1 2 3 4 IP Help Point Stations These vandal resistant Help Point Columns have many uses. In public areas they serve as information and help points for passers-by to request help and receive assistance in cases of emergency. 1. Y100056-1IP IP Help Point station with a programmable large red emergency call button, electret microphone with multifunction LED, loudspeakers 2 x 8 Ω, 3 inputs for floating contacts and 2 relay outputs (connection as make or break contact), protection classifi cation IP 65 and IK 07, material stainless steel 2. Y100056-2IP IP Help Point station with a programmable large red emergency call button, with colour video camera with configurable white light illumination and integrated heater (can be operated as IP network camera or as analogue camera), electret microphone with multifunction LED, loudspeakers 2 x 8 Ω, 3 inputs for floating contacts and 2 relay outputs (connection as make or break contact), tamper protection switch, protection classifi cation IP 65 and IK 07, material stainless steel, angle of camera adjustable up to 30 horizontally/vertically. 3. Y100056-3IP IP Help Point station with a programmable large red emergency call button, with 3.5 Colour-TFT display for graphical menu navigation and display of IP video streams or analogue video signals (PAL or NTSC), display resolution 320x240 pixels with 65,000 colours, with colour video camera with configurable white light illumination and integrated heater (can be operated as IP network camera or as analogue camera), electret microphone with multifunction LED, loudspeakers 2 x 8 Ω, 3 inputs for floating contacts and 2 relay outputs (connection as make or break contact), tamper protection switch, protection classifi cation IP 65 and IK 07, material stainless steel, angle of camera adjustable up to 30 horizontally/vertically. 4. Y100056-4IP IP Help Point station same as Y1000056-2IP but with one additional lower station, designated for car and truck gateways. Datasheet Version 1.2/0112 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 1 10
Technical Data Benefits Technical data IP rating: IP 65 ing: IK 07 Front panel: stainless steel (1.4301), 3 mm (0.12 in) Back panel: stainless steel (1.4301), 3 mm (0.12 in) powder coated black Microphone: Omnidirectional electret microphone for max. 7 m (23 ft) speaking distance Loudspeaker: Special membrane type for optimal sound quality, sound pressure: 85 db/1 W/1 m (3.28 ft), 2 x 8 Ω Amplifier: integrated class D amplifier with 2.5 W Input: 3 inputs for floating contacts (detection of 5 input states) Output: 2 relay outputs (switch-over contacts) 30 V / 1 A Line output: for connection loudspeaker module Call indication: multifunction LED (colours: red, green, blue) Display: 3,5 Colour-TFT display, graphical menu navigation display of IP video streams (MJPEG) or analogue video signals (PAL or NTSC) 320 x 240 Pixel, 65000 colours Call button: large red emergency call button Frequency range: 16000 Hz Operating temperature range: 20 C to 60 C ( 4 F to 140 F) Storage temperature range: 20 C to 60 C ( 4 F to 140 F) Relative humidity: up to 95% not condensing Connection: - pluggable screw terminals IP Uplink: shielded RJ 45 modular jacks Analogue video signal: BNC, 75 Ω Power supply: Y100056-1 PoE or external supply 12 24 VAC or 15 35 VDC power consumption: max. 4 W camera PCB PoE or external supply 22 24 VAC or 20 35 VDC power consumption: max. 13 W TFT- Display PCB PoE or external supply 22 24 VAC or 20 35 VDC power consumption: max. 9.8 W Cabling: min. Cat. 5 PoE (Power over Ethernet): IEEE 802.3af standard Power consumption of the terminal device: Class 3 (6.49 W to 12.95 W) Protocol: IoIP-Protocol based on UDP/IP Ethernet IEEE 802.3, 802.1q, IP Protocol (RFC 791) ICMP (RFC 792), UDP (RFC 768) TCP (RFC 793), QoS / Diffserv RFC 2474 Data rate: 10/100 MBit/s (Full/Half Duplex) Measurements: W 220 mm, H 1810 mm, D 220 mm (W 8.66 in, H 71.26 in, D 8.66 in) (Measurements without camera dome) Shipping box: W 320 mm, H 2050 mm, D 320 mm (W 12.6 in, H 80.7 in, D 12.6 in) Weight incl. packaging: approx. 