Fixed - Over/Under voltage limits, ( ) U N respectivity Link selectable - 5 min or 10 min delay. Fixed limits
|
|
- Audrey Pierce
- 5 years ago
- Views:
Transcription
1 Features Phase 230 V Over & Under voltage monitoring relays Fixed Over & Under voltage detection - Link selectable 5 or 10 minute lock-out delay Adjustable Over & Under voltage detection - Switch selectable 5 or 10 minute lock-out delay 35 mm rail (EN 60715) mounting LED indication Positive safety logic (healthy conditions - output relay energised) Fixed - Over/Under voltage limits, ( ) U N respectivity Link selectable - 5 min or 10 min delay Adjustable - symmetrical Over/Under voltage limits adjustable between ±5% to ±20% U N Switch selectable - 5 min or 10 min delay Detects and trips on out-of-limits L-N voltage, and protects against excessive starts/hour through power-on and lock-out time delays. Typical applications - protection of compressor motors and high pressure discharge lamp circuitry. Fixed limits Contact specification Contact configuration Rated current/maximum peak current A Rated voltage/maximum switching voltage V AC Rated load AC1 Rated load AC15 (230 V AC) Single phase motor rating (230 V AC) kw Breaking capacity DC1: 30/110/220 V A Minimum switching load mw (V/mA) Standard contact material Supply specification Nominal voltage (U N ) V AC (50/60 Hz) V DC Rated power AC/DC (50 Hz)/W Operating range AC DC Technical data Electrical life at rated load AC1 cycles Detection levels Switch-on lock-out time/reaction time Fault memory Electrical isolation: Supply to Measuring circuits Ambient temperature range C Protection category Approvals (according to type) 1 CO (SPDT) 1 CO (SPDT) 10/15 10/15 250/ /400 2,500 2, /0.3/ /0.3/ (5/5) 300 (5/5) / 4/ ( )U N ( )U N Fixed ( )U N Adjustable (±5 ±20)% U N (5 or 10)min / < 0.5 s (5 or 10)min / < 0.5 s None circuits are electrically common None circuits are electrically common IP 20 IP 20 1
2 Features Phase 400 V Over & Under voltage monitoring relay Adjustable Over & Under voltage detection - Switch selectable 5 or 10 minute lock-out delay 35 mm rail (EN 60715) mounting LED indication Positive safety logic (healthy conditions - output relay energised) Adjustable - symmetrical Over/Under voltage limits adjustable between ±5% to ±20% U N Switch selectable - 5 min or 10 min delay Delects and trips on out-of-limits L-L voltage, and protects against excessive starts/hour through power-on and lock-out time delays. Typical applications - protection of compressor motors and high pressure discharge lamp circuitry. Contact specification Contact configuration Rated current/maximum peak current A Rated voltage/maximum switching voltage V AC Rated load AC1 Rated load AC15 (230 V AC) Single phase motor rating (230 V AC) kw Breaking capacity DC1: 30/110/220 V A Minimum switching load mw (V/mA) Standard contact material Supply specification Nominal voltage (U N ) V AC (50/60 Hz) V DC Rated power AC/DC (50 Hz)/W Operating range AC DC Technical data Electrical life at rated load AC1 cycles Detection levels V (50/60 Hz) Switch-on lock-out time/reaction time Fault memory Electrical isolation: Supply to Measuring circuits Ambient temperature range C Protection category Approvals (according to type) 1 CO (SPDT) 10/15 250/400 2, /0.3/ (5/5) 400 4/ ( )U N Adjustable (±5...±20)% U N (5 or 10)min / < 0.5 s None circuits are electrically common IP 20 2
3 Features Phase 400 V - Line monitoring relays Over & Under voltage trip on-delay - Fault memory Phase asymmetry - Phase rotation - Phase loss 35 mm rail (EN 60715) mounting LED indication Positive safety logic (healthy conditions - output relay energised) 3 phase 400 V - line voltage monitoring Detects over and under voltage Adjustable trip on-delay Switch selectable fault memory 3 phase asymmetry monitoring Phase rotation monitoring Phase loss monitoring Under voltage trip level ( )U N - Adjustable Over voltage trip level 1.15 U N - Fixed Trip delay time (0.1 12)s adjustable Fault memory, switch selectable Fault acknowledgement by switch manipulation from ON to OFF and back to ON or power down Asymmetry between phases ( 5 20)% U N adjustable Detection of the supply voltage U to A1 (1) and/or A2 (5) > 1.11 U N L1 L2 L3 A1 A2 A U= 400 V AC 3~ (50/60 Hz ) 3~U ASY Contact specification Contact configuration Rated current/maximum peak current A Rated voltage/maximum switching voltage V AC Rated load AC1 Rated load AC15 (230 V AC) Single phase motor rating (230 V AC) kw Breaking capacity DC1: 30/110/220 V A Minimum switching load mw (V/mA) Standard contact material Supply specification Nominal voltage (U N ) V AC (50/60 Hz) V DC Rated power AC/DC (50 Hz)/W Operating range AC DC Technical data Electrical life at rated load AC1 cycles Detection level U min /U max /Asymmetry Trip on-delay/reaction time Fault memory - selectable Electrical isolation: Supply to Measuring circuits Ambient temperature range C Protection category Approvals (according to type) CO (SPDT) 1 CO (SPDT) 10/15 10/15 250/ /400 2,500 2, /0.3/ /0.3/ (5/5) 300 (5/5) / 4/ ( )U N ( )U N ( )U N / 1.15 U N / 0.7 U N / 1.11 U N /( )% U N ( )s / < 0.5 s / < 0.5 s Yes None circuits are electrically common None circuits are electrically common IP 20 IP 20 3
