RA 23 351/9.99 RA 23 351/9.99 Replces: 6.98, 8.9 4/3-, 4/2- nd 3/2- directionl vlves with switching time djustment, Model 5-.WE 1 (5-chmer version) Nominl size 1 Series 3X Mximum operting pressure 4569 PSI (315 r) Mximum flow 31.7 GPM (12 L/min) HA 596/98 Model 5-.WE 1 E3X/CG24N9K4 with plug-in connector Contents Description Pge Fetures 1 Ordering code 2, 3 Symols 3 Functionl description, section 4, 5 Technicl dt 6 Chrcteristic curves 7 Performnce limits 7 Unit dimensions 8 Aville spre prts nd sels 9 Fetures Direct solenoid operted spool type directionl control vlve With 5 th chmer for dmpened djustle spool shifting time Mounts on stndrd ISO 441-5, NFPA/ANSI T3.5.1 M R1 D 5, ANSI B 93.7 D 5 interfce For supltes, see dt sheet RA 45 54 Wet pin DC solenoids (AC possile with rectifier) Removle coils for quick replcement, or conversion, in AC or DC voltges Individul solenoid plug-in connectors, or centrl wiring ox to NEMA 4 specifictions (see dt sheet RA 8 2) Optionl mnul overrides 53 stndrd spool configurtions ville Importnt! The length of the mounting olt in series 3X/... is 1-1/2" (4 mm) [formerly 2" ( 5 mm)] 1/1
RA 23 351/9.99 Ordering code 1 2 3 4 6 7 9 1 11 12 15 18 19 22 23 5 WE 1 3X C * 3 ctutor ports = 3 4 ctutor ports = 4 Nominl size 1 = 1 Symol e.g. C, E, EA, EB etc. for possile versions, see pge 3 Series 3 to 39 = 3X (3 to 39: unchnged instlltion nd connection dimensions) With spring return = No code Without spring return with detent = OF Without spring return = O Wet pin solenoid (oil immersed) with removle coil = C 12 V DC = G12 24 V DC = G24 96 V DC = G96 1) For further ordering detils regrding other voltges nd frequencies, see pge 6. With protected mnul override (stndrd) = N9 Without hnd override = No code Hnd override with protective cp = N Model of electricl connection Individul connection; with component plug = K4 2) DIN 43 65-AM2, without plug-in connector Without switching time djustment = No code With djustle screw (throttle) = C Orifice Ø.236 in (.6 mm) = A6 Orifice Ø.276 in (.7 mm) = A7 Orifice Ø.315 in (.8 mm) = A8 Without crtridge throttle = No code Throttle Ø.315 in (.8 mm) = B8 Throttle Ø.394 in (1. mm) = B1 Throttle Ø.472 in (1.2 mm) = B12 Throttle Ø.591 in (1.5 mm) Used for flows > performnce limits of = B15 Throttle Ø.118 in (3. mm) the vlve, effective in the P chnnel = B3 NBR sels = No code FKM sels = V (other sels on request) Attention! The comptiility of the sels nd pressure fluid hs to e tken into ccount! Further detils in cler text AC supply (permissile voltge tolernce ± 1%) Nominl voltge of the DC solenoid when used with n AC voltge Order code 11 V - 5/6 Hz 96 V G96 12 V - 6 Hz 11 V G11 23 V - 5/6 Hz 25 V G25 1) For the connection to n AC supply DC solenoid must e used which is controlled vi rectifier (see tle on the left). For individul connections lrge plug-in connector with integrted recifier cn e used (seprte order, see pge 3). 2) Plug-in connectors must e ordered seprtely (see pge 3). Attention! The performnce limits on pge 7 must e tken into ccount! Rexroth Hydrulics 2/1 5-.WE 1
Ordering code, plug-in connectors to DIN 43 65 A nd ISO 44 for component plug "K4" RA 23 351/9.99 For further plug-in connectors see RA 8 6 Vlve side Color Without circuitry With indictor light 12 24 V Mteril no. With indictor light nd With LED & rectifier With rectifier Z diode protective circuit 24 24 V 12 24 V 24 V Thred grey RR 74683 Pg 11 lck RR 74684 Pg 11 / lck RR 57292 RR 57423 RR 313933 RR 31995 Pg 11 red/rown RR 4823 1/2 NPT lck RR 1139 1/2 NPT / lck RR 57453 RR 57455 RR 842566 1/2 NPT Symols /O.. =.A 1) 1) Exmple: Spool E with switched position Ordering detil..ea.. /OF.. A B =.B P T P T = A = E 1) = P = C = F = Q = D = G = R = H = T = B = J = U = Y = L = V = M = W 5-.WE 1 3/1 Rexroth Hydrulics
