! ecor e etworks TM Copyright 2003 Ecore Networks, Ic. All rights reserved. SigalPath 201 (SP201 ) Istallatio Guide Versio C, July 2004 Part Number 15469.1000 SigalPath Software Versio 1100 This Istallatio Guide presets a quick, stadard istallatio of the SP201. Note: The eeds of your etwork may require a istallatio that varies from the stadard istallatio. For a customized istallatio, see the SP201 Customizatio ad Maiteace Guide. For hardware iformatio, see the SP201 Hardware Referece Guide. The SP201 ca support up to four truk circuits. Each truk circuit carries up to 30 chael circuits. Note: A stadard truk circuit (from oe exteral device, through the SP201, to aother exteral device) comprises truk coectios to two ports. The SigalPath cofiguratio software defies each side of the truk circuit (that is, each coectio to a port) as a truk. This documet uses the term truk to idicate a coectio to oe port; it uses the term truk circuit to idicate the complete ed-to-ed coectio (over two ports). Usig these defiitios, a truk circuit comprises two truks. Before you start this istallatio, be sure you have filled out the worksheet for addig this device to your etwork. See the SP201 Site Plaig Worksheet. See the followig sectios for a stadard istallatio of the SP201: Sectio A, Physical Istallatio Sectio B, Clockig Cofiguratio Sectio C, Truk Cofiguratio Sectio D, Chael Cofiguratio Sectio E, SP201 Warmstart Figure 1. SP201 Chassis
2 SP201 Istallatio Guide Note: The cables you coect to the SP201 deped o the protocols. The followig table lists the ports ad lie each protocol uses i this guide s stadard istallatio. Protocol Group Protocol SP201 Ports Lie Chael-Associated DTMF 1 4 T1 Sigalig (CAS) R1 1 4 T1 R2 1 4 E1 N5 1 4 E1 Sigalig System 7 (SS7) ITU C7 1 4 a, 5 8 b E1 ANSI SS7 1 4 c, 5 8 d T1 ISDN ETSI ISDN 5 8 E1 NI2 ISDN 5 8 T1 a. whe the other protocol o the SP201 is ISDN b. whe the other protocol o the SP201 is CAS or ANSI SS7 c. whe the other protocol o the SP201 is ISDN or ITU C7 d. whe the other protocol o the SP201 is CAS A Physical Istallatio 1. Use the four holes o the frot flage of the SP201to mout the chassis i a 19-ich equipmet rack. 2. Coect cables to the ports o the rear of the SP201 chassis, as follows: a For CAS truks (DTMF, R1, R2, or N5), do oe of the followig: For DTMF or R1, coect T1 cables to the RJ48C ports labeled Truk 1 through Truk 4. or For R2 or N5, coect E1 cables to the RJ48C ports labeled Truk 1 through Truk 4. b For SS7 truks, determie whether the SP201 s other protocol is a CAS protocol (DTMF, R1, or R2) or a ISDN protocol (ETSI ISDN or ANSI NI1, NI2, or NI3 ISDN). The do oe of the followig: If the other protocol is a ISDN protocol, the SS7 truks are o ports 1 through 4. Do oe of the followig: - For ANSI SS7, coect T1 cables to the RJ48C ports labeled Truk 1 through Truk 4. or - For ITU C7, coect E1 cables to the RJ48C ports labeled Truk 1 through Truk 4. If the other protocol is a CAS protocol, the SS7 truks are o ports 5 through 8. Do oe of the followig: - For ANSI SS7, coect T1 cables to the RJ48C ports labeled Truk 5 through Truk 8. or - For ITU C7, coect E1 cables to the RJ48C ports labeled Truk 5 through Truk 8.
