Schulte-Schlagbaum AG Next level access since 1833 Product catalogue SAFE-O-TRONIC access Door and furniture locking systems SAFE-O-TRONIC access Product catalogue
SAFE-O-TRONIC access Electronic Identification and Locking System SAFE-O-TRONIC access DS SAFE-O-TRONIC access DS-T SAFE-O-TRONIC access CS SAFE-O-TRONIC access LS SAFE-O-TRONIC access TS Door locking systems Furniture locking systems Terminals Notes about this product catalogue Copyright 2013 by Schulte-Schlagbaum AG Nevigeser Straße 100-110 42553 Velbert, Germany Telephone: +49 2051 2086-0 http:/www.sag-schlagbaum.com Issue date: 20130402 Version: 1.0 Document number: SAFE-O-TRONIC Product catalogue SAFE-O-TRONIC access_v2 20130402.docx is a registered trademark of Schulte-Schlagbaum AG.
Contents Door locking systems SAFE-O-TRONIC access DS Fitting sets...08 Customisation...16 Accessories...17 Mechanical locking cylinders...19 Fitting accessories...20 Furniture locking systems SAFE-O-TRONIC access LS...74 Customisation...82 Accessories...83 Overview...84 Terminals SAFE-O-TRONIC access TS...88 SAFE-O-TRONIC access DS-T...28 Customisation...34 Accessories...35 Fittings...36 Fitting accessories...43 Overview...46 SAFE-O-TRONIC access CS...50 Accessories...58 Fittings...60 Fitting accessories...67 Overview...70 Additional components Programming accessories...100 Software...104 RFID data carriers...108 01
SAFE-O-TRONIC access Electronic Identification and Locking System Architecture and technology All components of the SAFE-O-TRONIC access locking system were integrated in a standardised and consistent product line. Product line The following systems belong to the SAFE-O- TRONIC access product line:, SAFE-O-TRONIC access DS door locking system, SAFE-O-TRONIC access CS cylinder locking system, SAFE-O-TRONIC access LS furniture locking system, SAFE-O-TRONIC access TS terminal system. The design is consistent and function-orientated and the programming concept is also consistent. Identification PIN code and RFID technologies are combined for SAFE-O-TRONIC access locking systems. With the integration of NFC technology, a mobile telephone can also be used as the key for SAFE-O-TRONIC access locking systems. Standards SAFE-O-TRONIC access DS is approved for use on fire and smoke protection doors as well as for emergency exit locks according to DIN EN 179. SAFE-O-TRONIC access CS is also approved according to DIN EN 179 and DIN EN 1125. All locking systems meet electromagnetic compatibility (EMC) requirements and are CE compliant. 02
SAFE-O-TRONIC access system landscape Door locking systems Furniture locking systems Terminals 03
SAFE-O-TRONIC access Electronic Identification and Locking System Design and organisation Customisation In 2010, 2011 and 2012 SAFE-O-TRONIC access locking systems were awarded various design awards. With the customisation option, the furniture and door closing systems can be integrated into many different architecture and design concepts. SAFE-O- TRONIC access DS locking systems can be combined with various door handles and rosettes. The front panel and ornamental handle rosettes can be designed freely. Card-based network With the optional use of a virtual card-based network, SAFE-O-TRONIC access CyberNet, SAFE-O- TRONIC access offline locking systems are equipped with the convenience of online locking systems. Benefits at a glance: When commissioning the locking system:, Simple and convenient programming of the offline locking systems on the PC - without inspecting the doors or cupboards, Automatic programming of existing passes When running:, Simple and convenient locking system management on the PC without wiring to the doors and furniture, Simple changes / updates of the locking authorisations of the individual users on the PC, Fast response for card loss, Simple coding and issue of new passes for employees or visitors, Simple integration into existing online access control systems, Online logging of all actions at the CyberSpots, High level of flexibility: up to 4,000 different locking authorisations (lock groups) can be set up. Integration The integration of SAFE-O-TRONIC access locking systems into existing systems or planned data systems, e.g. front office systems, guest management systems or time recording systems is possible at any time. XML and CSV interfaces for data exchange and various software tools are available for integration. 04
Customisation SAFE-O-TRONIC CyberNet card-based network Access control Personnel time recording Cashless settlement EtherNet CyberNet data exchange by RFID data carriers 05
06
Door locking systems SAFE-O-TRONIC access DS 07
SAFE-O-TRONIC access DS door locking system Fitting sets SAFE-O-TRONIC access DS200 PIN code door locking system for integrating into a lever handle Locking unit with PIN code function as well as RFID programming and RFID master key function, capacitive keypad, matt stainless steel housing. The free-running door handle is coupled so that the falling latch of the mortise lock can be actuated. SAFE-O-TRONIC access DS200 is for universal use in right and left hand doors. Installation on doors with mortise locks according to DIN 18251, for fire protection doors according to DIN FS 18273 and regardless of the distance. Award winning locking system: if product design award 2011 and nominated for "Designpreis Deutschland 2012" Door thickness between 38 and 86 08
Technical specifications, Dimensions (HxWxD): 204mm x 55mm x 21mm (not including door handle), Weight (not including door handle): approx. 600g, Housing surface: matt stainless steel, standard alkaline batteries on the outside of the door, battery life: approx. 3 years or approx. 30,000 actuations, protection class IP 43 according to DIN EN 60529, door thickness from 38 to 86mm, other door thicknesses optional, operating temperature range: 0 to +60 C, storage temperature range: -15 to +70 C, relative humidity: 10 90% non-condensing SAFE-O-TRONIC access DS200 is available in the following models: # 50201.2DR-3 with stainless steel lever handle aperture on the outside and stainless steel lever handle aperture with rosette on the inside, L-shape class 3, with substructure made of fibre glass reinforced plastic on the inside of the door and holding spring, firmly pivoted, with twopart round cover and PZ rosettes and invisible attachment. # 50201.2DR-4 with stainless steel lever handle aperture on the outside and stainless steel lever handle aperture with rosette on the inside, L-shape class 4, with steel substructure on the inside of the door, precision ball bearings, with one-part round cover and PZ rosette and invisible attachment. # 50201.2FS with stainless steel lever handle aperture on the outside and stainless steel lever handle aperture with rosette on the inside, L-shape class 4 FS, with steel substructure on the inside of the door, precision ball bearings, with one-part round cover and PZ rosette and invisible attachment for fire protection doors according to DIN FS 18273. Optional: U-shaped door handle model 202 or model 209 Optional: U-shaped door handle model 202 or model 209 Classification code according to DIN EN 1906: 3 7-0 1 4 0 U Classification code according to DIN EN 1906: 4 7 - C1 1 4 0 U Classification code according to DIN EN 1906: 4 7 - C1 1 4 0 U 09
SAFE-O-TRONIC access DS door locking system Fitting sets SAFE-O-TRONIC access DS300 RFID door locking system for integrating into a lever handle Locking unit with RFID function, with contactless alarm sensor, matt stainless steel housing. The free-running door handle is coupled so that the falling latch of the mortise lock can be actuated. SAFE-O-TRONIC access DS300 is for universal use in right and left hand doors. Installation on doors with mortise locks according to DIN 18251, for fire protection doors according to DIN FS 18273 and regardless of the distance. Award winning locking system: if product design award 2011 and nominated for "Designpreis Deutschland 2012" Door thickness between 38 and 86 10
Technical specifications, Dimensions (HxWxD): 204mm x 55mm x 21mm (not including door handle), Weight (not including door handle): approx. 600g, housing surface: matt stainless steel, standard alkaline batteries on the outside of the door, battery life: approx. 3 years or approx. 30,000 actuations, protection class IP 43 according to DIN EN 60529, door thickness from 38 to 86mm, other door thicknesses optional, operating temperature range: 0 to +60 C, storage temperature range: -15 to +70 C, relative humidity: 10 90% non-condensing SAFE-O-TRONIC access DS300 is available in the following models: # 50201.3DR-3 with stainless steel lever handle aperture on the outside and stainless steel lever handle aperture with rosette on the inside, L-shape class 3, with substructure made of fibre glass reinforced plastic on the inside of the door and holding spring, firmly pivoted, with twopart round cover and PZ rosettes and invisible attachment. # 50201.3DR-4 with stainless steel lever handle aperture on the outside and stainless steel lever handle aperture with rosette on the inside, L-shape class 4, with steel substructure on the inside of the door, precision ball bearings, with one-part round cover and PZ rosette and invisible attachment. # 50201.3FS with stainless steel lever handle aperture on the outside and stainless steel lever handle aperture with rosette on the inside, L-shape class 4 FS, with steel substructure on the inside of the door, precision ball bearings, with one-part round cover and PZ rosette and invisible attachment for fire protection doors according to DIN FS 18273. Optional: U-shaped door handle model 202 or model 209 Optional: U-shaped door handle model 202 or model 209 Classification code according to DIN EN 1906: 3 7-0 1 4 0 U Classification code according to DIN EN 1906: 4 7 - C1 1 4 0 U Classification code according to DIN EN 1906: 4 7 - C1 1 4 0 U 11
