AIR HANDLERS AIR HANDLERS AIR HANDLERS. RHLA- High Efficiency. featuring R-22 Refrigerant. RHLL- High Efficiency
|
|
|
- Edgar Gordon
- 7 years ago
- Views:
Transcription
1 FORM NO. H11-52 REV. 3 Supersedes Form H11-52 Rev. 2 AIR HANDLERS AIR HANDLERS RHLA- Efficiency featuring R-22 Refrigerant RHLL- Efficiency featuring Earth-Friendly R-10A Refrigerant earth friendly refrigerant AIR HANDLERS RHSA- Standard Efficiency featuring R-22 Refrigerant RHSL- Standard Efficiency featuring Earth-Friendly R-10A Refrigerant Features earth friendly refrigerant RHLA/RHLL feature GE s new X-13 motor which provides enhanced SEER performance with most Rheem outdoor units. 1 1 /2 ton [5.3 kw] through 5 ton [17.6 kw] models are between 2 1 /2 to 55 1 /2 inches [1080 to 110 mm] tall and 22 inches [559 mm] deep. Versatile -way convertible design for upflow, downflow, horizontal left and horizontal right applications. Factory-installed high efficiency indoor coil. All models meet or exceed 330 to 00 CFM [156 to 189 L/s] per ton at.3 inches [.7 kpa] of external static pressure. Enhanced airflow up to.7" external static pressure. Sturdy construction with 1.0 inch [.2 kpa] of reinforced foil faced jacket insulation for excellent thermal and sound insulation. Field-installed auxiliary electric heater kits provide exact heat for indoor comfort. Kits include circuit breakers which meet UL and cul requirements for service disconnect.
2 Engineering Features RHLA/RHLL/RHSA/RHSL- Series The most compact unit design available, all standard heat air handler models only 2 1 /2 to 55 1 /2 inches [1079 to 109 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved copper tubing. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2 inches [51 mm] for 1 1 /2 inch [38 mm] conduit. Front refrigerant and drain connections. GENERAL TERMS OF LIMITED WARRANTY Rheem will furnish a replacement for any part of this product which fails in normal use and service within the applicable periods stated, in accordance with the terms of the limited warranty. Indoor Coil leaks caused by factory defects...five (5) Years Electric Heating Element...Five (5) Years Any Other Part...Five (5) Years For Complete Details of the Limited Warranty, Including Applicable Terms and Conditions, See Your Local Installer or Contact the Manufacturer for a Copy. 2 Rheem Manufacturing Company
3 Identification R H L A HM 2 17 J A Design Variation A = 1st Design R H S A HM J A Voltage A = 115/1/60 J = 208/20/1/60 Cabinet Size 17 = 17.5" [31.8 mm] ( CFM) 21 = 21" [533. mm] ( CFM) 2 = 2.5" [609.6 mm] ( CFM) Capacity 2 = 18,000/2,000 BTU/H [5.27/7.03 kw] 36 = 30,000/36,000 BTU/H [6.79/10.55 kw] 8 = 2,000/8,000 BTU/H [12.31/1.06 kw] 60 = 60,000 BTU/H [17.58 kw] HM = A/C or HP Multi-Position (Vertical Upflow/Horizontal Left is the factory configuration) Refrigerant A = R-22 L = R-10A L = Efficiency (X-13 ) Classification H = Air Handler Rheem Design Variation A = 1st Design Voltage A = 115/1/60 D = 80V-3-60 J = 208/20/1/60 Cabinet Size 17 = 17.5" [31.8 mm] ( CFM) 21 = 21" [533. mm] ( CFM) 2 = 2.5" [609.6 mm] ( CFM) Capacity 18 = 18,000 BTU/H [5.27 kw] 2 = 2,000 BTU/H [7.03 kw] 30 = 30,000 BTU/H [8.79 kw] 36 = 36,000 BTU/H [10.55 kw] 2 = 2,000 BTU/H [12.31 kw] 8 = 8,000 BTU/H [1.06 kw] 60 = 60,000 BTU/H [17.58 kw] Available s at A Voltage RHSA(L)-HM1817AA RHSA(L)-HM217AA RHSA(L)-HM3017AA RHSA(L)-HM3617AA RHSA(L)-HM221AA RHSA(L)-HM821AA RHLA(L)-HM217AA RHLA(L)-HM3617AA RHLA(L)-HM821AA RHLA(L)-HM82AA RHLA(L)-HM602AA Available s at J Voltage RHSA(L)-HM1817JA RHSA(L)-HM217JA RHSA(L)-HM3017JA RHSA(L)-HM3617JA RHSA(L)-HM3621JA RHSA(L)-HM221JA RHSA(L)-HM821JA RHSA(L)-HM82JA RHSA(L)-HM602JA* RHLA(L)-HM217JA RHLA(L)-HM3617JA RHLA(L)-HM821JA RHLA(L)-HM82JA RHLA(L)-HM602JA Available s at D Voltage RHSA(L)-HM3617DA RHSA(L)-HM3621DA RHSA(L)-HM221DA RHSA(L)-HM821DA RHSA(L)-HM82DA RHSA(L)-HM602DA *RHSA(L)-HM602JA is ARI rated for three phase application only. Supply circuit protective devices may be fuses or HACR type circuit breakers. Largest motor load is included in single circuit and multiple circuit. If non-standard fuse size is specified, use the next larger fuse size. J Voltage (230V) single-phase air handler is designed to be used with single or three phase 230 volt power. In the case of connecting 3-phase power to the air handler terminal block, bring only two leads to the terminal block. Cap, insulate and fully secure the third lead. The air handlers are shipped from the factory with the proper indoor coil installed, and cannot be ordered without a coil. The air handlers do not have an internal filter rack. An external filter rack or other means of filtration is required. HM = A/C or HP, Multi-Position (Vertical Upflow/Horizontal Left is the factory configuration) Refrigerant A = R-22 L = R-10A S = Standard (PSC ) Classification H = Air Handler Rheem Rheem Manufacturing Company 3
![06 kw] 60 = 60,000 BTU/H [17.](/docs-images/46/21651802/images/page_3.jpg "58 kw] HM = A/C or HP Multi-Position (Vertical Upflow/Horizontal Left is the factory configuration) Refrigerant A = R-22 L = R-10A L = Efficiency (X-13 ) Classification H = Air Handler Rheem Design")
4 Unit Dimensions ELECTRICAL CONNECTIONS MAY EXIT TOP OR EITHER SIDE HIGH VOLTAGE CONNECTION 7/8 [22.2 mm], 13/32 [27.8 mm], 131/32 [50 mm] DIA. KNOCKOUTS. SUPPLY AIR 10 5 /16 [262 mm] NOTE: 2 CLEARANCE REQUIRED IN FRONT OF UNIT FOR FILTER AND COIL MAINTENANCE. W LOW VOLTAGE CONNECTION 5/8 [15.9 mm] AND 7/8 [22.2 mm] KNOCKOUT A Return Air Opening Dimensions Cabinet Size Return Air Opening Width (Inches) Return Air Opening Depth/Length (Inches) / / / / / / H AUXILIARY DRAIN CONNECTION 3/ [19.1 mm] FEMALE PIPE THREAD (NPT) HORIZONTAL APPLICATION ONLY PRIMARY DRAIN CONNECTION 3/ [19.1 mm] FEMALE PIPE THREAD (NPT) AUXILIARY DRAIN CONNECTION 3/ [19.1 mm] FEMALE PIPE THREAD (NPT) UPFLOW/DOWNFLOW APPLICATION ONLY LIQUID LINE CONNECTION COPPER (SWEAT) 19 1 /2 [95 mm] RETURN AIR OPENING /16 [551 mm] VAPOR LINE CONNECTION COPPER (SWEAT) UPFLOW UNIT SHOWN: UNIT MAY BE INSTALLED UPFLOW, DOWNFLOW, HORIZONTAL RIGHT OR LEFT AIR SUPPLY. HORIZONTAL ADAPTER KIT VAPOR LINE CONNECTION AUXILIARY HORIZONTAL DRAIN CONNECTION 5 15 /16 [151 mm] 1 /8 [105 mm] 3 1 /16 [76 mm] 1 3 /16 [8 mm] 11 /8 [29 mm] 1 1 /16 [27 mm] 1 3 /8 [35 mm] 2 13 /16 [71 mm] 5 1 / [133 mm] 5 3 /8 [136 mm] PRIMARY DRAIN CONNECTION AUXILIARY UPFLOW/DOWNFLOW DRAIN CONNECTION LIQUID LINE CONNECTION VERTICAL DRAIN PAN ( ) Designates Unit with Double Coil Cabinet Unit Dimensions & Weights Unit Unit Supply Air Flow Unit Weight/Shipping Weight (Lbs.) [kg] Width Height Duct CFM (Nom.) [L/s] Size Unit With W In. [mm] H In. [mm] A In. [mm] Lo Hi Coil (Max. KW) 1817/ /2 [5] 2 1 /2 [1080] 16 1 /2 [06] 600 [283] 800 [378] 82/96 [37/] 3017/ /2 [5] 2 1 /2 [1080] 16 1 /2 [06] 1000 [72] 1200 [566] 92/106 [37/8] /2 [533] 2 1 /2 [1080] 19 1 /2 [95] 1200 [566] 97/112 [/51] 221/ /2 [533] 50 1 /2 [1282] 19 1 /2 [95] 100 [661] 1600 [755] 150/166 [68/75] /2 [622] 55 1 /2 [110] 23 1 /2 [58] 1600 [755] 162/180 [73/81] /2 [622] 55 1 /2 [110] 23 1 /2 [58] 1800 [850] 181/198 [82/90] Rheem Manufacturing Company
![2 mm] KNOCKOUT A Return Air Opening Dimensions Cabinet Size Return Air Opening Width (Inches) Return Air Opening Depth/Length (Inches) 17 15 7 /8 19 3 / 21 19 3 /8 19 3 / 2 22 7 /8 19 3 / H AUXILIARY](/docs-images/46/21651802/images/page_4.jpg "DRAIN CONNECTION 3/ [19.1 mm] FEMALE PIPE THREAD (NPT) HORIZONTAL APPLICATION ONLY PRIMARY DRAIN CONNECTION 3/ [19.1 mm] FEMALE PIPE THREAD (NPT) AUXILIARY DRAIN CONNECTION 3/ [19.")
