Optocoupler, Phototransistor Output, 4 Pin LSOP, Long Creepage Mini-Flat Package FEATURES A 4 C Low profile package High collector emitter voltage, V CEO = 8 V 7295-6 DESCRIPTION The has a GaAs infrared emitting diode emitter, which is optically coupled to a silicon planar phototransistor detector, and is incorporated in a 4 pin LSOP wide body package. It features a high current transfer ratio, low coupling capacitance, and high isolation voltage. The coupling device is designed for signal transmission between two electrically separated circuits. C 2 3 E Isolation test voltage, 5 V RMS Isolation voltage V IORM = 5 V peak Low coupling capacitance High common mode transient immunity Material categorization: for definitions of compliance please see www.vishay.com/doc?9992 APPLICATIONS Telecom Industrial controls Battery powered equipment Office machines Programmable controllers AGENCY APPROVALS (All parts are certified under base model ) UL577, file no. E76222 cul CSA 22.2 bulletin 5A, double protection DIN EN 6747-5-5 (VDE 884-5), available with option BSI: EN 665:22, EN 695-:26 FIMKO EN695- CQC: GB8898-2, GB4943.-2 ORDERING INFORMATION V O L 6 7 A - # X T LSOP-4 PART NUMBER CTR BIN PACKAGE OPTION TAPE AND REEL.2 mm AGENCY CERTIFIED/ PACKAGE UL, cul, BSI, FIMKO, CQC 4 pin LSOP, mini-flat, long creepage UL, cul, BSI, FIMKO, CQC, VDE (option ) 4 pin LSOP, mini-flat, long creepage CTR (%) 5 ma 5 to 6 4 to 8 63 to 25 to 2 6 to 32 8 to 6 3 to 26 T T 2T 3T 4T - - 5 to 6 4 to 8 63 to 25 to 2 6 to 32 8 to 6 3 to 26 XT XT 2XT 3XT 4XT 7XT 8XT Rev. 2., 3-Oct-5 Document Number: 82424 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
ABSOLUTE MAXIMUM RATINGS (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Reverse voltage V R 6 V Power dissipation P diss mw Forward surge current t p < μs I FSM.5 A Forward current I F 6 ma Junction temperature T j 25 C OUTPUT Collector emitter voltage V CEO 8 V Emitter collector voltage V ECO 7 V Collector current I C 5 ma t p /T =.5, t p < ms I C ma Power dissipation P diss 5 mw Junction temperature T j 25 C COUPLER Total power dissipation P tot 25 mw Storage temperature range T stg -55 to +25 C Ambient temperature range T amb -55 to + C Soldering temperature () s T sld 26 C Notes Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. () Refer to reflow profile for soldering conditions for surface mounted devices. P tot - Total Power Dissipation (mw) 3 25 2 5 5 Coupled device Phototransistor IR-diode 2 4 6 8 2 T amb - Ambient Temperature ( C) Fig. - Total Power Dissipation vs. Ambient Temperature ELECTRICAL CHARACTERISTICS (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT INPUT Forward voltage I F = 5 ma V F -.6.5 V Capacitance V R = V, f = MHz C O - 45 pf Reverse current V R = 6 V I R - μa OUTPUT Collector emitter leakage current V CE = V, I F = A I CEO - 2 na Collector emitter capacitance V CE = 5 V, f = MHz C CE - 7 - pf COUPLER Collector emitter saturation voltage I C =. ma, I F = 5 ma V CEsat -.25.4 V Coupling capacitance f = MHz C C -.25 - pf Note Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. Rev. 2., 3-Oct-5 2 Document Number: 82424 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