SAFE-O-TRONIC access DS door locking system Fitting sets SAFE-O-TRONIC access DS300 DND RFID door locking system with do not disturb function for integrating into a lever handle Locking unit with RFID and do not disturb function, with contactless alarm sensor, matt stainless steel housing. The free-running door handle is coupled so that the falling latch of the mortise lock can be actuated. Installation on doors with mortise locks according to DIN 18251, for fire protection doors according to DIN FS 18273 and regardless of the distance. Award winning locking system: if product design award 2011 and nominated for "Designpreis Deutschland 2012" Door thickness between 38 and 86 12
Do not disturb function: For guest room doors, SAFE-O-TRONIC access DS300 DND provides the option of excluding undesired access while the room is occupied. Technical specifications, Dimensions (HxWxD): 204mm x 55mm x 21mm (not including door handle), Weight (not including door handle): approx. 600g, housing surface: matt stainless steel, standard alkaline batteries on the outside of the door, battery life: approx. 3 years or approx. 30,000 actuations, protection class IP 43 according to DIN EN 60529, door thickness from 38 to 86mm, other door thicknesses optional, operating temperature range: 0 to +60 C, storage temperature range: -15 to +70 C, relative humidity: 10 90% non-condensing SAFE-O-TRONIC access DS300 DND is available in the following models: # 50201.3DR DND with stainless steel lever handle aperture on the outside and do not disturb inner sign L-shape class 4. Fire protection design according DIN 18273. Optional: U-shaped door handle model 202 or model 209 Classification code according to DIN EN 1906: 4 7 - C1 1 5 4 U 13
SAFE-O-TRONIC access DS door locking system Fitting sets SAFE-O-TRONIC access DS400 RFID / PIN code door locking system for integrating into a lever handle Locking unit with PIN code and RFID function, with contactless alarm sensor, matt stainless steel housing. The free-running door handle is coupled so that the falling latch of the mortise lock can be actuated. SAFE-O-TRONIC access DS400 is for universal use in right and left hand doors. Installation on doors with mortise locks according to DIN 18251, for fire protection doors according to DIN FS 18273 and regardless of the distance. Award winning locking system: if product design award 2011 and nominated for "Designpreis Deutschland 2012" Door thickness between 38 and 86 14
Technical specifications, Dimensions (HxWxD): 204mm x 55mm x 21mm (not including door handle), Weight (not including door handle): approx. 600g, housing surface: matt stainless steel, standard alkaline batteries on the outside of the door, battery life: approx. 3 years or approx. 30,000 actuations, protection class IP 43 according to DIN EN 60529, door thickness from 38 to 86mm, other door thicknesses optional, operating temperature range: 0 to +60 C, storage temperature range: -15 to +70 C, relative humidity: 10 90% non-condensing SAFE-O-TRONIC access DS400 is available in the following models: # 50201.4DR-3 with stainless steel lever handle aperture on the outside and stainless steel lever handle aperture with rosette on the inside, L-shape class 3, with substructure made of fibre glass reinforced plastic on the inside of the door and holding spring, firmly pivoted, with two-part round cover and PZ rosettes and invisible attachment. # 50201.4DR-4 with stainless steel lever handle aperture on the outside and stainless steel lever handle aperture with rosette on the inside, L-shape class 4, with steel substructure on the inside of the door, precision ball bearings, with one-part round cover and PZ rosette and invisible attachment. # 50201.4FS with stainless steel lever handle aperture on the outside and stainless steel lever handle aperture with rosette on the inside, L-shape class 4 FS, with steel substructure on the inside of the door, precision ball bearings, with one-part round cover and PZ rosette and invisible attachment for fire protection doors according to DIN FS 18273. Optional: U-shaped door handle model 202 or model 209 Optional: U-shaped door handle model 202 or model 209 Classification code according to DIN EN 1906: 3 7-0 1 4 0 U Classification code according to DIN EN 1906: 4 7 - C1 1 4 0 U Classification code according to DIN EN 1906: 4 7 - C1 1 4 0 U 15
SAFE-O-TRONIC access DS door locking system Customisation Printing on front panel with motif (such as logo, graphic or lettering) Printing on front panel for all locks in the system. SAFE-O-TRONIC access DS door locking systems can be designed with a customised pictorial motif as an option. # 384DL2001 Restricted area Foreground Restricted area Foreground Print area Print area Transparent Transparentarea Printed on the back 16
Accessories Decorative lever handle rosette made of wood Decorative lever handle rosette for customisation. With the easily replaceable decorative wooden lever handle rosettes, the SAFE-O-TRONIC access DS door locking system matches the appearance of the door leaf. # 50299530 Light beech # 50299531 Black beech # 50299532 Oak 17
SAFE-O-TRONIC access DS door locking system Accessories Battery pack # 38400200 Battery pack, consisting of 3 standard alkaline batteries, for SAFE-O-TRONIC access DS, DS-T and LS. Battery life: approx. 3 years or approx. 30,000 actuations 18
Mechanical locking cylinders Mechanical locking cylinder 6-pin system for use as emergency cylinder for SAFE-O-TRONIC access DS # 50204WDZ Mechanical locking double cylinder 030/030, HS, including 3 individual keys, extension up to a total length of 80mm per side possible # 50204WHZ Mechanical locking half cylinder 000/030, HS, including 3 individual keys, extension up to a total external length of 80mm possible # 50204WKZ Mechanical knob half cylinder 000/030, HS, including 3 individual keys, extension up to a total external length of 80mm possible # 50204WHS Master key (HS) 19
SAFE-O-TRONIC access DS door locking system Fitting accessories Lever handles (individual parts), model 203 Matt stainless steel surface # 50299550H L-shaped lever handle aperture, Model 203, 8mm, Class 3 outer lever handle aperture # 50299561H L-shaped lever handle aperture, Model 203, 9mm, Class 4, FS outer lever handle aperture # 50299552H L-shaped lever handle aperture with rosette, Model 203, 8mm, Class 3 lever handle aperture including inner lever handle rosette # 50299553H L-shaped lever handle aperture with rosette, Model 203, 9mm, Class 4, FS lever handle aperture including inner lever handle rosette 20
Lever handles (individual parts), model 202 Matt stainless steel surface # 50299562H U-shaped lever handle aperture, Model 202, 9mm, Class 4, FS outer lever handle aperture # 50299564H U-shaped lever handle aperture with rosette, Model 202, 8mm, Class 4 lever handle aperture including inner lever handle rosette # 50299565H U-shaped lever handle aperture with rosette, Model 202, 9mm, Class 4, FS lever handle aperture including inner lever handle rosette 21
SAFE-O-TRONIC access DS door locking system Fitting accessories Lever handles (individual parts), model 209 Matt stainless steel surface # 50299563H U-shaped lever handle aperture, Model 209, 9mm, Class 4, FS outer lever handle aperture # 50299566H U-shaped lever handle aperture with rosette, Model 209, 8mm, Class 4 lever handle aperture including inner lever handle rosette # 50299567H U-shaped lever handle aperture with rosette, Model 209, 9mm, Class 4, FS Lever handle aperture including inner lever handle rosette 22
Rosettes to complement SAFE-O-TRONIC access DS fitting sets Matt stainless steel surface # 50299507 Rosette set 1 Model: Stainless steel, blind blind covering blind substructure PC punch hole # 50299508 Rosette set 2 Model: Stainless steel, PC punch hole cover PC punch hole substructure PC punch hole # 50299509 Rosette set 3 Model: Stainless steel, blind covering PC punch hole, blind substructure PC punch hole Rosette set 1 Rosette set 2 Rosette set 3 23
SAFE-O-TRONIC access DS door locking system Fitting accessories Rosettes to complement SAFE-O-TRONIC access DS fitting sets Matt stainless steel surface # 50299510 Rosette set 4 Model: Stainless steel, blind covering blind covering, PC punch hole substructure PC punch hole # 50299511 Rosette set 5 Model: Stainless steel, blind covering PC punch hole, PC punch hole substructure PC punch hole # 50299512 Rosette set 6 Model: Stainless steel, blind rotary knob covering, blind substructure PC Punch hole. Use as internal locking for DS with profile adapter Rosette set 4 Rosette set 5 Rosette set 6 24
