorporates 4 solid-state signalling for signalling to the process PLC. To aid diagnostics, the s have LEDs which provide information on the monitoring circuit status. The button monitoring function is confi gurable depending on the wiring. XPS AV, XPS AVP Maximum achievable safety level PL e/category 4 conforming to EN/ISO 849- SILCL (instantaneous safety and time delay safety ) conforming to EN/IEC 606 Reliability data (instantaneous safety ) Reliability data (time delay safety ) ppppc, ppppp PL e/category 4 (instantaneous safety ) and PL d/category (time delay safety ) conforming to EN/ISO 849-, SILCL (instantaneous safety ) and SILCL (time delay safety ) conforming to EN/IEC 606 pppp, ppppp Mean Time To dangerous Failure Years 75.8 5 4.8 (MTTF d) Diagnostic Coverage (DC) % > 99 > 99 > 99 Probability of dangerous Failure per Hour (PFH d) /h 7.95 x 0-9 x 0-8 6.8 x 0-9 Mean Time To dangerous Failure Years 75.8 5 54.5 (MTTF d) Diagnostic Coverage (DC) % > 99 > 60 and < 90 98.4 Probability of dangerous Failure per Hour (PFH d) /h 7.95 x 0-9 x 0-7.96 x 0-8 Conformity to standards EN/IEC 6004-, EN/IEC 60947-, EN/IEC 60947-5-, EN/ISO 850, EN 088/ISO 49, EN/IEC 6004-, EN/IEC 60947-, EN/IEC 60947-5-, EN/ISO 850, EN 088/ISO 49 PL e/category 4 (instantaneous safety ) and PL d/category (time delay safety ) conforming to EN/ISO 849-, SILCL (instantaneous safety ) and SILCL (time delay safety ) conforming to EN/IEC 606 EN/IEC 6004-, EN/IEC 60947-, EN/IEC 60947-5-, EN/ISO 850, EN 088/ISO 49 Product certifications UL, CSA, TÜV UL, CSA, BG UL, CSA, TÜV Supply Voltage V 4 c 4 c a and 4 c, 5 a, 0 a Voltage limits - 0 + 0% - 5 + 0% - 0 + 0% (4 V) - 5 + 5% (5 V) - 5 + 0% (0 V) Frequency Hz 50/60 Consumption W < 5 < < 8 Module inputs fuse protection Internal, electronic Adjustable time delay s 0 00 0.5 or,5 0 0 0 button monitoring Yes/No (confi gurable by terminal connections) Control unit voltage (at nominal supply voltage) Between input terminals S-S, S-S or S-S Between input terminals S-S, S-S or S-S 4 V version V 4 4 4 5 V, 0 V version V 48 Between input terminals S-S, S-S or S-B References: page 878-EN/4 Connections: page 878-EN/5 Dimensions: page 870-EN/ Characteristics: page 878-EN/ version: 7. 878-EN.indd
Characteristics (continued) Preventa safety s types XPS AV,, For and switch monitoring Characteristics (continued) Module type XPS... AV AVP ABVppppP ABVppppC ATEpppp ATEppppP Calculation of wiring resistance RL between input terminals Ω 00 max. Maximum cable length: 000 m Synchronisation time between inputs s For guard:.5 For : unlimited Outputs Voltage reference Volt-free Number and type of instantaneous opening safety circuits Number and type of time delay opening safety circuits RL = Ue Un x 60-7 Ue = true voltage applied to terminals A-A Un = nominal supply voltage RL max. = U int - U min. I min. Ue = true voltage applied to terminals A-A U int (terminals S-S) = supply voltage Ue - V (4 V version) U int between 4 V and 45 V, with typical value = 45 V (5 V, 0 V version) Calculated max. RL must be equal to or greater than the true value < 0.5 Approx. 