(S)ATA- and SCSI- PCI and cardbus serial ATA / IDE controller from page 208 PCI express serial ATA / IDE controller from page 209 Removeable frames for serial ATA from page 212 Serial ATA and SAS cable from page 217 IDE-, Floppy and flatcables from page 218 External SCSI connection cable & terminators from page 221 DIGITUS PCI and cardbus serial ATA / IDE controller & adapter...208 DIGITUS PCI express serial ATA / IDE controller...209 DIGITUS Cardbus, express card serial ATA controller and adapter...210-211 Removeable frames for Serial ATA...212 Removeable frames for IDE...213 DIGITUS Enclosure for serial ATA harddisks...214 Serial ATA cable...215-216 Serial ATA and SAS Cable...217 IDE- flat and roundcables...218 IDE-, Floppy and flatcables...219 Interne SCSI UW flatcables and external SCSI cables...220 External SCSI connection cables and terminators...221 SCSI terminators and adapter...222 Network Attached Storage and iscsi modules...223-224 207
DIGITUS PCI and cardbus serial ATA / IDE controller DIGITUS Serial ATA 150 PCI Add-On card, 2-port Conforms to Serial ATA 1.0 specification, revision 2.2 Stand-alone PCI to serial ATA host controller Supports hard drives larger than 137GB Conforms to PCI IDE Controller specifikation, revision 1.0 Supports spread spectrum Conforms to the programming interface for Bus Master IDE Controller, revision 1.0 standard Two independent serial ATA channels Serial ATA generation 1 data transfer rate up to 150MB/sec Operating system support for Win9X, Win ME, NT4, Win2K and XP 2 x serial ATA connections 194583 / DCST SATA150-2D Serial ATA PCI controller, 2-port Serial ATA 150 PCI Add-On Card, 4-port raid Conforms to Serial ATA 1.0 specification, revision 2.2 Stand-alone PCI to serial ATA host controller Supports hard drives larger than 137GB Conforms to PCI IDE Controller specification, revision 1.0 Supports spread spectrum Conforms to programming interface for Bus Master IDE Controller, revision 1.0 standard Four independent serial ATA channels for simultaneous connection of one serial ATA device each Supports the following Raid Levels: 0 = Disk Striping, 1 = Disk Mirroring, 1+0 = Combination of disk striping and disk mirrorin Serial ATA generation 1 data transfer rate up to 150MB/sec Operating system support for Win9X, Win ME, NT4, Win2K and XP 157946 / AC-SATA150-4R Serial ATA 150 PCI Add-On card, 4 device DIGITUS ATA 133 IDE RAID controller, PCI Two connections for a maximum of four IDE hard drives UDMA-6 ATA 133, 100, 66, 33 compatible Windows 98SE / NT 4.0 / 2000 / XP Supports the following Raid levels: 0 = Disk striping, at least one hard drive is required 1 = Disk mirroring, at least two hard drives are required 1+0 = Combination of disk striping and disk mirroring, at least four hard drives are required With configurable disk stripe set size. Accessory Accessory 191063 / DCST ATA133RAID-4700 ATA 133 IDE raid controller, PCI 32 Bit Serial ATA to ultra ATA adapter, horizontal Allows the use of ATA hard drives with a serial ATA controller Stand alone Serial ATA to Ultra ATA bridge board Design Conform to Serial ATA 1.0 Specifications, Revision 2.2 Supports PIO mode 0-4 UDMA 66,100, and 133 support Serial ATA Powermanagement Compact dimensions for direct connection to ATA hard drives Deliverable in horizontal version 205463 / AB-SATA-IDE Serial ATA to ULTRA ATA adapter, horizontal 208
