keep your measure under control
|
|
- Claude Gilbert
- 7 years ago
- Views:
Transcription
1 INSTRUMENTACIÓN INDUSTRIAL ZURC, S.A. keep your measure under control
2 CURRENT For measuring instruments. Mounted in selfexinguishing, plastic, strengthened cases. Isolation voltage V Made as per UNEEN IEC Frequency 0 or 0 Hz General Options For the proper choice of a current transformer following points must be considered: For currents lower than 0 A it is advisable using wound primary models. For bus bar models rossing the wire through the hole a number of times multuple of the C.T. rated current, might be also possible. For instance, to measure A, to 0 A transformers with 0/= cable turns would be appropiate. Dimensions of the primary cable or bus bar. The real use power in at the transformer terminals. To obtain that data, add the drop in the cable (see table) to the consumption of all equipment connected to the secundary line. Table of losses in connection cables () L= Distance from the transformer to the load
3 CURRENT. NARROW SECTION SERIE TC Fixing device for transformers type TC TC., TC and TC. Range primary currents to.000 A Range output burden to 0 Accuracy class: 0., and Secondary current.../a or.../ A Passingbar current transformer. Indoor use. Policarbonate with fiberglass case. Selfextinguishing coating V0. Thermal class B (ºC). TC Type TC Class 0, Class 0, kg TC Type TC Class 0, Class 0, kg TC. Type TC. Class 0, Class TC 0, kg Type TC Class 0, Class 0, kg Type TC. TC. Class 0, Class 0 0,7,7 7, 0,, 0, 0, 0, 7 0, 0, 0, Sealable secondary side terminals. Secondary terminals IP. DIN Rail accessory for TC & TC. Security factor FS. Highest voltage for equipment, 0,7 kv. Isolation voltage, kv. Working frequency, 00 Hz. Short circuit thermal current, Ith=0 In. Dynamic current, Idyn=, Ith. Standard: IEC, BS 7. 0, 7,,7 7, 7 0,,,,7 0,,,,7,7,, 0 0 0,,,,7,7, 0, 0,, 0,7 0 7, 7,, 7, 00 7, 7, 0 7, 0 7, 7, 00 7, 7, , 0 0 7, 7, 0 00
4 CURRENT. NARROW SECTION TC 8 Class 0, Class 0,0 kg 0, 7, 0, 7, 00 7, Type TC 8 V TC 8. 0, kg Class 0, Class Type TC 8. TC 0,80 kg Class 0, Class 0, 0, 7, 00 7,, 7, 7, , Type TC TC 0,8 kg Type TC Class 0, Class CURRENT. NARROW SECTION. HIGH ACCURACY SERIE TCH Special applications, laboratory. Range primary currents 0 to.000 A Range output burden to Accuracy class: 0.S, 0, and 0.S Secondary current.../a or.../ A Passingbar current transformer. Indoor use. Policarbonate with fiberglass case. Selfextinguishing coating V0. Thermal class B (ºC). Sealable secondary side terminals. Secondary terminals IP. DIN Rail accessory for TC & TC. Security factor FS. Highest voltage for equipment, 0,7 kv. Isolation voltage, kv. Working frequency, 00 Hz. Short circuit thermal current, Ith=0 In. Dynamic current, Idyn=, Ith. Standard: IEC, BS 7. Fixing device for transformers type TC TC., TC and TC. 0, kg Type TCH. TCH. Class 0,S Class 0, Class 0,S 0 0, 0,, 0,, 0,,,,, 0, 0 0 7, 7, 7,
5 CURRENT. NARROW SECTION. HIGH ACCURACY SERIE TCH Special applications, laboratory. 0, kg TCH Type TCH Class 0,S Class 0, Class 0,S 0,0 kg TCH 8 Type TCH 8 Class 0,S Class 0, Class 0,S TCH 0,80 kg Type TCH Class 0,S Class 0, Class 0,S 0,8 kg TCH Type TCH Class 0,S Class 0, Class 0,S 0,, 0,, 70 7, 0 00,7 7,, 7, 0,,7, 7, 00 7, , 7, , 7, 70 7, 7, CURRENT. GENERAL APPLICATIONS SERIE TA TA / TA 00 / TA TA Range primary currents to A Range output burden to Accuracy class: 0., and Secondary current.../a or.../ A Indoor use. Policarbonate with selfextinguishing V0. Thermal class A (ºC). Sealable secondary terminals. Security factor, FS. Highest voltage for equipment, 0,7 kv. Isolation voltage, kv. Working frequency, 00 Hz. Short circuit thermal current, Ith=0 In. Dynamic current, Idyn=, Ith. Standard: IEC / UNE EN. Range primary currents: TA / TA 00: 70 to A TA : 00 to 000A Range output burden: TA / TA 00: to 70 TA : to 80 Accuracy class: 0., and Secondary current.../a ó.../ A Indoor use. Policarbonate with selfextinguishing V0. Thermal class A (ºC). Sealable secondary terminals. Security factor, FS. Highest voltage for equipment, 0,7 kv. Isolation voltage, kv. Working frequency, 00 Hz. Short circuit thermal current, Ith=0 In. Dynamic current, Idyn=, Ith. Standard: IEC / UNE EN.
