Upflow/ Horizontal Left, Downflow/ Horizontal Right Speed Two Stage Condensing Gas-Fired Furnace XV 95 TUH2B060A9V3VB TUH2B080A9V3VB TUH2B080A9V4VB TUH2C100A9V4VB TUH2C100A9V5VB TUH2D120A9V5VB Direct Vent with Speed Blower Speed Inducer TDH2B060A9V3VB TDH2B080A9V3VB TDH2B080A9V4VB TDH2C100A9V4VB TDH2D120A9V5VB *UH-A9V-V *DH-A9V-V DOWNF UPF UPF/HORIZONTAL DOWNF/HORIZONTAL PUB. NO. 22-1814-11
General Features NATURAL GAS MODELS Central Heating furnace designs are certified by the American Gas Association for both natural and L.P. gas. Limit setting and rating data were established and approved under standard rating conditions using American National Standards Institute standards. SAFE OPERATION The Integrated System Control has solid state devices, which continuously monitor for presence of flame, when the system is in the heating mode of operation. Dual solenoid combination gas valve and regulator provide additional safety. QUICK Durable, cycle tested, heavy gauge aluminized steel heat exchanger quickly transfers heat to provide warm conditioned air to the structure. Low energy power vent blower, to increase efficiency and provide a positive discharge of gas fumes to the outside. BURNERS Multiport Inshot burners will give years of quiet and efficient service. All models can be converted to L.P. gas without changing burners. INTEGRATED SYSTEM CONTROL Exclusively designed operational program provides total control of furnace limit sensors, blowers, gas valve, flame control and includes self diagnostics for ease of service. Also contains connection points for E.A.C./Humidifier. ENERGY EFFICIENT OPERATION Furnace is certified to leak 2% or less of nominal air conditioning delivered when pressurized to.5 water column with all inlets, outlets, and drains sealed. AIR DELIVERY The variable speed blower motor has sufficient airflow for most heating and cooling requirements and will switch from heating to cooling speeds on demand from room thermostat. The blower door safety switch will prevent or terminate furnace operation when the blower door is removed. SECONDARY HEAT EXCHANGER The XV95 has a special type 29-4C stainless steel secondary heat exchanger to reclaim heat from flue gases which would normally be lost instead. STYLING Heavy gauge steel and wraparound cabinet construction is used in the cabinet with baked-on enamel finish for strength and beauty. The heat exchanger section of the cabinet is completely lined with foil faced fiberglass insulation. This results in quiet and efficient operation due to the excellent acoustical and insulating qualities of fiberglass. Built-in bottom pan and alternate bottom, left or right side return air connection provision. FEATURES AND GENERAL OPERATION The XV95 High Efficiency Gas Furnaces utilize an Adaptive Heat Up Silicon Nitride Hot Surface Ignition system, which eliminates the waste of a constant burning pilot. The integrated system control lights the main burners upon a demand for heat from the room thermostat. Complete front service access. a. Low energy power venter b. Vent proving pressure switch. 2013 Trane All Rights Reserved 2
Contents General Features 2 Features and Benefits 4 Standard Equipment 4 Optional Equipment 5 General Data 6-8 TUH2B060A9V3VB TUH2B080A9V3VB TUH2B080A9V4VB TUH2C100A9V4VB TUH2C100A9V5VB TUH2D120A9V5VB TDH2B060A9V3VB TDH2B080A9V3VB TDH2B080A9V4VB TDH2C100A9V4VB TDH2D120A9V5VB Performance Data 9-19 Venting Table 20 Electrical Data 21-24 Field Wiring 25-26 Dimensions 27-28 3
Features and Benefits XV 95 STANDARD EQUIPMENT Speed Blower Motor Silicon Nitride Igniter with adaptive heat up speed induced draft blower Direct/Non-Direct vent option Fused 24 volt control circuit Manual reset burner safety switches Power supply Convertible to horizontal on left side 2-stage gas valve PVC venting-1 or 2 pipe option Accessory hook-up capability Integrated solid state control with selfdiagnostics Attractive color accents Heavy gauge aluminized steel heat exchanger Multi-port In-shot burners Quiet induced draft blower Lite Port extended system diagnostics Stored fault code history in micro processor nonvocatile memory Cleanable high velocity filters (upflow only) Hinged blower door * Perfect fit door latches* Insulated blower door* Gasketed blower door* Complete front service access Left/right gas connection Adjustable fan off times Optional L.P conversion kit Selectable cooling fan off delay eliminates need for BAY24X045 time delay kit * (Upflow only) 4
Features and Benefits XV 95 OPTIONAL EQUIPMENT Thermostat, 2-Stage Heat / 1-Stage Cooling... TAYSTAT241 [ ] Thermostat, Media Programmable 2-Stage Heating...TAYSTAT302C [ ] Thermostat, Mechanical Heating Only With Fan Switch...TAYSTAT303C [ ] Thermostat, Heating/Cooling Single Stage (Mounts Horizontally)...AY28X092 [ ] Thermostat, Heating/Cooling Single Stage (Mounts Vertically)...BAYSTAT305 [ ] Thermostat, Media Programmable 1-Stage Heating/1-Stage Cooling...TAYSTAT300C [ ] Propane Conversion Kit... BAYLPKT210A [ ] Media Air Filter, Perfect Fit High Efficiency (14-1/2" Wide Gas Furnace)... TFM145A9FR0 [ ] Media Air Filter, Perfect Fit High Efficiency (17-1/2" Wide Gas Furnace)... TFM175A9FR0 [ ] Media Air Filter, Perfect Fit High Efficiency (21" Wide Gas Furnace)... TFM210A9FR0 [ ] Media Air Filter, Perfect Fit High Efficiency (24-1/2" Wide Gas Furnace)... TFM245A9FR0 [ ] Media Air Filter, Perfect Fit Standard Efficiency (14-1/2" Wide Gas Furnace)...TFP145A9FR0 [ ] Media Air Filter, Perfect Fit Standard Efficiency (17-1/2" Wide Gas Furnace)...TFP175A9FR0 [ ] Media Air Filter, Perfect Fit Standard Efficiency (21" Wide Gas Furnace)...TFP210A9FR0 [ ] Media Air Filter, Perfect Fit Standard Efficiency (24-1/2" Wide Gas Furnace)...TFP245A9FR0 [ ] Coil Enclosure (14-1/2" Wide Cabinets)... BAYCLE14A1422A [ ] Coil Enclosure (17-1/2" Wide Cabinets)... BAYCLE17A1722A [ ] Coil Enclosure (21" Wide Cabinets)... BAYCLE21A2130A [ ] Coil Enclosure (24-1/2" Wide Cabinets)... BAYCLE24A2430A [ ] Downflow Subbase... BAYBASE205 [ ] Side Filter Rack... BAYFLTR200 [ ] Filter Kit/Horizontal Conversion TUH2-060,080... BAYFLTR203 [ ] Filter Kit/Horizontal Conversion TUH2-100... BAYFLTR204 [ ] Filter Kit/Horizontal Conversion TUH2-120... BAYFLTR205 [ ] High Altitude Pressure Switch Kit TUH2-060... BAYSWT10AHALTA1 [ ] High Altitude Pressure Switch Kit TUH2-080,100,120... BAYSWT08AHALTA1 [ ] Concentric Vent Kit TUH2 Furnaces...BAYAIR30AVENTA [ ] Sidewall Vent Termination Kit All 2 Pipe Direct Vent Furnaces...BAYVENT200B [ ] Manufactured/Mobile Home Kit All 2 Pipe Direct Vent Furnaces...BAYMFGH100A [ ] Cleanable Filter (14.5"/17.5" wide Upflow models)... BAYFLTR317 [ ] Cleanable Filter (21" wide Upflow models)... BAYFLTR321 [ ] Cleanable Filter (24.5" wide Upflow models)... BAYFLTR324 [ ] CleanEffects, Whole House Air Cleaner (Upflow 14-1/2" Wide Gas Furnace)... TFD145ALFR000B [ ] CleanEffects, Whole House Air Cleaner (Upflow 17-1/2" Wide Gas Furnace)...TFD175ALFR000B [ ] CleanEffects, Whole House Air Cleaner (Upflow 21" Wide Gas Furnace)...TFD210ALFR000B [ ] CleanEffects, Whole House Air Cleaner (Upflow 24-1/2" Wide Gas Furnace)...TFD245ALFR000B [ ] CleanEffects, Whole House Air Cleaner (Downflow 14-1/2" Wide Gas Furnace)... TFD14DALFR000B [ ] CleanEffects, Whole House Air Cleaner (Downflow 17-1/2" Wide Gas Furnace)... TFD17DALFR000B [ ] CleanEffects, Whole House Air Cleaner (Downflow 21" Wide Gas Furnace)... TFD21DALFR000B [ ] CleanEffects, Whole House Air Cleaner (Downflow 24-1/2" Wide Gas Furnace)... TFD24DALFR000B [ ] CleanEffects, Whole House Transformer Kit (120 to 24 Volt - all TFD Air Cleaners)... BAYTRANS12024 [ ] 1 Optional kit allows 200 ft. max. vent length from 5,000-12,000 feet above sea level. See installer's guide. 5
General Data MODEL TYPE RATINGS 2 1st Stage Input BTUH 1st Stage Capacity BTUH (ICS) 3 2nd Stage Input BTUH 2nd Stage Capacity BTUH (ICS) 3 AFUE Temp. rise (Min.-Max.) F. BER DRIVE Diameter - Width (In.) No. Used Speeds (No.) vs. in. w.g. Motor HP R.P.M. Volts / Ph / Hz FLA COMBUSTION FAN - Type Drive - No. Speeds Motor HP - RPM Volts / Ph / Hz FLA FILTER Furnished? Type Recommended Hi Vel. (No.-Size-Thk.) VENT Size (in.) HEAT EXCHANGER Type -Fired -Unfired Gauge (Fired) ORIFICES Main Nat. Gas. Qty. Drill Size L.P. Gas Qty. Drill Size GAS VALVE PILOT SAFETY DEVICE Type BURNERS Type Number POWER CONN. V / Ph / Hz 4 Ampacity (In Amps) Max. Overcurrent Protection (Amps) PIPE CONN. SIZE (IN.) DIMENSIONS Crated (In.) WEIGHT Shipping (Lbs.) / Net (Lbs) TUH2B060A9V3VB 5 Upflow / Horizontal 39,000 37,830 60,000,200 97 35-65 DIRECT 10 x 8 1 See Fan Performance Table 1/2 7.7 Centrifugal Direct - 1/ - 00 33-110/3/60-180 1.0 Yes High Velocity 1-17x25-1 in. 2 Round Aluminized Steel - Type I 20 3 45 3 Redundant - Two Stage Hot Surface Igniter Multiport Inshot 3 10.8 15 1/2 H x W x D 41-3/4 x 19-1/2 x 30-1/2 1 / 146 TUH2 PRODUCT SPECIFICATIONS1 Product Specifications 1 TUH2B080A9V3VB 5 Upflow / Horizontal 52,000,0 80,000 77, 97 35-65 DIRECT 10 x 8 1 See Fan Performance Table 1/2 7.7 Centrifugal Direct - 1/ - 00 33-110/3/60-180 1.0 Yes High Velocity 1-17x25-1 in. 2 Round Aluminized Steel - Type I 20 4 45 4 Redundant - Two Stage Hot Surface Igniter Multiport Inshot 4 10.8 15 1/2 H x W x D 41-3/4 x 19-1/2 x 30-1/2 168 / 1 TUH2B080A9V4VB 5 Upflow / Horizontal 52,000,0 80,000 77, 97 35-65 DIRECT 11 x 8 1 See Fan Performance Table 3/4 9.6 Centrifugal Direct - 1/ - 00 33-110/3/60-180 1.0 Yes High Velocity 1-17x25-1 in. 2 Round Aluminized Steel - Type I 20 4 45 4 Redundant - Two Stage Hot Surface Igniter Multiport Inshot 4 13.2 15 1/2 H x W x D 41-3/4 x 19-1/2 x 30-1/2 170 / 1 TUH2C100A9V4VB 5 Upflow / Horizontal 65,000 62,855 100,000 96, 96.7 35-65 DIRECT 10 x 10 1 See Fan Performance Table 3/4 9.6 Centrifugal Direct - 1/ - 00 33-110/3/60-180 1.0 Yes High Velocity 1-20x25-1 in. 3 Round Aluminized Steel - Type I 20 5 45 5 Redundant - Two Stage Hot Surface Igniter Multiport Inshot 5 13.2 15 1/2 H x W x D 41-3/4 x 23 x 30-1/2 197 / 185 1 Central Furnace heating designs are certified to ANSI Z21.47 / CSA 2.3 2 For U.S. applications, above input ratings (BTUH) are up to 2,000 feet, derate 4% per 1,000 feet for elevations above 2,000 feet above sea level. For Canadian applicaitons, above input ratings (BTUH) are up to 4,0 feet, derate 4% per 1,000 feet for elevations above 4,0 feet above sea level. 3 Based on U.S. government standard tests. 4 The above wiring specifications are in accordance with National Electrical Code; however, installations must comply with local codes. 5 Energy Star 6