Decorative plates (renovation plates) for renovation Matt stainless steel material, 1.5mm thick # 50299600A Decorative plate set model A gap 70 78mm, including PC punch hole, inside and outside, for DS # 50299600B Decorative plate set model B gap 85 92mm, including PC punch hole, inside and outside, for DS Decorative plate set model A (left: outside - right: inside) Decorative plate set model B (left: outside - right: inside) 25
SAFE-O-TRONIC access DS door locking system Fitting accessories Decorative plates (renovation plates) for renovation Matt stainless steel material, 1.5mm thick # 50299600C Decorative plate set model C any gap, blind bottom, inside and outside, for DS # 50299600D Decorative plate model D retrofitting VARIFLEX model hotel, outside only, for DS Decorative plate set model C (left: outside - right: inside) Decorative plate set model D (outside) 26
Door locking systems SAFE-O-TRONIC access DS-T 27
SAFE-O-TRONIC access DS-T door locking system SAFE-O-TRONIC access DS-T200 PIN code door locking system with rotary knob for actuating a bolt Locking unit with PIN code function as well as RFID programming and RFID master key function, capacitive keypad, matt stainless steel housing. The free-running rotary knob is coupled so that the dead bolt of the mortise lock can be actuated. SAFE-O-TRONIC access DS-T200 for universal use in left and right hand doors. This model provides additional locking security compared with SAFE-O-TRONIC access DS. Award winning locking system: if product design award 2011 and nominated for "Designpreis Deutschland 2012" Door thickness between 38 and 86 28
Technical specifications, Dimensions (HxWxD): 204mm x 55mm x 46mm, Weight: approx. 600g, Housing surface: matt stainless steel, standard alkaline batteries on the outside of the door, battery life: approx. 3 years or approx. 30,000 actuations, protection class IP 43 according to DIN EN 60529, door thickness from 38 to 86mm, other door thicknesses optional, operating temperature range: 0 to +60 C, storage temperature range: -15 to +70 C, relative humidity: 10 90% non-condensing SAFE-O-TRONIC access DS-T200 is available in the following models: # 50202.2DK with internal locking with rotary knob rosette. The fitting set is available as an option. # 50202.2FS with internal locking with rotary knob rosette, in FS design. The fitting set is available as an option. 29
SAFE-O-TRONIC access DS-T door locking system SAFE-O-TRONIC access DS-T300 RFID door locking system with rotary knob for actuating a bolt Locking unit with RFID function, with contactless alarm sensor, matt stainless steel housing. The free-running rotary knob is coupled so that the dead bolt of the mortise lock can be actuated. SAFE-O-TRONIC access DS-T300 for universal use in right and left hand doors. This model provides additional locking security compared with SAFE-O-TRONIC access DS. Award winning locking system: if product design award 2011 and nominated for "Designpreis Deutschland 2012" Door thickness between 38 and 86 30
Technical specifications, Dimensions (HxWxD): 204mm x 55mm x 46mm, weight: approx. 600g, housing surface: matt stainless steel, standard alkaline batteries on the outside of the door, battery life: approx. 3 years or approx. 30,000 actuations, protection class IP 43 according to DIN EN 60529, door thickness from 38 to 86mm, other door thicknesses optional, operating temperature range: 0 to +60 C, storage temperature range: -15 to +70 C, relative humidity: 10 90% non-condensing SAFE-O-TRONIC access DS-T300 is available in the following models: # 50202.3DK with internal locking with rotary knob rosette. The fitting set is available as an option. # 50202.3FS with internal locking with rotary knob rosette. The fitting set is available as an option. 31
SAFE-O-TRONIC access DS-T door locking system Versions SAFE-O-TRONIC access DS-T400 RFID / PIN code door locking system with rotary knob for actuating a bolt Locking unit with PIN code and RFID function, with rotary knob for actuating a bolt, with contactless alarm sensor, matt stainless steel housing. The free-running rotary knob is coupled so that the dead bolt of the mortise lock can be actuated. SAFE-O-TRONIC access DS-T400 for universal use in right and left hand doors. This model provides additional locking security compared with SAFE-O-TRONIC access DS. Award winning locking system: if product design award 2011 and nominated for "Designpreis Deutschland 2012" Door thickness between 38 and 86 32
Technical specifications, Dimensions (HxWxD): 204mm x 55mm x 46mm, Weight: approx. 600g, Housing surface: matt stainless steel, Standard alkaline batteries on the outside of the door, Battery life: approx. 3 years or approx. 30,000 actuations, Protection class IP 43 according to DIN EN 60529, Door thickness from 38 to 86mm, other door thicknesses optional, Operating temperature range: 0 to +60 C, Storage temperature range: -15 to +70 C, Relative humidity: 10 90% non-condensing SAFE-O-TRONIC access DS-T400 is available in the following versions: # 50202.4DK with internal locking with rotary knob rosette. The fitting set is available as an option. # 50202.4FS with internal locking with rotary knob rosette. The fitting set is available as an option. 33
SAFE-O-TRONIC access DS-T door locking system Customisation Printing on front panel with motif (such as logo, graphic or lettering) Printing on front panel for all locks in the system. SAFE-O-TRONIC access DS door locking systems can be designed with a customised pictorial motif as an option. # 384DL2001 Templates: PDF file and also a CorelDraw (12 or 14) and /or DXF file Transparent Transparent Print area Print area Restricted area Foreground Restricted area Foreground DS-T300 DS-T200 DS-T400 34
Accessories Battery pack # 38400200 Battery pack, consisting of 3 standard alkaline batteries, for SAFE-O-TRONIC access DS, DS-T and LS. Battery life: approx. 3 years or approx. 30,000 actuations. 35
SAFE-O-TRONIC access DS-T door locking system Fittings Fittings model 203 / 820 Fittings in the form of lever handle fittings L-shaped model 203 and security lever fittings with lever handle aperture with rosette model 203 and fixed knob model 820, surface: matt stainless steel. 36
Lever handle lever handle Lever handle knob # 50202.Dx32038 Lever handle L-shaped lever handle, 8mm, Class 3 Lever handle apertures with rosette model 203 for inside and outside, includes square pin and fastening hardware # 50202.Dx42038 Lever handle L-shaped lever handle, 8mm, Class 4 Lever handle apertures with rosette model 203 for inside and outside, includes square pin and fastening hardware # 50202.Dx42039 Lever handle L-shaped lever handle, 9mm, Class 4, FS lever handle apertures with rosette model 203 for inside and outside, in fire protection version including square pin and fastening hardware # 50202.Wx32038 L-shaped lever handle knob, 8mm, Class 3 Fixed knob Model 820 outside and lever handle aperture with rosette model 203, inside, including square pin and fastening hardware # 50202.Wx42038 L-shaped lever handle knob, 8mm, Class 4 Fixed knob model 820 outside and lever handle aperture with rosette model 203, inside, including square pin and fastening hardware # 50202.Wx42039 L-shaped lever handle knob, 9mm, Class 4, FS Fixed knob model 820 outside and lever handle aperture with rosette Model 203, inside, in fire protection version, including square pin and fastening hardware 37
SAFE-O-TRONIC access DS-T door locking system Fittings Fittings model 202 / 820 Fittings in the form of lever handle fittings U-shaped model 202 and security lever fittings with lever handle aperture with rosette model 202 and fixed knob model 820, surface: matt stainless steel. 38
Lever handle lever handle Lever handle knob # 50202.Dx42028 Lever handle U-shaped lever handle, 8mm, Class 4 Lever handle apertures with rosette model 202 for inside and outside, including square pin and fastening hardware # 50202.Dx42029 Lever handle U-shaped lever handle, 9mm, Class 4, FS lever handle apertures with rosette model 202 for inside and outside, in fire protection version including square pin and fastening hardware # 50202.Wx42028 U-shaped lever handle knob, 8mm, Class 4 Fixed knob model 820 outside and lever handle aperture with rosette model 202, inside, including square pin and fastening hardware # 50202.Wx42029 U-shaped lever handle knob, 9mm, Class 4, FS Fixed knob model 820 outside and lever handle aperture with rosette model 202, inside, in fire protection version, including square pin and fastening hardware 39
SAFE-O-TRONIC access DS-T door locking system Fittings Fittings model 209 / 820 Fittings in the form of lever handle fittings U-shaped model 209 and lever handle fittings with lever handle aperture with rosette model 209 and fixed knob model 820, surface: matt stainless steel. 40
Lever handle lever handle Lever handle knob # 50202.Dx42098 Lever handle U-shaped lever handle, 8mm, Class 4 Lever handle apertures with rosette model 209 for inside and outside, including square pin and fastening hardware # 50202.Dx42099 Lever handle U-shaped lever handle, 9mm, Class 4, FS lever handle apertures with rosette model 209 for inside and outside, in fire protection version including square pin and fastening hardware # 50202.Wx42098 U-shaped lever handle knob, 8mm, Class 4 Fixed knob model 820 outside and lever handle aperture with rosette model 209, inside, including square pin and fastening hardware # 50202.Wx42099 U-shaped lever handle knob, 9mm, Class 4, FS Fixed knob model 820 outside and lever handle aperture with rosette model 209, inside, in fire protection version, including square pin and fastening hardware 41
