1.8 w Port Solenoid Valve Direct Operated Poppet Type. New. Series VT307 CAT.ES11-107A. Power consumption

Transcription

1 Port Solenoid Valve Direct Operated Poppet Type Power consumption Vacuum applications New [Option] RoHS 4 Standard wtype (Existing product: 4.8 W) 0. kpa Energy-saving type.8 w (Existing product: W) A single valve with various valve functions (Universal porting type) N.C. valve Divider valve N.O. valve Selector valve etc Low concentration ozone resistant Rubber seal material: HNBR for main valve Mounting dimensions are interchangeable with existing product 9.5. Body ported type Manifold type Series VT07 CAT.ES-07A

2 Series VT07 Port Solenoid Valve Direct Operated Poppet Type A variety of valve options Continuous duty type Vacuum specification type Energy-saving type Energy-saving type + Vacuum specification type Application examples q Blow-off valve w Pressure release valve e Selector valve r Valve for vacuum (P) (R) (A) (P) (R) X Plug (A) P P (P) (R) (A) Vacuum pump (P) (R) (A) Vacuum pad Vacuum releasing air Atmospheric pressure or micro pressure t Divider valve y Single-acting cylinder drive u Double-acting cylinder drive i Double-acting cylinder drive (Exhaust center) Tank (P) (R) Tank (A) (P) (R) (A) N.C. (A) (P) (R) (P) N.O. (A) (R) N.C. (A) (P) (R) (P) N.C. (A) (R) Port Solenoid Valve, Universal Porting Type Variations Poppet type Direct operated poppet type Pilot poppet type Series New VT07 VT7 VT5 VP00/500/700 Cv (P A) to.6 Refer to the SMC website for details. Features

3 Port Solenoid Valve Direct Operated Poppet Type Series VT07 Rubber Seal RoHS [Option] Note) CE compliant: Electrical entry is applicable only for the DIN terminal. How to Order V T 07 5 G 0 F T O Body type Body ported For manifold Valve option Nil Standard type E Continuous duty type Y Energy-saving type V Vacuum specification type W Energy-saving type, Vacuum specification type Semi-standard Pressure specifications Nil Standard type (0.7 MPa) K High-pressure type ( MPa) Semi-standard Grommet Rated voltage 00 VAC, 50/60 Hz 00 VAC, 50/60 Hz 0 VAC, 50/60 Hz 4 0 VAC, 50/60 Hz 5 4 V 6 V 7 40 VAC, 50/60 Hz Semi-standard Electrical entry DIN terminal Thread type Nil Rc F G N NPT T NPTF CE-compliant Nil None Q CE-compliant Electrical entry and light/surge voltage suppressor: D/DO/DZ/DOZ only Bracket Nil None F With bracket Port size Nil Without port (For manifold) 0 /8 (6A) 0 /4 (8A) Light/Surge voltage suppressor Nil None With surge voltage suppressor S (Grommet type only) With light/surge voltage suppressor Z (DIN terminal type only) With surge voltage suppressor Surge voltage suppressor G: 00 mm lead wire H: 600 mm lead wire D: With connector JIS Symbol (A) (R) (P) DO: Without connector Manifold Model Applicable manifold type Accessories Function plate (DXT5-4-A) VO07 (-Q) Common or individual exhaust Note) Mounting screw (NXT0-) Note) It is not applicable to the continuous duty type. Refer to the accessories on page 5. Option Description Bracket Part no. DXT5-5-A (With screw)

4 Series VT07 Standard Specifications Make sure that dust and/or other foreign materials do not enter the valve from the unused port (e.g. exhaust port). Flow-rate Characteristics/Weight Type of actuation Fluid Operating pressure range Ambient and fluid temperature Response time Note ) Max. operating frequency Lubrication Mounting orientation Impact/Vibration resistance Note ) Enclosure Electrical entry rated voltage (V) Allowable voltage fluctuation Note ) Note 4) Apparent power AC Note ) Note 4) Power consumption Light/Surge voltage suppressor (DIN terminal type only) Direct operated type position single solenoid Air 0 to MPa (High-pressure type), 0 to 0.7 MPa (Standard type) 0 to 50 C (No freezing) 0 ms or less (at 0.5 MPa) 0 Hz Not required (Use turbine oil Class ISO VG, if lubricated.) Non-locking push type Unrestricted 50/50 m/s Dustproof AC (50/60 Hz) Inrush Holding AC Grommet, DIN terminal 00, 00, 0, 0, 40 4, 5 to +0% of rated voltage.7 VA (50 Hz), 0.7 VA (60 Hz) 7.6 VA (50 Hz), 5.4 VA (60 Hz) Without indicator light: 4 W, With indicator light: 4. W Varistor, LED Diode, LED Semi-standard Note ) Based on dynamic performance test, JIS B ( temperature: 0 C, at rated voltage, without surge voltage suppressor) Note ) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction and at the right angles to the main valve and armature in both energized and de-energized states every once for each condition. (Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Note ) At rated voltage Note 4) The value is different for continuous duty type (VT07E), and energy-saving type (VT07Y/W). Refer to Valve Options shown below. Valve model Flow-rate characteristics Port (P A) (A R) (R A) (A P) size C[dm /(s bar)] b Cv C[dm /(s bar)] b Cv C[dm /(s bar)] b Cv C[dm /(s bar)] b Cv VT07 VT07V (Vacuum spec. type) VT07E (Continuous duty type) /8 VT07Y (Energy-saving type) VT07W (Energy-saving, Vacuum spec. type) VT07 VT07V (Vacuum spec. type) VT07E (Continuous duty type) /4 VT07Y (Energy-saving type) VT07W (Energy-saving, Vacuum spec. type) Note) Values for a single valve unit. It is not applicable to the manifold. Refer to the manifold specifications on page 5. Weight Grommet 0.5 kg Valve Options Continuous duty type: VT07E Exclusive use of VT07E is recommended for continuous duty with long time loading.. This model is for continuous duty, not for high cycle rates. But even in low cycle rates, if energizing the valve more than once a day, please consult with SMC.. Energizing solenoid should be done at least once in 0 days. Specifications different from standard are as follows. Apparent power/ Inrush 7.9 VA (50 Hz), 6. VA (60 Hz) AC Holding 5.8 VA (50 Hz),.5 VA (60 Hz) Power consumption/.8 W, With indicator light: W Response time Note) 0 ms or less (at 0.5 MPa) Note) Refer to Note ) of the standard specifications. Energy-saving type: VT07Y (VT07W) If low power consumption is required for electronic control, VT07Y(W) (.8 W) is recommended. Specifications different from standard are as follows. Power consumption/.8 W, With indicator light: W Response time Note) 5 ms or less (at 0.5 MPa) Note) Refer to Note ) of the standard specifications. Vacuum spec. type: VT07V (VT07W) This vacuum model has less air leakage than the standard model under low pressure. It is recommended for vacuum application. Since this valve has slight air leakage, it can not be used for vacuum holding (including positive pressure holding) in the pressure container. Specifications different from standard are as follows. Operating pressure range 0. kpa to 0. MPa