General Data MODEL TYPE RATINGS 2 1st Stage Input BTUH 1st Stage Capacity BTUH (ICS) 3 2nd Stage Input BTUH 2nd Stage Capacity BTUH (ICS) 3 AFUE Temp. rise (Min.-Max.) F. BER DRIVE Diameter - Width (In.) No. Used Speeds (No.) vs. in. w.g. Motor HP R.P.M. Volts / Ph / Hz FLA COMBUSTION FAN - Type Drive - No. Speeds Motor HP - RPM Volts / Ph / Hz FLA FILTER Furnished? Type Recommended Hi Vel. (No.-Size-Thk.) VENT Size (in.) HEAT EXCHANGER Type -Fired -Unfired Gauge (Fired) ORIFICES Main Nat. Gas. Qty. Drill Size L.P. Gas Qty. Drill Size GAS VALVE PILOT SAFETY DEVICE Type BURNERS Type Number POWER CONN. V / Ph / Hz 4 Ampacity (In Amps) Max. Overcurrent Protection (Amps) PIPE CONN. SIZE (IN.) DIMENSIONS Crated (In.) WEIGHT Shipping (Lbs.) / Net (Lbs) TUH2/TDH2 PRODUCT SPECIFICATIONS1 TUH2C100A9V5VB 5 Upflow / Horizontal 65,000 62,855 100,000 96, 96.7 35-65 DIRECT 11 x 10 1 See Fan Performance Table 1 12.8 Centrifugal Direct - 1/ - 00 33-110/3/60-180 1.0 Yes High Velocity 1-20x25-1 in. 3 Round Aluminized Steel - Type I 20 5 45 5 Redundant - Two Stage Hot Surface Igniter Multiport Inshot 5 17.2 20 1/2 H x W x D 41-3/4 x 23 x 30-1/2 199 / 187 PRODUCT SPECIFICATIONS 1 TUH2D120A9V5VB 5 Upflow / Horizontal 78,000 75,426 120,000 116,040 96.7 40-70 DIRECT 10 x 10 1 See Fan Performance Table 1 12.8 Centrifugal Direct - 1/ - 00 33-110/3/60-180 1.0 Yes High Velocity 1-24x25-1 in. 3 Round Aluminized Steel - Type I 20 6 45 6 Redundant - Two Stage Hot Surface Igniter Multiport Inshot 6 17.2 20 1/2 H x W x D 41-3/4 x 26-1/2 x 30-1/2 206 / 193 TDH2B060A9V3VB 5 Downflow / Horizontal 39,000 37,000 60,000,000 96 35-65 DIRECT 10 x 8 1 See Fan Performance Table 1/2 7.7 Centrifugal Direct - 1/ - 00 33-110/3/60-180 1.0 Yes High Velocity 2-14x20-1 in. 2 Round Aluminized Steel - Type I 20 3 45 3 Redundant - Two Stage Hot Surface Igniter Multiport Inshot 3 10.8 15 1/2 H x W x D 41-3/4 x 19-1/2 x 30-1/2 160/ 146 TDH2B080A9V3VB 5 Downflow / Horizontal 52,000,400 80,000 76,000 96 35-65 DIRECT 10 x 8 1 See Fan Performance Table 1/2 7.7 Centrifugal Direct - 1/ - 00 33-110/3/60-180 1.0 Yes High Velocity 2-14x20-1 in. 2 Round Aluminized Steel - Type I 20 4 45 4 Redundant - Two Stage Hot Surface Igniter Multiport Inshot 4 10.8 15 1/2 H x W x D 41-3/4 x 19-1/2 x 30-1/2 168 / 1 1 Central Furnace heating designs are certified to ANSI Z21.47 / CSA 2.3 2 For U.S. applications, above input ratings (BTUH) are up to 2,000 feet, derate 4% per 1,000 feet for elevations above 2,000 feet above sea level. For Canadian applicaitons, above input ratings (BTUH) are up to 4,0 feet, derate 4% per 1,000 feet for elevations above 4,0 feet above sea level. 3 Based on U.S. government standard tests. 4 The above wiring specifications are in accordance with National Electrical Code; however, installations must comply with local codes. 5 Energy Star 7
General Data TDH2 PRODUCT SPECIFICATIONS1 MODEL TYPE RATINGS 2 1st Stage Input BTUH 1st Stage Capacity BTUH (ICS) 3 2nd Stage Input BTUH 2nd Stage Capacity BTUH (ICS) 3 AFUE Temp. rise (Min.-Max.) F. BER DRIVE Diameter - Width (In.) No. Used Speeds (No.) vs. in. w.g. Motor HP R.P.M. Volts / Ph / Hz FLA COMBUSTION FAN - Type Drive - No. Speeds Motor HP - RPM Volts / Ph / Hz FLA FILTER Furnished? Type Recommended Hi Vel. (No.-Size-Thk.) VENT Size (in.) HEAT EXCHANGER Type -Fired -Unfired Gauge (Fired) ORIFICES Main Nat. Gas. Qty. Drill Size L.P. Gas Qty. Drill Size GAS VALVE PILOT SAFETY DEVICE Type BURNERS Type Number POWER CONN. V / Ph / Hz 4 Ampacity (In Amps) Max. Overcurrent Protection (Amps) PIPE CONN. SIZE (IN.) DIMENSIONS Crated (In.) WEIGHT Shipping (Lbs.) / Net (Lbs) PRODUCT SPECIFICATIONS 1 TDH2B080A9V4VB 5 Downflow / Horizontal 52,000,400 80,000 76,000 95 35-65 DIRECT 11 x 8 1 See Fan Performance Table 3/4 9.6 Centrifugal Direct - 1/ - 00 33-110/3/60-180 1.0 Yes High Velocity 2-14x20-1 in. 2 Round Aluminized Steel - Type I 20 4 45 4 Redundant - Two Stage Hot Surface Igniter Multiport Inshot 4 13.2 15 1/2 H x W x D 41-3/4 x 19-1/2 x 30-1/2 172 / 160 TDH2C100A9V4VB 5 Downflow / Horizontal 65,000 61,7 100,000 95,000 96 35-65 DIRECT 10 x 10 1 See Fan Performance Table 3/4 9.6 Centrifugal Direct - 1/ - 00 33-110/3/60-180 1.0 Yes High Velocity 2-16x20-1 in. 3 Round Aluminized Steel - Type I 20 5 45 5 Redundant - Two Stage Hot Surface Igniter Multiport Inshot 5 13.2 15 1/2 H x W x D 41-3/4 x 23 x 30-1/2 185 / 175 TDH2D120A9V5VB5 Downflow / Horizontal 78,000 74,000 120,000 114,000 96 40-70 DIRECT 10 x 10 1 See Fan Performance Table 1 12.8 Centrifugal Direct - 1/ - 00 33-110/3/60-180 1.0 Yes High Velocity 2-16x20-1 in. 3 Round Aluminized Steel - Type I 20 6 45 6 Redundant - Two Stage Hot Surface Igniter Multiport Inshot 6 17.2 20 1/2 H x W x D 41-3/4 x 26-1/2 x 30-1/2 206 / 196 1 Central Furnace heating designs are certified to ANSI Z21.47 / CSA 2.3 2 For U.S. applications, above input ratings (BTUH) are up to 2,000 feet, derate 4% per 1,000 feet for elevations above 2,000 feet above sea level. For Canadian applicaitons, above input ratings (BTUH) are up to 4,0 feet, derate 4% per 1,000 feet for elevations above 4,0 feet above sea level. 3 Based on U.S. government standard tests. 4 The above wiring specifications are in accordance with National Electrical Code; however, installations must comply with local codes. 5 Energy Star 8
