TRILUX _Trilux_23_Title_GB.indd :30:56 Uhr

Transcription

1 TRILUX 23

2

3 Downlights and spotlights 004 Ambiella Free-standing and wall-mounted luminaires Dialog Eco Surface-mounted and suspended luminaires F Atirion Recessed luminaires 032 Cetrix 034 Solis Luminaires with high protection ratings Oleveon High bay luminaires and batten luminaires 042 RaptorPlus 044 Ridos Photometric data tables Download at or in the Service section. 1

4 Quality and Price Both Impressive. Nowadays light is required constantly and everywhere. That s why our luminaires must always be ready to operate anywhere. Each individual luminaire is subject to fulfilling that requirement regardless of the version and price. This claim provides the impetus for each and every employee working at TRILUX, which currently employs 5000 persons world-wide. Cost-effective light means more than just low costs of acquisition. Are the utilised technologies efficient? Have they been used optimally? Are the operating costs low? These are prerequisites upon which we at TRILUX are constantly focusing and for which we strive to offer solutions and set standards. Moreover, we provide you with tested and inspected electrical, thermal and mechanical safety with our ENECcertified products. Guaranteed.

5 To utilise light correctly, one must think about many things. Even if a room is bright, it does not mean it is lit well. The installation must be simple, upkeep and maintenance should be efficient in both time and cost. And optimal light quality is usually achieved through tailored lighting technology and proper planning. After all, only perfectly utilised light is able to deliver perfect results. Once these prerequisites are fulfilled, the result may be called light from TRILUX. Or: New Light.

6 Ambiella Downlights with highly-specular aluminium reflector 654da IP Joule 850 C + Covers underside IP44 Recommended areas Entrance areas, corridors, conference rooms, cafeterias, lounges, hotels, restaurants and residential areas. Optical system Highly-specular reflector, made of high-purity post-anodised aluminium, for narrow/wideangle light distribution. Luminaire body Bezel ring made of sheet steel, galvanised, powder-coated white, securely connected with reflector. Ceiling recess mounting by means of rapid-mounting springs. Control gear options E With electronic control gear. K With low-loss inductive ballasts, parallel-compensated. L With low-loss inductive ballasts. E EB3h Emergency light version with electronic control gear and individual battery in the gear tray made of galvanised sheet steel. Nominal operation time 3 hours. 4

7 Ambiella C HR Ambiella C HR + DA-TM Ambiella C HR + DA-M-PC Reference TOC Control gear option Lamps Recess kg opening (mm) E K L W Ambiella C HR 1TCD x TC-D(EL) Ambiella C HR 1TCD x TC-D(EL) Ambiella C HR 1TCD x TC-D(EL) Ambiella C HR 1TCD18 EB3h x TC-D(EL) Ambiella C HR 1TCD26 EB3h x TC-D(EL) Ambiella C HR 2TCD x TC-D(EL) Ambiella C HR 2TCD x TC-D(EL) Ambiella C HR 2TCD x TC-D(EL) Ambiella C HR 2TCD18 EB3h x TC-D(EL) Ambiella C HR 2TCD26 EB3h x TC-D(EL) Accessories TOC Description kg Ambiella DA-TM Cover consisting of float glass, partly-frosted 0.9 Ambiella DA-M-PC Cover made of polycarbonate, frosted 0.6 Ambiella C HR 2TCD18 UTE: 0.58 C DIN 5040: A50 CIBSE: BZ 2 NBN L : BZ 3 Ambiella C-HR

8 Serie 664, 717 Wall-mounted luminaires for mirror lighting 654da IP Joule 650 C 7171 M IP C/ C/TC / /TC18 Application Wall-mounted luminaires for mirror lighting, available with switch and/or socket : Safety class II. Optical system Opal PLEXIGLAS diffuser, made in one piece with internal channel prisms. Luminaire body 6641 Extruded aluminium, powder-coated, white. White-coated end caps or in version C chrome-finished end caps made of diecast aluminium, subtly inclined at the front plane Glass-fibre reinforced polyester, grey, with internal reflector made of white polyester, safety class II, protected against the ingress of water. Control gear option E With electronic control gear. K With low-loss inductive ballasts, parallel-compensated. L With low-loss inductive ballasts. 6

9 7171/ /18 Reference TOC Control Lamps D D1 E1 E2 IP kg gear option E K L W mm 6641/TC x TC-L C/TC x TC-L / x C/ x / x C/ x / x C/ x / x / x

10 Dialog Free-standing luminaires Eco S 654da IP Joule 960 C Recommended areas For commercial office lighting. Especially recommended for VDU workstations. Luminaire Direct/indirect free-standing luminaire, consisting of luminaire head, stand profile and stand foot. Stand profile, rectangular crosssection, and stand foot made of steel, silvergrey, similar to RAL Stand foot with central recess. Optical system Direct/indirect, with perforated optics for direct light component. Direct light component with internal light-scattering membrane for uniform illumi-nation of the perforated design. Suitable for VDU applications in accordance with EN due to low luminance L 1000 cd/m 2 at critical angles above 65 in all planes. Luminaire head Luminaire head made of sheet steel, arcshaped, with integral direct optics, fine perforation, and die-cast end caps. 01 White. 03 Silver-grey, similar to RAL Electrical connection With mains cable to be ordered separately (depending on country). Control gear options E With electronic control gear and switches for on/off. ED With dimmable electronic control gear with 1-10 V interface and multi-function push-button for on/off and dimming. EDS With dimmable electronic control gear and lighting management system with integral presence detection. Additionally with multifunction push-button for on/off, dimming and light control 8

