BSX TM Freeze Protection or Process Temperature Maintenance BSX self-regulating heating cables are designed to provide freeze protection or process temperature maintenance to metallic and nonmetallic piping, tanks and equipment. The heat output of BSX cable varies in response to the surrounding conditions along the entire length of a circuit. Whenever the heat loss of the insulated pipe, tank or equipment increases (as ambient temperature drops), the heat output of the cable increases. Conversely, when the heat loss decreases (as the ambient temperature rises or product flows), the cable reacts by reducing its heat output. This self-regulating feature allows BSX to be overlapped without temperature upset damage to the cable. BSX cables are approved for use in ordinary (nonclassified) areas and are certified to the ATEX directive for use in Category and (Zone and ) classified areas. Available Watt densities...9, 5, 5, W/m at C Nominal supply voltage... 0 Vac Maximum maintenance temperature... 65 C Maximum continuous exposure temperature Power-off... 85 C Minimum installation temperature... C (OJ); -5 C (FOJ) Minimum bend radius... mm T-rating 9, 5, 5 W/m... T6 85 C W/m...T5 0 C Based on stabilised design... T6 85 C Basic Accessories... Nickel-Plated Copper Bus Wires (. mm ) Radiation Cross-Linked Semiconductive Heating Matrix Radiation Cross-Linked Dielectric Insulation Tinned Copper Braid 5 Polyolefin overjacket provides additional protection where exposure to aqueous inorganic chemicals is expected. Options... 5, 6 6 FOJ Fluoropolymer overjacket provides additional protection where exposure to organic chemicals or corrosives is expected. Power Connection: All BSX cables require a TBX-L power boot for terminating the circuit before connecting to power. End-of-Circuit Termination: All BSX cables require the use of the ET-6 end cap and ET-60 overcap for terminating at the end of the circuit.. Cable may be energised at other voltages; contact Thermon for design assistance.. T-rating per internationally recognised testing agency guidelines.. Thermon heating cables are approved for the listed T-ratings using the stabilised design method. This enables the cable to operate in hazardous areas without limiting thermostats. The T-rating may be determined using CompuTrace Electric Heat Tracing Design Software or contact Thermon for design assistance.. Information on additional accessories to complete a heater circuit installation and to comply with approval requirements can be found in the Self-Regulating Cables Systems Accessories product specification sheet (Form TEP00U). Boezemweg 5 6 KG Pijnacker PO Box 05 60 AE Pijnacker The Netherlands Phone: + (0) 5-6 5 70 Facsimile: + (0) 5-6 5 79 0 Thermon Dr. PO Box 609 Phone: + 5-96-580 Facsimile: + 5-96-67
BSX TM Power Output Curves... The power outputs shown apply to overjacketed cable installed on insulated metallic pipe at the service voltage stated below. Watts per Metre 0 5 0 5 0 5 5 0 Vac Nominal BSX 8- BSX 5- BSX - Certifications/Approvals... Power Output at C W/m BSX - 9 BSX 5-5 BSX 8-5 BSX - BSX - BSX at 0 Vac 0 0 0 0 0 50 60 65 Pipe Temperature C II G/D EEx e II T5 or T6 0 ATEX 0 Factory Mutual Research Underwriters Laboratories Inc. BSX has additional hazardous area approvals including: DNV Lloyd s SAA JIS CCE/CMRS Contact Thermon for additional approvals and specific information. Circuit Breaker Sizing and... Maximum circuit lengths for various circuit breaker amperages are shown below. Circuit breaker sizing and earth-fault protection should be based on applicable local codes. For information on design and performance on other voltages, contact Thermon. Earth-fault protection of equipment should be provided for each branch circuit supplying electric heating equipment. 0 Vac Service Voltage BSX - BSX 5- BSX 8- BSX - B Circuit Breakers Max. Circuit Length vs. Breaker Size Start-Up Metres emperature C 6 A 5 A A 9 6 6 0 9 6 6 56 6 6 7 99 6 7 8 8 0 7 8 8 98 5 8 80 5 60 9 6 6 0 9 6 6 7 6 6 6 95 67 5 0 0 58 9 7 5 7 9 7 58 75 T 0 Vac Service Voltage BSX - BSX 5- BSX 8- BSX - C Circuit Breakers Max. Circuit Length vs. Breaker Size Start-Up Metres emperature C 6 A 5 A A 9 6 6 0 9 6 6 56 6 6 7 99 6 7 8 8 0 7 8 8 98 5 8 80 5 60 9 6 6 0 9 6 6 78 6 6 0 8 77 0 0 0 75 7 0 59 9 8 8 75 96 T Note.... Maximum circuit lengths shown are based on an instantaneous trip current characteristic per IEC 60898 at the referenced start-up temperature and a C maintenance temperature. For maximum circuit lengths with other trip current characteristics contact Thermon.. While a heat tracing system is generally designed to keep the contents of a pipe at the desired maintain temperature, the cable may be energized at lower temperatures. For design data with lower start-up temperatures than represented above contact Thermon for design assistance.. The maximum circuit length is for one continuous length of cable, not the sum of segments of cable. Refer to CompuTrace design software or contact Thermon for current loading of segments. Form TEP0067U-00 Thermon Manufacturing Co. Printed in U.S.A. Information subject to change.