5 Port Solenoid Valve Direct Operated Poppet Type Series VT07 Construction De-energized r Energized t Light/Surge Voltage Suppressor AC In the case of indicator light assembly Terminal no. q r y u q Terminal no. In the case of indicator light assembly Terminal no. (+) (Å) w e (Â) Operation principle <De-energized> Poppet valve w is pushed upward by the return spring e, port is closed. Then, port and port are connected. Air flow direction: Port Block, Component Parts No. 4 Description Body Poppet valve Return spring Molded coil How to Use DIN Terminal. Disassembly ) After loosening the screw q, then if the housing w is pulled in the direction of the screw q, the connector will be removed from the body of equipment (solenoid, etc.). ) Pull the screw q out of the housing w. ) On the bottom part of the terminal block e, there s a cut-off part o. If a small flat head screwdriver is inserted between the opening in the bottom, terminal block e will be removed from the housing w. 4) Remove the cable gland r, plain washer t and rubber seal y.. Wiring ) Pass the cable u through the cable gland r, plain washer t and rubber seal y in this order, and then insert them into the housing w. ) Loosen the screw! attached to the terminal block e. Then, pass the lead wire!0 through the terminal block e and tighten the screw! again. Note ) Tighten within the tightening torque of 0.5 N m ±5%. Note ) Cable u outside diameter: ø6 to ø8 mm Note ) Crimped terminal like round-shape or Y-shape cannot be used. Connector for DIN Terminal Description DIN connector Part no. BB09-A (Standard) GM09NJ-B7 (CE-compliant) ( ) (Å) ( ) Material Aluminum die-casted Aluminum, HNBR Stainless steel Resin w e (Â) <Energized> When energizing the molded coil r, the armature t is magnetically attracted to the core y, and through the push rod u, it pushes down the poppet valve w and port is closed. Then, port and port are connected. At this time, there will be gaps between the armature t and the core y, but the armature t will be magnetically firmly attracted to the core y. Air flow direction: Port Port, Port Block Note Color: White. Assembly ) Pass the cable u through the cable gland r, plain washer t and rubber seal y in this order and connect to the terminal block e. Then, mount the terminal block e on the housing w. (Push it down until you hear the click sound.) ) Put the rubber seal y and plain washer t in this order into the cable entry of the housing w, and then tighten the cable gland r securely. ) Insert the gasket i between the bottom part of terminal block e and the plug attached to the equipment. Then, screw in q from the top of the housing w to tighten it. Note ) Tighten within the tightening torque of 0.5 N m ±0%. Note ) Connector orientation can be changed 80 depending on how the housing w and the terminal block e are assembled. e i q w o!!0 y t u r Terminal no. ( ) Electrical Connection DIN terminal is connected inside as in the figure below. Connect to the corresponding power supply. DIN terminal block Voltage 00 VAC 00 VAC Others Ground Applicable cable O.D. ø6 to ø8 Terminal no. DIN terminal Lead Wire Color + Color Blue Red Red (+), Black ( ) Gray

6 Series VT07 Dimensions Grommet: VT07- G x ø4.5 (For mounting) (4.5) (4.5) Note) There is also VT07- H (lead wire length: 600 mm). Applicable cable O.D. ø6 to ø8 (4) () (7.) x ø4.5 (For mounting) (4.5) (4.5) (8) (7) (4.5) Pg9 Max (4) () (7.) (4.5) (8) (7) G: 00 H: 600 (Lead wire length) (.) 6.5. /4", /8" (Piping port) M4 x 0.7 thread depth 7 (Mounting screw) 5 DIN terminal: VT07- D (.) 6.5. /4", /8" (Piping port) 4 M4 x 0.7 thread depth 7 (Mounting screw) 5