4 Features Universal voltage or current detecting and monitoring relay Voltage monitoring Current monitoring Zero voltage memory according to EN Programmable for DC or AC detection level: range detecting: upper and lower value upper set point minus hysteresis range (5...50)% for switch on lower set point plus hysteresis range (5...50)% for switch on Fault memory Electrical isolation between measuring and supply circuits Immune to supply interruptions of < 200 ms Wide detecting range: voltage: DC ( )V, AC ( )V 35 mm rail (EN 60715) mounting Programmable universal current monitoring relay Programmable universal current monitoring relay Usable with current transformer 50/5, 100/5, 150/5, 250/5, 300/5, 400/5 or 600/5 AC/DC voltage detection - adjustable AC (50/60 Hz) (15 480)V DC ( )V Switch-on hysteresis (5 50)% Switch-off delay (0.1 12)s AC/DC current detection - adjustable AC(50/60Hz) ( )A with current transformer to 600A DC ( )A Switch-on hysteresis (5...50)% Switch-off delay (0.1 12)s Start delay (0.1 20)s programmable programmable Contact specification Contact configuration Rated current/maximum peak current A Rated voltage/maximum switching voltage V AC Rated load AC1 Rated load AC15 (230 V AC) Single phase motor rating (230 V AC) kw Breaking capacity DC1: 30/110/220 V A Minimum switching load mw (V/mA) Standard contact material Supply specification Nominal voltage (U N ) V AC (50/60 Hz) V DC Rated power AC/DC (50 Hz)/W Operating range AC DC Technical data Electrical life at rated load AC1 cycles Detection levels AC(50/60 Hz)/DC Switch-off/reaction/Start delay Switch-on level of the detecting level % Fault memory - programmable Electrical isolation: Supply to Measuring circuits Ambient temperature range C Protection category Approvals (according to type) 1 CO (SPDT) 1 CO (SPDT) 10/15 10/15 250/ /400 2,500 2, /0.3/ /0.3/ (5/5) 300 (5/5) / 4 / ( )U N ( )U N ( )V/( )V (0.1 10)A at transducer to 600A / (0.1 10)A (0.1 12)s / < 0.35 s / < 0.5 s (0.1 12)s / < 0.35 s / (0.1 20)s Yes Yes Yes Yes IP 20 IP 20 4
5 Features x.xxx x.xxx.0001 Thermistor temperature sensing relays for industrial applications Pole, without fault memory Pole, with fault memory Overload protection according EN Positive safety logic - make contact opens if the measured value is outside of the acceptable range Industry standard module LED status indication 35 mm rail (EN 60715) mounting Thermistor relay 1 Pole normally open contact 24 V AC/DC, or 230 V AC supply Temperature detection with PTC PTC short circuit detection PTC wire breakage detection Thermistor relay with fault memory 2 Pole changeover contacts 24 V AC/DC, or 230 V AC supply Temperature detection with PTC Fault memory switch selectable Reset by Reset button or supply interruption PTC short circuit detection PTC wire breakage detection Contact specification Contact configuration Rated current/maximum peak current A Rated voltage/maximum switching voltage V AC Rated load AC1 Rated load AC15 (230 V AC) Single phase motor rating (230 V AC) kw Breaking capacity DC1: 30/110/220 V A Minimum switching load mw (V/mA) Standard contact material Supply specification Nominal voltage (U N ) V AC (50/60 Hz) V AC/DC Rated power AC/DC (50 Hz)/W Operating range AC DC Technical data Electrical life at rated load AC1 cycles PTC detecting: Short circuit/temperature OK Reset/PTC break Delay time/activaction time Fault memory - switch selectable Electrical isolation: Supply to Measuring circuits Ambient temperature range C Protection category Approvals (according to type) 1 NO (SPST-NO) 2 CO (DPDT) 10/15 10/15 250/ /400 2,500 2, /0.3/ /0.3/ (5/5) 300 (5/5) /0.5 1/0.5 ( )U N ( )U N <20 Ω / >20 Ω... <3 kω <20 Ω / >20 Ω... <3 kω <1.3 kω / >3 kω <1.3 kω / >3 kω / < 0.5 s / < 0.5 s Yes Yes Yes IP 20 IP 20 5
6 Ordering information 71 Series - Monitoring relays 10 A Example: Universal voltage monitoring relay with LCD display for AC/DC voltage detection, 1 CO (SPDT) contact rated 10 A 250, supply voltage 230 V, programmable delay time and fault memory Series Type 1 = 1 phase AC line monitoring 3 = 3 phase AC line monitoring 4 = AC/DC universal- Voltage detection 5 = AC/DC universal- Current detection 9 = Thermistor relay (temperature monitoring with PTC thermistor) No. of poles 1 = 1 CO (SPDT) types 71.11, 31, 41, 51 1 = 1 NO (SPST-NO) type = 2 CO (DPDT) type Supply version 0 = AC(50/60Hz)/DC 8 = AC (50/60 Hz) Supply voltage 024 = 24 V AC/DC 230 = 230 V 400 = 400 V Additional functions 0 = Basic function 1 = Adjustable detection value 2 = Adjustable: Asymmetry, phase loss, phase rotation Special versions 0 = No fault memory 1 = Fault memory Options 0 = No delay time 1 = Two selectable delay times 2 = Adjustable delay times Contact circuit 0 = CO (npdt) 3 = NO (npst-no) 6
7 Technical data Insulation Insulation according to EN insulation rated voltage V 250 rated impulse withstand voltage kv 4 pollution degree 3 over-voltage category III Dielectric strength (A1, A2, A3, B1, B2), and V AC 2,500 contact terminals (11, 12, 14) and terminals (Z1, Z2) kv (1.2/50 μs) 6 Dielectric strength at open contact V AC 1,000 EMC specifications Type of test Reference Standard Electrostatic discharge contact discharge EN kv air discharge EN kv Radio-frequency electromagnetic field (80 1,000)MHz EN V/m Fast transients (burst) (5-50 ns, 5 khz) on (A1, A2, A3, R1, R2) and ( Z1, Z2) EN kv Surges (1.2/50 μs) on (A1, A2, A3, B1, B2) and (Z1, Z2) common mode EN kv differential mode EN kv Radio-frequency common mode ( MHz) to A1 - A2 EN V Radiated and conducted emission EN class B Other data Voltage and current values at terminals Z1 Z2 Type Link for time range V / ma 230 V / Type 71.91, PTC temperature measurement V / ma 24 V / 2.4 Maximum length of wiring to the Supply terminals/ Type 71.11, Contact bridge for time range m 150 / Measuring terminals Type Voltage measurement m 150 / 50 Type Current measurement m 150 / 50 (Wiring capacitance no greater than 10 nf/100 m) Type 71.91, PTC temperature measurement m 50 / 50 Measuring principle Type 71.11, 71.31, 71.41, 71.51, The measured value is the arithmetical average of 500 individual 71.91, measurements taken over a 100 ms period. Interruptions less than <200 ms are ignored. Safety logic Type 71.11, 71.31, 71.41, 71.51, Positive safety logic - When the value being monitored lies within the 71.91, acceptable area, the make contact is closed. Reaction time (following the application Type 71.11, 71.31, 71.41, 71.51, 0.5 s of the supply voltage) 71.91, Power lost to the environment without contact load W 4 with rated current W 5 Permitted storage temperature range C Protection category IP 20 Screw torque Nm 0.8 Max. wire size solid cable standed cable mm (2 x 2.5) (2 x 1.5) AWG 20 (2 x 14) (2 x 16) 7