6 CURRENT. GENERAL APPLICATIONS TA Wound Primary SERIE TA 0,80 kg Type TA Class 0, Class For 0x mm bus bar,09 kg Type TA Class 0, Class Class 0, Class For 0x mm bus bar TA Sealable terminal cover and fixing base included 0,8 kg TA 00 Type 00 0 Sealable terminal cover and fixing base included TA 0,7 kg Type TA 0 Class 0, Class Sealable terminal cover and fixing base included CURRENT. DIN RAIL MOUNTING SERIE TM / TW Indoor use. ABS with selfextinguishing. Thermal class A (ºC). Fixing by rail DIN 77, EN 00. Security factor, FS. Isolation voltage, kv. Working frequency, 00 Hz. Short circuit thermal current, Ith=0 In. Dynamic current, Idyn=, Ith. Standard: IEC / UNE EN. Wound primary current transformer Range primary current to 0A Range output burden:, to 7 Accuracy class 0., and Secondary current or A TM Wound Primary Fixing system: to fit onto symmetrical DIN 77 (EN 0 0) 0,8 kg Type TM Class 0, Class, 7 0 Fixing system: to fit onto symmetrical DIN 77 (EN 0 0) TW Cable Passing bar current transformer. Range primary current 0 to 0A Range output burden:, to Accuracy class 0., and Secondary current or A Class 0, Class 0, , kg Type TW
7 CURRENT ADDING TRANSFORMER SERIE TSR Class 0, TSR additions (+ / A) TSR additions (++ / A) TSR additions (+++ / A) TSR additions (++++ / A) 0,80 kg Type TSR Number of input circuits:,, or. Output power:. Thermal class A (ºC). Input circuit current, ln / A. Output circuit current, A. Short circuit thermal current, lth=0 ln. Fixing by rail DIN 77, EN 00. Standard: IEC, UNE 088, UL9, VDE 0. SPLIT CORE CURRENT. SERIE TP CLIP The TPClip have been designed to facilitate their installation in new or already existing networks. Thanks to ist split core they may be installed without opening any cable or bus bar circuit. New The connection of the conventional Cts usually requires the interruption of the primary side circuit to pass cables bus bar through the transformer core or to connect such cables to primary terminals. The TPClip may be easily opened and they may be installed and connected without any supply interruption, thus saving time and installation costs. Selfextinguishable UNE V0 Thermal class B(º) Storage temperature C to 8 C Relative Humidity % to 8% (without condensing) Frequency Range 0Hz 0Hz Rated output... Rated insulation level kv Sorttime thermal current (Ith)0 In Rated dynamic current, Ith Highest voltage for equipment 0,7 kv a.c. Rated current I(A) / 0/ 0/ 0/ 0/ I(A) 0/ 0/ 0/ 0/. SERIE TP Características técnicas Indoor use. Policarbonate with selfextinguishing V0. Sealable secondary terminals. Highest voltage for equipment, 0,7 kv. Range output burden: 0A to 0A Secondary current.../a or.../ A 0,7 kg 0,90 kg,00 kg, kg,0 kg 0, Class 0, Class TP 8 TP TP8 TP88 TP8 TP8 TP Class 0, Class 0 7, 0 0 Isolation voltage, kv. Working frequency, 00 Hz. Short circuit thermal current, Ith= In. Dynamic current, Idyn=, Ith. High accuracy and reliability 0, 0 0,, ,,,, 7, 0 700, 7, 0, , 000 7
8 SPLIT CORE CURRENT. SERIE TP TP 88 TP 8 00 Class 0, Class TP 8 0 Class 0, Class Class 0, Class 0, 70 7, 00,, 7, CURRENT WITH BUILTIN CONVERTER SERIE TC TC 0, kg SERIE TC 0 TC 0, kg TC0 0, kg TC8 0,0 kg Output:... ma Supply Voltage: 7,... V c.c. Frequency: a Hz (Output external supply... ma) CONNECTION DIAGRAM RESISTANCE OF LOAD: TC80 0,0 kg Selfsupply Output: 0... ma Frequency: a Hz Resistance of load: 0 to 0 U A RMÁX = 0,0 Wiring diagram and maximum load... ma 7,... V 00 R 00 R < 0 0 ma 0 R carga TC Ø Bar x mm 7, TC Ø 8 Bar x mm V TC8 Ø Bar 0x mm (A) TC80 TC0 Ø 8 Bar Ø Bar x mm 0x mm (A)
9 CURRENT WITH BUILTIN CONVERTER SERIE TP (Split core) External supply Output:... ma Supply Voltage:...8 V c.c. Frequency: to Hz TP TP TP TP TP x 0x80 80x80 80x 80x0 Sealable connection terminal box Metallic holders for fixing Selfextinguishing UL9VO TP Bar (mm x mm) x 0x80 80x80 80x 80x0 (A) ,7 kg 0,90 kg,00 kg, kg,0 kg Type TP SERIE TCM TCB Serie with supply of C (Internal supply) Type TCM for fixing at panel bottom or onto DIN 77 Closed core type TCB Output ma Frequency to Hz Sealable connection terminal box Metallic holders for fixing Selfextinguishing UL9VO Máxima Carga: 0 TCM ( ) 0 TCM ( ) 0 TCB 0, kg Type TCM TCM TCM Ø Ø (A), TCB TCB Ø TCB Ø 0,9 kg TCB Ø 70 0, kg TCB Ø 0,8 kg TCB Ø 70 Ø (A), Type TCB CURRENT FOR ENERGY METERS SERIE TRMC Technical Specification Enclosure of selfextinguishing V0, synthetic resin (TRMC). Policarbonate with selfextinguishing V0 (TRMC). Thermal class B (ºC). Sealable secondary side terminals. Security factor, FS. Highest voltage for equipment, 0,7 kv. Isolation voltage, kv. Working frequency, 00 Hz. Short circuit thermal current, lth=0 ln. Dynamic current, ldyn=, lth. Standard: IEC / UNE EN. 9
10 , kg Transformador de primario bobinado Rango de intensidades de corriente de primario 0 a A Rango de potencias a Classs de precisión 0.S y 0. Intensidades de secundario ó A TRMC 0 0 Class 0, Class 0,S Wound Primary CURRENT FOR ENERGY METERS , kg Transformador Type Bar pasante Rango de intensidades de corriente de primario 70 a 00 A Rango de potencias a Classs de precisión 0.S y 0. Intensidades de secundario ó A Type TRMC TRMC Bar 0x Type TRMC Class 0, Class 0,S PROTECTION CURRENT. Range primary currents: 0 to 000A Range output burden, to Accuracy class: P and P Secondary current.../a or.../a Passingbar current transformer. Indoor use. Enclosure of selfextinguishing V0, synthetic resin. Thermal class B (ºC). Sealable secondary side terminals. Highest voltage for equipment, 0,7 kv. Isolation voltage, kv. Working frequency, 00 Hz. Short circuit thermal current, lth=0 ln. Dynamic current, ldyn=, lth. Standard: IEC / UNE EN. 9, kg TRP Type TRP ,9 kg TRP 0 Type TRP0 0, 0, , , kg TRP , Type TRP80, kg TRP , Type TRP0