SAFE-O-TRONIC access DS-T door locking system Fittings Fixed knob model 820 Surface: matt stainless steel # 50299506 42
Fitting accessories Square pin Lever handle lever handle # 50299576H Square pin 7mm A 110 DR for lever handle lever handle, 7mm, measurement A = 110mm # 50299577H Square pin 8mm A 100 DR for lever handle lever handle, 8mm, measurement A = 100mm # 50299578H Square pin 8mm A 110 DR for lever handle lever handle, 8mm, measurement A = 110mm # 50299579H Square pin 9mm A 90 DR for lever handle lever handle, 9mm, measurement A = 90mm # 50299580H Square pin 9mm A 110 DR for lever handle lever handle, 9mm, measurement A = 110mm Lever handle knob # 50299570H Square pin 7mm A 70 DK, can be screwed into fixed knob, 7mm, measurement A = 70mm # 50299571H Square pin 7mm A 110 DK, can be screwed into fixed knob, 7mm, measurement A = 110mm # 50299572H Square pin 8mm A 90 DK, can be screwed into fixed knob, 8mm, measurement A = 90mm # 50299573H Square pin 8mm A 110 DK, can be screwed into fixed knob, 8mm, measurement A = 110mm # 50299574H Square pin 9mm A 90 DK, can be screwed into fixed knob, 9mm, measurement A = 90mm # 50299575H Square pin 9mm A 110 DK, can be screwed into fixed knob, 9mm, measurement A = 110mm 43
SAFE-O-TRONIC access DS-T door locking system Fitting accessories Decorative plates (renovation plates) for renovation Matt stainless steel material, 1.5mm thick # 50299600E Decorative plate set model E, 70-72mm gap, for DS-T # 50299600F Decorative plate set model F, 78mm gap, for DS-T Decorative plate set model E (left: outside - right: inside) Decorative plate set model F (left: outside - right: inside) 44
Decorative plates (renovation plates) for renovation Matt stainless steel material, 1.5mm thick # 50299600G Decorative plate set model G, 88mm gap, for DS-T # 50299600H Decorative plate set model H, 92mm gap, for DS-T Decorative plate set model G (left: outside - right: inside) Decorative plate set model H (left: outside - right: inside) 45
SAFE-O-TRONIC access DS door locking system Overview Features SAFE-O-TRONIC access DS SAFE-O-TRONIC access DS-T 200 300 300 DND 400 200 300 400 Open and close using 4-6 digit user code x x x x Read/write by RFID data carriers at 13.56MHz x x x x x Use of a RFID data carrier as an alternative to PIN code x x Use of a RFID data carrier in conjunction with PIN code x x Contactless, efficient alarm x x x x x Software-assisted programming using system keys x x x x x x x Hardware-assisted programming using a programming kit x x x x x Visual messages and sounds x x x x x x x 65,535 door-locking systems per facility x x x x x x x Time model validity start, validity end and time zones x x x x x x x Operating mode with 20,000 ID numbers x x x x x Operating mode with 2,500 serial numbers (only UID) x x x x x Office mode function for time-limited door activations x x x x x Battery status monitoring / battery status can be checked x x x x x x x Fully programmable; access authorisations can be changed x x x x x x x 99 different time-limited user codes x x x x Individual authorisation of up to 20,000 keys x x x x x Locking plan configuration for up to 4,000 locking groups x x x x x Triple locking group assignment per door locking system x x x x x Master code function to open and close x x x x Configurable master key function x x x x x x x Time lock to prevent unauthorised attempts at opening x x x x Automatic transfer of access authorisation x x x x x Configurable locking log memory x x x x x x x Minimal memory requirements (1 sector) on RFID data carrier x x x x x Simple integration into data systems x x x x x Operation adapted to the needs of the disabled x x x x x x x Simple rosette fitting installation x x x x x x x Customisation options x x x x x x x Do not disturb function x 46
Optional accessories SAFE-O-TRONIC access DS SAFE-O-TRONIC access DS-T 200 300 300 DND 400 200 300 400 Mechanical locking cylinder x x x x U-shaped door handle model 202 (only class 4) x x x x U-shaped door handle model 209 (only class 4) x x x x Blind rosettes x x x x PZ rosettes x x x x Rosette with rotary knob x x x x Decorative base plates for renovation conversion x x x x x x x Integration into the CyberNet network x x x x x Supports NFC applications x x x x x Lever handle set x x x Security lever set x x x Customisation SAFE-O-TRONIC access DS SAFE-O-TRONIC access DS-T 200 300 300 DND 400 200 300 400 Printing on front panel with motif x x x x x x x Decorative lever handle rosette in light beech x x x x Decorative lever handle rosette in black beech x x x x Decorative lever handle rosette in oak x x x x 47
48
Door locking systems SAFE-O-TRONIC access CS 49
SAFE-O-TRONIC access CS door locking system SAFE-O-TRONIC access CS300 DK1 RFID double knob cylinder with single-sided electronic access authorisation Double knob cylinder with RFID closing and programming function, for using PZ prepared mortise locks according to DIN 18252. The double knob cylinder consists of a cylinder adapter, an electronic knob module and a mechanical knob. 42,7 20 n 40 n 29,5 A B 50
Technical specifications, Lengths: 26/26mm, 26/30mm and in 5mm increments starting from 30/30mm, Surface of electronic knob module: solid metal, nickel-plated brass, Antenna cover finish: plastic, Two 3-volt lithium batteries, Battery life: approx. 3 years or approx. 30,000 actuations, Protection class IP 65, Operating temperature range: -15 to +65 C (battery has limited life at <0 C) SAFE-O-TRONIC access CS300 DK1 is available in the following models: # 50203.DK1 The fittings are available as an option. 51
SAFE-O-TRONIC access CS door locking system SAFE-O-TRONIC access CS300 DK2 RFID double knob cylinder with dual-sided separate electronic access authorisation Double knob cylinder with RFID closing and programming function, for using PZ prepared mortise locks according to DIN 18252. The double knob cylinder consists of a cylinder adapter and a two electronic knob modules. 42,7 42,7 n 40 n 40 A B 52
Technical specifications, Lengths: from 30/35mm in 5mm increments, Surface of electronic knob module: solid metal, nickel-plated brass, Antenna cover finish: plastic, Two 3-volt lithium batteries, Battery life: approx. 3 years or approx. 30,000 actuations, Protection class IP 65, Operating temperature range: -15 to +65 C (battery has limited life at <0 C) SAFE-O-TRONIC access CS300 DK2 is available in the following models: # 50203.DK2 The fittings are available as an option. 53
SAFE-O-TRONIC access CS door locking system SAFE-O-TRONIC access CS300 HK1 RFID half cylinder with single-sided electronic access authorisation Half cylinder with RFID closing and programming function, for using PZ prepared mortise locks according to DIN 18252. The half cylinder consists of a cylinder adapter and an electronic knob module. 42,7 n 40 A 10 54
Technical specifications, Lengths: from 30/10mm in 5mm increments, Surface of electronic knob module: solid metal, nickel-plated brass, Antenna cover finish: plastic, Two 3-volt lithium batteries, Battery life: approx. 3 years or approx. 30,000 actuations, Protection class IP 65, Operating temperature range: -15 to +65 C (battery has limited life at <0 C) SAFE-O-TRONIC access CS300 HK1 is available in the following models: # 50203.HK1 The fittings are available as an option. 55
SAFE-O-TRONIC access CS door locking system SAFE-O-TRONIC access CS300 DKP RFID double knob cylinder anti-panic with single-sided electronic access authorisation Anti-panic cylinder for emergency exit locks that require a defined lock pin position of the cylinder, with RFID locking and programming function, for using PZ prepared mortise locks according to DIN 18252. The anti-panic cylinder consists of a cylinder adapter with a fixed mounted mechanical knob and an electronic knob module. 42,7 20 n 40 n 29,5 A B 56
Technical specifications, Lengths: From 30/30mm in 5mm increments, Surface of electronic knob module: solid metal, nickel-plated brass, Antenna cover finish: plastic, Two 3-volt lithium batteries, Battery life: approx. 3 years or approx. 30,000 actuations, Protection class IP 65, Operating temperature range: -15 to +65 C (battery has limited life at <0 C) SAFE-O-TRONIC access CS300 DKP is available in the following models: # 50203.DKP The fittings are available as an option. 57
SAFE-O-TRONIC access CS door locking system Accessories SAFE-O-TRONIC access CS300 Replacement parts # 50203ZG xx xx Cylinder adapter for RFID double knob cylinder 50203.DK1 and 50203.DK2 Standard length: 30/30, available from length: 26/26 Optional: extension in 5mm increments available up to a total length of 70mm per side # 50203AZ xx xx Cylinder adapter for RFID anti-panic double knob cylinder 50203.DKP with additional function for special anti-panic locks, mechanical knob is mounted in a fixed position Standard length: 30/30, available from length: 30/30 Optional: extension in 5mm increments available up to a total length of 70mm per side # 50203HZ xx xx Cylinder adapter for RFID half cylinder 50203.HK1 Standard length: 30/10, available from length: 30/10 Optional: extension in 5mm increments available outside up to a total length of 70mm # 50203EK Electronic knob module # 50203MK Mechanical knob, not available for anti-panic model 58