CURRENT TRANSFER RATIO (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT CTR 5-6 % CTR 4-8 % 2 CTR 63-25 % I C /I F I F = 5 ma, V CE = 5 V 3 CTR - 2 % 4 CTR 6-32 % 7 CTR 8-6 % 8 CTR 3-26 % SWITCHING CHARACTERISTICS (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Turn on time V CC = 5 V, I C = 2 ma, R L = Ω t on - 6 - μs Rise time V CC = 5 V, I C = 2 ma, R L = Ω t r - 3.5 - μs Turn off time V CC = 5 V, I C = 2 ma, R L = Ω t off - 5.5 - μs Fall time V CC = 5 V, I C = 2 ma, R L = Ω t f - 5 - μs V CC = 5 V Input pulse Input R L V OUT % 9 % Output pulse t r t f t on t off isfh68a_ Fig. 2 - Test Circuit isfh68a_2 Fig. 3 - Test Circuit and Waveforms SAFETY AND INSULATION RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Partial discharge test voltage - routine test %, t test = s V pd 2 kv Partial discharge test voltage - lot test (sample test) t Tr = 6 s, t test = s, (see figure 4) V IOTM 8 kv V pd.68 kv Maximum withstanding isolation voltage t = min V ISO 5 V RMS Insulation voltage V IORM 5 V peak V IO = 5 V DC, T amb = 25 C R IO 2 Ω Insulation resistance V IO = 5 V DC, T amb = C R IO Ω V IO = 5 V DC, T amb = 5 C (construction test only) R IO 9 Ω Safety rating - maximum input current I si 3 ma Safety rating - maximum power dissipation P SO 265 mw Rated impulse voltage V IOTM 8 kv Safety rating - maximum ambient temperature T si 5 C Comparative tracking index CTI 275 Clearance distance 8 mm Creepage distance 8 mm Insulation distance (internal) DTI.4 mm Note According to DIN EN 6747-5-5 (VDE 884-5), 7.4.3.8.2, (see figure 4). This optocoupler is suitable for safe electrical isolation only within the safety ratings. Compliance with the safety ratings shall be ensured by means of suitable protective circuits. Rev. 2., 3-Oct-5 3 Document Number: 82424 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
www.vishay.com 3 V IOTM 25 2 Phototransistor P SO (mw) t, t 2 = s to s t 3, t 4 = s t test = s t stres = 2 s V pd 5 V IOWM V IORM 5 IR-diode I si (ma) 25 5 75 25 T si - Safety Temperature ( C) 5 393 t t Tr = 6 s t 3 t test t 4 t 2 t stres t Fig. 4 - Derating Diagram Fig. 5 - Test Pulse Diagram for Sample Test according to DIN EN 6747-5-5 TYPICAL CHARACTERISTICS (T amb = 25 C, unless otherwise specified) I F - Forward Current (ma) T amb = C T amb = 75 C T amb = 25 C T amb = C T amb = - 55 C I CE - Leakage Current (na).. I F = ma V CE = 4 V V CE = 2 V V CE = 24 V..6.8..2.4.6 V F - Forward Voltage (V). -6-4 -2 2 4 6 8 2 T amb - Ambient Temperature ( C) Fig. 6 - Forward Current vs. Forward Voltage Fig. 8 - Collector Emitter Current vs. Ambient Temperature I C - Collector Current (ma) 55 5 45 4 35 3 25 2 5 5 I F = 35 ma I F = 3 ma I F = 25 ma I F = 2 ma I F = 5 ma I I F = ma F = ma I F = 5 ma 2 3 4 5 6 7 8 9 I C - Collector Current (ma) 3 25 2 5 5 I F = 25 ma I F = ma I F = 5 ma I F = ma I F = 2 ma..2.3.4 V CE - Collector Emitter Voltage (V) V CE - Collector Emitter Voltage (V) Fig. 7 - Collector Current vs. Collector Emitter Voltage Fig. 9 - Collector Current vs. Collector Emitter Voltage Rev. 2., 3-Oct-5 4 Document Number: 82424 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