*UH2B060A9V3V FURNACE AIRF () AND POWER () VS. WITH FILTER 1ST 2ND AIRF 1st Stage Capacity = 2nd Stage Capacity = 37,830,200 SW 7 SW 8 0.1 0.3 0.5 0.7 0.9 ON ON MEDIUM OFF ON ** ON OFF OFF OFF ON ON MEDIUM OFF ON ** ON OFF NOTES: * First letter may be "A" or "T" ** Factory setting OFF OFF 85 90 775 105 870 39 135 860 61 140 53 190 1125 47 2 12 42 340 110 130 775 155 870 39 185 920 200 53 255 1125 47 315 12 42 405 155 175 775 195 870 39 235 920 245 53 305 1125 47 370 12 42 5 190 210 775 240 870 39 290 920 300 53 340 1025 51 355 1100 390 - - - - 670 79 245 75 255 775 68 285 53 355 *UH2B060A9V3V FURNACE COOLING AIRF () AND POWER () VS. WITH FILTER OUTDOOR UNIT SIZE (TONS) AIRF SW 1 SW 2 SW 3 SW 4 0.1 0.3 0.5 0.7 0.9 (3 /TON) ON ON OFF ON 5 65 5 90 5 125 5 155-1.5 (400 /TON) ON ON OFF OFF 640 70 640 110 640 140 630 175 - (4 /TON) ON ON ON OFF 85 125 160 200 - (3 /TON) OFF ON OFF ON 100 130 170 210-2.0 (400 /TON) OFF ON OFF OFF 115 155 200 2 - (4 /TON) OFF ON ON OFF 140 195 240 290 - (3 /TON) ON OFF OFF ON 875 130 875 180 875 230 875 270-2.5 (400 /TON) ON OFF OFF OFF 175 235 285 335 (4 /TON) ON OFF ON OFF 1125 235 1125 295 1125 345 1100 370 925 318 (3 /TON) OFF OFF OFF ON 10 195 10 260 10 305 10 3 920 315 3 (400 /TON) OFF OFF OFF OFF 275 330 385 1100 385 940 330 (4 /TON) OFF OFF ON OFF 1325 360 1325 425 1300 460 1175 425 365 NOTES: * First letter may be "A" or "T" 1. At continuous fan setting: Heating or Cooling airflows are approximately % of selected cooling value. 2. airflow (3 cfm/ton) is COMFORT & HUMID CLIMATE setting; airflow (400 cfm/ton) is typical setting; airflow (4 cfm/ton) is DRY CLIMATE setting. 9
*UH2B080A9V3V FURNACE AIRF () AND POWER () VS. WITH FILTER 1ST AIRF 1st Stage Capacity = 2nd Stage Capacity =,0 77, SW 7 SW 8 0.1 0.3 0.5 0.7 0.9 ON ON MEDIUM OFF ON ** ON OFF 105 860 52 115 960 46 1 140 880 51 165 990 45 200 180 890 215 230 220 920 265 1020 265 910 320 1010 3 2ND OFF OFF ON ON MEDIUM OFF ON ** ON OFF NOTES: * First letter may be "A" or "T" ** Factory setting OFF OFF 1080 41 195 1100 62 205 1210 265 1360 365 1360 355 1110 40 255 1100 62 260 1240 55 340 1390 5 1390 4 1120 40 315 1120 61 320 1260 54 410 0 520 1120 40 365 1120 61 370 1260 54 470 1360 535 13 51 535 1080 41 390 1090 63 400 1130 61 430 1210 475 1180 465 *UH2B080A9V3V FURNACE COOLING AIRF () AND POWER () VS. WITH FILTER OUTDOOR UNIT SIZE (TONS) AIRF SW 1 SW 2 SW 3 SW 4 0.1 0.3 0.5 0.7 0.9 2.0 2.5 3.0 3.5 (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) ON ON OFF ON ON ON OFF OFF ON ON ON OFF OFF ON OFF ON OFF ON OFF OFF OFF ON ON OFF ON OFF OFF ON ON OFF OFF OFF ON OFF ON OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF ON OFF 7 84 840 109 940 136 8 113 960 1 1080 195 1020 175 1170 240 1290 1170 2 1360 365 1360 355 NOTES: * First letter may be "A" or "T" 1. At continuous fan setting: Heating or Cooling airflows are approximately % of selected cooling value. 2. airflow (3 cfm/ton) is COMFORT & HUMID CLIMATE setting; airflow (400 cfm/ton) is typical setting; airflow (4 cfm/ton) is DRY CLIMATE setting. 7 122 840 146 940 177 8 1 990 200 1110 255 1020 225 1180 300 1320 410 1190 315 1390 5 1390 4 7 154 840 181 940 215 870 200 230 1120 315 1040 280 365 13 470 1210 370 0 520 720 185 840 226 940 274 890 2 1020 305 1120 365 10 330 415 1340 520 1210 435 1360 535 13 535 710 221 820 264 940 318 890 295 1010 3 1080 390 10 375 1130 420 11 0 1100 405 1210 475 1180 460 10
*UH2B080A9V4V FURNACE AIRF () AND POWER () VS. WITH FILTER 1ST 2ND AIRF 1st Stage Capacity = 2nd Stage Capacity =,0 77, SW 7 SW 8 0.1 0.3 0.5 0.7 0.9 ON ON MEDIUM OFF ON ** ON OFF OFF OFF ON ON MEDIUM OFF ON ** ON OFF OFF OFF NOTES: * First letter may be "A" or "T" ** Factory setting 105 860 52 115 960 46 1 1080 41 195 1100 62 205 1210 265 1360 365 1360 355 140 880 51 165 990 45 200 1110 40 255 1100 62 260 1240 55 340 1390 5 1390 4 180 890 215 230 1120 40 315 1120 61 320 1260 54 410 0 520 220 920 265 1020 1120 40 365 1120 61 370 1260 54 470 1360 535 13 51 535 265 910 320 1010 3 1080 41 390 1090 63 400 1130 61 430 1210 475 1180 465 *UH2B080A9V4V FURNACE COOLING AIRF () AND POWER () VS. WITH FILTER OUTDOOR UNIT SIZE (TONS) AIRF SW 1 SW 2 SW 3 SW 4 0.1 0.3 0.5 0.7 0.9 (3 /TON) ON ON OFF ON 8 107 8 143 841 179 833 223 825 266 2.5 (400 /TON) ON ON OFF OFF 970 1 971 205 973 251 966 298 960 345 (4 /TON) ON ON ON OFF 1082 209 1093 266 1104 323 1099 374 1095 424 (3 /TON) OFF ON OFF ON 1004 153 1019 210 1035 267 1038 321 1041 374 3.0 (400 /TON) OFF ON OFF OFF 1163 2 1173 311 1184 372 1179 426 1174 0 (4 /TON) OFF ON ON OFF 1323 345 1328 411 1332 477 1320 532 1307 6 (3 /TON) ON OFF OFF ON 1176 254 1188 317 1195 437 1190 4 3.5 (400 /TON) ON OFF OFF OFF 13 379 1362 6 1368 514 1353 8 1339 623 (4 /TON) ON OFF ON OFF 1536 3 1536 5 1536 647 1512 699 18 751 (3 /TON) OFF OFF OFF ON 1376 374 1367 429 1359 3 1354 547 13 611 4.0 (400 /TON) OFF OFF OFF OFF 12 530 12 604 13 677 1531 720 19 765 (4 /TON) OFF OFF ON OFF 1768 7 1759 830 17 902 1654 866 1559 829 NOTES: * First letter may be "A" or "T" 1. At continuous fan setting: Heating or Cooling airflows are approximately % of selected cooling value. 2. airflow (3 cfm/ton) is COMFORT & HUMID CLIMATE setting; airflow (400 cfm/ton) is typical setting; airflow (4 cfm/ton) is DRY CLIMATE setting. 11
