SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z ALLTITE, INC Murdock, Wichita, KS Bruce Demaree Phone:

Transcription

1 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z ALLTITE, INC Murdock, Wichita, KS Bruce Demaree Phone: CALIBRATION Valid To: September 30, 2016 Certificate Number: In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following calibrations 1 : I. Electrical DC/Low Frequency Parameter/Equipment Range CMC 2 (±) Comments DC Voltage Generate 3 (0 to 320) mv (0.32 to 3.2) V (3.2 to 32) V (32 to 320) V (320 to 1050) V mv V V V 0.14 V DC Current Generate 3 (0 to 320) µa 320 µa to 3.2 ma (3.2 to 32) ma (32 to 320) ma 320 ma to 3.2 A (3.2 to 10.5) A µa 0.53 µa ma 0.06 ma 2.2 ma 12 ma Resistance Generate 3 (0 to 40) Ω (40 to 400) Ω (400 to 4000) Ω (40 to 400) kω (400 to 4000) kω (4 to 40) MΩ (40 to 400) MΩ 0.33 Ω 0.37 Ω 0.79 Ω 120 Ω 7.7 kω 330 kω 1.4 MΩ (A2LA Cert. No ) 10/09/2014 Page 1 of 6

2 Parameter/Range Frequency CMC 2 (±) Comments AC Voltage Generate 3 (0 to 10) mv AC 0.45 mv 0.61 mv 1.1 mv 2.2 mv 5.9 mv (10 to 32) mv AC 0.39 mv 0.2 mv 0.48 mv 0.7 mv 1.6 mv (32 to 320) mv AC 0.32 mv 0.51 mv 0.6 mv 0.9 mv 2.2 mv 320 mv AC to 3.2 V AC 3.8 mv 89 mv 95 mv 21 mv 59 mv (3.2 to 32) V AC 0.12 V V V 0.16 V 0.46 V (32 to 105) V AC 0.15 V 0.22 V 0.28 V 0.33 V (105 to 320) V AC (40 to 100) Hz 100 Hz to 1 khz (1 to 3) khz 2.6 V 1.3 V 1.4 V (A2LA Cert. No ) 10/09/2014 Page 2 of 6

3 Parameter/Range Frequency CMC 2 (±) Comments AC Voltage Generate (cont) (320 to 800) V AC (40 to 100) Hz 100 Hz to 1 khz (1 to 3) khz 4.8 V 3 V 3.1 V 3.1 V (800 to 1050) V AC (40 to 100) Hz 100 Hz to 1 khz (1 to 3) khz 6.2 V 4 V 4 V 4.1 V AC Current Generate 3 (0 to 32) µa AC 1.2 µa 3.5 µa 13 µa 27 µa (32 to 320) µa AC 1.3 µa 3.3 µa 12 µa 25 µa 320 µa to 320 ma AC 0.56 ma 1.1 ma 1.7 ma 2.5 ma 320 ma to 3.2 A AC 5.8 ma 48 ma (3.2 to 10.5) A AC 41 ma 0.15 A (10.5 to 20) A AC A 0.39 A (0 to 20) A AC (100 to 440) Hz 0.37 A 0.53 A w/ 10 turn (20 to 100) A AC (10 to 100) Hz (100 to 440) Hz 0.72 A 1.5 A w/ 10 turn (100 to 150) A AC (10 to 100) Hz 0.8 A w/ 50 turn (A2LA Cert. No ) 10/09/2014 Page 3 of 6

4 Parameter/Range Frequency CMC 2 (±) Comments AC Current Generate (cont) (150 to 1000) A AC (10 to 100) Hz 4.2 A w/ 50 turn II. Mechanical Parameter/Equipment Range CMC 2 (±) Comments Torque Manual Torque Wrenches 3 (2 to 20) in lbf (20 to 200) in lbf ft lbf ISO 6789:2003 Manually applied and measured with a transducer (50 to 500) ft lbf ft lbf (500 to 2000) ft lbf 1.9 ft lbf Hydraulic Torque Wrenches 3 (500 to 5000) ft lbf (2000 to ) ft lbf 9 ft lbf ft lbf Hydraulic pressure measured and compared to torque measured by transducers ( to ) ft lbf 43 ft lbf (A2LA Cert. No ) 10/09/2014 Page 4 of 6

5 Parameter/Equipment Range CMC 2 (±) Comments Pneumatic Torque Gun 3 (0 to 5000) ft lbf 3.2 ft lbf Pneumatic pressure set and torque measured with transducer Electronic Torque Gun 3 (0 to 5000) ft lbf 3.2 ft lbf Digital torque set and torque measured with torque transducers Torque Multiplier 3 (0 to 2000) ft lbf (output) 14 ft lbf Input and output torque measured with torque transducers Torque Transducers (2 to 2000) ft lbf 0.28 ft lbf % ft lbf Torque arm with weights (1000 to ) ft lbf 4.6 ft lbf % ft lbf Pressure 3 Hydraulic Gauges (0 to 300) psig (300 to 3000) psig 0.19 psig psig Comparison with standard hydraulic pressure gage (3001 to ) psig 4.8 psig + 32 ( to ) psig 60 psig III. Time & Frequency Parameter/Equipment Range CMC 2 (±) Comments Frequency Measuring 0.5 Hz to 10.0 MHz 5.8 khz Equipment 3 1 This laboratory offers commercial calibration service and field calibration service. 2 Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement (A2LA Cert. No ) 10/09/2014 Page 5 of 6

6 that a laboratory can achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMCs represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory may be greater than the CMC due to the behavior of the customer s device and to influences from the circumstances of the specific calibration. 3 Field calibration service is available for this calibration and this laboratory meets A2LA R104 General Requirements: Accreditation of Field Testing and Field Calibration Laboratories for these calibrations. Please note the actual measurement uncertainties achievable on a customer's site can normally be expected to be larger than the CMC found on the A2LA Scope. Allowance must be made for aspects such as the environment at the place of calibration and for other possible adverse effects such as those caused by transportation of the calibration equipment. The usual allowance for the actual uncertainty introduced by the item being calibrated, (e.g. resolution) must also be considered and this, on its own, could result in the actual measurement uncertainty achievable on a customer s site being larger than the CMC. (A2LA Cert. No ) 10/09/2014 Page 6 of 6

7 A2LA has accredited ALLTITE, INC Wichita, KS for technical competence in the field of Calibration This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This laboratory also meets the requirements of ANSI/NCSL Z and any additional program requirements in the field of calibration. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 9 th day of October President & CEO For the Accreditation Council Certificate Number Valid to September 30, 2016 For the calibrations to which this accreditation applies, please refer to the laboratory s Calibration Scope of Accreditation.