Innovation for energy management

Innovation for energy management Components and solutions for any commercial or industrial application METERING NHP Electrical Engineering Products Pty Ltd Sales 1300 NHP NHP Sales 0800 NHP NHP nhp.com.au nhp-nz.com

WE RE easy to do business with At NHP we re solely committed to serving the needs of our customers in the industrial electrical industry. From concept design through to installation and after sales service, we are confident we have the experience and expertise to exceed your expectations and ensure you get the best result for your project. How? By combining Partnerships, Agility, Knowledge and Scalability, NHP can offer 100% Australian owned service that forms the ultimate choice in our industry. Partnerships: When you choose NHP you gain a valuable industry partner. You gain access to an exclusive network of quality global suppliers who, together with NHP, can achieve an engineered solution for your industrial electrical application. A partnership with NHP promises to last, working together with you to offer complete trust, assurance and peace of mind. Agility: At NHP we understand your project needs and know that these needs can often change throughout the life cycle of a project. With a seamless combination of local and technical support backed by around the clock service and local stock, NHP has the agility to provide real time solutions where and when you need them. Knowledge: If your industrial electrical application demands a specialist team of trained project management, design and engineering professionals, then NHP is the ultimate choice, bringing together over 40 years of electrical industry experience and knowledge. Scalability: With all the scale of a large multi-national company, NHP maintain a premium level of customer service and attention to detail no matter how big or small your project. With over 900+ expert staff in over 50+ branch and regional locations, when you deal with NHP you receive all of this combined knowledge and expertise delivered by local people with with a local focus, backed by global suppliers. NHP ELECTRICAL ENGINEERING PRODUCTS PTY LTD Sales 1300 NHP NHP nhp.com.au

Contents page Introduction to Energy management components 4 Energy Efficiency Codes, Initiatives, Systems and Mechanisms 5 kwh Meters 7 kwh meter selection chart 8-9 Conto D1 10 EM11 DIN 11 Conto D2b 12 Conto D2 13 Conto D4 14 EM2172D 15 EM2172R 16 EM4 DIN 17 WM22 18 EM24 DIN 19 PMW250 20 Multi Function and Power Quality Analyser 21 Multi Function and Power Quality Analyser selection chart 22 Nemo D4L 24 Nemo D4L+ 25 Nemo72b 26 Nemo72L 27 EM26-96 28 WM14 29 Nemo96HD + Modules 30 PM500 32 PM1000 33 WM30 + Modules 34 WM40 + Modules 35 WM5 + Modules 37 PM5000 39 Branch Circuit Monitoring System 40 Software 41 Communications (Gateways + Convertors) 42 Powersoft 43 FTEnergy Metrix 45 VMUC 46 Sub.net. 47 CT s 48 Cage clamp terminals 50 CT Test blocks 51 3

Introduction to energy management Green levies, tighter operating margins and profits are a few economic drivers forcing operators to use more intelligent power management strategies. Real-time measurements of electrical parameters, such as voltage variations or distortions, can be transmitted via networks to operators, warning of breaches in threshold limits. Power quality information improves on-site efficiency and eases negotiation with utility companies and energy authorities. NHP supplies energy management systems that provide information for operators to identify consumption trends and take corrective actions. By analysing the power profile operators can also aggregate loads and negotiate more favourable terms with the utility company. Real time power consumption monitoring also allows a site manager to anticipate overload conditions that would, for example, trip a circuit breaker and cause costly downtime. Alarm thresholds can be set to warn managers if preset limits are reached. Armed with this system loading and status information, managers can organise remedial action in a timely manner. The NHP Sustainability Centre At NHP we are committed to understanding and minimising any adverse impacts our operations and our products have on the environment. Our very own Sustainability Centre is located adjacent to our existing National Manufacturing and Distribution Centre in Laverton, Melbourne. The centre demonstrates a variety of sustainable energy technologies including: Horizontal axis wind generators Photovoltaic solar modules Grid interactive solar systems Off-grid systems Dual axis tracker Energy Management & control systems This significant project ensures NHP are at the forefront of the sustainable industry direction and are a leader in providing alternative energy solutions for commercial and industrial applications. NHP s Sustainability Centre encourages the use of alternative energy solutions and demonstrates what is possible with sustainable energy technologies. 4

Energy efficiency codes, initiatives, systems and mechanisms: NABERS NABERS is a national rating system that measures the environmental performance of Australian buildings, tenancies and homes. NABERS measures the energy efficiency, water usage, waste management and indoor environment quality of a building or tenancy and its impact on the environment and its performance is rated on a 1-6 star scale. Building Code of Australia Section J Section J deals with energy efficiency requirements of the Building Code of Australia for class 2 to 9 BCA standard definition buildings. The main objective of the BCA Section J is to reduce the Green House Gas (GHG) emissions of a building by reducing the amount of energy it requires for its normal operation. Carbon Pricing Mechanism: The carbon pricing mechanism is an emissions trading scheme that puts a price on Australia s carbon pollution. It was introduced by the clean energy legislation and applies to Australia s biggest carbon emitters (called liable entities). Under the mechanism, liable entities must pay a price for the carbon emissions they produce each year. NGERS The National Greenhouse and Energy Reporting (NGERS) Scheme was introduced in 2007 to provide data and accounting in relation to greenhouse gas emissions and energy consumption and production. The scheme s legislated objectives are to: underpin the carbon price mechanism; inform policy-making and the Australian public; meet Australia s international reporting obligations; and provide a single national reporting framework for energy and emissions reporting. EEO Energy Efficiency Opportunities (EEO) is a mandatory Federal Government initiative requiring businesses using more than 0.5 petajoules of energy each year to assess and report opportunities that may improve the efficiency of their energy use. Green Star Green Star is a national, voluntary, holistic environmental rating system that evaluates the environmental design and construction of buildings and communities. Green Star rating tools help the property industry to reduce the environmental impact of buildings, improve occupant health and productivity and achieve real cost savings, while showcasing innovation in sustainable building practices. CBD Commercial Building Disclosure (CBD) is a national program designed to improve the energy efficiency of Australia s large office buildings. Under the Building Energy Efficiency Disclosure Act 2010, there are mandatory obligations applicable to many commercial buildings. Most sellers or lessors of office space of 2,000 square metres or more are required to obtain and disclose a current Building Energy Efficiency Certificate (BEEC). A BEEC is comprised of: a NABERS Energy star rating for the building; an assessment of tenancy lighting in the area of the building that is being sold or leased; and general energy efficiency guidance. NMI M6 As of the 1st January 2013 the exemption on meters used for sub-billing applications was lifted. This exemption had previously allowed meters used for sub-billing applications, to be used without Pattern Approval, as required for utility meters. This means that, anywhere a meter or sub-meter is used for trade, sub-billing, or any direct fiscal purpose, NMI Pattern Approved meters must be used. This change brings all meters used in applications mentioned above into line with the National Measurement Act of 1960 Therefore supplying, selling or installing a meter into an application known to be for trade is an offence and carries the heavy penalties associated with the National Measurements Act 1960. 5

