H45 LED - Direct and indirect pendant

Transcription

1 RAL IP V 50/60Hz Specifications Direct and indirect light pendant linear luminaire. Aluminium profile. Diffusers in frosted polycarbonate profile. Driver included. Supplied with clear base, power supply cable and 2000 mm long steel suspension cables. With the separate circuits, direct and indirect lighting can be activated individually The single circuit activates direct and indirect lighting at the same time. Standard accessories No. 6 plastic wall plugs A2 stainless steel DIN 7505 B 4.5 mm (width) x 40 mm (length) screws Steel suspension cables, with mounting parts. Available wattages 39W 59W 78W Page 1/5

2 1st step Switch off mains supply; 2nd step Marking the anchorage locations; Drill attachment holes; 3rd step Remove the end caps; 3 4th step Remove the support profile; 5th step Fitting the cover; (front view) 6th step Fitting the cover; (side view) Connect the power wires; 7th step Attachment of the 2nd suspension cable; 8th step Remove diffusers; Page 2/5

3 9th step Remove upper wiring strip from inside the luminaire; Connect the luminaire to the mains wiring 10th step Replace upper wiring strip inside the luminaire; 11th step Mount suspensions from the ceiling to the luminaire; 12th step Detail of suspension part; (For linear systems see 15th step) Steel cable (suspension) Bracket Note: This part can be moved horizontally to adjust the position of the suspension cables. Height regulator Unlocked Locked 13th step Fitting the diffusers; (For linear systems see 1st step6) 14th step Luminaire installed. Page 3/5

4 Linear systems 15th step (to be performed after 12th step) The connection plate must be used to join the luminaire sections; 1st step6 (to be performed after 13th step) Apply 2 light blocking plates to the profile connection, on the upper and lower parts; Page 4/5

5 General conditions Installation/Maintenance The installation and maintenance of the different products must be performed by a qualified professional. The installation conditions described in the installation instructions and the operating conditions mentioned in the product datasheet must be duly guaranteed. Osvaldo Matos cannot be held liable for the incorrect assembly, installation, maintenance, repair or handling of its products. Osvaldo Matos cannot be held liable for unsuitable fittings. Osvaldo Matos cannot be held liable for product alteration or for instalation instructions not being duly followed. O/M products are prepared for installation in areas with ambient temperatures between 0ºC and 35ºC. Osvaldo Matos recommends that any false ceilings intended for the placement of recessed products should only be erected after the products to be mounted have been chosen. The same applies for the opening of slots to mount this type of product. Osvaldo Matos recommends reinforcing the ceiling close to the Mounting cutout according to the product characteristics. Performance The performance of the product will only be guaranteed if its handling, use, installation and maintenance are performed according to the supplied instructions. Power values in products with LED Light Source may have a 10% variation on the indicated value. Flux indicated for LED systems is a mean value, for Tj=25 C. Photometry results are obtained by testing a standard product of each range, in the laboratory under ideal conditions. Sales conditions All electrical components included in the products are of high quality. Warranty O/M products have a 3-year warranty from the delivery date for any proven construction or manufacturing defects, provided the transport conditions, installation conditions described in the installation instructions and the operating conditions mentioned in the product datasheet are duly guaranteed. Parts and components requiring replacement due to normal wear are excluded from this warranty. The products must be installed and maintained by qualified personnel in accordance with the accompanying instructions, and they cannot be altered or repaired without the prior written permission of Osvaldo Matos. Osvaldo Matos must be formally notified of any defect that is found and covered by the warranty. Osvaldo Matos decides whether to repair and/ or replace the product for the same or an equivalent product, subject to the changes arising from the technological evolution of the manufacturing process at that time, unless another solution is imposed by mandatory law. Returned products will only be accepted within 10 days of their delivery, and only for manufacturing defects that are confirmed by the factory, unless another conditions are stipulated by mandatory law. Hence, we recommend that products are checked on delivery. Page 5/5