Standard Cables (Without electromagnetic brake, with electromagnetic brake) CC010ES-2. 1 m CC020ES-2. 2 m CC030ES-2. 3 m CC050ES-2.

Transcription

1 Motorized Actuators Motor Cables EZS /EZS for Clean Room Use This cable is a dedicated cable for connecting the linear slide of the EZS Series and EZS Series for Clean Room Use with the controller. Use the flexible extension cable in applications where the cable is bent and flexed repeatedly. (Cable is for both the electromagnetic brake type and without electromagnetic brake type.) Standard Cables (Without electromagnetic brake, with electromagnetic brake) CC010ES-2 CC020ES-2 CC030ES-2 3 m CC050ES-2 CC070ES-2 7 m CC100ES-2 10 m CC150ES-2 1 CC200ES-2 20 m Keep the cable length at 10 m or less for 24 VDC linear slides. Flexible Extension Cables (Without electromagnetic brake, with electromagnetic brake) CC010ESR-2 CC020ESR-2 CC030ESR-2 3 m CC050ESR-2 CC070ESR-2 7 m CC100ESR-2 10 m CC150ESR-2 1 CC200ESR-2 20 m Keep the cable length at 10 m or less for 24 VDC linear slides. CC ES-2/CC ESR Motor Side 8.28 ϕ9 Controller Side L Sensor Sets Sensor sets dedicated to the EZS Series and, EZS Series for Clean Room Use. The sensor set consists of three sets of a sensor, a sensor mounting bracket and a flexible sensor cable with connector () and 1 shielding plate. The screws needed for installation are also included. PAES-S PAES-SY Sensor Mounting Bracket 3 Pieces Shielding Plate 1 Piece Sensor Output NPN PNP Specifications NPN Type : EE-SX674A (OMRON) Power Supply 5 24 VDC±10%, Ripple (P-P) 10% max. Current Consumption 3A max. Control Output NPN Open-Collector Output, 5 24 VDC, 100 ma max. Residual Voltage 0.8 V max. (At load current of 100 ma) Logic Normally Open/Normally Closed (Selectable, depending on connection) Indicator LED Detection Display (Red) Sensor 3 Pieces Flexible Sensor Cable with Connector () 3 Pieces Conductor: AWG24 (0.m 2 ) PNP Type Power Supply Current Consumption Control Output Logic Indicator LED : EE-SX674R (OMRON) 5 24 VDC±10%, Ripple (P-P) 10% max. 30 ma max. PNP Open-Collector Output, 5 24 VDC, 50 ma max. Residual Voltage 1.3 V max. (At load current of 50 ma) Normally Open/Normally Closed (Selectable, depending on connection) Detection Display (Red) for Sensor Position LS Sensor Detection Position (When the LS sensor is used) Mechanical Stopper Position L2 21 L3 HOME Sensor Detection Position (When the HOME sensor is used) +LS Sensor Detection Position (When the +LS sensor is used) Stroke 21 Mechanical Stopper Position (When the HOME L5 L6 L7 sensor is used) L9 L10 L11 LS Sensor L1 21 L4 HOME Sensor +LS Sensor L8 Linear Slide Size L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 Note EZS EZS EZS If the stroke is 60 mm or below, all three sensors cannot be installed. E-98 ORIENTAL MOTOR GENERAL CATALOGUE

2 33.3 Connector Terminal Block Conversion Units Customer Support Centre Singapore: , Malaysia: , Others: These are conversion units that connect a linear motion controller to a sensor or programmable controller using a terminal block. Includes a signal name plate for easy, one-glance identification of signal names DIN-rail mountable Cable Length: Applicable Type Length CC20T1 For Sensor I/O Connector CC36T1 For I/O Connector CC20T1 B Terminal Block Pin No ϕ4.5 Mounting Hole 2 ϕ8 Counterbore 3.5 Deep DIN Rail Sensor Extension Cables These cables are for connecting the linear motion controller and sensor. CC20D1-1 CC20D CC36T1 B CC20T Terminal Block Pin No CC36T1 2 ϕ4.5 Mounting Hole 2 ϕ8 Counterbore 3.5 Deep DIN Rail Applicable Crimp Terminal Terminal Screw Size: M3 Tightening Torque: 1.2 N m Minimum Applicable Lead Wire: AWG22 (0.3 mm 2 ) Note Round terminals cannot be used. Conductor: AWG28 (0.08 mm 2 ) L 60± ϕ6.4 6.m max. Braided-Shielded 3.m min Pitch Laminate mm min. 4.m max. Motorized Actuators Introduction Types ELS EZS EZS Clean Room DRS DRL Motorized Linear Slides Motorized Cylinders Compact Linear Actuators ELC EZA DG Hollow Rotary Actuators Controller Side Sensor Side E-99