monday, october Scan the QR code to view Terminations & Wiring Systems brochures. Scan the QR code to view Enclosures & Climate Control brochures. to view Motor Control & Drives brochures. to view Hazardous Area Equipment brochures. for the safety guide registration form to view the TemPower Rack video. Scan the QR code to view Safety Products brochures. Satisfying all your energy management needs NHP promises to satisfy all of your Energy Management requirements with one of our three tailored solution offerings - Scan the QR code to view Plugs & Sockets to view NHP to view Timers to view Sight & to view the E1 NHPower Component, NHPower Vision and NHPower Control. Renewable Energy & Control Relays Sound brochure. Plus Electronic By brochures. bringing together components brochures. from the brochures. entire NHP product range, including Motor our Protection highly accurate meters, Relays brochure. metering software and accessories you can trust NHP to deliver a customised solution to suit your application. Scan the QR code to view Automation Systems brochures. to view Operator Control Devices brochures. to view Services & Training brochures. to view Metering brochures. For further information on NHP s Energy Management solutions, please scan the QR code to view EMX3 brochure. to view the 193-EC5 Electronic Overload brochure. to view Switching & Sensing brochures. Scan the QR code to view Signalling Devices brochures. to view Power Distribution & Protection brochures. to view Power Quality brochures. to view CUBIC Multi-Drawer solution brochure. Scan the QR code to view the EtherNet/IP Communications Auxiliary Catalogue. NHPower: component If you cannot measure it, you can not improve it. Studies have shown that through measurement alone, energy consumption reductions can be achieved. Scan the QR code to view the Services & Training homepage. NHPower: vision With NHPower Vision, monitoring and reporting of your electrical installation is made easy and provides clear data to assist in making informed strategic decisions to reduce energy costs and consumption. List QR codes_2012.indd 1 5/02/13 1:16 PM NHPower: control As an extension to NHPower Vision, NHPower Control is a comprehensive system allowing realtime decision making based on live data, load shedding, demand management, supply control, etc. as well as complex data manipulation for advanced reporting. 6

kwh meters 7

kwh Meter selection chart LCD Display Single phase system Two phase system Three phase system Active energy kwh system Reactive energy kvarh system Partial active energy Partial reactive energy Current display Voltage display Power display Power demand Maximum demand power Power factor Total harmonic distortion Active energy pulse Reactive energy pulse RS 485 modbus RTU Digital inputs Alarm outputs Accuracy class 1 (active energy) CONTO D1 EM11 DIN CONTO D2B CONTO D2 CONTO D4-Pt CONTO D4-Pd Direct connect 32A 32A 63A 63A 63A Current transformer connect DIN rail mount Panel mount Self power supplied from measurement Page: 10 11 12 13 14 14 1 ) Available with additional module 2 ) Use item 4DIN96ADAPTER 3 ) Ethernet IP on request 8

EM2172 D EM2172R EM4DIN WM22DIN WM24DIN PMW250 1 ) 1 ) 3 ) 100A 100A 65A 2 ) 15 16 17 18 19 20 9

Single phase energy meter Conto D1 The Conto D1 is a basic single phase kwh energy meter. Its single DIN module wide housing allows installation in compact locations. Active energy is displayed on the LCD or can be accumulated by a EMS/BMS via the pulse output. Advantages: High accuracy Compact size (single DIN module) 7 digit wide LCD to represent active energy kwh pulse (1 pulse every 1 watt hour) Technical data: Conto D1 Conto D1 Housing (H x W x D) 90 x 18 x 63mm (1 DIN module) Display type LCD Energy variable: 7 DGT Accuracy Class 1 (kwh) AS62053-21 Refresh rate 1 second System type 1-Phase Voltage inputs 230V AC Current inputs Imax: 32A Digital inputs Measurement variables: Single Phase: kwh Outputs: Pulse 1 Alarm Analogue Ethernet Serial Power supply Self-supplied Protection degree IP40 NHP Recommends Conto D1 Conto D1 + Pulse CE11165A0 CE11165A2 10

Single phase energy analyser EM11 DIN The EM11 DIN is one of the first in the market to include the basic features of a power analyser into an energy meter for one-phase applications. Advantages: Good readability due to wide LCD display Displays active and reactive energy consumption information as well as the status of the power supply Active power alarm notifying an overload condition by means of an internal buzzer Variable control with alarm activation on any available variable Load shedding outputs to prevent overload conditions and thus avoid tripping protective devices EM11 DIN Technical data: ENERGY ANALYSER EM11 DIN Housing (H x W x D) Display type Accuracy Refresh rate System type Voltage inputs Current inputs Digital inputs Measurement variables: Outputs: Pulse Alarm Analogue Ethernet Serial Power supply Protection degree 90 x 17.5 x 67.5mm (1 DIN module) LCD Energy variable: 5+1 DGT Instantaneous variables: 4DGT Class 1 (kwh) AS62053-21 Class 2 (kvarh) AS62053.23 ±0.5 RDG (Current/Voltage) 1 second 1-Phase 230V AC Imax: 32A Single Phase:V L-L, V L-N, A, VA,W,var, WDMD, kwh, kvarh, PF Max: W DMD 1 (open collector) 1 (relay) Self-supplied IP40 for data sheets NHP Recommends EM11 + Relay EM11 + Pulse EM11-DIN-AV81-XR1X EM11-DIN-AV81-X01X 11

Single phase energy meter Conto D2b The Conto D2b is a 2 DIN module single phase energy meter which provides a simple and economical solution for checking your energy consumption. Advantages: High accuracy Compact size 6 digit wide LCD to represent active energy Direct connect up to 36A Technical data: Conto D2b Conto D2b Housing (H x W x D) Display type Accuracy Refresh rate System type Voltage inputs Current inputs Digital inputs Measurement variables: Outputs: Pulse Alarm Analogue Ethernet Serial Power supply Protection degree 89 x 35 x 66mm (2 DIN module) LCD Energy variable: 6 DGT Class 1 (kwh) AS62053-21 1 second 1-Phase 230-240V AC Imax: 36A Single Phase: kwh Self-supplied IP51 NHP Recommends Conto D2b CE21175A0 12

