SIP-WS 200V SIP-WS 210V. SIP Stations SIP-WS 200V / SIP-WS 210V. Datasheet

Transcription

1 Datasheet SIP-WS 200V SIP-WS 210V 1 2 SIP Stations Full Duplex capable, vandal resistant SIP stations designed for areas with high requirements on safety. The stations are connected directly to the Ethernet (LAN/ WAN) and in this manner are connected to a compatible SIP Server via the IP-network. The built-in switch with downlink function allows direct connection of an addi tional IP-device (e.g. an IP-camera). Besides high volume, the SIP stations provide a numerous amount of further features: Pre-recorded audio can be applied in a multi-purpose manner, e.g. as acoustic indication at line fault or as waiting information at call initiation, a configurable background noise canceller provides a crystal clear communication in challenging situations. Furthermore, the stations are perfectly suited for use as door stations at entry- and gateways, due to integrated relay outputs. The 3 mm stainless steel front panel with tamper protection and special screws protects against vandalism. The robust construction provides full protection against water, dirt and dust protection class IP 65. Each button can be allocated to a call number and the relevant label area can be filled in individually. The red emergency call button is easily visible from a consi derable distance and can be activated quickly in emergency situations. 1. SIP-WS 201V (not pictured) SIP station with one programmable, back-lit direct dialling button, electret microphone with multi function LED, loudspeakers 2 x 8 Ω, built-in amplifier class D 2.5 W, 2 relay outputs (connection as make or break contact), protection classifi cation IP 65 and IK 09, material stainless steel. 2. SIP-WS 211V (not pictured) SIP station with one programmable, back-lit emergency call button, electret microphone with multi function LED, loudspeakers 2 x 8 Ω, built-in amplifier class D 2.5 W, 2 relay outputs (connection as make or break contact), protection classifi cation IP 65 and IK 08, material stainless steel. SIP-WS 202V (not pictured) SIP station like SIP-WS 201V but with 2 programmable, back-lit direct dialling buttons. SIP-WS 212V SIP station like SIP-WS 211V but with an additional programmable, back-lit direct dialling button. SIP-WS 203V SIP station like SIP-WS 201V but with 3 programmable, back-lit direct dialling buttons. Datasheet Version 1.0/0711 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 1 16