5 Airflow Directions UPFLOW DOWNFLOW HORIZONTAL LEFT HAND AIRFLOW HORIZONTAL RIGHT HAND AIRFLOW Rheem Manufacturing Company 5
6 Airflow Performance Airflow performance data is based on cooling performance with a coil and no filter in place. Select performance table for appropriate unit size, voltage and number of electric heaters to be used. Make sure external static applied to unit allows operation within the minimum and maximum limits shown in table below for both cooling and electric heat operation. For optimum blower performance, operate the unit in the.3 [8 mm] to.7 inches [18 mm] W.C. external static range. Units with coils should be applied with a minimum of.1 inch [3 mm] W.C. external static range. Airflow Operating Limits Cabinet Size Cooling BTUH x 1,000 Cooling Tons Nominal Heat Pump or Air Conditioning Maximum Heat/Cool CFM [L/s] (37.5 CFM [18 L/s]/1,000 BTUH) (50 CFM [212 L/s]/Ton Nominal) Heat Pump or Air Conditioning Nominal Heat/Cool CFM [L/s] (33.3 CFM [16 L/s]/1,000 BTUH) (00 CFM [189 L/s]/Ton Nominal) Heat Pump or Air Conditioning Minimum Heat/Cool CFM [L/s] (30.0 CFM [1 L/s]/1,255 BTUH) (360 CFM [170 L/s]/Ton Nominal) Maximum kw Electric Heating & Minimum Electric Heat CFM [L/s] [319] 600 [283] 50 [255] [236] [25] 800 [378] 720 [30] [307] [531] 1000 [72] 900 [25] [08] [637] 1200 [566] 1080 [510] [00] [73] 100 [661] 1260 [595] [566] [850] 1600 [755] 10 [680] [600] [850] 1600 [755] 10 [680] [600] Maximum Electric Heat Rise F [ C] 85 [29] 85 [29] 85 [29] 85 [29] 85 [29] 85 [29] 85 [29] [911] 1800 [850] 1620 [765] [821] 85 [29] 6 Rheem Manufacturing Company
7 Airflow Performance Data RHSA/RHSL (PSC ) No with 13 kw -217 No -217 with 13 kw No with 18 kw -3617/-3621 No from Factory Manufacturer Recommended Air-Flow Range (Min/Max) CFM 517/711 CFM [2/336 L/s] 67/661 CFM [230/312 L/s] 67/888 CFM [305/19 L/s] 617/638 CFM [291/395 L/s] 86/100 CFM [08/7 L/s] 81/90 CFM [38/27 L/s] 110/128 CFM [521/589 L/s] Blower Size/ HP [W] # of 1/5 HP [19] 1/5 HP [19] 1/5 HP [19] 1/5 HP [19] 1/ HP [186] 1/ HP [186] 11x8 1/3 HP [29] PSC CFM [L/s] Air Delivery/RPM/Watts 20 Volts External Static Pressure Inches W.C. [kpa] 0.1 [.02] 0.2 [.05] 0.3 [.07] 0. [.10] 0.5 [.12] 0.6 [.15] 0.7 [.17] CFM 668 [315] 637 [301] 595 [281] 560 [26] 517 [2] RPM Watts CFM 711 [336] 662 [312] 61 [290] RPM Watts CFM 638 [301] 607 [286] 565 [267] 530 [250] 87 [230] RPM Watts CFM 661 [312] 612 [289] 56 [266] RPM Watts CFM 817 [386] 779 [368] 757 [357] 693 [327] 67 [305] RPM Watts CFM 888 [19] 828 [391] 77 [365] RPM Watts CFM 787 [371] 79 [353] 727 [33] 663 [313] 617 [291] RPM Watts CFM 838 [395] 778 [367] 72 [32] RPM Watts CFM 1022 [82] 987 [66] 90 [] 903 [26] 86 [08] RPM Watts CFM 100 [7] 951 [9] 883 [17] RPM Watts CFM 972 [59] 937 [2] 890 [20] 853 [03] 81 [38] RPM Watts CFM 90 [27] 851 [02] 783 [370] RPM Watts CFM 1229 [580] 1201 [567] 1170 [552] 111 [538] 110 [521] RPM Watts CFM 128 [589] 119 [563] 1133 [535] RPM Watts Notes: The above airflow table lists the airflow information for air handlers without heater and air handler with maximum heater allowed for each model. The following formula can be used to calculation the approximate airflow, if a smaller (N kw) than the maximum heater kit is installed. Approximate Airflow = Airflow without heater (Airflow without heater Airflow with maximum heater) x (N kw/maximum heater kw) Rheem Manufacturing Company 7
![HP [19] 1/5 HP [19] 1/5 HP [19] 1/5 HP [19] 1/ HP [186] 1/ HP [186] 11x8 1/3 HP [29] PSC CFM [L/s] Air Delivery/RPM/Watts 20 Volts External Static Pressure Inches W.C. [kpa] 0.1 [.02] 0.2 [.05] 0.3 [.](/docs-images/46/21651802/images/page_7.jpg "07] 0. [.10] 0.5 [.12] 0.6 [.15] 0.7 [.")
8 Airflow Performance Data RHSA/RHSL (PSC ) (con t.) -3617/3621 with 18 kw -221 No -221 with 20 kw -821/-82 No -821/-82 with 25 kw -602 No -602 with 30 kw from Factory Manufacturer Recommended Air-Flow Range (Min/Max) CFM 105/118 CFM [97/52 L/s] 121/1537 CFM [586/725 L/s] 1225/1500 CFM [553/678 L/s] 1572/182 CFM [72/861 L/s] 1225/1500 CFM [709/81 L/s] 1766/1965 CFM [833/927 L/s] 1225/1500 CFM [709/81 L/s] Blower Size/ HP [W] # of 1/3 HP [29] 1/2 HP [373] 1/2 HP [373] 11x11 11x11 PSC CFM [L/s] Air Delivery/RPM/Watts 20 Volts External Static Pressure Inches W.C. [kpa] 0.1 [.02] 0.2 [.05] 0.3 [.07] 0. [.10] 0.5 [.12] 0.6 [.15] 0.7 [.17] CFM 1179 [556] 1151 [53] 1120 [529] 1091 [515] 105 [97] RPM Watts CFM 118 [52] 109 [516] 1033 [87] RPM Watts CFM 1526 [720] 17 [696] 127 [673] 1307 [617] 121 [586] RPM Watts CFM 1537 [725] 118 [669] 133 [630] RPM Watts CFM 156 [687] 10 [663] 1357 [60] 1237 [58] 1171 [553] RPM Watts CFM 137 [678] 1318 [622] 123 [582] RPM Watts CFM 171 [822] 1719 [811] 1667 [787] 1628 [768] 1572 [72] RPM Watts CFM 182 [861] 1767 [83] 1653 [780] RPM Watts CFM 1671 [789] 169 [778] 1597 [75] 1558 [735] 1502 [709] RPM Watts CFM 172 [81] 1667 [787] 1553 [733] RPM Watts CFM 19 [917] 1912 [902] 1860 [878] 1813 [856] 1766 [833] RPM Watts CFM 1965 [927] 1908 [900] 185 [875] RPM Watts CFM 18 [870] 1812 [855] 1760 [831] 1713 [808] 1666 [786] RPM Watts CFM 1865 [880] 1808 [853] 175 [828] RPM Watts Notes: The above airflow table lists the airflow information for air handlers without heater and air handler with maximum heater allowed for each model. The following formula can be used to calculation the approximate airflow, if a smaller (N kw) than the maximum heater kit is installed. Approximate Airflow = Airflow without heater (Airflow without heater Airflow with maximum heater) x (N kw/maximum heater kw) 8 Rheem Manufacturing Company
![121/1537 CFM [586/725 L/s] 1225/1500 CFM [553/678 L/s] 1572/182 CFM [72/861 L/s] 1225/1500 CFM [709/81 L/s] 1766/1965 CFM [833/927 L/s] 1225/1500 CFM [709/81 L/s] Blower Size/ HP [W] # of 1/3 HP [29]](/docs-images/46/21651802/images/page_8.jpg "1/2 HP [373] 1/2 HP [373] 11x11 11x11 PSC CFM [L/s] Air Delivery/RPM/Watts 20 Volts External Static Pressure Inches W.C. [kpa] 0.1 [.02] 0.2 [.05] 0.3 [.07] 0. [.10] 0.5 [.12] 0.6 [.15] 0.7 [.")
9 115/208/80V Airflow Performance Data RHSA/RHSL (PSC ) No with 13 kw -217 No -217 with 13 kw No with 18 kw -3617/-3621 No from Factory Manufacturer Recommended Air-Flow Range (Min/Max) CFM 523/705 CFM [27/333 L/s] 93/655 CFM [233/309 L/s] 682/897 CFM [322/23 L/s] 652/87CFM [308/00 L/s] 883/1015 CFM [17/79 L/s] 833/915 CFM [393/32 L/s] 1062/119 CFM [501/563 L/s] Blower Size/ HP [W] # of 1/5 HP [19] 1/5 HP [19] 1/5 HP [19] 1/5 HP [19] 1/ HP [186] 1/ HP [186] 1/3 HP [29] PSC CFM [L/s] Air Delivery/RPM/Watts 115/208/80 Volts External Static Pressure Inches W.C. [kpa] 0.1 [.02] 0.2 [.05] 0.3 [.07] 0. [.10] 0.5 [.12] 0.6 [.15] 0.7 [.17] CFM 681 [321] 636 [300] 606 [286] 567 [268] 523 [27] RPM Watts CFM 705 [333] 650 [307] 599 [283] RPM Watts CFM 651 [307] 606 [286] 576 [272] 537 [253] 93 [233] RPM Watts CFM 655 [309] 600 [283] 59 [259] RPM Watts CFM 875 [13] 806 [380] 787 [371] 739 [39] 682 [322] RPM Watts CFM 897 [23] 851 [02] 765 [361] RPM Watts CFM 85 [399] 776 [366] 757 [357] 709 [335] 652 [308] RPM Watts CFM 87 [00] 801 [378] 715 [337] RPM Watts CFM 1038 [90] 1010 [77] 976 [61] 925 [37] 883 [17] RPM Watts CFM 1015 [79] 963 [5] 890 [20] RPM Watts CFM 988 [66] 960 [53] 926 [37] 875 [13] 833 [393] RPM Watts CFM 915 [32] 863 [07] 790 [373] RPM Watts CFM 1201 [567] 1170 [552] 111 [538] 110 [521] 1062 [501] RPM Watts CFM 119 [563] 113 [535] 1078 [509] RPM Watts Notes: The above airflow table lists the airflow information for air handlers without heater and air handler with maximum heater allowed for each model. The following formula can be used to calculation the approximate airflow, if a smaller (N kw) than the maximum heater kit is installed. Approximate Airflow = Airflow without heater (Airflow without heater Airflow with maximum heater) x (N kw/maximum heater kw) Rheem Manufacturing Company 9
![Size/ HP [W] # of 1/5 HP [19] 1/5 HP [19] 1/5 HP [19] 1/5 HP [19] 1/ HP [186] 1/ HP [186] 1/3 HP [29] PSC CFM [L/s] Air Delivery/RPM/Watts 115/208/80 Volts External Static Pressure Inches W.C. [kpa] 0.](/docs-images/46/21651802/images/page_9.jpg "1 [.02] 0.2 [.05] 0.3 [.07] 0. [.10] 0.5 [.12] 0.6 [.15] 0.7 [.")