DIGITUS PCI express serial ATA / IDE controller DIGITUS Serial ATA II PCI express card 1 x external esata and 1 x internal SATA Port int / ext Ports selectable by configuration Compliant with PCI Express Base Specification 1.0a Compliant with Serial ATA 1.0a specification and with full complement of Serial ATA II optional features Installs in any available PCI Express slot with different lane width Supports data transfer up to 300 Mbps Supports NCQ (Native Command Queuing) Hot-Plug and Hot-swapping feature Supports Windows 2000 / XP / Server 2003 / Vista 205036 / DC-30101 Serial ATA II PCI express card DIGITUS Serial ATA II PCI express card 2 x external esata and 2 x internal SATA Ports int / ext Ports selectable by configuration Compliant with PCI Express Base Specification 1.0a Compliant with Serial ATA 1.0a specification and with full complement of Serial ATA II optional features Installs in any available PCI Express slot with different lane width Supports RAID level 0,1 0+1 Supports data transfer up to 300 Mbps Supports NCQ (Native Command Queuing) Hot-Plug and Hot-swapping feature Supports Windows 2000 / XP / Server 2003 / Vista 205043 / DC-30102 Serial ATA II PCI express card DIGITUS Serial ATA II / PATA PCI express card 2 x external esata and 2 x internal SATA Ports 1 x internal parallel ATA port - supports up to UDMA-6 transfer mode and up to 4 devices int / ext Ports selectable by configuration Compliant with PCI Express Base Specification 1.0a Compliant with Serial ATA 1.0a specification and with full complement of Serial ATA II optional features Supports data transfer up to 300 Mbps Supports RAID level 0,1 0+1 Installs in any available PCI Express slot with different lane width Supports NCQ (Native Command Queuing) Hot-Plug and Hot-swapping feature on SATA ports Supports Windows 2000 / XP / Server 2003 / Vista 205050 / DC-30103 Serial ATA II / PATA PCI express card Realtime backup system for SATA harddisks Hardware solution for on line redundant data backup Easy installation, automatic configuration, and highest possible reliability Independent from the installed operating system - works with Windows, MacOS, Linux, Unix, etc. RAID Level 1 (disk mirroring) The system harddisk is mirrored in realtime on a second backup harddisk Automatic configuration and data rebuilding after a harddisk crash Black coloured metal housing for assembling in a 3,5 drive bay (incl. additional faceplate in beige colour) Harddisk status monitoring using six LEDs Acoustic alarm (on / off switchable) SATA connectors for motherboard, system- and backup-harddisk Accessory Accessory 205814 / AB-SATA-BK SATA Harddisk realtime backup system 209
DIGITUS Cardbus, express card serial ATA controller and adapter DIGITUS Serial ATA 150 PC-Card, 2 connections Conforms to Serial ATA 1.0 specification, revision 2.2 32 bit PC Card, card bus Type II compatible Stand alone PCI to Serial ATA host Controller Supports hard drives larger than 137GB Two independent serial ATA channels, for simultaneous connection of one serial ATA device each Serial ATA generation 1 data transfer rate up to 150MB/sec Operating system support for Win9X, Win ME, NT4, Win2K and XP 205456 / DC-32101 Serial ATA 150 PC-Card, 2 connections DIGITUS esata II 300 ExpressCard 1 x esata port ExpressCard/34 form factor Data transfer rate up to 300 Mbps Support device hotswapping Compliant with ExpressCard 1.0 specification Supports Native Command Queuing (NCQ) Supports Windows 2000 / XP / Server 2003 / Vista 205098 / DC-31101 esata II 300 ExpressCard DIGITUS Cardbus to PCI adapter-cards Compliant with PC Card Rel. 8.0 and PCI 2.2 Specification Support PCMCIA 2.1 and Cardbus PC card with 3,3V / 5V operation One PC card slot for (Type I/II/III PCMCIA card) Accessory Accessory 103462 / DN-7002 Cardbus to PCI adapter-card DIGITUS ExpressCard to PCI Express adapter card Shares ExpressCard notebook extensions with the PC Supports ExpressCard 34 and 54 form factor size Compliant with PCI Express Base Specification 1.0a 1,5V / 3,3V LED indicator Installs in any available PCI Express slot with different lane width No additional driver software required 205074 / DC-30401 ExpressCard to PCI Express adapter card 210