7 Series VT07 Manifold Specifications VT07 manifold is available both as a common exhaust and individual exhaust model. Manifold valve can be easily converted from N.C. (Normally Closed) to N.O. (Normally Open) merely by turning over the function plate. Common exhaust VV F Individual exhaust VV F VV07 VT07 manifold How to Order Manifold Base F Dummy symbol Valve stations 0 stations 0 0 stations Max. 0 stations Specify model number of the manifold base, applicable valves and blanking plates when ordering. Refer to page for the model number of the valves. Ordering example: VV F pc. (5 station manifolds base) VO07-G 4 pcs. DXT060-5-A pc. (Blanking plate) Manifold Specifications Manifold type Max. number of stations Applicable solenoid valve Exhaust port Symbol Type Common Individual P Base (Side) 8 Base (Side) A port size (Base mounted) common exhaust/individual exhaust 4 individual exhaust Exhaust port type Common exhaust Individual exhaust Mounting bracket Thread type Nil F N T Rc G NPT NPTF B mount 0 stations Note) VO07 - (-Q) Port location (Direction)/Port size A R Base (Side) Base (Side) 8 8 Base (Side) Base (Top) 4 8, 4 8 Note) For 6 stations or more, supply air both sides of P port. The common exhaust type should exhaust from both of the R port. Option Description Blanking plate (With gasket, screw) Note) Part no. DXT A B Accessories for Applicable Solenoid Valve Description Part no. Qty. Function plate (With gasket) Note) Mounting screws DXT5-4- A B NXT0- pc. pcs. Note) DXT060-5-B, DXT5-4-B are for the continuous duty type. Flow-rate Characteristics/Weight Flow-rate characteristics Valve model (P A) (A R) (R A) (A P) VO07 VO07V (Vacuum spec. type) VO07E (Continuous duty type) C[dm /(s bar)] 0.4 b 0.8 Cv C[dm /(s bar)] 0.4 b 0. Cv 0.08 C[dm /(s bar)] 0.6 b 0.8 Cv 0.09 C[dm /(s bar)] 0.4 b 0.8 Cv VO07Y (Energy-saving type) VO07W (Energy-saving, Vacuum spec. type) Weight Grommet 0.5 kg 5

8 R P Series VT07 Dimensions: Common Exhaust VV F G: 00 H: (Pitch) P = 6 8 L 9 0 L Max. 0 P R DIN terminal (D, DZ) Applicable cable O.D. ø6 to ø8 Pg9 Grommet (G, H) For 4 x M4 (For mounting) /8" [(P), (R) port] (Station n) (Station ) (5) A A 40 /8" [(A) port] (Pitch) P = 6 L Dimension L L L n n: Stations Formula L = 6 x n + 6 L = 6 x n + 0 6

9 Port Solenoid Valve Direct Operated Poppet Type Series VT07 Dimensions: Individual Exhaust VV F (Pitch) P = DIN terminal (D, DZ) 8 7 /8" [(R) port] L Applicable cable O.D. ø6 to ø8 Grommet (G, H) (Pitch) P = For 4 x M4 (For mounting) 4.6 R R P () Pg9 0 /4" [(P) port] 8.5 G: 00 H: L (Station n) (Station ) Max A A /4", /8" [(A) port] (Pitch) P = 6 L Dimension L L L n n: Stations Formula L = 6 x n + 4 L = 6 x n + 7

10 Series VT07 Specific Product Precautions Be sure to read before handling. Refer to back cover for Safety Instructions and Handling Precautions for SMC Products (M-E0-) for /4/5 Port Solenoid Valve Precautions. Warning Mounting When mounting a valve on the manifold base, N.C. and N.O. can be reversed by the function plate orientation. Also, since the cylinder operates in reverse, confirm if the function plate is correctly mounted or not. N.C. specification N.O. specification Changing from N.C. to N.O. This product is delivered as N.C. valve. If N.O. valve is required, remove mounting screws of the required valve and turn over the function plate. (Make sure that there are gaskets on both sides of the plate.) Then, tighten the mounting screws to fix the valve to the manifold base. Port z Port x Port c Port positions for manifold solenoid valve body Function plate Figure: For N.C. Function plate Specifications N.C. N.O. Function plate No mark NO. Each valve is fixed to the manifold base with two M4 mounting screws. Tighten the screws firmly when re-mounting.. For mounting, tighten M4 or equivalent screws evenly into the mounting holes of the manifold base. Tightening torque of the mounting screw (M4):.4 N m Piping. For the common exhaust type, pressurization or evacuation of the (R) port can cause a malfunction. 8

11 Safety Instructions : Warning: Danger : indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of, Warning or Danger. They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC) ), and other safety regulations. ) ISO 444: Pneumatic fluid power General rules relating to systems. ISO 44: Hydraulic fluid power General rules relating to systems. IEC 6004-: Safety of machinery Electrical equipment of machines. (Part : General requirements) ISO 08-: Manipulating industrial robots Safety. etc. Warning. The compatibility of the product is the responsibility of the person who designs the equipment or decides its specifications. Since the product specified here is used under various operating conditions, its compatibility with specific equipment must be decided by the person who designs the equipment or decides its specifications based on necessary analysis and test results. The expected performance and safety assurance of the equipment will be the responsibility of the person who has determined its compatibility with the product. This person should also continuously review all specifications of the product referring to its latest catalog information, with a view to giving due consideration to any possibility of equipment failure when configuring the equipment.. Only personnel with appropriate training should operate machinery and equipment. The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced.. Do not service or attempt to remove product and machinery/ equipment until safety is confirmed.. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed.. When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any appropriate source is cut, and read and understand the specific product precautions of all relevant products carefully.. Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction. 4. Contact SMC beforehand and take special consideration of safety measures if the product is to be used in any of the following conditions.. Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight.. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping, vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or other applications unsuitable for the standard specifications described in the product catalog.. An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation.. The product is provided for use in manufacturing industries. The product herein described is basically provided for peaceful use in manufacturing industries. If considering using the product in other industries, consult SMC beforehand and exchange specifications or a contract if necessary. If anything is unclear, contact your nearest sales branch. Limited warranty and Disclaimer/ Compliance Requirements The product used is subject to the following Limited warranty and Disclaimer and Compliance Requirements. Read and accept them before using the product. Limited warranty and Disclaimer. The warranty period of the product is year in service or.5 years after the product is delivered, whichever is first. ) Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch.. For any failure or damage reported within the warranty period which is clearly our responsibility, a replacement product or necessary parts will be provided. This limited warranty applies only to our product independently, and not to any other damage incurred due to the failure of the product.. Prior to using SMC products, please read and understand the warranty terms and disclaimers noted in the specified catalog for the particular products. ) Vacuum pads are excluded from this year warranty. A vacuum pad is a consumable part, so it is warranted for a year after it is delivered. Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty. Compliance Requirements. The use of SMC products with production equipment for the manufacture of weapons of mass destruction (WMD) or any other weapon is strictly prohibited.. The exports of SMC products or technology from one country to another are governed by the relevant security laws and regulations of the countries involved in the transaction. Prior to the shipment of a SMC product to another country, assure that all local rules governing that export are known and followed. Safety Instructions Be sure to read Handling Precautions for SMC Products (M-E0-) before using. Akihabara UDX 5F, 4-4-, Sotokanda, Chiyoda-ku, Tokyo 0-00, JAPAN Phone: Fax: SMC Corporation All Rights Reserved Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. D-G st printing QW printing QW 850SZ Printed in Japan.