10 115/208/80V Airflow Performance Data RHSA/RHSL (PSC ) -3617/3621 with 18 kw -221 No -221 with 20 kw -821/-82 No -821/-82 with 25 kw -602 No -602 with 30 kw from Factory Manufacturer Recommended Air-Flow Range (Min/Max) CFM 1012/109 CFM [78/516 L/s] 1211/151 CFM [571/71 L/s] 1225/1500 CFM [538/667 L/s] 152/1787 CFM [728/83 L/s] 1225/1500 CFM [695/796 L/s] 1710/1967 CFM [807/928 L/s] 1225/1500 CFM [695/796 L/s] Blower Size/ HP [W] # of 1/3 HP [29] 1/2 HP [373] 1/2 HP [373] 11x11 11x11 PSC CFM [L/s] Air Delivery/RPM/Watts 115/208/80V Volts External Static Pressure Inches W.C. [kpa] 0.1 [.02] 0.2 [.05] 0.3 [.07] 0. [.10] 0.5 [.12] 0.6 [.15] 0.7 [.17] CFM 1151 [53] 1120 [529] 1091 [515] 105 [97] 1012 [78] - - RPM Watts CFM 109 [516] 103 [88] 978 [62] RPM Watts CFM 193 [705] 19 [68] 1363 [63] 1287 [607] 1211 [571] RPM Watts CFM 151 [71] 111 [666] 1315 [621] RPM Watts CFM 123 [672] 1379 [651] 1293 [610] 1217 [57] 111 [538] RPM Watts CFM 11 [667] 1311 [619] 1215 [573] RPM Watts CFM 1711 [807] 1689 [797] 1637 [773] 1598 [75] 152 [728] RPM Watts CFM 1787 [83] 1679 [792] 1575 [73] RPM Watts CFM 161 [77] 1619 [76] 1567 [739] 1528 [721] 172 [695] RPM Watts CFM 1687 [796] 1579 [75] 175 [696] RPM Watts CFM 1866 [881] 1833 [865] 1806 [852] 1772 [836] 1710 [807] RPM Watts CFM 1967 [928] 1916 [90] 1863 [879] RPM Watts CFM 1796 [88] 1763 [832] 1736 [819] 1702 [803] 160 [77] RPM Watts CFM 1867 [881] 1816 [857] 1763 [832] RPM Watts Notes: The above airflow table lists the airflow information for air handlers without heater and air handler with maximum heater allowed for each model. The following formula can be used to calculation the approximate airflow, if a smaller (N kw) than the maximum heater kit is installed. Approximate Airflow = Airflow without heater (Airflow without heater Airflow with maximum heater) x (N kw/maximum heater kw) 10 Rheem Manufacturing Company
![1225/1500 CFM [695/796 L/s] Blower Size/ HP [W] # of 1/3 HP [29] 1/2 HP [373] 1/2 HP [373] 11x11 11x11 PSC CFM [L/s] Air Delivery/RPM/Watts 115/208/80V Volts External Static Pressure Inches W.C. [kpa] 0.](/docs-images/46/21651802/images/page_10.jpg "1 [.02] 0.2 [.05] 0.3 [.07] 0. [.10] 0.5 [.12] 0.6 [.15] 0.7 [.")
11 115V/208V/ Airflow Performance Data RHLA/RHLL (X-13 ) -217 No -217 with 13 kw -217 No -217 with 13 kw No with 18 kw No with 18 kw Tonnage Application 1.5 Ton 1.5 Ton 2 Ton 2 Ton 2.5 Ton 2.5 Ton 3 Ton 3 Ton From Factory Manufacturer Recommended Air-Flow Range (Min/Max) CFM 509/681 CFM [20/321 L/s] 90/666 CFM [231/31 L/s] 730/651 CFM [35/307 L/s] 711/626CFM [336/295 L/s] 935/108 CFM [1/512 L/s] 910/1059 CFM [29/500 L/s] 1130/1275 CFM [533/602 L/s] 1105/1250 CFM [521/590 L/s] Blower Size/ HP [W] X-13 CFM [L/s] Air Delivery/RPM/Watts 115/208/20 Volts External Static Pressure Inches W.C. [kpa] # of 0.1 [.02] 0.2 [.05] 0.3 [.07] 0. [.10] 0.5 [.12] 0.6 [.15] 0.7 [.17] CFM 689 [325] 6 [30] 602 [28] 563 [266] 509 [20] 2 RPM Watts /3 HP [29] 5 CFM 681 [321] 6 [30] 603 [285] 3 RPM Watts CFM 670 [316] 625 [295] 583 [275] 5 [257] 90 [231] 2 RPM Watts /3 HP [29] 5 CFM 666 [31] 629 [297] 588 [277] 3 RPM Watts CFM 875 [13] 839 [396] 80 [379] 762 [360] 730 [35] RPM Watts /3 HP [29] 5 CFM 651 [307] 61 [290] 573 [270] 5 RPM Watts CFM 856 [0] 820 [387] 785 [370] 73 [351] 711 [336] RPM Watts /3 HP [29] 5 CFM 626 [295] 589 [278] 58 [259] 5 RPM Watts CFM 1093 [516] 1050 [96] 1017 [80] 977 [61] 935 [1] 2 RPM Watts /2 HP [373] 5 CFM 108 [512] 100 [91] 1001 [72] 3 RPM Watts CFM 1068 [50] 1025 [8] 992 [68] 952 [9] 910 [29] 2 RPM Watts /2 HP [373] 5 CFM 1059 [500] 1015 [79] 976 [61] 3 RPM Watts CFM 1270 [599] 1237 [58] 1199 [566] 1165 [550] 1130 [533] RPM Watts /2 HP [373] 5 CFM 1275 [602] 12 [587] 1211 [571] 5 RPM Watts CFM 125 [588] 1212 [572] 117 [55] 110 [538] 1105 [521] RPM Watts /2 HP [373] 5 CFM 1250 [590] 1219 [575] 1186 [560] 5 RPM Watts Notes: The above airflow table lists the airflow information for air handlers without heater and air handler with maximum heater allowed for each model. The following formula can be used to calculation the approximate airflow, if a smaller (N kw) than the maximum heater kit is installed. Approximate Airflow = Airflow without heater (Airflow without heater Airflow with maximum heater) x (N kw/maximum heater kw) Rheem Manufacturing Company 11
12 115/208/ Airflow Performance Data RHLA/RHLL (X-13 ) (con t.) -821 No -821 with 20 kw -821 No -821 with 25 kw -82 No -82 with 25 kw -602 No -602 with 30 kw Tonnage Application 3.5 Ton 3.5 Ton Ton Ton Ton Ton 5 Ton 5 Ton From Factory Manufacturer Recommended Air-Flow Range (Min/Max) CFM 1337/17 CFM [631/683 L/s] 1297/1333 CFM [612/629 L/s] 1535/165 CFM [72/781 L/s] 195/161 CFM [706/762 L/s] 155/1732 CFM [729/817 L/s] 1505/1692 CFM [710/798 L/s] 1739/1905 CFM [821/899 L/s] 1699/1865 CFM [802/880 L/s] Blower Size/ HP [W] # of x x x x PSC CFM [L/s] Air Delivery/RPM/Watts 115/208/20 Volts External Static Pressure Inches W.C. [kpa] 0.1 [.02] 0.2 [.05] 0.3 [.07] 0. [.10] 0.5 [.12] 0.6 [.15] 0.7 [.17] CFM 173 [695] 12 [681] 101 [661] 1373 [68] 1337 [631] RPM Watts CFM 17 [683] 133 [676] 102 [662] RPM Watts CFM 133 [676] 102 [662] 1361 [62] 1333 [629] 1297 [612] RPM Watts CFM 1333 [629] 1300 [613] 1267 [598] RPM Watts CFM 1665 [786] 1631 [770] 1601 [756] 1572 [72] 1535 [72] RPM Watts CFM 165 [781] 162 [766] 1563 [738] RPM Watts CFM 1625 [767] 1591 [751] 1561 [737] 1532 [723] 195 [706] RPM Watts CFM 161 [762] 158 [78] 1523 [719] RPM Watts CFM 178 [825] 1669 [788] 1639 [773] 1599 [755] 155 [729] RPM Watts CFM 1732 [817] 1683 [79] 1630 [769] RPM Watts CFM 1708 [806] 1629 [769] 1599 [755] 1559 [736] 1505 [710] RPM Watts CFM 1692 [798] 163 [775] 1590 [750] RPM Watts CFM 1902 [898] 1862 [879] 1809 [85] 1781 [80] 1739 [821] RPM Watts CFM 1905 [899] 1866 [881] 1832 [865] RPM Watts CFM 1862 [879] 1822 [860] 1769 [835] 171 [822] 1699 [802] RPM Watts CFM 1865 [880] 1826 [862] 1792 [86] RPM Watts Notes: The above airflow table lists the airflow information for air handlers without heater and air handler with maximum heater allowed for each model. The following formula can be used to calculation the approximate airflow, if a smaller (N kw) than the maximum heater kit is installed. Approximate Airflow = Airflow without heater (Airflow without heater Airflow with maximum heater) x (N kw/maximum heater kw) 12 Rheem Manufacturing Company
![[706/762 L/s] 155/1732 CFM [729/817 L/s] 1505/1692 CFM [710/798 L/s] 1739/1905 CFM [821/899 L/s] 1699/1865 CFM [802/880 L/s] Blower Size/ HP [W] # of 5 5 5 11x11 5 11x11 5 11x11 5 11x11 5 5 2 3 PSC](/docs-images/46/21651802/images/page_12.jpg "CFM [L/s] Air Delivery/RPM/Watts 115/208/20 Volts External Static Pressure Inches W.C. [kpa] 0.1 [.02] 0.2 [.05] 0.3 [.07] 0. [.10] 0.5 [.12] 0.6 [.15] 0.7 [.")
13 RHSA/RHSL Electrical Data Blower Only No Electric Heat Cooling Capacity Tons Voltage Application Phase* Hertz HP [W] RPM s Amps. Minimum Ampacity 1 1 /2 1/5 [19] /5 [19] /2 1/ [186] /3 [29] /2 1/2 [373] / [559] /2 1/5 [19] /5 [19] /2 1/ [186] /20 1 & /3 [29] /2 1/2 [373] / [559] / / [559] /3 [29] / /3 [29] / [559] / [559] * Blower motors are all single phase motors. Maximum Protector RHLA/RHLL Electrical Data Blower Only No Electric Heat Cooling Capacity Tons 1 1 /2 & 2 Voltage Application Phase* Hertz HP [W] RPM s Amps. Minimum Ampacity 1/3 [29] /2 & 3 1/2 [373] /20 1 & /2 & 3/ [559] / [559] /2 & 2 1/3 [29] /2 & 3 1/2 [373] /2 & 3/ [559] / [559] * Blower motors are all single phase motors. Maximum Protector Rheem Manufacturing Company 13
![0 15 2 1/5 [19] 1075 2 1.7 3.0 15 2 1 /2 1/ [186] 1075 2 2.5.0 15 208/20 1 & 3 60 3 1/3 [29] 1075 2 2.5.0 15 3 1 /2 1/2 [373] 1075 2 5.2 7.0 15 3/ [559] 1075 2 5.2 7.0 15 5 208/20 3 60 3/ [559] 1075 2 5.](/docs-images/46/21651802/images/page_13.jpg "2 7.0 15 3 1/3 [29] 1075 2 1. 2.0 15 3 1 /2 80 3 60 1/3 [29] 1075 2 2.1 3.0 15 3/ [559] 1075 2 2.2 3.0 15 5 80 3 60 3/ [559] 1075 2 2.2 3.0 15 * Blower motors are all single phase motors.")