11 Dialog Eco S 01 Dialog Eco S 03 Reference TOC Control gear options Lamps Dimensions Colour kg L x W x H E ED EDS W mm Dialog Eco S 4TCL x TC-L x 365 x 198 White 12.0 Dialog Eco S 4TCL x TC-L x 365 x 198 Silver-grey 12.0 Accessories*TOC Description ZALW/2500 EU Mains cable, black, length 2500 mm, for Germany and other European countries ZALW/2500 GB Mains cable, black, length 2500 mm, for Great Britain * Mains cables for other countries on request. Dialog Eco S 4TCL55 UTE: 0.05 D T DIN 5040: E03 CIBSE: BZ 4/2.5/BZ 5 NBN L : BZ 4 Dialog Eco S

12 Series 1330 F Surface-mounted luminaires with opal PLEXIGLAS diffuser 654da IP Joule 650 C PC 0,5 Joule 850 C 1330 F/ O Application Offices, sales areas, showrooms, lounges and corridors. Optical system PLEXIGLAS trapezium-shaped diffuser, made in one piece, stable and torsionally rigid. Safe retention of the diffuser by means of internal spring clips. Opal diffuser with fine-grained matt surface. PC Diffuser made of polycarbonate. Luminaire body Powder-coated sheet steel, white, slim profile. End caps made of impact-resistant ABS. Reference TOC Control Lamps D D1 D2 E1 E2 kg gear option E K W mm 1330 F/136 O x F/158 O x F/236 O x F/258 O x F/136 O-PC x F/158 O-PC x F/236 O-PC x F/258 O-PC x Control gear option E With electronic control gear. K With low-loss inductive ballasts, parallel-compensated F/158 O UTE: 0.61 G T DIN 5040: B31 CIBSE: BZ 5 NBN L : BZ F/ O 1284/36W, 1584/58W O 1279/36W, 1578/58W O-PC 10

13 Series 1330 F Surface-mounted luminaires with prismatic diffuser 654da IP Joule 650 C PC 0,5 Joule 850 C 1330 F/ P Application Offices, sales areas, showrooms, lounges and corridors. Optical system PLEXIGLAS trapezium-shaped diffuser, made in one piece, stable and torsionally rigid. Safe retention of the diffuser by means of internal spring clips. Photometrically effective prisms to direct the light primarily onto the working plane. PC Diffuser made of polycarbonate. Reference TOC Control Lamps D D1 D2 E1 E2 kg gear option E K W mm 1330 F/136 P x F/158 P x F/236 P x F/258 P x F/136 P-PC x F/158 P-PC x F/236 P-PC x F/258 P-PC x Luminaire body Powder-coated sheet steel, white, slim profile. End caps made of impact-resistant ABS. Control gear option E With electronic control gear. K With low-loss inductive ballasts, parallel-compensated F/158 P UTE: 0.72 G T DIN 5040: B30 CIBSE: BZ 5 NBN L : BZ F/ P 1284/36W, 1584/58W P 1279/36W, 1578/58W P-PC 11

14 Series 5261 Suspended and surface-mounted luminaires with reflection-intensifying, highly-specular parabolic louvre RPX 654da IP Joule 650 C with PC end caps 850 C 5261 RPX Application Offices, sales areas, showrooms and financial institutions. Universal application as suspended luminaires and with overhead reflectors and fixing accessories also as surface-mounted luminaires. Optical system Micro-segmented, highly-specular parabolic louvre RPX made of reflection-intensifying aluminium with a surface purity of % for especially high light output. Suitable for VDU applications in accordance with EN due to low luminance L 1000 cd/m 2 at critical angles above 65 in all planes. Louvre retention by means of spring-tensioned clips, providing earth continuity. Louvre can be lowered and hung from either side without tools. Light distribution Direct/indirect, indirect component approx. 45%. With perforated overhead reflectors: indirect component approx. 15 %. With closed overhead reflectors: indirect component 0% RPX-L/49 UTE: 0.47 B T DIN 5040: C63 CIBSE: BZ 2/1.5/BZ 1 NBN L : BZ RPX-L/ DG/1500 UTE: 0.66 B T DIN 5040: B63 CIBSE: BZ 2/0.75/BZ 1 NBN L : BZ 1 Luminaire body Slender and elegant luminaire profile, upper profile arched towards the ceiling, made of solvent-free powder-coated sheet steel, white. With integral coupling brackets for noninterrupted continuous lines. End caps to be ordered separately RPX-L/ DR/1500 UTE: 0,75 B DIN 5040: A60 CIBSE: BZ 2/1.5/BZ 1 NBN L : BZ 1 Control gear option Versions /28/54 and 35/49/80 in Multi-Lamp technology allows the operation of T5 lamps in different wattages. E With electronic control gear. ED With dimmable electronic control gear with 1-10 V interface. 12

15 Accessories RPX Reference TOC Control Lamps D D1 D2 D3 D4 kg gear option E ED W mm 5261 RPX-L/28/ x 28/ , RPX-L/35/49/ x 35/49/ , RPX-L/2x28/ x 28/ , RPX-L/2x35/ x 35/ , RPX-L/2x x , End caps for individual luminaires or for the completion of continuous lines to be ordered separately. Accessories for TOC Description surface mounting SN Wire suspension 1 m, 1 piece SN/2m Wire suspension 2 m, 1 piece Accessories for TOC Description surface mounting AB Ceiling spacer, 1 pair, in combination with overhead reflector DR/ Overhead reflector, closed, for /28/ DR/ Overhead reflector, closed, for /35/49/ DG/ Overhead reflector, perforated, for /28/ DG/ Overhead reflector, perforated, for /35/49/ RPX RPX D3 D2 D3 D2 D4 13