Battery for RFID cylinder # 50203B 3-volt lithium battery for SAFE-O-TRONIC access CS electronic knob module. 2 batteries are required for each electronic knob module 59
SAFE-O-TRONIC access CS door locking system Fittings Fittings model 203 / 820 Fittings in the form of lever handle fittings L-shaped model 203 and security lever fittings with lever handle aperture with rosette model 203 and fixed knob model 820, surface: matt stainless steel. 60
Lever handle lever handle Lever handle knob # 50202.Dx32038 Lever handle L-shaped lever handle, 8mm, Class 3 lever handle apertures with rosette model 203 for inside and outside, includes square pin and fastening hardware # 50202.Dx42038 Lever handle L-shaped lever handle, 8mm, Class 4 lever handle apertures with rosette model 203 for inside and outside, includes square pin and fastening hardware # 50202.Dx42039 Lever handle L-shaped lever handle, 9mm, Class 4, FS lever handle apertures with rosette model 203 for inside and outside, in fire protection version including square pin and fastening hardware # 50202.Wx32038 L-shaped lever handle knob, 8mm, Class 3 fixed knob model 820 outside and lever handle aperture with rosette model 203, inside, including square pin and fastening hardware # 50202.Wx42038 L-shaped lever handle knob, 8mm, Class 4 fixed knob model 820 outside and lever handle aperture with rosette model 203, inside, including square pin and fastening hardware # 50202.Wx42039 L-shaped lever handle knob, 9mm, Class 4, FS fixed knob model 820 outside and lever handle aperture with rosette model 203, inside, in fire protection version, including square pin and fastening hardware 61
SAFE-O-TRONIC access CS door locking system Fittings Fittings model 202 / 820 Fittings in the form of lever handle fittings U-shaped model 202 and security lever fittings with lever handle aperture with rosette model 202 and fixed knob model 820, surface: matt stainless steel. 62
Lever handle lever handle Lever handle knob # 50202.Dx42028 Lever handle U-shaped lever handle, 8mm, Class 4 lever handle apertures with rosette model 202 for inside and outside, including square pin and fastening hardware # 50202.Dx42029 Lever handle U-shaped lever handle, 9mm, Class 4, FS lever handle apertures with rosette model 202 for inside and outside, in fire protection version including square pin and fastening hardware # 50202.Wx42028 U-shaped lever handle knob, 8mm, Class 4 fixed knob model 820 outside and lever handle aperture with rosette model 202, inside, including square pin and fastening hardware # 50202.Wx42029 U-shaped lever handle knob, 9mm, Class 4, FS fixed knob model 820 outside and lever handle aperture with rosette model 202, inside, in fire protection version, including square pin and fastening hardware 63
SAFE-O-TRONIC access CS door locking system Fittings Fittings model 209 / 820 Fittings in the form of lever handle fittings U-shaped model 209 and security lever fittings with lever handle aperture with rosette model 209 and fixed knob model 820, surface: matt stainless steel. 64
Lever handle lever handle Lever handle knob # 50202.Dx42098 Lever handle U-shaped lever handle, 8mm, Class 4 Lever handle apertures with rosette model 209 for inside and outside, including square pin and fastening hardware # 50202.Dx42099 Lever handle U-shaped lever handle, 9mm, Class 4, FS lever handle apertures with rosette model 209 for inside and outside, in fire protection version including square pin and fastening hardware # 50202.Wx42098 U-shaped lever handle knob, 8mm, Class 4 fixed knob model 820 outside and lever handle aperture with rosette model 209, inside, including square pin and fastening hardware # 50202.Wx42099 U-shaped lever handle knob, 9mm, Class 4, FS fixed knob model 820 outside and lever handle aperture with rosette model 209, inside, in fire protection version, including square pin and fastening hardware 65
SAFE-O-TRONIC access CS door locking system Fittings Fixed knob model 820 Surface: matt stainless steel # 50299506 66
Fitting accessories Square pin Lever handle lever handle # 50299576H Square pin 7mm A 110 DR for lever handle lever handle, 7mm, measurement A = 110mm # 50299577H Square pin 8mm A 100 DR for lever handle lever handle, 8mm, measurement A = 100mm # 50299578H Square pin 8mm A 110 DR for lever handle lever handle, 8mm, measurement A = 110mm # 50299579H Square pin 9mm A 90 DR for lever handle lever handle, 9mm, measurement A = 90mm # 50299580H Square pin 9mm A 110 DR for lever handle lever handle, 9mm, measurement A = 110mm Lever handle knob # 50299570H Square pin 7mm A 70 DK, can be screwed into fixed knob, 7mm, measurement A = 70mm # 50299571H Square pin 7mm A 110 DK, can be screwed into fixed knob, 7mm, measurement A = 110mm # 50299572H Square pin 8mm A 90 DK, can be screwed into fixed knob, 8mm, measurement A = 90mm # 50299573H Square pin 8mm A 110 DK, can be screwed into fixed knob, 8mm, measurement A = 110mm # 50299574H Square pin 9mm A 90 DK, can be screwed into fixed knob, 9mm, measurement A = 90mm # 50299575H Square pin 9mm A 110 DK, can be screwed into fixed knob, 9mm, measurement A = 110mm 67
SAFE-O-TRONIC access CS door locking system Fitting accessories Rosettes to complement SAFE-O-TRONIC access CS Surface: matt stainless steel # 50299508 Rosette set 2 Model: stainless steel, PC punch hole PC punch hole covering, PC punch hole PC punch hole substructure # 50299509 Rosette set 3 Model: stainless steel, blind covering PC punch hole, blind substructure PC punch hole # 50299511 Rosette set 5 Model: stainless steel, blind covering PC punch hole, PC punch hole substructure PC punch hole Rosette set 2 Rosette set 3 Rosette set 5 68
69
SAFE-O-TRONIC access CS door locking system Overview Features SAFE-O-TRONIC access CS 300 DK1 300 DK2 300 HK1 Read/write by RFID data carriers at 13.56MHz x x x x Contactless, efficient alarm x x x x Software-assisted programming using system keys x x x x Hardware-assisted programming using a programming kit x x x x Visual messages and sounds x x x x 65,535 door-locking systems per facility x x x x Time model validity start, validity end and time zones x x x x Operating mode with 20,000 ID numbers x x x x Operating mode with 2,500 serial numbers (only UID) x x x x Battery status monitoring / battery status can be checked x x x x Fully programmable; access authorisations can be changed x x x x Individual authorisation of up to 20,000 keys x x x x Locking plan configuration for up to 4,000 locking groups x x x x Triple locking group assignment per door locking system x x x x Configurable master key function x x x x Automatic transfer of access authorisation x x x x Configurable locking log memory x x x x Minimal memory requirements (1 sector) on RFID data carrier x x x x Simple integration into data systems x x x x Modular design x x x x Battery change/removal with electronic authorisation x x x x Opening using external power supply if battery is dead x x x x Individual assignment of access authorisation for each knob side x Automatic reset of lock pin x Customisation options 300 DKP 70
Optional accessories SAFE-O-TRONIC access CS 300 DK1 300 DK2 300 HK1 Blind rosettes x PZ rosettes x x x x Integration into the CyberNet network x x x x Supports NFC applications x x x x Lever handle set x x x x Security lever set x x x x Battery change tool x x x x Logo disc for electronic knob module x x x x Logo disc removal tool x x x x Low power adapter x x x x 300 DKP 71
72
Furniture locking systems SAFE-O-TRONIC access LS 73
SAFE-O-TRONIC access LS furniture locking system SAFE-O-TRONIC access LS100 PIN code furniture locking system Furniture locking system with PIN code function, with black or white front panel, capacitive keypad and round rotary knob. With SAFE-O-TRONIC access LS100, four installation directions can be selected and it is for universal use for all cupboard door materials as well as right and left doors. Award winning locking system: red dot award: product design 2010 and nominated for "Designpreis Deutschland 2011" 74
Technical specifications, Dimensions including rotary knob (HxWxD): 151mm x 38mm x 33mm, Weight: approx. 300 g, Standard alkaline batteries on the outside of the door, Battery life: approx. 3 years or approx. 30,000 actuations, Protection class IP 43, Door thickness up to 18mm, other door thicknesses optional, Operating temperature range: 0 to +60 C, Storage temperature range: -15 to +70 C, Relative humidity: 10 90% non-condensing SAFE-O-TRONIC access LS100 is available in the following models: # 300841 Model with standard locking lever, 40mm, straight design (additional locking lever on request) Installation directions Installation direction A (rotary knob on top) Installation direction B (rotary knob on bottom) Installation direction C (rotary knob on the left) Installation direction D (rotary knob on the right) 75
SAFE-O-TRONIC access LS furniture locking system SAFE-O-TRONIC access LS200 PIN code furniture locking system with master key function Furniture locking system with RFID programming and RFID master key function, with black or white front panel, capacitive keypad and round rotary knob. With SAFE-O-TRONIC access LS200, four installation directions can be selected and it is for universal use for all cupboard door materials as well as right and left doors. Award winning locking system: red dot award: product design 2010 and nominated for "Designpreis Deutschland 2011" 76