14 RHSA/RHSL Electrical Data with Electric Heat Installation of the U.L. Listed original equipment manufacturer provided heater kits listed in the table below is recommended for all auxiliary heating requirements. Nominal Cooling Capacity Tons/ Cabinet Size 1 1/2 & 2/ /2 & 3/ 17 3/ 21 Rheem RXBH-17A03J RXBH-17A05J RXBH-17A07J kw 208/. PH/Hz Elements - kw Per Amps. Ampacity Minimum Ampacity Maximum Protection 2.25/3.0 1/ SINGLE 10.8/ /18 20/20 3.6/.8 1/ SINGLE 17.3/ /28 25/30 5./7.2 1/ SINGLE 26.0/ /0 35/0 RXBH-17A10J 7.2/9.6 1/ SINGLE 3.6/ /53 50/60 RXBH-17A13J 9./12.5 1/ SINGLE 5.1/ /68 60/70 RXBH-17A13J 3.1/.2 1/ MULTIPLE CKT / /2 25/25 6.3/8.3 1/ MULTIPLE CKT / / 0/5 RXBH-17A07C 5./7.2 3/ SINGLE 15.0/ /2 25/25 RXBH-17A10C 7.2/9.6 3/ SINGLE 20.0/ /31 30/35 RXBH-17A13C 9./12.5 3/ SINGLE 26.1/ /0 35/0 RXBH-17A03J 2.25/3.0 1/ SINGLE 10.8/ /19 20/20 RXBH-17A05J 3.6/.8 1/ SINGLE 17.3/ /29 25/30 RXBH-17A07J 5./7.2 1/ SINGLE 26.0/ /1 0/5 RXBH-17A10J 7.2/9.6 1/ SINGLE 3.6/ /5 50/60 RXBH-17A13J 9./12.5 1/ SINGLE 5.1/ /69 60/70 RXBH-17A13J 3.1/.2 1/ MULTIPLE CKT / /25 25/25 6.3/8.3 1/ MULTIPLE CKT / / 0/5 RXBH-17A15J 10.8/1. 1/ SINGLE 51.9/ /79 70/80 RXBH-17A15J 3.6/.8 1/ MULTIPLE CKT / /29 25/30 7.2/9.6 1/ MULTIPLE CKT 2 3.6/0.0 0 /50 5/50 RXBH-17A18J 12.8/17.0 1/ SINGLE 61.6/ /92 90/100 RXBH-17A18J.3/5.7 1/ MULTIPLE CKT / /33 30/35 8.5/11.3 1/ MULTIPLE CKT 2 1.1/ /59 60/60 RXBH-17A07C 5./7.2 3/ SINGLE 15.0/ /25 25/25 RXBH-17A10C 7.2/9.6 3/ SINGLE 20.0/ /32 30/35 RXBH-17A13C 9./12.5 3/ SINGLE 26.1/ /1 0/5 RXBH-17A15C 10.8/1. 3/ SINGLE 30.0/ /7 5/50 RXBH-17A18C 12.8/17.0 3/ SINGLE 35.5/ /55 50/60 RXBH-17A07D 7.2 3/ SINGLE RXBH-17A10D 9.6 3/ SINGLE RXBH-17A15D 1. 3/ SINGLE RXBH-17A18D 17 3/ SINGLE RXBH-2A05J 3.6/.8 1/ SINGLE 17.3/ /29 25/30 RXBH-2A07J 5./7.2 1/ SINGLE 26.0/ /1 0/5 RXBH-2A10J 7.2/9.6 1/ SINGLE 3.6/ /5 50/60 RXBH-2A15J 10.8/1. 1/ SINGLE 51.9/ /79 70/80 RXBH-2A15J 3.6/.8 1/ MULTIPLE CKT / /29 25/30 7.2/9.6 1/ MULTIPLE CKT 2 3.6/0.0 0 /50 5/50 RXBH-2A18J 12.8/17.0 1/ SINGLE 61.6/ /92 90/100 RXBH-2A18J 6./8.5 1/ MULTIPLE CKT / /8 5/50 6./8.5 1/ MULTIPLE CKT / /5 0/5 RXBH-2A07C 5./7.2 3/ SINGLE 15.0/ /25 25/25 RXBH-2A10C 7.2/9.6 3/ SINGLE 20.0/ /32 30/35 RXBH-2A15C 10.8/1. 3/ SINGLE 30.0/ /7 5/50 RXBH-2A18C 12.8/17.0 3/ SINGLE 35.5/ /55 50/60 RXBH-2A07D 7.2 3/ SINGLE RXBH-2A10D 9.6 3/ SINGLE RXBH-2A15D 1. 3/ SINGLE RXBH-2A18D 17 3/ SINGLE Supply circuit protective devices may be fused or HACR type circuit breakers. If non-standard fuse size is specified, use next size larger standard fuse size. If the kit is listed under both single and multiple circuits, the kit is shipped from factory as multiple circuits. For single phase application, Jumper bar kit RXBJ-A21 and RXBJ-A31 can be used to convert multiple circuits to a single supply circuit. Refer to Accessory Section for details. Largest motor load is included in single circuit or circuit 1 of multiple circuit. loads are balanced on 3 PH. models with 3 or 6 heaters only. Electric heater BTUH - (heater watts + motor watts) x 3.1 (see airflow table for motor watts.) No electrical heating elements are permitted to be used with A voltage (115V) air handler. J voltage (230V) single phase air handler is designed to be used with single or three phase 230 volt electric heaters. In the case of connecting 3 phase power to air handler terminal block without the heater, bring only two leads to terminal block. Cap, insulate and fully secure the third lead. Do not use 80 volts electrical heaters on 230 volts air handlers. Do not use 230 volts electrical heaters on 80 volts air handlers. 1 Rheem Manufacturing Company
15 RHSA/RHSL Electrical Data with Electric Heat (con t.) Installation of the U.L. Listed original equipment manufacturer provided heater kits listed in the table below is recommended for all auxiliary heating requirements. Nominal Cooling Capacity Tons/ Cabinet Size 3 1/2 & / 21 and / 2 5/ 2 kw 208/. PH/Hz Elements - kw Per Amps. Ampacity Minimum Ampacity Maximum Protection RXBH-2A05J 3.6/.8 1/ SINGLE 17.3/ /30 30/30 RXBH-2A07J 5./7.2 1/ SINGLE 26.0/ /3 0/5 RXBH-2A10J 7.2/9.6 1/ SINGLE 3.6/ /55 50/60 RXBH-2A15J 10.8/1. 1/ SINGLE 51.9/ /80 70/80 RXBH-2A15J 3.6/.8 1/ MULTIPLE CKT / /30 30/30 7.2/9.6 1/ MULTIPLE CKT 2 3.6/ /50 5/50 RXBH-2A18J 12.8/17 1/ SINGLE 61.6/ /9 90/100 RXBH-2A18J 6./8.5 1/ MULTIPLE CKT /35..0 /50 5/50 6./8.5 1/ MULTIPLE CKT / /5 0/5 RXBH-2A20J 1./19.2 1/ SINGLE 69.2/ / /110 RXBH-2A20J 7.2/9.6 1/ MULTIPLE CKT 1 3.6/ /55 50/60 7.2/9.6 1/ MULTIPLE CKT 2 3.6/ /50 5/50 RXBH-2A25J 18.0/2.0 1/ SINGLE 86./ / /150 RXBH-2A25J (-ton only) 6.0/8.0 1/ MULTIPLE CKT / /7 5/50 6.0/8.0 1/ MULTIPLE CKT / /2 0/5 6.0/8.0 1/ MULTIPLE CKT / /2 0/5 RXBH-2A07C 5./7.2 3/ SINGLE 15.0/ /27 25/30 RXBH-2A10C 7.2/9.6 3/ SINGLE 20.0/ /3 30/35 RXBH-2A15C 10.8/1. 3/ SINGLE 30.0/ /9 5/50 RXBH-2A18C 12.8/17.0 3/ SINGLE 35.6/ /57 50/60 RXBH-2A20C 1./19.2 3/ SINGLE 0.0/ /63 60/70 RXBH-2A20C 7.2/9.6 3/ MULTIPLE CKT / /3 30/35 7.2/9.6 3/ MULTIPLE CKT / /29 25/30 RXBH-2A25C 18.0/2.0 3/ SINGLE 50.0/ /78 70/80 RXBH-2A25C (-ton only) 9.0/12.0 3/ MULTIPLE CKT / /2 0/5 9.0/12.0 3/ MULTIPLE CKT / /37 35/0 RXBH-2A07D 7.2 3/ SINGLE RXBH-2A10D 9.6 3/ SINGLE RXBH-2A15D 1. 3/ SINGLE RXBH-2A18D 17 3/ SINGLE RXBH-2A20D / SINGLE RXBH-2A25D (-ton only) 2.0 3/ SINGLE RXBH-2A07C 5./7.2 3/ SINGLE 15.0/ /28 25/30 RXBH-2A10C 7.2/9.6 3/ SINGLE 20.0/ /35 35/35 RXBH-2A15C 10.8/1. 3/ SINGLE 30.0/3.6. 3/9 5/50 RXBH-2A18C 12.8/17.0 3/ SINGLE 35.6/ /57 50/60 RXBH-2A20C 1./19.2 3/ SINGLE 0.0/ /6 60/70 RXBH-2A20C 7.2/9.6 3/ MULTIPLE CKT / /35 35/35 7.2/9.6 3/ MULTIPLE CKT / /29 25/30 RXBH-2A25C 18.0/2.0 3/ SINGLE 50.0/ /78 70/80 RXBH-2A25C 9.0/12.0 3/ MULTIPLE CKT / /2 0/5 9.0/12.0 3/ MULTIPLE CKT / /37 35/0 RXBH-2A30C 21.6/28.8 3/ SINGLE 60.0/ /93 90/100 RXBH-2A30C 10.8/1. 3/ MULTIPLE CKT /3.7. 3/9 5/ /1. 3/ MULTIPLE CKT / / 0/5 RXBH-2A07D 7.2 3/ SINGLE RXBH-2A10D 9.6 3/ SINGLE RXBH-2A15D 1. 3/ SINGLE RXBH-2A18D 17 3/ SINGLE RXBH-2A20D / SINGLE RXBH-2A25D 2.0 3/ SINGLE RXBH-2A30D / SINGLE Supply circuit protective devices may be fused or HACR type circuit breakers. If non-standard fuse size is specified, use next size larger standard fuse size. If the kit is listed under both single and multiple circuits, the kit is shipped from factory as multiple circuits. For single phase application, Jumper bar kit RXBJ-A21 and RXBJ-A31 can be used to convert multiple circuits to a single supply circuit. Refer to Accessory Section for details. Largest motor load is included in single circuit or circuit 1 of multiple circuit. loads are balanced on 3 PH. models with 3 or 6 heaters only. Electric heater BTUH - (heater watts + motor watts) x 3.1 (see airflow table for motor watts.) No electrical heating elements are permitted to be used with A voltage (115V) air handler. J voltage (230V) single phase air handler is designed to be used with single or three phase 230 volt electric heaters. In the case of connecting 3 phase power to air handler terminal block without the heater, bring only two leads to terminal block. Cap, insulate and fully secure the third lead. Do not use 80 volts electrical heaters on 230 volts air handlers. Do not use 230 volts electrical heaters on 80 volts air handlers. Rheem Manufacturing Company 15