RA 23 351/9.99 Functionl description, section 5-chmer directionl vlves of model 5-.WE re solenoid operted directionl spool vlves. They control the strt, stop nd direction of flow with the dditionl option of djusting the spool switching time. These directionl vlves siclly consist of housing (1), one or two solenoids (2), control spool (3), s well s one or two return springs (4). Two spring chmers re connected y drilling (5). As the spool switches, the flow is displced from one spring chmer to the other vi this pssge. If the re of this connecting ore is reduced y n orifice, the switching time chnges ccordingly. The T chnnels re isolted from the spring chmers. Switching pulses do not ffect control spool (3) nd thus, soft switching of the spool cn e chieved. In the de-energized condition, control spool (3) is held in the centrl or initil position y return springs (4) (except for impulse spools). The control spool (3) is ctuted y wet pin solenoids (2). In order to ensure correct functioning, cre must e tken to ensure tht the pressure chmer of the solenoid is filled with oil. The force of solenoid (2) cts on control spool (3) nd switches it from its rest position to the required end position. This then permits flow from P to A nd B to T or P to B nd A to T. When solenoid (2) is de-energized the control spool (3) is returned to its rest position y return spring (4). A mnul override (6), optionl, enles the control spool (3) to e moved without energiztion of the solenoids. Adjustle spool switching time (only with DC solenoids) The optionl instlltion of throttle screw (7) or orifice (8) - see elow - offers the possiility of incresing switching time with throttle screw model 5-.WE 1../..CG../C.. (7) with orifice model 5-.WE 1../..CG../A.. (8) 2 7 1 3 5 2 A B "" "" 4 TA T P B TB 4 6 Model 5-4WE 1 E3X/CG24N9K4/C.. With the instlltion of orifices, spool switching time my e lengthened y more thn 1 ms. The ctul time is dependent upon individul system prmeters (e.g. pressure, flow nd viscosity). When reto-fitting or modifying throttling system, cre must e tken tht the fluid volume in the spring chmers nd the connecting ore (5) is retined, s this is prerequisite for the smooth opertion of the switching time djustment. 5 8 5 Without throttle screw/ without orifice Model 5-.WE 1../..CG../.. With orifice Model 5-.WE 1../..CG../A.. Rexroth Hydrulics 4/1 5-.WE 1
Functionl description, section Model 5-.WE 1.3X/OC... (only possile with symols A, C nd D) This version is directionl vlve with 2 switched positions nd 2 solenoids without detent. There is no defined spool position in the deenergized condition. Model 5-.WE 1.3X/OFC... (impulse spool), with detent (only possile with symols A, C nd D) This version is directionl vlve with 2 detented switched positions nd 2 solenoids. Thus, the spool is held in the lst switched position, permnent energiztion of the solenoid is not required. RA 23 351/9.99 With throttle olt Model 5-.WE 1../..CG../C.. A "" TA Detent Model 5-.WE 1 E3X/OFC (impulse spool) Throttle insert (model 5-.WE 1.3X/.../B..) The use of throttle insert is required if, due to the operting conditions, flows cn occur during the switching process which re lrger thn the performnce limits of the vlve llow. The orifice is to e inserted into the P chnnel of the directionl vlve. P O-ring.472 in x.79 in (12 mm x 2 mm) 5-.WE 1 5/1 Rexroth Hydrulics