Single phase energy analyser Conto D2 (CE201) The Conto D2 is a 2 DIN module single phase energy analyser that measures active energy and other basic electrical parameters. This meter is a simple and economical solution for checking your energy consumption. The meter is available with either a pulse output or RS485 (Modbus RTU) for EMS/BMS integration. Advantages: High accuracy Compact size 6 digit wide LCD to represent active energy Direct connect up to 63A Pulse or RS485 output Technical data: Conto D2 Conto D2 Housing (H x W x D) Display type Accuracy Refresh rate System type Voltage inputs Current inputs Digital inputs Measurement variables: Outputs: Pulse Alarm Analogue Ethernet Serial Power supply Protection degree 89 x 35 x 66mm (2 DIN module) LCD Energy variable: 6 DGT Instantaneous variables 4 DGT Class 1 (kwh) AS62053-21 1 second 1-Phase 230-240V AC Imax: 63A Single Phase: kwh, A,V, kw, Hz, PF, h 1 Open Collector RS485 Modbus RTU Self-supplied IP51 for data sheets NHP Recommends Conto D2 + Pulse Conto D2 + RS485 CE20195A2 CE20195A4 13

Three phase energy analyser Conto D4 (Pd-Pt) The IME Conto D4 is a cost effective 3 phase energy meter which is simple to install and setup. In addition to a total energy register there is also a resettable partial energy counter. Available with either a pulse or RS485 (Modbus RTU) output, the Conto D4 is ideal for projects which require basic data and communications. Advantages: Conto D4 Backlit LCD display for easy real time viewing Password protected menu Compact 4 DIN size Accurate measurements Partial and total energy registers Technical data: Conto D4 CT connect Direct connect Housing (H x W x D) 89 x 71.2 x 65.6mm (4 DIN module) Display type LCD Instantaneous variables: 8DGT Energy variable: 4 DGT Accuracy Class 1 (kwh) AS62053-21 Class 2 (kvarh) AS62053.23 Refresh rate 1 sec. System type 1, 3-Phase Voltage inputs 230V AC Current inputs Imax: 63A CT: 1/5A CT Digital inputs Measurement variables: System Variables kwh, kvarh, partial (kwh, kvarh), W, VA, var, Hz, PF, W DMD MAX: W DMD Single Phase: V L-L, A Outputs: Pulse 1 Alarm Analogue Ethernet Serial RS485 (Modbus RTU) Power supply Self-supplied Protection degree IP54 for data sheets NHP Recommends D4 Pulse direct connect CE4DT06A2 * D4 RS485 direct connect CE4DT06A4 * D4 Pulse CT CE4DT14A2 D4 RS485 + Pulse CT CE4DT14A6 * Not suitable for 1-Phase systems 14

EM21 72D Three phase energy analyser EM21 72D EM21-72D is an innovative, cost-effective and compact energy meter: it is the first on the market to have a detachable display allowing it to be mounted either on the panel with just 72 x 72mm or on DIN-rail in only 4 modules without an adaptor or external accessory. Advantages: Detachable display allowing three installation modes: DIN-rail energy meter, panel mounting energy meter and transducer. Space saving on panel boards by means of its compact housing. Energy measurements compliant with Australian standards AS 62053-21 and AS 62053-23 Time saving installation system using self-power supply, automatic phase detection and application oriented programming procedure EMS/BMS pulsing output for easy and quick data transmission to RS485 communication port Technical data: EM21 72D Housing (H x W x D) Display type Accuracy Refresh rate System type Voltage inputs Current inputs Digital inputs Measurement variables: Outputs: Pulse Alarm Analogue Ethernet Serial Power supply Protection degree 72 x 72 x 65mm (DIN or Panel Mount) LCD (2 Lines) Energy variable: 7 DGT Instantaneous variables 3 DGT Class 1 (kwh) AS62053-21 Class 2 (kvarh) AS62053-23 ±0.5 RDG (V) ±1 RDG (A) 1 second 1, 2, 3 Phase 120/230V L-N, 400V LL In: 1/5A CT System variables: W, var, PF, Hz, Phase-sequence, kwh, kvarh Single phase variables: V LL, V L-N, A, PF Trms method 1 Static Opto Mosfet RS485 Modbus RTU Self-supplied IP50 for data sheets NHP Recommends EM21 + RS485 EM21 + PULSE EM21-72D--AV53-X0SX EM21-72D-AV53-X0XX 15

EM21 72R Three phase retro fit energy analyser EM21 72R EM21-72R is an innovative, cost-effective and compact energy meter for retro-fit application: it is the first on the market to have a detachable display allowing it to be convertible between a 72 x 72mm panel mount or a 4DIN module unit. Current measurements are carried out by means of external miniature split-core current transformers (included). Advantages: Detachable display Pre-programmed Compact housing Easy to install Pulsing output and /or RS485 (Module RTU) communications for easy and quick data transmission to a EMS/BMS Technical data: for data sheets Housing (H x W x D) Display type Accuracy Refresh rate System type Voltage inputs Current inputs Digital inputs Measurement variables: Outputs: Pulse Alarm Analogue Ethernet Serial Power supply Protection degree EM21 72DR 72 x 72 x 65mm LCD (2 Lines) Energy variable: 7 DGT Instantaneous variables 3 DGT Class 1 equivalent meter Class 2 system (kwh) AS62053-21 Class 2 (kvarh) AS62053-23 ±0.5 RDG (V) ±1 RDG (A) 1 second 1, 2, 3 Phase 120/230V AC, 400V AC In: 90A, Ø10mm In: 150A, Ø 16mm In: 250A, Ø 24mm System Variables: W, var, PF, Hz, Phase-sequence, kwh, kvarh Single Phase Variables: V L-L, V L-N, A, PF Trms method 1 Static Opto Mosfet Trms method RS485 Modbus RTU Self-supplied IP50 NHP Recommends EM2172R + (3x90 A CTs) + RS 485 + pulse EM2172R + (3 x 150 A CTs) + RS 485 + pulse EM2172R + (3 x 250 A CTs) + RS485 + pulse EM2172RVV23XOSX EM2172RVV33XOSX EM2172RVV53X0SX 16

Three phase energy analyser EM4 DIN EM4 DIN is an advanced utility meter capable of measuring not only the usual consumed energies but also gas and water by means of the optional dual contact input module. Advantages: EM4 DIN Modular I/O and comms High accuracy Displays active power demand with manual or external synchronisation. Metering of energy, water and gas in the same instrument Management of the pulses from gas and water meters based on single or dual tariff calculation and energy multi- tariff management Status indication of incorrect current input wiring Self power supply even in case of one phase failure granting continuous metering of energy Technical data: Housing (H x W x D) Display type EM4 DIN 90 x 162.5 x 63mm (9 DIN modules) LCD (2 Lines) Energy variable: 8 DGT Instantaneous variables 31/2 DGT Accuracy Class 1 (kwh) AS 62053-21 Class 2 (kvarh) AS62053-23 Refresh rate 2 second System type 3 Phase unbalanced Voltage inputs 57/100V AC, 120/208V AC 230/400V AC, 380/660V AC Current inputs Imax 100A Digital inputs 2 Independent Measurement variables: System: phase variables: W, W DMD, kwh, kvarh, partial (kwh, kvarh) Phase Variables: W, W DMD T rms Method Outputs: Pulse 2 Open collector Alarm 1 open collector relay Analogue Ethernet Serial RS485 Modbus RTU Power supply 230V AC for data sheets Protection degree IP40 NHP Recommends EM4 DIRECT + RS485 EM4 DIRECT EM4-DIN-100-ASX EM4-DIN-100-AXX 17

