ITEM DESCRIPTION SPECIFICATION TENDER OFFER

Transcription

1 TECHNICAL SPECIFICATIONS PL1 & PL2 PLEASE TICK IF YOU COMPLY. SPECIFY YOUR OPTION IF YOU DON'T. ITEM DESCRIPTION SPECIFICATION TENDER OFFER Make (please specify) 1.0 Type Duplex Passenger Lift 2.0 Minimum Capacity 630kg - 8 persons 3.0 Speed 1.6m/s 4.0 Drive System Electric VVVF drive 5.0 Starts per Hour 180 sph 6.0 Voltage - Power Mains 3pH - 400V - 50Hz(specify power/starting current) 7.0 Voltage - Light Mains 1pH V (50Hz) 8.0 Number of Stops Number of Entrances 8 in line 10.0 Total Travel 25m (approx.) 11.0 Over head Height 3750mm 12.0 Minimum Car Dimensions 1100mm W x 1400mm D x 2100mm H 13.0 Well Dimensions (per lift) 3350mm W x 1800mm D 14.0 Dividing beam Dividing beam between lifts (specify thickness) 15.0 Pit Depth 1550mm 16.0 Location of Machine MRL 17.0 Control System Up and down collective 18.0 Controls & Fittings in Cabin Door Open / Hold button Alarm Bell button Floor address buttons including braille code Fan and Switch Overload indication (audio / visual) Control panel accessible by persons on wheelchair Indirect lighting plus emergency light on battery back-up No Smoking sign Instructions on what to do if lift stops Digital position indicator Provision for camera in cabin Interface for card access control (card access by others) 19.0 Control on Landings Digital position indicator on each floor Engaged / free indicator Direction of travel arrows Gong' signal for lift arrival Lift call buttons Emergency landing door open key / lock 20.0 Maintenance Controls On top of cabin & in control panel 21.0 Car Construction Steel girder and heavy gauge frame all metal parts anti-rust treated MTS Consulting Limited 7

2 TECHNICAL SPECIFICATIONS PL1 & PL2 PLEASE TICK IF YOU COMPLY. SPECIFY YOUR OPTION IF YOU DON'T. ITEM DESCRIPTION SPECIFICATION TENDER OFFER 22.0 Wall Finishes Laminate wood finish Car doors and front returns in brushed stainless steel Full length mirrors positioned on rear wall at the sides with a brushed stainless steel panel in between Hand rail on one side Control panel in black glass or brushed stainless steel finish 23.0 Floor Finishes Recess 20/30mm to take marble (marble by others) 24.0 Ceiling Finish Brushed stainless steel finish Linear lighting 25.0 Car Doors 900mm wide x 2000mm high Side opening Brushed stainless steel finish 26.0 Landing Doors 900mm wide x 2000mm high Side opening Brushed stainless steel finish 1 hour fire rating 27.0 Safety Progressive type safety gear Automatic evacuation control (car travels to nearest landing and opens door in case of power failure) Door closing force limiter Infra-red beam on car door Permanent shaft lighting Cabin roof handrail if distance between cabin and wall exceeds 300mm Intercom between lift and control panel Telephone Line Autodialler to EN81-28 Interface to Fire Alarm System Level switch in pit interfaced to lift operation 28.0 Equipment Guarantee 24 months 29.0 Maintenance 24 months MTS Consulting Limited 8

3 TECHNICAL SPECIFICATIONS FF1 PLEASE TICK IF YOU COMPLY. SPECIFY YOUR OPTION IF YOU DON'T. ITEM DESCRIPTION SPECIFICATION TENDER OFFER Make (please specify) 1.0 Type Simplex Passenger Lift 2.0 Minimum Capacity 630kg - 8 persons 3.0 Speed 1.6m/s 4.0 Drive System Electric VVVF drive 5.0 Starts per Hour 180 sph 6.0 Voltage - Power Mains 3pH - 400V - 50Hz(specify power/starting current) 7.0 Voltage - Light Mains 1pH V (50Hz) 8.0 Number of Stops Number of Entrances 8 in line 10.0 Total Travel 25m (approx.) 11.0 Over head Height 4100mm 12.0 Minimum Car Dimensions 1100mm W x 1400mm D x 2100mm H 13.0 Well Dimensions (per lift) 1750mm W x 1900mm D 14.0 Pit Depth 1550mm 15.0 Location of Machine MRL 16.0 Control System Up and down collective 17.0 Controls & Fittings in Cabin Door Open / Hold button Alarm Bell button Floor address buttons including braille code Fan and Switch Overload indication (audio / visual) Control panel accessible by persons on wheelchair Indirect lighting plus emergency light on battery back-up No Smoking sign Instructions on what to do if lift stops Digital position indicator Provision for camera in cabin Firefighters' control key switch Interface for card access control (card access by others) 18.0 Control on Landings Digital position indicator on each floor Engaged / free indicator Direction of travel arrows Gong' signal for lift arrival Lift call buttons Emergency landing door open key / lock Firefighters' control key switch at level Maintenance Controls On top of cabin & in control panel 20.0 Car Construction Steel girder and heavy gauge frame all metal parts anti-rust treated MTS Consulting Limited 9