RSX TM 5- Freeze Protection or Process Temperature Maintenance RSX 5- self-regulating heating cable is designed for applications where the Watt density requirements preclude the use of the standard range of winterization cables. The cable is ideally suited for freeze protection or process temperature maintenance applications that have higher heat losses but are not exposed to high temperatures (such as steam cleaning). The ends of RSX 5- must be properly terminated prior to connecting the cable to power. Refer to the Self-Regulating Cables Systems Accessories product specification sheet (Form TEP00U). RSX 5- is approved for use in ordinary (nonclassified) areas and Zone and classified areas. Available Watt density... 8 W/m at C Nominal supply voltage... 0 Vac Maximum maintenance temperature... 65 C Maximum continuous exposure temperature Power-off... 85 C Minimum installation temperature... C (OJ); -5 C (FOJ) Minimum bend radius... mm T-rating...T5 0 C Power Output Curve... 60 55 5, 6 Nickel-Plated Copper Bus Wires (. mm ) Radiation Cross-Linked Semiconductive Heating Matrix Radiation Cross-Linked Dielectric Insulation Tinned Copper Braid (BC) Options... 5 OJ Polyolefin Overjacket 6 FOJ Fluoropolymer Overjacket Circuit Breaker Sizing... Watts per Metre 50 5 0 5 0 5 RSX 5-0 Vac Service Voltage Max. Circuit Length Start-Up vs. Breaker Size Temperature Metres (C- Breakers) C 6 A 5 A A 0 A 5 56 7 98 RSX 5-0 5 7 9 0 8 6 8 Certifications/Approvals... 0 Factory Mutual Research 5 0 0 0 0 50 60 65 Pipe Temperature C. Cable may be energised at other voltages; contact Thermon for design assistance.. T-rating per internationally recognised testing agency guidelines. RSX 5- has additional hazardous area approvals including: DNV Lloyd s SAA JIS CCE/CMRS Contact Thermon for additional approvals and specific information. Boezemweg 5 6 KG Pijnacker PO Box 05 60 AE Pijnacker The Netherlands Phone: + (0) 5-6 5 70 Facsimile: + (0) 5-6 5 79 0 Thermon Dr. PO Box 609 Phone: + 5-96-580 Facsimile: + 5-96-67 Form TEP008U-00 Thermon Manufacturing Co. Printed in U.S.A. Information subject to change.
KSX TM Process Temperature Maintenance or Freeze Protection High performance KSX self-regulating heating cables are designed specifically for high heat loss freeze protection applications or process temperature maintenance where steam cleaning is not required. The heat output of KSX cable varies in response to the surrounding temperature by reducing its thermal output with increasing temperature. KSX cables are approved for use in ordinary (nonclassified) areas and are certified to the ATEX directive for use in Category and (Zone and ) classified areas. Available watt densities... 8, 6 W/m @ C Nominal supply voltages...0 Vac Max. maintenance or exposure temperature Continuous power-on... C Minimum installation temperature... -60 C Minimum bend radius... mm T-rating... T 00 C Based on stabilised design... T to T6 Basic Accessories... Power Connection: All KSX cables require a TBX-L power connection boot for terminating the circuit before connecting to power. End-of-Circuit Termination: KSX cables require the ET-8 end cap and ET-80 overcap for terminating at the end of the circuit.. Cable may be energised at other voltages; contact Thermon for design assistance.. T-rating per internationally recognised testing agency guidelines.. Thermon heating cables are approved for the listed T-ratings using the stabilised design method. This enables the cable to operate in hazardous areas without limiting thermostats. The T-rating may be determined using CompuTrace Electric Heat Tracing Design Software or contact Thermon for design assistance.. Information on additional accessories to complete a heater circuit installation and to comply with approval requirements can be found in the Self-Regulating Cables Systems Accessories product specification sheet (Form TEP00U). Nickel-Plated Copper Bus Wires (. mm ) Semiconductive Heating Matrix and Fluoropolymer Dielectric Insulation Tinned Copper Braid Fluoropolymer overjacket provides additional protection to cable and braid where exposure to chemicals or corrosives is expected. Features... Withstands continuous flamibility testing according to IEC 60-: 99 Allows cable to be installed at temperatures to -60 C Termination for system tested for ozone stability, UV stability and flammability testing according to ISO/IEC requirements Boezemweg 5 6 KG Pijnacker PO Box 05 60 AE Pijnacker The Netherlands Phone: + (0) 5-6 5 70 Facsimile: + (0) 5-6 5 79 0 Thermon Dr. PO Box 609 Phone: + 5-96-580 Facsimile: + 5-96-67