16 Series 5261 Suspended and surface-mounted luminaires with reflection-intensifying, semi-specular parabolic louvre RSX 654da IP Joule 650 C with PC end caps 850 C 5261RSX Application Offices, sales areas, showrooms and financial institutions. Universal application as suspended luminaires and with overhead reflectors and fixing accessories also as surface-mounted luminaires. Optical system Micro-segmented, semi-specular parabolic louvre RSX made of reflection-intensifying aluminium with a surface purity of % for especially high light output. Suitable for VDU applications in accordance with EN due to low luminance L 1000 cd/m 2 at critical angles above 65 in all planes. Louvre retention by means of spring-tensioned clips, providing earth continuity. Louvre can be lowered and hung from either side without tools. Light distribution Direct/indirect, indirect component approx. 45%. With perforated overhead reflectors: indirect component approx. 15 %. With closed overhead reflectors: indirect component 0% RSX-L/49 UTE: 0.47 B T DIN 5040: C63 CIBSE: BZ 2/1/BZ 1 NBN L : BZ RSX-L/ DG/1500 UTE: 0.65 B T DIN 5040: B63 CIBSE: BZ 2/1/BZ 1 NBN L : BZ 1 Luminaire body Slender and elegant luminaire profile, upper profile arched towards the ceiling, made of solvent-free powder-coated sheet steel, white. With integral coupling brackets for noninterrupted continuous lines. End caps to be ordered separately RSX-L/ DR/1500 UTE: 0.75 B DIN 5040: A60 CIBSE: BZ 2 NBN L : BZ 1 Control gear option Versions /28/54 and 35/49/80 in Multi-Lamp technology allows the operation of T5 lamps in different wattages. E With electronic control gear. ED With dimmable electronic control gear with 1-10 V interface. 14

17 Accessories RSX Reference TOC Control Lamps D D1 D2 D3 D4 kg gear option E ED W mm 5261 RSX-L/28/ x 28/ , RSX-L/35/49/ x 35/49/ , RSX-L/2x28/ x 28/ , RSX-L/2x35/ x 35/ , RSX-L/2x x , End caps for individual luminaires or for the completion of continuous lines to be ordered separately. Accessories for TOC Description surface mounting SN Wire suspension 1 m, 1 piece SN/2m Wire suspension 2 m, 1 piece Accessories for TOC Description surface mounting AB Ceiling spacer, 1 pair, in combination with overhead reflector DR/ Overhead reflector, closed, for /28/ DR/ Overhead reflector, closed, for /35/49/ DG/ Overhead reflector, perforated, for /28/ DG/ Overhead reflector, perforated, for /35/49/ RSX RSX D3 D2 D3 D2 D4 15

18 Series 5261 Suspended and surface-mounted luminaires with semi-specular parabolic louvre RMV 654da IP Joule 650 C with PC end caps 850 C 5261 RMV Application Offices, sales areas, showrooms and financial institutions. Universal application as suspended luminaires and with overhead reflectors and fixing accessories also as surface-mounted luminaires. Optical system Micro-segmented parabolic louvre RMV made of semi-specular anodised aluminium with a surface purity of %. Suitable for VDU applications in accordance with EN due to low luminance L 1000 cd/m 2 at critical angles above 65 in all planes. Louvre retention by means of spring-tensioned clips, providing earth continuity. Louvre can be lowered and hung from either side without tools. Light distribution Direct/indirect, indirect component approx. 45 %. With perforated overhead reflectors: indirect component approx. 15 %. With closed overhead reflectors: indirect component 0 % RMV-L/49 UTE: 0.42 B T DIN 5040: C53 CIBSE: BZ 3/0.75/ BZ 2 NBN L : BZ RMV-L/ DG/1500 UTE: 0.58 B T DIN 5040: B53 CIBSE: BZ 2 NBN L : BZ 2/1.5/BZ 1/4/BZ 4 Luminaire body Slender and elegant luminaire profile, upper profile arched towards the ceiling, made of solvent-free powder-coated sheet steel, white. With integral coupling brackets for noninterrupted continuous lines. End caps to be ordered separately. Control gear option Versions /28/54 and 35/49/80 in Multi-Lamp technology allows the operation of T5 lamps in different wattages. E With electronic control gear. ED With dimmable electronic control gear with 1-10 V interface RMV-L/ DR/1500 UTE: B DIN 5040: A60 CIBSE: BZ 2 NBN L : BZ 2/0.8/BZ 1 16

19 Accessories RMV Reference TOC Control Lamps D D1 D2 D3 D4 kg gear option E ED W mm 5261 RMV-L/28/ x 28/ , RMV-L/35/49/ x 35/49/ , RMV-L/2x28/ x 28/ , RMV-L/2x35/ x 35/ , RMV-L/2x x , End caps for individual luminaires or for the completion of continuous lines to be ordered separately. Accessories for TOC Description surface mounting SN Wire suspension 1 m, 1 piece SN/2m Wire suspension 2 m, 1 piece Accessories for TOC Description surface mounting AB Ceiling spacer, 1 pair, in combination with overhead reflector DR/ Overhead reflector, closed, for /28/ DR/ Overhead reflector, closed, for /35/49/ DG/ Overhead reflector, perforated, for /28/ DG/ Overhead reflector, perforated, for /35/49/ RMV RMV D3 D2 D3 D2 D4 17

20 Series 5261 Suspended and surface-mounted luminaires with semi-specular cross-blade louvre RSV 654da IP Joule 650 C with PC end caps 850 C 5261 RSV Application Offices, sales areas, showrooms and financial institutions. Universal application as suspended luminaires and with overhead reflectors and fixing accessories also as surface-mounted luminaires. Optical system Micro-segmented louvre RSV made of highpurity anodised aluminium, with graduated concave-profiled cross blades, for narrow/ wide-angle light distribution. Louvre retention by means of spring-tensioned clips, providing earth continuity. Louvre can be lowered and hung from either side without tools. Light distribution Direct/indirect, indirect component approx. 45%. With perforated overhead reflectors: indirect component approx. 15 %. With closed overhead reflectors: indirect component 0% RSV-L/58 UTE: 0.46 C T DIN 5040: B53 CIBSE: BZ 3 NBN L : BZ RSV-L/ DG/1550 UTE: 0.53 C T DIN 5040: B53 CIBSE: BZ 1 NBN L : BZ 3/1.5/BZ 2/4/BZ3 Luminaire body Slender and elegant luminaire profile, upper profile arched towards the ceiling, made of solvent-free powder-coated sheet steel, white. With integral coupling brackets for noninterrupted continuous lines. End caps to be ordered separately. Control gear option Versions /28/54 and 35/49/80 in Multi-Lamp technology allows the operation of T5 lamps in different wattages. E With electronic control gear ED With dimmable electronic control gear with 1-10 V interface RSV-L/ DR/1550 UTE: 0.54 C DIN 5040: A50 CIBSE: BZ 1 NBN L : BZ 3/.8/BZ 2 18

