Loop-IP6510 Multiple WAN Router/Bridge

Transcription

1 Loop- Multiple WAN Router/Bridge Features Supports 10/100 BaseT speed auto-sensing, half/full duplex auto-negotiation and auto MDI/MDI-X crossover WAN interfaces 2 built-in 10/100BaseT WAN interfaces for uplink 2 cold plug-in slots supporting any 2 of the following cards: E1 card: 2 ports per card, up to 4 ports per system T1 card: 2 ports per card, up to 4 ports per system Ethernet card: 1 port per card, up to 2 ports per system LAN interfaces Four 10/100BaseT LAN interfaces for downlink RS232 console port Supports SNMP management Supports Telnet and SSH remote management Supports remote software upgrade Supports 802.1a, 802.1w, 802.1q and 802.1ad Supports remote bridges Supports router Description The Loop- Router/Bridge provides remote bridge connectivity from 4 Ethernet ports to 2 fixed WAN ports and also to 2 optional WAN slots. Whereas the 2 fixed WAN ports are always Ethernet, choices are available for the 2 optional WAN slots. Each of the 2 optional slots can accept one of 3 choices of plug-in cards, which are (a) a card with dual T1 port (b) a card with dual E1 port (c) a card with one 10/100 BaseT fast Ethernet port Using the optional dual E1/T1 card, up to 4 E1/T1 lines can be used for WAN connectivity, either separately or in a single bundle. All Ethernet, WAN, and LAN ports have speed auto-sensing, half/full duplex auto-negotiation, and auto MDI/MDI-X crossover features. All serial (E1/T1) WAN interfaces support PPP, MLPPP, Frame Relay, Cisco-compatible HDLC and HDLC protocols. The Loop- Router/Bridge has a DB9S console port, which allows users to execute in-service diagnostics and fault isolation from a local terminal. It also allows users to manage remotely via Telnet, SSH and SNMP through Ethernet or WAN ports. Multicolor LED indicators and an ACO (Alarm Cut Off) button are provided on the front panel. 1

2 Loop- Multiple WAN Router/Bridge Ordering Information To specify options, choose from the list below. Note: RoHS compliant units are identified by the letter G appearing at the end of the ordering code. Main Unit Loop--aa-bb-pp-RT-G Loop--aa-bb-pp-BR-G Model Description Notes 1U height ETSI (front access) unit, stand-alone with 2 built-in 10/100BaseT WAN interfaces and 4 10/100BaseT LAN interfaces, which support Bridge and Router function. 1U height ETSI (front access) unit, stand-alone with 2 built-in 10/100BaseT WAN interfaces and 4 10/100BaseT LAN interfaces, which support Bridge function only. Cold Plug-in Modules Loop--2T1-G Dual T1 interface with RJ48C connector Loop--2E120-G Dual E1-120 ohm interface with RJ48C connector E1-120 ohm/t1 jumper selectable Loop--1FE-G One 10/100 BaseT Fast Ethernet Accessories Power Cord (All power cords are RoHS compliant.) Loop-ACC-PC-USA AC power cord for Taiwan/America Loop-ACC-PC-EU AC power cord for Europe Loop-ACC-PC-UK AC power cord for UK Loop-ACC-PC-AUS AC power cord for Australia Loop-ACC-PC-CH AC power cord for China User s Manual Loop--UM User s Manual (optional, printed on paper copy). A CD version of the manual is already included as standard equipment. Software Loop--UPGR-RT Activation code for Router function Where aa and bb are used to select the additional cold plug-in modules. If this option is not required, omit the aa or bb field in the ordering code aa, bb= Description Notes 2T1 2E120 1FE Dual T1 interface with RJ48C connector Dual E1-120 ohm interface with RJ48C connector One 10/100 BaseT Fast Ethernet E1-120 ohm/t1 jumper selectable Where pp is used to select a power supply pp = Description Notes P9 Hybrid 100 to 240 Vac and -48 Vdc (-36 to -72 Vdc) coexist fixed power supply For AC, choose an appropriate power cord. 2