KSX TM Power Output Curves... The power outputs shown apply to overjacketed cable installed on insulated metallic pipe at the service voltage stated below. Watts per Meter 70 60 50 0 0 0 0 0 Vac Nominal KSX 0- KSX 5- Power Output at C W/m KSX 5-8 KSX 0-6 KSX at 0 Vac 0 0 60 90 0 Pipe Temperature C Certifications/Approvals... II G/D EEx e II T 0 ATEX 0886 Factory Mutual Research Underwriters Laboratories Inc. Circuit Breaker Sizing and... Maximum circuit lengths for various circuit breaker amperages are shown below. Circuit breaker sizing and earthfault protection should be based on applicable local codes. For information on design and performance on other voltages, contact Thermon. Earth-fault protection of equipment should be provided for each branch circuit supplying electric heating equipment. B Circuit Breakers 0 Vac Service Voltage Max. Circuit Lengt h vs. Breaker Size Start-Up Metres Temperature C 6 A 5 A A 6 KSX 5- KSX 0-0 7 9 6 8 5 56 7 7 56 0 5 0 5 6 7 C Circuit Breakers 0 Vac Service Voltage Max. Circuit Lengt h vs. Breaker Size Start-Up Metres Temperature C 6 A 5 A A 6 KSX 5- KSX 0-0 6 6 7 6 59 78 0 6 59 78 6 59 78 5 56 7 Note.... Maximum circuit lengths shown are based on an instantaneous trip current characteristic per IEC 60898 at the referenced start-up temperature and a C maintenance temperature. For maximum circuit lengths with other trip current characteristics contact Thermon.. While a heat tracing system is generally designed to keep the contents of a pipe at the desired maintain temperature, the cable may be energized at lower temperatures. For design data with lower start-up temperatures than represented above contact Thermon for design assistance.. The maximum circuit length is for one continuous length of cable, not the sum of segments of cable. Refer to CompuTrace design software or contact Thermon for current loading of segments. KSX has additional hazardous area approvals including: DNV Lloyd s SAA JIS CCE/CMRS GGTN Contact Thermon for additional approvals and specific information. Form TEP007U-0 Thermon Manufacturing Co. Printed in U.S.A.
TSX TM Process Temperature Maintenance or Freeze Protection TSX self-regulating heating cables are designed specifically for process temperature maintenance or freeze protection where elevated cold-start currents are unacceptable. TSX withstands the temperature exposures associated with steam purging. The heat output of TSX cable varies in response to the surrounding temperature. Variations in the ambient temperature or heat lost through the thermal insulation are compensated for automatically along the entire length of a heat-traced pipe. This self-regulating feature allows TSX to be overlapped without temperature upset damage to the cable. TSX cables are approved for use in ordinary (nonclassified) areas and Zone and classified areas. 5 Available Watt densities... 9, 8, 7, 7 W/m at C Nominal supply voltage... 0 Vac Maximum maintenance temperature... C Maximum continuous exposure temperature Power-off... 90 C Minimum installation temperature... -5 C Minimum bend radius... mm T-rating...T 00 C Basic Accessories... Power Connection: All TSX cables require a TBX-L power boot for terminating the circuit before connecting to power. End-of-Circuit Termination: TSX cables with the metallic braid require the use of the ET-8 end cap for terminating at the end of the circuit. TSX cables with the overjacket option require the ET-6 end cap for terminating at the end of the circuit.. Cable may be energised at other voltages; contact Thermon for design assistance.. T-rating per internationally recognised testing agency guidelines.. Information on additional accessories to complete a heater circuit installation and to comply with approval requirements can be found in the Self-Regulating Cables Systems Accessories product specification sheet (Form TEP00U). Nickel-Plated Copper Bus Wires (. mm ) Semiconductive Heating Matrix Fluoropolymer Dielectric Insulation Nickel-Plated Copper Braid (BN) Options... 5 OJ Fluoropolymer overjacket over nickelplated copper braid provides additional protection to cable and braid where exposure to chemicals or corrosives is expected. Certifications/Approvals... Factory Mutual Research TSX has additional hazardous area approvals including: DNV Lloyd s SAA JIS CCE/CMRS Contact Thermon for additional approvals and specific information. Boezemweg 5 6 KG Pijnacker PO Box 05 60 AE Pijnacker The Netherlands Phone: + (0) 5-6 5 70 Facsimile: + (0) 5-6 5 79 0 Thermon Dr. PO Box 609 Phone: + 5-96-580 Facsimile: + 5-96-67
