Locks Mortise locks for entrance and internal doors
Products of the G.U-Group for doors
Content Mortise safety locks 2154 2124 2174 2114 Page 10 Page 12 Page 12 Page 14 0024 6031 6206 6043 Page 16 Page 18 Page 20 Page 22 Mortise locks for fire rated doors 1125 1206 2327 2338 Page 26 Page 28 Page 30 Page 32 1795 6065 6138 6306 Page 34 Page 36 Page 38 Page 40 4
Content Mortise locks according to DIN 18251 T1 0215 0415 0515 0615 Page 44 Page 46 Page 48 Page 50 Special locks 0010 0216 0055 1058 Page 54 Page 56 Page 58 Page 60 0353 G353 0371 0372 Page 62 Page 62 Page 64 Page 64 0375 0381H 0381HF 0393 Page 66 Page 68 Page 68 Page 70 5
Content Striking plates B 9000 B 9000 B 9000 B 9000 Page 75 Page 75 Page 76 Page 76 B 9000 B 9000 B 9000 B 9000 Page 77 Page 77 Page 78 Page 78 S403 S404 S407 S411 Page 79 Page 79 Page 80 Page 80 S413 S440 S441 S448 Page 81 Page 81 Page 82 Page 82 6
Content Striking plates S403 S404 S407 S411 Page 83 Page 83 Page 84 Page 84 S412 S413 S440 S441 Page 85 Page 85 Page 86 Page 86 S448 2828 Page 87 Page 87 7
Product features Automatic locking locks Series 21 Latchbolt Assures the best security as additional locking. The integrated lever allows the latchbolt to advance automatically from 12 to 20 mm. Lock case Fully enclosed it protects the function of the lock. As fixing element of the lock with the door. The various design scopes of surfaces and shapes must be specified in the order. Clamping follower Receives the spindle of the door furniture without any play and serves for a reliable lock operation. Fixing holes for door furniture With swarf-guarded bushes, provides for a solid through fixing of the door furniture. Automatic deadbolt Projects automatically by 20 mm and provides an improved locking and security in conjunction with the latchbolt. Must be specified in orders. Locking method May be supplied for profile cylinders or Swiss round cylinders. 8
Product features Mortise safety locks Automatic locking locks Series 21 Application: Entrance house and apartment doors Technical features: profile cylinder lock with latch lever function, optionally also for Swiss round cylinders automatic locking of latchbolt and automatic deadbolt by an integrated level, therefore does not require an auxiliary latch no longer requires manual locking of the door certified security according to VDS class B can be supplied in backsets 55, 60, 65, 70, 80 and 100 mm possibility of through fixing of conventional door furniture such as roses, escutcheons or short backplate sets may be switched in the BUTLER function with free running handle on the inside door, resulting in increased security against burglaries various forend versions in regards to form and optics Lock 0024 + 6031 Application: Entrance house and apartment doors Technical features: profile cylinder lock with latch lever function optionally also as round cylinder lock or short cylinder lock can be supplied in backsets 55, 60, 65, 70 and 80 mm as 0024 for a profile center distance of 92 mm as 6031 for a profile center distance of 72 mm possibility of through fixing of conventional door furniture such as roses, escutcheons or short backplate sets enclosed lock case various forend versions in regards to form and optics malleable cast iron latch, deadbolt made of steel 2-turn 20 mm deadbolt throw Lock 6206 Application: Entrance house and apartment doors with increased security according to WK2 Technical features: profile cylinder lock with latch lever function can be supplied in backsets 55, 65, and 80 mm with a 6 mm forend for special burglary prevention for a profile center distance of 72 mm possibility of through fixing of conventional door furniture such as roses, escutcheons or short backplate sets enclosed lock case various forend versions in regards to form and optics malleable cast iron latch, deadbolt made of steel 2-turn 20 mm deadbolt throw with a triple safety tumbler Lock 6043 Application: Radiation protection doors with mechanical safety requirements Technical features: cylinder lock with latch lever function provided for use as profile half cylinders massive follower of malleable cast iron can be supplied in backsets 40 / 80 mm possibility of through fixing of conventional door furniture such as roses, escutcheons or short backplate sets enclosed lock case various forend designs of stainless steel malleable cast iron latch, deadbolt made of steel 1-turn 15 mm deadbolt throw 9
Lock 2154 BUTLER Door open BUTLER function Door closed Door closed Cylinder locked Door handle in free running position 10
Lock 2154 BUTLER Range / Order numbers Lock for profile cylinder Surface format, 20 mm for rebated doors, 24 mm for flush doors DIN LH DIN RH DIN LH DIN RH 55 60 65 80 B 2154 0009 B 2154 0001 B 2154 0025 B 2154 0017 B 2154 0041 B 2154 0033 B 2154 0073 B 2154 0065 B 2154 0010 B 2154 0002 B 2154 0026 B 2154 0018 B 2154 0042 B 2154 0034 B 2154 0074 B 2154 0066 B 2154 0013 B 2154 0005 B 2154 0029 B 2154 0021 B 2154 0045 B 2154 0037 B 2154 0077 B 2154 0069 B 2154 0014 B 2154 0006 B 2154 0030 B 2154 0022 B 2154 0046 B 2154 0038 B 2154 0078 B 2154 0070 Other options (upon request) Width Follower Special versions Possible striking plates 22 mm for rebated door locks, 28 mm for flush doors 70 100 Swiss round cylinder hole B 9000 0195 B 9000 0203 B 9000 0205 B 9000 0196 B 9000 0204 B 9000 0206 Specification text BKS Latchbolt lock 2154 with an automatic locking for apartment entrance doors; measurements according to DIN 18 251; certified according to VDS class B; forend made of stainless steel, ; with latch lever; closed, galvanized lock case; with assembly friendly guide of the cylinder fixing screw; screw holes for door furniture with connecting screws up to M8 (up to 6 mm for roses) around the follower and cylinder holes; with dust- and swarfguarded bushes; 10 mm steel follower with bronze bearing ring; latchbolt with additional blocking in two positions; automatic deadbolt; latchbolt and automatic deadbolt 20 mm projection; automatic locking triggered through in latchbolt integrated lever (no auxiliary latch necessary); behind backset 28 mm; center distance 92 mm, backset mm 11
Lock 2124 BUTLER + 2174 Door open BUTLER function Door closed Door closed Cylinder locked Door handle in free frunning position 2124 2174 Manually lockable deadbolt 12
Lock 2124 BUTLER + 2174 Range / Order numbers Lock 2124 for profile cylinder surface 55 60 65 80 100 format, 18 mm for rebated doors, 20 mm for rebated doors DIN LH DIN RH DIN LH DIN R B 2124 0007 B 2124 0001 B 2124 0019 B 2124 0013 B 2124 0031 B 2124 0025 B 2124 0055 B 2124 0049 B 2124 0067 B 2124 0061 B 2124 0008 B 2124 0002 B 2124 0020 B 2124 0014 B 2124 0032 B 2124 0026 B 2124 0056 B 2124 0050 B 2124 0068 B 2124 0062 B 2124 0009 B 2124 0003 B 2124 0021 B 2124 0015 B 2124 0033 B 2124 0027 B 2124 0057 B 2124 0051 B 2124 0069 B 2124 0063 B 2124 0010 B 2124 0004 B 2124 0022 B 2124 0016 B 2124 0034 B 2124 0028 B 2124 0058 B 2124 0052 B 2124 0070 B 2124 0064, 24 mm for flush doors DIN LH DIN RH B 2124 0011 B 2124 0005 B 2124 0023 B 2124 0017 B 2124 0035 B 2124 0029 B 2124 0059 B 2124 0053 B 2124 0071 B 2124 0065 B 2124 0012 B 2124 0006 B 2124 0024 B 2124 0018 B 2124 0036 B 2124 0030 B 2124 0060 B 2124 0054 B 2124 0072 B 2124 0066 Lock 2174 for profile cylinder Surface 55 60 65 80 100 Form, 18 mm for rebated doors, 20 mm for rebated doors DIN LH DIN RH DIN LH DIN RH B 2174 0007 B 2174 0001 B 2174 0019 B 2174 0013 B 2174 0031 B 2174 0025 B 2174 0055 B 2174 0049 B 2174 0067 B 2174 0061 B 2174 0008 B 2174 0002 B 2174 0020 B 2174 0014 B 2174 0032 B 2174 0026 B 2174 0056 B 2174 0050 B 2174 0068 B 2174 0062 B 2174 0009 B 2174 0003 B 2174 0021 B 2174 0015 B 2174 0033 B 2174 0027 B 2174 0057 B 2174 0051 B 2174 0069 B 2174 0063 B 2174 0010 B 2174 0004 B 2174 0022 B 2174 0016 B 2174 0034 B 2174 0028 B 2174 0058 B 2174 0052 B 2174 0070 B 2174 0064, 24 mm for flush doors DIN LH DIN RH B 2174 0011 B 2174 0005 B 2174 0023 B 2174 0017 B 2174 0035 B 2174 0029 B 2174 0059 B 2174 0053 B 2174 0071 B 2174 0065 B 2174 0012 B 2174 0006 B 2174 0024 B 2174 0018 B 2174 0036 B 2174 0030 B 2174 0060 B 2174 0054 B 2174 0072 B 2174 0066 Other options (upon request) Width Follower Special versions Possible striking plates 70 Swiss round cylinder hole B 9000 0247 B 9000 0433 B 9000 0435 B 9000 0248 B 9000 0434 B 9000 0436 Specification text Deadbolt latch lock 2124 Butler BKS Latchbolt lock 2124 with an automatic locking for apartment entrance doors; measurements according to DIN 18 251; certified according to VDS class B; forend made of stainless steel, ; with latch lever; closed, galvanized lock case; with assembly friendly guide of the cylinder fixing screws; screw holes for door furniture with connecting screws up to M8 (up to 6 mm for roses) around the follower and cylinder holes; with steel protection bushes; 8 mm steel follower with bronze bearing ring; latchbolt with additional blocking in two positions; self-locking automatic latchbolt; latchbolt 20 mm projecting in locking position; automatic locking triggered through integrated lever in latchbolt (no auxiliary latch necessary); behind backset 28 mm; center distance 72 mm; backset mm Deadbolt latch lock 2174 with manually lockable latch BKS Latchbolt lock 2174 with an automatic locking of the latchbolt and manually lockable deadbolt for apartment entrance doors; measurements according to DIN 18 251; certified according to VDS class B; forend made of stainless steel, ; with latch lever; closed, galvanized lock case; with assembly friendly guide of the cylinder fixing screw; screw holes for door furniture with connecting screws up to M8 (up to 6 mm for roses) around the follower and cylinder holes; with swarf-guarded steel bushes; 8 mm steel follower with bronze bearing ring; latchbolt with additional blocking in two positions; manually lockable deadbolt; 20 mm projection of latchbolt and deadbolt, automatic locking triggered through integrated lever in latchbolt (no auxiliary latch necessary); behind backset 28 mm; center distance 72 mm, backset mm 13
Lock 2114 Door open BUTLER function Door closed Door closed Locking cylinder locked Door handle in free running position 14
Lock 2114 Range / Order numbers Lock for profile cylinder Surface Form, 18 mm for rebated doors, 20 mm for rebated doors DIN LH DIN RH DIN LH DIN RH, 24 mm for flush doors DIN LH DIN RH 55 B 2114 0001 B 2114 0002 B 2114 0003 B 2114 0004 B 2114 0005 B 2114 0006 60 65 B 2114 0013 B 2114 0025 B 2114 0014 B 2114 0026 B 2114 0015 B 2114 0027 B 2114 0016 B 2114 0028 B 2114 0017 B 2114 0029 B 2114 0018 B 2114 0030 80 B 2114 0049 B 2114 0050 B 2114 0051 B 2114 0052 B 2114 0053 B 2114 0054 Other options (upon request) Width Follower Special versions Possible striking plates 70 100 Swiss round cylinder hole B 9000 0247 B 9000 0433 B 9000 0435 B 9000 0248 B 9000 0434 B 9000 0436 Specification text BKS Latchbolt lock 2114 with automatic locking of the latch without automatic deadbolt for apartment entrance doors; measurements according to DIN 18 251; certified according to VDS class B; forend made of of stainless steel, ; with latch lever; closed, galvanized lock case; with eassembly friendly guide of the cylinder fixing screw; screw holes for door furniture with connecting screws up to M8 (up to 6 mm for roses) around the follower and cylinder holes; with swarf-guarded steel bushes; 8 mm steel follower with bronze bearing ring; latchbolt with additional blocking in two positions; without automatic deadbolt; 20 mm projecting latchbolt; automatic locking triggered through in latchbolt integrated lever (no auxiliary latch necessary); behind backset 28 mm; center distance 72 mm; backset mm 15
Safety lock 0024 Profile cylinder Round cylinder Short cylinder 16
Safety lock 0024 Range / Order numbers Lock for profile cylinder surface Form, 20 mm for rebated doors, 22 mm for rebated doors DIN LH DIN RH DIN LH DIN RH, 24 mm for rebated doors DIN LH DIN RH 55 00241001 00241002 00240616 00240617 -- -- Steel nickel-silver 60 65 00241003 00240606 00241004 00240594 00240618 00240603 00240619 00240604 -- 00240628-00240629 80 00241007 00241008 00240622 00240623 -- -- Surface Form, 24 mm for flush doors, 28 mm for flush doors DIN LH DIN RH DIN LH DIN RH 55 00241011 00241012 00241021 00241022 Steel nickel-silver 60 65 00241013 00240021 00241014 00240022 00241023 00241031 00241024 00241032 80 00241017 00241018 00241017 00241018 Lock for round cylinder Surface Steel nickel-silver 65 Form 24 x 310 mm for rebated doors 28 x 310 mm for flush doors DIN LH DIN RH DIN LH DIN RH 00240595 00240596 00240597 00240598 Lock for short cylinder Surface Steel nickel-silver 65 Form 24 x 310 mm for rebated doors 28 x 310 mm for flush doors DIN LH DIN RH DIN LH DIN RH 00240599 00240600 00240601 00240602 Other options (upon request) Width 24 mm for rebated door 24 mm for flush door 22 x 310 24 x 310 28 x 310 Follower 70 90 Offset deadbolt (profile cylinder lock only) Special versions Sawing protection; Latch fixing device; Front bevel; Rounded forend Anti-panic function D (only backset 65mm) Anti-panic function E (only backset 65 mm) Possible striking plates S 401 S 407 S 404 Specification text BKS mortise lock 0024 for profile cylinders (or round cylinders / or short cylinders); for apartment entrance doors; nickel silver painted forend (or stainless steel forend), (or ); with latch lever; enclosed, galvanized lock case; screw holes for door furniture with connecting screws up to M 8 around deadbolt and latch follower; 10 mm malleable cast iron follower; latch made of malleable cast iron, nickel plated; 2-turn steel deadbolt, nickel plated; center distance 92 mm; backset mm 17
