NPO, X7R, Y5V/Z5U dielectric All standard chip sizes 13" reel size available Our range of SMD multi-layer ceramic capacitors compliments the leaded capacitors available in radial and aial form. All product packaging is fully marked with date and lot traceability information. Most industry standard sizes are available, including 0402 and 1812. OUTLINE DRAWING T L L W T P W Size Code mm mm mm mm Indicates termination area Dimensions in mm P C P 0402 ± 0.5±0.05 0.6 MAX 0.2 0603 1.6±5 0.8± 0.9 MAX 0.3 0805 2.0±0.2 1.25±5 1.3 MAX 0.5 1206 3.2±0.2 1.6±5 1.3 MAX 0.5 12 3.2±0.3 2.5±0.3 1.7 MAX 0.5 1812 4.5±0.3 3.2±0.3 1.6 MAX 0.5 2220 5.7±0.4 5±0.4 2.0 MAX 0.5 TOLERANCES materials, capacitance values and tolerances are only available in the following combinations. Available Tolerances Tolerance Codes ± 0.25pF, ± 0.5pF E12 Values B = ± pf COG ± 1% C = ± 0.25pF ± 2% D = ± 0.5pF ± 5% F = ± 1% G = ± 2% J = ± 5% K = ± % M = ± 20% Z = -20 + 80% X7R/ X5R ± 5%, ± 20% E12 Values ** Y5V ± 20%, -20 + 80% E6 Values Z5U ± 20%, -20 + 80% E6 Values ORDERING INFORMATION DS U 0805 C Part Voltage Size 1 J N Value Tolerance Plating U = 50/63V A = 0V F = 200V E = 25V C = 16V B = V J = 500V G = 250V D = 6.3V 0402 0603 0805 1206 12 1812 2220 C = NPO R =- X7R X = X5R G = Y5V W = Z5U Eample 1 = 0pF 2 = 1nF 3 = nf 4 = 0nF See Above ** for code N = Nickel barrier 13
RANGE ULTRA STABLE CERAMIC CHIP CAPACITORS NICKEL BARRIER TERMINATIONS NPO Case Size 0402 0603 0805 1206 12 1812 Rated Voltage (VDC) 16 50 0 16 50 0 16 50 0 16 50 0 16 50 0 50 0 0.5pf(0R5) pf (1R0) 1.2pf (1R2) 1.5pf(1R5) 1.8pf (1R8) 2.2pf (2R2) 2.7pf (2R7) 3.3pf (3R3) 3.9pf (3R9) 4.7fpf(4R7) 5.6pf (5R6) 6.8pf (6R8) 8.2pf (8R2) pf(0) 12pf (120) 15pf (150) 18pf (180) 22pf (220) 27pf (270) 33pf (330) 39pf (390) 47pf (470) 56pf (560) 68pf(680) 82pf (820) 0pf (1) 120pf (121) 150pf (151) 180pf (181) 220pf (221) 270pf (271) 330pf (331) 390pf(391) 470pf (471) 560pf (561) 680pf (681) 820pf (821) 1,000pf (2) 1,200pf (122) 1,500pf (152) 1,800pf (182) 2,200pf (222) 2,700pf (272) 3,300pf (332) 3,900pf (392) 4,700pf (472) 5,600pf (562) 6,800pf (682) 8,200pf (822) 0.01uf (3) 0.012uf (123) 0.015uf (153) 0.018uf (183) 0.022uf (223) 0.027uf (273) 0.033uf (333) 0.039uf (393) 14
RANGE STABLE CERAMIC CHIP CAPACITORS NICKEL BARRIER TERMINATIONS X7R Case Size 0402 0603 0805 1206 12 1812 Rated Voltage (VDC) 16 25 50 16 25 50 0 16 25 50 0 16 25 50 0 25 50 0 25 50 0 0pf (1) 120pf (121) 150pf (151) 180pf(181) 220pf (221) 270pf (271) 330pf (331) 390pf (391) 470pf (471) 560pf (561) 680pf (681) 820pf (821) 1,000pf (2) 1,200pf (122) 1,500pf (152) 1,800pf (182) 2,200pf (222) 2,700pf (272) 3,300pf (332) 3,900pf (392) 4,700pf (472) 5,600pf (562) 6,800pf (682) 8,200pf (822) 0.0uf (3) 0.012uf (123) 0.015uf (153) 0.018uf (183) 0.022uf (223) 0.027uf (273) 0.033uf (333) 0.039uf (393) 0.047uf (473) 0.056uf(563) 0.068uf (683) 0.082uf (823) 0.uf (4) 2uf (124) 5uf(154) 8uf(184) 0.22uf(224) 0.27uf (274) 0.33uf (334) 0.39uf (394) 0.47uf (474) 0.56uf (564) 0.68uf (684) 0.82uf (824) uf (5) 15