TSX TM Power Output Curves... The power outputs shown apply to overjacketed cable installed on insulated metallic pipe at the service voltage stated below. Watts per Metre 50 0 0 0 0 Vac Nominal Power Output at C W/m TSX - 9 TSX 6-8 TSX 9-7 TSX - 7 TSX - TSX 9- TSX 6- TSX - TSX at 0 Vac 0-5 0 5 50 75 0 5 Pipe Temperature C Circuit Breaker Sizing and... Maximum circuit lengths for various circuit breaker amperages are shown below. Circuit breaker sizing and earth-fault protection should be based on applicable local codes. TSX heating cables do not exhibit significant elevated cold-start currents; therefore, it is not necessary to adjust the circuit length based on expected minimum ambient start-up temperatures to C. For information on design and performance on other voltages, contact Thermon. Earth-fault protection of equipment should be provided for each branch circuit supplying electric heating equipment. 0 Vac Service Voltage Max. Circuit Length vs. Breaker Size Metres (C- Breakers) 6 A 5 A TSX - 7 7 TSX 6-5 TSX 9-8 5 TSX - 6 7 Form TEP0006U-00 Thermon Manufacturing Co. Printed in U.S.A. Information subject to change.
HTSX TM 5 and 0 Process Temperature Maintenance or Freeze Protection HTSX self-regulating heating cables are designed specifically for process temperature maintenance or freeze protection where high temperature exposure capability is required. HTSX withstands the temperature exposures associated with steam purging. The heat output of HTSX cable varies in response to the surrounding temperature. Variations in the ambient temperature or heat lost through the thermal insulation are compensated for automatically along the entire length of a heattraced pipe. HTSX cables are approved for use in ordinary (nonclassified) areas and are certified to the ATEX directive for use in Category and (Zone and ) classified areas. Available watt densities... 8, 6 W/m @ C Nominal supply voltages...0 Vac Max. maintenance temperature... C Max. exposure temperature Intermittent power-on... 9 C Continuous power-off... 9 C Minimum installation temperature... -60 C Minimum bend radius... mm T-rating... T 00 C Based on stabilised design... T to T6 Basic Accessories... Power Connection: All HTSX cables require a TBX-L power connection boot for terminating the circuit before connecting to power. End-of-Circuit Termination: HTSX cables require the ET-8 end cap and ET-80 overcap for terminating at the end of the circuit.. Cable may be energised at other voltages; contact Thermon for design assistance.. T-rating per internationally recognised testing agency guidelines.. Thermon heating cables are approved for the listed T-ratings using the stabilised design method. This enables the cable to operate in hazardous areas without limiting thermostats. The T-rating may be determined using CompuTrace Electric Heat Tracing Design Software or contact Thermon for design assistance.. Information on additional accessories to complete a heater circuit installation and to comply with approval requirements can be found in the Self-Regulating Cables Systems Accessories product specification sheet (Form TEP00U). Nickel-Plated Copper Bus Wires (. mm ) Semiconductive Heating Matrix and Fluoropolymer Dielectric Insulation Tinned Copper Braid Fluoropolymer overjacket provides additional protection to cable and braid where exposure to chemicals or corrosives is expected. Features... Withstands continuous flamibility testing according to IEC 60-: 99 Allows cable to be installed at temperatures to -60 C Termination for system tested for ozone stability, UV stability and flammability testing according to ISO/IEC requirements Boezemweg 5 6 KG Pijnacker PO Box 05 60 AE Pijnacker The Netherlands Phone: + (0) 5-6 5 70 Facsimile: + (0) 5-6 5 79 0 Thermon Dr. PO Box 609 Phone: + 5-96-580 Facsimile: + 5-96-67
HTSX TM 5 and 0 Power Output Curves... The power outputs shown apply to overjacketed cable installed on insulated metallic pipe at the service voltage stated below. Watts per Meter 70 60 50 0 0 0 0 0 Vac Nominal Power Output at C W/m HTSX 5-8 HTSX 0-6 HTSX 5- Certifications/Approvals... HTSX at 0 Vac HTSX 0-0 0 60 90 0 Pipe Temperature C II G/D EEx e II T 0 ATEX 00790 Factory Mutual Research Underwriters Laboratories Inc. Circuit Breaker Sizing and... Maximum circuit lengths for various circuit breaker amperages are shown below. Circuit breaker sizing and earthfault protection should be based on applicable local codes. For information on design and performance on other voltages, contact Thermon. Earth-fault protection of equipment should be provided for each branch circuit supplying electric heating equipment. B Circuit Breakers 0 Vac Service Voltage Max. Circuit