RA 23 351/9.99 Technicl dt (for pplictions outside these prmeters, plese consult us!) Generl Instlltion optionl Mx. mient temperture F ( C) 122 (5) Weight Vlve with 1 solenoid ls (kg) 1.4 (4.7) Hydrulic dt Vlve with 2 solenoids ls (kg) 13.9 (6.3) Mx. operting pressure Ports A, B, P PSI (r) 4569 (315) Port T PSI (r) 346 (21) with symols A nd B, port T must e used s drin port, if the operting pressure is higher thn the permissile tnk pressure. Mx. flow GPM (L/min) 31.7 (12) Flow cross-section For symol V in 2 (mm 2 ).171 (11) (A/B T);.16 (1.3) (P A/B) (switched position ) For symol W in 2 (mm 2 ).39 (2.5) (A/B T) For symol Q in 2 (mm 2 ).85 (5.5) (A/B T) Pressure fluid Minerl oil (HL, HLP) to DIN 51 524 1) ; Fst io-degrdle pressure fluids to VDMA 24 568 (lso see RA 9 221); HETG (rpe seed oil) 1) ; HEPG (Polyglycols) 2) ; HEES (synthetic ester) 2) ; other pressure fluids on request Pressure fluid temperture rnge F ( C) 22 to +176 ( 3 to +8) (with NBR sels) 4 to +176 ( 2 to +8) (with FPM sels) Viscosity rnge SUS (mm 2 /s) 35 to 2318 (2.8 to 5) Degree of contmintion Mximum permissile degree of contmintion of the pressure fluid is to NAS 1638 clss 9. We, therefore, recommend filter with minimum retention rte of ß 1 75. Electricl dt Model of voltge Aville voltges 3) V 12, 24, 42, 6, 96, 11, 18, 25, 23 Voltge tolernce (nominl voltge) % ±1 Power consumption W 35 Duty DC continuous Switching time to ISO 643 ON ms 45 to 7 (without switching time djustment) OFF ms 35 to 45 Switching frequency cycles/h 15 Protection to DIN 4 5 IP 65 Insultion clss VDE 58 Mx. coil temperture 4) F ( C) 32 (15) 1) suitle for NBR nd FPM sels F 2) only suitle for FPM sels 3) specil voltges on request 4) Due to the surfce tempertures which occur on the solenoid coils, the Europen stndrds EN563 nd EN982 must e tken into ccount! When connecting the electrics, the protective conductor (PE ) must e connected ccording to the relevnt regultions. Rexroth Hydrulics 6/1 5-.WE 1
Chrcteristic curves, mesured t ν = 19 SUS (41 mm 2 /s) nd t = 122 F (5 C) Pressure differentil in PSI (r) (16) (15) (14) (13) (12) (11) (1) (9) (8) (7) (6) (5) (4) (3) (2) (1) (315) (3) (25) (2) (15) (1) (5) (315) (3) (25) (2) (15) (1) (5) 232 218 23 189 174 16 145 131 116 12 87 72.5 58 43.5 29 14.5 4569 4351 3626 291 2176 145 725 4569 4351 3626 291 2176 145 725 p-q V -chrcteristic curves 2.64 5.28 7.93 1.6 13.2 15.9 18.5 21.1 23.8 26.4 29.1 31.7 (1) (2) (3) (4) (5) (6) (7) (8) (9) (1) (11) (12) Flow in GPM (L/min) Performnce limits: DC, mesured t ν = 19 SUS (41 mm 2 /s) nd t = 122 F (5 C) Becuse of silting, the shifting function of the vlves is dependent upon filtrtion. To otin the mximum flow vlues shown, full filtrtion of 25 µm is recommended. The flow forces cting within the vlve lso influence performnce. In 4-wy vlves, the dt provided is for pplictions with 2 directions of flow (flow from P to A nd n equl, simultneous return from B to T), (see tle). Operting pressure in PSI (r) Operting pressure in PSI (r) 4 5 12 1 2.64 5.28 7.93 1.6 13.2 15.9 18.5 21.1 23.8 26.4 29.1 31.7 (1) (2) (3) (4) (5) (6) (7) (8) (9) (1) (11) (12) Flow in GPM (L/min) 8 11 9 2.64 5.28 7.93 1.6 13.2 15.9 18.5 21.1 23.8 26.4 29.1 31.7 (1) (2) (3) (4) (5) (6) (7) (8) (9) (1) (11) (12) Flow in GPM (L/min) 7 12 RA 23 351/9.99 5-.WE 1 7/1 Rexroth Hydrulics 9 2 3 6 1 1 9 8 7 6 5 4 3 1 2 Symols Direction of flow P A P B A T B T A, B 1 1 C 1 3 1 3 D, Y 2 2 1 3 