Safety lock 6031 Profile cylinder Round cylinder Short cylinder 18
Safety lock 6031 Range / Order numbers Lock for profile cylinder Surface Steel nickel-silver 55 60 65 70 80 Form 18 mm for rebated doors 20 mm for rebated doors DIN LH DIN RH DIN LH DIN RH 60310013 60310015 -- -- -- -- -- -- -- -- 60310014 60310016 -- -- -- -- -- -- -- -- 60310063 60310067 60310035 60310021 60310039 60310023 60310053 60310025 60310057 60310061 60310064 60310068 60310036 60310022 60310040 60310024 60310054 60310026 60310058 60310062 24 mm for flush doors DIN LH DIN RH 60310065 60310043 60310037 60311001 60310041 60310027 60310055 60311003 60310059 60311005 60310066 60310044 60310038 60311002 60310042 60310028 60310056 60311004 60310060 60311006 Lock for round cylinder Surface Steel nickel-silver 55 Form 20 mm for rebated doors 24 mm for flush doors DIN LH DIN RH DIN LH DIN RH 60311007 60311008 60311009 60311010 Lock for short cylinder Surface Form 20 mm for rebated doors 24 mm for flush doors DIN LH DIN RH DIN LH DIN RH 55 60311011 60311012 60311017 60311018 Steel nickel-silver 60 60311013 60311014 60311019 60311020 65 60311015 60311016 60311021 60311022 Other options (upon request) Width Follower 9 mm 10 mm Sawing protection Special versions Front bevel No. 3+5 Latch fixing device Possible striking plates S 204 S 241 S 401 S 404 S 407 S 411 Specification text BKS mortise lock 6031 for profile cylinders (or round cylinders / or short cylinders)according to DIN 18 251 class 3; for apartment entrance doors; nickel silver painted forend (or stainless steel forend), (or ); with latch lever; enclosed, galvanized lock case; screw holes for door furniture with connecting screws up to M 8 around deadbolt and latch follower; 8 mm malleable cast iron follower; latch made of malleable cast iron, nickel plated; 2-turn steel deadbolt, nickel plated; center distance 72 mm; backset mm 19
Safety lock 6206 20
Safety lock 6206 Range / Order numbers Lock for profile cylinder Surface Form 20 x 280 mm for rebated doors 24 x 280 mm for flush doors DIN LH DIN RH DIN LH DIN RH 55 62061001 62061002 62061007 62061008 Steel nickel-silver 65 62061003 62061004 62061009 62061010 80 62061005 62061006 62061011 62061012 55 62060042 62060043 62061015 62061016 65 62060007 62060008 62061017 62061018 80 62061013 62061014 62061019 62061020 Other options (upon request) Width dimensions 20 x 235 mm dimensions 24 x 235 mm Follower Special versions Possible striking plates S 204 S 241 S 350 (20 x 20) S 500 Specification text BKS mortise lock 6206 for apartment entrance doors according to WK2 (ET1); nickel silver painted 6 mm thick forend (or stainless steel forend), welded 5 times, ; with latch lever; enclosed, galvanized lock case; screwed together 4 times; screw holes for door furniture with connecting screws up to M 8 around deadbolt and latch follower; 8 mm malleable cast iron follower; latch made of malleable cast iron, nickel plated; 2-turn steel deadbolt with triple safety tumbler, nickel plated; center distance 72 mm; backset mm 21
Mortise lock 6043 22
Mortise lock 6043 Range / Order numbers Lock for double profile cylinder Surface Form Version 20 mm for rebated doors DIN LH DIN RH 24 mm for flush doors DIN LH DIN RH 40/80 with latch lever without latch lever B 6043 0215 B 6043 0211 B 6043 0216 B 6043 0212 B 6043 0207 B 6043 0203 B 6043 0208 B 6043 0204 Other options (upon request) Width Follower Special versions Possible striking plates S 204 S 241 S 350 (20 x 20) S 500 Specification text BKS mortise lock 6043 for radiation protection doors; prepared for profile half cylinder with a 40 mm + 80 mm backset; stainless steel forend, ; with latch lever; enclosed galvanized lock case; screw holes for door furniture with connection holes up to M 8 around latch and deadbolt follower; 8 mm malleable cast iron follower; latch made of malleable cast iron, nickel plated; steel deadbolt, one turn, nickel plated; center distance 72 mm; backset 40 + 80 mm 23
Product features Mortise locks for fire rated doors Locking to the top As option for special designs in combination with the BKS spring bolt lock 1795 possible. Latch Provides a durable closure of the door. Lock case Fully enclosed, it protects as stable galvanized design the function of the lock. As fixing element of the lock with the door. The various design scopes of surfaces and shapes must be specified in the order. Follower Receives the spindle of the door furniture and operates the lock. Fixing hole for door furniture Provides for a solid, through fixing of the door furniture. Deadbolt Secures the closed door against unauthorized entries. Must be specified when ordering. Locking method For profile cylinders with latch lever function. Also for Swiss round cylinders in some versions. 24
Product features Mortise locks for fire rated doors Lock 1125 Application: Fire rated doors (H80) requiring reversible locks Technical features: profile cylinder lock with latch lever function, 72 mm distance available in backset 65 mm usable DIN LH + DIN RH by turning the lock galvanized lock case fully enclosed steel latch additional steel deadbolt, single turn with 14 mm deadbolt projection galvanized steel forend, 24 mm forend width Lock 1206 + 6306 Application: Fire rated doors, also with burglary prevention requirements Technical features: profile cylinder lock with latch lever function, 72 mm distance according to DIN 18250 class 3 (for contract doors) + class 5 (safety lock) can be supplied in backsets 55, 65, 80 and 100 mm possibility of through fixings of conventional door furniture galvanized lock case fully enclosed galvanized steel latch class 3 with zinc-die cast deadbolt class 5 with galvanized steel safety deadbolt reversible latch, usable DIN LH + DIN RH 2-turn 20 mm deadbolt throw various forend versions relative to form and finish as safety lock 6306 with 6 mm forend as triple latch lock 6065 with additional latch Locks 6138 Lock 2327 Application: Fire rated doors, which are combined with various locking suites Technical features: profile cylinder lock for 2 profile cylinders, 72 mm distance with latch lever function according to DIN 18250 class 3 available in backset 32/65 mm galvanized lock case fully enclosed galvanized steel latch galvanized steel deadbolt one turn deadbolt throw various forend versions in regards to form and optics Lock 2338 with locking to the top Application: Custom designed fire rated doors Technical features: profile cylinder lock with latch lever function, 72 mm distance for fire rated doors according to DIN 4102 can be supplied in backsets 65, 80 and 100 mm possibility of through fixing of conventional door furniture galvanized lock case fully enclosed galvanized steel latch galvanized steel deadbolt one turn deadbolt throw various front versions in regards to form and optics in conjunction with BKS spring bolt lock 1795 25
Single latch lock 1125 for fire rated doors 26
Single latch lock 1125 for fire rated doors Range / Order numbers Single latch lock Surface Steel galvanized 65 Form 24 mm usable DIN LH + DIN RH 11250001 Additional possibilities (upon request) Width Follower Special versions Possible striking plates B 9000 0775 Specification text BKS single latch lock 1125; usable DIN LH + DIN RH, suitable for fire rated doors according to DIN EN 1634 + DIN 4102; galvanized forend, ; with latch lever; enclosed galvanized lock case; 2-turn 9 mm steel follower; steel latch, galvanized; additional steel deadbolt, single turn, galvanized; center distance 72 mm; backset 65 mm 27
Lock 1206 according to DIN 18250 for fire rated doors Class 3 Class 5 28
Lock 1206 according to DIN 18250 for fire rated doors Range / Order numbers Lock according to DIN 18250 class 3 for profile cylinders Surface Steel galvanized 55 65 80 100 55 65 80 100 Form 20 mm for rebated doors 24 mm for flush doors DIN LH DIN RH DIN LH DIN RH 12060363 12060365 12060367 12060369 12060379 12060381 12060383 12060385 12060364 12060366 12060368 12060370 12060380 12060382 12060384 12060386 12060371 12060373 12060375 12060377 12060387 12060389 12060391 12060393 12060372 12060374 12060376 12060378 12060388 12060390 12060392 12060394 Lock according to DIN 18250 class 5 for profile cylinders Surface Steel galvanized 55 65 80 100 55 65 80 100 Form 20 mm for rebated doors 24 mm for flush doors DIN LH DIN RH DIN LH DIN RH 12060336 12060324 12060340 12060360 12060344 12060328 12060332 12060354 12060337 12060325 12060341 12060361 12060345 12060329 12060333 12060355 12060338 12060326 12060342 12060100 12060346 12060330 12060334 12060358 12060339 12060327 12060343 12060121 12060347 12060331 12060335 12060359 Other options (upon request) Width Follower Special versions Possible striking plates Gold-plated forend Swiss round cylinder hole Deadbolt and follower monitoring Latch and deadbolt with anti-friction coating B 9000 0319 B 9000 0435 B 9000 0248 B 9000 0320 B 9000 0436 Specification text DIN 18250 class 3 BKS fire rated door lock 1206 according to DIN 18250 class 3 suitable for fire rated doors; galvanized steel forend (or stainless steel), ; galvanized enclosed lock case with assembly friendly guide of the cylinder fixing screw; 2-turn 9 mm steel follower; galvanized latch made of malleable cast iron; 2-turn zinc die-cast deadbolt; center distance 72 mm; with latch lever function; mm backset DIN 18250 class 5 BKS fire rated door lock 1206 according to DIN 18250 class 5 suitable for fire rated doors; galvanized steel forend (or stainless steel), ; galvanized enclosed lock case with assembly friendly guide of the cylinder fixing screw; 2-part 9 mm self-clamping steel follower; galvanized latch made of malleable cast iron; 2-turn zinc die-cast deadbolt; center distance 72 mm; with latch lever function; mm backset 29
Lock 2327 for fire rated doors 30
Lock 2327 for fire rated doors Range / Order numbers Lock for double profile cylinder Surface Form 20 mm for rebated doors 24 mm for flush doors DIN LH DIN RH DIN LH DIN RH 32 / 65 Rounded B 2327 0003 B 2327 0004 B 2327 0007 B 2327 0006 Other options (upon request) Width Follower Special version Possible striking plates Gold plated forend Swiss round cylinder hole Latch and follower monitoring Latch and deadbolt with anti-friction coating B 9000 0319 B 9000 0435 B 9000 0248 B 9000 0320 B 9000 0436 Specification text BKS mortise lock 2327 according to DIN 18250-class 3 suitable for fire rated doors; provided for 2 differently locking profile cylinders of backset 32 / 65 mm, stainless steel forend, ; galvanized enclosed lock case, with assembly friendly guide of the cylinder fixing screw; 9 mm malleable cast-iron follower; one turn galvanized malleable cast-iron latch; center distance 72 mm; with latch lever function; backset 32 / 65 mm 31
Lock 2338 for profile cylinder 32
Lock 2338 for profile cylinder Range / Order numbers Lock for profile cylinder Surface Form 20 mm for rebated doors 24 mm for flush doors DIN LH DIN RH DIN LH DIN RH 65 B 2338 0007 B 2338 0008 B 2338 0001 B 2338 0002 80 B 2338 0009 B 2338 0010 B 2338 0003 B 2338 0004 100 B 2338 0011 B 2338 0012 B 2338 0005 B 2338 0006 Other options (upon request) Width Follower Special versions Possible striking plates Gold plated forend Swiss round cylinder hole Deadbolt and follower monitoring Latch and deadbolt with anti-friction coating, unsafety latch fixing device B 9000 0319 B 9000 0435 B 9000 0248 B 9000 0320 B 9000 0436 Specification text BKS mortise lock 2338 for fire rated doors suitable according to DIN 4102; with additional locking to the top, provided for the combination with spring bolt lock 1795, in combination with tube 9037 with locking spring; stainless steel forend, ; galvanized enclosed lock case, with assembly friendly guide of the cylinder fixing screw; 9 mm malleable cast-iron follower; galvanized malleable cast-iron latch; 1-turn galvanized steel deadbolt; center distance 72 mm; mm backset 33
Spring bolt lock 1795 for lock 2338 with locking to the top 1795 9037 34
Spring bolt lock 1795 for lock 2338 with locking to the top Range / Order numbers Spring bolt lock 1795 Surface Form 20 x 54 mm for rebated doors usable DIN LH + DIN RH 24 x 54 mm for flush doors usable DIN LH + DIN RH -- B 1795 0007 B 1795 0005 Tube 9037 with locking spring Door height up to 2250 mm 2251 mm 2500 mm 2501 mm 2750 mm 2751 mm 3000 mm Rod length 1135 mm 1385 mm 1635 mm 1885 mm Item B 9037 0001 B 9037 0002 B 9037 0003 B 9037 0004 Other options (upon request) Width Follower Special versions Possible striking plates B 9000 0567 (for 1795) Specification text Spring bolt lock BKS spring bolt lock 1795 for fire rated doors according to DIN 4102, provided for the use with BKS mortise lock 2338, with additional locking to the top; in combination with tube 9037 with locking spring; stainless steel forend, ; galvanized guiding tube Tube Tube 9037 with locking spring for fire rated doors suitable according to DIN 4102; provided for the use with BKS mortise lock 2338, with additional locking to the top; in combination with BKS spring bolt lock 1795; galvanized tube; mm door height 35