Lengt h vs. Breaker Size Start-Up Metres Temperature C 6 A 5 A A 6 HTSX 5- HTSX 0-0 7 9 6 8 5 56 7 7 56 0 5 0 5 6 7 C Circuit Breakers 0 Vac Service Voltage Max. Circuit Lengt h vs. Breaker Size Start-Up Metres Temperature C 6 A 5 A A 6 HTSX 5- HTSX 0-0 6 6 7 6 59 78 0 6 59 78 6 59 78 5 56 7 Note.... Maximum circuit lengths shown are based on an instantaneous trip current characteristic per IEC 60898 at the referenced start-up temperature and a C maintenance temperature. For maximum circuit lengths with other trip current characteristics contact Thermon.. While a heat tracing system is generally designed to keep the contents of a pipe at the desired maintain temperature, the cable may be energized at lower temperatures. For design data with lower start-up temperatures than represented above contact Thermon for design assistance.. The maximum circuit length is for one continuous length of cable, not the sum of segments of cable. Refer to CompuTrace design software or contact Thermon for current loading of segments. HTSX 5 and 0 has additional hazardous area approvals including: DNV Lloyd s SAA JIS CCE/CMRS GGTN Contact Thermon for additional approvals and specific information. Form TEP007U-0 Thermon Manufacturing Co. Printed in U.S.A.
VSX TM Process Temperature Maintenance or Freeze Protection High performance VSX self-regulating heating cables are designed specifically for process temperature maintenance or freeze protection where high maintain temperatures or high temperature exposure is required. VSX withstands the temperature exposures associated with steam purging. The heat output of VSX cable varies in response to the surrounding temperature by reducing its thermal output with increasing temperature and can be overlapped without temperature upset damage to the cable. With its high selfregulating characteristic, VSX can be installed in hazardous areas requiring a T temperature class rating. VSX cables are approved for use in ordinary (nonclassified) areas and Zone and classified areas. Available Watt densities... 5,, 8, 6 W/m at C Nominal supply voltage... 0 Vac Maximum maintenance temperature... 9 C Maximum continuous exposure temperature Continuous power-off... 0 C Intermittent power-on... C Minimum installation temperature... -5 C Minimum bend radius... mm T-rating...T 00 C Basic Accessories... Power Connection: All VSX cables require a TBX-L power boot for terminating the circuit before connecting to power. End-of-Circuit Termination: All VSX cables require the use of the ET-6 end cap for terminating at the end of the circuit.. Cable may be energised at other voltages; contact Thermon for design assistance.. T-rating per internationally recognised testing agency guidelines. VSX 0 has a T (00 C) temperature rating per CENELEC.. Information on additional accessories to complete a heater circuit installation and to comply with approval requirements can be found in the Self-Regulating Cables Systems Accessories product specification sheet (Form TEP00U). Nickel-Plated Copper Bus Wires (. mm ) Semiconductive Heating Matrix and Fluoropolymer Dielectric Insulation Nickel-Plated Copper Braid Fluoropolymer Overjacket Certifications/Approvals... Factory Mutual Research VSX has additional hazardous area approvals including: DNV Lloyd s SAA JIS CCE/CMRS Contact Thermon for additional approvals and specific information. Boezemweg 5 6 KG Pijnacker PO Box 05 60 AE Pijnacker The Netherlands Phone: + (0) 5-6 5 70 Facsimile: + (0) 5-6 5 79 0 Thermon Dr. PO Box 609 Phone: + 5-96-580 Facsimile: + 5-96-67
VSX TM Power Output Curves... The power outputs shown apply to overjacketed cable installed on insulated metallic pipe at the service voltage stated below. Watts per Metre 70 60 50 0 0 0 0 Vac Nominal VSX 0- VSX 5- VSX at 0 Vac VSX - VSX 5-0 0 50 70 90 0 50 Pipe Temperature C Power Output at C W/m VSX 5-5 VSX - VSX 5-8 VSX 0-6 Circuit Breaker Sizing and... Maximum circuit lengths for various circuit breaker amperages are shown below. Circuit breaker sizing and earth-fault protection should be based on applicable local codes. For information on design and performance on other voltages, contact Thermon. Earth-fault protection of equipment should be provided for each branch circuit supplying electric heating equipment. 0 Vac Service Voltage Max. Circuit Length vs. Breaker Siz e Start-Up Metres (C- Breakers) Temperature C 6 A 5 A A 0 A 98 68 0 0 VSX 5-0 98 68 0 0 98 68 0 0 6 5 5 6 VSX - 0 6 5 5 6 59 99 7 6 7 77 VSX 5- VSX 0-0 7 67 89 5 56 7 98 0 5 7 9 0 8 6 8 Form TEP0008U-00 Thermon Manufacturing Co. Printed in U.S.A. Information subject to change.