WM22 Three phase energy analyser WM22 WM22 DIN is a modular energy analyser that allows all the main parameters of an electrical line or load to be monitored. Advantages: Direct measurement of up to 100A Total harmonic analysis of both current and voltage, notifying potential load failures Phase asymmetry control Plug and play output modules: easy interfacing to external devices Dual pulse output, analogue output, RS485 providing communication to PLCs or PCs Status indication of wrong connection of the current input Technical data: Housing (H x W x D) Display type WM22 90 x 162.5 x 63mm LCD (2 Lines) Energy variable: 71/2 DGT Instantaneous variables 3 1/2 2 DGT Accuracy Class 1 (kwh) AS 62053-21 Class 2 (kvarh) AS62053-23 ±0.5% RDG (Current voltage) Refresh rate 2 second System type 3 Phase unbalanced Voltage inputs 57/100V AC, 120/208V AC 230/400V AC, 380/660V AC Current inputs Imax 100A Digital inputs Measurement variables: System: phase variables:vll, W, Var, VA, PF, V, A, Hz, THD (V, I), kwh, kvarh, partial (kwh, kvarh) W dmd, VA dmd Max: W dmd, VA dmd Phase Variables: V LN, A, W, var, VA, PF, THD T rms Method Outputs: Pulse 2 Open collector Alarm 1 open collector relay Analogue 1 20mA DC, 10V DC Ethernet Serial RS485 Modbus RTU Power supply Self-supplied, + Auxiliary power supply: 230 Protection degree IP40 for data sheets NHP Recommends * WM22 (Auxiliary Power supply) WM22DINAV13DXXX WM22 (Self-supplied) WM22DINAV93XXXX * Modules work with the auxiliary power supplied model. Signal and serial communication comms o 18

EM24 DIN Compact DIN energy analyser EM24 DIN EM24 DIN is a compact energy analyser for three phase unbalanced systems. This new meter is capable of measuring active and reactive energies as well as gas, hot-water, cold-water and remote heating consumption. Advantages: Compact size saves space in switchboards Wide angle variable readability by means of a sharp LCD display (STN technology) High accuracy Total/partial or total/multi-tariff metering Gas, hot-water, cold-water and remote heating measurements Extended alarm control on any available variable Wide interfacing capability using up to 2 pulse outputs or the RS485 communication port Technical data: Housing (H x W x D) Display type EM24 90 x 71 x 65mm (4 DIN modules) LCD (STN technology) Energy variable: 4 DGT Instantaneous variables 8 DGT Accuracy Class 1 (kwh) AS 62053-21 Class 2 (kvarh) AS62053-23 Refresh rate 1.5 second System type Unbalanced: 2-3-phase; bal.:1-3-ph. Voltage inputs 120/208V L-N AC, 400V L-L AC Current inputs In: 1/5A CT Imax: 65A Digital inputs 3 independent (H2O/gas counter or 4-time period selection) Measurement variables: System: phase variables: V LL, V LN, A dmd max, var, VA, W dmd, W dmd max, VA dmd, VA dmd max, Hz. kwh, kvarh, h; Phase Variables: V LL, V LN, A, W, var, VA, PF. kwh, Kvarh T rms Method Outputs: Pulse Alarm Analogue Ethernet Serial Power supply Protection degree 2 Open collector 2 (open collector or relay) RS485 Modbus RTU Self-supplied, 18 to 60V AC/DC, 115/230V AC IP40 for data sheets NHP Recommends EM24 DIRECT + PULSE EM24 CT + PULSE EM24 + RS485 + GAS/WATER INPUTS DIRECT CT CONNECT PANEL MOUNT ADAPTOR KIT EM24-DIN-AV93-XR2X EM24-DIN-AV53-DR2X EM24-DIN-AV93-XISX EM24-DIN-AV53-DISX 4DIN96ADAPTOR 19

Three phase wireless energy meter PowerMonitor W250 The Allen-Bradley wireless PowerMonitor W250 combines high functionality and accurate metering with wireless communications. Utilizing an innovative self generating wireless network the PowerMonitor W250 wirelessly transmits data derived from power meters with built-in Current Transformers (CTs)/Rogowski coils. The PC Receiver can immediately recognize and connect to the PowerMonitor W250 meters without additional configuration. The limited networking necessary to install and operate the wireless PowerMonitor W250 translates to reduced cost and time required for installation, making it a cost-effective, scalable option for a range of industries. PowerMonitor W250 Advantages: Self configurable wireless network Integrated current transformers (CTs)/Rogowski coils) Wireless data communications For use with Wye and Delta systems Time-stamped data Easy to install Limited or no additional network wiring required can help reduce installation and operation costs Fewer components to install and compact size saves time and space Network evaluation tools for troubleshooting are available in FTEnergyMetrix Technical data: PowerMonitor W250 CT model Rogowski Coil Model Mount Wall, DIN Wall,DIN Accuracy Class 1 (kwh) AS 62053-21 Class 1 (kwh) AS 62053-21 System type Wye/Delta Wye/Delta Voltage input 90-300V RMS 180-520V RMS Current input 20-2000A 100-2000A Radio standard (IEEE) 802.15.4 802.15.4 RF Band 2.4 GHz 2.4GHz Operating range (without Router) 30m 30m Operating range (with Router) 260m 260m Frequency 50-60Hz 50-60Hz Power supply Self supplied 24V DC Protection degree IP2X IP2X for data sheets NHP Recommends PMW250 500A Delta (CT) 300V PMW250 500A Delta (Rogowski) 480V 1425D5002MOD 1425D5002MOD480 * Modules work with the auxiliary power supplied model. Signal and serial communication comms o 20

Multi Function and Power Quality Analyser 21

Multi-function and power quality analysers selection chart NEMO D4L NEMO D4L+ NEMO 72L NEMO 96 EM26 WM14 LCD Display 1 phase system 3 phase system Active energy kwh system Partial active energy Negative active energy Reactive energy kvarh system Partial reactive energy Negative reactive energy Phase voltage (Ph to N) Linked voltage (Ph to Ph) Min./Max. voltage Phase current Average current Neutral current Max. demand current Frequency Power factor Voltage sequence diagnostic Active power Reactive power Apparent power Phase power Power demand Max. demand power Total harmonic distortion Hour run Digital inputs Pulse outputs Analogue outputs Alarm outputs RS485 modbus RTU comms Modular inputs Modular outputs Accuracy class 0.5s (active energy) Accuracy class 1 (active energy) Panel mount DIN mount 230-240V Aux power supply 1 ) Page: 24 25 27 30 28 29 22