Triple latch lock 6065 for fire rated doors 36
Triple latch lock 6065 for fire rated doors Range / Order numbers Triple latch lock for profile cylinders Surface Form 20 mm for rebated doors 24 mm for flush doors DIN LH DIN RH DIN LH DIN RH 65 B 6065 0203 B 6065 0204 B 6065 0161 B 6065 0162 80 B 6065 0209 B 6065 0210 B 6065 0211 B 6065 0212 100 B 6065 0207 B 6065 0208 B 6065 0169 B 6065 0170 Other options (upon request) Width Follower Special versions Possible striking plates Latch, deadbolt and follower monitoring Unsafety latch fixing device B 9000 0319 B 9000 0435 B 9000 0248 B 9000 0320 B 9000 0436 Specification text BKS mortise tripe latch lock 6065 for fire rated doors suitable according to DIN 4102; provided for use with the additional latch locks 6138 and connecting tube 9013; stainless steel forend, ; galvanized enclosed lock case with assembly friendly guide of the cylinder fixing screw; 9 mm malleable castiron follower; galvanized malleable cast-iron latch; 1-turn galvanized steel deadbolt; center distance 72 mm; mm backset 37
Additional latch lock 6138 for triple latch lock 6065 6138 9013 38
Additional latch lock 6138 for triple latch lock 6065 Versions / Order numbers Additional latch lock 6138 Surface Front Form 20 mm for rebated doors 24 mm for flush doors DIN LH DIN RH DIN LH DIN RH 65 B 6138 0145 B 6138 0146 B 6138 0109 B 6138 0110 80 B 6138 0147 B 6138 0148 B 6138 0125 B 6138 0126 100 B 6138 0149 B 6138 0150 B 6138 0117 B 6138 0118 Connecting tube 9013 Door height 1972 mm 2222 mm 2472 mm Length of tube (B) 713 mm 963 mm 1213 mm Item B 9013 0031 B 9013 0032 B 9013 0033 Other options (upon request) Width Follower Special versions Possible striking plates B 9000 0459 B 9000 0523 Specifictation text Additional latch lock BKS additional latch lock 6138 for fire rated doors suitable according to DIN 4102; provided for use with the triple latch lock 6065 and connecting tube 9013; stainless steel forend, ; galvanized enclosed lock case; galvanized malleable cast-iron latch; mm backset Connecting tube BKS connecting tube 9013 for fire rated doors suitable according to DIN 4102; for use with triple latch lock 6065 and additional latch locks 6138; galvanized steel; mm door height 39
Safety lock 6306 for fire rated doors 40
Safety lock 6306 for fire rated doors Range / Order numbers Lock for profile cylinder Surface Form 20 x 280 mm for rebated doors 24 x 280 mm for flush doors DIN LH DIN RH DIN LH DIN RH 55 63060035 63060036 63060043 63060044 65 80 63060037 63060039 63060038 63060040 63060045 63060047 63060046 63060048 100 63060041 63060042 63060049 63060050 Other options (upon request) Appearance Width Follower Special designs Possible striking plates Gold plated forend dimensions 20 x 235 mm dimensions 24 x 235 mm Swiss round cylinder hole Deadbolt and follower monitoring Latch and deadbolt with anti-friction coating B 9000 0319 B 9000 0435 B 9000 0248 B 9000 0320 B 9000 0436 Specification text BKS safety lock 6306 for fire rated doors suitable according to DIN 18250 class 5; with a 6 mm thick stainless steel forend, ; galvanized enclosed lock case, with assembly friendly guide of the cylinder fixing screw; 2 part steel follower, self-clamping, 9 mm; galvanized malleable cast-iron latch; 2-turn galvanized steel deadbolt with a triple safety tumbler; center distance 72 mm; with latch lever function; mm backset 41
Product features Mortise locks for internal doors of class 1 4 Latch Holds the door in closed position. Lock case fully enclosed, it protects the function of the lock. Follower Receives the spindle of the door furniture operates the lock. As fixing element of the lock with the door. The various design scopes on surfaces and shapes must be specified in the order. Fixing hole for door furniture Produces a solid and continuous through fixing of the door furniture. In case of class 4 with swarfguarded steel bushes. Deadbolt Secures a closed door against unauthorized entry. Sound dampening Provides the necessary silence when closing the door in case of contract mortise locks and heavy duty mortise locks. Must be specified in orders. Locking method Depending on the use as bath room, warded key or cylinder lock. 42
Product features The BKS locks in class 1 4 according to DIN 18 251 Class 1 Application: Light interior doors, such as in private living areas Technical features: warded or bath room lock without latch lever function warded key in various curves bathroom lock with additional bath follower for a combination with suitable door furniture for bathroom doors available as 55 mm backset possibility for through fixing of conventional door furniture such as roses, escutcheons or short backplate sets key block to stop the warded key revised enclosed lock case to automatically supply doors in standard production various forends versions in regards to form and optics Class 2 Application: Light internal doors, such as in private living areas Technical features: cylinder lock with latch lever function prepared for use of profile cylinders according to DIN 18 252 available as 55 mm backset possibility of through fixing of conventional door furtniture such as roses, escutcheons or short backplate sets enclosed lock case various forend versions in regards to form and optics 2-turn 20 mm deadbolt throw Class 3 Application: Contract doors and entrance apartment doors with frequent visitors in administrative and industrial buildings Technical features: cylinder lock with latch lever function provided for use of profile cylinders according to DIN 18 252 bathroom lock with additional bath follower for a combination with suitable door furniture for bathroom doors clamping follower with stronger anti-friction bearing to eliminate free play in the operation of the lock by the door furniture can be supplied in backsets 55, 60, 65, 70, 80 and 90 mm possibilty of through fixing of conventional door furniture such as roses, escutcheons or short backplated sets enclosed lock case various forend versions in regards to form and optics 2-turn 20 mm deadbolt throw Class 4 Application: Heavy contract doors with a great amount of visitors in administrative and industrial buildings (such as government offices), which also have to provide increased demands in regards to burglary prevention Technical features: cylinder lock with latch lever function provided for use of profile cylinders according to DIN 18 252 bathroom lock with additional bath follower for a combination with suitable door furniture for bathroom doors clamping follower with stronger anti-friction bearing to eliminate free play in the operation of the lock by the door fitting can be supplied in backset 55, 60, 65, 70, 80, 90 and 100 mm possibility of through fixing of conventional door furniture such as roses, escutcheons or short backplate sets enclosed lock case with anti-drill hardened swarf-guarded steel bushes various forend versions in regards to form and optics 2-turn 20 mm deadbolt throw 43
Lock 0215 class 1 Warded lock Bathroom lock 44
Lock 0215 class 1 Range / Order numbers Warded lock Surface Steel nickel-silver 55 55 Form 18 mm for rebated doors 20 mm for rebated doors DIN LH DIN RH DIN LH DIN RH 02150293 02150180 02150295 02150285 02150294 02150109 02150296 02150286 02150297 02150087 02150299 02150105 02150298 02150106 02150300 02150088 24 mm for flush doors DIN LH DIN RH 02150207 02150170 02150302 02150287 02150301 02150171 02150303 02150288 Bathroom lock Surface Steel nickel-silver 55 55 Form 18 mm for rebated doors 20 mm for rebated doors DIN LH DIN RH DIN LH DIN RH 02150305 02150307 02150309 02150289 02150306 02150308 02150310 02150290 02150311 02150049 02150313 02150067 02150312 02150050 02150314 02150068 24 mm for flush doors DIN LH DIN RH 02150315 02150172 02150317 02150291 02150316 02150173 02150318 02150292 Other options (upon request) Width Follower Special version Possible striking plates Brass, satin finish Brass, polished Brass, hammer painted Coloured painted 20 mm for flush doors 9 mm Zinc die-cast latch + deadbolt S 401 S 404 S 411 2808 2809 2828 Specification text Warded lock BKS internal mortise door lock 0215 in warded version according to DIN 18 251 class 1; nickel silver painted forend (or stainless steel), (or ); enclosed case with tapered form for an automatic access to the lock; plastic latch and deadbolt (or zinc die-cast for stainless steel front), plastic follower with 8 mm, for warded key with 72 mm center distance, with key block to stop the key, with warded key; 55 mm backset Bathroom lock BKS bathroom mortise lock 0215 according to DIN 18251 class 1 Nickel silver painted forend (or stainless steel) with (or ) form, enclosed tapered case for an automatic lock access, 55 mm backset, bathroom lock with a 78 mm distance, plastic latch and deadlock (or zinc die-cast for stainless steel forend), plastic follower with 8 mm, 8 mm zinc die-cast bathroom follower 45
Lock 0415 class 2 46
Lock 0415 class 2 Range / Order numbers Lock for profile cylinder Surface Steel nickel-silver 55 55 Form 18 mm for rebated doors 20 mm for rebated doors DIN LH DIN RH DIN LH DIN RH 04150034 04150031 04150077 04150067 04150035 04150032 04150078 04150068 04150005 04150009 041500079 041500019 04150006 04150010 04150080 04150020 24 mm for flush doors DIN LH DIN RH 04150007 04150017 04150081 04150041 04150008 04150018 04150082 04150042 Other options (upon request) Width Follower Special versions Possible striking plates Brass, satin finish Brass, polished Brass, hammer painted Coloured painted 9 mm Latch + deadbolt made of zinc die-cast S 401 S 404 S 411 2808 2809 2828 Specification text BKS internal mortise lock 0415 for profile cylinders according to DIN 18 251 class 2; nickel silver painted forend (or stainless steel), (or ); enclosed case; plastic follower with 8 mm ; 72 mm center distance; with latch lever function; zinc die-cast latch and deadbolt; 55 mm backset 47
Lock 0515 class 3 Cylinder lock Bathroom lock 48
Lock 0515 class 3 Range / Order numbers Lock for profile cylinder Surface Steel nickel-silver 55 60 65 80 55 60 65 80 Form 18 mm for rebated doors 20 mm for rebated doors DIN LH DIN RH DIN LH DIN RH 05150101 05150103 05150105 05150107 05150109 05150111 05150113 05150115 05150125 05150127 05150129 05150131 05150133 05150135 05150137 05150139 05150102 05150104 05150106 05150108 05150110 05150112 05150114 05150116 05150126 05150128 05150130 05150132 05150134 05150136 05150138 05150140 05150067 05150001 05150117 05150049 05150075 05150009 05150119 05150033 05150085 05150017 05150141 05150057 05150093 05150025 05150143 05150041 05150068 05150002 05150118 05150050 05150076 05150010 05150120 05150034 05150086 05150018 05150142 05150058 05150094 05150026 05150144 05150042 24 mm for flush doors DIN LH DIN RH 05150069 05150003 05150121 05150051 05150079 05150011 05150123 05150035 05150087 05150019 05150145 05150059 05150095 05150027 05150147 05150043 05150070 05150004 05150122 05150052 05150080 05150012 05150124 05150036 05150088 05150020 05150146 05150060 05150096 05150028 05150148 05150044 Bathroom lock Surface Steel nickel-silver 55 60 65 80 55 60 65 80 Form 18 mm for rebated doors 20 mm for rebated doors DIN LH DIN RH DIN LH DIN RH 05150149 05150151 05150153 05150155 05150157 05150159 05150161 05150163 05150173 05150175 05150177 05150179 05150181 05150183 05150185 05150187 05150150 05150152 05150154 05150156 05150158 05150160 05150162 05150164 05150174 05150176 05150178 05150180 05150182 05150184 05150186 05150188 05150077 05150005 05150165 05150053 05150081 05150013 05150167 05150037 05150089 05150021 05150189 05150061 05150097 05150029 05150191 05150045 05150078 05150006 05150166 05150054 05150082 05150014 05150168 05150038 05150090 05150022 05150190 05150062 05150098 05150030 05150192 05150046 24 mm for flush doors DIN LH DIN RH 05150071 05150007 05150169 05150055 05150083 05150015 05150171 05150039 05150091 05150023 05150193 05150063 05150099 05150031 05150195 05150047 05150072 05150008 05150170 05150056 05150084 05150016 05150172 05150040 05150092 05150024 05150194 05150064 05150100 05150032 05150196 05150048 Other options (upon request) Width Follower Special versions Possible striking plates Brass, satin finish Brass, polished Brass, hammer painted Coloured painted 20 mm high. deadbolt 22 x 260 mm 26 x 260 mm 9 mm clamping follower 70 90 Latch lock Deadbolt lock Plastic deadlock (only 55 mm backset) Offset deadbolt Crank latchbolt Latch fixing device Warded insert S 401 S 404 S 407 S 411 2808 2809 2828 Specification text Cylinder lock BKS mortise contract lock 0515 for profile cylinders according to DIN 18251 class 3; nickel silver painted forend (or stainless steel); (or ); galvanized enclosed locked lock case with assembly friendly guide of the cylinder fixing screw; zinc die-cast latch and deadbolt, reinforced steel antifriction bearing with plastic follower (for stainless steel forend: 2 part steel clamping follower, self-clamping) with 8 mm (or 9 mm), with sound damping; center distance 72 mm; with latch lever function; mm backset Bathroom lock BKS mortise contract lock 0515 for bathroom doors; nickel silver painted forend (or stainless steel); (or ); galvanized enclosed locked lock case with assembly friendly guide of the cylinder fixing screw; zinc die-cast latch and deadbolt, reinforced steel anti-friction bearing with plastic follower (for stainless steel forend: 2 part steel clamping follower, self-clamping) with 8 mm (or 9 mm) with sound damping; bathroom deadbolt with 78 mm distance, zinc die-cast bathroom follower with 8 mm ; mm backset 49