80 kg (176 lbs) technical data Hybrid camera General data: Image sensor: 1/4 inch colour CMOS sensor Lens: Focal distance 3.86 mm (0.01 inch), F2,8, fixed aperture, angle 53 (horizontal) and 63 (diagonal) Automatic adjustment of white fader-, colour-, contrast- and brightness parameters Angle adjustable up to 30 horizontally/vertically IP video stream: Resolution: 320 x 240 or 640 x 480 Video format: Motion JPEG (MJPEG) Picture rate: Up to 30 pictures per second Protocols: HTTP, ARP, UDP, TCP, IP, ICMP, DHCP (Client) Ethernet: 10/100 MBit/s, half-/full duplex Standard http-url for display/integration in 3 rd party systems (e.g. webbrowser): http://<ip address>/video.cgi Storage of 5 frames ( Snapshots ) and call up via http://<ip address>/snapshot<1 5>.jpg, possible Analogue CVBS video signal: Supported video systems: PAL and NTSC Resolution PAL: 720 x 576 Resolution NTSC: 720 x 480 Camera illumination/camera heater: LED-white light illumination and camera heater auto matically or manually configurable Configuration: Via CCT 800 or Via webinterface http://<ip address>, recommended browsers: min. Internet Explorer 8, min. Mozilla Firefox 3.5 benefits Intercom stations with built-in colour video camera Vandal resistant Protection classification IP 65 and IK 07 Supports DSP-Features such as OpenDuplex, Audio Monitoring, Microphone- / Loudspeaker Surveillance, etc. 3,5 Colour-TFT display with integrated webinterface http://<ip address> Display of IP video streams (MJPEG), static graphics (JPEG) or analogue CVBS video signal Supported analogue video systems: PAL and NTSC Works under all conditions 99,998 % availability around the clock Individually painting Individually logos ( SOS / EMERGENCY / HELP /...) Extent of Supply Help Point Station 3 x paste-on labels ( SOS / EMERGENCY / HELP ) for emergency call button Stand support and mounting kit Line length in LAN The maximum line length of Cat. 5 cabling in a LAN is 100 m (328 ft) e.g. from switch to Intercom station. Datasheet Version 1.2/0112 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 2 10
System/Network Requirements SysteM REQUIREMENTS GE 800 (min. PRO 800 1.1) with G8-IP (min. G3-8-IP 4.0b01) GE 300 (min. PRO 800 1.1) with G3-IP (min. G3-8-IP 4.0b01) GE 700 with GE700-UPG (min. PRO 800 1.1) with G7-DSP-IP Configuration software min. CCT 800 1.1 Configuration software IPStationConfig (included in setup of CCT 800 1.1) requirements to the network IP-Addresses and Ports For the Help Point the DHCP functionality is available. If DHCP is not used, the station must have a fixed IP-address. In case of a changing public IP-address, dynamic registration of a Help Point is possible. Communication from the program IPStationConfig is done via Port 16399 (can not be configured). Communication from the Emergency Station to the Intercom Server (UDP protocol) is done via port 16400 (configurable). VPN compatible QoS Requirements Maximum One-Way-Delay 100 ms Delay-Jitter not above 50 ms 0% packet loss for perfect audio quality Bandwidth The required bandwidth depends on the desired number of speech links: Bandwidth incl. protocol overhead per IP-Intercom terminal, for upload and download: 3,5 khz 7 khz 16 khz Bandwidth (speech and date): 96 kbit/s 96 kbit/s 143 kbit/s Speech is compressed to: G.711 standard G.722 standard G.722 standard Datasheet Version 1.2/0112 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 3 10
precautions When opening the stations ESD precautions must be observed. The stations may only be opened by authorised service engineers. Restriction Video: Video data can not be transmitted over WAN! Power Supply Y100056-1IP: Power supply via PoE or external supply Y100056-2IP: Power supply must be connected to camera PCB (for supply via PoE and external supply) When using analogue video an isolated power supply unit is mandatory Y100056-3IP: 2 power supply units are required. The camera PCB and the TFT-display PCB need a own power supply. Power supply must be connected to camera PCB or TFT-display PCB (for supply via PoE and external supply) When using analogue video an isolated power supply unit is mandatory Y100056-3IP: 2 power supply units are required. Both camera PCB s need an own power supply. Power supply must be connected to camera PCB (for supply via PoE and external supply) When using analogue video an isolated power supply unit is mandatory General Notes: For use of external supply in case of a PoE capable network link, an appropriate configuration of the switch is required (Ethernet port may not be blocked)! The analogue video output can even be used with PoE power supply. Datasheet Version 1.2/0112 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 4 10