11 PROTECTION CURRENT. 7, kg TRP Type TRP 8,9 kg TRP , Type TRP80 MEASUREMENT RESIN CASE CURRENT Características técnicas Range primary currents: 0 to 000A Range output burden, to Accuracy class: 0, and Secondary current.../a or.../a Passingbar current transformer. Indoor use. Enclosure of selfextinguishing V0, synthetic resin. Thermal class B (ºC). Sealable secondary side terminals. Highest voltage for equipment, 0,7 kv. Isolation voltage, kv. Working frequency, 00 Hz. Short circuit thermal current, lth=0 ln. Dynamic current, ldyn=, lth. Standard: IEC / UNE EN., kg TRM Type TRM Class 0,, kg 0 0 TRM Type TRM 0 0 Class 0,, 0 0 7, , kg TRM 0 Class 0, 0 0 7, Type TRM0, kg TRM 80 Class 0, , Type TRM80
12 MEASUREMENT RESIN CASE CURRENT, kg TRM Type TRM Class 0, ,7 kg TRM 0 Class 0, Type TRM0, kg TRM Class 0, Type TRM, kg TRM 80 Class 0, Type TRM80 ** FOR SPECIAL NOT LISTED, PLEASE CONSULT ** Instrumentación Industrial ZURC, SA C/Innovació, P.l. Can Mitjans, 08 Viladecavalls (Barcelona) SPAIN Tel. (+) Fax (+) central@zurc.com web:
Current transformers (CT) & Shunts
Current transformers (CT) & Shunts Genreal overview LV CURRENT TRANSFORMERS Product selection guide Standard industrial transformers?????? TCR - TCRO range NEW 9 9 9 Current summation JVM 0 9 TCR usbar
More informationTape Wound, Split Core and Ebony Current Transformers
Tape Wound, Split Core and Ebony Current Transformers Current Transformers Contents Page Tape Wound Measuring and Protection Current Transformers 2 6 Split Core Current Transformers 7 9 3-in-1 Current
More informationTape Wound, Split Core and Ebony Current Transformers
Tape Wound, Split Core and Ebony Current Transformers Table of contents Tape Wound Measuring and Protection Current Transformers 2 MR Series Measuring Range 3 PR Series Protection Range 4 Class PX Current
More informationRM17TE 183...528 V AC. Main. Product or component type. Product specific application. Relay monitored parameters 250 V DC 5 A DC
Characteristics multifunction control relay RM17-TE - range 183..528 V AC Complementary Reset time Maximum switching voltage Minimum switching current Maximum switching current [Us] rated supply voltage
More informationVario-Series Accessories
Accessories and spare parts for GMW analogue panel meters and controllers Current Transformers pages 2-9 Shunt Resistors 10-11 Voltage Dividers 12 Power supply for indicator/controllers 13 Blanking Plates
More informationRM4TG20 three-phase network control relay RM4-T - range 200..500 V
Characteristics three-phase network control relay RM4-T - range 200..500 V Complementary [Us] rated supply voltage Output contacts Setting accuracy of time delay Delay at power up Measuring cycle Marking
More informationLOW-VOLTAGE CURRENT TRANSFORMERS
LOWVOLTAGE CURRENT TRANSFORMERS 5 A Power network meters ND0 and ND type. N4Z and N5Z Tel: (+48 68) 45 75 39; 45 75 305; 45 75 3; 45 75 368; email: export@lumel.com.pl ul. Słubicka 657 Zielona Góra CONTENTS
More informationEnhanced Quality with a Touch of Style
Rudolf Current Transformer Enhanced Quality with a Touch of Style Current Transformer Enhanced Quality with a Touch of Style New Products Rudolf launched our new encapsulated current transformer. Portraying
More informationRM35UA13MW. range 15..600 V. Main. Product or component type. Relay monitored parameters
Characteristics multifunction voltage control relay RM35-U - range 15..600 V Complementary Reset time Maximum switching voltage [Us] rated supply voltage Supply voltage limits Power consumption in W Main
More informationMeasurement and Instrumentation
POWER QUALITY ENERGY PERFORMANCE Measurement and Instrumentation Transformers and shunts Transformers Overview of ranges Selection guide Info & advice Standard industrial transformers TCR TCRO ranges Adaptable
More informationMeasurement devices Accessories for analogue and digital instruments
Accessories for analogue and digital instruments 1 2CSC96F0001 Current transformers Used to transform primary currents (max. 6000 A) into.../5 A and.../1 A low secondary currents indirectly supplying power
More informationCurrent valve. for AC 24 V pulse/pause control of electrical loads up to 30 kw
4 937 DESIO Current valve for AC 24 V pulse/pause control of electrical loads up to 30 kw SEA45.1 Use The current valve is used for the control of electric heating elements in heating, ventilation and
More informationMedium-voltage transformers
Medium-voltage transformers We make energy measurable and take care of your future www.mbs-ag.com Page 2 E-Mail: info@mbs-ag.com Web: www.mbs-ag.com Contents Current transformers Technical characteristics
More informationH/L = Power supply. FN = Nominal Frequency. RN = Rated value of output burden. UN = Nominal input voltage. IN = Nominal input current.