Lock 0615 class 4 Cylinder lock Bathroom lock 50
Lock 0615 class 4 Range / Order numbers Lock for profile cylinder Surface 55 60 65 80 100 Form 18 mm for rebated doors 20 mm for rebated doors DIN LH DIN RH DIN LH DIN RH 06150097 06150087 06150099 06150089 06150101 06150091 06150103 06150093 06150105 06150095 06150098 06150088 06150100 06150090 06150102 06150092 06150104 06150094 06150106 06150096 06150047 06150001 06150049 06150009 06150051 06150017 06150053 06150025 06150055 06150039 06150048 06150002 06150050 06150010 06150052 06150018 06150054 06150026 06150056 06150040 24 mm for flush doors DIN LH DIN RH 06150057 06150003 06150059 06150011 06150061 06150019 06150063 06150027 06150065 06150041 06150058 06150004 06150060 06150012 06150062 06150020 06150064 06150028 06150066 06150042 Bathroom lock Surface 55 60 65 80 100 Form 18 mm for rebated doors 20 mm for rebated doors DIN LH DIN RH DIN LH DIN RH 06150117 06150107 06150119 06150109 06150121 06150111 06150123 06150113 06150125 06150115 06150118 06150108 06150120 06150110 06150122 06150112 06150124 06150114 06150126 06150116 06150067 06150005 06150069 06150013 06150071 06150021 06150073 06150029 06150075 06150043 06150068 06150006 06150070 06150014 06150072 06150022 06150074 06150030 06150076 06150044 24 mm for flush doors DIN LH DIN RH 06150077 06150007 06150079 06150015 06150081 06150023 06150083 06150031 06150085 06150045 06150078 06150008 06150080 06150016 06150082 06150024 06150084 06150032 06150086 06150046 Other options (upon request) Width Follower Special versions Possible striking plates Brass, satin Brass, polished 22 x 260 mm 26 x 260 mm 9 mm clamping follower 10 mm (only for wetroom execution) 70 90 Latch lock Deadbolt lock Plastic deadlock (only 55 mm backset) Latch + deadbolt with anti-friction coating Front bevel 3mm Crank latchbolt Latch fixing device Warded insert Wetroom execution offset Deadbolt S 350 S 500 S 204 S 241 Specification text Cylinder lock BKS heavy duty contract mortise lock 0615 for profile cylinder according to DIN 18251 class 4; stainless steel forend; (or ); galvanized enclosed lock case with assembly friendly guide of the cylinder fixing screw; malleable cast iron latch with maintenance-free guide slide bearing and sound damping (graphite or oil hole not required in the forend); steel deadbolt with tumbler, 2 part steel clamping follower, self-clamping with 8 mm (or 9 mm), reinforced steel friction bearing; with anti-drill hardened swarf-guarded steel bushes; 72 mm center distance; with latch lever function; mm backset Bathroom lock BKS heavy duty contract mortise lock 0615 for bathroom doors; stainless steel forend; (or ); galvanized enclosed lock case with assembly friendly guide of the cylinder fixing screw; malleable cast iron latch with maintenance-free guide slide bearing and sound damping (graphite or oil hole not required in the forend); steel deadbolt; 2 part steel clamping follower, self-clamping with 8 mm (or 9 mm), reinforced steel friction bearing; with anti-drill hardened swarf-guarded steel bushes; bathroom locking with a distance of 78 mm, bathroom follower of zinc die-cast with an 8 mm ; mm backset 51
Product features Sliding door locks for internal doors Lock case As stable galvanized design, it protects the function of the lock with a small behind backset. Pivot hook bolt provides a secure closure of the door. Follower Receives the spindle of the door furniture and operates the lock. Guiding pin Finds the correct position when closing the door. Locking method For profile cylinders. As fixing element of the lock with the door. The various special versions for surfaces and forms must be specified when ordering. must be specified when ordering. 52
Product features Special locks for internal doors Roller latch locks 0055 + 1058 Application: Swing doors Technical features: profile cylinder lock roller latch adjustable from the front, adjusting range of 4 12 mm available in backset of 55 mm galvanized lock case fully enclosed brass roller latch zinc die-cast deadbolt, 2 turns with a 20 mm deadbolt projection various forend versions in regards to form and optics also available as swing door latch lock Sliding door locks 0353 + 0393 Application: Sliding doors in the living area Technical features: profile cylinder lock available in backset of 55 mm galvanized lock case fully enclosed with a chrome plated hook bolt spring handle with release button various forend versions in regards to form and optics may also be combined for 2-leaf sliding elements with counter-case G353 available without spring handle, only with hook bolt as 0393 Sliding door lock 0375 Application: Sliding doors in the living area Technical features: profile cylinder lock with latch lever function, 60 mm distance available in backset of 55 mm possibility of through fixing of conventional door furniture galvanized lock case fully enclosed steel hook latch, usable DIN LH and DIN RH Sliding door lock 0381 + 038 HF Application: Sliding doors Technical features: profile cylinder lock with latch lever function, 72 mm distance can be supplied in backsets 55, 65, 70 and 80 mm galvanized lock case fully enclosed steel hook latch, usable DIN LH and DIN RH optional with guiding pin as 0381HF to position the door when closing 53
Deabolt lock 0010 54
Deadbolt lock 0010 Range / Order numbers Lock for profile cylinder Surface Steel nickel-silver 55 Form 18 mm for rebated doors usable DIN LH + DIN RH 20 mm for rebated doors usablbe DN LH + DIN RH Front, 24 mm for rebated doors usable DIN LH + DIN RH 00101001 00100110 00100105 Other options (upon request) Width Follower Special versions Possible striking plates 65 80 forend S 412 Specification text BKS mortise deadbolt lock 0010 for profile cylinders; forend nickel silver painted (or stainless steel), (or ); completely galvanized enclosed lock case; 2-turn zinc die-cast deadbolt, 20 mm projecting; mm backset 55
Latch lock 0216 56
Latch lock 0216 Range / Order numbers Latch lock Surface Steel nickel-silver 55 Form 20 mm forend for rebated doors DIN LH DIN RH 02161001 02161002 Other options (upon request) Width Follower Special versions Possible striking plates 24 mm 60 65 forend S 400 S 403 Specification text BKS mortise latch lock 0216; nickel silver painted forend (or stainless steel), (or ); completely galvanized enclosed lock case; plastic follower with 8 mm ; zinc die-cast latch; mm backset 57
Swing door lock 0055 58
Swing door lock 0055 Range / Order numbers Lock for profile cylinder Surface Steel nickel-silver 55 Form DIN LH 20 mm DIN RH 24 mm usable DIN LH + DIN RH 00551001 00551002 00550082 Other options (upon request) Width Follower Special versions Possible striking plates 60 65 S 440 Specification text BKS mortise door lock 0055 for profile cylinders; brass roller latch (for stainless steel forend: Roller latch also nickel plated), adjustable from the front; forend nickel silver painted (or stainless steel), ; completely galvanized lock case; 2-turn zinc die-cast deadbolt, 20 mm projecting; mm backset 59
Swing door latch lock 1058 60
Swing door latch lock 1058 Range / Order numbers Swing door lock Surface Steel nickel-silver Form 24 mm usable DIN LH + DIN RH 10580001 10580002 Other options (upon request) Width Follower Special versions Possible striking plates S 441 Specification text BKS mortise swing door lock 1058; brass roller latch (for stainless steel forend: Roller latch also nickel plated), adjustable from the front; nickel silver painted forend (or stainless steel), ; completely galvanized enclosed lock case 61
Sliding door lock 0353 +G353 Sliding door lock 0353 Counter-case G353 62
Sliding door lock 0353 +G353 Range / Order numbers Sliding door lock 0353 Surface Form 20 mm Steel nickel-silver 55 03531001 03530052 Counter-case G353 for sliding door lock 0353 Surface Form 20 mm Steel nickel-silver 55 G3531001 G3530017 Other options (upon request) Width Follower Special versions Possible striking plates Brass, satin finish 60 65 forend S 413 Specification text Sliding door lock 0353 BKS mortise sliding door lock 0353; spring handle with release button; with hook bolt, chrome plated; nickel silver painted forend (or stainless steel or brass, satin finish), ; completely galvanized enclosed lock case; mm backset Counter-case G353 BKS mortise counter-lock case G353 for sliding door lock 0353; spring handle with release button; recess for hook bolt; nickel silver painted forend (or stainless steel or brass, satin finish), ; completely galvanized enclosed lock case 63
Sliding door lock 0371 + 0372 Profile cylinder Warded version 64
Sliding door lock 0371 + 0372 Range / Order numbers Sliding door lock 0371 for profile cylinders Surface Form 20 mm Steel nickel-silver 55 03710039 03710040 Sliding door lock 0371 for warded version with solid key Surface Form 20 mm Steel nickel-silver 55 03710123 03710089 Sliding door lock 0372 for warded version with warded key in folding key ring version Surface Form 20 mm Steel nickel-silver 55 03720019 03720006 Other options (upon request) Width Follower Special versions Possible striking plates plates 60 65 forend 0371 in bathroom design S 413 Specification text Sliding door lock 0375 BKS mortise sliding door lock 0371 for profile cylinders (or warded keys); with hook bolt, chrome plated; nickel silver painted forend, (or ); completely galvanized enclosed lock case; (warded version with solid key); mm backset Sliding door lock 0375 BKS mortise sliding door lock 0372 with folding key ring; with curved bolt, chrome plated; nickel silver coated forend, (or ); completely galvanized enclosed case; with warded key in folding key ring version; mm backset 65
Sliding door lock 0375 66
Sliding door lock 0375 Range / Order numbers Lock for profile cylinder Surface Form 20 mm Steel nickel-silver 55 03750014 03750069 Other options (upon request) Width Follower Special versions Possible striking plates 60 65 forend 0375 in bathroom design S 413 Specification text BKS mortise sliding door lock 0375 for profile cylinders; with steel hook latch; nickel silver painted forend (or stainless steel), (or ); completely galvanized enclosed lock case; 2-part zinc die-cast follower with 8 mm ; with latch lever; 55 mm backset 67
Sliding door lock 0381H + 0381HF with guiding pin 0381H 0381HF 68
Sliding door lock 0381H + 0381HF with guiding pin Range / Order numbers Lock 0381H for profile cylinder Surface Form 24 mm usable DIN LH + DIN RH 55 03810007 65 03810008 Galvanized 70 03810017 80 03810010 Lock 0381HF for profile cylinder Surface Form 24 mm usable DIN LH + DIN RH Galvanized 65 03810009 70 03810016 Other options (upon request) Width Follower Special versions Possible striking plates 55 65 80 90 S 448 Specification text Sliding door lock 038H BKS mortise sliding door lock 0381 for steel doors; with steel hook latch, galvanized; galvanized forend (or stainless steel), ; completely galvanized enclosed lock case; measurements according to DIN 18 251; zinc die-cast steel sash follower half shells, 9 mm ; with latch lever; provided for profile cylinders, 72 mm center distance; mm backset Sliding door lock 0381HF with guiding pin BKS mortise sliding door lock 0381HF for steel doors; with steel hook latch, galvanized; with guiding pin; galvanized forend (or stainless steel), ; completely galvanized enclosed lock case; measurements according to DIN 18 251; zinc die-cast steel sash follower half shells, 9 mm ; with latch lever; provided for profile cylinders, 72 mm center distance; mm backset 69
Sliding door lock with spring-loaded handle 0393 70
Sliding door lock with spring-loaded handle 0393 Range / Order numbers Lock Surface Form 20 mm usable DIN LH + DIN RH Steel nickel-silver 03930023 03930017 Other options (upon request) Front Width Follower Special versions Possible striking plates Brass, satin finish Specification text BKS mortise sliding door lock 0393; spring-loaded handle with release button; nickel silver painted forend (or stainless steel or brass, satin finish), ; completely galvanized enclosed lock case 71