Technical specifications, Dimensions including rotary knob (HxWxD): 151mm x 38mm x 33mm, weight: approx. 300g, standard alkaline batteries on the outside of the door, battery life: approx. 3 years or approx. 30,000 actuations, protection class IP 43, door thickness up to 18mm, other door thicknesses optional, operating temperature range: 0 to +60 C, storage temperature range: -15 to +70 C, relative humidity: 10 90% non-condensing SAFE-O-TRONIC access LS200 is available in the following models: # 300842 Model with standard locking lever, 40mm, straight design (additional locking lever on request) Installation directions Installation direction A (rotary knob on top) Installation direction B (rotary knob on bottom) Installation direction C (rotary knob on the left) Installation direction D (rotary knob on the right) 77
SAFE-O-TRONIC access LS furniture locking system SAFE-O-TRONIC access LS300 RFID furniture locking system Furniture locking system with RFID function, with black or white front panel, capacitive keypad and round rotary knob. With SAFE-O-TRONIC access LS300, four installation directions can be selected and it is for universal use for all cupboard door materials as well as right and left doors. Award winning locking system: red dot award: product design 2010 and nominated for "Designpreis Deutschland 2011" 78
Technical specifications, dimensions including rotary knob (HxWxD): 151mm x 38mm x 33mm, weight: approx. 300g, standard alkaline batteries on the outside of the door, battery life: approx. 3 years or approx. 30,000 actuations, protection class IP 43, door thickness up to 18mm, other door thicknesses optional, operating temperature range: 0 to +60 C, storage temperature range: -15 to +70 C, relative humidity: 10 90% non-condensing SAFE-O-TRONIC access LS300 is available in the following models: # 300843 Model with standard locking lever, 40mm, straight design (additional locking lever on request) Installation directions Installation direction A (rotary knob on top) Installation direction B (rotary knob on bottom) Installation direction C (rotary knob on the left) Installation direction D (rotary knob on the right) 79
SAFE-O-TRONIC access LS furniture locking system SAFE-O-TRONIC access LS400 RFID / PIN code furniture locking system Furniture locking system with combined RFID and PIN code function, with black or white front panel, capacitive keypad and round rotary knob. With SAFE-O-TRONIC access LS400, four installation directions can be selected and it is for universal use for all cupboard door materials as well as right and left doors. Award winning locking system: red dot award: product design 2010 and nominated for "Designpreis Deutschland 2011" 80
Technical specifications, dimensions including rotary knob (HxWxD): 151mm x 38mm x 33mm, weight: approx. 300g, standard alkaline batteries on the outside of the door, battery life: approx. 3 years or approx. 30,000 actuations, protection class IP 43, door thickness up to 18mm, other door thicknesses optional, operating temperature range: 0 to +60 C, storage temperature range: -15 to +70 C, relative humidity: 10 90% non-condensing SAFE-O-TRONIC access LS400 is available in the following models: # 300844 Model with standard locking lever, 40mm, straight design (additional locking lever on request) Installation directions Installation direction A (rotary knob on top) Installation direction B (rotary knob on bottom) Installation direction C (rotary knob on the left) Installation direction D (rotary knob on the right) 81
SAFE-O-TRONIC access LS furniture locking system Customisation Laser engraving for labelling SAFE-O-TRONIC access LS100, 200, 300 and 400 plates # 5009433 Laser engraving with locker numbering # 5009432 Laser engraving with motif (such as logo, graphic or lettering) - standard for all furniture locking systems in the system Templates: File formats BMP, TIFF, JPEG or PCX, at least 300 DPI, black and white # 5009435 Laser engraving with lettering (such as different user names) - individual for each furniture locking system in the system Templates: File formats BMP, TIFF, JPEG or PCX, at least 300 DPI, black and white 82
Accessories Rectangular rotary knob # 50299102-300 Rectangular rotary knob (instead of round rotary knob) with convenient vacant/occupied indicator Battery pack # 38400200 Battery pack, consisting of 3 standard alkaline batteries, for SAFE-O-TRONIC access DS, DS-T and LS. Battery life: approx. 3 years or approx. 30,000 actuations. 83
SAFE-O-TRONIC access LS furniture locking system Overview Features SAFE-O-TRONIC access LS Open and close using 4-6 digit user code 100 200 300 400 x (4 digit) Read/write by RFID data carriers at 13.56MHz x x Use of a RFID data carrier as an alternative to PIN code x Use of RFID data carrier in conjunction with PIN code x Contactless, efficient alarm x x Software-assisted programming using system keys x x x Hardware-assisted programming using a programming kit x x Visual messages and sounds x x x x Capacitive, hard-wearing keypad x x x 65,535 furniture locking systems per facility x x x Time model validity start, validity end and time zones x x x Open locker selection operating mode x x x x "All open" fixed locker assignment operating mode x x x "One open" fixed locker assignment operating mode x x x Operating mode with 20,000 ID numbers x x Operating mode with 2,500 serial numbers (only UID) x x Battery status monitoring / battery status can be checked x x x x Fully programmable; access authorisations can be changed x x x 99 different time-limited user codes x x Automatic assignment of user codes x x Automatic block when exceeding usage time x x x Automatic opening when exceeding usage time x x x Individual authorisation of up to 20,000 keys x x Locking plan configuration for up to 4,000 locking groups x x Triple locking group assignment per furniture locking system x x Master code function to open and close x x x Configurable master key function x x x Time lock to prevent unauthorised attempts at opening x x x Automatic transfer of access authorisation x x Configurable locking log memory x x x Minimal memory requirements (1 sector) on RFID data carrier x x Simple integration into data systems x x Manual unlocking option for jammed doors x x x x Proven burglar-proof capacity x x x x Operation adapted to the needs of the disabled (square rotary knob) x x x x Customisation options x x x x x x 84
Optional accessories SAFE-O-TRONIC access LS 100 200 300 400 Square rotary knob x x x x Integration into the CyberNet network x x Supports NFC applications x x Battery replacement aid x x x x Base plates for renovation conversion x x x x Panel to convert to SAFE-O-TRONIC access LS x x x x Special lever x x x x Customisation SAFE-O-TRONIC access LS 100 200 300 400 Laser engraving with locker numbering x x x x Laser engraving with motif x x x x Laser engraving with lettering x x x x 85
86
Terminal systems SAFE-O-TRONIC access TS 87
SAFE-O-TRONIC access TS terminals SAFE-O-TRONIC access TS300 RFID terminal (offline) RFID terminal (offline) to control an I/O extension board, for use in low voltage range (24-48V). Can be used as a wall-mounted reader in flush and surface-mounted versions or as a built-in reader. The power supply must be provided by the customer. The range of functions of the RFID terminal (offline) is the same as the range of functions of the SAFE-O-TRONIC access DS300. 84.2mm 40.0mm 22.0mm 84.2mm 77.7mm 51.5mm 14.0mm 88
Technical specifications, lower housing part dimensions: 84mm x 84mm x 22mm, colour of lower housing part: Body: white / front panel: black, surface-mounted adapter dimensions: 77.7mm x 77.7mm x 18.0mm, surface-mounted adapter colour: light grey, weight: approx. 150g, protection class IP 54, power supply: ext. power supply 24V to 48 V DC ± 10%, power consumption: typically 3.2W - max. 3.8W, operating temperature range: -20 C to +55 C, storage temperature range: -40 C to +85 C, relative humidity: 95% (non-condensing), antenna: internal, approx. 40mm x 40mm, operating frequency: 13.56MHz, transmitting power: 250mW 2dB, RF interface: ISO14443-A, NFC, supported transponder types: e.g. mifare classic (mini, 1k, 4k), mifare DESfire, Smart MX, mifare Plus, LED: blue, green, red (function can be configured), summer: integrated, real-time clock: 24 hour power reserve, accuracy ± 2s/day # 38490070 89
SAFE-O-TRONIC access TS terminals SAFE-O-TRONIC access TS300 CyberSpot RFID terminal (online) CyberSpot RFID terminal (online) to write to RFID data carriers with access authorisations, validities and time zones. With power supply in low voltage range (24-48V) or via "Power over Ethernet". Can be used as a wall-mounted reader in flush and surface-mounted versions or as a built-in reader. Can also be used to control an I/O extension board. The power supply must be provided by the customer. 84.2mm 40.0mm 22.0mm 84.2mm 77.7mm 51.5mm 14.0mm 90
