SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005

Transcription

1 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 MGA RESEARCH CORPORATION 820 Suburban Park Drive Greer, SC Jennifer Young Phone: (864) Website: MECHANICAL Valid Until: May 31, 2017 Certificate Number: In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following tests on material level components (plastics, foams, fabrics, and composites), seating systems, instruments panels, glove boxes, storage doors, steering columns, floor and overhead consoles, auto/manual shifter, doors, door panels, windows, hoods, liftgates, decklids/trunks, swing metal components, roof systems, closure systems, structural components and other interior and exterior components for the automotive industry and other transportation-related industries including aerospace, rail, train, bus, and defense: Test Description/Parameter Airbag Deployment BMW PR Custom Static/Load Testing (Up to 10,000lbs) Durability/Door Slam Extreme Temperature Reach-In (Up to 3 x 3 x 3 ) Walk-In (8 x 8 x 8 ) Drive-In (22 x 8 x 8 ) (-40 C to +115 C) Reach-In (4.5 x 3 x 3 ) (-40 C to +150 C) Linear/Inverted Pendulum Impact Testing Impact Velocity Up to 30 mph (Linear) Up to 41 mph (Pendulum) Impact Mass Up to 15 lbs FMVSS 207, 210, 225 (NHTSA) Compliance Cycling of Various Types of Vehicle Components (i.e., Seats, Doors, IPs) GMW 14124; PF-11029, PF-11084; BMW TP303; PR 308; FLTM BN MGATP_SC_IMPACT (In-house method) (A2LA Cert. No ) Revised 04/18/2016 Page 1 of 4

2 Test Description/Parameter Vibration Testing Sine and Random 25mm Displacement Peak to Peak; Up to 3,000 Hz, 4000 lbf sine MIL-STD 810; BMW TP309 Material Testing: Test Name 20, 60 & 85 Gloss Evaluation ASTM D523 Adhesion Adhesive Peels Ash Content ASTM D3359 ASTM D903; GMW 14892; PF (Peel Strength Test) ISO (Method A), ISO 1172 (Method A); ASTM D5630 (Procedure B) Chemical Resistance ASTM D1308; GMW 3402; FLTM BN ; LP-463PB Cold Cracking SAE J323 (Method A) Color Evaluation WSS-M15P Compatibility/Stability Crocking/Colorfastness to Rubbing Dimensional Stability AATCC TM107; GM 9141P, SAE J912, J913 AATCC TM8; SAE J861 ISO 2796; SAE J883 Film Thickness ISO 2808 (Method 6B) Flammability (Horizontal and Vertical) Fogging Gravelometer/Chip Resistance FMVSS 302 (NHTSA) Compliance; GMW 3232; SAE J369; HES C206, HES D6003; TB117 (Section A, Part 1), FAR ; BS 5852; TSM0500G; GB 8410; GS97038; DIN ; DBL ; TL1010 GMW 3235; LP-463DB-12-01; SAE J1756 SAE J400 Immersion Determine Water Absorption ASTM D570, D2842, D3575 (Test L) (A2LA Cert. No ) Revised 04/18/2016 Page 2 of 4

3 Test Name Izod Impact Impact Testing on Notched and Un-notched Specimens Mass Per Unit Area Materials Characteristics (Plastics, Foams, Fabrics) Tension, Compression, Seam Strength, Stitch Strength, Stretch & Set, Tear Strength, Flexural, Friction, Weld Strength ASTM D256, D4812; ISO 179, 180 ASTM D3776; GMW 3182; SAE J860 ASTM D624, (Type T), D790, D1056, D1894, D2261, D3574 (Test B-F), D3575 (Test B, D, G, T), D5034, D5035, D5587; FLTM BN ; GMW 3010, GMW 3326; ISO , ; SAE J386 (5.2.6, 5.2.7), J815, J855; FMVSS 209 (TP-209 A1-A3), FMVSS 213 (TP-213 B2.2); ISO 178 Odor SAE J1351; VDA 270 Resistance to Scratching Scuffing Determination Durometer (Shore A) FLTM BN ; LP-463DD-18-01; PF SAE J365 ASTM D2240 Specific Gravity and Density ASTM D792, D3574 (Test A), D3575 (Test W); ISO 845 Taber Abrasion Rotary Platform ASTM D3884; GMW3208; SAE J948, J1530; ISO Thread Testing (Tensile, Twist, Balance, Dye, Color Transfer, Yardage, Crocking, Heat Aging) Wyzenbeek Abrasion Oscillatory Cylinder Abrasion ASTM D204, D1422, D1423; MS-JZ-3-20, MS-JZ-12-20; GMW ASTM D4157; SAE J1530, SAE J948 Dimensional Testing 1 : Parameter Range CMC 2 (±) Comments Length (1D) 3 Up to 305 mm (Up to 12 in) mm (0.003 in) Caliper Up to 914 mm (Up to 36 in) 2.8 mm (0.11 in) Ruler 1 This laboratory offers commercial dimensional testing service only. (A2LA Cert. No ) Revised 04/18/2016 Page 3 of 4

4 2 Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement that a laboratory can achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards of nearly ideal measuring equipment. CMC s represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory may be greater than the CMC due to the behavior of the customer s device and to influences from the circumstances of the specific calibration. 3 This test is not equivalent to that of a calibration. In addition, customer-supplied test specifications and industry-accepted specifications may be used in conjunction with all of the above procedures. These specifications include: AATCC, ASTM, ISO, MIL-STD, SAE, DIN, JIS Chrysler PF and LP requirements (Materials) GM GMN/GMW/MTL/P/M Ford DVM for IP (Interiors), ST (Seats), MA (Materials) and FLTM (Materials) Other OEM methods from Nissan, Honda, Toyota, Mazda, BMW, VW, Audi, Fiat and Mercedes. (A2LA Cert. No ) Revised 04/18/2016 Page 4 of 4

5 Accredited Laboratory A2LA has accredited MGA RESEARCH CORPORATION Greer, SC for technical competence in the field of Mechanical Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 14 th day of July Senior Director of Quality & Communications For the Accreditation Council Certificate Number Valid to May 31, 2017 Revised April 18, 2016 For the types of tests to which this accreditation applies, please refer to the laboratory s Mechanical Scope of Accreditation.