WM30 WM40 WM5 PM500 PM1000 PM5000 1 ) CL 1 CL 1 CL 0.2 CL 2 CL 1 CL 0.2 34 35 37 32 33 39 23

Three phase multifunction meters NEMO D4L The Nemo D4L is a compact multifunction meter that is simple to use and easy to install. This meter is also capable of measuring energy, power and other electrical parameters. Advantages: Compact size Total and partial energy metering Accurate measurements 2 Level password protected menu composed of a 4 digit numeric combination Technical data: NEMO D4L Housing (H x W x D) Display type NEMO D4L 89.5 x 70 x 65.6mm LCD Energy variable: 8DGT Instantaneous variables 4 DGT Accuracy Class 1 (kwh) AS 62053-21 Class 2 (kvarh) AS62053-23 Refresh rate 1.2 second System type 1, 3 Phase Voltage inputs Un: 30-260V L-N, 50-450V L-L Current inputs In: CT 1/5A Digital inputs Measurement variables: V LL, V LN, A, An, A dmd, THDV, THDI, Hz, PF, W, VA, Var, W dmd, VA dmd, Var dmd, kwh, kvarh, h. voltage sequence diagnostics MAX: A dmd, W dmd, VA dmd, Var dmd Harmonic distortion Up to the 16th Harmonic Outputs: Pulse 1 Alarm Analogue Ethernet Serial RS485 Modbus RTU Dupline Power supply Auxiliary supply 230V AC Protection degree IP52 for data sheets NHP Recommends D4L+RS485 D4L+Pulse MT6FT40026 MT6FTU0026 24

Three phase multifunction meters NEMO D4L+ The Nemo D4L+ is the ideal meter for low and medium voltage applications. It is a simple, compact device with a complete selection of measurement parameters. The Nemo D4L+ has multiple communications with models available with pulse outputs, RS485 Modbus RTU and BACnet MSTP. Advantages: Compact size Easy to install and setup Multiple communications options available Total harmonic distortion for both current and voltage High accuracy Technical data: NEMO D4L+ Housing (H x W x D) Display type NEMO D4L+ 89.5 x 70 x 65.6mm LCD Energy variable: 8DGT Instantaneous variables 4 DGT Accuracy Class 1 (kwh) AS 62053-21 Class 2 (kvarh) AS62053-23 Refresh rate 1.2 second System type 1, 3 Phase Voltage inputs Un: 45-278V L-N, 80-480V L-L Current inputs In: CT 1/5A DigitaliInputs Measurement variables: V LL, V LN, A, An, A dmd, THDV, THDI, Hz, PF, W,VA, Var, W dmd, VA dmd, Var dmd, kwh, kvarh, h. voltage sequence diagnostics MAX: A dmd, W dmd, VA dmd, Var dmd Harmonic distortion Up to the 31st Harmonic Outputs: Pulse 1 Alarm Analogue Ethernet Serial RS485 Modbus RTU BACnet MSTP Dupline Power supply Auxiliary supply 230V AC Protection degree IP52 for data sheets NHP Recommends Nemo D4L+ + RS485 + Pulse Nemo D4L+ + BACnet MF6HT40006 MF6HTB0006 25

Three phase multifunction meters NEMO 72b The Nemo 72b is a low voltage network monitor used for single or three phase applications. The meter has 2 programmable alarms for monitoring min/max electrical parameters. Advantages: Compact size Easy to install and setup Harmonic analysis up to the 16th harmonic 2 programmable alarms Note: No kwh reading on this meter NEMO 72b Technical data: Housing (H x W x D) Display type NEMO 72b 72 x 72 x 81mm LCD Instantaneous variables 4 DGT Accuracy ±0.5% RDG (Current/Voltage) ±0.2% RDG (Frequency) ±2% RDG (Neutral current, Power factor) ±1.5% RDG (Power) Refresh rate 1.2 second System type 1, 3 Phase Voltage inputs 195-260V L-N, 340-450V L-L Current inputs In: CT 1/5A Digital inputs Measurement variables: V L-L, V L-N, A, W, Var, VA, An, Hz, PF, h,w dmd, VA dmd, MAX: W dmd Harmonic distortion Outputs: Pulse Alarm 2 Analogue Ethernet Serial Dupline Power supply Self supplied Protection degree IP54 for data sheets NHP Recommends Nemo 72b NEMO72B13 26

Three phase multifunction meters NEMO 72L The Nemo 72L is a panel mount basic multifunction meter for three phase networks. It can perform accurate electrical measurements and can be used in either EMS or BMS applications. The meter has either a pulse output or serial communications. Advantages: High accuracy for precise energy monitoring LCD Display with adjustable display contrast Phase sequence checking Load failure prevention due to total harmonic distortion analysis Total and partial energy measurements NEMO 72L Technical data: NEMO 72L Housing (H x W x D) Display type Accuracy 72 x 72 x 81 mm LCD Instantaneous variables 4 DGT Class 1 (kwh) AS62053-21) ±0.5% RDG (Current/Voltage) Refresh rate 1.2 second System type 1, 3 Phase Voltage inputs 195-260V L-N, 340-450V L-L Current inputs In: CT 1/5A Digital inputs Measurement variables: V L-L, V L-N, A, An, A dmd, Hz, PF, Voltage sequence diagnostic, W, VA, VAR, W dmd, VA dmd, var dmd, kwh, kvarh, THDI, hour run, MAX: A dmd, W dmd, T RMS Method Harmonic Distortion Up to the 16th Harmonic Outputs: Pulse 1 Alarm Analogue Ethernet Serial RS485 Modbus RTU Dupline Power supply Self supplied Protection degree IP54 for data sheets NHP Recommends NEMO 72L + RS485 NEMO 72L + Pulse NEMO72LRS485 NEMO72LP 27

