SUMMARY - RELATIONSHIP BETWEEN QUALITY OF SERVICE DEMANDED AND TARIFF



Similar documents
ESB Networks Response. ERGEG Consultation. Voltage Quality Regulation in Europe

A Network Reference Model for Distribution Regulation and Planning: the Spanish Case

Phase Attribute Identification using GPS Technology

SURVEY OF HARMONIC DISTORTION IN LV AND MV NETWORKS: RESULTS AND CORRECTIVE STRATEGIES

Power products and systems. Intelligent solutions for power distribution Zone concept

Low Voltage Asset Management (LVAM) The key to reliable and safe electricity

Chapter 1. Network Structures

BL20A0501 Electricity distribution technology. Introduction Jarmo Partanen

VOLTAGE CONTROL IN DISTRIBUTION SYSTEMS AS A LIMITATION OF THE HOSTING CAPACITY FOR DISTRIBUTED ENERGY RESOURCES

ELECTRICITY DISTRIBUTION TARIFFS The Chilean Experience. Hugh Rudnick Pontifícia Universidad Católica de Chile

Medium Voltage (MV) & High Voltage (HV) Training Module 6. Date of the presentation

Agenda do Mini-Curso. Sérgio Yoshio Fujii. Ethan Boardman.

For a phase-to-phase voltage between 100 V and 1000 V. The standard ratings are: 400 V V V (at 50 Hz)

ES281 COMPANY-SPECIFIC APPENDICES TO ENA ENGINEERING RECOMMENDATION G81 PART 1

Understanding Power Factor and How it Affects Your Electric Bill. Presented by Scott Peele PE

Comparative Report. Pacific Region Electricity Bills

Audit Report Rottnest Island 2015 Network Quality and Reliability of Supply Performance Audit - Operation of Compliance Monitoring Systems

Developing a Utility/Customer Partnership To Improve Power Quality and Performance

BC Hydro. Electric Distribution System Cost of Service Study

How the National Grid System Operates. Chris Gorman Lead Account Executive Syracuse

Trends in Power Quality

ESB Networks Ltd Statement of Charges

F.C. Chan General Manager, CLP Engineering Ltd., Hong Kong SAR, China

Networks. ESB Networks Ltd Basis of Charges for Connection to the Distribution System. Commercial and Customer Asset Management ESB Networks Ltd.

Comparison of GIS and AIS systems for urban supply networks

Isolated-Parallel UPS Configuration

Enel s experience on smart grids

Energy Storage Systems in Grid4EU Demo4 and in Other Enel Distribuzione Projects Speaker

The calm after the storm

SGTech Europe 2015 September 22 th Amsterdam. Pedro Gama, Head of SCADA & Telecom Department at EDP Distribuição, SA

ADMS(Advanced Distribution Management System ) in Smart Grid

Reliability centered asset management tool

Network Consulting for Power Grid Optimization

Advanced Protection of Distribution Networks with Distributed Generators

Medium voltage products UniSec for Smart Grid Air-insulated medium-voltage secondary distribution switchgear

Simple Methods for Calculating Short Circuit Current Without a Computer By Dennis McKeown, PE GE Senior System Application Engineer

Proceedings of the 38th Hawaii International Conference on System Sciences

THE PER-UNIT SYSTEM. (2) The per-unit values for various components lie within a narrow range regardless of the equipment rating.

AMSC s Superconductor Cable Technologies for Electric Utilities

Electricity Networks Service Standards: An Overview

NO-BREAK KS 7e. Concentrated Energy kva (50Hz) 3000 kva (60Hz) DIESEL ROTARY UNINTERRUPTIBLE POWER SUPPLY SYSTEM

7. Reactive energy compensation

4160: THE GREEN 480 MEDIUM VOLTAGE ELECTRICAL SYSTEMS

Calculation of Voltage Sag Indices for Distribution Networks

INTEGRAL REMOTE MANAGEMENT SOLUTION cirwatt b series

APPLICATION NOTE USING A MODEL 3060-MS SERIES AS A REGENERATIVE AC SOURCE FOR PV INVERTER TEST APPLICATIONS. Abstract.