DIGITUS drive device controller Accessory DIGITUS 2.0 IDE & SATA cable Support 1,8 /2,5 /3,5 IDE and Serial ATA HardDisk Support SATA, SATA II Compliance with 2.0 (Hi-Speed) Compliance with Mass Storage Class Support 480Mbps High Speed (HS) and 12Mbps Full Speed operation Support ATA/ATAPI Ultra DMA Mode Support ATA/ATAPI PACKET command feature set Support ATA/ATAPI LBA48 bit addressing mode Support dual LUN (Logic Unit Number) with automatically master/slave enumeration High-Speed Data Transfer, Low Power Consumption Red / green LED s indicating operation Operating System Support: Windows 98SE/ME/2000/XP/2003/Vista 195580 / DA-70148 2.0 IDE & SATA cable DIGITUS 2.0 SATA adapter Easily connect external SATA, SATAII hard disk with No extra driver needed incl. extension cable, esata to SATA and esata to esata cable Support OS: Windows 2000 / XP / Vista MacOS/9 (9.2.2 recommendations) and 10.2.8 or 10.3 OSX recommendation 205388 / DA-70149 2.0 SATA adapter DIGITUS 2.0 to IDE adapter cable 2.0 compliant Support for ATA / ATAPI devices Cable length 1,2m inclusive 2,5 Adapter Support for: Windows XP, Windows 2000/Vista Accessory 171003 / DA-70147 2.0 to IDE adapter cable 211
Removeable frames for serial ATA DIGITUS Serial ATA hard drive removable frame Hard drive removable frame for installation in 5.25 PC drive bays For 3,5 Serial ATA hard drives Material: plastic Lockable With status LED 1 additional fan integrated 194163 / DA-50214-A SATA removable frame Premium hard drive removable frame SATA 150 High quality hard drive removable frame 5.25 for 3.5 S-ATA150 hard drives Metal housing with plastic panel, better EMI / RFI protection Integrated bottom fan Drawer lockable With status LED 205401 / A-ATN900 SATA 150 removable frame Accessory Premium hard drive removable frame SATA 150 with LC display High quality hard drive removable frame 5.25 for 3.5 S-ATA150 hard drives Metal housing with plastic panel, better EMI / RFI protection LC Display shows internal operating temperature and fan speed Adjustable overheating alarm Integrated fan Drawer lockable With status LED Accessory 205418 / A-ATN910 SATA 150 removable frame with LCD 212
Removeable frames for IDE DIGITUS IDE hard disk removable frame Hard disk removable frame 5.25 siutable for 3.5 hard drives Material: plastic Frames are equipped with an additional fan (one further fan for the drawer can also be fitted) Lockable drawer With status LED Accessory 194149 / DA-50211-A Removable Frame, ATA100, 40-pin 194156 / DA-50212-A Drawer, ATA 100, CENT 36 Premium hard drive removable frame ATA 133 High quality hard drive removable frame 5.25 for 3.52 ATA 133 hard drives Metal housing with plastic panel, better EMI / RFI protection Integrated fan Drawer lockable With status LED 205432 / A-ATN901 ATA 133 removable frame Premium hard drive removable frame ATA 133 High quality hard drive removable frame 5.25 for 3.5 ATA 133 hard drives Metal housing with plastic panel, better EMI / RFI protection LC Display shows internal operating temperature and fan speed Adjustable overheating alarm Integrated fan Drawer lockable With status LED Accessory 205449 / A-ATN911 ATA 133 removable frame 213