EM26 96 Three phase power quality analyser EM26 96 EM26 96 is a panel mount power quality analyser for three phase unbalanced systems capable of performing extended consumption analysis as well as monitoring electrical parameters, including harmonics. Advantages: Wide angle variable readability by means of a sharp and two colour back lighted LCD display (STN technology) High accuracy Easy to use Extended energy measurements using total/partial or total/multi-tariff metering Wide interfacing capability using up to 3 pulse outputs or the RS485 communication port 3 Digital inputs allow incrementing registers of gas, hot water and cold water from external pulse meters Extended alarm control on any available variable by means of up to three digital outputs with display warning based on back light colour changing Load failure prevention Technical data: EM26-96 Housing (H x W x D) Display type Accuracy 96 x 96 x 61.4mm Panel mount LCD (2-colour with back light STN technology) Energy variables 8 DGT Instantaneous variables 3x 4 DGT Class 1 (kwh) AS62053-21 Class 2 (kvarh) AS62053-23 for data sheets Refresh rate 1.5 second System type Unbalanced: 2-3-phase; bal.:1-3-ph. Voltage inputs 120/208V L-N AC, 400/660V L-L AC Current inputs In: CT 1/5A Digital inputs 3 independent (H2O/gas counter or 4-time period selection) Measurement variables: Sys: V LL, V LN, An, A dmd max, var, VA, W dmd, W dmd max, VA dmd, VA dmd max, Hz. kwh, kvarh, h; single-phase: V LL, V LN A, W, var, VA, PF, %THD-V, %THD-A, kwh, kvarh T rms method Harmonic distortion THD up to 15th Harmonic (V and A) Outputs: Pulse Alarm Analogue Ethernet Serial Dupline Power supply Protection degree -open collector or 2-relay 3-open collector or 2-relay RS485 (2-wire, Modbus RTU) 18-60V AC/DC, 90-260V AC/DC IP40 NHP Recommends EM26 + RS485 + GAS/WATER EM26 + RS485 + PULSE OUT (2 RELAY) EM26-96-AV53-HI3S1 EM26-96-AV53-HR2S1 28

Three phase power quality analyser WM1496/WM14 DIN WM14 DIN and WM14 96 basic and advanced power analysers can be used in any application where it is required to measure and control the main electrical parameters and transmit them using pulses or serial communication. WM14 is compact and available either for panel mounting or DIN-rail mounting. WM14 Advantages: Metering of both total and partial active and reactive energies with pulse outputs Measurement of the thermal current, by single phase, and recording of the maximum demands Hour counter meter function OR/AND control of up to 16 selected variables so to grant an extended load or line control through 2 digital outputs Technical data: WM1496 WM14DIN Housing (H x W x D) Display type Accuracy 90 x 107.5 x 64.5mm (WM14 DIN) 96 x 96 x 61.5mm (WM14 96) LED Energy variables 8+1 DGT Instantaneous variables 3 DGT Hour Run variable: 5+2 DGT Class 1 (kwh) AS62053-21 Class 2 (kvarh) AS62053-23 WM14 96 Refresh rate 1.5 second System type Unbalanced: 2-3-phase; bal. : 1-3-ph. Voltage inputs 1 00/208V L-N AC; 400/660V L-L AC Current inputs In: CT 1/5A Advanced model: Shunts connect Digital inputs 3 independent (H2O/gas counter or 4-time period selection) Measurement variables: Sys: V LL, An, W, var, VA, W dmd, VA dmd, Hz, Wh, varh, h; single-phase: V LL, V LN, A, W, var, VA, PF, A dmd MAX: W dmd, A dmd T RMS method Harmonic distortion THD up to 16th Harmonic (V and A) WM14 DIN Outputs: Pulse Alarm Analogue Ethernet Serial Dupline Power supply 2 (open collector) 3-open collector or 16 with OR/AND function (2 relays) RS422, RS485 (Modbus RTU) 18-60V AC/DC, 90-260V AC/DC for data sheets Protection degree IP40 (WM14 DIN); IP65 (WM14 96) NHP Recommends WM14-96 + RS485 + PULSE (2 RELAY) WM14-96-AV53-HR2S1 29

Three phase power quality analyser NEMO 96HD The Nemo 96HD is a smart power quality analyser that is highly configurable with a large range of optional modules. It is user friendly and caters to various applications from component based through to energy management and control systems. Advantages: LCD display with adjustable display contrast Phase sequence check System and single phase variables Direct neutral current measurement Total harmonic distortion analysis Modular with a range of communication options NEMO 96HD Technical data: Housing (H x W x D) Display type Accuracy NEMO96HD 96 x 96 x 81mm Panel Mount LCD Energy variables 8DGT Instantaneous variables 4 DGT Class 0.5s (kwh) AS62053-22 Class 2 (kvarh) AS62053-23 Refresh rate 1.1 second System type Single phase, three phase 3 or 4 wire Voltage inputs 50-290V L-N AC; 80-500V L-L AC Current inputs In: CT 1/5A Digital inputs 2 Measurement variables: V L-L, V L-N, V L-Lmin, V L-Lmax,, A, An, A dmd, A maxdmd, AaeveW, VA, Var, W dmd, VA dmd, V ardmd, W maxd-md, VA maxdmd, V armaxdmd, PF, hz, h, kwh±, kvarh± Harmonic distortion THD THDV, THDI (22nd harmonic) Outputs: Pulse 2 Alarm 2 Analogue 2 Ethernet Modbus TCP/IP Serial RS485-Modbus RTU - BACnet MSTP RS232- Modbus RTU Dupline. Power supply 80-265V AC, 110-300V DC, 11-60V DC for data sheets Protection degree IP54 NHP Recommends NEMO 96HD Base Meter NEMO 96HD + RS485 NEMO96HD NEMO96HD1000 30

NEMO 96HD Plug-In Modules Position Description N. Max. Cat. No. A B C D RS485 Communication 1 IF96001 RS232 Communication 1 IF96002 2 Energy pulse outputs 2 IF96003 2 Analogue outputs 0/4...20 ma 2 IF96004 2 Alarms 2 IF96005 Neutral current 1 IF96006 PROFIBUS communication 1 IF96007 LONWORKS communication 1 IF96009 2 IN / 2 OUT SPST 2 IF96010 2 IN / 2 OUT 24 V DC 2 IF96011 MEMORY + R5485 1 IF96012 BACNET MS/TP 1 IF96014 ETHERNET TCP/IP 1 IF96015 Temperature sensor PT100 1 IF96016 A B C D 31

PM500 Three phase multifunction meter PM500 The PM500 is a multifunction meter designed for measurement of electrical parameters in a variety of three-phase and single-phase circuits. Offering digital or analog outputs and Serial Modbus or EthernetIP communications, the PM 500 can be easily integrated into existing energy monitoring systems. The PM500 can assist in providing critical data to reduce energy usage. Advantages: Modular Multiple communication and output models High accuracy Easy to install and setup Four configurable alarms Fully integrated with FTEnergyMetrix software. Technical data: PM500 Housing (H x W x D) Display type Accuracy Refresh rate System type Voltage inputs Current inputs Digital inputs Measurement variables: 96 x 96 x 50mm Panel mount LCD Energy variables 10 DGT Instantaneous variables 4 DGT Class 1 (kwh) AS62053-21 Class 2 (kvarh) AS62053-23 100ms Single phase, three phase 40-144V L-N,70-250V -LL 160-480V L-N, 277-830 V L-L In: CT 5 A Sys: V L-N, V L-L, AN, W, VA, var, PF, Hz, Phase: V L-N, V L-L, A, W, VA, var, PF, All sys and phase variables max and dmd measurements ± kwh, ± kvarh, partial (± kwh, ± kvarh) Harmonic distortion none Outputs: Pulse 2 Alarm 2 Analogue 2 Ethernet EthernetIP Serial RS485 (Modbus RTU) Power supply 90-260V AC/ DC for data sheets Protection degree IP65 Note: Contact NHP for 1420 (PM500) Part numbers Not available in non APR regions 32