HPT TM Power-Limiting Heating Cable Process Temperature Maintenance or Freeze Protection High performance HPT power-limiting heating cables are designed specifically for process temperature maintenance or freeze protection where high maintain temperatures or high temperature exposure is required. HPT withstands the temperature exposures associated with steam purging. A coiled resistor alloy heating element (patent pending) provides the power-limiting feature of HPT. This PTC (Positive Temperature Coefficient) characteristic decreases the cable s power output as the heat-traced product temperature increases and allows the cable to be overlapped during installation. The composite construction of the heating element and fibre substrate, plus an additional fibre cushion layer, provides an exceptionally durable high performance heating cable. 5 6 7 HPT cables are approved for use in ordinary (nonclassified) areas and Zone and classified areas. Available Watt densities..., 8,, 57 W/m at C Nominal supply voltage... 0 Vac Maximum maintenance temperature... 9 C Maximum continuous exposure temperature Power-off... 60 C Minimum installation temperature... -5 C Minimum bend radius... mm Basic Accessories... Power Connection: All HPT cables require a TBX-L power boot for terminating the circuit before connecting to power. End-of-Circuit Termination: HPT cables with exposure temperatures below 00 C require the use of the ET-8 end cap and TT-6 fluoropolymer tape strip for terminating at the end of the circuit. HPT cables with exposure temperatures between 00 C and 60 C require the HPEK-OJ end cap for terminating at the end of the circuit.. Higher maintenance temperatures and operating voltages may be possible; contact Thermon for design assistance.. Information on additional accessories to complete a heater circuit installation and to comply with approval requirements can be found in the Power-Limiting Cables Systems Accessories product specification sheet (Form TEP008U). Nickel-Plated Copper Bus Wires (. mm ) Composite Metal Alloy/Fibre Heater Bus Connection (not shown) Fibreglass Braid (not shown) 5 Fluoropolymer Dielectric Insulation 6 Nickel-Plated Copper Braid 7 Fluoropolymer Overjacket Certifications/Approvals... Factory Mutual Research HPT has additional hazardous area approvals including: DNV Lloyd s SAA JIS CCE/CMRS Contact Thermon for additional approvals and specific information. Boezemweg 5 6 KG Pijnacker PO Box 05 60 AE Pijnacker The Netherlands Phone: + (0) 5-6 5 70 Facsimile: + (0) 5-6 5 79 0 Thermon Dr. PO Box 609 Phone: + 5-96-580 Facsimile: + 5-96-67
HPT TM Power-Limiting Heating Cable Power Output Curves... The power outputs shown apply to overjacketed cable installed on insulated metallic pipe at the service voltage stated below. Watts per Metre 60 50 0 0 0 0 Vac Nominal HPT 0- HPT 5- Zone Length cm HPT at 0 Vac HPT - HPT 5- Power Output at ºC W/m HPT 5- HPT - 6 8 HPT 5-6 HPT 0-6 57 0 0 50 70 90 0 50 Pipe Temperature C Circuit Breaker Sizing and... Maximum circuit lengths for various circuit breaker amperages are shown below. Circuit breaker sizing and earth-fault protection should be based on applicable local codes. For information on design and performance on other voltages, contact Thermon. Earth-fault protection of equipment should be provided for each branch circuit supplying electric heating equipment. 0 Vac Service Voltage Max. Circuit Length vs. Breaker Siz e Start-Up Metres (C- Breakers) Temperature C 6 A 5 A A 0 A 57 8 8 8 HPT 5- HPT - HPT 5- HPT 0-0 8 8 8 8 0 8 8 8 99 99 99 0 0 99 99 99 8 99 99 8 6 6 0 79 7 6 6 7 8 56 6 6 98 8 0 59 8 55 88 8 Form TEP00U-00 Thermon Manufacturing Co. Printed in U.S.A. Information subject to change.