Product advice Door handling Inside Inside Inside Inside Outside Outside Outside Outside Left outside DIN left Lever showing to the left Left inside = DIN right Lever showing to the left Right inside = DIN left Lever showing to the right Right outside = DIN right Lever showing to the right Front bevels 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 45 Locks with a sloping forend are required if the leading edge of the door is bevelled. The forend slope is expressed according to a door thickness of 45 mm and is specified by the number of mm the slope deviates from a right angle. Since doors currently may have various door thicknesses, it is recommended that the angle is measured with a purpose made protractor and given on the order. The standard bevel in locks for internal doors is 3 mm, and 5 mm in locks for entrance doors. Attention! Inward opening beveled locks actually receive a shorter backset and outward opening beveled locks have a larger backset. Latch fixing device In order to disable the latch of a mortise lock during daily operation, a latch fixing device may be installed in locks of class 3 + 4 upon request. A mortise lock with a withdrawn and fixed latch enables an unchecked door access. After releasing the fixing device, the latch may then again be operated via the latch lever by using the lever. Note: The specification text must be added accordingly...with latch fixing device. 72
Product advice Crank latchbolt + special anti-friction coating The crank latchbolt is a two-part latch whose middle part hits the strike plate or the steel door frame. This part pushes the latch into the lock forend by a lever actionn. Thus the closing of the door is damped and quietened. As an alternative, we also offer a special anti-friction coating for the standard latch, which also provides noise reduction. The special BKS anti-friction coating has characteristics that no other coating method has: Chemical resistance Low friction coefficient Water and oil repellent Heat and cold resistant The low friction coefficient is of great significance for an easy and therefore quiet closure of doors, especially also for doors with gasket. Swiss round cylinder Locks which are intended for Swiss round cylinders (such as KABA, KESO) require the following attention: The distance from the middle of the follower is 2 mm longer than the comparable dimension of profile cylinders. Example: PZ 72 mm = CH-RZ 74 mm Center PZ Center Swiss Round cylinder Warded insert Description Features Order number Warded insert made of metal Single differ Keyed alike B 9080 0002 B 9080 0003 Key hole profile 0 Key hole profile 1 Key hole profile 2 Key hole profile 3 Key hole profile 6 Key hole profile 7 73
Product features Strike plates for rebated doors Angular strike plates are used in conventional rebated doors in Germany. The angle assures that the latch of the lock does not damage the door frame and lock arbitrarily when closing the door. This is supported by the use of locks with a special anti-friction coating on the latch or on the crank latchbolts. Strike plates for flush doors Lipped strike plates are used in the flush doors common in Europe and Germany. The lip assures that the latch of the lock does not damage the surface of the door frame and close arbitrarily when closing the door. This is supported by the use of locks with a special anti-friction coating on the latch or on the crank latchbolts. Safety strike plates for entrance doors Frames must be stable and connected to the masonry. Strike plates that are extended or anchored in masonry S350 or S500 may impede opening the door in the lock area essentially. A masonry anchor provides increased safety. The possibility also exists to achieve greater safety with strike plate S204 in the area of entrance apartment doors. A stable receiving plate provides a solid connection with the frame. Strike plates for internal doors A wide variety of strike plates is used in conventional internal doors in Germany. So-called U shaped strike plates are frequently used by the door manufacturers. These are identified by an appropriately formed strike plate which is generally created on the same surface as the appropriated mortise locks. The plastic furring provide an attractive appearance of the frames on the frequently open doors. The strike plates are generally assembled from the inside of the frame and resists normal application. 74
Striking plates Strike plate B 9000 for B 2154 BKS lipped strike plate 9000 for automatic locking locks 2154; suitable for normal application, ends Range / Order numbers Order number DIN LH DIN RH B 9000 0195 B 9000 0196 Suitable for locks: B 2154 Strike plate B 9000 for B 2154 BKS angular strike plate 9000 for automatic locking locks 2154; suitable for normal application, () ends 3 16 Range / Order numbers 47 83.5 Order number Rounded 19 Ø 5 Ø 8 DIN LH DIN RH B 9000 0203 B 9000 0204 B 9000 0205 B 9000 0206 90 127.5 98.5 200 164 3 11 9 9 18 19 Suitable for locks: B 2154 24 26 75
Striking plates Strike plate B 9000 for locks 1206/2124/2174/2327/2338/6065/6306 BKS strike plate 9000, straight, for locks 1206/2114/2124/2174/2327/2338/6065/6306; Suitable for normal application; ends Range / Order numbers Order number DIN LH DIN RH B 9000 0319 B 9000 0320 Suitable for locks: 1206 2327 2114 2338 2124 6065 2174 6306 Strike plate B 9000 for 1206/2114/2124/2174/2327/2338/6065/6306 BKS lipped strike plate 9000, for locks 1206/2114/2124/2174/2327/2338/6065/6306; Short design; suitable for normal application; ends Range / Order numbers Order number DIN LH DIN RH B 9000 0435 B 9000 0436 Other options (upon request) Special versions Long design (235 mm) Various lip lengths Square forend Suitable for locks: 1206 2327 2114 2338 2124 6065 2174 6306 76
Striking plates Strike plate B 9000 for 1206/2114/2124/2174/2327/2338/6065/6306 BKS angled strike plate 9000, for locks 1206/2114/2124/2174/2327/2338/6065/6306; usable DIN Left + DIN Right; suitable for normal application Range / Order numbers Order number DIN LH B 9000 0247 B 9000 0248 DIN RH Suitable for locks: 1206 2327 2114 2338 2124 6065 2174 6306 Strike plate B 9000 for spring bolt lock 1795 BKS lipped strike plate 9000, for latch 1795; suitable for normal application; ends Range / Order numbers Order number DIN LH B 9000 0567 DIN RH Suitable for locks: 1795 77
Striking plates Strike plate B 9000 for B 6138 BKS lipped strike plate 9000, for additional latch lock 6138; suitable for normal application; ends Range / Order numbers Order number DIN LH B 9000 0523 DIN RH Suitable for locks: 6138 Strike plate B 9000 for additional latch lock 6138 BKS angled strike plate 9000, for additional latch lock 6138; suitable for normal application; ends Range / Order numbers Order number DIN LH B 9000 0459 DIN RH Suitable for locks: 6138 78
Striking plates Striking plate S204 BKS safety angled striking plate S204 for entrance apartment doors; with furring for a 20 mm deadbolt projection; suitable for heavy application; suitable for DIN LH + DIN RH Range / Order numbers Crank dimension Order number Iron satin nickel-plated 0 S2040008 Other options (upon request) Special versions Brass, polished Brass, satin finish Suitable for locks: 0515 6206 0615 6306 6031 6043 Striking plate S241 BKS safety angled striking plate S241 for entrance apartment doors; with furring for a 20 mm deadbolt projection; suitable for heavy application; suitable for DIN LH + DIN RH Range / Order numbers Crank dimension Order number Iron 0 S2410004 Other options (upon request) Special versions Gold-plated iron Suitable for locks: 0515 6206 0615 6306 6031 6043 79
Striking plates Striking plate S350 BKS safety angled striking plate S350 for apartment entrance doors; 350 mm long; side length of 20 x 20 mm; ends, suitable for heavy application; suitable for DIN LH + DIN RH Range / Order numbers Brass, satin nickel-plated Yellow chromatized Order number S3500005 S3500002 Other options (upon request) Special version Brass, polished Brass, satin finish Suitable for locks: 0615 1206 6043 6206 6306 Strike plate S500 BKS safety angled strike plate S500 for apartment entrance doors; 500 mm long; side length of 20 x 20 mm; ends, suitable for heavy application; suitable for DIN LH + DIN RH Range / Order numbers Brass, satin nickel-plated Yellow chromatized Order number S5000003 S5000002 Other options (upon request) Special versions Brass, polished Brass, satin finish Suitable for locks: 0615 1206 6043 6206 6306 80
Striking plates Striking plate 2808 BKS SECUR striking plate 2808 for internal door locks according to DIN 18251; with plastic furring for single turn locks; with attaching lip; suitable for medium application; suitable for DIN LH + DIN RH Range / Order numbers Steel nickel-silver Order number S2800049 S2800015 Other options (upon request) Brass, polished Brass, satin finish Special versions Furring for 2-turn locks Suitable for locks: 0215 0415 Striking plate 2809 BKS angled striking plate 2809 for internal door locks according to DIN 18251; 20 mm wide + 9 mm thick; with plastic furring for single turn locks; with attaching lip; suitable for medium application; suitable for DIN LH + DIN RH Range / Order numbers Steel nickel-silver Order number S2800048 S2800016 Other options (upon request) Brass, polished Brass, satifn finish Special versions S2800013 S2800014 Suitable for locks: 0215 0415 81
Striking plates Striking plate S400 BKS angled striking plate S400 for BKS latch lock 0216; suitable for light application; ends; suitable for DIN LH + DIN RH Range / Order numbers Steel nickel-silver Order number S4000013 S4000008 Other options (upon request) Special versions Brass, polished Brass, satin finish Suitable for locks: 0216 Striking plate S401 BKS angled striking plate S401 for internal door lock relative to DIN 18251; suitable for light application; ends (10 mm radius); for internal doors and ends for external doors; suitable for DIN LH + DIN RH Range / Order numbers internal doors Steel nickel-silver Order number S4010088 S4010012 Range / Order numbers external doors Steel nickel-silver Order number S4010091 S4010050 Other options (upon request) Special version Brass, polished Brass, satin finish Suitable for locks: 0215, 0515, 6031, 0415, 0024, 0672 82
Striking plates Striking plate S403 BKS lipped strike plate S403 for BKS latch lock 0216; suitable for light application; ends; suitable for DIN LH + DIN RH Range / Order numbers Order number Steel nickel-silver S4030007 S4030001 Suitable for locks: 0216 Striking plate S404 BKS lipped strike plate S404 for internal doors with ends and for external doors with ends according to DIN 18251; suitable for light application Range / Order numbers internal doors Order number Steel nickel-silver DIN LH DIN RH DIN LH DIN RH S4040019 S4040020 S4040015 S4040016 Range / Order numbers entrance doors Order number Steel nickel-silver DIN LH DIN RH DIN LH DIN RH S4040104 S4040105 S4040011 S4040012 Other options (upon request) Special versions Brass, polished Brass, satin finish Suitable for locks: 0215 0515 6031 0415 0024 0672 83
Striking plates Striking plate S407 for offset deadbolts BKS angled striking plate S407 for internal door locks with offset deadbolts; suitable for light application, ends (6 mm radius) Range / Order numbers Order number Steel nickel-silver DIN LH DIN RH DIN LH DIN RH S4070057 S4070058 S4070009 S4070010 Other options (upon request) Special versions Brass, polished Brass, satin finish Suitable for locks: 0515 6031 Striking plate S411 BKS angled striking plate S411 for internal door locks according to DIN 18251; with plastic furring for one turn locks; suitable for light application; suitable for DIN LH + DIN RH Range / Order numbers Steel nickel-silver Order number S4110104 S4110014 Other options (upon request) Brass, polished Brass, satin finish Special versions Furring for 2-turn locks Suitable for locks: 0215 0515 0415 6031 84
Striking plates Striking plate S412 BKS striking plate S412 for BKS latch lock 0010; suitable for light application; ends; suitable for DIN LH + DIN RH Range / Order numbers Steel nickel-silver Order number S4120024 S4120013 Other options (upon request) Special versions forend Suitable for locks: 0010 Striking plate S413 BKS striking plate S413 for BKS sliding door locks 0371/0372/0353/0375; suitable for light application; ends usable DIN LH + DIN RH Range/Order numbers for 0371/0372/0353 Order number Steel nickel-silver S4130023 S4130026 S4130004 S4130008 Range/Order numbers for 0375 Order number Steel nickel-silver S4130039 S4130036 S4130012 S4130016 Suitable for locks: 0371 0353 0372 0375 85
Striking plates Striking plate S440 BKS strike plate S440 for BKS swing door locks 0055; suitable for light application; ends; suitable for DIN LH + DIN RH Range / Order numbers Steel nickel-silver Order number S4400012 S4400004 Suitable for locks: 0055 Striking plate S441 BKS strike plate S441 for BKS swing door locks 1058; suitable for light application; ends; suitable for DIN LH + DIN RH Range / Order numbers Steel nickel-silver Order number S4410011 Other options (upon request) Special versions Suitable for locks: 1058 86
Strking plates Striking plate S448 BKS strike plate S448 for BKS sliding door locks 0381; suitable for medium application wear; ends; suitable for DIN LH + DIN RH Range/Order numbers for 0381H Galvanized Order number S4480003 S4480002 Range/Order numbers for 0381HF Galvanized Order number S4480004 S4480009 Suitable for locks: 0381H 0381HF Striking plate 2828 BKS U shaped strike plate 2828 for internal door locks according to DIN 18251; 28 mm wide + 8 mm thick; with plastic furring for single turn locks; with attaching clamp; suitable for medium application; suitable for DIN LH + DIN RH Versions / Order numbers Steel nickel-silver Order number S2820069 S2820061 Other options (upon request) Brass, satin finish Brass, polished Special versions Furring for 2-turn locks Suitable for locks: 0215 0415 87