Network Pricing Trends

OPERATIONS CAPITAL. The Operations Capital program for the test years is divided into two categories:

Modeling of PV Based Distributed Generator Systems with Diverse Load Patterns

V N ovember Distribution Network Asset Data Available To Third Parties

Market Growth and New Regulations Demand Network Modernization

MEDIUM VOLTAGE. Michael Mosman, PE. CCG Facilities Integration Incorporated FACILITIES INTEGRATION INCORPORATED

Laboratory 4: Feedback and Compensation

RF data receiver super-reactive ASK modulation, low cost and low consumption ideal for Microchip HCS KEELOQ decoder/encoder family. 0.

This is a Master s degree level apprenticeship which includes academic learning combined workplace learning and training.

C. PROCEDURE APPLICATION (FITNET)

Understanding Power Impedance Supply for Optimum Decoupling

Electricity Industry Code. made under the Electricity Act 1994

Reduction of Power Losses Using Phase Load Balancing Method in Power Networks

Benchmark Regulation and Efficiency of Electricity Distribution

Cost Benefit Methodology for Optimal Design of Offshore Transmission Systems

WHITEPAPER CABLE CONDUCTOR SIZING

Analysis of the Brazilian Data Center Power Supplies Market

Phase Balancing of Distribution Systems Using a Heuristic Search Approach

Iman Ziari. M.Sc, B.Eng (Electrical Engineering) A Thesis submitted in Partial Fulfillment of the Requirement for the Degree of. Doctor of Philosophy

How To Choose A Transformer

Electric Power Distribution

Electricity Service Standards

A Case Study: How a Utility Automated and Integrated Data/Control for 4000 Pole-Top Switches and Protection Relays, and Reduced its SAIDI

ZONE SELECTIVE INTERLOCKING (ZSI) APPLICATION AND TESTING GUIDE SIEMENS WL UL489 AND UL1066 AIR CIRCUIT BREAKERS

Technical Trial of Broadband IP/Internet over ESB Power Networks. Engineers Ireland. October 2006

Transformers. Special transformers Reactors products

Digital to Analog Converter. Raghu Tumati

Washington DC Power Sector Overview

1ED Compact A new high performance, cost efficient, high voltage gate driver IC family

ICM Project Station Infrastructure and Equipment

EMTP STUDIES PERFORMED TO INSERT LONG AC CABLES IN THE FRENCH GRID

Loop Bandwidth and Clock Data Recovery (CDR) in Oscilloscope Measurements. Application Note

ASSET MANAGEMENT LCNI 2014 Wednesday 22 nd October. Jennifer Woodruff Innovation & Low Carbon Networks Engineer

RX-AM4SF Receiver. Pin-out. Connections

Transformers Energy efficient transformer solutions European Minimum Energy Performance Standard (MEPS)

Federal Wage System Job Grading Standards for Electric Power Controlling, Table of Contents

Network Demand and Customer Connections Forecasting Procedure Power Networks

3-PHASE LOW VOLTAGE NETWORK LOAD BALANCER : A COST EFFECTIVE SOLUTION TO LINE VOLTAGE VARIATIONS

Rack mounted telephone- and leased line modem for industrial applications

14.5GHZ 2.2KW CW GENERATOR. GKP 22KP 14.5GHz WR62 3x400V

Fuse Selection Method Module 2. Date of the presentation

Cost-effective Distribution Reliability Improvement Using Predictive Models

MOBILE SYSTEM FOR DIAGNOSIS OF HIGH VOLTAGE CABLES (132KV/220KV) VLF-200 HVCD

3. TYPES OF SERVICE AVAILABLE. 3.1 Scope

Siemens Fusesaver. Highest availability and cost savings for your MV distribution network.