8 Functions Monitoring relay Types Times Supply voltage Module width Contact conf. 1-phase 230 V, Under/Overvoltage 3-phase 400 V, Under/Overvoltage 3-phase 400 V, Phase/Symmetry 3-phase 400 V, Phase loss 3-phase 400 V, Phase DC voltage ( )V Under and Over voltage monitoring AC voltage ( )V Under and Over voltage monitoring DC current ( )A Under and Over current monitoring AC current ( )A (for to 600 A with current transformers) Under and Over current monitoring Thermistor relay (PTC) Adjustable Fault memory for and Delay time 5/10 min Delay time ( )s adjustable Power-up activation time delay ( )s starting inrush current suppression 24 V AC/DC 230 V AC 400 V AC 35 mm wide 22.5 mm wide Relay contact, 250 V AC/10A CO SPDT CO SPDT CO SPDT CO SPDT CO SPDT CO SPDT CO SPDT NO SPST-NO NO SPST-NO CO DPDT CO DPDT Current transformer Source as required 8
9 Explanation of relay marking and LED/LCD display Monitoring relay without LCD-dispaly ON LED green steady light: supply voltage is on and measuring system is active. DEF Default: the detected value is outside of the acceptable range (asymmetric is shown by the LED ASY). LED red flashing: delay time is running, see the function diagram. LED red steady light: output relay is off, contact (6-2) is open. ASY Phase asymmtery is outside of the predefined range. LED steady light: output relay is turned off, contact (6-2) is open. LEVEL Selected range as % value. TIME Delay time min (minutes) or s (seconds). MEMORY ON Fault memory switched on: the state of the output relay after the accurrence of a fault contact (6-2) open will be maintained, monitored value returns to within acceptable limits. Fault reset is made by switch manipulation from ON to OFF to ON, or by power down ( & x.xxx.0001), or by operating of the RESET (71.92.x.xxx.0001). MEMORY OFF Fault memory turned off: the sate of the output contatcts will only remain in the fault condition contact (6-2) open while the monitored value is outside of the acceptable limits. When the monitored value returns within the acceptable limits the contact will revert to the energised state. Monitored equipment will start again automatically. Monitoring relay with LCD-display SET/RESET Relay and Sets and resets the programmable values - see operating in the packing. SELECT Relay and Selects the desired parameter for programming - see operating instructions. DEF Default, LED red steady or flashing. PROG Modus Enter the programming mode by simultaneously pressing the buttons SET/RESET and SELECT for 3 seconds. The word prog is shown for 1 second. SELECT allows the choise of AC or DC, and is confirmed with SET/RESET. Successively pressing the button SELECT brings up the choises of Up, or Up Lo. The appropriate choise is made by pressing the SET/RESET button. The next step will program the appropriate values and the selection of the fault memory function (which is selected with a YES or NO ). If all programming steps are completed the display will read end. Short programmin After repeatedly pressing the SET/RESET button the measured value will be displayed, or 0 appears if nothing is instruction connected to Z1 and Z2 (5 and 9). If the programming is brocken off before end is shown in the display the previous program will remain unchanged after an interruption of the supply voltage. Program query Pushing the SELECT button for at least 1 second, enters the program inquiry mode. The programmed mode and the values are shown on the repeated pressing of the SELECT button. Flashing M (memory) Fault memory has had effect (fault acknowledgement and reset is made by a 1 second press of the SET/RESET button). LCD-display V = volt Level= value t 1 = T 1 - time during which short-time A = amp Hys = hysteresis fulctuations are not taken into account Up = upper limit (with hysteresis in down direction) M = memory (fault) t 2 = T 2 - (monitoring relay 71.51) the time Lo = lower limit (with hysteresis in up direction) Yes = yes - with memory during which inrush currents are not Up Lo = upper and lower limit - range detecting no = no - without memory taken into a account 9
10 LED/LCD status announcement/advice Type Starting mode Abnormal mode Reset Memory OFF After connecting T = 5 or 10 min open Time T runs Set point is immaterial Will close after T, if set point is OK Time T runs, Memory ON Time T runs, Will not close at RESET Will close at RESET Supply voltage to A1(1) and / or A2(5) is missing, Will close if supply voltage restored and set point OK Incorrect phase rotation or phase failure or voltage A1(1) and/ot A2(5) is > 1.11 U N Phase asymmetry Memory OFF Time T runs, Memory ON Time T runs, M in the display flashes Will not close at RESET M in the display - static Will close at RESET Memory OFF Time T2 runs, Set point immaterial Time T runs, Memory ON x.xxx.0300 Time T2 runs, Set point immaterial Time T runs, Temperature to high or PTC line break or PTC short circuit M in the display flashes Will not close at RESET M in the display - static Will close at RESET x.xxx.0001 Memory OFF Temperature to high or PTC line break or PTC short circuit x.xxx.0001 Memory ON Temperature to high or PTC line break or PTC short circuit Temperature is OK Will close at RESET 10
11 Functions Type Fixed limits Immediately if monitored value is outside of the set points. Switch on After expiry of the time T and if monitored value is within the set points. (6-2) closed. Type Switch OFF Immediately if monitored value is outside of the set points. Switch on After expiry of the time T and if monitored value is within the set points. (6-2) closed, all values within the set points. Type Immediately if monitored value is outside of the set points. Switch on After expiry of the time T and if monitored value is within the set points. (6-2) closed. Type If monitored value is outside of the set points and time T has elapsed. MEMOIRE ON MEMOIRE OFF *RESET MEMORY = By power-down or switch manipulation from ON to OFF to ON Switch on - MEMORY OFF Immediately monitored value returns within limits (off-set by 1% hysteresis). Switch on - MEMORY ON As above, but subject to the RESET operation having been actioned. RESET By Memory switch manipulation from ON to OFF and back to ON, or power down. (6-2) closed. 11