SP201 Istallatio Guide 3 c For ISDN truks, do oe of the followig: For ETSI ISDN, coect E1 cables to the RJ48C ports labeled Truk 5 through Truk 8. or For NI2 ISDN, coect T1 cables to the RJ48C ports labeled Truk 5 through Truk 8. Note: I a stadard istallatio, chaels o truk 1 of the SP201 map to chaels o truk 5, ad vice versa. I like maer, chaels o truk 2 map to chaels o truk 6 (ad vice versa). Stadard mappig cotiues with truks 3 ad 7 ad with truks 4 ad 8. 3. If you are usig a DC coectio for the SP201, coect the appropriate wires to the power iput o the power supply, as described i the followig substeps: a Coect a earth groud wire to the chassis, as follows: Attach a (miimum) 12 AWG wire to the large earth groud screw, located below the safety groud symbol o the rear of the SP201 chassis. Use a rig termial, such as a AMP (part umber 36160) for this coectio. Note: A earth groud must coect to the SP201 chassis itself so that the chassis remais grouded eve whe the power coectio is removed. b If your SP201 is a DC model, coect a (miimum) 14 AWG three-wire iput cable to the gree three-pi power plug. Make sure you coect the correct wire to each post. With the screwheads facig your left ad with the three progs poitig away from you (as show i Figure 2), ote the followig: The top post is -48 volts DC. The middle post is DC commo. The bottom post (earth groud) is ot used. (A groud wire was coected to the chassis i Step 3a.) Figure 2. Power Coector 4. Coect the SP201 to a power source (a power outlet), ad switch the power o. Note: Shipmets withi North America iclude a power cable for coectio to the power outlet. For shipmets outside North America, cotact your distributor for a cable that meets local requiremets to coect the power supply to a outlet. 5. Coect a DB9 cable from the DB9 serial port of the SP201 to the DB9 COM port of a cotrol termial for example, a PC. 6. O the cotrol termial, start a termial emulatio program, such as HyperTermial. Cofigure the serial commuicatios for the cotrol termial as follows: Baud rate 9600 bps Data bits 8 Parity Noe Stop bit 1 Flow cotrol Noe Whe commuicatio has bee established, you should see the prompt.
4 SP201 Istallatio Guide 7. If you do t see a prompt, press Eter oce. The prompt appears. Note: After you have coected a local termial to the SP201 device, you ca coect a remote termial to the local termial ad maage the device from a remote locatio. See the documet Remote Access to SigalPath Devices. B Clockig Cofiguratio Eter the truk umber [1-8] from which this card is to derive its clock source. Or eter "0" if this card is to use its iteral clock. The PRIMARY clock source is derived from (curret = INTERNALCLOCK): 1 The SECONDARY clock source is derived from (curret = INTERNALCLOCK): 0 The TERTIARY clock source is derived from (curret = INTERNALCLOCK): 0 cofig clocks Clockig (sychroizatio) for the SP201 Clock sourced from the device coected to the remote ed of the R2 truk Backup clock sourced from the SP201 Last-resort clock sourced from the SP201 (Clockig has bee cofigured.) C Truk Cofiguratio Perform the followig procedure oce for each truk (1 8). WARNING: Cofigurig framers will cause LOSS of calls!!!!!!!! Do you wish to proceed ayway (Y/N) : For a T1 lie: LIM type: 2 T1 100 Ohm/2 E1 120 Ohm 1 D4 SF 2 D4 ESF eter T1 frame type (curretly D4 SF): cofig framer p where p is the port umber (1 8) y For T1 lies: 1 or your T1 frame type) Truk o port p
SP201 Istallatio Guide 5 For a E1 lie: LIM type: 2 E1 120 Ohm/2 E1 120 Ohm 1 G704 CRC 2 G704 ocrc 3 G704 MF CRC 4 G704 MF ocrc eter E1 frame type (curretly G704 MF o CRC): For T1 lies: lie codig type choices are: 1 AMI 2 B8ZS eter lie codig type (curretly B8ZS) : For E1 lies: lie codig type choices are: 1 AMI 2 HDB3 eter lie codig type (curretly HDB3) : For T1 lies: lie legth choices are: 1 0 to 115 feet 2 82 to 213 feet 3 180 to 312 feet 4 279 to 410 feet 5 377 to 509 feet 6 476 to 607 feet 7 574 to 689 feet eter lie legth (curretly 0-115 feet): user > For E1 lies: 3 (or your E1 frame type) For T1 lies: 2 (or your T1 lie codig) For E1 lies: 2 (or your E1 lie codig) 1 (or your T1 cable legth) Frame type for truk Lie codig for truk T1 cable legth (The truk has bee cofigured.)