21 Accessories RSV Reference TOC Control Lamps D D1 D2 D3 D4 kg gear option T5 E ED W mm 5261 RSV-L/28/ x 28/ , RSV-L/35/49/ x 35/49/ , T RSV-L/ x , RSV-L/ x , End caps for individual luminaires or for the completion of continuous lines to be ordered separately. Accessories for TOC Description surface mounting SN Wire suspension 1 m, 1 piece SN/2m Wire suspension 2 m, 1 piece Accessories for TOC Description surface mounting AB Ceiling spacer, 1 pair, in combination with overhead reflector DR/ Overhead reflector, closed, for /28/ DR/ Overhead reflector, closed, for /35/49/ DR/ Overhead reflector, closed, for / DR/ Overhead reflector, closed, for / DG/ Overhead reflector, perforated, for /28/ DG/ Overhead reflector, perforated, for /35/49/ DG/ Overhead reflector, perforated, for / DG/ Overhead reflector, perforated, for / RSV RSV D3 D2 1281/36W 1583/58W 1227/28W/54W 1527/35W/49W/80W 1281/36W 1583/58W 1227/28W/54W 1527/35W/49W/80W D3 D2 D4 1281/36W 1583/58W 1192/28W/54W 1492/35W/49W/80W 1281/36W 1583/58W 1192/28W/54W 1492/35W/49W/80W 19

22 Series 5261 Suspended and surface-mounted luminaires with white louvre RWV 654da IP Joule 650 C with PC end caps 850 C 5261 RWV Application Offices, sales areas and showrooms. Universal application as suspended luminaires and with overhead reflectors and fixing accessories also as surface-mounted luminaires. Optical system Micro-segmented louvre RWV made of aluminium, white, for a uniform light distribution. Louvre retention by means of spring-tensioned clips, providing earth continuity. Louvre retention by means of spring-tensioned clips, providing earth continuity. Louvre can be lowered and hung from either side without tools. Light distribution Direct/indirect, indirect component approx. 45 %. With perforated overhead reflectors: indirect component approx. 15 %. With closed overhead reflectors: indirect component 0 % RWV-L/49 UTE: 0.44 D T DIN 5040: C43 CIBSE: BZ 2/2.5/BZ 3 NBN L : BZ RWV-L/ DG/1500 UTE: 0.64 D T DIN 5040: B53 CIBSE: BZ 2/4/BZ 3 NBN L : BZ 3 Luminaire body Slender and elegant luminaire profile, upper profile arched towards the ceiling, made of solvent-free powder-coated sheet steel, white. With integral coupling brackets for noninterrupted continuous lines. End caps to be ordered separately. Control gear option Versions /28/54 and 35/49/80 in Multi-Lamp technology allows the operation of T5 lamps in different wattages. E With electronic control gear. ED With dimmable electronic control gear with 1-10 V interface RWV-L/49 E DR/1500 UTE: 0.72 D DIN 5040: A50 CIBSE: BZ 2/1.25/BZ 3 NBN L : BZ 3 20

23 Accessories RWV Reference TOC Control Lamps D D1 D2 D3 D4 kg gear option T5 E ED W mm 5261 RWV-L/28/ x 28/ , RWV-L/35/49/ x 35/49/ , T RWV-L/ x , RWV-L/ x , End caps for individual luminaires or for the completion of continuous lines to be ordered separately. Accessories for TOC Description suspended mounting SN Wire suspension 1 m, 1 piece SN/2m Wire suspension 2 m, 1 piece Accessories for TOC Description suspended mounting AB Ceiling spacer, 1 pair, in combination with overhead reflector DR/ Overhead reflector, closed, for /28/ DR/ Overhead reflector, closed, for /35/49/ DR/ Overhead reflector, closed, for / DR/ Overhead reflector, closed, for / DG/ Overhead reflector, perforated, for /28/ DG/ Overhead reflector, perforated, for /35/49/ DG/ Overhead reflector, perforated, for / DG/ Overhead reflector, perforated, for / RWV RWV D3 D2 1281/36W 1583/58W 1227/28W/58W 1527/35W/49W/80W 1281/36W 1583/58W 1227/28W/58W 1527/35W/49W/80W D3 D2 D4 1281/36W 1583/58W 1192/28W/58W 1492/35W/49W/80W 1281/36W 1583/58W 1192/28W/58W 1492/35W/49W/80W 21