RANGE Dialectric X5R Case Size 0402 Rated Voltage (VDC) 16 0.033uf (333) 0.047uf (473) uf (4( For other case sizes and higher 0402 capacitance see DS - High. General Purpose Ceramic Chip Capacitors Y5V/Z5U Nickel Barrier Terminations Dialectric Y5V/Z5U Case Size 0402 0603 0805 1206 12 1812 Rated Voltage (VDC) 16 25 50 16 25 50 16 25 50 0 25 50 0 50 0 50 0 0.0uf (3) 0.015uf (153) 0.022uf (223) 0.033uf (333) 0.047uf (473) 0.068uf (683) 0.uf (4) 5uf (154) 0.22uf (224) 0.33uf (334) 0.47uf (474) 0.68uf (684) uf (5) TAPE DIMENSIONS (mm) Type P Type C D 0 E A 0 F W B 0 G t t K 1 P P 2 P 0 directional of unreeling W Type D0 P P0 P2 E F G t 8.0 ± 0.3 C 1.5 +, -0 4.0 ± 4.0 ± 2.0 ± -0.05 1.75 ± 3.5 ± 0.05 0.75 min 1.1 ma 8.0 ± 0.3 P 1.5 +, -0 4.0 ± 4.0 ± 2.0 ± 0.05 1.75 ± 3.5 ± 0.05 0.75 min 0.3 ma 12.0 ± 0.3 P 1.5 +, -0 8.0 ± 4.0 ± 2.0 ± 0.05 1.75 ± 5.5 ± 0.05 0.75 min ma C = Card P = Plastic REEL DIMENSIONS (mm) 12.75 +5-0 2 ± 0.5 Nom. Tape Width A W1 8 180 or 330 +0-2 8.4 +1.5-0 12 180 or 330 +0-2 12.4 +2-0 62 ± 1.5 20.5 +0.5-0 W 1 16
PERFORMANCE CHARACTERISTICS PERFROMANCE CHARACTERISTICS 1. ELECTRICAL Code COG X7R X5R Y5V Z5U General Eamples of Applications COG dielectrics are very stable. Temperature, frequency and time vary little. Typical applications are in tuned circuits, timing circuits and fast rise time X7R dielectrics offer higher capacitance for a given case size than COG. bypass, coupling and filtering X5R dielectrics offer higher capacitance for a given case size than X7R. Applictaions would include bypass, coupling and filtering Y5V dielectrics offer the highest capacitance for a given case size than X5R. bypass and decoupling circuits or where temperature dependence is not of major importance. Z5U dielectrics offer the highest cpacitance for a given case size than Y5V. bypass and decoupling circuits or where temperature dependance is not of major importance. Temperature Range - 55 to + 125-55 to + 125-55 to + 85-25 to + 85-25 to + 85 Insulation Resistance (I.R.) after 1 min charging at Rated Voltage > 0G ohms or 00 sec whichever is less >0G ohms or 00 sec whichever is less Voltage Ratings dc 50, 0, 200, 500, 16, 25, 50, 0, 200, 500 >0G ohms or 00sec >G ohms or 0 sec,16,25,50, 16, 25, 50, 0 25, 50 >G ohms or 0 sec Proof Voltage 2.5 rated voltage 2.5 rated voltage 2.5 X rated voltage. 