Product information for locks The following information regarding locks must be observed in accordance with the manufacturer's liabilities of his products defined in the product liabilities statute. Noncompliance releases us from any liabilities. 1. Product information and use as directed A lock generally has the function to lock and block a door. Simple lock designs serve only to lock the door. This designates that a door is kept closed so that it cannot be opened by pulling or pushing, but may be opened by a simple method, such as by moving the lever. The lock latch generally only called latch serves as lock. Securing the closed door by at least one projecting door latch or by blocking of a deadbolt, which meshes into the appropriate recess of the jamb and or the locking plate, is called blocking. The deadbolt must be blocked against pushing back in its projected position. In addition, the door must be effectively difficult to open without the proper key. The door may only be blocked in a previously closed condition. Cylinder attachment screws must be coordinated or adjusted to the backset length. A mortice lock is a lock which is inserted into a recess in the door leaf (lock pocket) and screwed on. The following must be observed to assure proper use: - Locks, locking plates, door fittings, attaching devices and locking cylinders must be matched. - The current state of technology must be applied for a proper installation, the maintenance and possibly a replacement. This is documented in the standards of these products and in instructions or manufacturer's catalogues. Locks for anti-panic doors or special locks generally do not require an immediate use of keys when activating the door fitting (such as the door lever). Locks for anti-panic doors or special locks may only be combined with locking cylinders with a so-called turning handles (such as knob cylinders) if this is contractually approved by the lock's manufacturer. It is commonly suggested that only the owners of the keys have the right to activate the lock, meaning that the activation of a lock through a knob cylinder (or without a key) is not considered to be as a normal case. Simultaneously pulling back the latch and the prelocked deadbolt only by activating the door lever is a special case and may not replace the normal key rotation to pull back the deadbolt. Locking cylinder may only be unconditionally installed in locks when they are subject to a dimension standard (DIN 18252) and if such locks are clearly prepared for locking cylinders under this standard. In all other cases, the manufacturer, dealer, fabricator or consumer of such locks must obtain the certainty that the locking cylinders he selected are suitable for their intended use. The necessary legal regulations and manufacturer's instructions must be observed. For example, no locking cylinders with a button, knob, or a similar handle may be installed in anti-panic locks. General terms, provided these are not explained in catalogue pages, broschures, price lists or on the internet are explained in the standards relevant for these products (such as DIN 18250, DIN 18251, DIN 18252, DIN 18255, DIN 18257, DIN 18273, DIN EN 179, DIN EN 1125, DIN EN 1303, DIN EN 1906, DIN EN 12209). Deviations from the particular relevant standard must be specified in the order. 2. Incorrect use An incorrect use meaning a product use not as directed of locks, for example, is, when - The flawless use is prevented by inserting foreign objects into the lock or into the locking plate. - When interfering or assaulting the lock or locking plate, which results in a change of the structure, the effectiveness or the function. - The lock bolt is prelocked to keep the door open. - The closing elements are assembled to be blocked in their function or are subsequently treated (for example, painted). - If a load is attached to the lever connection which exceeds the normal force applied by hand. - If unsuitable, such as dimensionally deviating or incorrect keys are being used. - If an expansion or reduction of the required door gap develops when readjusting the hinges or when lowering the door. - If a non-approved double wing door is opened past the inactive wing. - When gripping between the door leaf and the jamb when closing the doors. - when simultaneously activting the lever and the key. 3. Product performance If the product performance is not explicitly defined in our catalogues, broschures, price lists, performance specifications, etc., the requirements must be coordinated with us. The relevant standards serve as guidelines (for example, DIN 18250, DIN 18251, DIN 18252, DIN 18255, DIN 18257, DIN 18273, DIN EN 179, DIN EN 1125, DIN EN 1303, DIN EN 1906, DIN EN 12209). Basic requirements and additional requirements are defined in these standards. The serviceability of locks also depends of the operating frequency, operating method, environmental effects and maintenance. Lock, strike plate, door fittings, locking cylinders and keys must be replaced as soon as problems occur despite proper maintenance. This also applies to attempts to forcefully overcome locks and their accessories (burglary attempts). 4. Product maintenance Locks must be lubricated with suitable lubricants at least once per year more frequently after wear. Door fitting, strike plate and locking cylinder must be checked for their proper condition and their installation. Only cleaning material that do not contain any corrosion-promoting ingredients may be used. 5. Information and instruction duties The following documents and services are available to specialty dealers, locksmiths, architects, planners, fabricators and users upon request, in order to comply with the informational and instructional duties of the product liability statutes: - Catalogues, broschures - Advertising copies, quotation documents, keying plans - The relevant standards serve as guidelines, for example, DIN 18250, DIN 18251, DIN 18252, DIN 18255, DIN 18257, DIN 18273, DIN EN 179, DIN EN 1125, DIN EN 1303, DIN EN 1906, DIN EN 12209 (Exclusive selling rights of the Beuth Verlag GmbH, Berlin 30). - Instructions for installation, operation and maintenance For the selection of locks and the installation, operation and maintenance, - architects and planners should consider to request and observe all required product information from us. - Specialty dealers must consider to observe product information and reference in the price lists and specifically request all necessary instructions from us and to forward these to the fabricators. - Fabricators must consider to observe all product information and specifically request operating and maintenance instructions from us and to forward these to contractors and consumers. 88
Product information for locks 1. The door leaf should not be drilled in the area of the lock installed. General use, installation and maintenance advice for BKS-locks and furniture 2. The spindle should not be knocked through the follower using a hammer. 3. The door leaf should not be carried using the handles. 4. The distance between forend and striker should be between 2 and 5 mm. 5. The latch bolt and dead bolt should not be painted over. 2 to 5 mm 89
Product information for locks 6. The handle should not be operated in the wrong direction. In use a maximum load of 150 N on the handle should not be exceeded. 7. The lock should not be operated with any foreign objects. 8. The dead bolt should not be extended while the door is open. 9. The handle and the key should not be operated simultaneously. 10. Anti-panic locksshould not be left with a key in them. 11. Anti-panic locks should not be fitted with locking cylinders with thumb turn or turn knob. 90
Product information for locks 12. Panic doors should only be used in case of emergency (no frequent use). 13. Double leaf doors should not be forced open using the inactive leaf. 14. As soon as there are visible signs of physical attack (e.g. bent bolts), the lock must be replaced. 15. Locks are to be lubricated at least once a year (non-resinogenic oil). year Exclusion of liability The BKS products are permanently adapted to growing market's requirements and developed further. We also reserve for changes serving the technological progress. This necessity is based on: technical development change and adaptation in product range adaptation to changed laws and technical standards. We have arranged the content of our documents with the greatest possible care. We therefore ask for your understanding that we take no responsibility for possible mistakes with regard to presentation and description of the products. Many thanks for your understanding. 91
Relevant standards The most diverse standards and specifications exist for doors and related products. The most important are listed in the following: DIN 107 Description left and right in the construction industry DIN 1080, part 1 Terms, symbols and units in civil engineering, basics DIN 4102, part 5 + 18 Part 5: Fire performance of building materials and components; fire barriers, barriers in elevator shaft walls and fire-resistant glazing Part 18: Fire performance of building material and components; fire barriers; proof of self-locking properties (continuous operation test) DIN 18 055 Windows; joint impermeability, water penetration resistance and mechanical stress; specifications and tests DIN 18 082, part 1 +3 Part 1: Fire barriers, steel doors T30-1, model A Part 3: Fire barriers, steel doors T30-1, model B DIN 18 095, part 1 +2 Part 1: Doors; smoke protection doors; terms and specifications Part 2: Doors; smoke protection doors; design test of the long-term operational reliability and weathertightness DIN 18 100 Doors; wall openings for doors; Dimensions compliant with DIN 4173 DIN 18 101 Doors, doors for apartment construction; door leaf sizes, hinge seating and lock seating; interrelationship between dimensions DIN 18 111, part 1 Door jambs, steel jambs, standard jambs for rebated doors DIN 18 250 Mortice locks for fire barriers DIN 18 251 Locks; mortice locks for doors DIN 18 252 Locking cylinders for door locks; terms, descriptions DIN 18 255 Building hardware; door handles, doorplates and door rosettes terms, dimensions, specifications DIN 18 257 Building hardware; protective coatings terms, dimensions, specifications, tests and identifications DIN 18 273 Building hardware; door handle sets for fire barriers and smoke protection doors terms, dimensions, specifications and tests DIN 18 357 Official Contracting Terms for the Award of Construction Performance Contracts Part C: General technical contract requirements for construction services (General Pricing Regulations) Fitting operations DIN 18 361 Official Contracting Terms for the Award of Construction Performance Contracts Part C: General technical contract requirements for construction services, glazing operations DIN 68 706 part 1 Interior doors of wood and wood materials, barrier door leaves, terms, prefered dimensions, structural features DIN EN 179 Emergency exit locks with handle or joint plate DIN EN 1125 Anti-panic door locks with horizontal control bar DIN EN 1154 Door closing device with controlled closing process DIN EN 1303 Building hardware locking cylinders for locks specifications and testing procedures DIN V ENV 1627 Windows, doors, fittings burglary prevention specifications and classification DIN V ENV 1628 Windows, doors, fittings burglary prevention testing procedures to calculate the resistance under static stress DIN V ENV 1629 Windows, doors, fittings burglary prevention testing procedures to calculate the resistance under dynamic stress DIN V ENV 1630 Windows, doors, fittings burglary prevention testing procedures to calculate the resistance to counter manual burglary attempts DIN EN 1634 Part 1 + 3 Fire resistance tests for door and connecting devices Part 1: Fire barriers Part 3: Smoke protection barriers DIN EN 1906 Building hardware, door handles, and door knobs specifications and testing procedures 92
Quality A complete Quality Assurance System in correspondence with DIN EN ISO 9001 guarantees consistently high quality of all processes at BKS. This Quality Assurance standard applies the highest demands at the European level and is not relative to production, but also to other business sectors such as research, order processing or customer service. This standard applies to all manufacturing sections at BKS (locking cylinders, door locks, fittings, electronics and door closers). The extensive product range of the G.U-BKS group is designed for heavy-duty use and coordinated. The high performance level in regards to quality, dependability and long life can only be assured when coordinated products are used. The program variety of the G. U-BKS group makes it possible to use this advantage. This is documented by the appropriate tests and registrations, relative to the standards and specifications. These certificates may be requested, if desired. 93