12 Functions L1 L2 L3 Type A1 A2 A ~U ASY U= 400 V AC 3~ (50/60 Hz ) Phase asymmetry Incorrect phase rotation Phase loss LED ASY yellow Phase asymmetry LED DEF red Voltage to A1 (1) and/or A2 (5) > 1.11 U N LED ON green Monitoring system is active and 400 V supply voltage is connected to 1-5 or A1-A2. (6-2) closed. Type Programmable U Lo mode If the monitored value is less than the lowerlimit and, time T has expired. MEMOIRE ON MEMOIRE OFF U Lo...U Lo + Hys U Up...U Up Hys U Up...U Lo *RESET MEMORY = Pressing SET/RESET > 1 s U Up mode If the monitored value is higher than the upper limit, and time T has expired. U Lo U Up mode If the monitored value of voltage is outside of the upper or lower voltage limits, and time T has expired. Voltage dips < T do not result in output relay switching off. Switch on U Lo or U Up modes When passing the hysteresis value. U Lo U Up mode When passing the U Lo or U Up value. RESET MEMORY Pressing SET/RESET > 1 sec. (6-2) closed. 12
13 Functions Type Programmable I Lo mode If the monitored value is less than the lowerlimit and, time T1 has expired. MEMOIRE ON MEMOIRE OFF I Lo...I Lo + Hys I Up...I Up Hys I Up...I Lo *RESET MEMORY = Pressing SET/RESET > 1 s I Up mode If the monitored value is higher than the upper limit, and time T1 has expired. I Lo I Up mode If the monitored value of voltage is outside of the upper or lower limits, and time T1 has expired. Inrush current < T2 is ignored Current dips < T1 do not result in output relay switching off. Switch on I Lo or I Up modes When passing the hysteresis value. I Lo I Up mode When passing the I Lo or I Up value. RESET MEMORY Pushing SET/RESET > 1 sec. (6-2) closed. Type x.xxx Thermistor line break - Over temperature R PTC > ( )kΩ, - Thermistor line short circuit (R PTC < 20Ω) - Loss of supply *PTC-Break **PTC-Short circuit Switch on Temperature within limits R PTC > ( )kΩ on power-up. ( )kΩ on cooling. Closed when temperature within limits. 13
14 Functions Type x.xxx Thermistor line break - Over temperature R PTC > ( )kΩ, - Thermistor line short circuit (R PTC < 20Ω) - Loss of supply MEMOIRE ON MEMOIRE OFF *PTC-Break **PTC-Short circuit *** RESET MEMORY = Operate the RESET key, or interrupt the supply. Switch on Temperature within limits (20Ω...2.5kΩ) on power-up. R PTC > ( )kΩ on cooling. Select MEMORY OFF If monitored value is expected to cross the resetting threshold. Select MEMORY ON If monitored value is expected to remain within limits. RESET MEMORY Operate the RESET key, or interrupt the supply. (21-24) Closed when temperature within limits. Normally closed (21-22) Closed when temperature outside limits / Power off. 14
Single-phase (220...240 V) voltage monitoring: Undervoltage Overvoltage Window mode (overvoltage + undervoltage) Voltage fault memory selectable
Features 70.11 70.31 70.41 Electronic voltage monitoring relays for single and three-phase applications Multifunctional types, providing the flexibility of monitoring Undervoltage, Overvoltage, Window
38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 A
38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 A Common features Instant ejection of relay by plastic retaining clip Integral coil indication and protection circuit EMR Electromechanical Relays
38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 - 16 A
38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 - 16 A 38 SERIES Common features Instant ejection of relay by plastic retaining clip Integral coil indication and protection circuit EMR Electromechanical
38 SERIES. Relay interface modules 0.1-2 - 3-5 - 6-8 - 16 A. EMR Electromechanical Relays. Common features. SSR Solid State Relays. 6.
38 Relay interface modules 0.1-2 - 3-5 - 6-8 - 16 A 38 Common features Instant ejection of relay by plastic retaining clip Integral coil indication and protection circuit 6.2 mm wide EMR - DC, AC or AC/DC
80 Series - Modular timers 16 A. Features 80.01 80.11
80 Series - Modular timers 16 A Features 80.11 Multi-function and mono-function timer range - Multi-function & multi-voltage 80.11 - On-delay, multi-voltage 17.5 mm wide Six time scales from 0.1s to 24h
48.12. 2 pole, 8 A Safety relay. Screw terminal. 35 mm rail (EN 60715) mounting. 2 CO (DPDT) 8/15 250/400 2,000 500 0.37 8/0.65/0.
48 Series - Relay interface modules 8 A Features 48.12 2 Pole Safety relay interface modules, 15.8 mm wide 48.12-2 Pole 8 A (screw terminal) DC sensitive coils Relay with forcibly guided contacts according
MasterINTERFACE 39 Series - Relay interface modules
MasterINTERFACE 39 Series - Relay interface modules Common features Space saving 6.2 mm wide Connections for 16-way jumper link Integral coil indication and protection circuit Secure retention and easy
MasterINTERFACE 39 Series - Relay interface modules
MasterINTERFACE 39 Series - 39 Common features Space saving 6.2 mm wide Connections for 16-way jumper link Integral coil indication and protection circuit Secure retention and easy ejection by plastic
80 Series - Modular timers 16 A. Features 80.01 80.11
80 Series - Modular timers 6 A 80. Multi-function and mono-function timer range - Multi-function & multi-voltage 80. - ON delay, multi-voltage 7.5 mm wide Six time scales from 0.s to 24h 35 mm rail (EN
34 Series - Slim electromechanical PCB relays 6 A. Features SERIES 34.51
34 Series - Slim electromechanical PCB relays 6 34 SERIES Features 34.51 Ultra-slim 1 Pole - 6 relay Printed circuit mount - direct or via PCB socket 35 mm rail mount - via screw, screwless or push-in
48 SERIES Relay interface modules 10 A
48 Relay interface modules 10 A 1 CO relay interface modules, mm wide Ideal interface for PLC and electronic systems Type 48.P3 1 CO 10 A s Type 48.31 1 CO 10 A s AC coils or DC sensitive coils Supply
49 Series - Relay interface modules 8-10 - 16 A. Features
Features 1 & 2 Pole relay interface modules 5 µm Gold plate contacts for low level switching capability 49.31-50x0-1 Pole 10 A (screw terminal) 49.52-50x0-2 Pole 8 A (screw terminal) 49.72-50x0-2 Pole
0.8 U N /0.5 U N 0.8 U N /0.5 U N 0.8 U N /0.5 U N 0.2 U N /0.1 U N 0.2 U N /0.1 U N 0.2 U N /0.1 U N
55 Series - General purpose relays 7-10 A Features 55.12 55.13 55.14 Printed circuit mount, general purpose 2, 3 & 4 Pole relays 55.12-2 Pole 10 A 55.13-3 Pole 10 A 55.14-4 Pole 7 A AC coils & DC coils
60 Series - General purpose relays 6-10 A. Features 60.12 60.13