Application : The transducer RISH CON - CA/CV (Fig.1) converts a sinusoidal AC Current or AC Voltage into a load independent DC Current or a load independent DC Voltage proportional to the measured value.
More informationZ-TRAUQ INC. Tel.: (450)226-6997 Fax: (450)226-5837 z-trauq@qc.aira.com
CURRENT TRANSFORMER MODEL J " x 7" PAGE No 2-2 REV 8DEC00 TERMINAL OPTION LEAD WIRE OPTION 8-2 BRASS SCREW TERMINALS (2 PLACES) SEE NOTE 9 6 9 8 6 Ø 2 9 (4 PLACES) UL 05 #6 AWG LEAD WIRE, STANDARD LENGTH
More informationKOLMA and IHDA Indoor type Cable Current Transformers Catalogue ABB Power Distribution ABB Transmit 1 KKOLMA 1 GB
KOLMA and IHDA Indoor type Cable Current Transformers Catalogue ABB Power Distribution ABB Transmit 1 KKOLMA 1 GB KOLMA and IHDA Indoor Type Cable Current Transformers Index Description... 3 Technical
More informationElectronic timer CT-VBS.17+18 OFF-delayed without auxiliary voltage, for DC contactors Data sheet
Characteristics Single-function OFF-delay timer for DC contactors, without auxiliary voltage Width.5 mm CDC 5 6 F3 Approvals A culus E CCC CT-VBS a Circuit diagram b Marker label Marks a CE b C-Tick Order
More informationQuick Connect. quick - simple - efficient. www.g-mw.de
Quick Connect quick - simple - efficient www.g-mw.de Phone: +49 9103 7129-0 Fax: +49 9103 7129-207 Innovative connection technology to plug three single-phase current transformers to multifunctional power
More informationPCB transformers. Short circuit proof PCB transformer VB. General Data. Advantages. Applications. Circuit diagram. Standards & 1 Certifications W v
Short circuit PCB transformer General Data Rated input 230 Vac Rated output 6-2 x 24 Vac Rated power 0.35-3.2 VA Insulation class B Maximum ambient temperature 70 C Efficiency up to 58 % Degree of protection
More informationM.7 CONTENTS. Measurement transformers and shunts. Introduction Page 3 TC 5 TC 5,2 TC 6,2 TC 6 TC 8 TC 10 TC 12. Slim line current transformers Page 7
Current transformers and shunts M7 M.7.01 GB CONTENTS Introdution Page 3 TC TCH T TC 5 TC 5,2 TC 6,2 TC 6 TC 8 TC 10 TC 12 TCH 6,2 TCH 6 TCH 8 TCH 10 TCH 12 T 400 T 0 T 600 Slim line urrent transformers
More informationActuator-Sensor-Interface
Selection and ordering data Design Order No. Price Pack 3RX9 307-0AA00 3RX9 307-1AA00 4FD5 213-0AA10-1A 3RX9 305-1AA00 3RX9 306-1AA00 Single output IP 65 current 2.4 A Rated input voltage DC 24 V current
More informationSafety automation solutions
Operating principle, characteristics Preventa safety s types XPS AV,, For and switch monitoring Operating principle Safety s XPS AV, and are used for monitoring circuits conforming to standards EN/ISO
More informationCURRENT TRANSFORMER MODEL 546 UL1015 #16 AWG LEAD WIRE, STANDARD LENGTH IS 24" 1 X
CURRENT TRANSFORMER MODEL 546 1.10" I.D. PAGE No 1-38 REV 15DEC00 TERMINAL OPTION LEAD WIRE OPTION 1.10 0 1.20 2.55 3.00 3.47 0.18 x 0.31 SLOT ( 2 PLACES) 8-32 BRASS STUD (2 PLACES) UL1015 #16 AWG LEAD
More informationElectronic overload relay EF19 and EF45
Data sheet Electronic overload relay EF19 and EF45 Electronic overload relays offer reliable protection in case of overload and phase-failure. They are the alternative to thermal overload relays. Motor
More informationMaximum Demand Control
Maximum Demand Control There are three terms that appear on the majority of electric company bills: Active energy consumption (kwh) Reactive energy consumption (kvarh) Maximum Demand Traditionally, utility
More informationSINEAX U553 Transducer for AC Voltage
With power supply RMS value measurement Carrying rail housing P/0 Application he transducer SINEAX U55 (Fig. ) converts a sinusoidal or a distorted AC voltage into a load independent DC current or a load
More informationRISH CON - Hz. Salient Features : Application : Product Features: FREQUENCY TRANSDUCER
Application : The RISH CON - Hz transducer is used for frequency measurement. The output signal is proportional to measured frequency and is either load independent DC Current or load independent DC Voltage.