General Terms and Conditions General Sales, Delivery and Payment Terms and Conditions 1. General / Scope of Application 1.1 Our Sales Terms and Conditions are exclusively applicable; we do not recognise contrary terms and conditions by the Purchaser or terms and conditions deviating from our Sales Terms and Conditions unless they have been explicitly approved by us in writing. Our Sales Terms and Conditions shall be applicable even if we carry out delivery to the Purchaser without reservation and with the knowledge of contrary terms and conditions or terms and conditions deviating from our Sales Terms and Conditions. 1.2 All agreements made between us and the Purchaser in view of performance of the present contract have been stipulated in writing in the present contract. 1.3 Our Sales Terms and Conditions are only valid vis-à-vis a contractor within the meaning of 14 BGB [German Civil Code]. 1.4 Our Sales Terms and Conditions shall also be valid for subsequent orders. For current and future business relations the Sales Terms and Conditions shall be valid as framework terms and conditions even if not explicitly agreed upon in future. 1.5 In addition to our General Terms and Conditions our "Installation Guidelines", "Installation Instructions" and Product Informations shall be valid. 2. Offer / Offer Documentation 2.1 Our offer is subject to alterations unless otherwise specified in the order confirmation. After a purchase order has been placed by the customer, a contract is entered into by our written order confirmation. The contents of the contract shall be governed by our written order confirmation. 2.2 Warranty of a quality or acceptance of an independent guarantee on contract conclusion moreover must be explicitly identified in writing accordingly. 2.3 Subsequent modifications of the contract contents must also be made in writing. 2.4 We reserve property rights and copyrights in illustrations, drawings, calculations and other documents; they must not be made available to third parties. This is especially applicable to such written documents identified as being "confidential". Prior to their transmittal to third parties the Purchaser requires our explicit written approval. 3. Prices / Payment Terms and Conditions 3.1 Unless otherwise specified in the order confirmation, our prices are to be understood "ex works" excluding packing and transport charges, insurance and other contingencies; these shall be invoiced separately. 3.2 For pieces or parts which we produce on a special demand or order of the Purchaser we inform the Purchaser about the amount of the production. 3.3 Statutory value-added tax is not included in our prices; it will be shown separately on the invoice on the day of invoicing in the amount stipulated by law. 3.4 Discount deduction requires a special written agreement. Independent of such a written agreement it is stipulated that a discount of 3 % on the net invoice value shall be granted if payment is received within 10 days as from date of invoice. If payment is received within 30 days, we will grant 2 % discount on the net invoice value. No discount will be granted on new invoices as long as still open balances from former invoices exist. Payments will always be used for settlement of the oldest debit item. 3.5 Unless otherwise specified in the order confirmation, the purchase price is due for payment net (without deduction) within 60 days as from date of invoice. If the Purchaser defaults, we shall be entitled to request arrears on interest in the amount of 8 % above the respective basic interest published. But the Purchaser shall be entitled to prove to us that no damage or a damage of a far minor importance has occurred for us as a result of the delay of payment. 3.6 The Purchaser shall only be entitled to setoff rights if his counterclaims have legal force, are undisputed or have been recognised by us. The Purchaser shall be entitled to exercise a general lien in so far as his counterclaim is based upon the same contractual relationship. 3.7 We shall not be obliged to accept bills of exchange or cheques. If cheques or bills of exchange are accepted on a case to case basis upon prior agreement, this will only be made in fulfilment by invoicing the discount charges and collection charges which have to be paid by the customer immediately in cash. Accepted bills and cheques will be finally credited after having been honoured. Acceptance of cheques or bills of exchange will be made without prejudice for later payment obligations. We shall not be responsible for timely presentation, protest and return of the bill of exchange, if it has not been honoured. 3.8 If a bill of exchange or a cheque is not honoured in time or if a payment term granted is exceeded, all debts still open at that time also debts for which a respite has been granted and debts for which bills of exchange or cheques have been given become immediately due for payment. 4. Delivery / Delivery Time 4.1 Prior to start of the delivery time indicated by us all technical questions must have been clarified. If we inform the Purchaser about delivery times these informations are not binding and show only a foreseeable delivery time. 4.2 Observance of our delivery obligation moreover requires timely and orderly fulfilment of the Purchaser's obligations, especially observance of the agreed upon payment terms and conditions. The defence of a non-fulfilled contract remains reserved. 4.3 If the Purchaser has been put on notice to take delivery or if he violates any other duties of co-operation, we shall be entitled to request indemnification of the damage incurred to us to that extent including eventual surplus expenditure. Further claims remain reserved. 4.4 If the prerequisites of item 4.3 exist, the risk of an accidental destruction or an accidental deterioration of the object purchased passes onto the Purchaser at that point in time when the Purchaser has been put on notice to take delivery or is in debtor's delay. 4.5 If non-observance of the delivery time is due to Force Majeure such as for example mobilization, war, riot or similar incidents such as for example strike, lock-out, the delivery time is extended by the duration of the incidents causing the delay in so far as these impediments can be proven to have a major influence on completion or delivery. The same applies if these circumstances occur at sub-suppliers. 4.6 Partial deliveries are admissible within a reasonable extent. 4.7 We shall be liable in general only for delay in delivery in accordance with statutory provisions of the German Commercial Code and the German Civil Code. 4.8 Moreover we shall be liable in accordance with statutory provisions in so far as the delay in delivery is based upon an intentional or grossly negligent contract violation for which we are responsible; we shall also be responsible for a fault caused by our representatives or vicarious agents. 4.9 In so far as the delay in delivery is merely based upon simple fault and no mandatory liability is applicable due to violation of life, body or health, our liability for default damages is limited in such a way that the Purchaser can request each 0.5 percent for each completed week of delay but in total not more than 5 percent of the price for that delivery portion which due to the delay could not be put into useful operation. This is not connected with a modification of the burden of proof to the Purchaser's disadvantage. The Purchaser's legal right to rescind remains unaffected. 4.10 Goods which have been reported to be ready for shipment have to be called by the Purchaser immediately but not later than after a delay of 20 calendar days after having been informed of the readiness for shipment. If no call occurs, we shall be entitled to put the goods on stock and store them upon our own discretion at Purchaser's risk and treat them as delivered ex works. 4.11 If shipment or delivery of the goods is delayed on request or upon instigation of the Purchaser, storage charges may be invoiced starting from one month after notification of readiness for shipment in the amount of 1 % of the invoice value for each month started. The storage charges shall be limited to 5 % of the invoice value unless higher storage charges can be proven by us. 4.12 Fulfilment of our obligation in accordance with the German Packaging Regulations has been transferred by us to a authorized Company who sets up appropriate collecting boxes for packing material which has to be taken back in places where large quantities and small quantities of packing material occurs. Overwraps and sales packages will be taken back by us only via this authorized Company. Outside the scope of application of the Packaging Regulations no packing material will be taken back by us. 5. Participation Duties of our Customers 5.1 Participation services by the customer which are explicitly or tacitly agreed upon within the scope of the contract will be performed without special remuneration unless specified otherwise. 5.2 The customer shall be obliged to inform us on all facts in time from which it results that stock and products in store with us which have been placed at disposal in view of production capacities reported to us cannot be used or cannot be fully used. If residual stock remains, the customer will accept the stock and eventual charges for their destruction in case of premature modification of his disposition. The same applies also to products for which we had to order minimum quantities from our suppliers in so far as we had pointed out this fact to our customer in advance. 5.3 The customer guarantees that the products supplied by him for further processing are suitable for this purpose. We are not obliged to inspect the products supplied by the customer for their property and fitness in view of further processing. Within the scope of current business relations as well as when a processing item has primarily been inspected, tested and released, the customer shall be obliged to inform us of his own accord about each product change. In cases of current processing of items the customer shall be further obliged for each modification of the production conditions in his plant especially when replacing tools, machines or when introducing new production procedures to inspect the item to be processed by us for variations and modifications and to inform us in writing of such variations and modifications. 5.4 We shall not be obliged to check the correctness of instructions given by our customers, material selection or other provisions made by our customer. 5.5 Therefore the customer must check all instructions he is giving as well as the quality of the materials specified or made available to us for compliance with statutory and technical provisions. 5.6 If the customer defaults regarding his duty of procurement or participation after written request, we shall be entitled to statutory rights. 5.7 The taking back of goods requires an explicit written approval, if we are not obligate to take back the goods by law. 6. Passing of Risk 6.1 Unless otherwise specified in the order confirmation, delivery shall be deemed to be agreed upon "ex works". 6.2 The risk for delivery passes onto the customer when leaving our works, at the latest with shipment of the consignment and/or delivery to the carrier or forwarding agent even if partial deliveries are made or if exceptionally we carry out transport at our own expenses or with our transportation means unless otherwise specified. 6.3 If shipment is delayed due to circumstances for which the customer is responsible, the risk passes onto the customer with receipt of the notification of readiness for shipment. 6.4 Return shipments must be returned to us carriage-free. In case of return shipment the risk of loss remains with the customer until the products have been accepted at our works. 6.5 If the customer so requests, we will effect a transport insurance for the shipment; the charges connected with it will be borne by the customer. 94