Features 60.12 60.13 Plug-in mount 10 A General purpose relay 2 & 3 pole changeover contacts Cadmium Free contacts (preferred version) AC coils & DC coils UL Listing (certain relay/socket combinations)
93.68/93.69. Time scale: from 0.1s to 6h Multi-function For use with 34.51 (EMR) and 34.81 (SSR) relays. Screw terminal and push-in terminal
Series - Timed socket for 34 series Features.68/.69 Slim timed sockets for 34 series, 6.2 mm wide Timer adjustment via top mounted rotary knob accessible after assembly Control signal terminal DIP-switch
40 Series - Miniature PCB/Plug-in relays 8-10 - 16 A. Features 40.31 40.51 40.52
Features 40.31 40.51 40.52 1 & 2 Pole relay range 40.31-1 Pole 10 A (3.5 mm pin pitch) 40.51-1 Pole 10 A (5 mm pin pitch) 40.52-2 Pole 8 A (5 mm pin pitch) PCB mount - direct or via PCB socket 35 mm rail
1 pole, 16 A Screw terminal connection 35 mm rail (EN 60715) mounting. 2 pole, 8 A Screw terminal connection 35 mm rail (EN 60715) mounting
Series - Relay interface modules 8-10 - 16 A Features.01.02 1 & 2 pole relay interface modules, screw terminal socket, mm wide. Ideal interface for PL and electronic systems.01-1 Pole 16 A.02-2 Pole 8
13 SERIES. Electronic step relays 10-16 A 13.81 13.91
13 Electronic step relays 10-16 A 13 13.81 - Electronic step relay - Rail mount - 1 Pole 13.91 - Electronic step relay and timing step relay Switch box mount - 1 Pole Fixed time (10 minutes) timing function
Thermistor motor protection relays CM-MSS.22 and CM-MSS.23
Data sheet Thermistor motor protection relays CM-MSS.22 and CM-MSS.23 The thermistor motor protection relays CM-MSS.22 and CM-MSS.23 monitor the winding temperature of motors and protect them from overheating,
15 Series - Electronic step relay and dimmer. Features 15.91 15.51 15.81 SERIE
Series - Electronic step relay and dimmer SERIE Features.91.51.81 Electronic step relay and dimmer for control of lighting levels Suitable for incandescent and halogen lighting loads (with or without transformer
Single-phase (220...240 V) voltage monitoring: Undervoltage Overvoltage Window mode (overvoltage + undervoltage) Voltage fault memory selectable
70 Serie - Line monitoring relay 70 SRIS Feature 70.11 70.31 lectronic voltage monitoring relay for ingle and three-phae application Multifunctional type, providing the flexibility of monitoring Undervoltage,
Voltage monitoring relays CM-ESS.M For single-phase AC/DC voltages
Data sheet Voltage monitoring relays CM-ESS.M For single-phase AC/DC voltages The CM-ESS.M is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of
Electronic timer CT-AHD.12 OFF-delayed with 1 c/o (SPDT) contact
Data sheet Electronic timer CT-AHD.12 OFF-delayed with 1 c/o (SPDT) contact The CT-AHD.12 is an electronic time relay with OFF-delay. It is from the CT-D range. With their MDRC profile and a width of only
Three-phase monitoring relay CM-PFE
Data sheet Three-phase monitoring relay CM-PFE The CM-PFE is a three-phase monitoring relay that monitors the phase parameter phase sequence and phase failure in three-phase mains. 2CDC 251 005 S0012 Characteristics
Temperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection)
Data sheet Temperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection) The temperature monitoring relays CM-TCS monitor overtemperature,
12 Series - Time switches 16 A. Features 12.01 12.11 12.31
Mechanical time switches - daily time setting Type 12.01-1 Pole 16 A CO (SPDT) Type 12.11-1 Pole 16 A O (SPST-O) 17.6 mm width Type 12.31-0000 - 1 Pole 16 A CO (SPDT) Type 12.31-0007 - 1 Pole 16 A CO (SPDT)
Electronic timer CT-VBS.17+18 OFF-delayed without auxiliary voltage, for DC contactors Data sheet
Characteristics Single-function OFF-delay timer for DC contactors, without auxiliary voltage Width.5 mm CDC 5 6 F3 Approvals A culus E CCC CT-VBS a Circuit diagram b Marker label Marks a CE b C-Tick Order
Thermistor motor protection
Thermistor motor protection CM-E Range Thermistor motor protection Thermistor motor protection relays Benefits and advantages Selection table Operating principle and fields of application for thermistor
Bulletin 150 Smart Motor Controllers SMC-3 Smart Motor Controller
Overview/Modes of Operation Bulletin 150 Smart Motor Controller The SMC-3 is a compact, simple to use, solid-state motor controller designed to operate 3-phase motors. It features a built-in overload relay
Safety technique. Emergency stop module BO 5988 safemaster
Safety technique Emergency stop module BO 5988 safemaster 0221562 Function diagram Pushbutton on Mains or emergencystop () K1 According to EC Directive for machines 98/37/EG According to IEC/E 60204-1
RM17TE 183...528 V AC. Main. Product or component type. Product specific application. Relay monitored parameters 250 V DC 5 A DC
Characteristics multifunction control relay RM17-TE - range 183..528 V AC Complementary Reset time Maximum switching voltage Minimum switching current Maximum switching current [Us] rated supply voltage
ABB 1 NEW. Three-phase monitoring relay for grid feeding CM-UFS.1. Data sheet. Features. Approvals. Marks. Order data. Order data - Accessories
2CDC 251 014 F0t09 Features Monitoring of three-phase mains for grid feeding Type-tested in accordance with DIN V VDE V 0126-1-1: February 2006 Neutral conductor connection configurable Can also be used
Bulletin 150 SMC Flex Smart Motor Controller Specifications
Specifications Specifications Standard Features Optional Features Installation Setup Communications Power Wiring Control Wiring Keypad Software Starting and Stopping Modes Protection and Diagnostics Metering
VEO. V4PF480Y/277VSYTK02 Art.Nr.: 2104200. V4PF480Y/277VSYTK02P Art.Nr.: 2104210 TECHNICAL DATA
Monitoring of phase sequence and phase loss Monitoring of asymmetry Temperature monitoring (PTC) Supply voltage 208-480 V AC Supply circuit = measuring circuit 2 change-over contacts Width 45 mm Control
Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages
Data sheet Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages The CM-ESS.2 is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of
ABB 1. Three-phase monitoring relay CM-PFS. Data sheet. Features. Approvals. Marks. Order data. Order data - Accessories. Application.