More informationFeatures. Display. Measurements. Intelligent. Accuracy. Models. Installation DEIF A/S. Multi-instrument 4921210109D
7000/7000C/7020 Multi-instrument 4921210109D Features Measurements All 3-phase AC measurements True RMS Replaces analogue meters Demand on each phase current Accuracy U, I and F class 0.5 Other values
More informationDifferential Pressure Sensors for air and non-corrosive gases, with calibration certificate
1 919 1919P01 1919P03 QBM65/C, QBM75-1U/C Differential Pressure Sensors for air and non-corrosive gases, with calibration certificate QBM751-1/C QBM65/C QBM75/C Highly accurate measurements with calibration
More informationA project to optimise quality and energy efficiency must include metering
EMDX 3 : Energy Metering A project to optimise quality and energy efficiency must include metering Metering upstream identifies the critical points and ensures optimum targeting of the actions to be taken,
More informationPower Supply Unit, Primary Switched, Narrow Design MINI-PS-12-24DC/24DC/1
Power Supply Unit, Primary Switched, Narrow Design MINI POWER provides: Extra narrow design with widths of 22.5 mm, 45 mm, and 67.5 mm (0.886, 1.772, and 2.657 in.) Global use due to a wide-range input
More informationVoltage Regulator SPAU 341 C. Product Guide
Issued: July 1998 Status: Updated Version: D/25.04.2006 Data subject to change without notice Features Comprehensive voltage regulation for power transformers with on-load tapchangers in distribution substations
More information3-phase, bidirectional energy meter
Data sheet www.sbc-support.com 3-phase, bidirectional energy meter with S0 pulse output Bidirectional energy meter with S0-interface. The S0 interface is a hardware interface for the transmission of measured
More informationElectronic timer CT-AHD.12 OFF-delayed with 1 c/o (SPDT) contact
Data sheet Electronic timer CT-AHD.12 OFF-delayed with 1 c/o (SPDT) contact The CT-AHD.12 is an electronic time relay with OFF-delay. It is from the CT-D range. With their MDRC profile and a width of only
More information3.1.1 Full Type Tests & Routine Tests according to Clause 8 2 & 8 3. 4.0 Instructions For Installation, Operation & Maintenance
SPECIFICATION FOR LOW VOLTAGE SWITCHBOARD SEN I N D E X Description 10 STANDARD TECHNICAL REQUIREMENTS 11 Standards 12 General Operating Conditions 13 General Description Of Switchboard 131 Structure 132
More informationHSP GmbH Zum Handwerkerhof 2 90530 Wendelstein Tel. 09129 / 2852-0 Fax: 09129 / 2852-11 Web: www.hsshsp.de EMAIL: HSP@hsshsp.de NTG-3000.
NTG-3000 Transducer Data Sheet Document Version 2.8 Page 1 of 10 Versions / Revisions: Document Creation Author Description version date 2.0 2012-07-25 P. Compensis First official version 2.1 2012-08-24
More informationPD30ETB20xxIS. Photoelectrics, Background Suppression reflective with IR light. Main features. Description
Photoelectrics, Background Suppression reflective with IR light Main features Description The PD30ET... stainless steel sensors are built with high-quality materials and designed for harsh environments.
More informationElectronic ballasts for fluorescent lamps Products for special applications. PC BASIC, 4 28 W Electronic ballast for system output < 25 W
T5 TC-DEL TC-SEL TC-TEL TC-DD PC BASIC, 4 28 W Electronic ballast for system output < 25 W Product description CELMA Energy Efficiency Index A2 / A3 Nominal life time up to 50,000 h (at ta 50 C with a
More informationMedium voltage product. Instrument transformers for indoor applications Product overview
Medium voltage product Instrument transformers for indoor applications Product overview 02 Contents Introduction Current transformers Supporting type 6 TPU, TPE 7 KOFA, IHBF 10 Dummy Bus type 8 KOKS 12,
More informationType: EASY719 DC RC Article No.: 274119. Ordering information Relay outputs Quantity 6 Power supply V DC 24 V DC. Description
Type: EASY719 DC RC Article.: 274119 Ordering information Relay outputs Quantity 6 Power supply V DC 24 V DC Description 12 digital inputs (4 inputs available as analog inputs) 6 relay outputs LCD display
More informationMeter Relays. 077 Series Analogue Meter Relays. Features. Applications
077 Series Analogue Features Monitors and controls any variable which can be converted to an A.C. or D.C. signal. Rugged, shock and vibration resistant design Indicator, relays and power unit in one housing
More informationTLK 48 MICROPROCESSOR-BASED DIGITAL ELECTRONIC REGULATOR
TLK 48 MICROPROCESSOR-BASED DIGITAL ELECTRONIC REGULATOR TECHNICAL DATA CARATTERISTICHE MECCANICHE Housing Self-extinguishing plastic, UL 94 V0 Dimensions 48x48 mm DIN depth 98 mm Weight 225 g approx.
More informationDRM75A 230V 20/100A DIN rail single phase two wire energy meter
DRM75A 230V 20/100A DIN rail single phase two wire energy meter 1.1 Safety instruction 1.2 Foreword 1.3 Performance criteria 1.4 Specifications 1.5 Basic errors 1.6 Description 1.7 Dimensions 1.8 Installation
More informationMONITORING RELAYS. w VOLTAGE MONITORING RELAY UR5U1011. w SCHRACK-INFO. w TECHNICAL DATA
w VOLTAGE MONITORING RELAY UR5U1011 w SCHRACK-INFO AC/DC voltage monitoring in 1-phase mains Undervoltage monitoring 1 change over contact Width 17.5 mm Installation design w TECHNICAL DATA 502 1. Functions
More informationVoltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages
Data sheet Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages The CM-ESS.2 is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of
More informationElectronic overload relay EF65, EF96 and EF146
Data sheet Electronic overload relay EF65, EF96 and EF146 Electronic overload relays offer reliable protection in case of overload and phase-failure. They are the alternative to thermal overload relays.