6 SP201 Istallatio Guide D Chael Cofiguratio See the followig sectios to cofigure the protocols i your SP201: DTMF sigalig R1 sigalig R2 sigalig N5 sigalig ANSI SS7 sigalig ITU C7 sigalig ETSI ISDN sigalig NI2 ISDN sigalig Sectio D.1, Chael Cofiguratio for DTMF Sigalig Sectio D.2, Chael Cofiguratio for R1 Sigalig Sectio D.3, Chael Cofiguratio for R2 Sigalig Sectio D.4, Chael Cofiguratio for N5 Sigalig Sectio D.5, Chael Cofiguratio for ITU C7 or ANSI SS7 Sigalig Sectio D.5, Chael Cofiguratio for ITU C7 or ANSI SS7 Sigalig Sectio D.6, Chael Cofiguratio for ETSI ISDN Sectio D.7, Chael Cofiguratio for NI2 ISDN D.1 Chael Cofiguratio for DTMF Sigalig cofig dt all All DTMF chaels Set 1/1 thru 4/31 out-of-service? (y or ) : <curret=> DTMF Caller ID/ANI used? (y or ) : <curret=> Other modificatios? : (y or ) : <curret=> y (or if caller ID is ot required) Placemet of chaels 1 31 of truks 1 4 ito service Request for caller idetificatio Completio of stadard cofiguratio for DTMF sigalig (If you wish to cofigure other parameters for DTMF sigalig, type y. The refer to the SP201 Customizatio ad Maiteace Guide.) (DTMF sigalig has bee cofigured.)
SP201 Istallatio Guide 7 D.2 Chael Cofiguratio for R1 Sigalig cofig r1 all All R1 chaels Set 1/1 thru 4/31 out-of-service? (y or ) : <curret=> Placemet of chaels 1 31 of truks 1 4 ito service Template # for default IAM? : (rage 1-5) : <curret=1> 1 Use of R1 IAM template 1 Template # for default ACM? : (rage 1-5) : <curret=1 1 Use of R1 ACM template 1 Iclude Feature Group D (caller ID/ ANI)? (y or ) : <curret=> (The followig four questios appear oly if you aswered y to the previous questio.) y (or if caller ID is ot required) Request for caller idetificatio Use 911-Operator Services Sigalig (y or ) : <curret=> No use of 911 support Max br of ANI digits to sed R1 (0 = all)? : (rage 0-32) : <curret=0> 0 (zero) Support for ANI of ay size Are Iformatio digits supported? (y or ) : <curret=> No support of Iformatio digits Separate Wik required for B-Party Number? (y or ) : <curret=> No separate wik for B-Party Require wik at ed of selectio? (y or ) : <curret=> Geerate rigback toe for R1 origiated calls? (y or ) : <curret=> No wik required at ed of selectio No rigback geerated for caller (Stadard cofiguratio for R1 sigalig has bee completed. If you wish to cofigure other parameters for R1 sigalig, refer to the SP201 Customizatio ad Maiteace Guide.)
8 SP201 Istallatio Guide D.3 Chael Cofiguratio for R2 Sigalig cofig r2 all All R2 chaels Set 1/1 thru 4/31 out-of-service? (y or ) : <curret=> Select R2 coverter mode : < 1> CCITT <14>Israel < 2> Argetia <15>Korea < 3> Brazil <16>Kuwait < 4> Brazil-Emb <17>Malaysia < 5> Chile <18>Mexico < 6> Chia <19>New Zealad < 7> Columbia <20>Paraguay < 8> Columbia-Bts <21>Philippies < 9> Columbia-Ngt <22>Sigapore <10> Costa Rica <23>Thailad <11> Ecuador <24>Uruguay <12> Greece <25>Veezuela <13> Idoesia Outgoig R2 coverter mode? (1-25; curret=ccitt) : Request R2 caller ID? (y or ) : <curret=> Sed I15 to R2 side at ed of address (vs timeout)? (y or ) : <curret=y> Other modificatios? : (y or ) : <curret=> 1 (or your coutry code) y (or if caller ID is ot required) y (or, depedig o your requiremet) Placemet of chaels 1 31 of truks 1 4 ito service The coutry code for the versio of R2 sigalig this SP201 will use Request for caller idetificatio Sedig a Address Complete code (A aswer of causes the adjacet switch to wait for the appropriate timer to expire before processig the call.) Completio of stadard cofiguratio for R2 sigalig (If you wish to cofigure other parameters for R2 sigalig, type y. The refer to the SP201 Customizatio ad Maiteace Guide.) (R2 sigalig has bee cofigured.)