E 2 2 3 4 F 2 1 4 7 G 4 4 6 8 H 2 2 1 3 J, L 1 1 4 4 M 2 2 3 4 P 2 1 1 7 Q, V 1 1 3 4 R 1 4 3 T 4 4 5 7 U 1 1 3 3 W 1 1 3 5 Switch. pos. B A R 9 Centr. pos. B T A T P T F 4 4 G, T 8 P 8 6 If only one direction of flow is required, for exmple, when 4-wy vlve hs one port plugged, or with unlnced flows from lrge rod cylinders, the permissile flow in criticl cses cn e considerly lower. The A or B spool (3-wy) cn e used s n pproximtion of the limited flow performnce. Performnce limits mesured with solenoids t operting temperture, 1% undervoltge nd without tnk port pressure. Chr. curve Symols With orifice Ø.236 in (.6 mm) ( A6 ) 3 D, Y 12 C With nd without orifice 1 C/O, C/OF, D/O, D/OF, M 2 A/O, A/OF, E, J, L, U, Q, W 4 G 5 F, P 1 H Chr. curve Symols Without orifice 1 D, Y 6 C 7 R 8 T 9 V 11 A, B
RA 23 351/9.99 Unit dimensions: dimensions in inches (millimeters) 17.4/4. in 11 3.63 (92.2).1/1 mm 2.13 (54).752 (19.1) 32 (R mx 4) 2.76 (7) 1.81 (46) TA P TB Required surfce finish of interfce when mounting the vlvewithout our suplte.591 (15) 1 5 Pg 11 8 4 16 15 13 4 9 1 A Ø.433 (11) B 6 4.61 (117) 3.62 (92) 4.84 (123).591 (15).236 (6) 1.58 (4) 1.18 (3) 12.29 (5.3) 2.95 (75) Ø.26 (6.6) 1.2 (26) 3.15 (8) 4.97 (126.3) 7.1 (18.3).29 (5.3) 8.12 (26.3) 8.12 (26.3) 2.95 (75) 12.7 (36.6) 14 13 7 2 1 3 7 1 3-position vlve 1) 2 2-position vlve with 1 solenoid (A, C, D, EA...) 1) 3 2-position vlve with 1 solenoid (B, Y, EB...) 1) 4 Plug for vlve with 1 solenoid 5 Solenoid "" (plug-in connector colour grey) 6 Solenoid "" (plug-in connector colour lck) 7 Spce required to remove the coil 8 Plug-in connector without circuitry to DIN 43 65 2) (Z4, Z45) 9 Plug-in connector with circuitry to DIN 43 65 2) (Z5, Z55) 1 Spce required to remove plug-in connector 11 Mnul override N9 (stndrd) Actution of the mnul override is only possile up to mx. tnk pressure of 725 PSI (5 r) Avoid dmge to the mnul override pin ore! 12 Dim. for mnul override N 13 Nme plte 14 R-ring.512 in x.63 in x.79 in (13 mm x 1.6 mm x 2 mm (for vlve with throttle insert: O-ring.472 in x.79 in (12 mm x 2 mm) 15 Additionl T port (TB) my optionlly e used in conjunction with drilled locks. 16 Porting pttern to ISO 441-5, NFPA T3.5.1M R1 nd ANSI B 93.7 D 5 Supltes G 66/5 (3/8" NPT); G 66/12 (SAE-6; 9/16-18); G 67/5 (1/2" NPT); G 646/12 (SAE-1; 7/8-14); G 534/5 (3/4" NPT); G 534/12 (SAE-12; 1-1/16-12) 17 Vlve Mounting Bolts 4) 1/4-2 UNC x 1-1/2" (M6 x 4 mm) socket hed cp screws (SAE grde 8 or etter) Tightening torque 11.4 l-ft (15.5 Nm) Suplte nd vlve mounting olts must e ordered seprtely, see RA 45 54 1) Dimension without mnul override nd with protected mnul override N9 2) must e ordered seprtely, see pge 3. Rexroth Hydrulics 8/1 5-.WE 1
Ordering code, ville spre prts nd sels RA 23 351/9.99 113 113 16 113 157 Spre prts solenoid Item Designtion Voltge Mteril no. 12 V RR 19792 157 Coil for individul connection 24 V RR 19793 RR 874529 16 Sel kit nut for pressure tue without mnul override nd pressure tue with protected mnul override Sel kit nut for pressure tue with mnul override RR 874528 Sel kit vlve Item Seling mteril Mteril no. 113 NBR sels RR 312582 FPM sels RR 312583 5-.WE 1 9/1 Rexroth Hydrulics
RA 23 351/9.99 Notes Mnnesmnn Rexroth Corportion Rexroth Hydrulics Div., Industril, 2315 City Line Rod, Bethlehem, PA 1817-2131 Tel. (61) 694-83 Fx: (61) 694-8467 Rexroth Hydrulics Div., Moile, 17 Old Mnsfield Rod, Wooster, OH 44691-394 Tel. (33) 263-34 Fx: (33) 263-3333 All rights reserved Suject to revision Printed in U.S.A. 1/1 5-.WE 1