0.075 For automatic start, terminals S-Y and Y-Y4 linked NO (0-04, -4, -4) NO (-4, -4) NO (-4, -4, -4) NO (7-8, 47-48, 57-58) NO (7-8) NO (57-58, 67-68, 77-78) Number and type of additional circuits solid-state 4 solid-state Breaking capacity in AC-5 Instantaneous VA C00: inrush 800, maintained 80 B00: inrush 600, maintained 60 C00: inrush 800, maintained 80 Time delay VA C00: inrush 800, maintained 80 B00: inrush 600, maintained 60 C00: inrush 800, maintained 80 Breaking capacity Instantaneous 4 V/.5 A L/R = 50 ms 4 V/.5 A L/R = 50 ms 4 V/.0 A L/R = 50 ms in DC- Time delay 4 V/.5 A L/R = 50 ms 4 V/.5 A L/R = 50 ms 4 V/.0 A L/R = 50 ms Breaking capacity of solid-state 4 V/0 ma Max. thermal current Instantaneous A. for all, or 6 for and 6 5 (Ithe) for, or 4 for and for Time delay A. for all, or 6 for and 6.5 for, or 4 for and for Max. total thermal current A 0 8 Output fuse protection, Instantaneous A 4 gg or 6 fast acting 6 gg 6 gg using fuses conforming to IEC/EN 60947-5-, Time delay A 4 gg or 6 fast acting 6 gg 4 gg DIN VDE 0660 part 00 Minimum current ma 0 () 0 0 () Minimum voltage V 7 () 7 7 () Electrical durability See page 860-EN/ Response time on instantaneous opening inputs ms < 0 < 00 < 0 Rated insulation voltage (Ui) V 00 (degree of pollution conforming to IEC/EN 60947-5-, DIN VDE 00 parts & ) Rated impulse withstand voltage (Uimp) kv 4 (overvoltage category III, conforming to IEC/EN 60947-5-, DIN VDE 00 parts & ) LED display 4 Operating temperature C - 0 + 55-5 + 55-0 + 55 Storage temperature C - 5 + 85-5 + 75-5 + 85 Degree of protection Terminals IP 0 conforming to IEC/EN 6059 Enclosure IP 40 Connections Type of terminals Captive screw Spring terminals Captive screw clamp terminals Type of terminal block Integrated in Removable from -wire connection Without cable end Solid or 0.4.5 mm Solid or 0..5 mm With cable end Without bezel, 0.5.5 mm With bezel, 0.5.5 mm -wire connection Without cable end Solid or 0.4 0.75 mm With bezel, 0.5.5 mm With bezel, 0.5.5 mm Solid or Solid or flexible cable: 0.4.5 mm 0.5.5 mm With bezel, With bezel, 0.5.5 mm 0.5.5 mm Solid or 0.4 0.75 mm With bezel, flexible cable: 0.5.5 mm Solid cable: 0. mm Solid or Solid cable: 0. mm Flexible cable: 0. mm 0..5 mm Flexible cable: 0..5 mm With cable end Without bezel, 0.5 mm Without bezel, flexible cable: 0.5 mm Double, with bezel, fl exible Double, with bezel, flexible Double, with bezel, flexible cable: 0.5.5 mm cable: 0.5.5 mm cable: 0.5 mm () The is also capable of switching low power loads (7 V/0 ma) provided that the contact has not been used for switching high power loads (possible contamination or wear of the gold layer on the contact tips). 878-EN.indd version: 7.