12 Port Solenoid Valve Direct Operated Poppet Type Series VT7 Rubber Seal [Option] Compact yet provides a large flow capacity Dimensions (W x H x D) 45 x 89.5 x 45 (Grommet) C:.6 dm /(s bar) (Passage ) Suitable for use in vacuum applications 0. kpa (For vacuum specifications: VT/VO7V) A single valve with 6 valve functions (Universal porting type) Selective porting can provide 6 valve functions, such as N.C. valve, N.O. valve, Divider valve, Selector valve etc. V T T 0 7 G 0 Body type Body ported Manifold Valve option Nil Standard type E Continuous duty type V For vacuum Option Rated voltage 00 VAC, Hz 00 VAC, Hz 0 VAC, Hz 4 0 VAC, Hz 5 4 V 6 V 7 40 VAC, Hz 9 Other Option How to Order Thread type Nil F N T CE-compliant Rc G NPT NPTF Nil Q CE-compliant Electrical entry: D/DO only Port size Nil Without port (For manifold) 0 4 (8A) VV06 V00 S070 VQD VKF VK VT VS JIS Symbol G H C T D Electrical entry Grommet, 00 mm lead wire Grommet, 600 mm lead wire Conduit Conduit terminal DIN terminal Light/Surge voltage suppressor Electrical entry G H C T D Symbol Nil Note) S Note) Z Note) S: With surge voltage suppressor Note) Refer to the figure below. Z: With light/surge voltage suppressor As to the case of rated voltage [Others (9)], please contact SMC. Surge voltage suppressor mounting part (For G ) Surge voltage suppressor Manifold Model VO7(-Q) Applicable manifold type Common or individual exhaust Accessory O-ring (P0, 4 pcs.) Note) Bolts (M4 x 0.7 x 0, pcs.) Note) It is not applied to Continuous duty type. Refer to the accessories on page

13 Series VT7 Flow Characteristics/Mass Standard Specifications Type of actuation Fluid Operating pressure range Ambient and fluid temperature Response time () Max. operating frequency Lubrication Mounting orientation Shock/Vibration resistance () Enclosure Electrical entry rated voltage (V) Allowable voltage fluctuation Apparent power () Power consumption () Light/Surge voltage suppressor (Not applicable for grommet type) AC (50/60 Hz) Inrush AC Holding AC Direct operated type position single solenoid Air 0 to 0.9 MPa 0 to 50 C (No freezing. Refer to page 5.) 0 ms or less (at the pressure of 0.5 MPa) 0 Hz Not required (Use turbine oil Class ISO VG, if lubricated.) Non-locking push type Unrestricted 50/50 m/s Dustproof Grommet, Conduit, Conduit terminal, DIN terminal 00, 00, 0, 0, 40 4, 5 to +0% of rated voltage 9 VA (50 Hz), 6 VA (60 Hz) VA (50 Hz), 7 VA (60 Hz) Without indicator light: 6 W, With indicator light: 6. W Varistor, Neon bulb Varistor, LED (Neon bulb for 00 V or more) Option Note ) Based on dynamic performance test, JIS B ( temperature: 0 C, at rated voltage, without surge suppressor) Note ) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction and at the right angles to the main valve and armature in both energized and de-energized states every once for each condition. (Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Note ) At rated voltage Flow characteristics Valve model (P A) (A R) (R A) (A P) C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv VT7 VT7V (Vacuum spec. type) VT7E (Continuous duty type) Note) Values for a single valve unit. It differs in the manifold case. Refer to manifold specifications on page 6. Mass Grommet 0.9kg Option Continuous duty type: VT7E Exclusive use of VT7E is recommended for continuous duty with long time loading.. This model is for continuous duty, not for high cycle rates. But even in low cycle rates, if energizing the valve more than once a day, please consult with SMC.. Energizing solenoid should be done at least once in 0 days. Vacuum spec. type: VT7V This vacuum model has less air leakage than the standard model under low pressure. It is recommended for vacuum application.. Since this valve has slight air leakage, it can not be used for vacuum holding (including positive pressure holding) in the pressure container. Specifications different from standard are as follows. Operating pressure range 0. kpa to 0. MPa 60 Construction No. Description Body Spool valve De-energized Operation principles <De-energized> Spool valve w is pushed upward by the return spring e, port P is closed, and port A and port R are opened. Component Parts Material Note Aluminum die-casted Color: Platinum silver Aluminum, NBR Energized <Energized> When an electric current is applied to the molded coil r, the armature t is attracted to the core y, and through the push rod u, it pushes down the spool valve w. Then, port P and port A are connected. At this time, there will be gaps between the armature t and the core y, but the armature will be magnetically attracted to the core y.