PM1000 Three phase multifunction meter PM1000 The PM1000 is a three phase multifunction intended for use in industrial control applications. The PM1000 has native RS485 communication, digital output and EthernetIP or available on request. The meter can be used to communicate power and energy parameters to front end software or control hardware. The PM1000 is available in five models (two transducers, and three energy monitors), with each model suited to a specific application. The PM 1000 is ideal for applications where load profiling, cost allocation, or energy optimisation is required. Advantages: 5 Models Easily to install and use Integration with FTPower, FTEnergyMetrix, and FTView Integrated web page Multiple communications and I/O Panel or DIN rail mounting Time of use (On-Peak, Off-Peak) Logs Energy, Min/Max, Status, and Load Revenue meter accuracy Technical data: PM1000 for data sheets Housing (H x W x D) Display type Accuracy Refresh rate System type Voltage inputs Current inputs Digital Inputs Measurement variables: Harmonic distortion Outputs: Pulse Alarm Analogue Ethernet Serial Power supply Protection degree 90 x 140 x 62mm DIN Mount LCD Energy variables 10 DGT Instantaneous variables 4 DGT Class 1 (kwh) AS62053-21 Class 1 (kvarh) AS62053-21 100ms Single phase or three phase 15-399V L-N, 26-691V L-L In: CT 5A 2 status inputs Sys: Hz, kw, kvar, kva, ± kwh, ± kvarh, kw dmd, kvardmd, kva dmd, Projected dmd (kw, kva, kvar) PF dmd Phase: A, Aave, V L-N, V L-L, VL-Nave, VL-Lave, PF, kw, kvar, kva Logs: (Energy, min max, load factor, time of use, status) none 1 KYZ EthernetIP Ethernet (Modbus TCP/IP) RS485-Modbus RTU) - DH 485 - DF1 85-264V AC, 125-250V DC IP10 Note: Contact NHP for 1408 (PM1000) Part numbers Not available in non APR regions 33

Smart modular power analyser WM30 96 The WM30 is a three-phase smart power analyser with built-in advanced configuration system and LCD data display which is based on a modular housing for panel mounting with IP 65 (front) protection degree. The analyser can be provided with digital outputs that can be either for pulse or/and alarm outputs. The instrument can be equipped with the following modules: RS485/RS232, Ethernet, BACNet-IP communication ports, pulse and alarm outputs. WM30 96 Advantages: One RS232 or RS485 port (on request) BACNet-IP over Ethernet port (on request) Up to 2 digital outputs (pulse, alarm, remote control) (on request) Up to 4 freely configurable virtual alarms Up to 2 analogue outputs (+20 ma, +10 V DC) (on request) Both system and single phase variables with average and max calculation Harmonic analysis (FFT) up to the 32nd harmonic (current and voltage) Run hours counter (8+2 DGT) Real time clock function Application adaptable display and programming procedure (Easyprog function) Technical data: WM30 Housing (H x W x D) Display type Accuracy 96 x 96 x 50mm Panel Mount LCD Energy variables 10 DGT Instantaneous variables 4 DGT Class 0.5 (kwh) AS62053-22 Class 2 (kvarh) AS62053-23 Refresh rate 100ms System type Single phase, three phase 3 or 4 wire Voltage inputs 160-480V L-N AC; 277-830V L-L AC Current inputs In: CT 1/5A Digital inputs Measurement variables: Sys: ± V LL, V LN, A, VA, W, var, PF, Hz, Phase-sequence-asymmetry-loss Phase: V LL, V LN, AL, An, VA, W, var, PF, All variables max and average Total & Partial (±kwh, ±kvarh), THDI, THDV for data sheets Harmonic distortion THD up to 32nd Harmonic Outputs: Pulse 2 Alarm 2 Analogue 2 Ethernet Modbus TCP/IP Serial RS485-Modbus RTU - BACnet MSTP Dupline. Power supply 18 to 60V AC/DC, 90 to 260V AC/DC Protection degree IP65 34

Smart modular power analyser WM40 96 The WM40 is a three-phase smart power analyser with built-in advanced configuration system and LCD data display which is based on a modular housing for panel mounting with IP 65 (front) protection degree. The analyser can be provided with digital outputs that can be either for pulse or/and alarm outputs. The instrument can be equipped with the following modules: RS485/RS232, Ethernet, BACNet-IP communication ports, pulse and alarm outputs.. Parameter programming and data reading can be easily performed by means of Wm40Soft. WM40 96 Advantages: Modular I/O and communications Up to 16 freely configurable alarms with OR/AND logic linkable with up to either 4 relay outputs or up to 6 static outputs (on request) Both system and singles phase variables with average, max and min calculation Direct neutral current measurement (on request) Harmonic analysis (FFT) up to the 32nd harmonic (current and voltage) with harmonics source detection Gas, cold water, hot water, remote heating measurements High accuracy Technical data: WM40 Four quadrant energy measurements (import/export): total and partial kwh and kvarh (inductive and capacitive) or based on 4 different tariffs (on request) Real time clock function Data stamping of up to 10k events: alarm, min, max, I/P status, O/P status, resets, programming changing (on request) Application adaptable display and programming procedure (Easyprog function) Housing (H x W x D) Display type Accuracy 96 x 96 x 50mm Panel Mount LCD Energy variables 10 DGT Instantaneous variables 4 DGT Class 0.5s (kwh) AS62053-22 Class 2 (kvarh) AS62053-23 Refresh rate 100ms System type Single phase, three phase 3 or 4 wire Voltage inputs 160-480V L-N AC; 277-830V L-L AC Current inputs In: CT 1/5 A Digital inputs 6 Measurement variables: Sys:, V LL, V LN, A, VA, W, var, PF, Hz, Phase-sequence-asymmetry-loss Phase: V LL, V LN, AL, An, VA, W, var, PF, All sys and phase variables: min max and average measurement Total & Partial (±kwh, ±kvarh), THDI, THDV for data sheets Harmonic distortion THDI +THDV up to 32nd Harmonic Outputs: Pulse 6 Alarm 6 Analogue 4 Ethernet Modbus TCP/IP Serial RS485-Modbus RTU - BACnet MSTP Dupline. Power supply 90 to 260V AC/VDC Protection degree IP65 35