Technical specifications, Lower housing part dimensions: 84mm x 84mm x 22mm, Colour of lower housing part: Body: white / front panel: black, surface-mounted adapter dimensions: 77.7mm x 77.7mm x 18.0mm, surface-mounted adapter colour: light grey, weight: approx. 150g, protection class IP 54, power supply: power over Ethernet, IEEE802.3af alternative: ext. power supply 24V to 48 V DC 10%, power consumption: typically 3.2W - max. 3.8W (IEEE802.3af powered devices class: 1), operating temperature range: -20 C to +55 C, storage temperature range: -40 C to +85 C, relative humidity: 95% (non-condensing), cable specification: max. 100m CAT-5 cable, antenna: internal, approx. 40mm x 40mm, operating frequency: 13.56MHz, transmitting power: 250mW 2dB, RF interface: ISO14443-A, NFC, supported transponder types: e.g. mifare classic (mini, 1k, 4k), mifare DESfire, Smart MX, mifare Plus, LED: blue, green, red (function can be configured), summer: integrated, real-time clock: 24 hour power reserve, accuracy ± 2s/day, TCP/IP connection: LSA terminal, Interface: Ethernet 10BASE-T/100BASE-TX automatic MDI/MDI-X cross over correction TCP/IP protocol, IPv4, Ethernet factory settings: IP address: 192.168.10.10 Subnet mask: 255.255.255.0 Port: 10001 DHCP: off, EEPROM: for configuration parameters (1 million write cycles), FRAM: for lock data (10 14 write cycles) # 38490040 91
SAFE-O-TRONIC access TS terminals SAFE-O-TRONIC access TS300 I/O extension board as a supplement to the RFID terminal (offline) and to the CyberSpot RFID terminal (online) I/O extension board e.g. to control electric door openers, car park barriers or turnstiles for installation in a flush-mounted box. With relay, 1x change-over contact (contact rating 24V AC/DC, 1.5A). Technical specifications, dimensions: 43mm x 39mm x 13mm, weight: approx. 20g, protection class IP 20, power supply: + 5 V DC, operating temperature range: -20 C to +70 C, storage temperature range: -40 C to +85 C, relative humidity: 95% (non-condensing), cable specification: max. 5m (twisted pair cable), Relay: 1x change-over contact (contact rating: 24V AC/DC 1.5A), digital inputs: 2x to switch against GND (max. 1 kω) # 38490071 92
16/O extension board 16/O extension board for individual selection of up to 16 outputs (such as for activating floors of a lift), for use with RFID terminal (offline), supply voltage: 7-24V. The power supply must be provided by the customer # 38490075 93
SAFE-O-TRONIC access TS terminals SAFE-O-TRONIC access TS300 USB Mifare desktop reader Desktop reader to program system keys and RFID data carriers to connect to the PC. The power supply is provided and data exchanged via a USB interface. Technical specifications, dimensions (WxHxD): 144mm x 84mm x 18mm, weight: approx. 105g, housing: ASA plastic, front: acrylic glass, colour: black and white, protection class IP 42, operating frequency: 13.56MHz, RF transmitting power: 100mW, Power supply: 5V, USB bus powered, Power consumption: max. 140mA, Antenna: integrated, interface: full speed USB (12 MBit/s), signal generator: 2 LEDs, temperature range: operating 20 C to 60 C storage 40 C to 85 C, relative humidity: 95% (non-condensing), MTBF: 500,000 hours # 38490010 94
Communicator Communicator to program SAFE-O-TRONIC access LS300, LS400, DS300, DS-T300, DS400, DS-T400, CS300 locking systems and TS300 terminal systems. Technical specifications, Storage option for data records for up to 60 SAFE-O-TRONIC access locking systems, battery operation, Programming of SAFE-O-TRONIC access locking systems without connected PC, Reading of log data from the SAFE-O-TRONIC access locking systems, USB interface for data exchange with PC and to charge the battery, real-time clock: integrated, surface: plastic, colour: black # 38490020 95
SAFE-O-TRONIC access TS terminals SAFE-O-TRONIC access TS300 Info terminal offline Wall-mounted device to display the locker number for "open locker selection" for the SAFE-O-TRONIC access LS300 and LS400. The power supply must be provided by the customer. Technical specifications, dimensions: 199mm x 179mm x 72mm, weight: approx. 500g, protection class IP 54, power supply: 24V to 48 V DC ± 10%, power consumption: typically 4.6W - max. 5.2W, operating temperature range: -10 C to +55 C, storage temperature range: -20 C to +70 C, relative humidity: 95% (non-condensing), antenna: internal, operating frequency: 13.56MHz, transmitting power: 250 mw ± 2 db, RF interface: ISO14443-A, NFC, supported transponder types: e.g. mifare classic (mini, 1k, 4k), mifare DESfire, Smart MX, mifare Plus, LED: 2 x 20 character LCDs backlit, summer: integrated, real-time clock: 24 hour power reserve, accuracy ± 2s/day # 38490030 96
CyberSpot online info terminal Wall-mounted device to display the locker number for "open locker selection" including CyberSpot function for the SAFE-O-TRONIC access LS300 and LS400. The power supply must be provided by the customer. Technical specifications, dimensions: 199mm x 179mm x 72mm, weight: approx. 500g, protection class IP 54, power supply: 24V to 48V DC ± 10%, power consumption: typically 4.6W - max. 5.2W, operating temperature range: -10 C to +55 C, storage temperature range: -20 C to +70 C, relative humidity: 95% (non-condensing), cable specification: max. 100m CAT-5 cable, antenna: internal, approx. 40mm x 40mm, operating frequency: 13.56MHz, transmitting power: 250mW ± 2dB, RF interface: ISO14443-A, NFC, supported transponder types: e.g. mifare classic (mini, 1k, 4k), mifare DESfire, Smart MX, mifare Plus, LED: 2 x 20 character LCDs backlit, summer: integrated, real-time clock: 24 hour power reserve, accuracy ± 2s/day, TCP/IP connection: RJ45 8P8C (internal), interface: Ethernet 10BASE-T/100BASE-TX automatic MDI/MDI-X cross over correction TCP/IP protocol, IPv4, Ethernet factory settings: IP address: 192.168.10.10 Subnet mask: 255.255.255.0 Port: 10001 DHCP: off, EEPROM: for configuration parameters (1 million write cycles), FRAM: for lock data (10 14 write cycles) # 38490031 97
SAFE-O-TRONIC access TS terminals SAFE-O-TRONIC access TS300 Card switch # 5009533 future linear-abdeckrahmen Cardschalter-Einsatz E-Katalog 2013 E-Katalog 2013 Card switch including frame and centre plate for use as an energy-saving switch, for example. Suitable for RFID cards in ISO format colour: ivory white future linear Unterputz-Einsätze Rahmen Schalter/Taster future linear-abdeckrahmen Cardschalter-Einsatz 1-fach Rahmen 1-polig, Schließer (Arbeitsstrom) Mit Sichtfenster und Beleuchtbar. Beschriftungsträger. Mit kleinen Eckradien Mit für N-Klemme. geschnittene Kanalabdeckungen. Siehe Beschriftungsbogen Nennspannung: 1799 22., 250 V~,, Nennstrom: 10 A Preisgruppe: 01 Nur in Verbindung mit handelsüblichen UP-Gerätedosen nach DIN 49073, Teil 1, montieren oder Busch-Jaeger Preis: 5,62 EUR zzgl. Art.-Nr. Mwst. 3040 UP-Dose Mauerwerk, 3050 UP-Dose Hohlwand oder 3060 UP-Dose Beton), Beleuchtbar durch Einsetzen der Lampe 8350, 8352, 8353, 8337-1, 8345-1 und 8344-1und LED-Einsätze., Bestellnummer: 1754-0-4364 Artikelnummer: 1721-184 Preisgruppe: NSK 01 EA-Nummer: 4011395124307 Preis: 9,63 EUR zzgl. Mwst. Bestellnummer: 1012-0-1713 Artikelnummer: 2025 U EA-Nummer: 4011395656808 98
SAFE-O-TRONIC access Additional components 99
SAFE-O-TRONIC access additional components Additional components Programming accessories System keys for SAFE-O-TRONIC LS200, 300, 400 and DS200, 300, 400, DS-T200, 300, 400 and CS300 and TS300 # 38490060 system key set to program and manage a SAFE-O-TRONIC access locking system in combination with the lock manager software, consisting of 7 RFID data carriers in ISO format preconfigured at the factory. Each system key is labelled with an object-specific object number and a standard KGEN (locking sequence). # 38490060TK test key Key for the functional testing of non-programmed SAFE-O-TRONIC access RFID locking systems. After programming, the test key has no locking functions in the locking system. 100
Programming sets for SAFE-O-TRONIC access LS200 and 300 LS 200 Free code INIT LS 200 Fix code INIT_ALL LS 200 Fix code PROG LS 200 Battery key LS 200 Master key I # 38490060SK200 Programming set LS200 for programming and operating a SAFE-O-TRONIC access LS200 locking system without software or PC for the "fixed locker assignment" and "open locker selection" operating modes, consisting of 8 RFID data carriers as key fobs preconfigured at the factory. Timerelated functions cannot be programmed with the LS200 programming set. Each LS200 programming set is labelled with an object-specific object number and a standard KGEN (locking sequence). LS 200 Reset key LS 200 INIT_ONE fix code LS 200 Master key II LS 300 Free code INIT LS 300 Fix code INIT_ALL LS 300 Fix code PROG LS 300 Battery key LS 300 Master key I # 38490060SK300 Programming set LS300 for programming and operating a SAFE-O-TRONIC access LS300 locking system without software or PC for the "fixed locker assignment" and "open locker selection" operating modes, consisting of 8 RFID data carriers as key fobs preconfigured at the factory. Timerelated functions cannot be programmed with the LS300 programming set. Each LS300 programming set is labelled with an object-specific object number and a standard KGEN (locking sequence). LS 300 Reset key LS 300 INIT_ONE fix code LS 3 00 Master key II 101