More informationHow To Read A Pipe From A Sensor
Liquid Level Sensor Installation on pipes. Sensing by means electrostatic capacity and is not influenced by the color of the pipe or liquid. Available in 8 to mm dia. and to mm dia. models to enable sensing
More informationHow To Build A Low Voltage Capacitor Lvcp
Low Voltage Capacitor LVCP The new choice for Power Factor Correction LVCP : the new choice for Power Factor Correction The LVCP is a compact and powerful capacitor. It offers high modularity, unmatched
More informationUser Manual V1.0 2014 SDM220MODBUS. Single-Phase Two Module DIN rail Meters
SDM220MODBUS Single-Phase Two Module DIN rail Meters Measures kwh, Kvarh, KW, Kvar, KVA, PF, Hz, dmd, V, A, etc. Di-directional measurement IMP & EXP Two pulse outputs RS485 Modbus Din rail mounting 36mm
More informationSURGE PROTECTIVE DEVICES
SURGE PROTECTIVE DEVICES 1. INTRODUCTION In order to ensure safety of people, protection of equipment and, to a certain extent, continuity of supply, insulation co-ordination aims at reducing the likelihood
More informationHERZ-Thermal Actuators
HERZ-Thermal Actuators Data Sheet 7708-7990, Issue 1011 Dimensions in mm 1 7710 00 1 7710 01 1 7711 18 1 7710 80 1 7710 81 1 7711 80 1 7711 81 1 7990 00 1 7980 00 1 7708 11 1 7708 10 1 7708 23 1 7709 01
More informationAnalog signal converters CC-E I/I Current / current isolators
ata sheet Analog signal converters CC-E I/I Current / current isolators The CC-E I/I is an isolator for the electrical isolation of current signals without auxiliary supply. It allows the isolation between
More informationVEO. V4PF480Y/277VSYTK02 Art.Nr.: 2104200. V4PF480Y/277VSYTK02P Art.Nr.: 2104210 TECHNICAL DATA
Monitoring of phase sequence and phase loss Monitoring of asymmetry Temperature monitoring (PTC) Supply voltage 208-480 V AC Supply circuit = measuring circuit 2 change-over contacts Width 45 mm Control
More informationPositive-guided relay outputs: 3 safety contacts (N/O), instantaneous. 1 auxiliary contact (N/C), instantaneous
Safety relay for monitoring E-STOP pushbuttons. Approvals Unit features Positive-guided relay outputs: 3 safety contacts (N/O), instantaneous 1 auxiliary contact (N/C), instantaneous Safe separation of
More informationYour Advantages For safety application up to PL e / Cat. 4 e.g. SIL 3 Manual or automatic start 0225592. * see variants. Applications.
Safety Technique SAFEMASTER Emergency Stop Module BG 5924, IP 5924 Your Advantages For safety application up to PL e / Cat. 4 e.g. SIL 3 Manual or automatic start 0225592 BG 5924 IP 5924 Product Description
More informationThermal-Magnetic Circuit Breaker 3120-...-M1-..
Thermal-Magnetic Circuit Breaker -...-M-.. Description Single or two pole rocker switch/thermal-magnetic circuit breaker with trip-free mechanism (S-type TM CBE to EN 34). The addition of a magnetic tripping
More informationElectrical and mechanical interface requirements for separable HR, LR and LRM voltage detecting systems
C Metal-encapsulated switchgear installations, typically SF6 gas-insulated, have become widely accepted in the field of switchgear construction. In these types of installation, conventional voltage detectors
More informationProduct and Applications Description. Application Programs. Example of Operation. GAMMA instabus Technical Product-Information.
Product and Applications Description The power supply units N 125/x2 can supply DC 24 V power from an additional pair of terminals (yellowwhite). This DC 24 V output voltage can be used to power e.g. an
More informationE-STOP relays, safety gate monitors
Unit features Safety features Gertebild ][Bildunterschrift_NOT_Sch.tuer_Licht Safety relay for monitoring E-STOP pushbuttons, safety gates and light beam devices Approvals Gertemerkmale Positive-guided
More information(68.52) X. June 2000 Supercedes February 2000. xenex CONVENTIONAL FIRE DETECTION & ALARM SYSTEM. we look @ business differently
(68.52) X June 2000 Supercedes February 2000 xenex CONVENTIONAL FIRE DETECTION & ALARM SYSTEM.... we look @ business differently XENEX SYSTEM ARCHITECTURE Note: This schematic is for guidance only please
More informationCompactLogix Power Supplies Specifications
Technical Data CompactLogix Power Supplies Specifications 1768 CompactLogix Power Supplies Catalog Numbers 1768-PA3, 1768-PB3 1769 Compact I/O Power Supplies Catalog Numbers 1769-PA2, 1769-PB2, 1769-PA4,
More informationCONTROLS DATA MANAGEMENT PROCESS AUTOMATION EUROCUBE. General purpose single phase thyristors and solid state relays Product data.
425 CONTROLS DATA MANAGEMENT PROCESS AUTOMATION EUROCUBE General purpose single phase thyristors and solid state relays Product data abc 425 EUROCUBE A complete range of low cost solid state relays and
More informationABB 1. Three-phase monitoring relay CM-PFS. Data sheet. Features. Approvals. Marks. Order data. Order data - Accessories. Application.
