VARIABLE SPEED CONTROL CPMD CONNECTIONS

Size: px

Start display at page:

Download "VARIABLE SPEED CONTROL CPMD CONNECTIONS"

Aleesha Pope
10 years ago
Views:

1 VARIABLE SPEED ONTROL PMD ONNETIONS INLET DRAIN ONNETOR ORIENTATION (side view) PROBE MINIMUM SPEED ADJUST DIAGSTI LEDS TE: SPLASH OVER T SHOWN FOR LARITY. IRUIT BREAKER MAINS ONNETOR - SEELEY INTERNATIONAL OMMERIAL ATALOGUE 0

DIAGSTI LEDS TE: SPLASH OVER T SHOWN FOR LARITY.

2 WIRING DIAGRAM SPEED PHASE PRE JAN 00 THESE WIRING INSTRUTIONS FOR UNITS MADE PRIOR TO JANUARY 00 WHERE THE MAINS POWER IS SUPPLIED TO WALL SWITH TWO SPEED SINGLE PHASE RP WIRING DIAGRAM 09 ISOLATION BOX WIRING INSTRUTIONS. THE IMING MAINS POWER MUST BE TAKEN DIRETLY TO THE WALL SWITH.. WIRES AND AN ARE REQUI BETWEEN THE OOLER AND THE WALL SWITH. ALL FIELD WIRING IS SHOWN AS SPEED FAN LO HI (low) (high) POLE ISOLATOR 9 0 E A N * LO/HI FAN OOL N A E WALL SWITH (VIEWED FROM REAR) SEELEY INTERNATIONAL OMMERIAL ATALOGUE

THE IMING MAINS POWER MUST BE TAKEN DIRETLY TO THE WALL SWITH.. WIRES AND AN ARE REQUI BETWEEN THE OOLER AND THE WALL SWITH.

3 WIRING DIAGRAM SPEED PHASE - pre NEON WALL SWITH PHASE WIRING DIAGRAM Lo/Hi WALL SWITH Fan ATIVE ool TO TERMINAL POINT L L L N E SWITH RPB RPA0-900 TO POINT BLAK (Neutral) E N L L L SWITH RPB00-00 RPA DRAIN KIT OMPONENTS Electronics Solenoid enclosure enclosure FAN LO FAN HI FIELD WIRING * BLAK A AG 0V BLAK BLAK To Isolating Switch 9 A A A A 0 L L L N ONTATOR T T T N L L L N ONTATOR T T T N N N ONNETION ALL MODELS T T T T T T *Link wire removed when drain is installed. connections are as follows; Brown wire to terminal Blue wire to terminal Red wire to terminal Orange wire to terminal (TO PLATFORM) POINT SEELEY INTERNATIONAL OMMERIAL ATALOGUE

Isolating Switch 9 A A A A 0 L L L N ONTATOR T T T N L L L N ONTATOR T T T N N N 9 9 9 9 9 9 9 9 ONNETION ALL MODELS T T T T T T *Link wire removed when drain is

4 WIRING DIAGRAM SPEED PHASE - NEON WALL SWITH DRAIN KIT 0 PHASE WIRING DIAGRAM WALL SWITH Lo/Hi Neon Fan Neon ATIVE ool NEUTRAL TO TERMINAL POINT L L L N E SWITH RPB RPA0-900 TO POINT BLAK (Neutral) E N L L L SWITH RPB00-00 RPA DRAIN KIT OMPONENTS Electronics enclosure Solenoid FAN LO FAN HI FIELD WIRING * BLAK A AG 0V BLAK Sensor BLAK To Isolating Switch 9 A A A A 0 L L L N ONTATOR T T T N L L L N ONTATOR T T T N N N ONNETION ALL MODELS T T T T T T *Link wire removed when drain is installed. connections are as follows; Brown wire to terminal Orange wire to terminal White wire to terminal Blue wire to terminal (TO PLATFORM) POINT SEELEY INTERNATIONAL OMMERIAL ATALOGUE

BLAK To Isolating Switch 9 A A A A 0 L L L N ONTATOR T T T N L L L N ONTATOR T T T N N N 9 9 9 9 9 9 9 9 ONNETION ALL MODELS T T T T T T *Link wire removed when drain is

5 WIRING DRAIN DIAGRAM KIT 0 SPEED PHASE - NEON WALL SWITH THESE WIRING INSTRUTIONS ARE FOR UNITS MADE FROM JANUARY 00 WIRING INSTRUTIONS. THE IMING MAINS POWER MUST BE TAKEN DIRETLY TO THE OOLER.. WIRES ARE REQUI BETWEEN THE OOLER AND THE WALL SWITH.. FOR DRAIN KIT WIRING INSTRUTIONS SEE MANUAL SUPPLIED IN KIT OR VISIT OUR WEB SITE ALL FIELD WIRING IS SHOWN AS SPEED FAN A E N LO HI POLE ISOLATOR LOW HIGH OMMON DRAIN KIT OMPONENTS Electronics enclosure Solenoid 9 0 Sensor * FAN LOW FAN HIGH ATIVE NEON NEON E A N * LO/HI FAN OOL (VIEWED FROM REAR) connections are as follows; Brown* wire from pump to terminal Brown wire to terminal Blue wire to terminal White wire to terminal Orange wire to terminal SEELEY INTERNATIONAL OMMERIAL ATALOGUE

. FOR DRAIN KIT WIRING INSTRUTIONS SEE MANUAL SUPPLIED IN KIT OR VISIT OUR WEB SITE www.braemar.com.

INSTALL INSTRUCTIONS KK-C-HVAC-1 HVAC UNIT 2003-2014 CHEVROLET/GMC VANS FOR

INSTALL INSTRUCTIONS KK-C-HVAC-1 HVAC UNIT 2003-2014 CHEVROLET/GMC VANS FOR (For NEW 2007 ALL WHITE KWIK-KITS ONLY) Warning do not attempt to install A/C units unless you are experienced with servicing