*UH2C100A9V4V FURNACE AIRF () AND POWER () VS. WITH FILTER 1ST 2ND AIRF 1st Stage Capacity = 2nd Stage Capacity = 62,855 96, SW 7 SW8 0.1 0.3 0.5 0.7 0.9 ON ON MEDIUM OFF ON MEDIUM ** ON OFF OFF OFF ON ON MEDIUM OFF ON MEDIUM ** ON OFF NOTES: * First letter may be "A" or "T" ** Factory setting OFF OFF 873 64 100 971 115 1136 160 12 225 1260 68 213 1464 59 315 1631 53 4 1846 47 640 893 63 145 997 170 1146 230 1298 43 300 1304 66 305 1471 59 405 1678 51 0 1867 46 760 62 195 1006 220 1165 295 1319 42 390 1329 65 1478 5 1690 51 670 1794 770 899 62 240 1022 55 280 1180 47 365 1328 42 4 1334 65 460 1478 0 19 55 645 16 52 902 62 290 1029 54 335 1184 47 425 1286 0 1317 65 510 13 64 540 1419 61 5 18 6 *UH2C100A9V4V FURNACE COOLING AIRF () AND POWER () VS. WITH FILTER OUTDOOR UNIT SIZE (TONS) AIRF SW 1 SW 2 SW 3 SW 4 0.1 0.3 0.5 0.7 0.9 2.5 3.0 3.5 4.0 (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) ON ON OFF ON ON ON OFF OFF ON ON ON OFF OFF ON OFF ON OFF ON OFF OFF OFF ON ON OFF ON OFF OFF ON ON OFF OFF OFF ON OFF ON OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF ON OFF NOTES: *First letter may be "A" or "T" 1. At Continuous fan setting: Heating or Cooling airflows are approximately % of selected cooling value. 2. airflow (3 cfm/ton) is COMFORT & HUMID CLIMATE setting; airflow (400 cfm/ton) is typical setting; airflow (4 cfm/ton) is DRY CLIMATE setting. 808 75 938 100 10 1 1004 120 1141 170 1336 2 1153 180 1390 285 15 400 1388 290 1610 415 1847 630 824 125 963 160 1100 200 1010 175 1190 245 1375 330 1206 2 1418 465 1606 5 1423 360 1641 515 1863 735 840 170 959 205 1121 265 1027 230 1214 1387 410 1230 320 1439 5 1632 590 14 0 1666 635 1816 780 835 210 964 255 1136 330 10 285 1229 1388 0 1239 395 11 515 1596 645 14 515 1607 6 1687 720 830 2 975 1142 395 10 345 1234 4 1384 545 12 460 1373 540 15 590 1390 540 14 595 1532 665 12
*UH2C100A9V5V FURNACE AIRF () AND POWER () VS. WITH FILTER 1ST 2ND AIRF NOTES: * First letter may be "A" or "T" ** Factory setting 1st Stage Capacity = 2nd Stage Capacity = 62,855 96, SW 7 SW 8 0.1 0.3 0.5 0.7 0.9 ON ON MEDIUM OFF ON MEDIUM ** ON OFF OFF OFF ON ON MEDIUM OFF ON MEDIUM ** ON OFF OFF OFF 873 64 100 971 115 1136 160 12 225 1260 68 213 1464 59 315 1631 53 4 1846 47 640 893 63 145 997 170 1146 230 1298 43 300 1304 66 305 1471 59 405 1678 51 0 1867 46 760 62 195 1006 220 1165 295 1319 42 390 1329 65 1478 5 1690 51 670 1794 770 899 62 240 1022 55 280 1180 47 365 1328 42 4 1334 65 460 1478 0 19 55 645 16 52 902 62 290 1029 54 335 1184 47 425 1286 0 1317 65 510 13 64 540 1419 61 5 18 6 *UH2C100A9V5V FURNACE COOLING AIRF () AND POWER () VS. WITH FILTER OUTDOOR UNIT SIZE (TONS) AIRF SW 1 SW 2 SW 3 SW 4 0.1 0.3 0.5 0.7 0.9 (3 /TON) OFF ON OFF ON 1163 222 1201 304 1209 375 433 1199 5 3.5 (400 /TON) OFF ON OFF OFF 1339 331 1365 400 1366 477 1377 555 1382 636 (4 /TON) OFF ON ON OFF 1515 0 1538 535 15 620 1553 708 1547 796 (3 /TON) ON OFF OFF ON 1339 331 1365 400 1366 477 1377 555 1382 636 4.0 (400 /TON) ON OFF OFF OFF 15 471 12 5 14 645 15 733 14 813 (4 /TON) ON OFF ON OFF 17 626 17 736 1770 838 1772 935 1760 1018 (3 /TON) OFF OFF OFF ON 1695 8 1709 728 1721 820 1772 930 1711 1007 5.0 (400 /TON) OFF OFF OFF OFF 1919 862 1919 9 1905 1043 1831 1043 1709 982 (4 /TON) OFF OFF ON OFF NA NA NA NA NA NA NA NA NA NA NOTES: *First letter may be "A" or "T" 1. At Continuous fan setting: Heating or Cooling airflows are approximately % of selected cooling value. 2. airflow (3 cfm/ton) is COMFORT & HUMID CLIMATE setting; airflow (400 cfm/ton) is typical setting; airflow (4 cfm/ton) is DRY CLIMATE setting. 3. NA = Not allowed. 13
*UH2D120A9V5V FURNACE AIRF () AND POWER () VS. WITH FILTER 1ST 2ND AIRF NOTES: * First letter may be "A" or "T" ** Factory setting 1st Stage Capacity = 2nd Stage Capacity = 75,426 116,040 SW 7 SW 8 0.1 0.3 0.5 0.7 0.9 ON ON MEDIUM OFF ON ** ON OFF OFF OFF ON ON MEDIUM OFF ON ** ON OFF OFF OFF 1090 62 165 1210 220 1340 295 1430 47 390 1660 63 5 1870 675 2060 51 880 2200 1030 1120 60 225 280 1360 3 10 43 0 1690 62 590 1870 745 1990 53 890 2090 965 1080 63 270 330 1370 425 10 43 5 1680 62 640 1810 770 18 810 1940 54 895 1070 63 1180 395 1 5 10 43 625 1640 64 675 1680 62 715 1710 61 7 1790 830 1010 67 1160 455 1330 51 535 1390 5 1460 72 10 70 625 1530 68 665 1640 64 7 *UH2D120A9V5V FURNACE COOLING AIRF () AND POWER () VS. WITH FILTER OUTDOOR UNIT SIZE (TONS) 3.5 4.0 5 AIRF (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) SW 1 SW 2 SW 3 SW 4 0.1 0.3 0.5 0.7 0.9 OFF ON OFF ON OFF ON OFF OFF OFF ON ON OFF ON OFF OFF ON ON OFF OFF OFF ON OFF ON OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF ON OFF NOTES: * First letter may be "A" or "T" 1. At continuous fan setting: Heating or Cooling airflows are approximately % of selected cooling value. 2. airflow (3 cfm/ton) is COMFORT & HUMID CLIMATE setting; airflow (400 cfm/ton) is typical setting; airflow (4 cfm/ton) is DRY CLIMATE setting. 1210 220 305 1590 425 1390 305 1620 420 1840 1 0 20 845 2160 995 1210 270 10 390 1 520 375 16 530 1830 690 1780 630 2010 875 2040 935 1220 325 14 465 1610 1430 5 1670 595 1820 765 1780 705 1860 805 1920 875 1230 400 14 510 1 645 10 515 1640 660 1670 1 695 1710 735 1780 805 1230 5 1410 0 1 5 1420 5 10 10 620 1530 615 1530 655 1620 730 14