24 Series 5261 Accessories KA A 03 D A 03 S Geometrical arrangement mm 3284 mm End-cap adapter 1 piece, white, for the connection of nodes A 03, with 5-conductor through-wiring set 1.5 mm KA KA-PC* * Polycarbonate is suitable for increased preventive fire protection. ** Incoming cables are not supplied. They must be provided by the installing contractor. Ceiling node 1 piece, for up to four junctions, continuously adjustable between 90 and 270. Die-cast aluminium, white. A 03 D Node with wire suspension 1 piece, consisting of: 1 node as described in A 03 D, 1 steel wire for suspension lengths of up to 1.5 m, 1 ceiling fixing unit. A 03 S Ceiling rose** (not illustrated) 1 piece, for the connection of the mains cable AN Counter-balance weight Required for mounting to node A 03 S A Order example: Geometrical arrangement as per the diagram above with 4 luminaires 5261 RPX-L/35/49/80 E and 2 luminaires 5261 RPX-L/28/54 E, wire suspensions, 5LV through-wiring set: 4 luminaires 5261 RPX-L/35/49/80 E 2 luminaires 5261 RPX-L/28/54 E 8 end-cap node adapters KA 6 counter-balance weights A20 4 nodes with wire suspensions A 03 S 2 wire suspensions SN 1 ceiling rose AN 1 feeding tube ZR/2m 4 through-wiring sets 3700/5LV/58 1 through-wiring set 3700/5LV/ DR DG Closed overhead reflector Solvent-free powder-coated sheet steel. For purely downward direct light distribution of surface-mounted and suspended luminaires. Easy attachment to luminaire body and potential equalisation by means of screw connection DR/1200 for /28/ DR/1500 for /35/49/ DR/1250 for / DR/1550 for / Perforated overhead reflector Solvent-free powder-coated sheet steel. To increase the direct component of suspended luminaires or for decorative ceiling lighting with surface-mounted luminaires. Easy attachment to luminaire body and potential equalisation by means of screw connection DG/1200 for /28/ DG/1500 for /35/49/ DG/1250 for / DG/1550 for /

25 5261 K AB SN DBS End cap 1 pair, for front-plane finish of individual or continuous-line luminaires. Plastic, white. To be attached without using tools K K-PC* Ceiling rose** (not illustrated) 1 piece, for the connection of the mains cable in case of ceiling outlets A Ceiling spacer 1 pair, plastic material, necessary for direct surface ceiling mounting, distance between upper luminaire edge and ceiling: 18 mm AB Wire suspension** 1 piece, for suspended mounting of 5261 luminaires, consisting of: 1 ceiling fixing bracket, galvanised steel, 1 steel wire, 1.0 mm, 2 luminaire fixing clamps, 1 plastic ceiling trim cap, white SN For suspension lengths of up to 1.0 m SN/2m For suspension lengths of up to 2.0 m. Wiring connection unit** for mains feeding for SN, SN/2m, consisting of necessary strain relief systems, fixing screws and connection terminal 4 x2.5 mm 2. 1 set. Without incoming cable ESBN Ceiling fixing rails Sheet steel, white. To cover the mains cable for surface mounting. Only necessary for ceiling outlets located at the longitudinal luminaire axis outside the front-plane feeding opening of the luminaires. Additional ceiling spacers AB are not required DBS/1200 for /28/ DBS/1500 for /35/49/ DBS/1250 for / DBS/1550 for / Wiring cover (not illustrated) 1 piece, plastic material, to cover the mains cable in case of direct ceiling surface mounting LK P ZR PLEXIGLAS prismatic cover 1 piece, can be attached without tools. To protect the lamp and the optical system against unnecessarily rapid degradation. Only for suspended mounting P/1200 for /28/ P/1500 for /35/49/ P/1250 for / P/1550 for / Feeding tube** 1 piece, plastic, white, 10 mm, to be shortened on site. To guide and cover the mains cable ZR m long, in combination with SN ZR/2m m long, in combination with SN/2m or A 03 S with AN. Through-wiring sets Colour-coded, heat-resistant individual cables 1.5 mm 2. 3LV 3-conductor through-wiring. 5LV 5-conductor through-wiring. Reference for L TOC luminaires mm 3700/3LV/36 28/54, /5LV/36 28/54, /3LV/58 35/49/80, /5LV/58 35/49/80, /5LV/25m L 25 m

26 Atirion Surface-mounted luminaires with semi-specular cross-blade louvre RSV or semi-specular parabolic louvre RPV 654da IP Joule 850 C RPV Atirion D-L RSV Recommended areas Offices, sales areas and showrooms. RPV Especially recommended for VDU workstations as well. Optical system Direct. RSV Micro-segmented louvre made of high-purity anodised aluminium, with graduated concave-profiled cross blades, for narrow/ wide-angle light distribution. RPV Micro-segmented parabolic louvre made of highly-specular anodised aluminium with a surface purity of %. Suitable for VDU applications in accordance with EN due to low luminance L 1000 cd/m 2 at critical angles above 65 in all planes. Louvre retention by means of spring-tensioned clips, providing earth continuity. Louvre can be lowered and hung from either side without tools. Atirion D-L RSV 158 UTE: 0.64 C DIN 5040: A50 CIBSE: BZ 1 NBN L : BZ 3/1.5/BZ 2/4/BZ 3 Atirion D-L RPV 158 UTE: 0.65 B DIN 5040: A50 CIBSE: BZ 2 NBN L : BZ 2/ 2/BZ 1/2.5/BZ 2/3/B Luminaire body Sheet steel, white, powder-coated, 75 mm height overall. Slimline design, with underside angled at 55. L Luminaires as continuous-line version End caps for individual luminaires or continuous lines to be ordered separately. Control gear option E With electronic control gear. ED With dimmable electronic control gear with 1-10 V interface. K With low-loss inductive ballasts, parallelcompensated. 24

27 Accessories 29 Atirion D-L RPV Reference TOC Control gear option Lamps kg E ED K W Atirion D-L RSV 136 * x Atirion D-L RSV 158 * x Atirion D-L RSV 236 * x Atirion D-L RSV 258 * x Atirion D-L RPV 136 * x Atirion D-L RPV 158 * x Atirion D-L RPV 236 * x Atirion D-L RPV 258 * x * End caps for individual luminaires or for the completion of continuous lines to be ordered separately. See page 29. Atirion D-L 25