2 Technical Data Benefits Technical data IP rating: IP 65 Mechanical impact resistance acc. EN 62262: SIP-WS 200V: IK 09 SIP-WS 210V: IK 08 Front panel: stainless steel, 3 mm (0.12 in) Operating temperature range: 20 C to 70 C ( 4 F to 158 F) Storage temperature range: 20 C to 70 C ( 4 F to 158 F) Relative humidity: up to 95% not condensing Call button: 1 3 direct dialling buttons only SIP-WS 210V: large red emergency call button Microphone: Omnidirectional electret microphone for max. 7 m (23 ft) speaking distance Loudspeaker: Special membrane type for optimal sound quality, sound pressure: 85 db/1 W/1 m (3.28 ft), 2 x 8 Ω Amplifier: Built-in amplifier class D with 2.5 W Status indication: red LED Outputs: 2 SPDT (changeover) relay outputs 30 V / 1 A: 100,000 make-and-break cycles RAM Memory: 32 MByte Flash Memory: 8 MByte DTMF Decoding: RFC 2833 SIP User Agent (UDP): RFC 3261 IP Protocol: IPv4, TCP, UDP, HTTP, RTP, RTCP DHCP, SNMPv2 Frequency range: 300-3,400 Hz Connection: pluggable screw terminals - IP Uplink/Downlink: shielded RJ 45 modular jacks Cabling: min. Cat. 5 Power supply: 24 VDC ± 2 V, 500mA or PoE Power consumption: 1.4 W idle approx. 1.7 W at conversation (depending on volume) PoE (Power over Ethernet): IEEE 802.3af standard Power consumption of the terminal device: Class 0 (0.44 W to W) Codecs: G.711 a-law G.711 μ-law prepared for G.722 Ethernet: 2 x 10/100 MBit/s (full/half Duplex) Additional mounting material: flush mount kit WSFB 50V flush mount kit WSFB 50V FL surface mount kit WSSH 50V rain protection roof WSRR 50V Measurements: with flush mount kit WSFB 50V: W 164 mm (6.46 in), H 279 mm (10.98 in), D 14 mm (0.55 in) with flush mount kit WSFB 50V FL: W 164 mm (6.46 in), H 279 mm (10.98 in), flush with plaster with surface mount kit WSSH 50V: W 164 mm (6.46 in), H 279 mm (10.98 in), D 50 mm (1.97 in) Weight incl. package: approx g (3.3 lbs) Benefits Vandal resistant IP rating IP 65 and mechanical impact resistance up to IK 09 Very high volume Full Duplex for natural, hands-free communication SNMP for surveillance of the station Using Pre-recorded audio as: Waiting information at call initiation Individual call tone for call initiation Location message Acoustic indication at line fault Control of the 2 relays e.g. as door opener via DTMF post-dial or Web Attendant contacts for various functions, e.g. Additional signalisation while ringing, during a call or in case of malfunction Operation without Server possible Configurable Acoustic Echo Canceller (AEC) Configurable Background Noise Canceller Adaptive jitter buffer Complies with SIP standard for easy integration in every SIP capable PBXes Integrated webserver for configuration & firmware update Adjustment of microphone sensitivity and volume Flexible operation via Power over Ethernet or via external power supply 3.4 khz speech quality for optimum intelligibility and compatibility Increased system availability by redundant LAN infrastructure The integrated data switch function enables the connection of further IP devices, e.g. IP camera Configurable Auto Answer Function Instant boot (system boot within seconds) Communication via IP-data networks no additional cabling required Configurable backlight System Requirements Compatible SIP Server (see page 5) or G8-VOIPSERV (for additional features) Extent of Supply SIP station Screws for mounting Series SIP-WS 210V: 3 x paste-on label ( SOS / EMERGENCY / HELP ) for emergency call button Short reference Datasheet Version 1.0/0711 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 2 16

3 * datasheet Typical Applications emergency systems at highways A typical application for use of SIP stations are emergency systems at highways. The SIP stations integrated in helppoints are connected to the appropriate SIP server and a call center over the IP network. A possible line fault is indicated acoustically via pre-recorded audio and can be processed by the SIP Server. Call Center Telephone * SIP 0 # * SIP 0 # Server IP NETWORK operation as door station Due to integrated relay outputs it is possible, to use the SIP stations as door stations (with door opener contacts) at entry- and gateways. The door opener contacts can be controlled by means of DTMF post-dialling or via web. Telephone SIP 0 # Server IP NETWORK Datasheet Version 1.0/0711 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 3 16

4 * datasheet Typical Applications In smaller Systems Due to the open standard of the SIP protocol, the stations can be operated without server. Therewith, cost-efficient use of the stations in smaller systems is enabled. Telephone SIP 0 # Datasheet Version 1.0/0711 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 4 16

5 Compatibility Compatibility SIP PBX Basically the SIP stations can be used with any SIP server. The following server types have been tested explicitly by Commend and therefore a proper functionality can be confirmed: manufacturer * Type version Digium Asterisk Version 1.2, 1.4, 1.6 Cisco Cisco Call Manager Cisco Unified Communication Manager Version 5 or higher Nortel CS1000 Version 6 Innovaphone Virtual Appliance IPVA Version 9 final Alcatel OmniPCX Enterprise OXE Siemens Hipath 4000 Version 5 3CX 3CX for Windows 3CX PhoneSystem 9 Starface Starface free Version Aastra MX-ONE Version 4.1 SP 1 * The listed products and company names are brand names or registered trademarks of their respective owners. Voip provider Type version Sipgate Sipgate.at, Sipgate.de December 2010 Vodafone Arcor Vodafone.de January 2011 bluesip bluesip.net May 2011 Datasheet Version 1.0/0711 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 5 16

