LIFT CONTROL SYSTEMS CATALOGUE 2007

Transcription

1 LIFT CONTROL SYSTEMS CATALOGUE 2007 All Your Needs For Elevators

2 INDEX 1. Lift Control Cards Speed Control Units Emergency Rescue Cards Lift Control Panels Photocells Door Control Cards Inspection & Alarm Sets Other Products ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 2/18

3 LIFT CONTROL CARDS ARL-500 Functional Programmable Lift Control Card All system parameters can be adjusted by using 6 buttons and an LCD placed on the card; Can be used with any command type up to 48 floors; Can be used at one speed, two speed, speed controlled and hydraulic lifts without any extra parts. System can be selected from the menu; Can be used in group operation up to 8 elevators; All panels in the group are same and no extra panel is needed; Serial communication and pre-wired installation with car and landing modules via CAN BUS; Floor detection is carried out by counter or encoder system. When an encoder is used, braking and stopping adjustment can be made by using the buttons on the card or the buttons on the car panel; Can be used in high speed elevators; Saving errors on system (last 256 records) with date and time information enables to track past errors in detail; Automatic door control according to the stops is achieved by double automatic door support; Side selective door operation individually determined for each stop; RS-232, RS-485 and 2 CAN BUS serial ports; Monitoring the lift status, giving commands, making adjustments and following errors are possible by a connection to a local computer via RS-232 or to a remote computer using a modem; Free programmable inputs and outputs on main controller, car controller and landing modules for special purposes; Integrated door bridging safety relays for door pre-opening and re-leveling; Integrated motor phase protection relay; Hand held terminal for operating the controller from any point of CAN BUS; Designed according to European Lift Standard EN-81. ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 3/18

4 LIFT CONTROL CARDS ARL-300 Functional Programmable Lift Control Card All system parameters can be adjusted by using 4 buttons and an LCD placed on the card; Can be used with any command type up to 24 floors; Can be used at one speed, two speed, speed controlled and hydraulic lifts without any extra parts. System can be selected from the menu; Can be used in group operation up to 4 elevators. All panels in the group are same and no extra panel is needed; Only two cables are needed for group communication; Easily installed and safe detected shaft information gathering system; An error code with its explanation is displayed on the LCD at an abnormal condition. (Ex. H1:Door can not locked); At normal condition the lift can be monitored by messages on the LCD. (Waits for calls, high speed, low speed, inspection); Each floor can be named by an alphanumeric character (L, P, E, F, H, b, o, 0, 1, 2, 3..); 7-segment and signalization outputs are short-circuiting protected. In a short circuit case the concerned output is shut down until problem is removed and a message stating which output is short-circuited is displayed on the LCD. (D segment short-circuited); Only 15 cables are enough for system to work by using serial car connection (FX_SERI) which reduces labor and cable costs; Emergency rescue by 2 pieces of 12V batteries. ARL-SARJ Charge Card controls and charges the battery if necessary; Connection cards, which are used instead of panel terminals, are supplied with flexible parallel connection cables thereby saving extra connection terminals on control panel; Integrated door bridging safety relays for door pre-opening and re-leveling; Integrated motor-phase protection relay; Integrated automatic door control inputs and outputs; Binary or grey code outputs for LCDs and Dot Matrix Displays; Designed according to European Lift Standard EN-81. ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 4/18

5 LIFT CONTROL CARDS ARL-200S Functional Programmable Lift Control Card All system parameters can be adjusted by using 4 buttons and an LCD placed on the card; Can be used with any command type up to 16 floors; Can be used at one speed, two speed and speed controlled lifts without any extra parts. System can be selected from the menu; Can be used in group operation up to 2 elevators. All panels in the group are same and no extra panel is needed; Only two cables are needed for group communication; Floor detection is carried out by counter system. Only 3 magnetic switches for one speed and 4 for two speed systems including limit switches are used for any number of floors; An error code with its explanation is displayed on the LCD in case of an abnormal condition (e.g.. H1:Door can not be locked); At normal condition the lift can be monitored by messages on the LCD (Waits for calls, high speed, low speed, inspection); Each floor can be labeled by an alphanumeric character (L, P, E, F, H, b, o, 0, 1, 2, 3...); 7 Segment and signalization outputs are short-circuiting protected. In case of a short circuit, the related output is shut down until problem is removed and a message stating which output is in short-circuit is displayed on LCD (D segment short circuit); Only 15 cables are enough for system to work by using serial car connection (FX_SERI) which reduces labor and cable costs; No extra switch is needed at high speed lifts (1.6 m/sec) for early slow down; Designed according to European Lift Standard EN-81. ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 5/18