measurements camera dome Measurements in mm (inch), not to scale! connection camera PCB AC/DC AC/DC+ 20 V DC 35 V DC 22 V AC 24 V AC Jumper Power supply: Locking screw Switch for analogue video signal: PAL Tilting the camera: Unscrew locking screw AC/DC AC/DC+ PoE camera PCB Analogue video signal NTSC Tilt camera into desired position Tighten locking screw IP Uplink UPLINK DOWNLINK Expansion plug e.g. for access reader module for fixing cable straps OUT 1 OUT 1 Slots for inserting button labels External loudspeaker module OUT 2 OUT 2 Handset: Microphone Loudspeaker MUTE GND LINE LINE+ IN 1 IN 2 IN 3 GND EP+ EP EM+ EM 20 Ethernet connection: The RJ 45 socket on the camera PCB must be used! Datasheet Version 1.2/0112 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 5 10
connection TFT display PCB Jumper Power supply: AC/DC AC/DC+ IP Uplink PoE Analogue video signal AC/DC AC/DC+ 15 V DC 35 V DC 22 V AC 24 V AC TFT display PCB Expansion plug e.g. for access reader module for fixing cable straps OUT 1 OUT 1 External loudspeaker module OUT 2 OUT 2 Handset: Microphone Loudspeaker MUTE GND LINE LINE+ IN 1 IN 2 IN 3 GND EP+ EP EM+ EM Ethernet connection: The RJ 45 socket on the TFT display PCB must be used! Datasheet Version 1.2/0112 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 6 10
Measurements Measurements in mm (inch), not scale! Measurements Help Point: Measurements stand support: 6 x Ø6 (Ø0.24) 4 x M12 Ø75 (Ø2.95) 10 (0.39) 107 (4.21) 150 (5.95) 1374 (54.09) 1618 (63.70) 1810 (71.26) 1059 (41.69) 1695 (66.73) 53 (2.08) 160 (6.3) 208 (8.19) 220 (8.66) 155 (6.1) 220 (8.66) Datasheet Version 1.2/0112 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 7 10
Measurements Measurements in mm (inch), not scale! Measurements Help Point Y100056-4IP: 220 (8.66) 1059 (41.69) 1129 (44.45) 1206 (47.48) 1548 (60.94) 1618 (63.70) 1695 (66.73) 1810 (71.26) 220 (8.66) Datasheet Version 1.2/0112 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 8 10
Mounting Instructions Mounting the pedestal (1) Option 1: Encase the pedestal in concrete Option 2: Bolt the pedestal to the ground. Levelling of the mounting plate (2) Level the stand support with nuts and washers (in extent of supply). Open the Help Point Open the lock-out release for the door lock (3) Unlock the door (4) Open door of the Help Point. Mounting the Help Point Thread the mounting openings from the Help Point into the stand support. Secure the help point with the nuts and washers (in extent of supply). Check the Help Point if mounted firmly. Close the Help Point door Lock the door (4) Close the lock-out release for the door lock (3) 4 3 2 1 Datasheet Version 1.2/0112 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 9 10
COMMEND A Strong Network Worldwide Europe America SWITZERLAND LIECHTENSTEIN Commend AG Tel. +41-44-955 02 22 www.commend.ch USA CANADA LATIN AMERICA Commend Inc. Tel. +1-201-529-2425 www.commendusa.com FRANCE Commend France S.A.S. Tel. +33-149 18 16 40 www.commend.fr SPAIN PORTUGAL ITALY Commend Ibérica S.L. Tel. +34-91-395 24 98 www.commend.es Commend Italia S.R.L. Tel. +39-035-95 39 63 www.commend.it Asia-Pacific AUSTRALIA NEW ZEALAND Commend Australia Tel. +61-3-9729-3700 (Melbourne) Tel. +61-2-4655-5738 (Sydney).au NETHERLANDS BELGIUM LUXEMBURG AUSTRIA SLOVENIA RUSSIA HUNGARY CROATIA SERBIA BOSNIA-HERZEGOVINA MONTENEGRO MACEDONIA KOSOVO ALBANIA Commend Benelux B.V. Tel. +31-76-200 01 00 www.commend.nl Commend Österreich GmbH Tel. +43-1-715 30 79 www.commend.at Commend Adria d.o.o. Tel. +385-1-369 11 23 www.commend.hr CHINA SINGAPORE ISRAEL Commend Business Hub China Tel. +86-21-52 13 19 28 www.commend.cn Commend Business Hub Asia Isolectra Far East Pte. Ltd Tel. +65-6272-2371.sg Sberlophone Ltd Tel. + 972-4-834 10 32 www.sberlophone.co.il SLOVAKIA CZECH REPUBLIC Commend Slovakia spol. s r.o. Tel. +421-2-58 10 10 40 www.commend.sk Africa UNITED KINGDOM IRELAND SWEDEN NORWAY FINLAND DENMARK ICELAND Commend UK Ltd Tel. +44-1279-87 20 20 www.commend.co.uk Commend Business Hub Nordic JNT Sound System AB Tel. +46-8-99 30 60 www.jnt.se SOUTH AFRICA ALGERIA TUNISIA MOROCCO Commend Business Hub South Africa Evolving Management Solutions (Pty) Ltd Tel. +27-11-274 6665 www.commend.co.za Commend France S.A.S. Tel. +33-149 18 16 40 www.commend.fr POLAND C&C Partners Telecom Sp.z o.o. Tel. +48-65-525 55 55 www.ccpartners.pl Other countries GERMANY Schneider Intercom GmbH Tel. +49-211-88285-333 www.schneider-intercom.de Commend International GmbH Tel. +43-662-85 62 25 Datasheet Version 1.2/0112 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 10 10