16 RHLA/RHLL Electrical Data with Electric Heat Installation of the U.L. Listed original equipment manufacturer provided heater kits listed in the table below is recommended for all auxiliary heating requirements. Nominal Cooling Capacity Tons/ Cabinet Size 1 1 /2 & 2/ /2 & 3/ /2 & / 21 Rheem KW 208/ PH/HZ Elements - KW Per Type Supply Single Multiple Amps. Ampacity Minimum Ampacity Maximum Protection RXBH-17A03J 2.25/3.0 1/ SINGLE 10.8/ /18 20/20 RXBH-17A05J 3.6/.8 1/ SINGLE 17.3/ /27 25/30 RXBH-17A07J 5./7.2 1/ SINGLE 26.0/ /0 35/0 RXBH-17A10J 7.2/9.6 1/ SINGLE 3.6/ /52 50/60 RXBH-17A13J 9./12.5 1/ SINGLE 5.1/ /68 60/70 RXBH-17A13J 3.1/.2 1/ MULTIPLE CKT / /2 25/25 6.3/8.3 1/ MULTIPLE CKT / / 0/5 RXBH-17A07C 5./7.2 3/ SINGLE 15.0/ /2 25/25 RXBH-17A10C 7.2/9.6 3/ SINGLE 20.0/ /31 30/35 RXBH-17A13C 9./12.5 3/ SINGLE 26.1/ /0 35/0 RXBH-17A03J 2.25/3.0 1/ SINGLE 10.8/ /19 20/20 RXBH-17A05J 3.6/.8 1/ SINGLE 17.3/ /29 25/30 RXBH-17A07J 5./7.2 1/ SINGLE 26.0/ /1 0/5 RXBH-17A10J 7.2/9.6 1/ SINGLE 3.6/ /5 50/60 RXBH-17A13J 9./12.5 1/ SINGLE 5.1/ /69 60/70 RXBH-17A13J 3.1/.2 1/ MULTIPLE CKT / /26 25/30 6.3/8.3 1/ MULTIPLE CKT / / 0/5 RXBH-17A15J 10.8/1. 1/ SINGLE 51.9/ /79 70/80 RXBH-17A15J 3.6/.8 1/ MULTIPLE CKT / /29 25/30 7.2/9.6 1/ MULTIPLE CKT 2 3.6/0.0 0 /50 5/50 RXBH-17A18J 12.8/17.0 1/ SINGLE 61.6/ /92 90/100 RXBH-17A18J.3/5.7 1/ MULTIPLE CKT / /33 30/35 8.5/11.3 1/ MULTIPLE CKT 2 1.1/ /59 60/60 RXBH-17A07C 5./7.2 3/ SINGLE 15.0/ /25 25/25 RXBH-17A10C 7.2/9.6 3/ SINGLE 20.0/ /33 30/35 RXBH-17A13C 9./12.5 3/ SINGLE 26.1/ /1 0/5 RXBH-17A15C 10.8/1. 3/ SINGLE 30.0/ /7 5/50 RXBH-17A18C 12.8/17.0 3/ SINGLE 35.5/ /55 50/60 RXBH-2A05J 3.6/.8 1/ SINGLE 17.3/ /30 30/30 RXBH-2A07J 5./7.2 1/ SINGLE 26.0/ /3 0/5 RXBH-2A10J 7.2/9.6 1/ SINGLE 3.6/ /55 50/60 RXBH-2A15J 10.8/1. 1/ SINGLE 51.9/ /80 70/80 RXBH-2A15J 3.6/.8 1/ MULTIPLE CKT / /30 30/30 7.2/9.6 1/ MULTIPLE CKT 2 3.6/ /50 5/50 RXBH-2A18J 12.8/17 1/ SINGLE 61.6/ /9 90/100 RXBH-2A18J 6./8.5 1/ MULTIPLE CKT / /9 5/50 6./8.5 1/ MULTIPLE CKT / /5 0/5 RXBH-2A20J 1./19.2 1/ SINGLE 69.2/ / /110 RXBH-2A20J 7.2/9.6 1/ MULTIPLE CKT 1 3.6/ /55 50/60 7.2/9.6 1/ MULTIPLE CKT 2 3.6/ /50 5/50 RXBH-2A25J 18.0/2.0 1/ SINGLE 86./ / / /8.0 1/ MULTIPLE CKT / /7 5/50 RXBH-2A25J 6.0/8.0 1/ MULTIPLE CKT / /2 0/5 (-ton only) 6.0/8.0 1/ MULTIPLE CKT / /2 0/5 RXBH-2A07C 5./7.2 3/ SINGLE 15.0/ /27 25/30 RXBH-2A10C 7.2/9.6 3/ SINGLE 20.0/ /3 30/35 RXBH-2A15C 10.8/1. 3/ SINGLE 30.0/ /8 5/50 RXBH-2A18C 12.8/17.0 3/ SINGLE 35.6/ /56 50/60 RXBH-2A20C 1./19.2 3/ SINGLE 0.0/ /63 60/70 RXBH-2A20C 7.2/9.6 3/ MULTIPLE CKT / /3 30/35 7.2/9.6 3/ MULTIPLE CKT / /29 25/30 RXBH-2A25C 18.0/2.0 3/ SINGLE 50.0/ /77 70/80 RXBH-2A25C (-ton only) Supply circuit protective devices may be fused or HACR type circuit breakers. If non-standard fuse size is specified, use next size larger standard fuse size. If the kit is listed under both single and multiple circuits, the kit is shipped from factory as multiple circuits. For single phase application, Jumper bar kit RXBJ-A21 and RXBJ-A31 can be used to convert multiple circuits to a single supply circuit. Refer to Accessory Section for details. Largest motor load is included in single circuit or circuit 1 of multiple circuit. loads are balanced on 3 PH. models with 3 or 6 heaters only. Electric heater BTUH - (heater watts + motor watts) x 3.1 (see airflow table for motor watts.) 9.0/12.0 3/ MULTIPLE CKT / /1 0/5 9.0/12.0 3/ MULTIPLE CKT / /37 35/0 No electrical heating elements are permitted to be used with A voltage (115V) air handler. J voltage (230V) single phase air handler is designed to be used with single or three phase 230 volt electric heaters. In the case of connecting 3 phase power to air handler terminal block without the heater, bring only two leads to terminal block. Cap, insulate and fully secure the third lead. Do not use 80 volts electrical heaters on 230 volts air handlers. Do not use 230 volts electrical heaters on 80 volts air handlers. 16 Rheem Manufacturing Company
17 RHLA/RHLL Electrical Data with Electric Heat (con t.) Installation of the U.L. Listed original equipment manufacturer provided heater kits listed in the table below is recommended for all auxiliary heating requirements. Nominal Cooling Capacity Tons/ Cabinet Size & 5/ 2 Rheem KW 208/ PH/HZ Elements - KW Per Type Supply Single Multiple Amps. Ampacity Minimum Ampacity Maximum Protection RXBH-2A07J 5./7.2 1/ SINGLE 26.0/ / 0/5 RXBH-2A10J 7.2/9.6 1/ SINGLE 3.6/ /56 50/60 RXBH-2A15J 10.8/1. 1/ SINGLE 51.9/ /81 80/90 RXBH-2A15J 3.6/.8 1/ MULTIPLE CKT / /31 30/35 7.2/9.6 1/ MULTIPLE CKT 2 3.6/0.0 0 /50 5/50 RXBH-2A18J 12.8/17 1/ SINGLE 61.6/ /95 90/100 RXBH-2A18J 6./8.5 1/ MULTIPLE CKT / /50 5/50 6./8.5 1/ MULTIPLE CKT / /5 0/5 RXBH-2A20J 1./19.2 1/ SINGLE 69.2/ / /110 RXBH-2A20J 7.2/9.6 1/ MULTIPLE CKT 1 3.6/ /56 50/60 7.2/9.6 1/ MULTIPLE CKT 2 3.6/0.0 0 /50 5/50 RXBH-2A25J 18.0/2.0 1/ SINGLE 86./ / / /8.0 1/ MULTIPLE CKT / /8 5/50 RXBH-2A25J 6.0/8.0 1/ MULTIPLE CKT / /2 0/5 6.0/8.0 1/ MULTIPLE CKT / /2 0/5 RXBH-2A30J 21.6/28.8 1/ SINGLE 103.8/ / / /9.6 1/ MULTIPLE CKT 1 3.6/ /56 50/60 RXBH-2A30J 7.2/9.6 1/ MULTIPLE CKT 2 3.6/0.0 0 /50 5/50 (5-ton only) 7.2/9.6 1/ MULTIPLE CKT 3 3.6/0.0 0 /50 5/50 RXBH-2A07C 5./7.2 3/ SINGLE 15.0/ /28 25/30 RXBH-2A10C 7.2/9.6 3/ SINGLE 20.0/ /35 35/35 RXBH-2A15C 10.8/1. 3/ SINGLE 30.0/3.6.6 /9 5/50 RXBH-2A18C 12.8/17.0 3/ SINGLE 35.6/ /57 60/60 RXBH-2A20C 1./19.2 3/ SINGLE 0.0/ /6 60/70 RXBH-2A20C 7.2/9.6 3/ MULTIPLE CKT / /35 35/35 7.2/9.6 3/ MULTIPLE CKT / /29 25/30 RXBH-2A25C 18.0/2.0 3/ SINGLE 50.0/ /78 70/80 RXBH-2A25C 9.0/12.0 3/ MULTIPLE CKT / /2 0/5 9.0/12.0 3/ MULTIPLE CKT / /37 35/0 RXBH-2A30C 21.6/28.8 3/ SINGLE 60.0/ /93 90/100 RXBH-2A30C (5-ton only) 10.8/1. 3/ MULTIPLE CKT /3.7.6 /50 5/ /1. 3/ MULTIPLE CKT / / 0/5 Supply circuit protective devices may be fused or HACR type circuit breakers. If non-standard fuse size is specified, use next size larger standard fuse size. If the kit is listed under both single and multiple circuits, the kit is shipped from factory as multiple circuits. For single phase application, Jumper bar kit RXBJ-A21 and RXBJ-A31 can be used to convert multiple circuits to a single supply circuit. Refer to Accessory Section for details. Largest motor load is included in single circuit or circuit 1 of multiple circuit. loads are balanced on 3 PH. models with 3 or 6 heaters only. Electric heater BTUH - (heater watts + motor watts) x 3.1 (see airflow table for motor watts.) No electrical heating elements are permitted to be used with A voltage (115V) air handler. J voltage (230V) single phase air handler is designed to be used with single or three phase 230 volt electric heaters. In the case of connecting 3 phase power to air handler terminal block without the heater, bring only two leads to terminal block. Cap, insulate and fully secure the third lead. Do not use 80 volts electrical heaters on 230 volts air handlers. Do not use 230 volts electrical heaters on 80 volts air handlers. Rheem Manufacturing Company 17
18 Electrical Wiring: Power Wiring Field wiring must comply with the National Electrical Code (C.E.C. in Canada) and any applicable local ordinance. Supply wiring must be 75 C minimum copper conductors only. See electrical data for product Ampacity rating and Protector requirement. Grounding This product must be sufficiently grounded in accordance with National Electrical Code (C.E.C. in Canada) and any applicable local ordinance. A grounding lug is provided. Accessories-Kits Parts Combustible Floor Base RXHB- Cabinet Size Jumper Bar Kit 3 Ckt. to 1 Ckt. RXBJ-A31 is used to convert single phase multiple three circuit units to a single supply circuit. Kit includes cover and screw for line side terminals. Jumper Bar Kit 2 Ckt. to 1 Ckt. RXBJ-A21 is used to convert single phase multiple two circuit units to a single supply circuit. Kit includes cover and screw for line side terminals. Note: No jumper bar kit is available to convert three phase multiple two circuit units to a single supply circuit. Auxiliary Horizontal Overflow Pan Accessory RXBM- Nominal Cooling Capacity-Tons External Filter Rack RXHF-B17, B21, B2 Cabinet Size *Accommodates 1" filter Filter Size In. [mm] x 20 [06 x 508] x 20 [508 x 508] 2 25 x 20 [635 x 508] Combustible Floor Base Number RXHB-17 RXHB-21 RXHB-2 Auxiliary Horizontal Overflow Pan Accessory Number 1 1 /2-3 RXBM-AC8 3 1 /2-5 RXBM-AC61 Part Number* RXHF-B17 RXHF-B21 RXHF-B2 A B Auxiliary Electric Kits RXBH- Kits include circuit breakers which meet UL and cul requirements for service disconnect. See the Electric Heat Electrical Data in this specification sheet for specific Kit numbers. Horizontal Adapter Kit RXHH- This horizontal adapter kit is used to convert Upflow/Downflow only models to horizontal flow. See the following table to order proper horizontal adapter kit. Coil Horizontal Adapter Kit Number (Single Qty.) 21 RXHH-A RXHH-A /3621 RXHH-A03 External Filter Base RXHF- Cabinet Size *Accommodates 1" or 2" filter Filter Size In. [mm] x 20 [06 x 508] x 20 [508 x 508] Horizontal Adapter Kit Number (10-Pack Qty.) RXHH-A01 x 10 RXHH-A02 x 10 RXHH-A03 x /82 RXHH-A0 RXHH-A0 x RXHH-A05 RXHH-A05 x 10 Part Number* RXHF-17 RXHF x 20 [635 x 508] RXHF A B RXHF-B RXHF- 1 1 /2 [38 mm] B A 18 Rheem Manufacturing Company