3 Motorized Actuators I/O Cables These cables are dedicated cables for connecting the linear motion controller and programmable controller. The cables are equipped with, at one end of the cable, a half-pitch connector for easy connection to the linear motion controller. CC36D1-1 CC36D2-1 Conductor: AWG28 (0.08 mm 2 ) 60±15 Braided-Shielded Pitch L Laminate Linear Motion Controller Side ϕ7.5 Programmable Controller Side Teaching Pendant The teaching pendant allows you to set and operate various data on hand, as well as to monitor the setting data, current position and I/O status in real time. EZT1 Specifications Display LCD with 2-Colored Backlight Cable Length Mass 0.37 kg Operating Ambient Temperature C (non-freezing) D (25) ϕ24.9 (1.5) Teaching Pendant ( EZT1)/ Data Editing Software (EZED2) Function Comparison Table Functions Teaching Pendant (: EZT1) Data Editing Software (: EZED2) Cable Length 1 Display LCD 17 characters 4 lines PC screen Emergency Stop Button Operation Data Setting Parameter Setting Teaching (Direct/Remote) Operating Data Monitoring I/O and Alarm History Monitoring Waveform Monitoring Test Operation Data Copy Printing Function 2 1 PC interface cable (included) is used 2 The printing function is not available on computers running Windows 98 and Me Teaching Pendant Cable ϕ ϕ11.2 E-100 ORIENTAL MOTOR GENERAL CATALOGUE

4 Data Editing Software Specifications (Operating environment) Customer Support Centre Singapore: , Malaysia: , Others: Various data can be set and edited on a personal computer. The software comes with a PC interface cable used to connect the linear motion controller with a computer. The software also provides various monitoring functions. EZED2 Ver 1.34 or later PC Interface Cable Cable Length PC Connector Type Communication Port Operating Softwares D sub 9-Pin One RS-232C Communication Port : EZED2 Microsoft Windows 2000 Professional Service Pack 4 or Later (Hereinafter, referred to as Windows 2000) Microsoft Windows XP Home Edition Service Pack 2 or Later (Hereinafter, referred to as Windows XP) Microsoft Windows XP Professional Edition Service Pack 2 or Later (Hereinafter, referred to as Windows XP) Microsoft Windows XP Media Center Edition 2004 Service Pack 2 or Later (Hereinafter, referred to as Windows XP) Microsoft Windows XP Media Center Edition 2005 Service Pack 2 or Later (Hereinafter, referred to as Windows XP) Microsoft Windows 98 Service Pack 1 or Later (Hereinafter, referred to as Windows 98) Microsoft Windows 98 Second Edition (Hereinafter, referred to as Windows 98) Microsoft Windows Millennium Edition (Hereinafter, referred to as Windows Me) Windows 2000: 128 MB min. (192 MB min. is recommended), Windows XP Home Edition or Professional Edition: 256 MB min. Memory Windows XP Media Center Edition 2004 or 2005: 320 MB min., Windows 98: 64 MB min. (128 MB min. is recommended) Windows 98 Second Edition: 64 MB min. (128 MB min. is recommended), Windows Me: 96 MB min. (160 MB min. is recommended) Computer Pentium 500 MHz or min. (OS must be supported) for Single Core and Processor Display Resolution Video Adapter and Monitor with Resolution of XGA ( ) min. Hard Disk Capacity Free Disk Space of 60 MB min. Serial Port RS-232C Port, 1 Channel Disk Device CD-ROM Drive Microsoft Internet Explorer 5.01 or later is also required. Service Pack indicates a service pack provided by Microsoft Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and other countries. Pentium is a registered trademark of Intel Corporation. Motorized Actuators Introduction Types ELS EZS EZS Clean Room DRS DRL Motorized Linear Slides Motorized Cylinders Compact Linear Actuators ELC EZA DG Hollow Rotary Actuators E-101