*DH2B060A9V3V FURNACE AIRF () AND POWER () VS. WITH FILTER 1ST 2ND AIRF NOTES: * First letter may be "A" or "T" ** Factory setting 1st CAPACITY = 2nd CAPACITY = 37,0, SW 7 SW 8 0.1 0.3 0.5 0.7 0.9 ON ON MEDIUM OFF ON ** ON OFF OFF OFF ON ON MEDIUM OFF ON ** ON OFF OFF OFF *DH2B060A9V3V FURNACE COOLING AIRF () AND POWER () VS. WITH FILTER OUTDOOR UNIT SIZE (TONS) 1.5 2.0 2.5 3 AIRF (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) 55 675 65 7 45 85 8 40 115 125 52 170 1100 47 215 1300 40 330 85 675 105 7 45 125 8 40 155 165 10 230 11 45 285 1325 39 385 120 675 140 7 45 160 8 40 205 220 10 295 11 45 340 1325 39 455 1 675 175 7 45 210 8 40 260 270 10 335 11 45 395 12 42 465 185 675 205 7 45 260 8 40 320 315 10 370 1100 47 0 43 470 SW 1 SW 2 SW 3 SW 4 0.1 0.3 0.5 0.7 0.9 OFF OFF OFF ON OFF OFF OFF OFF OFF OFF ON OFF ON ON OFF ON ON ON OFF OFF ON ON ON OFF OFF ON OFF ON OFF ON OFF OFF OFF ON ON OFF ON OFF OFF ON ON OFF OFF OFF ON OFF ON OFF NOTES: * First letter may be "A" or "T" 1. At continuous fan setting: Heating or Cooling airflows are approximately % of selected cooling value. 2. airflow (3 cfm/ton) is COMFORT & HUMID CLIMATE setting; airflow (400 cfm/ton) is typical setting; airflow (4 cfm/ton) is DRY CLIMATE setting. 525 45 55 675 65 70 100 125 875 115 1 1125 215 10 175 240 13 330 525 70 85 675 105 115 135 165 875 160 207 1125 285 10 240 315 13 410 525 100 120 625 140 145 175 220 875 210 265 1125 340 10 305 385 13 0 525 135 1 675 175 185 225 270 875 260 320 1125 395 10 345 0 1275 5 525 160 185 675 205 220 280 330 875 1125 0 10 1100 410 1170 4 15
*DH2B080A9V3V FURNACE AIRF () AND POWER () VS. WITH FILTER AIRF 1st CAPACITY = 2nd CAPACITY =,920 76, SW 7 SW 8 0.1 0.3 0.5 0.7 0.9 ON ON 130 170 210 790 245-1ST MEDIUM OFF ON ** ON OFF 162 205 210 265 260 295 345-295 OFF OFF 1170 38 305 1170 38 3 1170 38 400 1020 360 830 54 ON ON 11 60 285 11 60 345 11 60 385 1020 67*** 360 830 83*** 305 2ND MEDIUM OFF ON ** ON OFF 1275 54 1430 515 1275 54 5 1340 51 0 425 1220 455 1040 66*** 1090 63 410 76*** 3 930 74*** OFF OFF 1430 515 1340 51 0 1220 455 1090 63 410 930 74*** NOTES: * - First letter may be "A" or "T" ** Factory setting *** Above MAX Temperature change value *DH2B080A9V3V - FURNACE COOLING AIRF () AND POWER () VS. WITH FILTER OUTDOOR UNIT SIZE (TONS) 2.0 2.5 3.0 AIRF (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) SW 1 SW 2 SW 3 SW 4 0.1 0.3 0.5 0.7 0.9 ON ON OFF ON ON ON OFF OFF ON ON ON OFF OFF ON OFF ON OFF ON OFF OFF OFF ON ON OFF ON OFF OFF ON ON OFF OFF OFF ON OFF ON OFF NOTES: * First letter may be "A" or "T" 1. At continuous fan setting: Heating or Cooling airflows are approximately % of selected cooling value. 2. airflow (3 cfm/ton) is COMFORT & HUMID CLIMATE setting; airflow (400 cfm/ton) is typical setting; airflow (4 cfm/ton) is DRY CLIMATE setting. 95 130 160 875 145 205 11 295 10 235 335 13 455 105 160 215 875 185 265 11 340 10 295 385 13 0 115 205 255 875 240 11 385 10 340 410 1210 435 680 200 790 245 300 875 280 340 1020 3 1010 3 1040 365 1070 390 670 235 740 265 7 270 760 270 295 300 290 840 345 16
*DH2B080A9V4V FURNACE AIRF () AND POWER () VS. WITH FILTER 1ST 2ND AIRF 1st CAPACITY = 2nd CAPACITY =,400 76,000 SW 7 SW 8 0.1 0.3 0.5 0.7 0.9 ON ON MEDIUM OFF ON MEDIUM ** ON OFF OFF OFF ON ON MEDIUM OFF ON MEDIUM ** ON OFF OFF OFF NOTES: * - First letter may be "A" or "T" ** Factory setting *** Above MAX Temperature change value 130 162 205 1170 38 305 11 60 285 1275 54 1430 515 1430 515 170 210 265 1170 38 3 11 60 345 1275 54 5 1340 51 0 1340 51 0 210 260 1170 38 400 11 60 385 425 1220 455 1220 455 790 245 295 345 1020 360 1020 67*** 360 1040 66*** 1090 63 410 1090 63 410 - - 295 830 54 830 83*** 305 76*** 3 930 74*** 930 74*** *DH2B080A9V4V - FURNACE COOLING AIRF () AND POWER () VS. WITH FILTER OUTDOOR UNIT SIZE (TONS) 2.5 3.0 3.5 4.0 AIRF (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) SW 1 SW 2 SW 3 SW 4 0.1 0.3 0.5 0.7 0.9 ON ON OFF ON ON ON OFF OFF ON ON ON OFF OFF ON OFF ON OFF ON OFF OFF OFF ON ON OFF ON OFF OFF ON ON OFF OFF OFF ON OFF ON OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF ON OFF NOTES: * First letter may be "A" or "T" 1. At continuous fan setting: Heating or Cooling airflows are approximately % of selected cooling value. 2. airflow (3 cfm/ton) is COMFORT & HUMID CLIMATE setting; airflow (400 cfm/ton) is typical setting; airflow (4 cfm/ton) is DRY CLIMATE setting. 8 141 953 195 10 2 999 188 11 300 1288 412 11 307 1327 6 16 634 1327 6 1525 6 1706 906 865 191 965 2 1065 309 1003 241 11 362 1297 2 1165 374 1335 518 12 703 1335 518 1522 727 1635 881 881 241 977 305 1073 369 1008 394 11 423 1305 552 1174 0 1343 9 18 771 1343 9 1518 797 13 8 878 294 973 3 1069 422 1018 354 1160 6 1303 617 1177 2 1325 641 1418 746 1325 641 1430 761 1471 813 876 3 970 411 1064 474 1029 414 1165 5 1300 682 1179 3 1307 693 1338 721 1307 693 1341 725 1379 769 17