DIGITUS Enclosure for serial ATA harddisks DIGITUS Serial ATA II 4 x HDD box 4 x HDD Box with JBOD (Just A Bunch Of Disk) mode: Combining multiple physical disk drives into a single virtual one. 2 to 4 disks can be merely concatenated, end to beginning, so they appear to be a single large disk. Used to turn several odd-sized drives into one big volume. For example JBOD could use a 300GB, 500GB, 400GB and 200GB drive to combine into a logical drive at 1.4TB (max. up to 2TB), which is often more useful than the individual drives separately. SATA II Interface - 3Gb/s Support RAID level 0,1 Supports 3,5 and 2,5 HDD (2.5 with optional adapter) Power ON/OFF switch Cooling Fan ON/OFF switch with LED JBOD mode with LED indication Supported OS: Win 98SE/ ME/ 2000 SP-3/ XP > SP-1, Vista, Mac OS 10.3.9/ 10.4 Dimensions: 135 mm x 128 mm x 248 mm Power supply: Input 100V-240V AC, Output +5V 4.0A/ +12V 6.0A (max.) 205395 / DA-70531 Serial ATA II 4 x HDD box DIGITUS 3.5 External aluminium HDD enclosure SATA to SATA Serial ATA 1.0 compliant Automation 3.0/1.5Gbps transmission rate negotiation Support S-ATA hot-plug Support S-ATA connector Thinner and longer cable Serialize/ Deserialize a 40 bit (double word aligned) or 10 bit with 4X speed signal from/to the link layer Provide specified OOB signal detection and transmission 32 bits CRC error checking on all data and control information Supports 32 bits and 48 bits LBA hard disk Compatible with WIN98, WIN98se, WIN 2000, WIN ME, WIN XP, WIN Vista Support MAC OS which support S-ATA HDD Support LINUX OS which support S-ATA HDD Accessory Accessory 192121 / DA-70513-1 3.5 Aluminium HDD enclosure SATA to SATA 192138 / DA-70514-1 3.5 Aluminium HDD enclosure SATA to SATA / 2.0 214
Serial ATA cables Serial ATA connection cable Suitable for data transfer up to 300 MB/s 7-wire cable, UL21149 152712 / AK-SATA-030 0,30 m 121121 / AK-SATA-050 0,50 m 121695 / AK-SATA-075 0,75 m 121138 / AK-SATA-100 1,00 m Serial ATA connection cable with left angled connector Suitable for data transfer up to 300 MB/s 7-wire cable, UL21149 male connector 90 angled 154242 / AK-SATA-030DL 0,30 m 153191 / AK-SATA-050DL 0,50 m 153214 / AK-SATA-075DL 0,75 m DIGITUS Blister serial ATA power cable Serial ATA power supply cable 15-pin SATA power supply / female - 4-pin ATX power supply / female in blisterpackage 131939 / DB-129653 0,15 m Serial ATA power cable Serial ATA power supply cable 15-pin SATA power supply / female - 4-pin ATX power supply / female 129653 / AK-SATA-PC 015 0,15 m DIGITUS Blister slotbracket with SATA connector Compliant with Serial ATA Standard Support for data transfer rate up to 300 MB/s 7-wired cabel, UL21149 4 x Data, 3 x Ground Cable length 0,50m in blisterpackage 206651 / DB-180197 Slotbracket 1 SATA connector 206682 / DB-180203 Slotbracket 2 SATA connectors Slotbracket with SATA connector Compliant with Serial ATA Standard Support for data transfer rate up to 300 MB/s 7-wired cabel, UL21149 4 x Data, 3 x Ground Cable length 0,50m 180197 / AK-SATA-SB1 Slotbracket 1 SATA connector 180203 / AK-SATA-SB2 Slotbracket 2 SATA connectors Accessory Accessory 215