1SR 430 824 F9300 Features Monitoring of three-phase mains for phase sequence and failure Powered by the measuring circuit 2 c/o (SPDT) contacts 1 LED for status indication Approvals R: yellow LED - relay
RM35UA13MW. range 15..600 V. Main. Product or component type. Relay monitored parameters
Characteristics multifunction voltage control relay RM35-U - range 15..600 V Complementary Reset time Maximum switching voltage [Us] rated supply voltage Supply voltage limits Power consumption in W Main
Power Supply Unit, Primary Switched, Narrow Design MINI-PS-12-24DC/24DC/1
Power Supply Unit, Primary Switched, Narrow Design MINI POWER provides: Extra narrow design with widths of 22.5 mm, 45 mm, and 67.5 mm (0.886, 1.772, and 2.657 in.) Global use due to a wide-range input
Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages
Data sheet Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages The CM-ESS.2 is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of
DEK-REL- 24/1/SEN. Extract from the online catalog. Order No.: 2964050
Extract from the online catalog DEK-REL- 24/1/SEN Order No.: 2964050 Relay terminal block for sensor, with soldered-in miniature relays, contact (AgNi+Au): small to medium loads, 1 N/O contact, input voltage
Panel Meters and Controllers Modular Panel Meter Type EDM 35
Panel Meters and Controllers Modular Panel Meter Type EDM 35 Modular digital panel meter, 3 1/2-digit Indicating or controlling current, voltage, resistance, temperature, tacho or frequency. Easy programming
MULTIFUNCTION TIME RELAY CRM-93H
4 MULTIFUNCTION TIME RELAY CRM-93H - 10 functions Features: Universal supply voltage AC/DC 12-240V 10 functions: - 5 time functions controlled by supply voltage - 4 time functions controlled by control
Relés e Contatores de Estado Sólido SIRIUS
Relés e Contatores de Estado Sólido SIRIUS Coletânea de dados técnicos ( product data sheet ) Agosto/212 SSR - 3RF21 22,5 mm Ponto Zero SSR - 3RF2 45 mm Ponto Zero SSR - 3RF22 45 mm Ponto Zero Trifásico
Technical Manual Functional Description for S800-RSU-H / S800W-RSU 2CCC413022M0205. 8201 Schaffhausen 1 / 10
ABB ABB Schweiz AG Technical Manual Functional Description for S800-RSU-H / S800W-RSU 2CCC413022M0205 09.04.2014 Page: 8201 Schaffhausen 1 / 10 Please use also the assembly instruction S800-RSU-H Remote
Type: EASY719 DC RC Article No.: 274119. Ordering information Relay outputs Quantity 6 Power supply V DC 24 V DC. Description
Type: EASY719 DC RC Article.: 274119 Ordering information Relay outputs Quantity 6 Power supply V DC 24 V DC Description 12 digital inputs (4 inputs available as analog inputs) 6 relay outputs LCD display
Analog signal converters CC-E I/I Current / current isolators
ata sheet Analog signal converters CC-E I/I Current / current isolators The CC-E I/I is an isolator for the electrical isolation of current signals without auxiliary supply. It allows the isolation between
LED Driver Compact dimming. Udriver LCAI 100W 900mA 1750mA ECO SR ECO series
Udriver LCAI 100W 900mA 1750mA ECO SR ECO series Product description Independent dimmable LED Driver Constant current LED Driver Output current adjustable between 900 1,750 ma Max. output power 100 W Suitable
Power Supply, Primary Switch Mode, Narrow Design MINI-PS-100-240AC/2x15DC/1
Power Supply, Primary Switch Mode, Narrow Design -PS-100-240AC/2x15DC/1 POWER provides: Extra narrow widths of 22.5 and 45 mm (0.886 and 1.772 in.) Global use due to a wide range input A high level of
Grid feeding monitoring according to VDE-AR-N 4105 and BDEW CM-UFD.M31
Data sheet Grid feeding monitoring according to VDE-AR-N 4105 and BDEW CM-UFD.M31 The CM-UFD.M31 is a multifunctional grid feeding monitoring relay. It provides different monitoring functions in accordance
Trip circuit supervision relay. Type RXTCS
Trip circuit supervision relay Type RXTCS ABB a global technology leader ABB is a global leader in Power and Automation technologies that enable utility and industry customers to improve performance while
ABB i-bus KNX Switch Actuator, x-fold, 16/20 A, MDRC SA/S x.16.6.1, 2CDG 110 1xx R0011
, 2CDG 110 1xx R0011 SA/S 8.16.6.1 2CDC 071 006 S0010 The 16/20 A Switch actuators are modular installation devices in Pro M Design for installation in the distribution board. The devices are especially
WD-AMX Water Detection Controllers
Page 1 of 5 WD-AMX Water Detection Controllers Features: Benefit: LED Status of leak status VFC output Audible alarm Auto or manual reset alarm output Uses an isolated AC signal which prevents oxidation
Electronic overload relay EF19 and EF45
Data sheet Electronic overload relay EF19 and EF45 Electronic overload relays offer reliable protection in case of overload and phase-failure. They are the alternative to thermal overload relays. Motor
Three-phase monitoring relays CM-PSS CM-PSS.31 and CM-PSS.41
Data sheet Three-phase monitoring relays CM-PSS CM-PSS.31 and CM-PSS.41 The three-phase monitoring relays CM-PSS.x1 monitor the phase parameters phase sequence, phase failure as well as over- and undervoltage.