4 TECHNICAL SPECIFICATIONS FF1 PLEASE TICK IF YOU COMPLY. SPECIFY YOUR OPTION IF YOU DON'T. ITEM DESCRIPTION SPECIFICATION TENDER OFFER 21.0 Wall Finishes Laminate wood finish Car doors and front returns in brushed stainless steel Full length mirrors positioned on rear wall at the sides with a brushed stainless steel panel in between Hand rail on one side Control panel in black glass or brushed stainless steel finish 23.0 Floor Finishes Recess 20/30mm to take marble (marble by others) 24.0 Ceiling Finish Brushed stainless steel finish Linear lighting 25.0 Car Doors 900mm wide x 2000mm high Side opening Brushed stainless steel finish 26.0 Landing Doors 900mm wide x 2000mm high Side opening Brushed stainless steel finish 1 hour fire rating 27.0 Safety Progressive type safety gear Automatic evacuation control (car travels to nearest landing and opens door in case of power failure) Door closing force limiter Infra-red beam on car door Permanent shaft lighting Cabin roof handrail if distance between cabin and wall exceeds 300mm Intercom between lift and control panel Autodialler to EN81-28 Conformance to EN81-72 Level switch in pit interfaced to lift operation 28.0 Equipment Guarantee 24 months 29.0 Maintenance 24 months MTS Consulting Limited 10

5 TECHNICAL SPECIFICATIONS CH1 PLEASE TICK IF YOU COMPLY. SPECIFY YOUR OPTION IF YOU DON'T. ITEM DESCRIPTION SPECIFICATION TENDER OFFER Make (please specify) 1.0 Type Simplex Car Lift 2.0 Minimum Capacity 3500kg 3.0 Speed m/s - please specify 4.0 Drive System Hydraulic drive - please specify type (direct acting preferred) 5.0 Starts per Hour please specify 6.0 Voltage - Power Mains 3pH - 400V - 50Hz(specify power/starting current) 7.0 Number of Stops Number of Entrances 2 in line 9.0 Total Travel 3m (approx.) 10.0 Over head Height 4200mm 11.0 Minimum Car Dimensions 3400mm W x 5700mm D x 2200mm H 12.0 Well Dimensions (per lift) 3500mm W x 6000mm D 13.0 Pit Depth 3000mm 14.0 Location of Machine Adjacent to lift shaft - please advise size required 15.0 Control System Up and down collective 16.0 Controls & Fittings in Cabin Door Open / Hold button Alarm Bell button Floor address buttons including Braille code Fan and Switch Overload indication (audio / visual) Control panel accessible by persons on wheelchair Indirect lighting plus emergency light on battery back-up No Smoking sign Instructions on what to do if lift stops Digital position indicator Provision for camera in cabin Interface for card access control (card access by others) Key access 17.0 Control on Landings Digital position indicator on each floor Engaged / free indicator Direction of travel arrows Gong' signal for lift arrival Lift call buttons Emergency landing door open key / lock 18.0 Maintenance Controls On top of cabin & in control panel 19.0 Car Construction Steel girder and heavy gauge frame all metal parts anti-rust treated MTS Consulting Limited 11

6 TECHNICAL SPECIFICATIONS CH1 PLEASE TICK IF YOU COMPLY. SPECIFY YOUR OPTION IF YOU DON'T. ITEM DESCRIPTION SPECIFICATION TENDER OFFER 20.0 Wall Finishes Decorative textured finish stainless steel Car doors and front returns in stainless steel Hand rail on one side Bumpers on all walls 21.0 Floor Finishes Stainless steel chequered plate 22.0 Car Doors 2200mm wide x 2100mm high Central opening Decorative textured finish stainless steel 23.0 Landing Doors 2200mm wide x 2100mm high Central opening Decorative textured finish stainless steel 1 hour fire rating 24.0 Safety Progressive type safety gear Automatic evacuation control (car travels to nearest landing and opens door in case of power failure) Door closing force limiter Infra-red beam on car door Permanent shaft lighting Cabin roof handrail if distance between cabin and wall exceeds 300mm Intercom between lift and control panel Autodialler to EN81-28 Level switch in pit interfaced to lift operation 25.0 Equipment Guarantee 24 months 26.0 Maintenance 24 months MTS Consulting Limited 12