5 Motorized Actuators Battery Set This battery is required to use the controller in the absolute mode. A dedicated battery holder is included. PAEZ-BT2H Specifications Mass: 0.18 kg D488 (37.2) 31.5± (5) : PAEZ-BT2H Battery Type Cylindrical Sealed Nickel-Cadmium Cell Nominal Voltage 2.4 VDC Rated Capacity 2000 mah Mass 180 g Service Life Approx. 4 years Charge Time 48 hours 1 Data Retention Period Approx. 360 hours (approx. 15 days) 1 4 Operating Ambient Temperature C (non-freezing) Operating Ambient Humidity 20 85% 1 At an ambient temperature of 20 C 2 Calculated by assuming the following conditions of use (one-week cycle) The battery is charged for 8 hours and used for 16 hours to back up data on six days in a week. The battery is used to back up data for all 24 hours on one day in a week. 3 The battery is not charged at the time of shipment. Charge the battery for at least 48 hours before using it. 4 After the power is cut off with the battery fully charged 15 (2-R18.6) 60± ± ± (79.2) (8-R2.25) For protection of the environment, please recycle used batteries. Bring expended batteries to your nearest Oriental Motor sales office. DIN Rail Mounting Plate Use this mounting plate when installing the linear motion controller to a DIN rail. (The mounting screws are included.) PADP DIN Rail Mounting Plate 49 Center of DIN Rail Included Mounting Screws: M3P0.5 Length 8 mm 3 pieces included E-102 ORIENTAL MOTOR GENERAL CATALOGUE

6 Customer Support Centre Singapore: , Malaysia: , Others: Dual Axis Mounting Brackets (Applicable Products: EZS Series) These are dedicated mounting brackets for using two axes of the EZS Series motorized linear slides. X-Y Mounting X-Z Mounting Z-Axis Motorized Actuators Features Dual Axis Combinations Can be Easily Implemented in the EZS Series Using the dedicated mounting bracket allows you to easily use EZS Series motorized linear slides in dual axis combination. Various combinations are available such as X-Y or X-Z. Available Combinations of Products X-Y Mounting X-Z Mounting X-Axis Y-Axis Transportable Mass (kg) X-Axis Z-Axis Transportable Mass (kg) EZS4D EZS3D 2.3 max. EZS4D EZS3D 3.ax. EZS6D EZS3D 5.7 max. EZS6D EZS3D 3.ax. EZS6D EZS4D max. EZS6D EZS4D 6.7 max. The maximum length of a linear slide for the second axis (Y or Z axis) is 300 mm. This is applicable to products with a 1m lead. Speed is reduced by half for products with a 6 mm lead. Specification values are based on those when the X-axis is mounted horizontally. This is not a product suitable for a clean room environment. Product Number Code PAB - S4 S3 R Y-Axis X-Axis X-Axis You Can Select an Appropriate Size under Our Custom- Design Program "FACE" As with the EZS Series, the size of the dual axis mounting bracket is also specifiable in increments of 10 mm. Simple Streamlined Wiring with Dedicated Cable Holder (Cable holder sold separately) Dedicated cable holders are available. 1 Dual Axis Mounting Bracket 2 First Axis Side Linear Slide S4: EZS4D S6: EZS6D 3 Second Axis Linear Slide S3: EZS3D S4: EZS4D 4 Combination Patterns R: R Type L: L Type 5 Stroke in Second Axis First axis side refers to the X-axis, while second axis refers to the Y- or Z-axis. 50 mm increments Combination of EZS4 and EZS3 Combination of EZS6 and EZS3 Combination of EZS6 and EZS4 R Type L Type R Type L Type R Type L Type PAB-S4S3R005 PAB-S4S3L005 PAB-S6S3R005 PAB-S6S3L005 PAB-S6S4R005 PAB-S6S4L005 PAB-S4S3R010 PAB-S4S3L010 PAB-S6S3R010 PAB-S6S3L010 PAB-S6S4R010 PAB-S6S4L010 PAB-S4S3R015 PAB-S4S3L015 PAB-S6S3R015 PAB-S6S3L015 PAB-S6S4R015 PAB-S6S4L015 PAB-S4S3R020 PAB-S4S3L020 PAB-S6S3R020 PAB-S6S3L020 PAB-S6S4R020 PAB-S6S4L020 PAB-S4S3R025 PAB-S4S3L025 PAB-S6S3R025 PAB-S6S3L025 PAB-S6S4R025 PAB-S6S4L025 PAB-S4S3R030 PAB-S4S3L030 PAB-S6S3R030 PAB-S6S3L030 PAB-S6S4R030 PAB-S6S4L mm increments Custom-Design Program "FACE" Numbers Stroke Specifiable in the Box mm mm mm mm mm Custom-design program "FACE" Combination of EZS4 and EZS3 Combination of EZS6 and EZS3 Combination of EZS6 and EZS4 R Type L Type R Type L Type R Type L Type PAB-S4S3R PAB-S4S3L PAB-S6S3R PAB-S6S3L PAB-S6S4R PAB-S6S4L Introduction Types ELS EZS EZS Clean Room DRS DRL Motorized Linear Slides Motorized Cylinders Compact Linear Actuators ELC EZA DG Hollow Rotary Actuators E-103