D/N VANDAL RES. VARI-FOCAL DOME CAMERA

Transcription

1 D/N VANDAL RES. VARI-FOCAL DOME CAMERA PIH-2342X/2346X W/S INSTRUCTION MANUAL

2 IMPORTANT SAFEGUARDS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. GRAPHIC SYMBOL EXPLANATION The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit.

3 PART DESCRIPTION & DIMENSION Unit mm BASE DOME COVER HOLE PLUG SIDE HOLE

4 INSTALLATION 1. Please use the enclosed screw driver to untighten the 4 tamper-proof screws on the dome cover. 2. Put the provided screws (M3.0 x 25, wooden screw) through the holes marked as "a", and fix the base in the desired area (FIG.1). a a FIG. 1 a 3. Firstly, put video cable and power cable through a pipe with 1/2" PT at one end (FIG.2), and connect the cables to the terminal block on the PCB accordingly and then screw the pipe to the side hole (FIG.3, please make sure the connection between the pipe and the side hole is watertight.). NOTE : Pipe is not provided. INPUT VIDEO GND VIDEO OUT POWER FIG. 2 FIG. 3

5 4. The direction of the lens is adjustable through the adjustable Pan/Tilt brackets and rotatable round bracket for Azimuth. The lens can be adjusted easily by hand without using screw driver. Please refer to FIG.4. TILT IRIS LEVER VR SCREW DRIVER AZIMUTH BRACKET ZOOM OR FOCUS ADJUSTMENT FOCUS OR ZOOM ADJUSTMENT PAN FIG An extra RCA jack for easy installation. Plug the video input of monitor to the RCA jack and adjust focus and zoom. After finished, unplug the RCA jack. Please refer to FIG.5. FIG. 5

6 6. Adjust DC iris level by turning the iris level VR. Please refer to FIG.4. ATTENTION: Adjust this VR with care so as not to cause damage to the unit. 7. Put on the dome cover first. Then tighten the tamper-proof screws (FIG.6). FIG. 6

7 Alternative cabling positions 1. Untighten the hole plug on the bottom of the base and screw it to the side hole. 2. Put the video cable and power cable through the bottom hole and connect them to the terminal block on the PCB accordingly. Please refer to INSTALLATION Step3 for waterresistant installation. 3. Fix the cable with cable clamp. INPUT VIDEO GND VIDEO OUT POWER

8 SPECIFICATIONS D/N VANDAL RESISTANT VARI-FOCAL DOME CAMERA Model No. Focal Length PIH-2342XWN/P 3.3~12mm PIH-2342XSN/P 9~22mm Iris F1.4 Lens H 89.8 ~ ~ 13.1 Angle of view V 63.6 ~ ~ 9.8 D ~ ~ 16.3 Power Input Voltage System Sync. Mode Pick Up Element DC12V ( 10%) NTSC or PAL Internal 1/3" Super HAD CCD Sensor Effective Pixels Chip Size Horizontal & Vertical Sync. Frequency Scanning System Infrared Cut Filter Resolution Minimum Illumination S/N Ratio Auto Gain Control White Balance Aperture Correction Power Consumption Back Light Compensation Video Output Operating Temperature Gamma Characteristic IP Rating Vandal Proof Dimension Weight 768(H) x 494(V) [NTSC] 752(H) x 582(V) [PAL] 5.59mm (H) x 4.68mm (V) KHz / 59.94Hz [NTSC] KHz / 50Hz [PAL] 2 1 Interlace Auto Selectable Automatic Switch From Color Mode To Monochrome Color: 540TV Lines, Mono: 600TV Lines Color: 0.05Lux at F1.4, 0Lux with IR Mono: 0.01Lux at F1.4 More Than 50dB (AGC OFF) 36dB Variable Gain ATW Horizontal, Vertical 2.2W Auto CVBS 1.0Vp-p, 75ohm -10 ~ +50 (14 ~ 122 ) =0.45 IP68 Withstand a blow from a 10 lbs sledgehammer Base : 136 x 55mm, Dome : g Design and specifications are subject to change without notice.

9 Model No. Lens D/N VANDAL RESISTANT VARI-FOCAL DOME CAMERA Focal Length Iris Angle of view Power Input Voltage System Sync. Mode Pick Up Element H V D PIH-2346XWN/P 3.3~12mm 89.8 ~ ~ ~ 29.9 F1.4 PIH-2346XSN/P 9~22mm 32.1 ~ ~ ~ 16.3 DC12V ( 10%) or AC24V ( 10% ) NTSC or PAL Internal 1/3" Super HAD CCD Sensor Effective Pixels Chip Size Horizontal & Vertical Sync. Frequency Scanning System Infrared Cut Filter Resolution Minimum Illumination S/N Ratio Auto Gain Control White Balance Aperture Correction Power Consumption Back Light Compensation Video Output Operating Temperature Gamma Characteristic IP Rating Vandal Proof Dimension Weight 768(H) x 494(V) [NTSC] 752(H) x 582(V) [PAL] 5.59mm (H) x 4.68mm (V) KHz / 59.94Hz [NTSC] KHz / 50Hz [PAL] 2 1 Interlace Auto Selectable Automatic Switch From Color Mode To Monochrome Color: 540TV Lines, Mono: 600TV Lines Color: 0.05Lux at F1.4, 0Lux with IR Mono: 0.01Lux at F1.4 More Than 50dB (AGC OFF) 36dB Variable Gain ATW Horizontal, Vertical 3.0W (DC12V), 2.5W (AC24V) Auto CVBS 1.0Vp-p, 75ohm -10 ~ +50 (14 ~ 122 ) =0.45 IP68 Withstand a blow from a 10 lbs sledgehammer Base : 136 x 55mm, Dome : g Design and specifications are subject to change without notice CSE-3

10 MERIT LILIN ENT. CO., LTD CSE