7 TECHNICAL SPECIFICATION TABLE OF CONTENTS PASSENGER LIFTS General Regulations and Standards Limits of Work Maintenance Documents to be Submitted with Tender Drawings to be Submitted Inspection and Certificate of Compliance Systems Supply Overvoltage Trip LIFTS Maintenance Control Gear Samples Telephone and Camera in Lift Cabin Essential Power Supply / Automatic Evacuation Fire Control Access Control Firefighters s Lift SUMP PUMPS General Designation Design Operating Parameters 6 MTS Consulting Ltd 1

8 PARTICULAR SPECIFICATION PASSENGER LIFTS 1.0 GENERAL 1.1 Regulations and Standards The lifts, the material and the installation including the machine room and pit shall comply with all the relevant standards and regulations. In particular: (i) European Parliament and Council Directive 95/16/EC of 29 June 1995 as adopted in Malta, by virtue of the Legal Notice 370 of 2002 Lifts Regulations. All lifts and safety components within the scope of the Regulations, which are to be provided under this contract will have to: Be safe (or in the case of a safety component enable the lift in which it is installed to be safe); Meet the relevant essential health and safety requirements in their design, construction and installation; Satisfy the appropriate conformity assessment procedures set out in the Regulations. Carry CE marking; Be accompanied by an EC declaration of conformity. (ii) Maltese Standard MSA EN for the hydraulic lift, MSA EN for the electric traction lift, as applicable. (iii) European standard EN for firefighters lift, as applicable. (iv) European standard EN for safety rules for the construction and installation of passenger lifts, particular applications for passenger and goods passenger lifts and accessibility to lifts for persons including persons with disability. (v) Factories (Hoists and Lifts) Regulations, (vi) Current Edition of the I.E.E. Wiring Regulations. (vii) Current Edition of the Electricity Supply Regulations as issued by the Enemalta Corporation. The Tenderer shall be required to certify, at tendering stage, that the whole installation will conform to the above standards and regulations. MTS Consulting Ltd 2

9 Any deviations from the above standards must be clearly indicated by the contractor at tendering stage. 1.2 Limits of Work All civil engineering works, including pit, lift well motor room and relative openings, shall be carried out by others. The supply and fixing of any part of any metal structure necessary for the operation of the lift shall, however, form part of this tender. 1.3 Maintenance The tenderer shall cover complete maintenance of the equipment and the installation for a period of twenty-four (24) months following handover. The maintenance shall be in line with the Maltese Standard MSA EN 13015:2001. This shall also include routine bimonthly visits as necessary, to keep the lifts in continuous working order, the free supply and use of lubricants, all replacements, including lights and batteries, etc. A six monthly examination by a competent person shall also be undertaken, on the general operation, running clearances, main drive system and gearing and operational check of safety devices. A report of Examination of Lift shall be compiled and copies passed to client, competent Authorities and the O.H.S.V. A log book shall be kept in order to record dates and nature of visits and condition of lifts. 1.4 Documents to be Submitted with Tender The tenderer shall submit with his tender the following documentation : a. Descriptive brochure regarding cabin and doors finishes he is proposing. b. Certification that the whole installation shall conform to standards as specified in 1.1 above. c. Reference list of projects with similar type / capacity lifts. d. Confirmation that lift shaft dimensions are acceptable and will accommodate proposed lift installation. 1.5 Drawings to be Submitted The successful contractor shall within 4 weeks from signing of contract submit the drawings / documents listed hereunder: Three sets of general arrangement drawings, indicating also civil engineering works to comply with the dimension of the lift shafts as indicated in the drawing and all other relevant builder s work. 1.6 Inspection and Certificate of Compliance Prior to handing over of the lift, the contractor shall obtain the certificate of inspection in accordance with the Factories (Hoists and Lifts) Regulation, 1964 and the Certification of a Notified Body. 1.7 Systems Supply All equipment and components, including cabins and their accessories, shall be supplied as a complete system by the same manufacturer, details of which are to be submitted with the tender. MTS Consulting Ltd 3