References Preventa safety s types XPS AV,, For and switch monitoring References Description Safety s for and switch monitoring Number of safety circuits 6 NO ( NO time delay) Additional Setting range of time delay Supply Connection Reference Weight solid-state 0 00 s 4 V c Captive screw integrated in kg XPS AV 0.0 6 NO ( NO time delay) solid-state 0 00 s 4 V c Captive screw XPS AVP 0.0 XPS AV NO ( NO time delay) 0.5 s 4 V c Captive screw P 0.80 4 V c Spring terminals C 0.75 XPS AVP.5 0 s 4 V c Captive screw XPS ABV0P 0.80 4 V c Spring terminals XPS ABV0C 0.75 5 NO ( NO time delay) 4 solid-state 0 0 s a/4 V c Captive screw integrated in 50 0.80 ppppp Captive screw 5 V a Captive screw integrated in 50P 0.80 40 0.80 ppppc Captive screw 40P 0.80 0 V a Captive screw integrated in 70 0.80 50 Captive screw 70P 0.80 4 version: 7. 878-EN.indd
Connections Preventa safety s type XPS AV For and switch monitoring XPS AV Module XPS AV associated with an button with NC contact, automatic start or unmonitored start To PLC channel Output Output channel Output Output Fault Time delay () Link for automatic start. () Instantaneous opening safety ( category 0). () Time delay opening safety ( category ). ESC = External start conditions. Functional diagrams Automatic start Power-up not S-S Automatic start (without ESC) S-S4 S-S S-S Time delay interrupt Y9-Y40 0-04/-4/-4 7-8/47-48/57-58 Y74 Y84 Automatic start There is no start contact or it is shunted. Unmonitored start The output is on closing of the start contact. not Tv = 0 00 s Time delay interrupted Unmonitored start Power-up not S-S button S-S4 S-S S-S Time delay interrupt Y9-Y40 0-04/-4/-4 7-8/47-48/57-58 Y74 Y84 not Tv = 0 00 s Time delay interrupted Monitored start The start input is monitored so that there is no start-up in the event of the start contact being shunted or the start circuit being closed for more than 0 seconds. -up is triggered following activation of the start button (push-release function) on opening of the contact. 878-EN.indd version: 7. 5
Connections (continued) Preventa safety s type XPS AV For and switch monitoring XPS AV Module XPS AV associated with an button with NC contacts, monitored start To PLC channel Output Output channel Output Output Fault Time delay () Instantaneous opening safety ( category 0). () Time delay opening safety ( category ). ESC = External start conditions. Functional diagram Monitored start Power-up not not S-S (channel ) S-S (channel ) S-S button S-S4 Time delay interrupt Y9-Y40 0-04/-4/-4 7-8/47-48/57-58 Y74 Y84 No start-up Tv = 0 00 s Time delay interrupted monitoring function configuration -channel wiring S -channel wiring, with short-circuit detection S A S S S S XPS AV A S S S S XPS AV A S S A S S 6 version: 7. 878-EN.indd
Connections (continued) Preventa safety s type XPS AV For and switch monitoring XPS AV Monitoring of a movable guard associated with switches Automatic start (diagram shown for guard closed) closed To PLC channel Output Output channel Output Output Fault closed Time delay () Instantaneous opening safety ( category 0). () Time delay opening safety ( category ). ESC = External start conditions. Functional diagram S-S (channel ) S-S (channel ) S-S open S-S4 Time delay interrupt Y9-Y40 0-04/-4/-4 7-8/47-48/57-58 Y74 Y84 LED details 5 678 Power-up closed 9 0 4 open closed open Tv = 0 00 s closed open Time delay interrupted S input status. S input status. S input status. 4 S4 input status. 5 S4 input status. 6 Y40 input status (time delay ). 7 K/K status (NO instantaneous opening safety ). 8 K/K4 status (time delay opening safety ). 9 Supply voltage A-A. 0 Fault. Confi guration mode. 878-EN.indd version: 7. 7