28 Atirion Surface-mounted luminaires with white louvre RWV or semi-specular parabolic louvre RMV 654da IP Joule 850 C RMV Atirion D-L RWV Recommended areas Offices, sales areas and showrooms. RMV Especially recommended for VDU workstations as well. Optical system Direct. RWV Micro-segmented louvre made of aluminium, white, for a uniform light distribution. RMV Micro-segmented parabolic louvre made of semi-specular anodised aluminium with a surface purity of %. Suitable for VDU applications in accordance with EN due to low luminance L 1000 cd/m 2 at critical angles above 65 in all planes. Louvre retention by means of spring-tensioned clips, providing earth continuity. Louvre can be lowered and hung from either side without tools. Atirion D-L RWV 158 UTE: 0.68 D DIN 5040: A50 CIBSE: BZ 2/3/BZ 3 NBN L : BZ 3 Atirion D-L RMV 158 UTE: 0.59 C DIN 5040: A50 CIBSE: BZ 1 NBN L : BZ 2 Luminaire body Sheet steel, white, powder-coated, 75 mm height overall. Slimline design, with underside angled at 55. L Luminaires as continuous-line version End caps for individual luminaires or continuous lines to be ordered separately. Control gear option E With electronic control gear. ED With dimmable electronic control gear with 1-10 V interface. K With low-loss inductive ballasts, parallelcompensated. 26

29 Accessories 29 Atirion D-L RMV Reference TOC Control gear option Lamps kg E ED K W Atirion D-L RWV 136 * x Atirion D-L RWV 158 * x Atirion D-L RWV 236 * x Atirion D-L RWV 258 * x Atirion D-L RMV 136 * x Atirion D-L RMV 158 * x Atirion D-L RMV 236 * x Atirion D-L RMV 258 * x * End caps for individual luminaires or for the completion of continuous lines to be ordered separately. See page 29. Atirion D-L 27

30 Atirion Surface-mounted luminaires with wall-washer optics RAV Accessories da IP Joule 850 C Atirion D-L RAV Recommended areas Offices, sales areas and showrooms. Optical system Direct. Wall-washer reflector RAV for asymmetrical light distribution. Highly-specular reflector made of anodised, high-purity aluminium. Reference TOC Control gear option Lamps kg E ED K W Atirion D-L RAV 136 * x Atirion D-L RAV 158 * x * End caps for individual luminaires or for the completion of continuous lines to be ordered separately. See page 29. Luminaire body Sheet steel, white. powder-coated, 75 mm.height overall Slimline design, with underside angled at 55. L Luminaires as continuous-line version End caps for individual luminaires or continuous lines to be ordered separately. Atirion D-L RAV 158 UTE: 0.62 E DIN 5040: A40 CIBSE: BZ 4 NBN L : BZ 4 Control gear option E With electronic control gear. ED With dimmable electronic control gear with 1-10 V interface. K With low-loss inductive ballasts, parallelcompensated. Atirion D-L 28

31 Atirion Accessories Wire suspensions 1 piece Y-wire suspension ZST/1000* TOC for suspension lengths up to 1000 mm ZST/2000* TOC for suspension lengths up to 2000 mm 1 piece 4-point wire suspension (not illustrated) ZS/1000* TOC for suspension lengths up to 1000 mm ZS/2000* TOC for suspension lengths up to 2000 mm *2 pieces necessary per individual luminaire. ZST/ Ceiling rose 1 piece, for the connection of the mains cable in case of ceiling outlets. ZAA/01 TOC piece, circular, white ZAE/01 TOC piece, square, white ZA /01 End caps 1 pair of polycarbonate end caps for both ends of the luminaire. ZKS PC TOC pair Through-wiring sets (not illustrated) Special wiring sets for the subsequent installation in luminaires equipped with electronic control gear. Through-wiring for versions with magnetic ballasts available on request. ZKS PC Heat-resistant, colour-coded individual wires, 1.5 mm². 3LV 3-conductor through-wiring. 5LV 5-conductor through-wiring. 3700/3LV/36 TOC Through-wiring 3 x 1.5 mm 2 for 36 W 3700/5LV/36 TOC Through-wiring 5 x 1.5 mm 2 for 36 W 3700/3LV/58 TOC Through-wiring 3 x 1.5 mm 2 for 58 W 3700/5LV/58 TOC Through-wiring 5 x 1.5 mm 2 for 58 W Wiring connection unit (not illustrated) 1 piece, for mains supply with ZS or ZST, consisting of necessary strain relief systems, fixing screws and connection terminal. ZESB TOC piece Counter-balance weights (not illustrated) Necessary for single-lamp luminaires with low-loss ballast ( K) and single- and twin-lamp luminaires with electronic control gear ( E, ED) for mounting to wire suspensions ZST A10 TOC for 136 K A11 TOC for 158 K A12 TOC for 136 E/ED, 158 E/ED, 236 E, 258 E A28 TOC for 236 ED, 258 ED 29

32 Series 740 Anti-tamper, anti-ligature surface-mounted luminaires q54da IP40 10 Joule 850 C Product description Ceiling- and wall-mounted anti-tamper and anti-ligature, suitable for foyers, stairwells, corridors, lounges, bedrooms, mental health units and areas subject to vandalism. Optical system Circular opal polycarbonate diffuser in spherical form. Safe retention of the diffuser by bayonet fixing and secondary deco ring fixed to the primary ring by anti-tamper screws. Luminaire body Solvent-free powder-coated sheet steel finished white. Solvent-free powder-coated deco-ring, white. Control gear option E With electronic control gear (E). Other electrical versions available on request. 30

33 Reference TOC Control Lamps D E1 E2 kg gear option E W mm 7401NPC-ATL/2xTC x TC-SEL NPC-ATL/2xTCD x TC-DEL PC-ATL/1xTCF x TCF PC-ATL/2xTCF x TCF PC-ATL/1xTCF36 +TC x TCF x TC-SEL PC-ATL/2xTCF36 +TC x TCF x TC-SEL N PC-ATL/ 2xTCD13 UTE: 0.34 H T DIN 5040: B31 CIBSE: BZ 6 NBN L : BZ 6 Vandal resistance The polycarbonate diffuser of the 740 antiligature series luminaires provides a high degree of mechanical strength and is particularly suitable for use in areas subject to vandalism E1 160 E2 E 31

