DPC 2-3mm Gap F.G.L Max. Panel Overhang 250mm Min. Rebate Depth as per NCC Reinforced Concrete Slab Slab Edge Detail (Rebate) 20mm Min. DPC FGL Cavity Closer Strip Slab Edge Detail (Overhanging) Cavity Closer Strip DPC Masonry Bolts (ø8mm Zinc Plated) FGL 20mm Min. Slab Edge Detail (Overhanging Deepened Edge Beam)
DETAILED DRAWINGS Stepdown as per NCC Engineered Floor Joists Cement Sheet Caulking Skirting Tile (Optional) Screed (Slope as per NCC) Waterproof Membrane Paving Tiles Cement Sheet DETAIL 1.4 - Balcony Detail (Timber Frame) (Min. height 150mm) Skirting Tile (Optional) Stepdown as per NCC Screed (Slope as per NCC) Paving Tiles Waterproofing Membrane DETAIL 1.5 - Balcony Detail (Concrete Slab)
100mm Bugle Head Fixing @ 600mm Ctrs DETAIL 2.1 - External Corner Detail 5-10mm Extra Stud Expansion Joint DETAIL 2.2 - Internal Corner Detail *NOTE: Internal corners require an extra stud for panel attachment 150mm back from the internal corner.
Window DETAIL 3.1 - Window Head Window Window DETAIL 3.2 - Window Jamb Rubber Seal (By Window Manufacturer) 10mm Min. Min. 15º Fall Optional Decorative Trim DETAIL 3.3 - Window Sill (Decorative Trim) Window Rubber Seal (By Window Manufacturer) 10mm Min. Min. 15º Fall DETAIL 3.4 - Window Sill
DETAIL 4.1 - Flush Eave Quad Trim (Optional) DETAIL 4.2 - Eave Detail (Panel Under) Quad Trim (Optional) DETAIL 4.3 - Eave Detail (Panel Flush With Lining)
Z (Behind ) 5-10mm Gap DETAIL 5.1 - Cladding To Brick Detail Roof Tiles 10mm Min. Cavity Closer Strip (Behind ) DETAIL 5.2 - Panel to Angle Roof Detail (Up to 25º) Roofing 35mm Min. Cavity Closer Strip Roof Structure DETAIL 5.3 - Panel to Flat Roof Detail
(Control Joint) DETAIL 6.1 - Inter Floor Junction (Panel Joint in Joist Zone) Engineered Floor Joists ( Note: For engineered floor joists, shrinkage panel gap of 5-10mm is acceptable. For non-engineered floor joists, panel gap of 15-20mm is required Inter Floor Joist Zone Inter Floor Joist Zone Engineered Floor Joists Note: To avoid control joint the joist must close within 600mm panel Inter Floor Joist Zone DETAIL 6.2 - Inter Floor Junction (No Panel Joint in Joist Zone) Meter Box Panel to Panel 100mm Bugle Head Fixing @ 600mm Centres DETAIL 7.1 - Meter Box Installation DETAIL 8.1 - Column Detail
Min. 10mm Parapet Capping (By Others) Cavity Closer Strip Metal Roofing Fixing Roof Batten DETAIL 9.1 - Parapet Detail Panel Gap* 5-10mm DETAIL 10.1 - Expansion Joint (Horizontal) *NOTE: Panel gap can be between 5-8mm for an engineered joist frame (shrinkage less than 1%), for non-seasoned joists check with frame manufacturer, or provide 15-20mm. DETAIL 10.2 - Expansion Joint (Vertical) Light Duty Fixing Anchor Rainwater Downpipe Bracket Fixing DETAIL 11.1 - External Fixings to Wall
16mm Batten To Every Stud (Max 600mm Crs) To Be Used Where External Access To Wall Is Available DETAIL 12.1 - Standard External Wall Detail Existing Building 20mm Or 50mm Depending On Boundary Wall Installation Method (Stand Up Frame Or Slide In Panels) (45mm Hex Head Screws) Top Hat Top Hat Fixing (1 leg fixed @ 600mm crs the second leg fixed to top plate, noggins and bottom plates) To Be Used Where External Access To Wall Is Not Available DETAIL 12.2 - Boundary Wall Fixing Detail A Existing Building 20mm Or 50mm Depending On Boundary Wall Installation Method (Stand Up Frame Or Slide In Panels) Batten Clip To Top Plate, Noggings & Bottom Plate (Max 600mm Crs) To Be Used Where External Access To Wall Is Not Available DETAIL 12.3 - Boundary Wall Fixing Detail B
min. 50mm min. 50mm Capping over Boundary Wall Cavity Existing Dwelling Capping over Boundary Wall Cavity Roof Detail as per NCC Roof Detail as per NCC Existing Dwelling Metal Tophat Metal Tophat Tophat fixing Tophat fixing DPC 150 step down 2-3mm Gap DPC 150 step down 2-3mm Gap min. 70mm DETAIL 13.1 - Boundary Wall Detail (Even Slab) min. 70mm DETAIL 13.2 - Boundary Wall Detail (Uneven Slabs)
min. 20mm min. 20mm Capping over Boundary Wall Cavity (Required) Existing Dwelling Capping over Boundary Wall Cavity (Required) Roof Detail as per NCC Metal Tophat Roof Detail as per NCC Metal Tophat Existing Dwelling Tophat fixing Tophat fixing DETAIL 13.3 - Boundary Wall Detail (Even Slab, Without Slab Rebate) DETAIL 13.4 - Boundary Wall Detail (Uneven Slabs, Without Slab Rebate)