Connections (continued) Preventa safety s type For and switch monitoring Module XPS AV associated with an button with NC contacts, monitored start + 4 V F0 Feedback loop () () S F () F () F () A S S4 S5 7 Reset K Control logic K Supply Time (s) channel channel channel K K4 0 V A S S S S S 4 4 8 Stop category 0 Stop category 0 Safety Stop category S: S: button ESC = External start conditions. () With start button monitoring. () Without start button monitoring or automatic start. () Maximum fuse rating: see technical characteristics. or switch monitoring function configurations S S S S S4 S S ON -channel, manual start with S4 button monitoring Link ON S S S S S4 S S Short-circuit monitoring -channel, manual start with S4 button monitoring Link ON S S S S S S4 S S Short-circuit monitoring -channel, manual start with S4 button monitoring Link 4 S S S S S S5 S S Machine guard with short-circuit monitoring, automatic start Link or feedback loop for external contactors (automatic start S5) Link 8 version: 7. 878-EN.indd
Connections (continued) Preventa safety s type For and switch monitoring Functional diagrams monitoring: configurations, and Power-up Begin not Supply voltage (A-A). Channel (S-S) Begin. Channel S-S (S-S) Falling edge start S-S4 Rising edge start S-S5 Output -4, -4 (NO) Output 7-8 (NO) 0 tw >tm te ta tv >tm te >ta tw: Recovery time te: On-delay tm: Min. ON time ta: Response time tv: Off-delay (adjustable) ts: Synchronisation time Switch monitoring: configuration 4 Supply voltage (A-A) Power-up closed open closed. Channel (S-S). Channel S-S (S-S) Rising edge start S-S5 Output -4, -4 (NO) Output 7-8 (NO) 0 te ta tv tw ts te ta tw: Recovery time te: On-delay tm: Min. ON time ta: Response time tv: Off-delay (adjustable) ts: Synchronisation time LED details Supply voltage A-A K/K status K/K4 status 878-EN.indd version: 7. 9
Connections Preventa safety s type For and switch monitoring Module associated with an button Stop category 0 Instantaneous opening safety Stop category Time delay opening safety To PLC S: button with NC contacts (recommended application). S: button. ESC: External start conditions. Y (S) - Y: Feedback loop. F: 4 A max. () With start button monitoring. () Without start button monitoring. () The must be fuse protected. Technical characteristics for establishing maximum rating of fuses, see page 878-EN/. (4) 5/0 V a only. Functional diagram of with button monitoring Supply Begin voltage not With button Without button (O) Solid-state output Y89 (S) (O) Solid-state output Y90 (S) button button (O or O) Solid-state output Y89 (S) (O or O) Solid-state output Y90 (S) button Tmax. = 75 ms Outputs Solid-state output Y88 (A/A) Solid-state output Y9 (Stop ) Tv = 0 0 s Key 0 With start button monitoring (Y-Y5 connection). Without start button monitoring (Y-Y4 connection). Without start button (connection Y-Y4 and S-Y). Tv: adjustable time. LED details 4 External start conditions Output -4 (NO) Output -4 (NO) Output 57-58 (NO) Output 67-68 (NO) Output 77-78 (NO) 4 Supply voltage A-A, internal electronic fuse status. S (A) input status. S (B) input status. Stop category closed. 0 version: 7. 878-EN.indd
Connections (continued) Preventa safety s type For and switch monitoring Example of a safety circuit combining an with a variable speed drive PLC To PLC S: button with NC contacts (recommended application). S: button () With start button monitoring. () Technical characteristics for establishing maximum rating of fuses, see page 878-EN/. Connection with button Connection with multiple buttons S S A S S B S S 57 67 77 Both input channels are supplied at the same potential. S: button with NC contacts A short-circuit between the inputs is not detected. S S A S S B S S 57 67 77 The input channels are supplied at different potentials. A short-circuit between the inputs is detected. Configuration with start button monitoring (functional diagram for button, see page 878-EN/5 ) Monitoring an button with NC contact A PE S Y Y Y Y4 Y5 S () () Auxiliary terminal (to be used to separate the feedback loop from the wiring to the start button). Configuration without start button monitoring (functional diagram for button, see page 878-EN/5 ) S A S S B S S 57 67 77 S: button with NC contact. Not all faults are detected: a short-circuit on the pushbutton is not detected. A PE S Y Y Y Y4 Y5 S () () Auxiliary terminal (to be used to separate the feedback loop from the wiring to the start button). 878-EN.indd version: 7.