19 NOTES Rheem Manufacturing Company 19
20 Before proceeding with installation, refer to installation instructions packaged with each model, as well as complying with all Federal, State, Provincial, and Local codes, regulations, and practices. RHEEM AIR CONDITIONING DIVISION 5600 Old Greenwood Road, Fort Smith, Arkansas In keeping with its policy of continuous progress and product improvement, Rheem reserves the right to make changes without notice. PRINTED IN U.S.A DC FORM NO. H11-52 REV. 3 Supersedes Form H11-52 Rev. 2
INDOOR COILS. RCFM- featuring Earth-Friendly R-410A Refrigerant CASED/UNCASED COILS FOR GAS AND OIL FURNACES
FORM NO. C11-212 REV. 1 Supersedes Form No. C11-212 INDOOR COILS RCFM- featuring Earth-Friendly R-410A Refrigerant earth friendly refrigerant CASED/UNCASED COILS FOR GAS AND OIL FURNACES AIRFLOW CAPACITIES
INDOOR COILS. RCFA- featuring R-22 Refrigerant RCFL- featuring Earth-Friendly R-410A Refrigerant CASED/UNCASED COILS FOR GAS AND OIL FURNACES
FORM NO. C11-211 REV. 3 Supersedes Form No. C11-211 Rev. 2 INDOOR COILS RCFA- featuring R-22 Refrigerant RCFL- featuring Earth-Friendly R-410A Refrigerant earth friendly refrigerant CASED/UNCASED COILS
INDOOR COILS. RCFL- featuring Industry Standard R-410A Refrigerant CASED/UNCASED COILS FOR GAS AND OIL FURNACES
FORM NO. C11-211 REV. 7 Supersedes Form No. C11-211 Rev. 6 INDOOR COILS RCFL- featuring Industry Standard R-410A Refrigerant CASED/UNCASED COILS FOR GAS AND OIL FURNACES AIRFLOW CAPACITIES 600-1,900 CFM
INDOOR COILS. RCFN- featuring Industry Standard R-410A Refrigerant CASED/UNCASED COILS FOR GAS AND OIL FURNACES
FORM NO. C11-213 REV. 4 Supersedes Form No. C11-213 Rev. 3 INDOOR COILS RCFN- featuring Industry Standard R-410A Refrigerant CASED/UNCASED COILS FOR GAS AND OIL FURNACES AIRFLOW CAPACITIES 600-1,900 CFM
Cased/Uncased Coils For Gas And Oil Furnaces
Indoor Coils Cased/Uncased Coils For Gas And Oil Furnaces RCFL- Series featuring Industry Standard R-410A Refrigerant Airflow Capacity 600-1,900 CFM [283-897 L/s] Rheem Indoor Coils are designed for use
Cooling/Heat Pump Convertible Air Handlers
Cooling/Heat Pump Convertible Air Handlers 2/4TEC3F18-60A1000A 1½ 5 Ton PUB. NO. 22-1774-01-0905 (EN) Features and Benefits 13.0 SEER Ships horizontal converts to vertical by standing unit on end. Six-way
ARMSTRONG AIR HEAT PUMPS www.armstrongair.com
INDEX ELECTRIC FURNACE MODULAR AIR SYSTEM EFC/EFV... 5-10 electric Heat Kits... 5-11 evaporator coils EC1P / EM1P UPFLOW / COUNTERFLOW APPLICATIONS and upflow / horizontal applications (CASED)... 5-6 5-7
Cooling Capacity CFM range @.5 in. w.c. (125 Pa)
N8MXL Product Specifications 80% ECM Single Stage Heating Furnace EASIER TO SELL 80% AFUE Flame roll out sensors standard Category I venting Blocked vent switch 24 VAC humidifier terminal Electronic air
Split System Cooling Product Data
Split System Cooling Product XL16i 1½ 5 Tons PUB. NO. 22-1890-01 Features and Benefits Climatuff compressor Efficiency up to 16.0 SEER and 9.0 HSPF All aluminum Spine Fin coil WeatherGuard fasteners Quick-Sess
Split System Heat Pump Product Data
Split System Heat Pump Product Silver 14 4A6H4 1 1 /2-5 Tons PUB. NO. 12-1175-07 Contents Features and Benefits 2 Model Nomenclature 3 General 4 Product Specifications 4 A-weighted Sound Power Level [db(a)]
F9MXE. Product Specifications
96% AFUE, Single Stage, ECM Gas Furnace EASIER TO SELL 96% AFUE, all models all positions Select models earn the ENERGY STAR (See below, indicated with check mark.) Xtra SEER ECM blower motor Supports
OIL FURNACES CLASSIC PREMIUM CLASS UPFLOW OIL FURNACES. ROBD- SERIES Heating Capacities 56,000 to 151,200 BTU/HR [16.41 to 44.
FORM NO. O11-608 REV. 2 Supersedes Form No. O11-608 Rev. 1 OIL FURNACES CLASSIC PREMIUM CLASS UPF OIL FURNACES ROBD- SERIES Heating Capacities 56,000 to 151,200 BTU/HR [16.41 to 44.30 kw] The Rheem Classic
CB29M Bulletin #490071 February 1996
ENGINEERING DT MTCHED REMOTE SYSTEMS 50hz S LOWER UNITS 50hz ELITE 10 MULTI POSITION LOWER UNITS 20 100 to 49 00 tuh (5.9 to 14.4 kw) Cooling Capacity 19 700 to 49 100 tuh (5.8 to 14.4 kw) Heat Pump Heating
Cooling Capacity CFM range @.5 in. w.c. (125 Pa)
96% AFUE, Single Stage, ECM Gas Furnace EASIER TO SELL 96% AFUE, all models all positions Xtra SEER ECM blower motor Supports two stage cooling units Dehumidification feature in cooling California NOx
Commercial Gas Furnace Upflow
Commercial Gas Furnace Upflow Model G24-200 80% A.F.U.E. 200,000 Btuh Input Heating Cap. 7.5 or 10 Tons Nominal Add-On Cooling GUK FEATURES Certified by A.G.A./C.G.A. Laboratories. Heavy gauge painted
Aluminum Cased Cooling Coils 2-5 Ton 4CXC PUB. NO. 22-1839-03
Aluminum Cased Cooling Coils 2-5 Ton 4CXC PUB. NO. 22-1839-03 Aluminum Cooling Coil Nomenclature 4 C X C B 0 3 6 C C 3 C U A A Refrigerant Type 4 - R410A Product Family T-Premium (Heat Pump or Convertible
G9MXE. Product Specifications
Up to 96% AFUE, Single Stage, ECM Gas Furnace EASIER TO SELL Up to 96% AFUE, all models all positions California NOx approved Select models earn the ENERGY STAR (See below, indicated with check mark.)
Greensource iseries HY Model Unitary Air Handler/Fan Coil
Engineering Submittal Sheet Overview Model Nomenclature HY 035 00-1 HY - HYDRONIC AIR HANDLER NOMINAL CAPACITY IN THOUSANDS OF BTUH VOLTAGE DESIGNATION 1 = 208-230/1/60 ELECTRIC HEAT KW 00 - NO ELECTRIC
Split System Cooling Product Data
Split System Cooling Product Data XR17 4TTR7 2, 3, 4 & 5 Tons PUB. NO. 22-1884-01 Features and Benefits CLIMATUFF 2-stage scroll compressor Efficiency up to 18.0 SEER All Aluminum SPINE FIN coil DURATUFF
Cooling Capacity CFM range @.5 in. w.c. (125 Pa)
96% AFUE, Two Stage ECM Gas Furnace EASIER TO SELL 96% AFUE, all models, all positions Two stage heating operation Xtra SEER ECM blower motor Supports two stage cooling units Dehumidification feature in
DESCRIPTION FEATURES HORIZONTAL DUCT HD. ISO 9001 Certified Quality Management System
TECHNICAL GUIDE ADD - ON COILS FOR USE WITH SPLIT-SYSTEM COOLING & HEAT PUMPS MODELS: MC, PC, FC, HD, UC 600-2000 CFM 1.5-5 TON COILS UPFLOW/DOWNFLOW FULL CASED FC UPFLOW PARTIAL CASED PC UPFLOW UNCASED
Split System Heat Pump Product Data
Split System Heat Pump Product Data XL20i 4TWZ0024, 036, 048 & 060 with ComfortLink II and Charge Assist 2, 3, 4 & 5 Tons PUB. NO. 22-1826-01 Features and Benefits Two Climatuff compressors Efficiency
GCS16 GCS20 WARNING CAUTION
Service Literature Corp. 0110 L6 Revised 12 2004 GCS16/GCS20 SERIES UNITS GCS16 GCS20 2 to 5 Ton GCS16/20 series units in the 2 to 5 ton (7.0 to 17.0 kw) cooling size are packaged combination gas heat
SPLIT-SYSTEM CONDENSING UNITS. 10.00 SEER HRA018 thru 060 (1.5 thru 5 Nominal Tons) DESCRIPTION FEATURES
550.46 -TG1Y (196) SPLIT-SYSTEM CONDENSING S 0 SEER HRA018 thru 060 (1.5 thru 5 Nominal Tons) DESCRIPTION The HRA Series condensing unit is the outdoor part of a versatile system of air conditioning. It
Product Data. FV4C Performancet Series Fan Coil Sizes 002 Thru 006 PREMIUM ENVIRONMENTALLY SOUND FAN COIL
Performancet Series Fan Coil Sizes 002 Thru 006 Product Data PREMIUM ENVIRONMENTALLY SOUND FAN COIL The is the premium air handler combining the proven technology of Carrier fan coils with environmentally
RHEEM RESIDENTIAL AIR CONDITIONING www.rheem.com
INDEX ACCESSORIES... 3-6 barb nylon fittings... 3-6 condensor pads... 3-6 condensor wall bracket... 3-7 electrical... 3-7 PIPE INSULATION... 3-7 REFRIGERATION SERVICE TUBING COPPER... 3-7 COILS INDOOR
TECHNICAL GUIDE 95.5% SINGLE STAGE GAS-FIRED RESIDENTIAL MULTI-POSITION GAS FURNACES MODELS: TG9S DESCRIPTION FEATURES
TECHNICAL GUIDE 95.5% SINGLE STAGE GAS-FIRED RESIDENTIAL MULTI-POSITION GAS FURNACES MODELS: TG9S NATURAL GAS 40-130 MBH INPUT Due to continuous product improvement, specifications are subject to change
M SERIES REFRIGERANT COIL MODULE REFRIGERANT COILS for R-22, R-407C, R-410A
Bulletin 20-20.2 / July 2012 M SERIES REFRIGERANT COIL MODULE REFRIGERANT COILS for R-22, R-407C, R-410A ➀ ➁ ➂ Model Number Key M 2430 C L 1 - A - ➀ Unit Type M=Modular Nominal Capacity 2430=24000 to 30000
E2 Series Electric Furnaces
E2 Series Electric Furnaces Service Manual Table of Contents Electrical Requirements... 10 Codes, Specifications Requirements... 10 Connection Supply Service Wires... 10 Furnace Sequence of Operation...