Easy Multifunctional Safe
EMS Electronic motor starters www.eaton.eu Easy Multifunctional Safe EMS Multifaceted Performance with only 0 mm Eaton Moeller series products have always embodied quality and reliability in the machine
of the LED control gear Compact dimming Uconverter LCAI 55W 900mA 1750mA ECO SR ECO series
Uconverter LCAI 55W 900mA 1750mA ECO SR ECO series Product description Independent dimmable LED control gear Constant current LED control gear Output current adjustable between 900 1,750 ma Max. output
E-STOP relays, safety gate monitors
Unit features Safety features Gertebild ][Bildunterschrift_NOT_Sch.tuer_Licht Safety relay for monitoring E-STOP pushbuttons, safety gates and light beam devices Approvals Gertemerkmale Positive-guided
Telephone- and leased line modem for industrial applications TD-36
Telephone- and leased line modem for industrial applications TD-36 Modem for industrial PSTN- and leased line applications The TD-36 is an analogue V.34 PSTN modem as well as an industrial 2-wire leased
RM4TG20 three-phase network control relay RM4-T - range 200..500 V
Characteristics three-phase network control relay RM4-T - range 200..500 V Complementary [Us] rated supply voltage Output contacts Setting accuracy of time delay Delay at power up Measuring cycle Marking
Power Supply, Primary Switch Mode, Narrow Design MINI-PS-100-240AC/24DC/2
Power Supply, Primary Switch Mode, Narrow Design -PS-100-240AC/24/2 POWER provides: Extra narrow widths of 22.5 and 45 mm (0.886 and 1.772 in.) Global use due to a wide range input A high level of operational
Energy Management Energy Meter Type EM23 DIN
Energy Management Energy Meter Type EM23 DIN Class 1 (kwh) according to EN62053-21 Class B (kwh) according to EN50470-3 Class 2 (kvarh) according to EN62053-23 Accuracy ±0.5 RDG (current/voltage) Energy
Rack mounted telephone- and leased line modem for industrial applications
Rack mounted telephone- and leased line modem for industrial applications TR-6 Rack modem for industrial PSTNand /-wire leased line applications The TR-6 is an analogue V. 9 -rack PSTN modem as well as
Electronic overload relay EF65, EF96 and EF146
Data sheet Electronic overload relay EF65, EF96 and EF146 Electronic overload relays offer reliable protection in case of overload and phase-failure. They are the alternative to thermal overload relays.
PD30ETB20xxIS. Photoelectrics, Background Suppression reflective with IR light. Main features. Description
Photoelectrics, Background Suppression reflective with IR light Main features Description The PD30ET... stainless steel sensors are built with high-quality materials and designed for harsh environments.
MONITORING RELAYS. w VOLTAGE MONITORING RELAY UR5U1011. w SCHRACK-INFO. w TECHNICAL DATA
w VOLTAGE MONITORING RELAY UR5U1011 w SCHRACK-INFO AC/DC voltage monitoring in 1-phase mains Undervoltage monitoring 1 change over contact Width 17.5 mm Installation design w TECHNICAL DATA 502 1. Functions
DALI RC BASIC SO. Control unit Operating instructions
DALI RC BASIC SO Control unit Operating instructions Contents Safety... 4 General instructions 4 Safety instructions 4 Description... 5 Purpose and application 5 Function 5 Light control 5 Brightness
Switch Actuator, 8-fold, 10 A, MDRC AT/S 8.10.1, GH Q631 0075 R0111
, GH Q631 0075 R0111 The 8-fold switch actuator is a DIN rail mounted device for insertion in the distribution board. It is connected to the EIB via a bus terminal. In the event of bus voltage failure,
Features. Display. Measurements. Intelligent. Accuracy. Models. Installation DEIF A/S. Multi-instrument 4921210109D
7000/7000C/7020 Multi-instrument 4921210109D Features Measurements All 3-phase AC measurements True RMS Replaces analogue meters Demand on each phase current Accuracy U, I and F class 0.5 Other values
is then retained absolutely without interruption.
Page 1 of 11 DC UPS uninterruptible power supplies - DC UPS module 15 A Compact design, only 50 mm wide Absolutely interruption-free buffering of power failures through immediate electronic connection
Chrome DIN Rail Power Supply 24V 30W 1 Phase (Class II & NEC Class 2) / DRC-24V30W1AZ
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage without power de-rating Efficiency > 87.0% @ 115Vac & 230Vac NEC Class 2 / Limited
Quick Connect. quick - simple - efficient. www.g-mw.de
Quick Connect quick - simple - efficient www.g-mw.de Phone: +49 9103 7129-0 Fax: +49 9103 7129-207 Innovative connection technology to plug three single-phase current transformers to multifunctional power
RY2 miniature industrial relays
6 RY2 Relays of general application For plug-in sockets, 35 mm rail mount acc. to PN-EN 60715 or on panel mounting Flat insert connectors - faston x 0,5 mm Recognitions, certifications, directives: RoHS,
RISH EM 3490 DS Dual Source Energy Meter RISH EM 3490 DS. Application : Product Features:
Application : RISH Master 3490 DS measures important electrical parameters of Utility (in normal mode) & Generators (in Power back up) in three phase and single phase Network & replaces the multiple analog
Electronic Pressure Switch EDS 3000
For Your Information Electronic Pressure Switch EDS 3000 User Manual Revision: November 01, 2002 1. EDS 3000 Functions The EDS 3000 unit offers the following functions: Display pressure in psi, MPa, or
Soft Starter. Product Description. Ordering Code. Type Selection. Selection Guide RSG D 40 16 E 0 VD00
Soft Starter Three Phase General Purpose Soft Starters Type RSGD Soft starting and soft-stopping of 3-phase squirrel cage motors 45mm wide IP20 housing Operational Voltage: RSGD40 (220-400V), RSGD60 (220-600V)
LINETRAXX VMD460-NA. Network and system protection (NS protection) for monitoring the power feed-in of power generation systems
LIETRAXX -A etwork and system protection (S protection) for monitoring the power feed-in of power generation systems TDB301021en/06.2013 LIETRAXX -A etwork and system protection (S protection) for monitoring
Safety automation solutions
Operating principle, characteristics Preventa safety s types XPS AV,, For and switch monitoring Operating principle Safety s XPS AV, and are used for monitoring circuits conforming to standards EN/ISO
MCR-VDC-UI-B-DC. Voltage Transducer for DC Voltages. INTERFACE Data Sheet 100260_en_01. 1 Description
Voltage Transducer for DC Voltages TERFACE Data Sheet 000_en_0 PHOENIX CONTACT - /00 Description The MCR voltage transducer measures DC voltages in several signal ranges from 0... ±0 V DC to 0... ±0 V
Vert-X 16-5V / 10...90% Ub. Applications Servodrives Dancer arm Operating table
Version MH-C MH-C2 Electrical data Measuring range 0... 360 - Indep. linearity % meas. range ±0.3 - Max. hysteresis 0.1 - Resolution bit 12 - Max. repeatability 0.1 - Sample rate fast mode khz (5) - Sample
Shutter Actuator Standard, 4-fold, 230 VAC, MDRC RA/S 4.230.1, GH Q631 0076 R0111. ABB i-bus EIB
, GH Q631 0076 R0111 2CDC 071 240 F0003 The Shutter Actuator Standard is used to control a maximum of four independent 230 VAC drives for positioning shutters, blinds, awnings and other hangings as well
RISH CON - Hz. Salient Features : Application : Product Features: FREQUENCY TRANSDUCER
Application : The RISH CON - Hz transducer is used for frequency measurement. The output signal is proportional to measured frequency and is either load independent DC Current or load independent DC Voltage.