Serial ATA cables Serial ATA connection cable with power connector Accessory Accessory Suitable for data transfer rates up to 300 MB/s 7-wire cable, UL21149 4 x data wires, 3 x earthing wires 4-wire cable, 4 power supply / female (12V, GND, 5V, GND) 22-pol. SATA male - 7-pol. SATA male a. 4-pol power supply male 154266 / AK-SATA-SP-050 0,50m 154273 / AK-SATA-SP-075 0,75 m 154280 / AK-SATA-SP-100 1,00 m Serial ATA connection cable with power connector Suitable for data transfer rates up to 300 MB/s 7-wire cable, UL21149 4 x data wires, 3 x earthing wires 4-wire cable, 4 power supply / female (12V, GND, 5V, GND) 22-pol. SATA male - 7-pol. SATA male a. 4-pol power supply male 159940 / AK-SATA-SP-050B LEDcolor blue 159957 / AK-SATA-SP-050Y LED color yellow 159964 / AK-SATA-SP-050R LED color red 159971 / AK-SATA-SP-050G LED color green 159988 / AK-SATA-SP-050W LED color white DIGITUS Blister serial ATA connection cable with metal latch Suitable for data transfer up to 300 MB/s 7-wire cable, UL21149 Provide a safe connection between Harddisk and Mainboard in blisterpackage 196617 / DB-183020 0,30 m 196624 / DB-183037 0,50 m 196631 / DB-183044 0,75 m 196655 / DB-187592 1,00 m Serial ATA connection cable with metal latch Suitable for data transfer up to 300 MB/s 7-wire cable, UL21149 Provide a safe connection between Harddisk and Mainboard 183020 / AK-SATA-030-L 0,30 m 183037 / AK-SATA-050-L 0,50 m 183044 / AK-SATA-075-L 0,75 m 187592 / AK-SATA-100-L 1,00 m DIGITUS External Serial ATA connection cable (esata) with metal latch Suitable for data transfer up to 300 MB/s 7-wire cable, UL2725, braid shielded Provide a safe connection between PC and HDD-enclosure in blisterpackage 197164 / DB-193821 0,75 m 197188 / DB-193845 1,00 m 197171 / DB-193838 1,50 m External Serial ATA connection cable (esata) with metal latch Suitable for data transfer up to 300 MB/s 7-wire cable, UL2725, braid shielded Provide a safe connection between PC and HDD-enclosure 193821 / AK-ESATA-075 0,75 m 193838 / AK-ESATA-100 1,00 m 193845 / AK-ESATA-150 1,50 m 216
Serial ATA and SAS cables DIGITUS Blister serial ATA adapter cable (esata to SATA) with metal latch Suitable for data transfer up to 300 MB/s 7-wire cable, UL2725, braid shielded SATA (L-Typ) connector to esata (I-Typ) connector Provide a safe connection between PC and HDD-enclosure in blisterpackage 197195 / DB-193852 1,00 m 197201 / DB-193869 1,50 m Serial ATA adapter cable (esata to SATA) with metal latch Suitable for data transfer up to 300 MB/s 7-wire cable, UL2725, braid shielded SATA (L-Typ) connector to esata (I-Typ) connector Provide a safe connection between PC and HDD-enclosure 193852 / AK-ESATA-SATA100 1,00 m 193869 / AK-ESATA-SATA150 1,50 m DIGITUS Blister slotbracket with esata connector Compliant with Serial ATA Standard Support for data transfer rate up to 300 MB/s SATA (L-Type) Mainboard connector to esata (I-Typ) Slot female connector 7-wired cabel, UL21149 Cable length 0,50 m in blisterpackage 197218 / DB-193807 Slotblech 1 esata port 197225 / DB-193814 Slotblech 2 esata port Slotbracket with esata connector Compliant with Serial ATA Standard Support for data transfer rate up to 300 MB/s SATA (L-Type) Mainboard connector to esata (I-Typ) Slot female connector 7-wired cabel, UL21149 Cable length 0,50m 193807 / AK-ESATA-SB1 Slotbracket 1 esata connector 193814 / AK-ESATA-SB2 Slotbracket 2 esata connectors SATA to serial attached SCSI (SAS) - connection cable Connects four Serial ATA devices to a SAS controller 4 x SATA connector with metal latch 1 x SAS controller connector 32-pin Length 0,5 m 205142 / AK-SAS-01 SATA to SAS connection cable, 0,50 m Accessory SATA to serial attached SCSI (SAS) - connection cable Connects four Serial ATA devices to a SAS controller 4 x SATA connector with metal latch 1 x SAS controller connector 32-pin 1 x connection cable for drive cage LEDs (2 x 3-pin female header) Length 1,0 m 205159 / AK-SAS-02 SATA to SAS connection cable, 1,0 m Accessory 217