6 LIFT CONTROL CARDS ARL-100 Control Card For Simple Systems All system parameters can be adjusted by using 3 buttons and a 7-segment display placed on the card; Can be used with simple push button command type up to 8 floors; Can be used at one speed and two speed lifts without any extra parts. System can be selected from the menu; Floor detection is carried out by counter system. Only 3 magnetic switches for one speed and 4 for two speed systems including limit switches are used for any number of floors; The current floor is displayed on the 7-segment display during normal operation. An error code with its explanation is displayed in case of an abnormal condition; Contains signal inputs for fire, earthquake, overload, full load, car priority switch; and outputs for direction arrows, car illumination, busy, out of service, and automatic door card; All digital and signalization outputs are short-circuiting protected; System consists of only one unit (22 cm x 11 cm); Economical and practical solution for simple systems; Designed according to European Lift Standard EN-81. ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 6/18

7 SPEED CONTROL UNITS ADrive VVVF Inverter Can be used with open or closed loop systems; High dynamic performance; Contributes to energy-saving; Eliminates startup problems with generators by the help of controlled motor current; Thanks to Space Vector Modulation for high torque motor drive at all speeds; Exclusively designed for elevators. Special parameters for traveling comfort; Compatible with 5V - 24V, TTL, HTL, pnp output, npn output and totem pole output encoder types; 10 KHz IPM switching frequency for low noise motor drive; Integrated DC REACTOR (DCR); 4 low noise fans for efficient cooling; All control inputs and outputs are isolated; User friendly LCD menus for all parameters and faults; PC communication with RS-232 port; Control card communication with RS-485 port; DATA KEY for easy saving and transferring parameters; Overload, high voltage, low voltage, short circuit, power interruption, line phase control, over-heat, grounding fault, over-torque and other necessary protection functions; 7.5kW, 11kW, 15kW and 20kW models are available. ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 7/18

8 EMERGENCY RESCUE CARDS AKUS-SD Emergency Rescue Card In case of a mains failure, the lift stopped between two floors is moved to floor level, the automatic door is opened and passengers are evacuated safely; For lifts with automatic door, in case of a mains failure at floor level, the door is opened and passengers are evacuated; Can be installed in all one speed, two speed or speed-controlled systems; Powered by 5 batteries which need no maintenance; Thanks to Smart Battery Charge System which helps batteries to work for many years; With LCD program, parameters (max travel time, automatic door type, motor drive frequency, door opening time, starting delay, language, etc.) can be adjusted easily; Errors and system data are displayed on LCD; Can work open loop. without connecting a sensor to the motor; The AKUS-SD unit is integrated with control panel. All the connections necessary for emergency unit are done in factory. So the setup time is minimized. ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 8/18

9 EMERGENCY RESCUE CARDS AKUS Emergency Rescue Card In case of a mains failure, the lift stopped between two floors is moved to floor level, the automatic door is opened and passengers are evacuated safely; For lifts with automatic door, in case of a mains failure at floor level, the door is opened and passengers are evacuated; Can be installed in all one speed, two speed or speed-controlled systems; Can be installed in any system regardless of the brand and type of control panel; In case the lift, stopped between two floors due to a control panel failure, can be moved to floor level by using a rescue button placed on the car panel; Powered by 5 batteries which need no maintenance; Thanks to Smart Battery Charge System which helps batteries to work for many years; The battery voltage and error codes are indicated by the display placed on the card; Can work open loop. without connecting a sensor to the motor; Power given to the motor is adjusted automatically, no manual adjustments are needed. ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 9/18

10 LIFT CONTROL PANELS ARL-200S Lift Control Panels Driving Type: o One Speed; o Two Speed; o Speed Controlled; ACVV; VVVF; Open Loop; Closed Loop; o Hydraulic. Command Type: o Simple Push Button; o Up or Down Collective; o Selective Collective; o Group Operation. Car and Shaft System: o Car Serial & Floors Parallel; o Car Parallel & Floors Parallel; Emergency Rescue System: o Integrated into Control Panel; o External; Automatic Door: o Semi Automatic; o Semi Automatic with Cabin Door; o Full Automatic. ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 10/18