34 Cetrix RMV, RPV 65d IP Joule 960 C Recommended areas Offices, sales areas, showrooms, and financial institutions. Especially recommended for VDU workstations as well. Universal luminaire system for ceilings with concealed and exposed grids with 600 mm module, and for cut-out recess openings. Optical system RPV Highly-specular parabolic louvre made of aluminium with a surface purity of %. RMV Micro-segmented parabolic louvre made of semi-specular anodised aluminium with a surface purity of %. Suitable for VDU applications in accordance with EN due to low luminance L 1000 cd/m 2 at critical angles above 65 in all planes. Luminaire body Of square design, made of white sheet steel. Supplied ready for connection, with three-pole connection options for mains supply and further wiring up to 2.5 mm². Control gear options E With electronic control gear. 32

35 Cetrix 600 RPV Cetrix 600 RMV Reference TOC Control Lamps Module Recess kg gear option opening E W mm mm Cetrix 600 RMV x x Cetrix 600 RMV x x Cetrix 600 RPV x x Cetrix 600 RPV x x Accessories (not illustrated) TOC Description Cetris ZBB set fixing brackets Cetrix 600 RPV 414 E UTE: 0.77 B DIN 5040: A50 CIBSE: BZ 1 NBN L : BZ 2 Cetrix 600 RMV 314 E UTE: 0.70 B DIN 5040: A50 CIBSE: BZ 1 NBN L : BZ 2 Cetrix

36 Solis Recessed luminaires with double-reflection system 654da IP Joule 850 C RPX / RSX Recommended areas Recommended for offices, conference rooms, sales areas, financial institutions and other circulation areas. RPX / RSX especially recommended for VDU workstations. For ceilings with exposed grids. Solis M73 For 600 mm module. Optical system Double-reflection system made of sheet steel, white. PSS Primary optical system consisting of micro-perforated sheet steel for wide-angle, pleasantly uniform light distribution. RPX Primary optical system consisting of micro-segmented, highly-specular parabolic louvre RPX made of reflection-intensifying aluminium with a surface purity of % for especially high light output. Suitable for VDU applications in accordance with EN due to low luminance L 1000 cd/m² at critical angles above 65 in all planes. RSX Primary optical system consisting of micro-segmented, semi-specular parabolic louvre RSX made of reflection-intensifying aluminium with a surface purity of % for especially high light output. Suitable for VDU applications in accordance with EN due to low luminance L 1000 cd/m² at critical angles above 65 in all planes. RWV Primary optical system consisting of micro-segmented louvre made of aluminium, white, for a uniform light distribution. Luminaire body Sheet steel, white. Gear tray made of galvanised sheet steel. Control gear option E With electronic control gear. ED With dimmable electronic control gear with 1-10 V interface. 34

37 Solis M73 PSS Solis M73 RSX Solis M73 RWV Reference TOC Control Lamps Module kg gear option E ED mm PSS Solis M73 PSS 2TCL x TC-L Solis M73 PSS 2TCL x TC-L Solis M73 PSS 2TCL x TC-L RPX-PSOW Solis M73 RPX-PSOW 1TCL x TC-L Solis M73 RPX-PSOW 1TCL x TC-L Solis M73 RPX-PSOW 2TCL x TC-L Solis M73 RPX-PSOW 2TCL x TC-L Solis M73 RPX-PSOW x Solis M73 RPX-PSOW x Solis M73 RPX-PSOW x Solis M73 RPX-PSOW x RSX-PSOW Solis M73 RSX-PSOW 1xTCL x TC-L Solis M73 RSX-PSOW 1xTCL x TC-L Solis M73 RSX-PSOW 2xTCL x TC-L Solis M73 RSX-PSOW 2xTCL x TC-L Solis M73 RSX-PSOW x Solis M73 RSX-PSOW x Solis M73 RSX-PSOW x Solis M73 RSX-PSOW x RWV-PSOW Solis M73 RWV-PSOW 1xTCL x TC-L Solis M73 RWV-PSOW 1xTCL x TC-L Solis M73 RWV-PSOW 2xTCL x TC-L Solis M73 RWV-PSOW 2xTCL x TC-L Solis M73 RWV-PSOW x Solis M73 RWV-PSOW x Solis M73 RWV-PSOW x Solis M73 RWV-PSOW x Solis M73 PSS 2TCL55 E UTE: 0.45 E DIN 5040: A40 CIBSE: BZ 5/1.5/BZ 4 NBN L : BZ 5/4/BZ 4 Solis M73 RSX- PSOW 214 UTE: 0.77 D DIN 5040: A50 CIBSE: BZ 3 NBN L : BZ 3 Solis M73 RWV- PSOW 414 UTE: 0.69 D DIN 5040: A50 CIBSE: BZ 3 NBN L : BZ 3 Solis M

38 Serie 719 Weather-proof surface-mounted luminaires 654dM IP65 0,2 Joule 850 C 719 D / o$ 0,5 Joule Application Damp or corrosive environments, and covered exterior areas. Versions without reflector suitable for damp and wet environments with general illumination requirements, e.g., boiler-houses and greenhouses. Optical system Batten luminaire with reflector accessories. DSR Parabolic reflector system with PC cover, tiltable +/ 45, and integral specular reflector. 7191/58 UTE: 0.57 H T DIN 5040: B21 CIBSE: BZ 6 NBN L : BZ 6 Luminaire body Glass-fibre reinforced polyester resin, very low flammability, light-grey. With fitting end feed and grommets for mains supply. Further wiring, central feed or continuousline arrangements by means of internal wiring accessory 07191/4LV/. D Suitable for production sites subject to fire hazards due to low surface temperatures and high IP rating. Version with impact-resistant lamp protection tube and equipped as standard with electronic control gear (E) because of higher thermal safety requirements. 7191/ R/58 UTE: 0.85 G DIN 5040: A30 CIBSE: BZ 5 NBN L : BZ 6/1.5/BZ 5 Control gear option E With electronic control gear. K With low-loss inductive ballasts, parallelcompensated Reflector 07190R 1 piece, solvent-free powder-coated sheet steel, white. Universally suitable for single- and twin-lamp 719 luminaires E1 E2 E3 E E E E E1 E2 E3 E E E E D1 D 660 D1 D 660 E E1 E2 E3 E E D1 D 1265/36W 1565/58W 36