IDE- flat and roundcables ATA Hard drive connection cable, round cable design 80-wire cable in plastic sheath, AWG 30 Jacket and hoods in grey, material PVC 40-pin IDC in various colours (blue = controller, black = master, grey = slave) 092919 / AK-ATA-100/ROUND-LC 0,60 m ATA 133 Hard drive connection cable, round cable design 80-wire cable, twisted pair, AWG 30 (TPE), UL 20297 Booths in black, sheath transparaent, material PVC, foil and braid shielding 40-pin IDC in various colours, (blue = controller, black = master, grey = slave) Seperate Earthwire with terminal IDC connector with pulling support 106234 / AK-ATA133-1ROUND 0,45 m 106241 / AK-ATA133-2ROUND 0,60 m 106258 / AK-ATA133-3ROUND 0,90 m DIGITUS Blister hard drive connector cable for 2 x IDE / AT bus hard drives 3 x 40-pin, socket connector 40-wire ribbon cable, AWG28, 2.54 mm pitch, UL2651 in blisterpackage Accessory Accessory 074298 / DB-064084 0,50 m 074182 / DB-063193 0,70 m Hard drive connector cable for 2 x IDE / AT bus hard drives 3 x 40-pin, socket connector 40-wire ribbon cable, AWG28, 2.54 mm pitch, UL2651 064084 / AK 5430 0,50 m 063193 / AK 336 0,70 m 218
IDE-, floppy and flatcables DIGITUS Blister ultra ATA hard drive connector cable 100 Mbps For Ultra DMA, Ultra DMA 2 and Ultra ATA hard drives up to 100 Mbps. 80-wire ribbon cable, AWG30, 0.635 mm pitch, UL2678, three differently colored 40-pin socket connectors (blue= controller, black= master, grey= slave) in blisterpackage 082248 / DB-079163 0,46 m 082255 / DB-079156 0,60 m Ultra ATA hard drive connector cable 100 Mbps For Ultra DMA, Ultra DMA 2 and Ultra ATA hard drives up to 100 Mbps. 80-wire ribbon cable, AWG30, 0.635 mm pitch, UL2678, three differently colored 40-pin socket connectors (blue= controller, black= master, grey= slave). 079163 / AK-ATA-100 0,46 m 079156 / AK-ATA-100/1 0,60 m 3.5 FLOPPY connector cable for 2 x 3.5 FDD 3 x 34-pin, socket connector (3.5 ) 34-wire ribbon cable, AWG28, 2.54 mm pitch, UL2651 078043 / AK 3620-050 0,50 m 063438 / AK 3620 0,75M 0,75 m Ribbon cable AWG28, 1.27 mm pitch Colour grey with red marked ID line 30.5 meter roll AK AWG68 = Pitch 0.638 mm Crimping tool for IDC plugs and socket connectors Stable steel design with plastic grip sleeves For connector heights from 6 to 27.5 mm Accessory 051220 / AK AWG20 20-wires 051251 / AK AWG26 26-wires 051268 / AK AWG34 34-wires 051275 / AK AWG40 40-wires 051299 / AK AWG50 50-wires 052210 / A-SK IDC Crimping tool Accessory 219
Internal SCSI UW flatcables and external SCSI cable Internal SCSI UW 320 ribbon cable 68-wire twisted pair cable, AWG 30, 0.635 mm pitch, with 135 mm twist. 105985 / AK 347/L320 0,675 m 105992 / AK 350/L320 0,810 m 106005 / AK 3505/L320 0,945 m 106012 / AK 346/L320 1,350 m Internal SCSI UW 320 ribbon cable, with active terminator 68-wire twisted pair cable, AWG 30, 0.635 mm pitch, with 135 mm twist, active termination. 