14 Port Solenoid Valve Direct Operated Poppet Type Series VT7 Dimensions Grommet: VT7- G Conduit: VT7- C fitting position 4 positions per 90 ( 00 Note) (Lead wire length) fitting position 4 positions per 90 ( 80 (Lead wire length) x M6 mounting hole For top mounting (M4) x M6 mounting hole For top mounting (M4) ( positioning pin) ( positioning pin) x /4 x /4 x M6 x for bottom mounting Note) There is also ÒVT7- HÓ (Lead wire length: 600 mm). Conduit terminal: VT7- T DIN terminal: VT7- D x M6 x for bottom mounting VV06 V00 S070 VQD VKF VK VT VS fitting position 4 positions per 90 x M6 mounting hole For top mounting (M4) fitting position 4 positions per 90 x M6 mounting hole For top mounting (M4) x /4 ( positioning pin) x /4 x M6 x for bottom mounting ( positioning pin) Max.0 DIN terminal facing upward (0.6) x M6 x for bottom mounting Applicable cable O.D. 6 to 6

15 Series VT7 Manifold Specifications VT7 manifold is B mount style and available both as a common exhaust and individual exhaust model. VV A Common exhaust Individual exhaust VV VV VV7 Please indicate manifold base type, applicable manifold valve and blanking plate when ordering. Ordering example: VV A pc. (5-station manifold base) VO7-G 4 pcs. PVT7-5-A pc. (Blanking plate) Manifold Specifications How to Order Manifold A Manifold type Max. number of stations Applicable solenoid valve Exhaust port Symbol Type Common () Base type: /4 VT7 manifold Individual Valve stations 0 stations 0 0 stations Max. 0 P Base (Side) 4 ( 8 ) Base (Side) 4 Thread type Rc G NPT NPTF B mount 0 stations () VO7 - (-Q) () Port location (Direction)/Port size A Base (Side) 4 Base (Side) 4 Option A Mounting bracket R Base (Side) 4 ( 8 ) Base (Side) 4 Note ) For more than stations, supply air both sides of P port. The common exhaust type should exhaust from both of the R port. Note ) In the case of common exhaust type, R and P ports size can be Rc /8 by using a mounting adaptor. Note ) Can also be applied to Series VVT0 manifold. Nil F N T A port size (Base piping) /4 Symbol Symbol Passage P R Common Common Common exhaust type only Porting specifications A Side Common Individual Side Accessory for Applicable Solenoid Description O-ring Hexagon socket head screw Part no. P0 P0F Max. 0.7 x 0 Qty 4 Note Standard type vacuum specifications type Continuous duty type Option Description Blanking plate (With screw, O-ring) Mounting bracket (With screw) Part no. PVT7-5-A DXT (For common exhaust) Flow Characteristics/Mass Flow characteristics Valve model (P A) (A R) (R A) (A P) C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv VO7 VO7V (Vacuum spec. type) VO7E (Continuous duty type) Mass Grommet 0.kg 6

16 Port Solenoid Valve Direct Operated Poppet Type Series VT7 Dimensions: Common Exhaust (Interchangeable with VVT0 for mounting) Without mountingbracket: VV A single valve unit port location x 7 mounting hole P port A port R port n x /4 DIN terminal facing upward 6.6 Applicable cable O.D. 6 to 4 x /4 VV06 V00 S070 VQD L Dimension n: Stations VKF Stations L L L Formula L =46xn+9 L =46xn+4 VK VT With mountingadaptor: VV A 4 x 7 mounting hole VS n x /4 DIN terminal facing upward x /8 Applicable cable O.D. 6 to L Dimension n: Stations Stations L L L Formula L =46xn+89 L =46xn+59 6

17 Series VT7 Dimensions: Individual Exhaust Without mounting bracket/vv x 7 mounting hole Manual override Conduit (C) Grommet (G) Conduit terminal (T) DIN terminal (D) DIN terminal facing upward (6.6) n x /4 Applicable cable O.D. 6 to L Dimension L Stations L L n:stations Formula L =46xn+9 L =46xn+4 Precautions Be sure to read before handling. Refer to front matters 58 and 59for Safety Instructions and pages to 7 for /4/5 Port Solenoid Valve Precautions. Mounting Warning. When mounting valves on the manifold base, the mounting orientation is decided. If it is mounted in the wrong direction, connected equipment may malfunction. Mount it by referring to how to switch over from N.C. to N.O. specifications.. Each valve is fixed to the manifold base with two M4 mounting screws. Tighten the screws evenly when re-mounting. Tightening torque of the mounting screw (M4):.4 Nám. For mounting, tighten M4 or equivalent screws evenly into the mounting holes of the manifold base. Changing from N.C. to N.O. Universal porting permits convertibility N.C./N.O. by a simple 80 degree rotation. Mounting conditions for N.C. and N.O. is indicated as below figure. Exhaust port type Common exhaust Individual exhaust Valve N.C. * Changing from N.C. to N.O. This product is delivered as N.C. valve. If N.O. valve is needed, remove mounting screws of the required valve and turn the valve at 80 degrees. (Make sure that there are O-rings fixed on 4 positions of the valve surface.) Then, tighten the mounting screws to fix the valve to the manifold base. N.O. 64