11 LIFT CONTROL PANELS AP-AKUS Emergency Rescue Panels In case of a mains failure, the lift stopped between two floors is moved to floor level, the automatic door is opened and passengers are evacuated safely; For lifts with automatic door, in case of a mains failure at floor level, the door is opened and passengers are evacuated; Can be installed in all one speed, two speed or speed-controlled systems; Can be installed in any system regardless of the brand and type of control panel; In case the lift, stopped between two floors due to a control panel failure, can be moved to floor level by using a rescue button placed on the car panel; Powered by 5 batteries which need no maintenance; Thanks to Smart Battery Charge System which helps batteries to work for many years; The battery voltage and error codes are indicated by the display placed on the card; Works open loop. No need to put a sensor on the motor; Power applied to the motor is adjusted automatically, no manual adjustments needed. ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 11/18

12 PHOTOCELLS FSL-FS64 Light Screen FSL-FS32 Light Screens High sensitive protection with 64 infrared diodes (32 transmitter, 32 receiver) in FS64, 32 (16 transmitter, 16 receiver) in FS32; 3,000 mm working range; External 220V AC power supply; 10A relay contact output; seconds delayed buzzer output; 10 mm x 34 mm x 2,000 mm dimensions in FS64, 10 mm x 34 mm x 1,000 mm dimensions in FS32. FSL-1NPF One Sensor Light Barrier FSL-2NPF Two Sensor Light Barrier 1 infrared sensor in FSL-1NPF, 2 infrared sensors in FSL-2NPF; Composed of faced sensors; Has NO/NC relay contact output. ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 12/18

13 DOOR CONTROL CARDS KM_BASIC Door Control Card (Folding Doors) Generally used for replacing old and problematic door cards. This card can be easily adapted to old door systems because an encoder is not needed. It has a fixed openingclosing speed; Powered by a separate battery (Card makes the battery charge), in case of a mains failure; The level of door stuck can be adjusted. KM_GOLD Door Control Card (Folding Doors) KM_DCVAR Door Control Card (Telescopic Doors) By the aid of encoder, travel curve of the door can be adjusted sensitively; Powered by a separate battery (Card makes the battery charge), in case of a mains failure; Door speed, stuck and brake parameters can be adjusted with potentiometers in KM_GOLD; with buttons in KM_DCVAR; The parameters and the error codes are indicated on the display; Has a sound motion warning. ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 13/18

14 INSPECTION & ALARM & ALARM SETS SETS RK12 Standard Inspection Box Has an emergency light output which turns on in case of a mains failure; Alarm, Gong, Battery charge, Inspection switch, Inspection movement buttons; Shelter for lamp, Emergency stop (locked), Socket, Lamp; Large inner volume for comfortable working environment. RK22 Serial Inspection Box Has all standard properties of RK12; FX_SERI (Serial Car Connection Card) is added; No installation is needed between the car and control panel for car buttons, display, overload, full load, gong, direction arrows, car lamp, automatic door close & open buttons and inspection movement buttons. Only security, power and communication connections are needed and 15 cables are enough for connection between car and control panel. EK-1 Manual Controller Manual control from control panel, Inspection switch, Inspection movement buttons; Emergency stop (locked). ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 14/18

15 OTHER PRODUCTS FX_SERI Serial Car Connection Card Communicates with ARL-200S and ARL-300 control cards via two cables; No installation is needed between the car and control panel for car buttons, display, overload, full load, gong, direction arrows, car lamp, automatic door close & open buttons and inspection movement buttons. Only security, power and communication connections are needed and 15 cables are enough for connection between car and control panel. AUTO_KG Automatic Door Card Used with ARL-200S and ARL-100 control card; Can work with all three phase, single phase and electronic-controlled doors; Has light barrier input, door close input and door limit contact inputs; By using two potentiometers, the duration of light barrier's braking and door-open waiting at the floor can be adjusted. ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 15/18

16 OTHER PRODUCTS REV1 Inspection Box Card Works with 24V supply voltage; 12V battery charge and emergency light outputs; Gong output, Alarm output. MKR-02C Motor Phase Protection Card Phase turn control, Adjustable phase voltage control, PTC control; 48V DC leakage current control, Warning LEDs. KUDS Cartop Display Driver Drives the display in car panel according to the signals from magnetic switches; Reduces cable and labor costs. ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 16/18

17 OTHER PRODUCTS GKS Grey Code Driver Converts counter system data to Binary or Grey code. GEVEZE Voice Announcement System ChatterBox is a floor announcement system designed for elevators. It notifies the name or the number of the current floor with a human voice. It also gives overload and out of service warnings; Grey code, binary code and counter modes are available as input modes; ChatterBox board comes loaded with default messages from the factory. But it can also be customized with the help of a personal computer and the ChatterBox Loader Software. ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 17/18