106029 / AK 34-3L320 0,675 m 106036 / AK 34-4L320 0,810 m 106043 / AK 34-5L320 0,945 m 106050 / AK 34-6L320 1,080 m 106067 / AK 34-7L320 1,215 m 106074 / AK 34-8L320 1,350 m SCSI 3 SCSI 3 cable, UL 2919 DSUB 68, HP, male DSUB 68, HP, male screw screw UL 2919, twisted pair, triple shielding, 68-wire, molded hoods 064336 / AK 5800/F-1 0,90 m 064343 / AK 5800/F-2 2,00 m SCSI 2 SCSI 2 cable, UL 2919 DSUB 50, HP, male DSUB 50, HP, male clip clip UL 2919, twisted pair, triple shielding, 50-wire,molded hoods. AK 347/L320 = 3 x IDC 68, male AK 350/L320 = 4 x IDC 68, male AK 3505/L320 = 5 x IDC 68, male AK 346/L320 = 8 x IDC 68, male AK 34-3L320 = 3 x IDC 68, male AK 34-4L320 = 4 x IDC 68, male AK 34-5L320 = 5 x IDC 68, male AK 34-6L320 = 6 x IDC 68, male AK 34-7L320 = 7 x IDC 68, male AK 34-8L320 = 8 x IDC 68, male 064268 / AK 579/F-2 2,0 m Accessory Accessory SCSI 2 SCSI 2 cable, UL 2990 DSUB 50, HP, male DSUB 50, HP, male clip clip UL 2990, twisted pair, double shielding, 50-wire, molded hoods 064237 / AK 578 0,9 m 064244 / AK 579 3,0 m FAST SCSI 1 SCSI 2 cable, UL 2919 CENT 50, SP, male DSUB 50, HP, male clamp clip UL 2919, twisted pair, triple shielding, 50-wire, molded hoods 064121 / AK 545/F-2 2,0 m 220
External SCSI connection cables and terminators SCSI 1 SCSI 2 cables, UL 2990 DSUB 25, SP, male DSUB 50, HP, male screw clip UL 2990, twisted pair, double shielding, 25-wire, molded hoods, for ZIP drives 063766 / AK 438-1NEW 0,9 m SCSI 1 SCSI 2 cable, UL 2990 CENT 50, SP, male DSUB 50, HP, male clamp clip UL 2990, twisted pair, double shielding, 50-wire, molded hoods. 064107 / AK 545 2M 2,0 m Very high density SCSI cable, UL 20276 DSUB 68, HP, male CENT 68, VHD, male screw pitch 0.88 mm, screw UL 20276, twisted pair, double shielding, 68-wire, molded hoods 082095 / AK 660 0.90M 0,9 m Internal LVD 320 terminator DSUB 68-pin, HP, female LVD 320 108924 / AB LVD-320T active External LVD 320 terminator, with LED DSUB 68-pin, HP, male, screw LVD/SE 320 with LED, active 129448 / AB EXT320 active, LVD/SE Internal SCSI 3 terminator, active DSUB 68, HP, female Single-ended, active Accessory Accessory 060444 / AB 774 active 221
SCSI terminators and adapter Internal SCSI 2 terminator 50-pin, SP, Box header Single-ended 060390 / AB 770 active Internal mini SCSI adapter 50-pin socket connector, SP DSUB 68-pin, HP, female Molded version 060826 / AB 845/MOLDED Internal mini SCSI adapter 50-pin box header, SP DSUB 68-pin, HP, male Molded mini version 060802 / AB 844/MOLDED SCA adapter, internal Internal 1: SCA CENT 80-pin, HP, female Internal 2: DSUB 68-pin, HP, female With 4-pin power supply plug and ID connector 061182 / AB SCA-2 active Accessory Accessory SCA multi adapter, internal, with termination Internal 1: SCA CENT 80-pin, HP, female Internal 2: 50-pin box header Internal 3: DSUB 68-pin, HP, female With 4-pin power supply plug and ID connector 061199 / AB SCA-3 active SCSI adapter internal external, on slot bracket Internal: DSUB 68-pin, HP, female External: DSUB 68-pin, HP, female, slot bracket, clip fastening 060789 / AB 843 222
Network attached storage and iscsi modules Open-E NAS, network attached storage modul Web-based graphical user interface, preinstalled in flash memory for operation of an IDE connection File management with supporting journaling function SSL secured administrator access Access control via Access Control List (ACL) LDAP for one-time user / user group and access definition Supported network transport protocols: TCP/IP and NetBEUI Supported network file protocols: SMB, CIFS (file sharing Windows based); NFS (file sharing Linux / Unix based); FTP (operating system independent); Apple Talk Supported clients: Microsoft Windows, Linux, Unix and Apple OS X Under Windows 2000, the Directory features of the NT primary domain contoller are supported in compatibility mode DHCP server support RAID controllers from the following companies are supported: AMCC storage (3ware), Adaptec and