*DH2C100A9V4V - FURNACE AIRF () AND POWER () VS. WITH FILTER 1st CAPACITY = 62,400 2nd CAPACITY = 96,000 1ST 2ND AIRF SW 7 SW 8 0.1 0.3 0.5 0.7 0.9 ON ON MEDIUM OFF ON MEDIUM ** ON OFF OFF OFF ON ON MEDIUM OFF ON MEDIUM ** ON OFF OFF OFF NOTES: * - First letter may be "A" or "T" ** Factory setting *** Above MAX temperature change 923 61 110 1020 55 145 11 185 1275 225 1298 66 235 1439 60 1639 53 430 1790 18 0 955 59 165 1047 53 190 1166 240 1305 43 290 1320 65 305 1459 59 390 16 52 525 1818 47 670 960 210 1053 53 2 1172 300 1328 42 365 1335 65 12 470 16 52 1813 47 770 9 265 1042 54 295 1177 3 1328 42 5 1343 64 5 13 5 16 52 680 1708 7 947 59 1029 54 3 1178 420 1328 42 510 1343 64 520 1470 59 610 16 640 1535 675 *DH2C100A9V4V - FURNACE COOLING AIRF () AND POWER () VS. WITH FILTER OUTDOOR UNIT SIZE (TONS) 2.5 3.0 3.5 AIRF (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) 4.0 (3 /TON) (400 /TON) (4 /TON) SW 1 SW 2 SW 3 SW 4 0.1 0.3 0.5 0.7 0.9 ON ON OFF ON ON ON OFF OFF ON ON ON OFF OFF ON OFF ON OFF ON OFF OFF OFF ON ON OFF ON OFF OFF ON ON OFF OFF OFF ON OFF ON OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF ON OFF NOTES: * - First letter may be "A" or "T" 1. At continuous fan setting: Heating or Cooling airflows are approximately % of selected cooling value. 2. airflow (3 cfm/ton) is COMFORT & HUMID CLIMATE setting; airflow (400 cfm/ton) is typical setting; airflow (4 cfm/ton) is DRY CLIMATE setting. 870 100 989 120 1124 175 1053 145 1186 195 1336 255 1216 190 1394 270 19 395 1377 270 1599 425 1801 0 885 140 1018 180 1139 225 1075 200 1205 255 1366 340 1225 255 1422 360 1604 475 1412 355 1624 510 1818 690 887 185 1016 230 1130 275 1070 245 1220 1383 405 1235 320 1436 430 1610 555 1426 430 1636 5 1815 775 881 230 1012 285 1135 335 1070 295 1220 370 1385 470 1240 385 1437 5 1599 645 1433 510 1618 670 1694 735 876 270 999 325 1135 390 10 3 1216 0 1381 545 1243 5 1430 0 1517 640 1428 5 1512 635 1525 660 18
*DH2D120A9V5V - FURNACE AIRF () AND POWER () VS. WITH FILTER 1ST 2ND AIRF 1st CAPACITY = 2nd CAPACITY = 74,880 115,200 SW 8 SW 7 0.1 0.3 0.5 0.7 0.9 ON ON MEDIUM NOTES: * First letter may be "A" or "T" ** Factory setting OFF ON ** ON OFF OFF OFF ON ON MEDIUM OFF ON ** ON OFF OFF OFF 1025 65 1 230 13 280 15 43 400 15 66 18 660 20 860 2105 1025 65 200 270 13 340 15 43 0 15 66 470 18 7 2000 51 880 20 940 67 240 330 13 0 15 43 0 15 66 540 18 780 18 810 1 54 880 67 290 390 13 470 15 43 620 15 66 610 1 60 720 1 60 7 1775 820 67 340 4 13 530 14 46 14 71*** 690 10 69 640 15 66 670 1625 63 7 *DH2D120A9V5V - FURNACE COOLING AIRF () AND POWER () VS. WITH FILTER OUTDOOR UNIT SIZE (TONS) 3.5 4.0 5 AIRF (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) (3 /TON) (400 /TON) (4 /TON) SW 1 SW 2 SW 3 SW 4 0.1 0.3 0.5 0.7 0.9 OFF ON OFF ON OFF ON OFF OFF OFF ON ON OFF ON OFF OFF ON ON OFF OFF OFF ON OFF ON OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF ON OFF NOTES: * - First letter may be "A" or "T" 1. At continuous fan setting: Heating or Cooling airflows are approximately % of selected cooling value. 2. airflow (3 cfm/ton) is COMFORT & HUMID CLIMATE setting; airflow (400 cfm/ton) is typical setting; airflow (4 cfm/ton) is DRY CLIMATE setting. 1225 240 1 4 300 1 460 1 610 17 0 2000 830 2100 970 1225 280 390 1 520 1 530 1 17 640 2000 860 2000 910 1225 340 470 1 590 4 1 610 1 760 17 720 18 1 8 1225 400 520 1 640 520 1 670 16 690 16 680 1 740 16 780 1225 4 0 14 0 14 10 630 14 610 15 660 1 710 19
Maximum Vent Length Table ALTITUDE VENT LENGTH TABLE MAXIMUM TOTAL EQUIVALENT LENGTH IN FEET FOR VENT AND INLET AIR (SEE NOTES) 0-7,000 Feet 2 INCH PIPE 2.5 INCH PIPE 3 or 4 INCH PIPE *UH/DH2B060A9V3VB 200 200 200 *UH/DH2B080A9V3VB *UH/DH2B080A9V4VB *UH/DH2C100A9V4VB *UH2C100A9V5VB 120 200 Not Allowed 60 200 *UH/DH2D120A9V5VB Not Allowed Not Allowed 200 7,000-9,0 Feet 2 INCH PIPE 2.5 INCH PIPE 3 or 4 INCH PIPE *UH/DH2B060A9V3VB 100 100 100 *UH/DH2B080A9V3VB *UH/DH2B080A9V4VB *UH/DH2C100A9V4VB *UH2C100A9V5VB 25 60 100 Not Allowed 30 100 *UH/DH2D120A9V5VB Not Allowed Not Allowed 100 9,0-12,000 Feet 2 INCH PIPE 2.5 INCH PIPE 3 or 4 INCH PIPE *UH/DH2B060A9V3VB *UH/DH2B080A9V3VB *UH/DH2B080A9V4VB *UH/DH2C100A9V4VB *UH2C100A9V5VB Not Allowed 30 Not Allowed Not Allowed *UH/DH2D120A9V5VB Not Allowed Not Allowed NOTES: * - First letter may be "A" or "T" 1. Minimum vent length for all models: 3' horizontal or 3' vertical. 2. DO NOT MIX PIPE DIAMETERS IN THE SAME LENGTH OF PIPE OUTSIDE THE FURNACE CABINET (Except adapters at the top of the furnace). If different inlet and vent pipe sizes are used, the vent pipe must adhere to the maximum length limit shown in the table above (See note 6 below for exception). The inlet pipe can be of a larger diameter, but never smaller than the vent pipe. 3. MAXIMUM PIPE LENGTHS MUST NOT BE EXCEEDED! THE LENGTH SHOWN IS NOT A COMBINED TOTAL, IT IS THE MAXIMUM LENGTH OF EACH (Vent or Inlet air pipes). 4. One SHORT radius 90 elbow is equivalent to 10' of 3" or 4" pipe and one LONG radius elbow is equivalent to 6' of 3" or 4" pipe. One 90 elbow is equivalent to 7½' of 2½" pipe or 5' of 2" pipe. Two 45 elbows equal one 90 elbow. 5. The termination tee or bend must be included in the total number of elbows. If the BAYAIR30AVENTA termination kit is used, the equivalent length of pipe is 5 feet. BAYVENT200B equivalent length is 0 feet. 6. Pipe adapters are field supplied (except for the *UH/DH2D120 models). 7. For Canadian applications ONLY, IPEX 196 may be used for horizontal and vertical terminations. IPEX 081216, IPEX 081218, and IPEX 081219 may only be used for horizontal vent terminations. Equivalent lengths are IPEX 199 = 5 feet, IPEX 081216 = 11 feet, IPEX 081218 = 16 feet, and IPEX 081219 = 21 feet 20
Electrical Data *UH2 WIRING DIAGRAM 21 From drawing D3303
Electrical Data *UH2 SCHEMATIC DIAGRAM From drawing D3303 22
Electrical Data *DH2 WIRING DIAGRAM 23 From drawing D3304
Electrical Data *DH2 SCHEMATIC DIAGRAM From drawing D3304 24