6 Installation precautions When opening the stations ESD precautions must be observed. The stations may only be opened by authorised service engineers. connection Alternative power supply 24 V DC ± 2 V DC DC+ OUT 2 OUT 2 OUT 1 OUT 1 Slots for inserting button labels Factory Reset button IP Uplink + PoE IP Downlink (e.g. IP-camera) Attention: It is mandatory to ensure a correct power supply of the SIP station: min. 22 VDC, max. 26 VDC PoE has to be connected to the RJ 45 jack IP Uplink (see above). Further IP devices can be connected to the RJ 45 jack IP Downlink (see above), like e.g. an IP camera. But it is also possible to link up to 20 SIP-WS 2xxV in series via this ethernet interface. Attention Use of PoE: If multiple SIP-WS 2xxV are connected in series, then only the 1st device can be supplied with Power over Ethernet. All other devices (connected in series) must be supplied separately by an external power supply unit. configuration via webinterface Via the integrated webinterface, it is possible to configure optional direct dialling numbers for the buttons of the SIP WS 2xxV. Datasheet Version 1.0/0711 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 6 16

7 Installation measurements front panel Measurements in mm (inch), not to scale! Front panel thickness: 3 (0.12) 160 (6.3) 140 (5.5) 4x Ø 7 (0.28) 255 (10.05) 275 (10.84) Datasheet Version 1.0/0711 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 7 16

8 Installation Additional Mounting Material measurements Flush Mount box WSFB 50V Measurements in mm (inch), not to scale! MR... Flush mount frame (metal) with mounting frame (plastic) MR front flush with plaster MR Cutout for flush mount box: 137 (0.45) x 252 (0.83) 150 (5.91) (5.34) 4x Ø 7.5 (0.3) 15 (0.59) 197 (7.76) (9.87) 265 (10.44) 1 (0.04) (0.02) (1.79) 82 (3.23) 12x Expansion openings (can be broken out) Ø (0.59) 279 (10.99) 164 (6.46) 14 (0.55) MR extent of supply Flush mount box plastic (incl. cavity wall claws & cover lid) Mounting frame plastic (incl. mounting screws) Flush mount frame metal & gasket Cable fixing brackets (incl. screws) Short reference Weight incl. package: approx. 540 g (1.2 lbs) Datasheet Version 1.0/0711 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 8 16

9 Installation Additional Mounting Material mounting Flush mount box WSFB 50V To corresponding expansion opening of flush mount box of e.g. WS expansion module 1 gasket MOUNTING DIRECTION gasket 1 * Illustration front panel Connection spacer (with gaskets) for connecting two flush mount boxes and for cable feed through If possible, then 2 connection spacers shall be used per expansion (at deppened openings, see above)... Flush mount box (plastic)... Gasket For cavity wall mounting or installation in a desk, the cavity wall claws have to be used. (wall thickness: 5 mm to 30 mm / 0.19 in to 1.18 in)... Flush mount frame (metal)... Mounting frame (plastic) Screw mounting frame together with the flush mount frame (metal) and the gasket onto the flush mount box (screws in extent of supply)... Front panel (metal) with station electronics Screw front panel onto flush mount frame Datasheet Version 1.0/0711 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 9 16

10 Installation Additional Mounting Material measurements Flush Mount box WSFB 50V FL Measurements in mm (inch), not to scale! front flush with plaster 15 (0.59) (9.88) 279 (10.99) 22 (8.87) 53 (2.09) 164 (6.46) 136 (5.35) 12x Expansion openings (can be broken out) Ø 21 extent of supply Flush mount box plastic with mount frame metal (incl. cover lid) Cable fixing brackets (incl. screws) Short reference Weight incl. package: approx. 540 g (1.2 lbs) Datasheet Version 1.0/0711 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 10 16

11 Installation Additional Mounting Material mounting Flush mount box WSFB 50V FL...this side up, mounting direction * Illustration front panel Flush mount box (plastic) with Flush mount frame (metal) Install the flush mount box by moulding into plaster or concrete. Do not remove plaster cover until the flush mount box is mounted.... Front panel (metal) with electronics and gasket Screw front panel onto flush mount frame Datasheet Version 1.0/0711 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 11 16