MIK TM Mineral Insulated Heating Cable Process Temperature Maintenance or Freeze Protection MIK high performance mineral insulated heating cables are used extensively for high temperature maintenance, high temperature exposure and/or high Watt density applications which exceed the limitations of thermoplastic insulated cables. Thermon s MIK mineral insulated cables are available in three outer sheath materials to meet the temperature and exposure requirements of the application. MIK cables are approved for use in ordinary (nonclassified) areas and are certified to the ATEX directive for use in Category and (Zone and ) classified areas. Rated voltages... 00 and 500 Vac Maximum maintenance temperature... 600 C Maximum continuous exposure temperature Power-off... 650 C Maximum Watt density... 00 W/m Minimum installation temperature... C Minimum bend radius... 6 x cable O.D. T-Rating 5... T to T6 (Using the principles of stabilized design or limiters) 6 Available MIK Sheaths... MIK Heater Sets... Metal Sheath Material MIC Copper MIN MIS Cupro Nickel Stainless Steel Maximum Exposure Temperature 80 C 50 C 650 C Thermon MIK cable sets are available in various factoryfabricated configurations designed for the cable type and number of conductors. Information regarding cable terminations is available from Thermon as part of a system design. Solid Alloy or Copper Conductor Compacted Magnesium Oxide Insulation Metallic Sheath Certification/Approval... II G EEx e II T to T6 II G EEx ed IIB or IIC T to T6 LCIE 0 ATEX 605 MIK has additional hazardous area approvals including: GGTN Kazakhstan. Specific voltage depends on circuit length and design conditions.. Watt density limitations are correlated to maintain temperatures.. Optional overjackets are available on MIC cables; contact Thermon.. When using cable terminations under the insulation the maximum allowable temperature is lower; contact Thermon. 5. T-rating per internationally recognised testing agency guidelines. 6. Thermon heating cables are approved for the listed T-ratings using the stabilised design method. This enables the cable to operate in hazardous areas without limiting thermostats. Contact Thermon for design assistance. Boezemweg 5 6 KG Pijnacker PO Box 05 60 AE Pijnacker The Netherlands Phone: + (0) 5-6 5 70 Facsimile: + (0) 5-6 5 79 0 Thermon Dr. PO Box 609 Phone: + 5-96-580 Facsimile: + 5-96-67
MIK TM Mineral Insulated Heating Cable Available Cables... 00 and 500 Vac One Conductor Cable Diameter mm Resistance Ohm/m at 0 C Cold Lead Cable Size mm MIN-M-600..600. 5 MIN-M-00..000. 5 MIN-M-60. 7 0.60. 5 MIN-M0. 0 0.00. 5 MIN-M-50. 0.50 6. 0 MIN-M-60. 9 0.60 6. 0 MIN-M-6. 0.06. 5 MIN-M. 0.00. 5 MIN-M-5. 7 0.05 6. 0 MIN-M-7. 6 0.07 6. 0 MIN-M-. 9 0.0 6. 0 MIN-M-7 5. 0.007. 0 MIN-M- 5. 9 0.00 6. 0 MIS-M-K..000. 5 MIS-M-600. 6.00. 5 MIS-M00..000. 5 MIS-M-500..500. 5 MIS-M-600. 6.600. 5 MIS-M-00. 9.000. 5 MIS-M-60. 0.60. 5 MIS-M0. 7 0.00. 5 MIS-M-50 5. 0.50 6. 0 MIS-M-60 6. 5 0.60 6. 0 Circuit Breaker Sizing and... Maximum circuit lengths for MIK heating cables will be a function of cable resistance, circuit length and operating voltage. Circuit length, breaker sizing and earth-fault protection should be based on applicable local codes. Earth-fault protection of equipment should be provided for each branch circuit supplying electric heating equipment. Reference Legend... Example: MIC-M-800 Sheath Material Conductor Resistance C... Copper Ω/km N... Cupro Nickel S... Stainless Steel Number of Conductors Rated Voltage L... 00 Vac M... 500 Vac Note.... All resistances shown are per length of cable at 0 C and are subject to a ±% manufacturing tolerance.. Copper sheath available on request; contact Thermon. Form TEP000U-0 Thermon Manufacturing Co. Printed in U.S.A. Information subject to change.