N CTR - Normalized CTR (non-saturated).2..8.6.4 I F = 5 ma.2 Normalized to CTR value: I F = 5 ma, V CE = 5 V, T amb = 25 C -6-4 -2 2 4 6 8 2 T amb - Ambient Temperature ( C) N CTR - Normalized CTR (sat).2..8.6.4.2 V CE =.4 V Normalized to: I F = 5 ma, V CE = 5 V, T amb = 25 C T amb = C T amb = -55 C T amb = 25 C T amb = 75 C T amb = C. I F - Forward Current (ma) Fig. - Normalized Current Transfer Ratio (non-saturated) vs. Ambient Temperature Fig. 3 - Normalized Current Transfer Ratio (saturated) vs. Forward Current N CTR - Normalized CTR (sat).2..8.6.4.2 Normalized to CTR value: I F = 5 ma, V CE = 5 V, T amb = 25 C -6-4 -2 2 4 6 8 2 Phase Angle (deg) -2-4 -6-8 - -2-4 -6 V CE = 5 V R L = Ω R L = Ω T amb - Ambient Temperature ( C) f - Frequency (khz) Fig. - Normalized Current Transfer Ratio (saturated) vs. Ambient Temperature Fig. 4 - Cut-Off Frequency vs. Phase Angle N CTR - Normalized CTR (NS).4.2..8.6.4.2 T amb = -55 C T amb = 25 C T amb = C T amb = 75 C T amb = C Normalized to: I F = 5 ma, V CE = 5 V. I F - Forward Current (ma) f CTR (khz) V CC = 5 V. I C (ma) Fig. 2 - Normalized Current Transfer Ratio (non-saturated) vs. Forward Current Fig. 5 - Cut-Off Frequency vs. Collector Current Rev. 2., 3-Oct-5 5 Document Number: 82424 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
t on, toff - Switching Time (μs) V CE = 5 V, I F = 2 ma t off (μs) t on (μs). 5 5 2 R L - Load Resistance (kω) Fig. 6 - Switching Time vs. Load Resistance. V CEsat - Collector Emitter Saturation Voltage (V).8.6.4 CTR = 5 % used 2 % used.2 % used 95 28 I C - Collector Current (ma) Fig. 7 - Collector Emitter Saturation Voltage vs. Collector Current t on /t off - Turn-On/Turn-Off Time (µs) 5 4 3 2 Saturated operation V S = 5 V R L = kω 5 5 95 3 I F - Forward Current (ma) t off t on 2 Fig. 8 - Turn-On/Turn-Off Time vs. Forward Current Rev. 2., 3-Oct-5 6 Document Number: 82424 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
PACKAGE DIMENSIONS (in millimeters) 2.3 max. 2. 4. max. 3.8. +.3 -.4.2 7.5 ±.2.2 + -..5 Seating plane.45 ±..7 +.3 -.4 2.54 nom. 4 3 Possible footprint.9 2.54 8.2.8 22533 2 Pin no. identification technical drawings according to DIN specifications PACKAGE MARKING (example of 3XT) 67A-3X V YWW 68 Notes Only option is reflected in the package marking with the characters X. Tape and reel suffix (T) is not part of the package marking. TAPE AND REEL DIMENSIONS (in millimeters) ESD sticker.75 Ø.55 2 4 2.7.3 33 (3") Tape slot in core 6.6 7.5 5 4.25 8 Regular, special or bar code label 7999 Direction of pulling out Ø.6 technical drawings according to DIN specification 2.3 22662 Fig. 9 - Reel Dimensions (3 units per reel) Fig. 2 - Tape Dimensions Rev. 2., 3-Oct-5 7 Document Number: 82424 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
SOLDER PROFILE Temperature ( C) 3 25 2 5 255 C 24 C 27 C max. 2 s max. 26 C 245 C max. 3 s max. s max. ramp down 6 C/s HANDLING AND STORAGE CONDITIONS ESD level: HBM class 2 Floor life: unlimited Conditions: T amb < 3 C, RH < 85 % Moisture sensitivity level, according to J-STD-2 5 max. ramp up 3 C/s 984 5 5 2 25 3 Time (s) Fig. 2 - Lead (Pb)-free Reflow Solder Profile according to J-STD-2 Rev. 2., 3-Oct-5 8 Document Number: 82424 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Revision: 3-Jun-6 Document Number: 9