Split System Cooling Product Data
Split System Cooling Product Data 4TTB3018-060 1½ 5 Tons PUB. NO. 22-1843-14 Features and Benefits Efficiency up to 13.25 SEER All aluminum Spine Fin coil WeatherGuard fasteners Quick-Sess cabinet, easy
Product Data. FV4B Performancet Series Fan Coil Sizes 002 Thru 006 PREMIUM ENVIRONMENTALLY SOUND FAN COIL
Performancet Series Fan Coil Sizes 002 Thru 006 Product Data PREMIUM ENVIRONMENTALLY SOUND FAN COIL The is the premium air handler combining the proven technology of Carrier fan coils with environmentally
WON0502-B INSTALLATION INSTRUCTIONS FOR ELECTRIC FURNACES. Bulletin 30-34 / March 2013
Bulletin 30-34 / March 2013 INSTALLATION INSTRUCTIONS FOR ELECTRIC FURNACES General The information on the following pages is to provide the installer the necessary information to properly install the
Local Dealer: www.cebrands.com
Local Dealer: C.E. LLC - Miami, FL USA www.cebrands.com Res2012-Rev2 QUALITY YOU CAN FEEL Residential Product Line >TCA7,9 Tempstar SmartComfort TXT + Air Conditioner Featuring The Observer Communication
M7RL Series TECHNICAL SPECIFICATIONS. FEATURES and BENEFITS. High Efficiency / Direct Vent Condensing Downflow Gas Furnace
TECHNICAL SPECIFICATIONS M7RL Series High Efficiency / Direct Vent Condensing Downflow Gas Furnace Induced Draft - 9%+ AFUE Input 4,000 thru 7,000 Btuh The high efficiency downflow gas furnace is especially
Split System Heat Pump Product Data
Split System Heat Pump Product Data XR 13 4TWR3018-060 1½ 5 Tons PUB. NO. 22-1795-12 Features and Benefits Climatuff compressor All aluminum Spine Fin coil Quick-Sess cabinet, service access and refrigerant
Split System Cooling Product & Performance Data
Split System Cooling Product & Performance Data XR 13 4TTR3018-060 1½ 5 Tons PUB. NO. 22-1790-02-2607 (EN) Features and Benefits Climatuff compressor Efficiency up to 14.00 SEER All aluminum Spine Fin
G26 Corp. 9721-L11 Revised 07-2001 LENNOXOEMPARTS.COM. Service Literature G26 SERIES UNITS
Service Literature G26 SERIES UNITS G26 series units are high-efficiency upflow gas furnaces manufactured with DuralokPlust aluminized steel clamshell-type heat exchangers. G26 units are available in heating
TWE+TTA TWE+TWA 6.25-20 T.R.
TWE+TTA TWE+TWA 6.25-20 T.R. Main features : TWE indoor unit : Convertible cabinet, vertical or horizontal. Adjustable speed pulley-belt drive centrifugal fan motor. Aluminium fin coil with copper-tubes.
Split System Heat Pump Product Data
Split System Heat Pump Product Three Phase 4TWA3030A3000C 4TWA3030A4000C 4TWA3036A3000C 4TWA3036A4000C 4TWA3042B3000A 2½ 5 Tons 4TWA3042B4000A 4TWA3048A3000C 4TWA3048A4000C 4TWA3060B3000A 4TWA3060B4000A
How To Install An Evaporator Coil
EVAPORATOR COIL INSTALLATION INSTRUCTIONS EVAPORATOR COIL SAFETY... INSTALLATION REQUIREMENTS... Tools and Parts... System Requirements... Location Requirements... Drain Requirements... INSTALLATION INSTRUCTIONS...
INSTALLATION INSTRUCTIONS
2008 Lennox Industries Inc. Dallas, Texas, USA WARNING Improper installation, adjustment, alteration, service or maintenance can cause property damage, personal injury or loss of life. Installation and
Split System Cooling Product Data
Split System Cooling Product Data Three Phase 4TTA3 2½ 5 Tons PUB. NO. 22-1791-12 Features and Benefits All aluminum Spine Fin coil WeatherGuard fasteners Quick-Sess cabinet, service access and refrigerant
Glossary of Heating, Ventilation and Air Conditioning Terms
Glossary of Heating, Ventilation and Air Conditioning Terms Air Change: Unlike re-circulated air, this is the total air required to completely replace the air in a room or building. Air Conditioner: Equipment
TECHNICAL MANUAL GDS8 & GHS8
TECHNICAL MANUAL AL GDS8 & GHS8 33-3/8" 80% Gas Furnace Units Refer to Service Manual RS6610004 for installation, operation, and troubleshooting information. All safety information must be followed as
48/50EJ,EK,EW,EY038, 044, 048 SINGLE-PACKAGE COOLING UNITS VARIABLE VOLUME CONSTANT VOLUME FACTORY-INSTALLED OPTIONAL HEAT
48/50E-4SB 48/50EJ,EK,EW,EY038, 044, 048 SINGLE-PACKAGE COOLING UNITS VARIABLE VOLUME CONSTANT VOLUME FACTORY-INSTALLED OPTIONAL HEAT GAS HEAT ELECTRIC HEAT PERFORMANCE DATA CERTIFIED DIMENSION PRINT CERTIFIED
XV80 UPFLOW/HORIZONTAL 2-STAGE, VARIABLE SPEED GAS-FIRED FURNACE
UPF/HORIZONTAL 2-, VARIABLE SPEED GAS-FIRED FURNACE XV80 MODELS TUD2B060A9V3VB, TUD2B080A9V3VB TUD2C080A9V4VB, TUD2C080B9V4VB TUD2B00A9V3VB, TUD2C00A9V5VB TUD2C00B9V5VB, TUD2DA9V5VB TUD2DB9V5VB, TUD2DA9V5VB
Low Profile Unit Cooler
Super-Flo Now available with EC Motors High Efficiency / High Reliability Low Profile Unit Cooler Publication No. 411.4 November, 2008 S A N I T A T I O N F O U N D A T I O N A L N A T I O N Air Defrost
INSTALLATION INSTRUCTIONS
2008 Lennox Industries Inc. Dallas, Texas, USA WARNING Improper installation, adjustment, alteration, service or maintenance can cause personal injury, loss of life, or damage to property. Installation
GCS16-024-030-036-048-060
Packaged Unit & Gas Heat 2-5 Ton Capacity 50,000-120,000 Btuh Input Heating Capacity GCS16-024-030-036-048-060 FEATURES Designed for outdoor rooftop or ground level installations Down-flow or horizontal
RHF High Efficiency Remote Heat Pumps and Matching Blower Coils
Heating&Air Conditioning RHF High Efficiency Remote Heat Pumps and Matching Blower Coils Amana RHF heat pumps and matching blower coils offer economy, superior heating and cooling comfort, plus installation
MAC-120HE-01 Air-Cooled Chiller
MAC-120HE-01 Air-Cooled Chiller 10 Ton / 120,000 BTUH Air-Cooled Chiller 208/230-1-50/60 1 HVAC Guide Specifications Air-Cooled Liquid Chiller Nominal Size: 10 Tons Multiaqua Model Number: MAC-120HE-01
Installer s Guide 18-AH39D1-13
18-AH39D1-13 Cased Aluminum "Convertible" Coils 4TXCA018BC3HC** 4TXCA024BC3HC** 4TXCB025BC3HC** 4TXCB026BC3HC** 4TXCB031BC3HC** 4TXCB032BC3HC** ALL phases of this installation must comply with NATIONAL,
Liebert DS Thermal Management Unit
Liebert DS Thermal Management Unit System Design Manual - 28-105kW (8-30 Tons), Downflow/Upflow, 60Hz Floor Mounted, Air-Cooled, Water/Glycol-Cooled, GLYCOOL Economizer Coil, Dual-Cool DX with Secondary
Auxiliary HVAC RAM ProMaster. Standard Tie-in Extreme Climate System
Auxiliary HVAC RAM ProMaster Standard Tie-in Extreme Climate System Auxiliary HVAC High performance aftermarket heating and cooling systems engineered for vehicle specific platforms that minimize install
Explosion-Proof Electric Unit Heaters
Type FX4 FX4 Explosion-Proof Electric Air Heaters FX4 heaters are UL listed and/or CSA certified for use in hazardous locations. They are designed for dry indoor industrial applications such as oil refineries,
Installation Instructions
H5HK Series Installation Instructions 3 Phase Electric Heater Kits 7.5 and 0 TON Package A/C Systems Description Installation of 08/40V and 480V H5HK 3 Phase Heater Kits in 7.5 and 0 TON Packaged Air Conditioners.
ARUF Series. Multi-Position, Multi-speed Air Handler with PSC Motor 1½ to 5 Tons. Contents. Product Features
Series Multi-Position, Multi-speed Air Handler with PSC Motor 1½ to 5 Tons Contents Nomenclature... 2 Product Specifications... 3 Heater Kit Nomenclature... 3 Dimensions... 4 Airflow Data... 5 Heat Kit
LH and GH/GL Series UNIT COOLERS. Technical Bulletin: LHGH_001_071015. Products that provide lasting solutions.
LH and GH/GL Series UNIT COOLERS Technical Bulletin: LHGH_001_07101 Products that provide lasting solutions. LH Series Unit Coolers Dual Discharge Low Hite Series At 9 1/ maximum height, the LH Series
Evaporator Coil Installation Instructions
Part # 96654008 July 2010 Evaporator Coil Installation Instructions A-Coil Page 4 Multi-position A-Coil Page 4-7 Slab Coil Page 5 Horizontal A-Coil Top Connection Page 5 Horizontal A-Coil Side Connection
WMSLW / WMBLWH Series Hydronic Upflow/Horizontal Left or Right, Heating and Cooling Air Handler
WMSLW / WMBLWH Series Hydronic Upflow/Horizontal Left or Right, Heating and Cooling Air Handler Installation Operation Maintenance The WMSLW/WMBLW series is designed for installation in a closet, utility
ModPac II 1 to 5-Ton Vertical Wall Mount Air Conditioners Models AVPA12-20-24-30-36-42-48-60
ModPac II 1 to 5-Ton Vertical Wall Mount Air Conditioners Models AVPA12-20-24-30-36-42-48-60 General Description The Marvair ModPac II air conditioner is a vertical, wall mounted, cost effective air conditioner
Submitted to Reference Approval Construction Unit Designation Schedule #
SUBMITTAL AQV09JA High Wall 9,000 Btu/h Heat Pump Nom Cooling Capacity (Btu/h) 9,000 SEER 20.0 Cool Capacity Range (Btu/h) 3,100 to 11,900 Nom Heating Capacity (Btu/h) 11,950 HSPF 10.0 Heating COP 3.7
XV 95. Upflow/ Horizontal Left, Downflow/ Horizontal Right Variable Speed Two Stage Condensing Gas-Fired Furnace PUB. NO.
Upflow/ Horizontal Left, Downflow/ Horizontal Right Speed Two Stage Condensing Gas-Fired Furnace XV 95 TUH2B060A9V3VB TUH2B080A9V3VB TUH2B080A9V4VB TUH2C100A9V4VB TUH2C100A9V5VB TUH2D120A9V5VB Direct Vent
AVPTC. Multi-Position, Variable-Speed ECM Based Air Handler with Internal TXV Comfortnet Compatible 1½ to 5 Tons. Contents.
Multi-Position, Variable-Speed ECM Based Air Handler with Internal TXV Comfortnet Compatible 1½ to 5 Tons Contents Air Handler Nomenclature... Heater Kit Nomenclature... Product Specifications... 3 Dimensions...