3 Loop- Multiple WAN Router/Bridge Loop- Product Specifications Ethernet WAN Interface Two built-in 10/100BaseT Ethernet ports (WAN1 and WAN2) Speed auto-sensing Half/full duplex auto-negotiation Auto MDI/MDI-X crossover WAN Plug-in Module E1 card: 2 ports per card, up to 4 ports per system T1 card: 2 ports per card, up to 4 ports per system Ethernet card: 1 port per card, up to 2 ports per system Layer-two E1/T1 WAN protocols: PPP, MLPPP, HDLC, Frame Relay, Cisco compatible HDLC E1 Line Interface Line Rate 2.048M bps 50 ppm Line Code HDB3 Output Signal ITU G.703 Connector RJ48C Loopbacks Line Loopback, Payload Loopback Test Pattern 20-bit QRSS, 3-in-24, 1-in-8, 2-in-8, 1:1 T1 Line Interface Line Rate Mbps 50 bps Line Code AMI or B8ZS Output Signal DS1 Connector RJ48C Loopbacks Line Loopback, Payload Loopback Test Pattern 20-bit QRSS, 3-in-24, 1-in-8, 2-in-8, 1:1 LAN Interface 4 10/100BaseT interfaces Speed auto-sensing Half/full duplex auto-negotiation Auto MDI/MDI-X crossover Management SNMP v1, v2c Telnet SSH Bridge STP, RSTP 802.1q supported Cisco ISL packet transparent VLAN packet transparent User configurable aging time Up to 16K MAC table Padding/un-padding Ethernet FCS Support IEEE 802.1ad Q-in-Q Router Routing protocol: RIP-I, RIP-II, OSPF Static route Address Translation NAT/NAPT Static address table for NAT 3

4 Loop- Multiple WAN Router/Bridge Port forwarding table for NAPT (Virtual Service) Supports port range from 1 to DHCP DHCP server support for LAN users (RFC2131, RFC2132) BOOTP compatible DHCP relay Access Control & Firewall (RT) Packet filtering based on Inbound/outbound direction Source/destination IP address Protocol types (ICMP, TCP, UDP) Port number range Up to 4 control lists QoS QoS based on rate limit Classification based on Outbound direction Source/destination IP addresses DSCP Protocol types Port number range Administration & Diagnostics Ping Traceroute Loopback Telnet SSH Electrical Power Source (AC) 100 to 240 Vac, 0.8A Power Source (DC) -36 to -72 Vdc, 1.2A Power Consumption < 20 W Physical and Environment Dimensions x 44 x 228 mm (W x H x D) Mounting Stand-alone, wall mount Temperature Range 0 C to 55 C Humidity 0% - 95% RH (non-condensing) Standards Compliance IEEE 802.1d bridge, 802.1w RSTP, 802.1q VLAN, 802.1ad Q-in-Q IETF RIP1 (RFC1058), RIP2 (RFC1389) ITU G.703, G.704, G.823 Compliance EMC/EMI Safety FCC15 Class A, EN55022, EN55024 UL60950, IEC (CB) FCC68, CS-03 4

5 Loop- Multiple WAN Router/Bridge Front Panel View Cold plug-in Slot A Cold plug- in Slot B Ground Screw USBPort* AC Power DC Power WAN1-2 LAN 1-4 LEDs ACO WAN Backup* Console Port * Future option Application Illustrations LAN E1/T1 LAN Multiple WANs E1/T1 MLPPP Bundle 5

6 Loop- Multiple WAN Router/Bridge Backup Ethernet DSL DSL Ethernet E1/T1 Ethernet as a backup link LOOP TELECOMMUNICATION INTERNATIONAL, INC. LoopTelecom.com ISO 9001 / ISO Worldwide Taipei, Taiwan North America Tianjin, China 8F, No. 8, Hsin Ann Road 6F, No. 36, Alley 38, Lane Carrick Road No. 240 Baidi Road Hsinchu Science Park Rueiguang Road Palm Beach Gardens Nankai District Hsinchu, Taiwan Neihu, Taiwan Florida 33418, U.S.A. Tianjin China michael_tzeng@loop.com.tw jimber561@aol.com wym@loop-tj.com sales@loop.com.tw 2013 Loop Telecommunication International, Inc. All Rights Reserved Version 5 1 April 2013 Subject to change without notice 6