SP201 Istallatio Guide 9 D.4 Chael Cofiguratio for N5 Sigalig cofig 5 all All N5 chaels Set 1/1 thru 4/31 out-of-service? (y or ) : <curret=> Destiatio coutry code for calls to N5 (curret) : Eter up to 3 digits: (your coutry code) Placemet of chaels 1 31 of truks 1 4 ito service Your coutry s iteratioal dialig code Trasit calls to N5 eabled? (y or ) : <curret=> Disallowace of trasit traffic Use Callig Party Category to set N5 laguage digit? (y or ) : <curret=> N5 side outgoig laguage digit (curret) : Eter up to 1 digits: Prefix to be stripped from digits before sedig to N5 (curret) : Eter up to 3 digits: Digits that cause C11 to be set to N5 (curret) : Eter up to 18 digits: Digits that cause C12 to be set to N5 (curret) : Eter up to 18 digits: Laguage digit expected from N5 [* = ay] (curret) : Eter up to 1 digits: Trasit calls FROM N5 eabled? (y or ) : <curret=> Digits to preped i o-trasit calls comig from N5 (curret) : Eter up to 3 digits: Use callig party category from template? (y or ) : <curret=> Digits to sed whe C11 is received from N5 (curret) : Eter up to 18 digits: Digits to sed whe C12 is received from N5 (curret) : Eter up to 18 digits: Template # for default IAM? : (rage 1-5) : <curret=1> 1 (Press Eter to leave (Press Eter to leave (Press Eter to leave (Press Eter to leave (Press Eter to leave (Press Eter to leave (Press Eter to leave (Press Eter to leave No use of the callig party category to derive the laguage digit The fixed laguage digit for calls origiatig from the N5 side Digits to remove from the frot of the coutry code Digit strig that causes the C11 operator code to be set to N5 Digit strig that causes the C12 operator code to be set to N5 Acceptace of calls oly with a specific laguage digit (if etered) Rejectio of trasit calls (by returig a busy flash) Digits to preped to otrasit calls Derivatio of the Callig Party Category from the N5 laguage digit The digit strig to sed whe the C11 operator code is received from N5 The digit strig to sed whe the C12 operator code is received from N5 Default values for IAM parameters required o the SS7 side but ot specified by the N5 protocol
10 SP201 Istallatio Guide Template # for default ACM? : (rage 1-5) : <curret=1> 1 Use user-defied caller ID (ANI) i calls from N5? (y or ) : <curret=> Geerate rigback toe for N5 origiated calls? (y or ) : <curret=> Default values for ACM parameters required o the SS7 side but ot specified by the N5 protocol No support of caller ID (ANI). Note: Although N5 does ot use ANI, some etworks require ANI i all calls. Aswerig y here places a fixed ANI i each call origiatig from N5. No rigback geeratio by SigalPath for calls from N5 device (This completes stadard cofiguratio of N5 sigalig. If you wish to customize the cofiguratio of N5 sigalig, refer to the SP201 Customizatio ad Maiteace Guide.)