Installation Manual CLIFC Fan & Coil Variable Speed
Installation Manual CLIFC Fan & Coil Variable Speed General Description GENERAL DESCRIPTION FANS EQUIPMENT Totally Factory assembled within the unit all piping, wiring, and required controls for operation
Installation Manual. Rental Services. Air Handling Units CHS-SVN01A-EN. July 2008
Installation Manual Rental Services Air Handling Units July 2008 CHS-SVN01A-EN Copyright 2008 Trane All rights reserved This document and the information in it are the property of Trane and may not be
Single Package Vertical Air Conditioners. Vert-I-Pak
Single Package Vertical Air Conditioners Vert-I-Pak Installs easily in a closet for quiet operation and provides a more homelike appearance for your guests. THE EXPERTS IN ROOM AIR CONDITIONING A Better
SINGLE PACKAGE VERTICAL AIR CONDITIONERS
SINGLE PACKAGE VERTICAL AIR CONDITIONERS AIR CONDITIONERS l HEAT PUMPS l ELECTRIC HEAT QUIETER BY DESIGN SIMPLE TO INSTALL CONCEALED INSTALLATION www.friedrich.com VERT-I-PAK ideal for extended stay properties,
INSTALLER'S GUIDE. Supplementary Electric Heaters 18-GJ08D1-1. Table of Contents
INSTALLER'S GUIDE ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES Models: BAYEAAC051A BAYEAAC05LG1A BAYEAAC081A BAYEAAC08LG1A BAYEAAC101A BAYEAAC10LG1A BAYEABC151A BAYEABC201A
york air-conditioning products Residential & VRF News 2015
york air-conditioning products Residential & VRF News 2015 york air-conditioning products Catalogue Content Split Systems Pag. High wall High Efficiency Inverter YWHJZH 09 to 24 K 6 High wall Inverter
Gas Unit Heaters Duct Furnaces Horizontal - 60 HZ Form No. LF24-100-400 (10/2011) LF24 Standard
LF Standard Features Horizontal unit heaters are compact in design and easy to install. Steady State Efficiencies of up to 80.%. Ideal for economical commercial heating systems. Shipped completely assembled
IMPORTANT: BEFORE INSTALLING ANY HEATING TERMINAL UNIT TO A DOMESTIC WATER HEATER, CONSULT THE LOCAL PLUMBING CODES.
QUIET-ONE Environmental Products 2000 Kickspace Heater Series Models: KS 2004, KS 2006 KS 2008, KS 2010 INSTALLATION OPERATING MAINTENANCE Please read these instructions thoroughly before beginning your
Evaporator Coils. Upflow/Downflow Vertical N-Coil Transition Upflow/Downflow N-Coil Horizontal N-coil. Upflow/Downflow Uncased Vertical N-Coil
Upflow/Downflow Vertical N-Coil Transition Upflow/Downflow N-Coil Horizontal N-coil Upflow/Downflow Uncased Vertical N-Coil Upflow/Downflow Uncased A-Coil Slab Coil Cased Horizontal 50 51 Payne Upflow/Downflow
SPACE COOLERS. P.O. Box 956 Paoli, PA 19301 (800) 523-7590 FAX (610) 251-0805 www.coilcompany.com. The leader in packaged Space Cooling.
SPACE COOLERS P.O. Box 956 Paoli, PA 19301 (800) 523-7590 FAX (610) 251-0805 www.coilcompany.com The leader in packaged Space Cooling. 2 Table of Contents Description Space Cooler from Coil Company. A
AIR-COOLED CONDENSERS Technical Guide
BN-ACCTB0306 March, 2006 AIR-COOLED CONDENSERS Technical Guide Monarch and Ambassador Series TABLE OF CONTENTS Overview... 2, 3 Features & Options... 3, 4 Three Solutions...5 Nomenclature...6 Condenser
Product Data. FX4D Comfort Series Fan Coil Sizes 019 thru 061 AIR HANDLER TECHNOLOGY AT ITS FINEST
Comfort eries Fan Coil izes 019 thru 061 Product Data AIR HANDLER TECHNOLOGY AT IT FINET The fan coils combine the proven technology of Carrier fan coil units with Puron, the environmentally sound refrigerant.
ENGINEERING GUIDE. Water-Cooled Self-Contained Units C-Series, Vertical
ENGINEERING GUIDE Water-Cooled Self-Contained Units C-Series, Vertical TABLE OF CONTENTS Introduction...2 Product Overview...3 Nomenclature...4 General Data...5 Cooling Performance Data....6 Evaporator
HA HE Series. Solutions for Your needs. fl exible and confi gure-to-order coils. Healthy Solutions coils
Series air handlers evaporator coils HA HE Series Healthy Solutions coils unit heaters fl exible and confi gure-to-order coils Solutions for Your needs our features. your benefits. Easy Installation and
SECTION 15732 AIR CONDITIONING UNIT
SECTION 15732 AIR CONDITIONING UNIT PART 1 GENERAL 1.01 SUMMARY A. Section includes: 1. Packaged, split system air conditioning unit No. 1. 1.02 REFERENCES A. Air-Conditioning, Heating, and Refrigeration
ECOCIAT. Domestic hot water heat recovery unit
Heat recovery unit Domestic hot water High energy efficiency with R410A Compact and quiet Scroll compressors Brazed-plate heat exchangers Heating Heat recovery ENVIRONMENTALLY HFC R410A PROTECTION DE FRIENDLY
C26 Bulletin #210061 November 1997 Supersedes January 1997 (Coil/Furnace Match Up Charts)
NGINRING T loset Installation With Pulse21 Furnace and lectronic ir leaner Typical pplications UNS N FULL S UP- VPORTOR OILS IR-ONITIONING N HT PUMP 2 To 5 Ton (7.0 To 17.6 kw) Nominal Size OILS LOWR OILS
Product Data. Split System Cooling 22-1904-1F-EN. March 2015
Product Data Split System Cooling 4TTR4018L1000A 4TTR4024L1000A 4TTR4025L1000A 4TTR4030L1000A 4TTR4031L1000A 4TTR4036L1000A 4TTR4037L1000A 4TTR4042L1000A 4TTR4043L1000A 4TTR4048L1000A 4TTR4060L1000A Note:
SECTION 23 81 03 - PACKAGED ROOFTOP AIR CONDITIONING UNITS NON-CUSTOM
SECTION 23 81 03 - PACKAGED ROOFTOP AIR CONDITIONING UNITS NON-CUSTOM PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Packaged rooftop air conditioning unit (5 tons and smaller). 2. Roof curb. 1.2
AquaFREE System. Technical Catalogue. Outdoor units: RAS-(3~5)HVRNE RAS-(4/5)HRNE. Indoor units: RWM-(3~5)FSN1E RWM-(3~5)FSN1E-(4.
AquaFREE System Technical Catalogue Outdoor units: RAS-(3~5)HVRNE RAS-(4/5)HRNE Indoor units: RWM-(3~5)FSN1E RWM-(3~5)FSN1E-(4.5/6)H(1/3) Specifications in this manual are subject to change without notice
Residential/Commercial Gas Condensing High Efficiency Tankless Water Heaters
Residential/Commercial Gas Condensing High Efficiency Tankless Water Heaters FEATURES ULTRA-LOW NOx CONDENSING TECHNOLOGY PROVIDES UNPRECEDENTED 0.95 ENERGY FACTOR DURABLE HEAT EXCHANGER Primary Heat Exchanger
VertiCool Space Saver 2 to 15 tons Water-Cooled and Chilled Water
2 to 15 tons Water-Cooled and Chilled Water Unique Solutions for Challenging HVAC Projects Your Choice for Limited Space Applications Water-Cooled Chilled Water The VertiCool Space Saver allows installation
catalog Single Package Vertical Air Conditioners and Heat Pumps
catalog Single Package Vertical Air Conditioners and Heat Pumps Catalog: SK145.00-EG1 (1008) TABLE OF CONTENTS Single Package Vertical Units Introduction...............................................................................
26 AND 27 SLEEVES. IDEAL for NEW CONSTRUCTION, RETROFITS and REMODELS.
T H R U - T H E - W A L L A I R C O N D I T I O N E R S 26 AND 27 SLEEVES. IDEAL for NEW CONSTRUCTION, RETROFITS and REMODELS. W A L L M A S T E R T H R U - T H E - W A L L A I R C O N D I T I O N E R
Element D Services Heating, Ventilating, and Air Conditioning
PART 1 - GENERAL 1.01 OVERVIEW A. This section supplements Design Guideline Element D3041 on air handling distribution with specific criteria for projects involving design of a Data Center spaces B. Refer
DUCTLESS MINI-SPLITS SINGLE & MULTI-ZONE HORIZONTAL AIR CONDITIONERS PORTABLE UNITS FREE MATCH COMPONENTS
DUCTLESS MINI-SPLITS SINGLE & MULTI-ZONE HORIZONTAL AIR CONDITIONERS PORTABLE UNITS FREE MATCH COMPONENTS AN EXCELLENT CHOICE IN COOLING, COMFORT AND CONVENIENCE Why choose a Mini-Split system? Installing
INSTALLATION AND OPERATION INSTRUCTIONS - (LOW FLOW MODELS) (Before installation, compare electrical needed for the model of heater selected)
CHRONOMITE INSTANT-FLOW WATER HEATER INSTALLATION AND OPERATION INSTRUCTIONS - (LOW FLOW MODELS) (Before installation, compare electrical needed for the model of heater selected) TABLE 1 Model No. Wattage
CASED & UNCASED UPFLOW & DOWNFLOW EVAPORATOR COILS
CASED & UNCASED UPFLOW & DOWNFLOW EVAPORATOR COILS Description / Application Compact, versatile, right or left horizontal position May be used in closet, utility room, or basement Standard Finish Fully
TABLE 1. Rugged cast aluminum alloy casing,celcon waterways with nichrome parts White (unless stainless steel housing)
CHRONOMITE INSTANT-FLOW MICRO WATER HEATER INSTALLATION AND OPERATION INSTRUCTIONS - (LOW FLOW MODELS) (Before installation, compare electrical needed for the model of heater selected) TABLE 1 Model No.
SECTION 23 81 43 HEAT PUMPS
SECTION 23 81 43 HEAT PUMPS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Packaged rooftop heat pumps. 1.2 REFERENCES A. American Society of Heating, Refrigerating and Air-Conditioning Engineers:
Operation and Installation Manual. Max Series
Operation and Installation Manual Max Series Models 95MAX 155MAX 155ECM 155MAXRX 200MAX 200MAXRX MAXTOP 195DCS 300DCS 200ERV 200ERVD New Auto Dehumidistat Function prevents unwanted use of the dehumidistat
CAB LCAB HACAB RMP/AMP CC CY/YY RVP CUSTOM CU
GENERAL PURPOSE (ORDINARY) LOCATION Custom Controls provides the petro-chemical and offshore industries with HVAC equipment of the highest quality and reliability on the market at an economical price.
FTQ. Daikin Inverter Ducted Heat Pump
FTQ Daikin Inverter Ducted Heat Pump A TRADITIONAL CENTRAL AIR SYSTEM MADE BETTER WITH DAIKIN CONSTANT COMFORT INVERTER TECHNOLOGY. The Daikin Inverter Ducted Heat Pump line is a cost effective alternative
Evaporator Coil. Installation Instructions GENERAL
IM-HAC-0966540-12 December 2013 Evaporator Coil Installation Instructions TABLE OF CONTENTS PAGE General... 1 Vertical... 2 Horizontal... 2 Multi-Position... 3-5 Metering Device... 6 Condensate Drain...
Installation Instructions
05,06 Single Package, Displacement Ventilation or Single Zone Variable Airflow Rooftop Units Electric Cooling with PURONr (R---410A) Refrigerant and COMFORTLinkt Controls Installation Instructions IMPORTANT:
3Aftermarket Systems. Air Conditioners and Kombos.. 411. Heater/Pressurizer...440. System Matrix...441. Aftermarket System Requirements...
3Aftermarket Systems Air Conditioning & Heating Replacement Parts Aftermarket Systems Air Conditioners and Kombos.. 411 KA-300 Air Conditioner... 411 KK-315 Heater/Air Conditioner Kombo...412 KA-400 Air