10 1.8 Overvoltage Trip A three phase motor protector is to be supplied and installed for each motor. The motor protector is to automatically isolate the power supply to the motor in the event of: a. A phase loss. b. A phase reversal. c. A 9% voltage difference between phases. d. A phase angle variation of more than 10%. e. The voltage goes below the under voltage setting. f. The voltage goes above the over voltage setting. The adjustable voltage setting ranges are to be: under voltage over voltage 300 to 500 volts 360 to 560 volts The tripping unit can be reset automatically or manually after a set time delay in the range of 20 to 300 seconds. 2.0 LIFTS 2.1 Maintenance Control Gear Up / Down / Stop / Control and Inspection buttons to be installed in control panel as well as on top of car. 2.2 Samples It is very important for the client that samples of the finishes be forwarded with the tender document. 2.3 Telephone and Camera in Lift Cabin The travelling cable in all lifts shall include a dedicated line for the telephone. It is important that the lifts contractor provides a telephone line for this particular lift and as such all necessary co-ordination shall be the responsibility of the contractor. A co-ax cable for future installation of a camera in the lift cabin is to be provided. This cable shall be terminated in appropriate individual box fixed to the wall besides the lift control panel. 2.4 Essential Power Supply / Automatic Evacuation Essential power supply shall be provided for the firefighter s, lift FF1. A power supply from the essential system, off the building s stand-by generator, will be provided (by others) to feed the control panel and will be terminated in a main switch in the shaft. The passenger lifts PL1 and PL2, and the car hoist CH1 shall be equipped with an automatic evacuation control. This will allow the lifts to move to the nearest floor and allow evacuation of any trapped passengers. The operation of the lift will cease until power is restored. FF1 shall also be provided with an automatic evacuation control that will be required in the event that the generator does not operate. MTS Consulting Ltd 4

11 2.5 Access Control All lifts shall be provided by means of a card access control system, which shall be provided by the access control contractor. In view of this, an interface shall be allowed in each lift cabin for connection by the access control contractor. The car hoist, in addition to the interface described above, shall also have a key access control that will only allow travelling between floors by use of a key. This is to be provided by the lift s contractor. 2.6 Fire Control On receipt of a signal from the Fire Alarm Panel, all the lifts shall descend / ascend to the pre-assigned (evacuation) floor, open doors to allow passengers out, then remain stationary with doors closed. FF1 shall be assigned as firefighters s lift. Thus on the cabin control panel and on the landing at ground floor (to be confirmed by the Engineer prior to installation) there shall be a firefighters s control key switch. The relative keys are to be handed over to the Estate Manager on commissioning. The firefighters s switch shall include a two-phase operation for lift calling and lift operation as specified in EN Further requirements specified in EN81-72 shall also be included, such as its positioning and labelling. 2.7 Firefighters s Lift The lift designated to be firefighters s lift shall be so designed to ensure proper operation during a fire, as specified in EN Compliance shall be ensured for the electrical and electronic landing control devices, car and landing controls, and all other necessary equipment. The lift shall include an emergency trap door that ensures a means of escape from the car. This trap door shall form part of a complete system that allows evacuation at any point, as specified in EN A sump pump shall be supplied and installed within this scope of works to prevent the water level in the pit from reaching the car or equipment which could create malfunction of the firefighters lift. The pump shall be as specified in section SUMP PUMP The contractor shall supply, install, test and commission the submersible pumps including electrical connection and 50mm diameter HDPE discharge pipework (allow for 15meters of pipework). 3.1 General The sump pump shall be a submersible motor pump for percolating or leakage water. It shall be suitable for handling chemically neutral, slightly contaminated wastewater containing solids with a grain size of up to 10 mm as well as wash water and sea water. The sump pump shall not be required to pump sewage or corrosive liquids. MTS Consulting Ltd 5

12 3.2 Designation When selecting the brand and model, contractor shall ensure that the variant suitable for aggressive water, such as sea water, is chosen. A typical pump suitable for this use is : Brand : KSB Model : Ama-Drainer 301 S E Variant : C = variant for aggressive water An equal and approved brand and model may be offered provided the manufacturer guarantees its use for the application specified. 3.3 Design The pump shall be: vertical submersible motor pump, single-stage, with level control. The motor shall be single phase (230v), equipped with thermal motor protection with automatic reset and start-up. The motor is cooled by the medium pumped. The pump shall include a non-return valve and a female thread connection socket. All wetted components are manufactured from materials that can withstand corrosion. The motor shall include sealed-for-life grease-lubricated bearings, and a settable float switch. 3.4 Operating Parameters Head max. 6.5 m Capacity max. 9 m 3 /h Immersion depth max. 2 m Voltage/frequency max. 230 V / 50 Hz Max. temperature, continuous 0 up to 35 C Grain size 10 mm max. Power input 350 W max. Type of protection IP 68 Noise level <70 db(a) Supply cable 10 m H07RNF MTS Consulting Ltd 6

13 BANK OF VALLETTA TENDER DOCUMENT JOB NO.: C/43284 DATE: AUGUST 2015