SAFE-O-TRONIC access additional components Additional components Programming accessories Programming sets for SAFE-O-TRONIC access DS200 and 300 DS 200 Fix code INIT_ALL DS 200 Fix code PROG DS 200 Battery key DS 200 Master key II # 38490060DS200 Programming set DS200 to program and operate a SAFE-O-TRONIC access DS200 or DS-T200 locking system without software or PC, consisting of 5 RFID data carriers as key fobs preconfigured at the factory. Time-related functions cannot be programmed with the DS200 programming set. Each DS200 programming set is labelled with a object-specific object number and a standard KGEN (locking sequence). DS 200 Reset key DS 300 Fix code INIT_ALL DS 300 Fix code PROG DS 300 Battery key DS 300 Master key II # 38490060DS300 Programming set DS300 to program and operate a SAFE-O-TRONIC access DS300 or DS-T300 locking system without software or PC, consisting of 5 RFID data carriers as key fobs preconfigured at the factory. Time-related functions cannot be programmed with the DS300 programming set. Each DS300 programming set is labelled with a object-specific object number and a standard KGEN (locking sequence). DS 300 Reset key 102
Programming sets for SAFE-O-TRONIC access CS300 CS 300 Fix code INIT_ALL CS 300 Fix code PROG CS 300 Reset key CS 300 Battery key CS 300 Master key II # 38490060CS300 Programming set CS300 to program and operate a SAFE-O-TRONIC access CS300 locking system without software or PC, consisting of 7 RFID data carriers as key fobs preconfigured at the factory. Time-related functions cannot be programmed with the CS300 programming set. Each CS300 programming set is labelled with an object-specific object number and a standard KGEN (locking sequence). CS 300 Service battery CS 300 Service disasssembly 103
SAFE-O-TRONIC access additional components Additional components Software Lock manager software for SAFE-O-TRONIC access System requirements:, operating system: Windows XP, Vista, Windows 7, Windows 8, processor: Intel / AMD-compatible with 1,500MHz or higher, RAM: 512MB or higher, sound: Optional: Windows-compatible sound card, hard disk: > 200MB free memory space, graphics: VGA graphics card with 1024*768 pixels and 256 colours, pointer device: trackball, integrated mouse pad or PS/2 mouse, interface: one free USB interface USB 1.0 or 2.0, Ethernet interface, drives: CD (RW) drive for installation and if necessary for data backup # 5009023-200 Lock Manager 6, LS200 version to program and manage SAFE-O-TRONIC access LS200 locking systems using a system key set, for installation on commercial notebooks, laptops and PCs with Windows XP, Vista, Windows 7 and Windows 8 operating systems, including user licence and update authorisation., locking plan preparation, locking system management, reading and documentation of locking logs, Preparing, coding and reading RFID data carriers with connected USB reader, reading the data saved in the RFID data carriers 104
# 5009023-6K Lock Manager 6, Key version to program and manage SAFE-O-TRONIC access LS200, LS300, LS400, DS200, DS-T200, DS300, DS-T300, DS400, DS-T400, CS300 and TS300 using a system key set, for installation on commercial notebooks, laptops and PCs with Windows XP, Vista, Windows 7 and Windows 8 operating systems, including user licence and update authorisation., locking plan preparation, locking system management, reading and documentation of locking logs, preparing, coding and reading RFID data carriers with connected USB reader, reading the data saved in the RFID data carriers # 5009023-6C Lock Manager 6, Communicator version to program and manage SAFE-O-TRONIC access LS200, LS300, LS400, DS200, DS-T200, DS300, DS-T300, DS400, DS-T400, CS300 and TS300 using the communicator, for installation on commercial notebooks, laptops and PCs with Windows XP, Vista, Windows 7 and Windows 8 operating systems, including user licence and update authorisation., locking plan preparation, locking system management, reading and documentation of locking logs, preparing, coding and reading RFID data carriers with connected USB reader, reading the data saved in the RFID data carriers 105
SAFE-O-TRONIC access additional components Additional components Software Lock Manager Software Software for SAFE-O-TRONIC CyberNet and ACW System requirements:, operating system: Windows XP, Vista, Windows 7, Windows 8, processor: Intel / AMD-compatible with 1,500MHz or higher, RAM: 512MB or higher, sound: optional: Windows-compatible sound card, hard disk: > 200MB free memory space, graphics: VGA graphics card with 1024*768 pixels and 256 colours, pointer device: trackball, integrated mouse pad or PS/2 mouse, Interface: one free USB interface USB 1.0 or 2.0, Ethernet interface, drives: CD (RW) drive for installation and if necessary for data backup, installed software packages:.net Framework 4.0 and Visual C++ 2005 Redistributable package (x 86) # 5009023-6CCN Lock Manager 6, CyberNet version to program and manage SAFE-O-TRONIC access LS200, LS300, LS400, DS200, DS-T200, DS300, DS-T300, DS400, DS-T400, CS300 and TS300 using system key set and communicator, including CyberNet network, for installation on commercial notebooks, laptops and PCs with Windows XP, Vista, Windows 7 and Windows 8 operating systems, including user licence and update authorisation., locking plan preparation, locking system management, reading and documentation of locking logs, preparing, coding and reading RFID data carriers with connected USB reader, reading the data saved on the RFID data carriers, Online programming of access authorisations and time validity of the RFID data carriers via the CyberSpot RFID terminal (online), online evaluation of the battery status of the RFID data carriers via the CyberSpot RFID terminal (online) # 5009023-6ACW Lock Manager 6 ACW control software for connection of SAFE-O-TRONIC access to all current front-office systems such as Micros Fidelio, Hogatex, Protel, Gubse 106
Software Development Kits for SAFE-O-TRONIC access LS300 and 400, DS300, DS-T300, DS400 and DS-T400 as well as CS 300 and TS 300 # 38499902 Single use licence for software development kit 2 to integrate SAFE-O-TRONIC access door and furniture locking systems into data systems with an SAG reader infrastructure. Intended for use with Visual C++ programming language (class library) development environment: Visual Studio 2005, 2008 and 2010, not including: Visual Studio Express editions # 38499903 Single use licence for software development kit 3 to integrate SAFE-O-TRONIC access door and furniture locking systems into data systems with an SAG reader infrastructure. Intended for use with Visual C/VisualBasic.NET programming language (class library) development environment: Visual Studio 2005, 2008 and 2010, not including: Visual Studio Express editions # 38499904 Single use licence for software development kit 4 to integrate SAFE-O-TRONIC access door and furniture locking systems into data systems with an external RFID reader infrastructure. Intended for use with Visual C++ programming language (function library) development environment: Visual Studio 2005, not including: Visual Studio Express editions 107
SAFE-O-TRONIC access additional components Additional components RFID data carrier components RFID cards in ISO format # 5 009121M1 MIFARE 1K (Standard) RFID data carriers in card form, unprinted, uncoded, blank for individual design (20 pack) # 5 009151M1 as before (50 pack) # 5 009121M4 MIFARE 4K RFID data carriers in card form, unprinted, uncoded, blank for individual design (20 pack) # 5 009151M4 as before (50 pack) # 5 009121M8D MIFARE DESFire 8K EV1 RFID data carriers in card form, unprinted, uncoded, blank for individual design (20 pack) # 5 009151M8D as before (50 pack) RFID key fob # 5 009352M1.BLA MIFARE 1K (Standard) RFID data carrier as a key fob, uncoded, Design: sail shape, colour: blue (20 pack) # 5 009353M1.BLA as before (50 pack) # 5 009352M4.BLA MIFARE 4K RFID data carrier as a key fob, uncoded, Design: sail shape, colour: blue (20 pack) # 5 009353M4.BLA as before (50 pack) 108
# 5 009358M1 MIFARE 1K (Standard) RFID data carrier as a key fob, waterproof, uncoded, printable Design: round, colour: black (outside) / white (inside) (20 pack) # 5 009359M1 as before (50 pack) # 5 009358M4 MIFARE 4K RFID data carrier as a key fob, waterproof, uncoded, printable Design: round, colour: black (outside) / white (inside) (20 pack) # 5 009359M4 as before (50 pack) RFID bracelet sets # 5 009360M1 MIFARE 1K (Standard) RFID data carrier in the shape of a watch, black nylon bracelet, waterproof, uncoded, printable Colours: black (outside) / white (inside) (20 pack) # 5 009361M1 as before (50 pack) # 5 009360M4 MIFARE 4K RFID data carrier in the shape of a watch, black nylon bracelet, waterproof, uncoded, printable Colours: black (outside) / white (inside) (20 pack) # 5 009361M4 as before (50 pack) 109
SAFE-O-TRONIC access additional components Customisation RFID data carrier Laser engraving of RFID cards and key fobs # 5009432 Laser engraving on one side with motif (such as graphic, lettering or logo) (per pc.) Templates: file formats BMP, TIFF, JPEG or PCX, at least 300 DPI, black and white 9375 9374 065 066 # 5009433 Laser engraving on one side with consecutive numbering 137 138 19 20 110
111
Schulte-Schlagbaum AG P.O. Box 101240 D - 42512 Velbert Telephone +49 (0) 2051 / 2086-400 cse@sag-schlagbaum.com www.sag-schlagbaum.com 3-703-2 37U1.0 Subject to technical changes.