ABB i-bus EIB / KNX Analogue Input AE/S 4.2
Product Manual ABB i-bus EIB / KNX Analogue Input AE/S 4.2 Intelligent Installation Systems This manual describes the functionality of Analogue Input AE/S 4.2. Subject to changes and errors excepted. Exclusion
Electronic Pressure Switch EDS 300
Electronic Pressure Switch EDS 300 User manual Page 2 of 16 Content 1. Functions of the EDS 300...3 2. Mounting...3 3. Operating keys on the membrane keypad...4 4. Digital display...4 5. Output function...5
Positive-guided relay outputs: 3 safety contacts (N/O), instantaneous. 1 auxiliary contact (N/C), instantaneous
Safety relay for monitoring E-STOP pushbuttons. Approvals Unit features Positive-guided relay outputs: 3 safety contacts (N/O), instantaneous 1 auxiliary contact (N/C), instantaneous Safe separation of
Current and voltage measuring relays
Current and voltage measuring relays RXIK 1, RXEEB 1 and Page 1 Issued June 1999 Changed since July 1998 Data subject to change without notice RXIK 1 RXEEB 1 (SE980082) (SE980081) (SE970869) Features Application
Series AMEPR30-AZ up to 2.5A AC-DC / DC-DC LED Driver / Converter
FEATURES: Click on Series name for product info on aimtec.com Models Single output Model Max Output Power (W) 1 AC-DC Constant Current or Constant Over temperature protection Voltage LED Driver Over current
3-phase, bidirectional energy meter
Data sheet www.sbc-support.com 3-phase, bidirectional energy meter with S0 pulse output Bidirectional energy meter with S0-interface. The S0 interface is a hardware interface for the transmission of measured
STEP-PS/1AC/12DC/1.5. Extract from the online catalog. Order No.: 2868567. DIN rail power supply unit 12 V DC/1.5 A, primary switched-mode, 1- phase
Extract from the online catalog STEP-PS/1AC/12DC/1.5 Order No.: 2868567 DIN rail power supply unit 12 V DC/1.5 A, primary switched-mode, 1- phase Commercial data EAN 4046356292924 Pack 1 pcs. Customs tariff
LC1D65AM7 TeSys D contactor - 3P(3 NO) - AC-3 - <= 440 V 65 A - 220 V AC coil
Product data sheet Characteristics LC1D65AM7 TeSys D contactor - 3P(3 NO) - AC-3 -
Chrome DIN Rail Power Supply 24V 91.2W 1 Phase (Class II & NEC Class 2) / DRC-24V100W1AZ
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage without power de-rating Efficiency > 87.0% @ 115Vac, > 89.0% @ 230Vac NEC Class
Product and functional description
Product and functional description The KNX / DALI gateway N 141/02 is a 4 MU wide, DINrail mounted KNX device with one DALI interface to which up to 64 DALI actuators (e.g. DALI ballasts) can be connected
Operating ambient temperature range: 5ºC to 50ºC Storage temperature range: -30ºC to 70ºC
HOJA TÉCNICA 1400H101 Edición 01 (02 de 08) www.ako.es GENERAL TECHNICAL SPECIFICATIONS Temperature range: -50ºC to +99ºC type: NTC Total accuracy ( + controller): ±1ºC lead extension with cable AKO-15586:
R.C.C.B. s two-pole LEXIC
87045 LIMOGES Cedex Telephone : (+33) 05 55 06 87 87 Fax : (+ 33) 05 55 06 88 88 R.C.C.B. s two-pole LEXIC 089 06/09/10/11/12/15/16/17/18/ 27/28/29/30/35, CONTENTS PAGES 1. Electrical and mechanical characteristics...
Chrome DIN Rail Power Supply 12V 54W 1 Phase (Class II & NEC Class 2) / DRC-12V60W1AG
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage and full power up to 55 C Power will not de-rate for the entire input voltage range
Installation and User Guide
Installation and User Guide 458-UNI8 8-Channel Universal Dimmer Module Introduction The 458/UNI8 is an 8-channel universal, digital transistor, dimmer module. Each channel s mode can be selected for either
Power Meter Series 700
PowerLogic power-monitoring units Power Meter Series 700 Technical data sheet 2007 Functions and characteristics E90463 The PowerLogic Power Meter Series 700 offers all the measurement capabilities required
7 - Phaseo power supplies and transformers
/0 Contents 0 - Phaseo power supplies and transformers Selection guide: Phaseo power supplies Modular, Optimum and universal ranges........................ page /2 Selection guide: Phaseo power supplies
Multifunctional three-phase monitoring relays CM-MPS CM-MPS.43
Data sheet Multifunctional three-phase monitoring relays CM-MPS CM-MPS.43 The three-phase monitoring relay CM-MPS.43 monitors the phase parameters phase sequence, phase failure, over- and undervoltage
TMS TANK MANAGEMENT SYSTEM
TMS TANK MANAGEMENT SYSTEM Page 1 of 9 Operating Instructions GENERAL The Tank Management System is a bespoke design to control, monitor and accommodate efficient storage and dispensing of TMS. FUNCTIONS
Waveguide Access Point WGA631. Product Guide
Waveguide Access Point Product Guide Waveguide Access Point Contents 1. Description............................ 3 2. Application............................ 3 3. Technical data... 4 4. Physical interfaces......................