1SR 430 824 F9300 Features Monitoring of three-phase mains for phase sequence and failure Powered by the measuring circuit 2 c/o (SPDT) contacts 1 LED for status indication Approvals R: yellow LED - relay
More informationJ TB/TW Temperature limiter, temperature monitor
JUMO GmbH & Co. KG Delivery address:mackenrodtstraße 14, 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 e-mail: mail@jumo.net Internet: www.jumo.net
More informationPower Supply and Indicator Unit Type 5024-1. Fig. 1 Type 5024-1. Mounting and Operating Instructions EB 9539 EN
Power Supply and Indicator Unit Type 5024-1 Fig. 1 Type 5024-1 Mounting and Operating Instructions EB 9539 EN Edition October 2003 Application 1 Application The Type 5024-1 Power Supply and Indicator Unit
More informationDifferential Charge Amplifier
Electronics Differential Type 58A... The differential charge amplifier is used for signal conversion of piezoelectric sensors with differential output. Executions Aluminum die-cast enclosure (IP64) Plastic
More informationDS 600. A contact free flux gate based current measurement sensor 600A rms
DS 600 A contact free flux gate based current measurement sensor 600A rms DS 600 is member of the small housing sensor family. The family includes a 200A and a 600A version. 600A rms - 900A peak Maximum
More informationControl Devices Catalogue. Control Devices. Preferred and Standard Products
Control Devices Catalogue Control Devices Preferred and Standard Products KOP.J Timer Electronic 22.5 mm Characteristics Mounting KOP.J 22.5 mm mono or multifunction high immunity to interference surface
More informationT 3000. Substation Maintenance and Commissioning Test Equipment
T 3000 Substation Maintenance and Commissioning Test Equipment Multi function system for testing substation equipment such as: current, voltage and power transformers, all type of protection relays, energy
More informationDC Electronic Loads 8500 series
Data Sheet DC Electronic Loads 8500 series 2400W 600 W - 1200 W 300 W Versatile & Economical DC Electronic Loads The 8500 series Programmable DC Electronic Loads can be used for testing and evaluating
More informationTemp-485-Pt100. A temperature sensor (Pt100 or Pt1000) communicating over the RS-485 bus with a simple communication protocol
Temp-485-Pt100 A temperature sensor (Pt100 or Pt1000) communicating over the RS-485 bus with a simple communication protocol Temp-485-Pt100 Box version [600 113] Temp-485-Pt100 Cable version [600 114]
More informationSTEP-PS/1AC/12DC/1.5. Extract from the online catalog. Order No.: 2868567. DIN rail power supply unit 12 V DC/1.5 A, primary switched-mode, 1- phase
Extract from the online catalog STEP-PS/1AC/12DC/1.5 Order No.: 2868567 DIN rail power supply unit 12 V DC/1.5 A, primary switched-mode, 1- phase Commercial data EAN 4046356292924 Pack 1 pcs. Customs tariff
More informationEnergy Management Energy Meter Type EM23 DIN
Energy Management Energy Meter Type EM23 DIN Class 1 (kwh) according to EN62053-21 Class B (kwh) according to EN50470-3 Class 2 (kvarh) according to EN62053-23 Accuracy ±0.5 RDG (current/voltage) Energy
More informationABB 1 NEW. Three-phase monitoring relay for grid feeding CM-UFS.1. Data sheet. Features. Approvals. Marks. Order data. Order data - Accessories
2CDC 251 014 F0t09 Features Monitoring of three-phase mains for grid feeding Type-tested in accordance with DIN V VDE V 0126-1-1: February 2006 Neutral conductor connection configurable Can also be used
More informationManual Motor Starter MS 116 up to 16 A Technical Data
Manual Motor Starter MS 116 up to 16 A Technical Data Type MS 116 Standards: Major International IEC 60 947-4-1 / IEC 60 947-2 and European Standards EN 60 947-4-1 / EN 60 947-2 Approvals, Certificates
More informationThyristor-controlled power supplies and battery chargers
Thyristor-controlled power supplies and battery chargers Input voltage: 115 / 230 VAC, single phase, 50 / 60 Hz or 208 / 400 / 480 VAC, three phases, 50 / 60 Hz Output voltage: 12 / 24 / 48 / 60 / 72 /
More informationFilm Capacitors AC Capacitors
Series/Type: Ordering code: Date: Nov 2012 Version: 9 Super MotorCap, 450 V Content of header bars 1 and 2 of data sheet will be automatically entered in headers and footers! Please fill in the table and
More informationRedundancy Module QUINT-DIODE/40
Redundancy Module QUT DIODE provides: 00% decoupling of power supplies connected in parallel Can be installed in potentially explosive areas Load currents up to 60 A supported Easy assembly by snapping
More information3-Phase Energy meter with serial S-Bus interface
Data sheet www.sbc-support.com 3-Phase Energy meter with serial S-Bus interface Energy meters with an integrated S-Bus interface allow direct reading of all relevant data, such as energy (Total and partial),
More informationRISH EM 3490 DS Dual Source Energy Meter RISH EM 3490 DS. Application : Product Features:
Application : RISH Master 3490 DS measures important electrical parameters of Utility (in normal mode) & Generators (in Power back up) in three phase and single phase Network & replaces the multiple analog
More informationVoltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages
Data sheet Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages The CM-ESS.2 is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of
More information0.84" x 2.00" Z-TRAUQ INC. Tel.: (450)226-6997 Fax: (450)226-5837 z-trauq@qc.aira.com SPLIT CORE CURRENT TRANSFORMER MODEL 1SP.