18 Series VT7 Specific Product Precautions Be sure to read before handling. Refer to Front matters 58 and 59 for Safety Instructions and pages to 7 for /4/5 Port Solenoid Valve Precautions.. A bleed port for the main valve is located at the bottom of the solenoid valve. Since blocking it causes malfunction, do not block it. Ordinarily, when the solenoid valve is mounted on a metal surface, it can breathe through the breather hole, via the breather groove. However, in particular, if the surface to be mounted is made of the rubber, the rubber could deform and block the hole.. Make sure that dust and/or other foreign materials should not enter the valve from the unused port (e.g. exhaust port). Also, since there is a bleed port for the armature in the manual override, do not allow accumulation of dust and/or other foreign materials to block bleed port. Bleed air passage Manual override Bleed port of main valve AC Change of Electrical Entry Angle. Series VT7 can change electrical entry angle. (4 positions). How to change: Loosen the nut (), remove the coil () from the body assembly (), place the positioning pin (4) at the required place, put back the coil () to its place, and tighten sufficiently with lock nut (). Surge voltage suppressor (S) Light/Surge Voltage Suppressor Varistor Diode Grommet (G) Conduit (C) () () (4) () Conduit terminal (T) DIN terminal (D) Varistor Neon bulb VV06 V00 S070 VQD VKF VK VT VS AC Varistor Bottom of the solenoid valve How to Calculate the Flow Rate For obtaining the flow rate, refer to front matters 44 to 47. Light/Surge voltage suppressor (Z) None Varistor 48 V or less Protection circuit for light/surge voltage suppressor is not the polarity type. Varistor 00 V Neon bulb Lead Wire Color (Grommet) Voltage 00 VAC 00 VAC Other Color Blue Red Red (+), Black ( ) Gray Electrical Connection DIN terminal is connected inside as in the figure below. Connect to the corresponding power supply. Ground 65

19 Series VT7. Disassembly ) After loosening the thread (), then if the cover (4) is pulled in the direction of the thread, the connector will be removed from the body of equipment (solenoid, etc.). ) Pull out the screw (), then remove the gasket (a) or (b). ) On the bottom part of the terminal block (), there s a cut-off part (indication of an arrow) (a). If a small flat head screwdriver is inserted between the opening in the bottom, terminal block () will be removed from the cover (4). (Refer to graph at right.) 4) Remove the cable gland (5) and plain washer (6) and rubber seal (7).. Wiring ) Pass them through the cable (8) in the order of cable ground (5), washer (6), rubber seal (7), and then insert into the housing (4). ) Dimensions of the cable (8) are as shown in the right figure. Skin the cable and crimp the crimped terminal (9) to the edges. ) Remove the screw with washer (e) from the bracket (e). (Loosen in the case of Y-shape type terminal.) As shown in the right figure, mount a crimped terminal (9), and then again tighten the screw (e). Note) Tighten within the tightening torque of 0.5 N m ±5%. Note: a It is possible to wire even in the state of bare wire. In that case, loosen the screw with washer (e) and place a lead wire into the bracket (d), and then tighten it once again. b The maximum size for the round terminal (9) is.5 mm.5 and for the Y terminal is.5 mm 4. c Cable (8) external: ø6 to ø Note) For the one with the external external dimension ranged between ø9 to ø remove the inside parts of the rubber seal (7) before using.. Assembly ) Terminal box () connected with housing (4) should be reinstated. (Push it down until you hear the click sound.) ) Putting rubber seal (7), plain washer (6), in this order into the cable introducing slit on the housing (4), then further tighten the cable gland (5) securely. ) By inserting gasket (a) or (b) between the bottom part of the terminal box () and a plug on an equipment, screw in () on top of the housing (4) and tighten it. Note) Tighten within the tightening torque of 0.5 N m ±0%. Note: The orientation of a connector can be changed arbitrarily, depending on the combination of a housing (4) and a terminal box (). Comparison between the Product Model No. and the Part No. Note ) mark in the product model numbers denotes the rated voltage. Note ) mark denotes the valve option. Note ) mark and mark are for coil part number and coil assembly with terminal the rated voltage. Example ) In the case of VT7-00GB-05 Example ) In the case of PVT7-5G Note 4) In the case of CE-compliant products (-Q), coils are not shipped together. Product model no. VT/O7 - G(-0) VT/O7 - GS(-0) VT/O7 - H(-0) VT/O7 - HS(-0) VT/O7 - C(-0) VT/O7 - CS(-0) VT/O7 - T(-0) VT/O7 - TS(-0) VT/O7 - TZ(-0) VT/O7 - D(-0) VT/O7 - DS(-0) VT/O7 - DZ(-0) How to Use DIN Terminal no. PVT7-00GB- PVT7- G PVT7-00GB- L06 PVT7- G-06 PVT7-00CB- PVT7- C PVT7-00DB- PVT7-00DB- PVT7-00DB- Exploded view () (a) (d) (b) (e) (b) () (c) (9) (4) (a) (6) (7) (e) (9) (e) Magnifying figure Self-up screw assembly with terminal part no. PVT7-00TBT- PVT7-00TBTS- PVT7-00TBTZ- PVT7-00DBT- PVT7-00DBTS- PVT7-00DBTZ- When the rated voltage is AC and if it is assembled with the coil for, response may be delayed and occur malfunction. Also, for valves, when the coil for AC is assembled, it occurs malfunction. For AC valves, assemble the coil for AC, and for valves, assemble the coil for. (5) (8) Connector for DIN Terminal Rated voltage 00 VAC 00 VAC 4 V For other rated voltages, please consult with SMC. Without light/surge voltage suppressor (D) GDMA With surge voltage suppressor (DS) GDMA-S GDMA-S GDMA-S5 Light/Surge voltage suppressor (DZ) GDMA-Z GDMA-Z GDMA-Z5 66