General terms and conditions 7. Redhibitory Defects We shall be liable for redhibitory defects as follows: 7.1 All such parts or services have to be reworked, newly delivered or rendered again free of charge upon our choice which within the statutory limitation irrespective of the operating period show a redhibitory defect in so far as its cause existed at the time of passing of risk. 7.2 Claims due to redhibitory defects become barred by the statute of limitations in 12 months. The time period starts with the passing of risk (item 6). 7.3 The customer must notify the redhibitory defect to us immediately in writing. 7.4 In case of notification of defects payments by the customer are permitted to be withheld within a scope which is in an adequate ratio to the redhibitory defects occurred. The Purchaser shall only be allowed to withhold payments if a notification of defects has been put forward the justification of which cannot be doubted. If the notification of a defect was wrong, we shall be entitled to request indemnification of expenditures incurred by us from the customer. 7.5 First of all we shall always be granted the possibility of subsequent performance within an adequate delay. 7.6 If subsequent performance fails, the Purchaser may withdraw from contract without prejudice to eventual damage claims or reduce payment. Replacement for fruitless expenditure can only be requested by the Purchaser, if we are responsible for the defect due to intent or gross negligence. 7.7 Claims as a result of defects do not exist in case of only minor variation from the agreed upon quality, in case of only minor impairment of usefulness, in case of natural wear and tear or damages occurring after passing of risk due to wrong or negligent treatment, excessive load, inappropriate consumables or due to special external influences which are not presumed according to contract as well as in case of nonreproducible software errors. If the Purchaser or third parties carry out modifications or repair work in an inappropriate way, no claims as a result of defects exist for it and the resulting consequences either. The same applies in so far as our specifications for handling and other instructions are not observed. 7.8 Claims by the Purchaser for expenditure necessary for the purpose of subsequent performance including but not limited to transport, road, work and material charges are excluded to the extent that the expenditure increases because the object of delivery has subsequently been taken to another place than the establishment of the Purchaser unless this change of location corresponds to its use according to purpose. 7.9 Legal recourse claims by the Purchaser towards us exist only in so far as the Purchaser has not made any agreements with his customer beyond statutory claims due to defects. 7.10 For damage claims item 9 applies. Further or other claims than those stipulated in this item or in item 9 for redhibitory defects are excluded. 8. Industrial Property Rights and Copyrights, Defective Titles Unless otherwise agreed upon, we shall be obliged to render delivery only in the country of the place of delivery free from industrial property rights and copyrights by third parties (hereinafter called property rights). In so far as a third party due to violation of property rights by deliveries rendered by us and used according to contract, puts forward justified claims against the Purchaser, we shall be liable to the Purchaser within the delay determined in item 7.2 as follows: 8.1 Upon our choice and at our own expenses we will either obtain a right of use (usufructuary right) for the deliveries concerned, modify them in such a way that the property right will not be violated or replace them. If this is not possible for us under adequate terms and conditions, the Purchaser shall be entitled to statutory rights of withdrawal or reduction. The Purchaser shall only be allowed to request indemnification for fruitless expenditure, if we are liable for intent or gross negligence. Our obligation to pay damages is governed by item 9. 8.2 The above mentioned obligations exist only in so far as the Purchaser informs us immediately in writing about the claims put forward by the third party, does not recognise a violation and all defences and composition proceedings are reserved for us. If the Purchaser ceases to use the delivery for reasons of damage reduction or for other important reasons, he shall be obliged to inform the third party that no acknowledgement of a violation of property rights is connected with it. 8.3 Claims of the Purchaser are excluded in so far as he is responsible for the violation of property rights. 8.4 Claims of the Purchaser are also excluded in so far as the violation of property rights is caused by particular specifications of the Purchaser, by an application unforeseeable by us or by the fact that the delivery is modified by the Purchaser or used together with products not delivered by us. 8.5 In case of violations of property rights for the claims of the Purchaser stipulated in item 8.1 the provisions of items 7.4, 7.5 and 7.9 apply accordingly. 8.6 Further claims of the Purchaser or other claims of the Purchaser than those stipulated in the present item 8 against us or our vicarious agents for defective title are excluded. 9. Total Liability 9.1 Claims by the Purchaser for indemnification irrespective of the legal nature of the claim put forward are excluded. 9.2 Excluded from this provision are: a) Damages due to violation of substantial contractual obligations. In case of simple negligence, however, liability for indemnification shall be limited to the foreseeable damage typically occurring. b) Damages due to violation of life, body or health if we are responsible for the breach of duty. c) For other damages based upon an intentional or grossly negligent breach of duty with us being equally responsible for a breach of duty by our legal representatives or vicarious agents. d) Indemnification for impossibility or inability. 9.3 No modification of the burden of proof at the Purchaser's disadvantage is connected with the above provision. 9.4 Liability according to the liability for products' law remains unaffected. 9.5 In so far as liability for indemnification towards us is excluded or restricted, this applies also to personal liability for indemnification by our employees, our commercial agents and our vicarious agents. 10. Retention of Title 10.1 The objects of the deliveries (goods under retention of title) remain our property until payment of all debts to which we are entitled from the business relationship. In so far as the value of all securities to which we are entitled towards the Purchaser exceeds the amount of all claims secured by more than 10 %, we will release a corresponding share of the securities on request by the Purchaser. 10.2 During existence of the retention of title the Purchaser shall not be permitted to encumber the goods or pledge them as security and resale is only permitted to resellers in normal dealings and only with a proviso that the reseller receives payment from his customer or makes the reservation that transfer of title will only occur if the customer has met his payment obligations. 10.3 In case of attachments, seizures or other orders or interference by third parties the Purchaser must inform us immediately so that we can institute a claim according to 771 ZPO [German Civil Practice Act]. In so far as the third party is not able to reimburse the court costs and extrajudicial costs of a claim according to 771 ZPO, the Purchaser shall be liable for the loss incurred by us. 10.4 The Purchaser is obliged to take good care of the item purchased; especially he is obliged to insure the item purchased at his own expenses sufficiently at original value against fire, water and theft. In so far as maintenance and inspection work are required, the Purchaser must carry out such work in time at his own expense. 10.5 In case of breaches of duty by the Purchaser including but not limited to delay of payment, we shall be entitled to withdrawal and taking back; the Purchaser is obliged to restitution. Withdrawal and/or exercise of the retention of title does not require rescission by the Supplier; these actions or an attachment of the goods under retention of title by us does not represent a withdrawal from contract unless this has explicitly been declared by us. 10.6 If the Purchaser has resold the purchased item in the ordinary course of business, he assigns, however, to us already now all debts in the amount of the final invoice value (including value-added tax) of our debts accruing for him from resale against his customers or third parties regardless of whether the purchased item has been resold without or after further processing. The Purchaser remains authorised to collect this debt also after assignment. Our authority to collect the debt ourselves remains unaffected. But we undertake not to collect the debt as long as the Purchaser meets his payment obligations from the proceeds taken in, does not default in payment and in particular no petition for opening of insolvency proceedings has been filed or insolvency exists. But if this is the case, we can request that the Purchaser informs us about the debts assigned and their debtors, gives all information necessary for collection, hands out the respective documents and informs the debtors (third parties) of the assignment. 10.7 Processing or reshaping of the purchased item by the Purchaser will always be made on behalf of us. If the purchased matter is processed with other objects not belonging to us, we acquire joint ownership in the new object in the ratio of the value of the purchased item (final invoice value including value-added tax) to the other processed objects at the time of processing. For the object created by processing moreover the same applies as for the purchased item delivered under retention of title. 10.8 If the purchased item is mixed inseparably with other objects not belonging to us, we acquire joint ownership in the new item in the ratio of the value of the purchased item (final invoice value including value-added tax) to the other mixed objects at the time of mixing. If the mixing occurs in such a way that the item of the Purchaser has to be considered the main item, it is deemed to have been agreed upon that the Purchaser transfers pro rata joint ownership to us. The Purchaser holds in custody for us the exclusive ownership or joint ownership thus created. 11. Place of Performance, Venue, Governing Law 11.1 For all rights and duties resulting from our deliveries and services for both parties the registered office of our company shall be considered to be the place of performance. 11.2 In dealings with companies for lawsuits for which the district courts have jurisdiction in rem, the Velbert District Court, and for lawsuits for which county courts have jurisdiction in rem, the Wuppertal County Court shall have general jurisdiction. 11.3 The contractual relationship shall be governed by the law of the Federal Republic of Germany. Application of the UN Convention on Contracts for the International Sale of Goods (CISG) is excluded. 11.4 The data specified by the Purchaser will be stored and processed by electronic data processing to the extent that this is admissible in accordance with the Federal German Law on Data Protection ( 28, 29 BDSG). 11.5 Should any provision of the agreement, the general sales, delivery and payment terms and conditions or other included terms and conditions be or become invalid, in whole or in part, for any reasons whatsoever, or there is a whole, the validity of the remaining provisions shall not be affected thereby. The invalid provision shall be substituted by a valid provision that comes as closely as legally permissible to what the invalid provision was intended to achieve. 95
General business terms...94 + 95 Automatic locking locks...10-15 Heavy duty mortise locks...50 + 51 Warded insert... 73 Triple latch lock...36 + 39 Mortise locks for internal doors...44-51 Latch fixing device... 72 Fire rated door locks...26 + 41 Index...4-7 Crank latchbolt... 73 Standards... 92 Contract mortise locks...48 + 49 Swing door locks...58-61 Product advice...72 + 73 Product information for locks...88-91 Product features mortise locks for fire rated doors...24 + 25 Product features mortise locks for internal doors...42-43 Product features sliding door locks...52 + 53 Product features Striking plates... 74 Product features Safety locks...8 + 9 Quality... 93 Tube 9037...34 + 35 Sliding door locks...62-71 Strike plate B 9000...75 + 78 Strike plate S204... 79 Strike plate S241... 79 Strike plate S350... 80 Strike plate S500... 80 Strike plate S400... 8 Strike plate S401... 82 Strike plate S403... 83 Strike plate S404... 83 Strike plate S407... 84 Strike plate S411... 84 Strike plate S412... 85 Strike plate S413... 85 Strike plate S440... 86 Strike plate S441... 86 Strike plate S448... 87 Strike plate 2808... 81
Strike plate 2809... 81 Strike plate 2828... 87 Lock 0010...54 + 55 Lock 0024...16 + 17 Lock 0055...58 + 59 Lock 0215...44 + 45 Lock 0216...56 + 57 Lock 0353 + G353...62 + 63 Lock 0371...64 + 65 Lock 0372...64 + 65 Lock 0375...66 + 67 Lock 0381H + 0381HF...68 + 69 Lock 0393...70 + 71 Lock 0415...46 + 47 Lock 0515...48 + 49 Lock 0615...50 + 51 Lock 1058...60 + 61 Lock 1125...26 + 27 Lock 1206...28 + 29 Lock 2327...30 + 31 Lock 2338...32 + 33 Lock 6031...18 + 19 Lock 6043...22 + 23 Lock 6065...36 + 37 Lock 6138...38 + 39 Lock 6206...20 + 21 Lock 6306...40 + 41 Lock 2114 automatically locking...14 + 15 Lock 2124 automatically locking...12 + 13 Lock 2154 automatically locking...10 + 11 Lock 2174 manually locking...12 + 13 Shoot bolt lock 1795...34 + 35 Swiss round cylinder... 73 Special locks...54 + 71 Radiation protection lock...20 + 21 Front bevels... 72 Door handling... 72 Connecting rod...38 + 39 Internal door locks...44-47
Gretsch-Unitas GmbH Baubeschläge Johann-Maus-Str. 3 71254 Ditzingen Telephone: +49 (0)7156 301-0 Fax: +49 (0)7156 301-293 www.g-u.de vertrieb-inland@g-u.de BKS GmbH Heidestr. 71 42549 Velbert Telephone: +46 (0)2051 201-0 Fax: +49 (0)2051 201-431 www.bks.de W 0230 0002a 10/2004 my Printed in Germany