Transcription:

SUMMARY - RELATIONSHIP BETWEEN QUALITY OF SERVICE DEMANDED AND TARIFF PA Consulting Services SA Authors: C. Guidi / J. Espain - / J. García Argentina Restructuring of Electric Sectors in Latin America has been characterized by the concession of service supply, establishing: a) the quality conditions under which such service should be provided; b) a penalty regime in the case of verifying non compliance with such conditions; and c) maximum tariffs to be charges for the service. Thus, in each case, an implicit relationship between the price paid by the customer and the service and the related quality was established. Even though these aspects were evaluated by the different bidders when they submitted their offers for the different areas given in concession, they had no definite experience about the implications of this type of regime, and after a certain period of application, similar concerns started to arise in various countries whether it was possible to provide the service according to the quality demands established and if tariffs really reflected the service supply under those conditions. This situation reached various degrees of relevance depending on the characteristics of the concessions and quality regimes in each country, but in general terms it gave way to the beginning of some research about this particular subject. The natural opportunity has been the moment of the tariff review, which generally takes place every 4 years, counted from the take-over date. predictable quality, have proved to be within the limits established. In some cases, there is evidence of limits way below the admissible ones. Values also presented a significant similitude among themselves and a good relationship with their Distribution Costs. As regards areas, the opposite situation was verified. In most of the cases, the resulting simulation values proved the impossibility of complying with the demand levels established, as well as the presence of a great dispersion among the results obtained, depending mainly on the facilities characteristics, in particular, the feeders length. In these cases, the absence of a relationship between Distribution Costs incorporated in tariffs and the quality of service predicted to be obtained through an efficient network management was verified. In most of the cases it was also verified that the necessary costs to increase quality of service levels are of a magnitude comparable to the Distribution Cost itself, even not making it possible to achieve the demanded levels. Some countries have undertaken studies tending to determine if the typical circuits for each type of area to serve enabled to provide the service according to the requirements established in the quality standards, as well as the economic impact of the standard application regarding the necessary resources for the execution of the requested controls and their relationship with tariff. The results obtained prove that quality requirements might not be in agreement with tariffs in some of the served areas. In some cases, they are even impossible to comply with considering the network configuration considered in tariff determination. This situation has led to more in-depth studies about the actual companies networks in order to determine their relationship with the typical circuits considered for tariff determination and with the quality of service levels demanded. These studies have yielded different results depending on the characteristics of the area served. The conclusions are that in all the cases analyzed for areas, the simulations results as regards the