SPLIT CORE CURRENT MODEL 1SP 0.84" x 2.00" PAGE No 3-2 REV 18DEC00 UL 1015 LEAD WIRE, STANDARD LENGTH IS 36 E DIMENSIONS A = 0.84 MIN B = 2.00 MIN C = 3.31 MAX D = 3.09 MAX E = 0.61 MAX F = 0 MAX F C B
More informationLINETRAXX VMD460-NA. Network and system protection (NS protection) for monitoring the power feed-in of power generation systems
LIETRAXX -A etwork and system protection (S protection) for monitoring the power feed-in of power generation systems TDB301021en/06.2013 LIETRAXX -A etwork and system protection (S protection) for monitoring
More informationR.C.C.B. s two-pole LEXIC
87045 LIMOGES Cedex Telephone : (+33) 05 55 06 87 87 Fax : (+ 33) 05 55 06 88 88 R.C.C.B. s two-pole LEXIC 089 06/09/10/11/12/15/16/17/18/ 27/28/29/30/35, CONTENTS PAGES 1. Electrical and mechanical characteristics...
More informationManual motor starter MS116
Data sheet Manual motor starter MS116 Manual motor starters are electromechanical devices for motor and circuit protection. These devices offer local motor disconnect means, manual ON/ OFF control, and
More informationAUTOMATIC TRANSFER SWITCH. Changeover Type from 250A to 2500A
AUTOMATIC TRANSFER SWITCH Changeover Type from 250A to 2500A Table of Contents Preamble 1.1 Theoretical base 1.2 Selection the size of automatic transfer switch 1.3 Automatic transfer switch components
More informationTechnical data UNIBLOCK UBSF 180 625
Data TECHNICL DT Technical data UNIBLOCK UBSF 80 6 Output data Type UBSF 80 UBSF 0 UBSF 00 UBSF 6 Output power 80 kv 0 kv 00 kv 6 kv Output voltage 80/77 V 0/ V 0/ V 0/ V Output current 7 8 66 80 Power
More informationMagnetic and Hydraulic-Magnetic Circuit Breaker 8340-G2...
Magnetic and Hydraulic-Magnetic Circuit Breaker 840-G2... Description Single, two and three pole magnetic circuit breakers with trip-free mechanism and push/pull on/off manual actuation. A choice of fast
More informationSeries 8146/5-V37 and Series 8150/5-V37
www.stahl.de > Clear assignment safe technology easy installation > Intelligent structure only one rotary actuator for frequency-controlled drives ) 20 ms leading auxiliary contact for safe motor disconnection
More informationThermistor motor protection relays CM-MSS.22 and CM-MSS.23
Data sheet Thermistor motor protection relays CM-MSS.22 and CM-MSS.23 The thermistor motor protection relays CM-MSS.22 and CM-MSS.23 monitor the winding temperature of motors and protect them from overheating,
More informationCross-beam scanning system to detect slim objects. 100 mm 3.937 in
891 Object Area Sensor General terms and conditions... F-17 Related Information Glossary of terms... P.1359~ Sensor selection guide...p.831~ General precautions... P.1405 PHOTO PHOTO Conforming to EMC
More informationMLC 9000+ TM Maximum Productivity and Versatility for Control without Compromise!
Data Sheet Maximum Productivity and Versatility for Control without Compromise! Basic Bus Communication Module DESCRIPTION The Basic Bus Communication Module (BCM) is part of the MLC 9000+ DIN rail mount
More informationMILLENIUM INSTALLATION MANUAL NTR 735 A. Simple Automation Control Module (MAS)
MILLENIUM Table of contents 1. INTRODUCTION 1 2. HARDWARE DESCRIPTION 2 3. INSTALLATION 5 4. CONNECTION 6 5. USER SAFETY AND PROTECTION OF EQUIPMENT 8 1. Introduction The MILLENIUM series has been designed
More informationSEZ220. Signal Converter. Synco 200. With preprogrammed standard applications Freely programmable Menu-driven operation. Use
s 5 146 Synco 200 Signal Converter SEZ220 With preprogrammed standard applications Freely programmable enu-driven operation Use The signal converter is for use in HVAC plant to provide minimum / maximum
More informationTemperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection)
Data sheet Temperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection) The temperature monitoring relays CM-TCS monitor overtemperature,
More informationLC1D65AM7 TeSys D contactor - 3P(3 NO) - AC-3 - <= 440 V 65 A - 220 V AC coil
Product data sheet Characteristics LC1D65AM7 TeSys D contactor - 3P(3 NO) - AC-3 -
More informationDirectory chapter 02 - DIN Power (to 6 A) Types D, E, F, FM, 2F, F9, interface connectors I/U 02. 01. Technical characteristics types D and E... 02.
Directory chapter 02 - () Types D, E, F, FM, 2F, F9, interface connectors I/U Page Technical characteristics types D and E.............................. 02.10 Type D connectors.................... 02.11
More information40.3. Control Relays and Timers
.3 Contents EASY500/700/800 Intelligent Relays........ EASY/MFD Expansion Modules............ MFD Intelligent Relays................... EASY/MFD Communication Modules....... EASY/MFD Power Supplies, Accessories
More informationTemperature sensor with integrated transmitter for industrial applications, MBT 3560
Temperature sensor with integrated transmitter for industrial applications, MBT 3560 Technical brochure Features Designed for use in harsh industrial enviroments where reliable, robust and accurate equipment
More informationInstallation and operating instructions
English Installation and operating instructions Energy meter 3-phase CETS-A via up to 1500A Description The CETS-A is a compact electronic active power energy meter for application in 3-phase power lines
More information