Field Wiring SEE NOTE 6 FIELD WIRING DIAGRAM FOR VARIABLE SPEED 2 FURNACE 1 USING A 1 THERMOSTAT NO COOLING Y1/Ylo W14 W14 JUMPER SEE NOTE 11 SEE NOTE 9 1. Be sure power agrees with equipment nameplates. 2. Low voltage (24 volt wiring) to be No. 18 A.W.G. min. 3. Grounding of equipment must comply with local codes. 4. Set thermostat heat anticipator per unit wiring diagram. 5. These leads provide 115V. power for connection of electronic air cleaner and humidifier MAX. load 1.0 amps each. 6. When a single stage heating thermostat without fan switch is used, no wiring on "G" terminal is used. 7. W1 and W2 must be jumpered together for proper operation. Second stage heat will begin based on IFC switch setting. 8. Set dip switches with power off per installation instructions to set airflow and indoor fan off delays. 9. Continuous fan airflow can be increased by adding this jumper. 10. This wire is only for thermostats requiring connection to transformer common terminal. 11. Optional humidistat is to be connected between R and BK. Factory installed jumper R to BK on the circuit board must be cut if optional humidistat is used. The jumper must also be cut when applying an airflow command signal to the BK input such as with the variable speed single-zone and multi-zone system controllers. On single speed cooling only/non-heat pump systems, jumper Y to O for proper operation of the delay profiles and the humidistat. For two compressor or two speed systems, jumper YLo to O. FIELD ADDED JUMPER W1 TO W2. SEE FURNACE WIRING DIAGRAM FOR 2ND TIMING. B/C SEE NOTE 10 B/C TO 115 V 1 PH., 60 HZ., POWER SUPPLY PER LOCAL CODES HUM SEE NOTE 5 EAC SEE NOTE 5 Figure 60 From Dwg. B342027 Rev. 1 25
Field Wiring FIELD WIRING DIAGRAM FOR VARIABLE SPEED 2 FURNACE 2 USING A 2 THERMOSTAT NO COOLING Y1/Ylo W14 W14 JUMPER SEE NOTE 9 SEE NOTE 7 1. Be sure power agrees with equipment nameplates. 2. Low voltage (24 volt wiring) to be No. 18 A.W.G. min. 3. Grounding of equipment must comply with local codes. 4. Set thermostat heat anticipator per unit wiring diagram. 5. These leads provide 115V. power for connection of electronic air cleaner and humidifier MAX. load 1.0 amps each. 6. This wire is only for thermostats requiring connection to transformer common terminal. 7. Continuous fan airflow can be increased by adding this jumper. 8. Set dip switches with power off per installation instructions to set airflow and indoor fan off delays. 9. Optional humidistat is to be connected between R and BK. Factory installed jumper R to BK on the circuit board must be cut if optional humidistat is used. The jumper must also be cut when applying an airflow command signal to the BK input such as with the variable speed single-zone and multi-zone system controllers. On single speed cooling only/non-heat pump systems, jumper Y to O for proper operation of the delay profiles and the humidistat. For two compressor or two speed systems, jumper YLo to O. B/C SEE NOTE 6 B/C TO 115 V 1 PH., 60 HZ., POWER SUPPLY PER LOCAL CODES HUM SEE NOTE 5 EAC SEE NOTE 5 From Dwg. B342025 Rev. 0 Figure 61 26
Field Wiring FIELD WIRING DIAGRAM FOR VARIABLE SPEED 2 FURNACE 1, 1 COOLING USING A 1, 1 COOLING THERMOSTAT (OUTDOOR SECTION WITHOUT TRANSFORMER) W14 W14 JUMPER SEE NOTE 9 OUTDOOR UNIT (NO TRANSFORMER) Y1/Ylo SEE NOTE 7 FIELD ADDED JUMPER W1 TO W2. SEE FURNACE WIRING DIAGRAM FOR 2ND TIMING. B/C SEE NOTE 6 B/C TO 115 V 1 PH., 60 HZ., POWER SUPPLY PER LOCAL CODES HUM SEE NOTE 5 EAC SEE NOTE 5 From Dwg. B342022 Rev. 1 Figure 62 27
Field Wiring FIELD WIRING DIAGRAM FOR VARIABLE SPEED 2 FURNACE 2, 1 COOLING USING A 2, 1 COOLING THERMOSTAT (OUTDOOR SECTION WITHOUT TRANSFORMER) W14 SEE NOTE 9 W14 JUMPER SEE NOTE 9 OUTDOOR UNIT (NO TRANSFORMER) Y1/Ylo SEE NOTE 7 B/C SEE NOTE 6 B/C TO 115 V 1 PH., 60 HZ., POWER SUPPLY PER LOCAL CODES HUM SEE NOTE 5 EAC SEE NOTE 5 From Dwg. B342020 Rev. 0 Figure 63 28
Field Wiring FIELD WIRING DIAGRAM FOR VARIABLE SPEED 2 FURNACE 2, 2 STEP D COOLING (OUTDOOR SECTION WITHOUT TRANSFORMER) SEE NOTE 7 W14 R-BK JUMPER SEE NOTE 9 OUTDOOR UNIT (NO TRANSFORMER) B SEE NOTE 6 B/C TO 115 V 1 PH., 60 HZ., POWER SUPPLY PER LOCAL CODES HUM SEE NOTE 5 EAC SEE NOTE 5 Figure 64 HUMIDISTAT HOOKUP If an optional Humidistat is to be connected between R and BK, the factory installed jumper between R and BK on the circuit board must be cut. If an optional Humidistat is used, the jumper must also be cut when applying an airflow command signal to the BK input such as with the variable speed single-zone and multi-zone system controller. On single speed cooling only/ non-heat pump systems, jumper Y to O for proper operation of the delay profiles and the Humidistat. For two compressor or two speed systems, jumper YLO to O. W14 BK JUMPER The factory installed jumper between R and BK on the circuit board must be cut if an optional Humidistat is installed. BLK/TWIN W2 W1 R G B Y YLO O 1 2 ON OFF 1 2 BLK/TWIN W2 W1 R G B Y YLO O Figure 65 29
Dimensions *UH2 UPF / HORIZONTAL OUTLINE DRAWING (ALL DIMENSIONS ARE IN INCHES) 30
Dimensions *DH2 DOWNF / HORIZONTAL OUTLINE DRAWING (ALL DIMENSIONS ARE IN INCHES) 31
Trane 6200 Troup Highway Tyler, TX 707 www.trane.com Trane has a policy of continuous product and product data improvement and reserves the right to change design and specifications without notice.