RELATIONSHIP BETWEEN QUALITY OF SERVICE DEMANDED AND TARIFF Authors: C. Guidi / J. Espain - / J. García PA Consulting Services SA Argentina SYNOPSIS: depending on the characteristics of the area served. These results will be presented in this paper. Restructuring of Electric Sectors in Latin America has been characterized by the concession of service supply, establishing: a) the quality conditions under which such service should be provided; b) a penalty regime in the case of verifying non compliance with such conditions; and c) maximum tariffs to be charges for the service. Thus, in each case, an implicit relationship between the price paid by the customer and the service and the related quality was established. Even though these aspects were evaluated by the different bidders when they submitted their offers for the different areas given in concession, they had no definite experience about the implications of this type of regime, and after a certain period of application, similar concerns started to arise in various countries whether it was possible to provide the service according to the quality demands established and if tariffs really reflected the service supply under those conditions. This situation reached various degrees of relevance depending on the characteristics of the concessions and quality regimes in each country, but in general terms it gave way to the beginning of some research about this particular subject. The natural opportunity has been the moment of the tariff review, which generally takes place every 4 years, counted from the take-over date. Some countries have undertaken studies tending to determine if the typical circuits for each type of area to serve enabled to provide the service according to the requirements established in the quality standards, as well as the economic impact of the standard application regarding the necessary resources for the execution of the requested controls and their relationship with tariff. The results obtained prove that quality requirements might not be in agreement with tariffs in some of the served areas. In some cases, they are even impossible to comply with considering the network configuration considered in tariff determination. This situation has led to more in-depth studies about the actual companies networks in order to determine their relationship with the typical circuits considered for tariff determination and with the quality of service levels demanded. These studies have yielded different results RELATIONSHIP BETWEEN QUALITY OF SERVICE DEMANDED AND TARIFF Methodology The quality of service supplied by a distribution company is generally evaluated through a series of performance indicators that monitor service technical and commercial aspects. The present paper focuses on the technical aspects (Technical Service and Product), since they are closely related to the network characteristics and the market they serve. As regards the Technical Product, only the voltage level has been analyzed and as to the Technical Service, outage frequency and duration indicators have been contemplated. In every case and through a simulation, the analysis has been based on the determination of the quality expected to be obtained in networks of various characteristics operated under efficiency conditions and quality has been associated with distribution costs that are representative of those characteristics. The results obtained have been considered through multiple studies made in various countries of Latin America, such as Peru, Chile and Argentina, as a result of a tariff revision or a particular research on the predictable quality conditions. For the purposes of the present analysis, three types of markets served by networks of various characteristics have been selected. High-Density, and. The markets analyzed have turned out to be comparable among themselves, and even though there are peculiarities in the facilities serving them, depending on the company and country analyzed, the main common characteristics in each one of them have been the following: High-density urban market is characterized for being supplied through underground networks and MV/LV transforming modules over 6 kva. Facilities associated to the urban-type market are characterized

by overhead pole networks and MV/LV transforming modules in the order of 3 kva. As regards the rural type market, the facilities characteristics serving it are long-length MV network and small capacity MV/LV transformers. The following figures schematize the representative circuits of each one of the cases under analysis. High-Density Market HV Overhead Pole Two HV transmission line MV HV Line Cliente Especi HV/ MV transf. LV Underground Diversion LV MV/ LV Transf. MV Closure MV Supply Technical Service Interruptions LV MV Supply Underground network Market 1x25 kva Cliente Especi HV/ MV Transf. k1 x 25 MVA MV One HV transmission line Cierre en extremos The analysis tasks performed comprised the simulation of the typical circuit behavior considered in the VAD calculation, in the countries where tariff calculations are based on this methodology and the behavior simulation of the actual networks, operated under efficiency conditions, for the areas that are representative of each one of the markets under study. Simulations comprised the HV and MV network up to the MV/LV terminals, since in average terms 9 % of the interruption impacts undergone by users are originated in these facilities. Through this methodology, maps of the predictable quality could be elaborated through an efficient management of the networks of each MV/LV transforming center, as indicated in the Figure below. LV network Aerial closure MV/ LV. Tranf. LV Network Market

The results of the simulations performed for the different cases analyzed, consolidated by type of market served, are summarized in the figures below. Interruptions Frequency/semester 12 1 8 6 4 2 Duration Time/Semester (hs) 4 35 3 25 2 15 1 5 High Density Max. Freq. Min.Freq. Avge Freq. High Density Max. Time Min. Time Avge. Time Results have proved a great value homogeneity for High-Density cases and a great value dispersion in the case of rural markets, depending mainly on the characteristics of their length. As regards the impact produced on the different voltage level facilities, a high HV network participation has been evident as regards area interruption level, decreasing towards the lower density areas, and showing an insignificant participation in areas. % interruption impact 1% 9% 8% 7% 6% 4% 3% 2% 1% % HV Network. MV Network As regards the participation of the main components of the facilities for each type of network analyzed, the impact of each component in the number and duration of the interruptions has proved to depend mainly on the topology and configuration of each type of network. The following figures show the impact percentage of each element in the Interruption Duration (D) and the Number of Interruptions (N). High-Density Area 9% 6% 46% FUS TRAFOS SECC LINES INTER R6KV 41% 18% 23% 9% % D PARTICIPATION % N PARTICIPATION Area 11% 36% 6% 29% FUS SECC TRAFOS LINES INTER R6KV 29% 3% 4% 5 % D PARTICIPATION % N PARTICIPATION As a result of the comparison of the values obtained with the demand levels established in each particular case, compliance with those values in general terms has been verified in high-density urban areas and urban areas. In the case of areas, non compliance has been verified practically in all demand cases. In the case of areas, various operation and control devices have been incorporated to the simulation in order to improve frequency and duration indicators, such as telecontrol, re-connectors and isolating switches, which were taken into account at the moment of determining the network payment value for the tariff calculation. Technical Product Voltage Level As to Voltage Level, since this parameter is habitually pre-established when the facilities are designed, the results of the simulations run on the typical circuits proved the compliance with design conditions. In the