20 Port Solenoid Valve Direct Operated Poppet Type Series VT5 Rubber Seal [Option] Compact yet provides a large flow capacity Dimensions (W x H x D) 55 x 8 x 5 (Grommet) C: 0.6 dm /(s bar) {Rc /8 (Passage )} A single valve with 6 valve functions (Universal porting type) Six valve functions can be attained by selecting the piping ports. (Enabling the N.C. valve, N.O. valve, divider valve, selector valve, etc. to be used as desired.) Suitable for use in vacuum applications 0. kpa (For vacuum specifications type: VT/VO5V) VT5- T JIS Symbol VT5- C VT5- D VT5- G VT5 For manifold: Enter VO. Valve option Nil V Option Manifold Standard For vacuum Port size 4 8 Without connection port (For manifold) Model VO5-00 (-Q) Specifications Type of actuation Fluid Operating pressure range Ambient and fluid temperature Max. operating frequency Response time () Lubrication Shock/Vibration resistance () Enclosure 0 G Nil Q CE-compliant Electrical entry: D/DO/DL/DLO only Surge voltage suppressor Nil None With surge voltage suppressor AC: Can be attached to Grommet, Conduit, S Conduit terminal. : Can be attached to Grommet, Conduit, Conduit terminal. Direct operated type position single solenoid Air 0 to.0 MPa 5 to 50 C 5 Hz 0 ms or less (at the pressure of 0.5 MPa) Not required (Use turbine oil Class ISO VG, if lubricated.) Non-locking push type 50/50 m/s Dustproof Note ) Based on dynamic performance test, JIS B ( temperature: 0 C, at rated voltage, without surge suppressor) Note ) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction and at the right angles to the main valve and armature in both energized and de-energized states every once for each condition. (Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Solenoid Specifications Electrical entry rated voltage Allowable voltage fluctuation Apparent power () Power consumption () Note ) At rated voltage Rated voltage 00 VAC, 50/60 Hz 00 VAC, 50/60 Hz 0 VAC, 50/60 Hz 4 0 VAC, 50/60 Hz 5 4 V 6 V 7 40 VAC, 50/60 Hz 9 Other Option How to Order Applicable manifold B mount common exhaust type AC Inrush Holding 50 Hz 60 Hz 50 Hz 60 Hz Nil M Electrical entry G C D T TL DL Non-locking type Locking type (Tool required) Grommet, Lead wire length 00 mm Conduit DIN terminal Conduit terminal Terminal with indicator light DIN terminal with indicator light Thread type Nil F N T Accessory Gasket (DXT08--) Bolts (DXT08-9-, pcs.) Grommet, Conduit, DIN terminal, Conduit terminal 00, 00 VAC, 50/60 Hz, 4 V 5 to +0% of rated voltage 75 VA 60 VA 7 VA 7 VA W Rc G NPT NPTF CE-compliant For the coil rated voltage (option ), please contact SMC. VV06 V00 S070 VQD VKF VK VT VS 67

21 Series VT5 Flow Characteristics/Mass Valve model Flow characteristics Port size (P A) (A R) (R A) (A P) C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv / VT5 VT5V (Vacuum spec. type) VT5 VT5V (Vacuum spec. type) / Note) Values for a single valve unit. It differs in the manifold case. Refer to manifold specifications on page 60. Mass Grommet 0.55 kg (For AC) 0.60 kg (For ) Option. For vacuum Pressure range 0. kpa to 0. MPa This vacuum model has less air leakage than the standard model under low pressure. It is recommended for vacuum application. ) Since this valve has slight air leakage, it can not be used for holding vacuum (including positive pressure holding) in the pressure container.. With surge voltage suppressor, with indicator light Surge Voltage Suppressor Grommet (GS) Conduit (CS) Conduit terminal (TS) Circuit for Indicator Light DIN terminal with indicator light (DL) Conduit terminal with indicator light (TL) Grommet type Varistor Neon bulb Surge voltage suppressor AC AC Varistor Neon bulb Red (+) ( ) Black Diode Varistor Construction No. De-energized o Retainer Operation principle <De-energized> The spool e is pushed upward by the force of the spring r and the air passage between port x and port c is opened and port z is blocked. Air flow direction: z Block, x c Component Parts Description Body Cover Spool valve Material Aluminum die-casted Aluminum die-casted Aluminum, NBR u Plunger w Cover y i Over travel assembly q Body e Spool valve t O-ring r Spool spring Note Platinum silver Platinum silver Energized <Energized> When the coil y is energized the plunger u is pulled down depressing the spool e via the overtravel assembly i and the air passage between port z and port x is opened and port c is blocked. Air flow direction: z x, c Block. with lock ) Using a screwdriver, push the manual override button that is located in the head portion of the solenoid valve in order to directly push the spool valve downward, thus causing the valve to switch. ) With the button remaining pushed down, turn it approximately 90 clockwise or counterclockwise to maintain the manual override locked state. ) To revert to the original state, keep the button pushed down and turn it approximately 90 clockwise. 68

22 Port Solenoid Valve Direct Operated Poppet Type Series VT5 Dimensions Grommet (G) Conduit (C) x mounting groove Lead wire length 80 x mounting groove 00 x Rc /4, /8 Width across flats x Rc /4, /8 Width across flats VV06 V00 S070 x ø4.5 mounting hole VQD VKF DIN terminal (D) Conduit terminal (T) VK Connector Applicable cable O.D. ø6 to ø VT VS x mounting groove x mounting groove x Rc /4, /8 Width across flats x Rc /4, /8 Width across flats With locking manual override Conduit terminal with indicator light (TL) Light 9. (With locking type manual override) x mounting groove x Rc /4, /8 Width across flats 69