ICP Vortex Built-in snapshot function (depiction of the current file system with directory structure and files) UPS support via serial connection No individual licenses required for clients or servers AB OPEN-E NAS SOHO: Web-based GUI, file system with journal function, Windows Directory, ACL, LDAP, standard gateway support, DHCP server, SSL, SMB / CIFS, FTP, Apple Talk, Microsoft Windows, Apple OS X and Linux client, IDE interface support, simple sharing function, TCP/IP support, snapshot function AB OPEN-E NAS 2.0: in addition to AB OPEN-E NAS SOHO with: NFS support, Unix client support, UPS and hardware RAID controller support AB OPEN-E NAS ENTERPRISE: in addition to AB OPEN-E NAS 2.0 with: Support for more than 2 network cards, backup client support (Veritas, CABrightstor ARCserve, Dantz, Backbone, built-in streamer support and data cloning - disaster recovery), expan ded snapshot function with task planner, LCD support, multiple administrator rights, SNMP for UPS, UPS network and cable support, option span & stripe (for disk prepration), quotas for users, no individual licenses required AB OPEN-E NAS SOHO AB OPEN-E NAS AB OPEN-E NAS SOHO ENTERP Accessory Accessory 160670 / AB OPEN-E NAS SOHO Network attached storage modul 160687 / AB OPEN-E NAS Network attached storage modul 160694 / AB OPEN-E NAS ENTERP Network attached storage modul 223
Network attached storage and iscsi modules Storage software modules for iscsi The Open-E ISCSI software turns a computer system into an iscsi Target Module (ITM). ITM is a cost effective alternative to Fibre Channel Storage Area Networks (SANs) while allowing low-cost centralization of storage without the usual expense and incompatibility normally associated with Fibre Channel (SANs). Unlike Fibre Channel SAN, iscsi can run block-level i/o data over existing Ethernet networks. AB OPEN-E ISCSI SOHO AB OPEN-E ISCSI SMB Open-E ISCSI SOHO Easy iscsi solution for Small Office and Home Office Networks, Web-based graphical user interface, pre-installed on bootable IDE Flash module, Supported network clients: Microsoft Windows, Linux, Unix, Apple OS X and Novell, Secured Administration Access with various permission levels, Standard gateway support, DHCP server support, Online Logical Volume expansion, Multiple Logical Volume Groups for Logical Volumes, Email notificati on, Console tools, Password protection for Targets, no extra client or server licenses required Open-E ISCSI SMB Professional iscsi solution for cost-effective RAID systems. Additional features:, Hardware RAID controller support, Snapshot for real-time image of one Logical Volume, UPS support for Serial and devices, 10Gb Ethernet support, TCP/IP Offload Engines support, Up to 2 CPU support, no extra client or server licenses required Open-E ISCSI ENTERPRISE High-level iscsi solution for Enterprise storage requirements. Additional features:, Multi-Snapshot with Scheduling Function for snapshots at predefined points in time, Support for Multiple Network Cards, Adapter Fault Tolerance (AFT) assuring greater reliability in the network, Adaptive Load Balancing (ALB) for more bandwidth in the network, Multiple administrator rights levels, Fibre Channel support, Network UPS support, IPsec for securing IP communications by encrypting, Multi-CPU support, no extra client or server licenses required AB OPEN-E ISCSI ENTE Accessory Accessory 193579 / AB OPEN-E ISCSI SOHO ISCSI modul SOHO 193067 / AB OPEN-E ISCSI SMB ISCSI modul SMB 193074 / AB OPEN-E ISCSI ENTE ISCSI modul ENTERPRISE 224