SP201 Istallatio Guide 11 D.5 Chael Cofiguratio for ITU C7 or ANSI SS7 Sigalig cofig lik 5 The truk that supports the SS7 lik Protocol for truk 5 is Q767 This truk is curretly assiged to the Q767 SS7 protocol (The followig message displays oly if truk 5 was ot already the SS7 lik.) Assig the Q767 SS7 to this truk? (y or ; curret="") : y Truk 5 as the SS7 lik Which timeslot (1-31; curret=16)? : For E1 lies: 16 For T1 lies: 24 The chael that will carry sigalig Eter a prox CIC to map UNMAPPED CICs to (0-16383; curret=65535) : (where prox represets the other protocol i this sigalig-coversio set) Origiatig Poit Code (curret = 0-0-2) : Destiatio Poit Code (curret = 0-0-3) : Lik speed (56 or 64; curret=64) : 64 The system must be reset for chages to take effect. Do you wat to reset ow? (y/) (Just press Eter.) i-j-k (where i-j-k is the origiatig poit code) m-r-q (where m-r-q is the destiatio poit code) A CIC i the other protocol that will accepted umapped CICs from this SS7 protocol The poit code for the origiatig ode i the etwork Note: Get all poit codes from your etwork admiistrator. The poit code for the destiatio ode i the etwork Note: Get all poit codes from your etwork admiistrator. The lie speed for this coectio Delay i implemetatio of chages util performig a warmstart (described i Sectio E, SP201 Warmstart)
12 SP201 Istallatio Guide D.6 Chael Cofiguratio for ETSI ISDN Perform the followig procedure oce for each ISDN truk (truks 5 8). cofig dchas ISDN sigalig chael The followig is the preset Truk cofiguratio. If a chage to the Timeslot or Iterface Type is desired Eter the Truk umber you wish to modify or exit: Truk Sigalig Timeslot Truk Lik Iterface Protocol Type Type State Type ------------------------------------------------------------------------- 5 D 16 E1 Iactive Network ETSI ISDN 6 D 16 E1 Iactive Network ETSI ISDN 7 D 16 E1 Iactive Network ETSI ISDN 8 D 16 E1 Iactive Network ETSI ISDN ISDN Truk Number Eter value(5-8) or "exit" : Select iterface type - user(0) or etwork(1) : <curret=1> 1 (or 0) ISDN Iterface umber 1 assiged to Truk p, with a D Chael o timeslot 16. p where p is the port umber (5, 6, 7, or 8) ISDN truk p SP201 as the Network role (or as the User role) i this ISDN coectio Chage ISDN Sigalig Chael Eter value(1-31; curret="16") or "exit" : 16 Sigalig timeslot (The followig message appears oly if you chage the chael umber used as the sigalig timeslot.) Chages applied The card must be reset for the chages to operate properly Do you wish to reset ow (y/)? Delay i implemetatio of chages util performig a warmstart (described i Sectio E, SP201 Warmstart) ot resettig... (ISDN sigalig has bee cofigured o this truk.)
SP201 Istallatio Guide 13 D.7 Chael Cofiguratio for NI2 ISDN Perform the followig procedure oce for each ISDN truk (truks 5 8). cofig dchas ISDN sigalig chael The followig is the preset Truk cofiguratio. If a chage to the Timeslot or Iterface Type is desired Eter the Truk umber you wish to modify or exit: Truk Sigalig Timeslot Truk Lik Iterface Protocol Type Type State Type ------------------------------------------------------------------------- 5 D 24 T1 Iactive Network NI2 ISDN 6 D 24 T1 Iactive Network NI2 ISDN 7 D 24 T1 Iactive Network NI2 ISDN 8 D 24 T1 Iactive Network NI2 ISDN ISDN Truk Number Eter value(5-8) or "exit" : Select iterface type - user(0) or etwork(1) : <curret=1> 1 (or 0) ISDN Iterface umber 1 assiged to Truk p, with a D Chael o timeslot 24. p where p is the port umber (5, 6, 7, or 8) ISDN truk p SP201 as the Network role (or as the User role) i this ISDN coectio Chage ISDN Sigalig Chael Eter value(1-31; curret="24") or "exit" : 24 Sigalig timeslot (The followig message appears oly if you chage the chael umber used as the sigalig timeslot.) Chages applied The card must be reset for the chages to operate properly Do you wish to reset ow (y/)? Delay i implemetatio of chages util performig a warmstart (described i Sectio E, SP201 Warmstart) ot resettig... (ISDN sigalig has bee cofigured o this truk.)
14 SP201 Istallatio Guide E SP201 Warmstart This actio will drop ay calls that are i progress. Do you really wat to cotiue? (y/): (Iformatio o tests ad restarts) warmstart y Implemetatio of ay SS7 cofiguratio or ISDN cofiguratio (Boot baer) boot> (Do ot type aythig. The applicatio will load i a few secods.) (Iitializatios) (Applicatio baer) (Whe you see the prompt, the SP201 is ready for use.) This completes the stadard istallatio. To cofigure other parameters, see the SP201 Customizatio ad Maiteace Guide. For hardware specificatios, see the SP201 Hardware Referece Guide.