23 Series VT5 Manifold Specifications Series VT5 Manifold Model has a B mount style with common exhaust. Common exhaust VVT Porting specifications Symbol P 0 Side Side How to Order Manifold Manifold Specifications Manifold type Max. number of stations Applicable solenoid valve Exhaust port type Common Option A Side Bottom 0 7 R Side Side Valve stations stations 7 stations Port size Symbol Port size Exhaust port type Common exhaust Port location/port size P A R Base Base Base 4, 8 4, 8 4, 8 Instruct by specifying the valves and blanking plate to be mounted on the manifold along with the manifold base model no. <Example> VVT40-05 pc. VO5-00G 4 pcs. DXT08-A pc. B mount 7 stations Note) VO5-00 (-Q) P Side Blanking plate (With gasket, screw) Thread type Port direction A Side/Bottom DXT08-A Note) If there are more than 4 stations, supply air from both P ports and exhaust from both R ports. Nil F N T Rc G NPT NPTF R Side Accessory for Applicable Description Part no. Qty. Manifold gasket DXT08-- pc. Hexagon socket head screw DXT08-9- pcs. Flow Characteristics/Mass VO5 Valve model VO5V (Vacuum spec. type) Flow characteristics (P A) (A R) (R A) (A P) C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv Mass Grommet 0.58 kg (For AC) 0.6 kg (For ) Warning When mounting valves on the manifold base, the mounting orientation is decided. If it is mounted in the wrong direction, connected equipment may malfunction. Mount it by referring to external dimensions on page 6. Besides, the external dimensions are showing the case of N.C. specifications. Precautions Changing from N.C. to N.O. The valves are assembled as N.C. valves at the time of shipment. By removing the two retaining screws from the desired valves, and rotating each valve body 80 and reassembling it on the manifold base, it is possible to reassemble an N.C. valve as an N.O. valve. (When doing so, make sure that a gasket is attached to the mounting surface of the valve.) Properly tighten the screws. The tightening torque of the retaining screws is N m. 60

24 Port Solenoid Valve Direct Operated Poppet Type Series VT5 Dimensions Common exhaust Pitch x ø9 mounting hole Conduit DIN terminal (T) Grommet (G) terminal (D) Conduit (C) 4 x Rc /4, /8 Max. For bottom ported n x Rc /4, /8 Bottom ported Pitch A single valve unit port location VV06 V00 Blanking plate Port () A, Port () S070 VQD Pitch n x Rc /4, /8 Symbol L L n Formula: L = 46n + 9, L = 46n Port () n: Stations VKF VK VT VS 6

25 Series VT5 Specific Product Precautions Be sure to read before handling. Refer to front matters 58 and 59 for Safety Instructions and pages to 7 for /4/5 Port Solenoid Valve Precautions.. The bottom of the solenoid valve has a breather hole for the main valve. Take proper measures to prevent this hole from being blocked as this will lead to a malfunction. Ordinarily, when the solenoid valve is mounted on a metal surface, it can breathe through the breather hole, via the breather groove. However, in particular, if the surface to be mounted is made of the rubber, the rubber could deform and block the hole. Bleed groove Grommet Bleed port on main valve Bottom of the solenoid valve. Make sure that dust and/or other foreign materials do not enter the valve from the unused port (e.g. exhaust port). The grommet portion contains a breather hole for the core. Take proper measures to prevent dust or foreign matter from accumulating in this area. Electrical Connection For wiring to DIN terminal, connect the positive (+) polar side with connector terminal no. and the negative ( ) side with connector terminal no. when the rated voltage is type. How to Calculate the Flow Rate For obtaining the flow rate, refer to front matters 44 to 47.. Disassembly ) After loosening the thread (), then if the cover (4) is pulled in the direction of the thread, the connector will be removed from the body of equipment (solenoid, etc.). ) Pull the screw (), and then remove gasket (a) or (b). ) On the bottom part of the terminal block (), there s a cut-off part (indication of an arrow) (a). If a small flat head screwdriver is inserted between the opening in the bottom, terminal block () will be removed from the cover (4). (Refer to the figure below.) 4) Remove the cable gland (5) and plain washer (6) and rubber seal (7).. Wiring ) Pass them through the cable (8) in the order of cable ground (5), washer (6), rubber seal (7), and then insert into the housing (4). ) Dimensions of the cable (8) are the figure as below. Skin the cable and crimp the crimped terminal (9) to the edges. ) Remove the screw with washer (e) from the bracket (e). (Loosen in the case of Y shape type terminal.) As shown in the below figure, mount a crimped terminal (9), and then again tighten the screw (e). Note) Tighten within the tightening torque of 0.5 N m ±5%. Note: a It is possible to wire even in the state of bare wire. In that case, loosen the screw with washer (e) and place a lead wire into the bracket (d), and then tighten it once again. b The maximum size for the round terminal (9) is.5 mm.5 and for the Y terminal is.5 mm 4. c Cable (8) external: ø6 to ø Note) For the one with the external dimension ranged between ø9 to ø remove the inside parts of the rubber seal (7) before using. How to Wire DIN Terminal. Assembly ) Terminal box () connected with housing (4) should be reinstated. (Push it down until you hear the click sound.) ) Putting rubber seal (7), plain washer (6), in this order into the cable introducing slit on the housing (4), then further tighten the cable gland (5) securely. ) By inserting gasket (a) or (b) between the bottom part of the terminal box () and a plug on an equipment, screw in () on top of the housing (4) and tighten it. Note) Tighten within the tightening torque of 0.5 N m ±0%. Note: The orientation of a connector can be changed arbitrarily, depending on the combination of a housing (4) and a terminal box (). Exploded view (d) (d) () (a) (e) (b) () (c) (4) (9) (a) (6) (7) (e) (e) (9) Magnifying figure Self-up screw (5) (8) Connector for DIN Terminal Description DIN connector Part no. GDMC 6