case of actual networks operated in an efficient way, the values obtained have resulted in voltage drop between 5 % and 7 % for MV network, and between 8 % and 1 % in LV network in areas, and between 8 % and 11 % in the MV network in areas. In the case of areas, it has been necessary to incorporate a simulation of the voltage regulator operation throughout the facilities, resulting in some cases a significant number, that was considered for payment remuneration of the networks at the moment of the tariff calculation. great homogeneity and almost linear relationship among them has turned out for the High-Density area, turning this area into one where both values are perfectly predictable. This situation brings about dispersion areas, depending on the particular features of the networks within which both quality levels and distribution costs are predicted to be. The following graphs represent interruption frequency and time values predictable for each one of the areas under study based on their corresponding distribution costs. 12 Distribution-Related Costs Distribution cost values associated to each one of the facilities that are representative of the areas analyzed present some variations brought about by the various methodologies used for the calculations and to differences in costs, calculation dates and type of related equipment, typical of each company and country studied. Furthermore, the analysis made has performed an adequate value comparison and association, resulting in a value alignment in cases and a huge dispersion in the cases, which might be considered as a reference in the subject. The Figure below represents all quality indicators together, representative of frequency and duration of the interruptions and distribution costs associated to each one of the areas analyzed. Frquency/Semester 12 1 8 6 4 2 Max. Freq. Min. Freq. Avge. Freq. Max. Time Min. Timen Avge. Time 42 35 28 21 14 7 US$/kW-mes Hours/ Semester US$/kW-month It may be observed that even though there is a similar tendency in cost curves with those of the quality of service predictable for each type of networks, the latter show a greater dispersion. Dispersion in quality levels associated to rural areas is due to the fact that the analysis included facilities with very different extensions, in some cases even up to 5 times longer than the lengths between them. The great dispersion in quality levels is not related to the unit capacity costs. As a result of the analysis and by connecting the quality of service values predictable for the various types of networks with the corresponding distribution costs, a Frequency/Semester Hours/Semester 1 8 6 4 2 1 12 14 16 18 2 22 24 US$/kW-month 4 35 3 25 2 15 1 5 1 12 14 16 18 2 22 24 US$/kW-mes The verified linearity for the High Density area may be observed, as well as the increasing value dispersion towards the area. Conclusions To conclude, it may be mentioned that in all the cases analyzed for areas, the simulations results as regards the predictable quality, have proved to be within the limits established. In some cases, there is evidence of limits way below the admissible ones. Values also presented a significant similitude among themselves and a good relationship with their Distribution Costs. As regards areas, the opposite situation was verified. In most of the cases, the resulting simulation values proved the impossibility of complying with the demand levels established, as well as the presence of a great dispersion among the results obtained, depending mainly on the facilities characteristics, in particular, the feeders length. In these cases, the absence of a relationship between Distribution Costs incorporated in tariffs and the quality of service predicted to be obtained through an efficient network management was verified. In most of the cases it was also verified that the necessary costs to

increase quality of service levels are of a magnitude comparable to the Distribution Cost itself, even not making it possible to achieve the demanded levels.