39 R R 7191 DSR Reference TOC Control Lamps kg Reference TOC D D1 E1 E2 E3 kg** gear option E K L W Reflector* mm 7191/ x R/ / x R/ / x R/ / x R/ / x R/ / x R/ D/ x R/ D/ x R/ D/ x R/ D/ x R/ DSR/ x DSR/ x * Reflector to be ordered separately. ** Weight including reflector. Accessories TOC Description Internal wiring, for continuous lines and in case of central feeding 07191/4LV/ For luminaires /36, 1.5 mm², with 2 terminal blocks 07191/4LV/ For luminaires /58, 1.5 mm², with 2 terminal blocks Steel strip suspension 75N pair, 1 m, stainless steel V2A, with luminaire fixing brackets R 7191 DSR 70 E1 E2 E3 E E E E E E1 E2 E3 E E E 224 D1 D D1 D 660 E E1 E2 E3 E E D1 D 1265/36W 1565/58W 37

40 Oleveon T5 Weather-proof surface-mounted luminaires 654da IP Joule 650 C E o$ PC 6 Joule 850 C TW840 IP65 Oleveon 1 Oleveon 2 TW 840 Recommended areas Ceiling- and wall-mounted luminaires for standard use in damp or corrosive environments and covered exterior areas. Optical system PLEXIGLAS diffuser, smooth clear exterior surface, with internal prisms and fine-grained front planes, made in one piece. Safe retention of the diffuser by means of rocker fasteners made of glass-fibre reinforced polyamide. S With symmetrical reflector. PC Polycarbonate diffuser, smooth clear impact-resistant exterior surface, with internal prisms and fine-grained front planes, made in one piece. Recommended for increased mechanical stability. Luminaire body Glass-fibre reinforced polyester resin, very low inflammability, light-grey. Gear tray can be hung without using tools. Multiple front-plane knock-out openings for mains supply and further wiring. Additional ceiling-oriented feeding options. Grommets are enclosed loose. INOX Safe retention of the diffuser by means of V2A stainless steel rocker fasteners. Oleveon 149 UTE: 0.64 H T DIN 5040: B20 CIBSE: BZ 6 NBN L : BZ 6 Oleveon 2-135/49/80 S UTE: 0.86 G T DIN 5040: A30 CIBSE: BZ 6 NBN L : BZ 5 Production sites exposed to fire hazards Due to low surface temperatures and high IP rating, the versions are E suited for use in areas subject to fire hazards. Control gear option Versions /14/24, /28/54 and 35/49/80 in Multi-Lamp technology allow operation of T5 lamps with different wattages. E With electronic control gear. TW 840 TWIST version. Rapid-mounting luminaire with removabled 3-pole connection systems integrated in the front plane of the luminaire, complete with used fluorescent lamps 4000 K (840). Oleveon D L 38

41 Reference TOC Control Lamps L D kg gear options Single-lamp width, 1 lamp E W mm mm Oleveon 114/ x 14/ Oleveon 128/ x 28/ Oleveon 135/49/ x 35/49/ Oleveon 114/24 INOX x 14/ Oleveon 128/54 INOX x 28/ Oleveon 135/49/80 INOX x 35/49/ Oleveon 114/24 PC x 14/ Oleveon 128/54 PC x 28/ Oleveon 135/49/80 PC x 35/49/ Oleveon 180 PC TW x Oleveon 114/24 PC INOX x 14/ Oleveon 128/54 PC INOX x 28/ Oleveon 135/49/80 PC INOX x 35/49/ Single-lamp width, 2 lamp Oleveon x Oleveon x Oleveon x Oleveon x Oleveon x Oleveon x Oleveon PC x Oleveon PC x Oleveon PC x Oleveon PC x Oleveon PC x Oleveon PC x Twin-lamp width, 1 lamp with specular reflector Oleveon 2-128/54 S x 28/ Oleveon 2-135/49/80 S x 35/49/ Oleveon 2-128/54 S PC x 28/ Oleveon 2-135/49/80 S PC x 35/49/ Twin-lamp width, 2 lamps Oleveon x Oleveon x Oleveon x Oleveon x Oleveon x Oleveon 214 INOX x Oleveon 228 INOX x Oleveon 235 INOX x Oleveon 235/49 INOX x 35/ Oleveon 249 INOX x Oleveon 254 INOX x Oleveon 214 PC x Oleveon 228 PC x Oleveon 235 PC x Oleveon 249 PC x Oleveon 254 PC x Oleveon 235 PC TW x Oleveon 249 PC TW x Oleveon 214 PC INOX x Oleveon 228 PC INOX x Oleveon 235 PC INOX x Oleveon 235/49 PC INOX x 35/ Oleveon 249 PC INOX x Oleveon 254 PC INOX x Accessories TOC Description Internal wiring accessories for continuous lines and central feeding 5 colour-coded individual wires, 1.5 mm 2, with 2 connection terminals. Oleveon ZLV 5 x For luminaires 28, 54 W Oleveon ZLV 5 x For luminaires 35, 49, 80 W Stainless steel rocker fasteners Made of rust-proof and acid-resistant stainless steel (V2A) for the subsequent installation in case of increased requirements Oleveon Z-INOX For luminaires 14, 24 W (6 pcs.) Oleveon Z-INOX For luminaires 28, 54 W (8 pcs.) Oleveon Z-INOX For luminaires 35, 49, 80 W (10 pcs.) 39