12 Installation Additional Mounting Material measurements Surface Mount box WSSH 50V Measurements in mm (inch), not to scale! 164 (6.46) 148 (5.83) 229 (9.02) 218 (8.58) 200 (7.88) 279 (10.99) 4x Mounting openings Ø 6 (0.24) 4x Ø 5 (0.2) 50 (1.97) 114 (4.49) 60 (2.36) 6x Ø 22 (0.87) extent of supply Surface mount box metal (incl. 6 x dummy plugs) Plastic box 4 x IP 65 cable feed through 2 x sabotage plates (currently not applicable for SIP stations) Wall mount kit (screws, dowels, gasket rings and washers) Cable fixing brackets (incl. screws) Short reference Weight incl. package: approx. 945 g (2.08 lbs) Datasheet Version 1.0/0711 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 12 16

13 Installation Additional Mounting Material mounting Surface mount box WSSH 50V Attention: The dummy plugs for the surface mount box (in extent of supply) can not be removed without opening the housing! * Illustration front panel Snap in Surface mount box (Metal) Mounting via wall mounting kit (screws and dowels) in extent of supply... IP 65 cable feed through The cable feed through can be put into the plastic box after breaking out the expansion openings (installation cable feed through see picture to the right).... Plastic box Press the plastic box into the surface mount box... Front panel (metal) with station electronics Screw the front panel onto the surface mount box Insert cable Pull back tight Datasheet Version 1.0/0711 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 13 16

14 Installation Additional Mounting Material measurements Rain protection Roof WSRR 50V Measurements in mm (inch), not to scale! foam strip, approx. 2 mm (0.08 in) 164 (6.45) 80 (3.15) 277 (10.9) extent of supply Rain Protection Roof Fixing screws Short reference Weight incl. package: approx. 465 g (1.03 lbs) Datasheet Version 1.0/0711 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 14 16

15 Installation Additional Mounting Material mounting rain protection roof WSRR 50V Note: The rain protection roof can be used for vandal resistant SIP stations in surface mount version and in flush mount version. Following illustration shows the installation of the rain protection roof WSRR 50V to the surface mount kit WSSH 50V. Example: Surface mount kit WSSH 50V Front panel (metal) with station electronics Rain protection roof WSRR 50V Fixing screws required for WSRR 50V (in extent of supply) Remove the screws with which the station front panel is mounted Afterwards, screw the rain protection roof with the station front panel onto the surface mount box or the flush mount frame by using the fixing screws in the extent of supply (see above). Datasheet Version 1.0/0711 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 15 16

16 COMMEND A Strong Network Worldwide Europe America SWITZERLAND LIECHTENSTEIN Commend AG Tel USA CANADA LATIN AMERICA Commend Inc. Tel FRANCE Commend France S.A.S. Tel Asia SpAIN portugal Commend Ibérica S.L. Tel (Madrid) Tel (Barcelona) CHINA Commend Business Hub China Isolectra China Tel ITALY NETHERLANDS BELGIUM LUXEMBURG Commend Italia S.R.L. Tel Commend B.V. Tel SINGApORE Africa Commend Business Hub Asia Isolectra Far East pte. Ltd Tel AUSTRIA SLOVENIA RUSSIA CROATIA SERBIA BOSNIA-HERZEGOVINA Commend Österreich GmbH Tel Commend Adria d.o.o. Tel SOUTH AFRICA ALGERIA TUNISIA MOROCCO Commend Business Hub South Africa Evolving Management Solutions (pty) Ltd Tel Commend France S.A.S. Tel SLOVAKIA CZECH REpUBLIC Commend Slovakia spol. s r.o. Tel Middle East UNITED KINGDOM IRELAND Commend UK Ltd Tel ISRAEL Sberlophone Ltd Tel poland C&C Partners Telecom Sp.z o.o. Tel Oceania SWEDEN NORWAY FINLAND DENMARK ICELAND JNT Sound System AB Tel AUSTRALIA NEW ZEALAND Other countries Commend Australia Tel GERMANY Schneider Intercom GmbH Tel Commend International GmbH Tel Datasheet Version 1.0/0711 Errors and omissions excepted Products may change in the interest of technical improvements without notice. P 16 16