TESH TM Series Constant Watt Heating Cable Long Line Temperature Maintenance or Freeze Protection TESH series resistance constant Watt heating cables are used where circuit lengths exceed the limitations of parallel resistance heating cables. TESH withstands the temperature exposures associated with steam purging. The series circuitry of TESH provides consistent Watt-permetre power output along the entire length of the cable with no voltage drop. A glassceramic tape layer adds additional protection to the heating cable and a fluoropolymer overjacket provides chemical resistance while maintaining maximum flexibility. The construction of the cable meets the 7 Joule impact test per EN5009. 5 TESH cables are approved for use in ordinary (nonclassified) areas and Catagories and ATEX classified areas. Maximum Watt density...5 W/m Maximum supply voltage... 750 Vac Maximum continuous exposure temperature Power-off... 60 C Minimum installation temperature... -60 C Minimum bend radius... 5 x cable O.D. T-rating...T to T6 (using the principles of stabilized design or limiters) Stabilised Design... The Watt density limitation for TESH cables is directly related to the desired maintain temperature. Thermon is able to ensure the T-rating based on a stabilised design that enables series constant Watt heating cables to operate in hazardous areas without limiting thermostats. TESH cable output and T-rating are dependent upon supply voltage, cable resistance, temperature conditions as well as additional variables. Contact Thermon for design assistance. Heating Conductor Fluoropolymer Dielectric Insulation Glassceramic Tape Nickel-Plated Copper Braid (BN) 5 Fluoropolymer Overjacket Certification/Approval... II G/D EEx e IIC T to T6 LCIE 00 ATEX 60 X TESH has additional hazardous area approvals including: GGTN Kazakhstan Basic Accessories... Power Connection: TESH cables typically require nonheating terminations at each end of the circuit before connecting to power. Contact Thermon for complete information.. T-rating per internationally recognised testing agency guidelines.. Thermon heating cables are approved for the listed T-ratings using the stabilised design method. This enables the cable to operate in hazardous areas without limiting thermostats. The T-rating may be determined using CompuTrace Electric Heat Tracing Design Software or contact Thermon for design assistance. Features... Withstands continuous flamibility testing according to IEC 60-: 99 Allows cable to be installed at temperatures to -60 C Boezemweg 5 6 KG Pijnacker PO Box 05 60 AE Pijnacker The Netherlands Phone: + (0) 5-6 5 70 Facsimile: + (0) 5-6 5 79 0 Thermon Dr. PO Box 609 Phone: + 5-96-580 Facsimile: + 5-96-67
TESH TM Series Constant Watt Heating Cable Available Cables... Resistance Ohm/m at 0 C Conductor Size mm Max. Cable Length m (with 0 ma earthfault protection) Cable Diameter mm TESH.9 0.009 6.00 5 7. 0 TESH. 0.00.00 55 6. TESH 7 0.007.50 85 5. 5 TESH 0.0.79 77 5 5. TESH.7 0.07.50 05. 9 TESH 5 0.05.0 090. 7 TESH 7.8 0.07 8.00 75. 6 TESH 5 0.05. 55. 6 TESH.5 0.05.60 00. 9 TESH 50 0.050.0 5. 7 TESH 65 0.065 0.75 890. TESH 80 0.080. 90. TESH 0 0.0.50 05. 9 TESH 50 0.50.0 5. 6 TESH 00 0.00 0.75 605. TESH 0 0.0 0.9 0. 5 TESH 80 0.80 0.79 555. TESH 80 0.80 0.6 5. TESH 600 0.600 0.9 0. TESH 700 0.700 0. 55. TESH 8 0.8 0.6 780. TESH 00.000 0.9 0. TESH 0.0 0. 95. TESH 750.750 0.9 65. TESH 000.000 0.55 900. TESH 000.000 0. 95. TESH 8000 8.000 0. 55. 8 Circuit Breaker Sizing and... Maximum circuit lengths for TESH heating cables will be a function of cable resistance, circuit length and operating voltage. Circuit length, breaker sizing and earth-fault protection should be based on applicable local codes. Earth-fault protection of equipment should be provided for each branch circuit supplying electric heating equipment. Note.... Longer circuit lengths are possible based on earth-fault protection with higher earthfault ratings; contact Thermon. Form TEP0070U-0 Thermon Manufacturing Co. Printed in U.S.A. Information subject to change.