WM30 / WM40 - Position of modules and combination Position Description Main features A B C Cat. No. WM30 base provided with display, power supply, measuring inputs WM40 base provided with display, power supply, measuring inputs, optical front communication port Dual relay output (SPDT) Inputs/ system: AV5.3 Power supply: H Inputs/ system: AV5.3 Power supply: H 2-channel Alarm or/ and pulse output WM30 AV5 3 H WM40 AV5 3 H M O R2 Dual static output (AC/DC Opto-Mos) 2-channel Alarm or/ and pulse output M O O2 Dual analogue output (+20 ma DC) 2-channel 1 ) M O a2 Dual analogue output (+10 V DC) 2-channel 1 ) M O v2 RS485/ RS232 port module Max. 115.2 Kbps M C 485 232 Ethernet/TCP IP port module RJ45 10/100 BaseT M C ETH BACNet-IP port module Based on Ethernet bus M C BAC-IP Combined digital inputs and Relay outputs (SPDT) Combined digital inputs and Static outputs (AC/DC Opto-Mos) RS485/ RS232 port module with integrated memory Ethernet port module with integrated Memory BACNet-IP port moduile with integrated memory 6-input channels 4-output channels Complex tariff mgmt OR/AND logic mgmt 6-input channels 6-output channels Complex tariff mgmt OR/AND logic mgmt Max. 115.2 Kbps Data stamping RJ45 10/100 BaseT Data stamping Based on Ethernet bus Data stamping 1 ) M F I6 R4 1 ) M F I6 O6 1 ) M C 485 232 M 1 ) M C ETH M 1 ) M C BAC IP M Temperature + process signal measurements (ºC/ºF) Pt type input 20 ma input 1 ) M A T P Direct neutral current measurement + Temperature + Process signal measurement (ºC/ºF) As above + signal input like a common current input (CT ratio etc.) 1 ) M A T P N NOTES: (1) Only one A type module per meter in a maximum combination of 3 total mixed modules on the same meter. (2) Only one A + B type module per meter in a maximum combination of 3 total mixed modules on the same meter. (3) Only one C type module per meter in a maximum combination of 3 total mixed modules on the same meter. (4) Only one B type module per meter in a maximum combination of 3 total mixed modules on the same meter. The B-C position is not mandatory, if to fulfil the application, module A is not necessary, then just B can be mounted. Another example: if modules A and B are not needed, then just module C maybe be mounted. If A module is needed, it is mandatory to put it in A position. 36

Smart power quality analyser WM5 96 WM5 96 is a Smart Power Quality Analyser powered by ARM technology which has significantly improved signal processing and communication speed compared to any other standard analyser. Its superior features make it suitable for applications where high accuracy and performance are required. The WM5 96 is modular and flexible so as to be suitable to the most demanding applications. WM5 96 Advantages: High accuracy Modular - Digital inputs - Digital outputs - Analogue outputs - Serial comms 16 alarms with or/and logic linkable with up to 4 relay outputs and up to 12 open collector ouputs Technical data: WM5 Housing (H x W x D) Display type Accuracy 96 x 96 x 124mm Panel Mount LCD Energy variables 9 DGT Instantaneous variables 4 DGT Class 0.5 (kwh) AS62053-22 Class 2 (kvarh) AS62053-23 for data sheets Refresh rate 100ms System type Single phase, three phase Voltage inputs 120-208V L-N AC; 400-690V L-L AC Current inputs In: CT 1/5A Digital inputs 12 Measurement variables: Sys:, V LL, V LN, An, VA, W, var, PF, Hz, Phase: V LL, V LN, A, VA, W, var, PF, THDV, THDI All sys and phase variables: min max and dmd calculations ±kwh, ±kvarh Harmonic Distortion THD up to 63rd Harmonic Outputs: Pulse 16 Alarm 16 Analogue 8 Ethernet Modbus TCP/IP Serial RS422 RS485 RS232 Dupline. Power supply 18-60V AC/DC 90-260V AC/DC Protection degree IP65 37

WM5 - Position of modules and combination Position Description A B C D E Cat. No. WM5-96 base with ANSI local port AD2001 WM5-96 base without local port AD2000 RS485 port (9,600 bps) (1-port) AR1034 RS485 port (115,200 bps) (1-port) AR2040 Ethernet/ Internet port (1-port) AR1061 Analogue output (20mA DC) (2-out) AO2050 Analogue output (10V DC) (2-out) AO2051 Analogue output (+/-5mA DC) (2-out) AO2052 Relay output (1-out) AO1058 Relay output (1-out) AO1035 Open collector output (1-out) AO1036 Open collector output (2-out) AO1037 Digital input (4-out) AQ1038 Digital inputs + Aux (3-in) AQ1042 RS 232 + RTC AQ1039 NHP Recommends BASE KIT* + RS485 BASE KIT* + ETHERNET BASE KIT* + PULSE OU BASE KIT* WM5-A5H-01003 WM5-A5H-50003 WM5-A5H-000J3 WM5-A5H-00003 38

Three phase power quality analyser PM5000 The PM 5000 is the premier electrical power quality meter from Rockwell Automation. Building on core power and energy metering capabilities, the PM5000 provides advanced technology, new functionality, fast response, and superior accuracy. With multiple communication options the PM5000 can communicate power and energy parameters to controllers, HMI and energy management software. The PM5000 can measure a range of electrical and power parameters and can provide a powerful set of data analytics to understand and take action on power quality issues and energy management activities. PM5000 Advantages: Scalable power quality platform product monitors four voltage and four current channels for each electrical cycle 1024 samples across eight channels every cycle Up to the 127th harmonic Over 6,000 parameters every cycle Waveform Capture Sub-Cycle Transient detection Full metering update every cycle Internal web page Virtual wiring correction capability Configurable alarms for up to 10 events Four inputs WAGES (water, air, gas, electricity, steam) Four outputs Native EthernetIP communication Optional second communication port 0.2% Revenue-accurate meter Technical data: PM5000 for data sheets Housing (H x W x D) Display type Accuracy Refresh rate System type Voltage inputs Current inputs Digital Inputs Measurement Variables: Harmonic Distortion Outputs: Pulse Alarm Analogue Ethernet Serial Dupline Other Power Supply Protection Degree 132 x 185 x 178mm Wall mount Pre-Programmed HMI display module on request Class 0.2 (kwh) AS62053-22 Class 0.2 (kvarh) AS62053-22 (Display on request) Single or Three phase 15 660V LN, 26 1144V LL In: CT 5A 4 inputs Sys: V L-L, V L-n, A, Hz, HzAVE, Vunbalance, Vbalanced, kw, kvar, kva, PFTRUE, PFdisplacement, kvarh, kwh, kvah, DMD (kw, kvar, kva), Proj-DMD (kw, kvar, kva), PFdmd, Crest (V, I), k-factor Logs: Event, Data, Energy, Min/max, Time of use, Setpoint, Load factor, Alarm, Tripper, Data, Power quality Up to the 127th harmonic 3 relay 1 kyz 3 relay 1 kyz EthernetIP Additional module on request Additional communication modules on request 120-240V AC, 24V DC IP10 Notes: * Contact NHP for 1426 (PM5000) item numbers. Not available in non APR regions 39