2 rated voltage 2.5 rated voltage Ma allowable Variation over Temperature Range C > 20pf : 0 ± 00ppm/ C C < 20pF : see CECC 32 1-801 ± 15% ± 15% +30% to - 80% +22% to - 56% 2. ENVIRONMENT Test Conditions Requirement Resistance to soldering heat Adhesion Rapid change or Temperature Components completely immersed in a solder bath at 260 ± for 5 secs. Component mounted to substrate a force of 5N applied normal to the line joining the termination and in a line parallel to the substrate. - 55 to 125 C, 5 cycles (1B, 2C1) - 25 to +85, 5 cycles (2F4) 25% Ma leaching on each edge No visible damage No visible damage. After recovery C/C ±1% or pf COG C/C ±% X7R C/C ±% X5R C/C ±20% Y5V Tan 1.5 specified value IR. 0.25 specified value 17
3. AGEING and impedance will vary depending on circuit operating conditions and the type of dielectric used - typical performance graphs relating to these materials are shown below. 3.1 FREQUENCY 0 IMPEDANCE nf 0 0 nf IMPEDANCE/ESR (OHMS) ESR CAPACITANCE (nf) TAN CAPACITANCE IMPEDANCE/ESR (OHMS) IMPEDANCE ESR 0 00 0.01 0 0 00 Z (Ω) 0 0.01 22 nf 47 nf 0 nf 220 nf 470 nf 1 F 1.5 F nf 4.7 nf 0 F (MHz) 0 nf 00 IMPEDANCE/ESR (OHMS) IMPEDANCE ESR CAPACITANCE (nf) 0 TAN CAPACITANCE 0 00 0.001 0.01 3.2 TEMPERATURE 18
SURFACE MOUNT CERAMIC SMD MULTI-LAYER HIGH CAPACITANCE DS High capacitance range complimenting the standard DS range Available in X7R, X5R, Y5V and Z5U Suitable for many applications including digital consumer goods and high resolution LCD displays OUTLINE DRAWING T L L W T P W Indicates termination area Size Code mm mm mm mm 0402 ± 0.5±0.05 0.6 MAX 0.2 0603 1.6±5 0.8± 0.9 MAX 0.3 0805 2.0±0.2 1.25±5 1.3 MAX 0.5 1206 3.2±0.2 1.6±5 1.3 MAX 0.5 12 3.2±0.3 2.5±0.3 1.7 MAX 0.5 1812 4.5±0.3 3.2±0.3 1.6 MAX 0.5 Dimensions in mm P C P TOLERANCE DIELECTRIC MATERIALS, CAPACITANCE VALUES AND TOLERANCE AVAILABLE Available Tolerance Tolerance Codes X7R +/- %, +/- 20% As Tables K=% M=20% X5R +/- %, +/- 20% As Tables K=% M=20% Y5V +/- 20%, - 20% + 80% As Tables M=20% Z= -20% + 80% Z5U +/- 20%, - 20% + 80% As Tables M=20% Z= -20% + 80% ORDERING INFORMATION DS B 0805 X Part Voltage Size 6 K N Value Tolerance Plating U = 50 E = 25V C = 16V B = V D = 6.3V 0402 0603 0805 1206 12 1812 R =- X7R X = X5R G = Y5V W = Z5U Eample 4 = 0nF 5 = 1µF 6 = µf K = % M = 20% Z = 20+80% N = Nickel barrier 19
SURFACE MOUNT CERAMIC SMD MULTI-LAYER HIGH CAPACITANCE DS RANGE X7R Case Size 0603 0805 1206 12 Rated Voltage (VDC) 16 25 50 16 25 50 16 25 50 25 5uF (154) 0.22uF (224) 0.33uF (334) 0.47uF (474) uf (5) 1.5uF (155) 2.2uF (225) 3.3uF (335) 4.7uF (475) uf (6) X5R Case Size 0402 0603 0805 1206 12 Rated Voltage (VDC) 6.3 6.3 16 25 6.3 16 25 6.3 16 25 16 25 0.22uF (224) 0.33uF (334) 0.47uF (474) 0.68uF (684) 0.82uF (824) uf (5) 1.2uF (125) 1.5uF (155) 1.8uF (185) 2.2uF (225) O O O O O O 3.3uF (335) O O O 4.7uF (475) O O O O 6.8uF (685) O O O 8.2uF (825) O O O uf (6) O O O O O 12uF (126) O O 15uF (156) O O 22uF (226) F O O O 33uF (336) 47uF (476) O 0uF (7) F=Future o=reflow Only General Purpose Ceramic Chip Capacitors Y5V/Z5U Nickel Barrier Terminations Y5V/Z5U Case Size 0603 0805 1206 12 1812 Rated Voltage (VDC) 16 6.3 16 25 16 25 16 25 35 16 25 1.5uF (155) 2.2uF (225) 3.3uF (335) 4.7uF (475) 6.8uF (685) uf (6) 22uF (226) 47uF (476) 0uF (7) 20
SURFACE MOUNT CERAMIC SMD MULTI-LAYER HIGH CAPACITANCE DS TAPE DIMENSIONS (mm) Type P Type C D 0 A 0 B 0 E F G W t t K 1 P P 2 P 0 directional of unreeling W Type D0 P P0 P2 E F G t 8.0 ± 0.3 C 1.5 +, -0 4.0 ± 4.0 ± 2.0 ± -0.05 1.75 ± 3.5 ± 0.05 0.75 min 1.1 ma 8.0 ± 0.3 P 1.5 +, -0 4.0 ± 4.0 ± 2.0 ± 0.05 1.75 ± 3.5 ± 0.05 0.75 min 0.3 ma 12.0 ± 0.3 P 1.5 +, -0 8.0 ± 4.0 ± 2.0 ± 0.05 1.75 ± 5.5 ± 0.05 0.75 min ma C = Card P = Plastic REEL DIMENSIONS (mm) 2 ± 0.5 Nom. Tape Width A W1 8 180 or 330 +0-2 8.4 +1.5-0 12 180 or 330 +0-2 12.4 +2-0 12.75 +5-0 62 ± 1.5 20.5 +0.5-0 PERFORMANCE CHARACTERISTICS W 1 PERFROMANCE CHARACTERISTICS 1. ELECTRICAL Code X7R X5R Y5V Z5U General Eamples of Applications X7R dielectrics offer higher capacitance for a given case size than COG. bypass, coupling and filtering X5R dielectrics offer higher capacitance for a given case size than X7R. Applictaions would include bypass, coupling and filtering Y5V dielectrics offer the highest capacitance for a given case size than X5R. bypass and decoupling circuits or where temperature dependence is not of major importance. Z5U dielectrics offer the highest cpacitance for a given case size than Y5V. bypass and decoupling circuits or where temperature dependance is not of major importance. Temperature Range -55 to + 125-55 to + 85-25 to + 85-25 to + 85 Insulation Resistance (I.R.) after 1 min charging at Rated Voltage >0G ohms or 00 sec whichever is less >0G ohms or 00sec >G ohms or 0 sec >G ohms or 0 sec Voltage Ratings dc, 16, 25, 50,16,25, 16, 25, 35, 16, 25, 35 Proof Voltage 2.5 rated voltage 2.5 X rated voltage. 2 rated voltage 2.5 rated voltage Ma allowable Variation over Temperature Range ± 15% ± 15% +30% to - 80% +22% to - 56% 2. ENVIRONMENT Test Conditions Requirement Resistance to soldering heat Adhesion Components completely immersed in a solder bath at 260 ± for 5 secs. Component mounted to substrate a force of 5N applied normal to the line joining the termination and in a line parallel to the substrate. Rapid change or Temperature - 55 to 125 C, 5 cycles (1B, 2C1) - 25 to +85, 5 cycles (2F4) 25% Ma leaching on each edge No visible damage No visible damage. After recovery C/C ±1% or pf COG C/C ±% X7R C/C ±% X5R C/C ±20% Y5V Tan IR. 1.5 specified value 0.25 specified value 21