Section 5 Contents Accessories 5.02 Application Chart Accessories 5.03 RAM Mounts 5.07 Fork Level Indicator 5.11 Forklift Laser Guidance System 5.11 Forklift Covers & Enclosures 5.12 New Items: Work Assist Pole - p. 5.03 Fan Kits - p. 5.04 Storage Tray - p. 5.05 Laptop Holder - p. 5.10 Accu-Tilt - p. 5.11 Hard Wired Laser - p. 5.12 Forklift Enclosure - p. 5.12 Note: 1910.178(q)(5) (1998) of the Occupational Safety and Health Act (OSHA) requires that All parts of any such industrial truck requiring replacement shall be replaced only by parts equivalent as to safety with those used in the original design.
Accessories Accessories Application Chart Work Assist Accessories Accessory Clamp & Mounting Plate (RF) Adjustable Mounting Arm System Clamp, Accessory Clip Pad Clip Pad & Hook Clip Pad, Desktop Cup Holder Fan Fire Extinguisher Hook Hook, Utility Light Console Area Light, Dome Light, Flashing Light, Strobe Light, Work Mirror, Rear View Pocket Shrink Wrap Holder Shrink Wrap Tray Storage Module - Battery Cover Mount Storage Module - Magnetic Mount Storage Net Behind Seat Storage Tray, Upper or Lower Terminal Mounting Plate (RF) Tube Tube, Extended C-5 FC4000/4500 PC4500 PE4000/4500 PR4500 PW3500 RC5500 RR/RD5000/5200/5700, RM/RMD6000 SC4000/4500/5200 SH5500/SHR5500 SP3000/3200/3400/ 3500/4000 SR ST3000 SX3000 TR4500 TSP6000/6500/7000 WAVE WP3000 5.02 Crown One Source
Accessories Tubes 130879 149038 131380 131381 131414 131416 131960 141296 823238 Description Model 130879 Accessory Rail Kit LH or RH SP 3000 Series 149038 Work Assist Pole PC 4500 131380 Standard Work Assist Tube Kit PE 4000 Series 131381 Works Assist Tube Extension Kit PE/PR 4000 Series 143680 Standard Work Assist Tube Kit; PR 4500 Note: Electrical kit is P.N. 143681 131414 Right Tube Assembly Kit RR/RD 5000/S Series Description Model 131416 Work Assist Tube Kit RR/RD 5000/S Series 131960-001 TT Mast ST/SX 3000 131960-002 TL Mast ST/SX 3000 141296-001 84.5" Work Assist Tube Kit RC 5500 141296-002 88" Work Assist Tube Kit RC 5500 823238 Work Assist Tube Kit SR5200 Note: Plug for tubes is P.N. 124530 143840 Clamp 130145 143840-001 Used on C5 Pneumatic, 45º angle 130145 143840-002 Used on C5 Pneumatic, in line w/truck mtg Interface with RAM Mounting System + + + + + Clamp P.N. Arm P.N. Mounting 351094-XXX 351094-xxx Plate Optional Accessory The new Crown Ball Mount design (P.N. 351094-XXX) allows you to add the RAM mounting system to the Crown Work Assist clamps and accessories. The addition of the RAM mounting system allows you to position your accessories for the best access and prevent damage due to shock and vibration. See RAM mount pages 5.07-5.10. Terminal Mounting Plates 129572 130146 131417 131418 148748 126236-001, -002 & -003 814715 Description Model 126236-001 Mounting Bracket RR/RD 5000/S Series LXE 126236-002 Mounting Bracket RR/RD 5000/S Series Norand 126236-003 Mounting Bracket RR/RD 5000/S Series Telxon 129572 Adjustable Bar & RR/RD 5000/S Series Mounting Bracket #130146 Mounting Plate FC4000 Series, SC4000/5000 Series, SP3000/4000 Series, PE/PR4000 Series, RR/RD5000 Series, C5, TSP6000 /7000 Series #-Works with Crown RAM; includes clamps; needs hardware Description Model #131417 Universal Mounting Plate C5 Cushion, FC4000 Series, SC4000 Series, RC3000/RC5500, RM/RMD6000/S, SP3000 Series, PE/PR4000 Series, RR/ RD5000/S Series/ TSP6000/7000 Series #131418 Mounting Bracket C5 Cushion, FC4000 Series, SC4000 Series, RC3000/RC5500, RM/RMD6000/S, SP3000 Series, PE/PR4000 Series, RR/ RD5000/S Series, TSP6000/7000 Series #148748 Universal Terminal Mounting Kit 814715 Bracket Data Log ESR 4500/5000 C5 Cushion, FC4000 Series, SC4000 Series, RC3000/RC5500, RM/RMD6000/S, SP3000 Series, PE/PR4000 Series, RR/ RD5000/S Series/ TSP6000/7000 Series Note: Optional recommended ball mount size: 2.25" - P.N. 351094-003 Work Assist 5.03
Accessories Clip Pad 131415 Includes clamp 141462 Used on SH/SHR 5500 151743 Used on WP 3000 Note: Optional recommended ball mount size: 2.25" - P.N. 351094-003 Clip Pad, Clamp-On 146238 Used on PC 4500, E-Steer. Note: Optional recommended ball mount size: 2.25" - P.N. 351094-003 Clip Pad and Hook 130144 Includes clamp 141460 No clamp; includes plate to use on SH/SHR 5500 Note: Optional recommended ball mount size: 2.25" - P.N. 351094-003 Hook 131419 For use with RF, includes clamp 141463 Does not include clamp, includes plate used on SH/SHR 5500 Note: Optional recommended ball mount size: 1.5" - P.N. 351094-002 Note: Optional recommended ball mount size: 1" - P.N. 351094-001 Pocket 130868 Gray; includes clamp 125997-001 Gray; used on Wave; 1 pocket kit 125997-002 Gray; used on Wave; 2 pocket kit 141461 Gray; used on SH/SHR 5500 kit 151744 Orange; used on WP 3000 125502 Gray pocket only 141751 Orange pocket only Fire Extinguisher Kit 141187 Includes fi re extinguisher. Used on SC 4000/5000 Series, FC 4000 Series, C5 & RC 5500 Cup Holder, Clamp-On 145078 Used on PC 4500 E-Steer, FC 4000 Series, SC 4000 & 5000 Series, C5 Note: Optional recommended ball mount size: 1.5" - P.N. 351094-002 Adjustable Arm System Kit 136994 Note: Used on TSP 6000/7000 & SR Shrink Wrap Holder Kit - Mounts on Pole Model 145080 PC 4500 147205S SC 5200 Note: Optional recommended ball mount size: 2.25" - P.N. 351094-003 131368 (PE 4000) 140083 (RC 5500) Fan Kits Type Model 131388 24V PE 4000 140125 24V PE 4500, PR 4500 132781-002 24V ST/SX 3000 (Mounted on work platform) 141459 24V SH/SHR5500 127503-001 36V FC 4000 Series, SC 4000 Series 140083 36V RC 5500 150226 36V RM/RD 6000/S 127592-001 36V, w/drive Thru Overhead Guard FC 4000, SC 4000 Series 127592-002 48V, w/drive Thru FC 4000 Series Overhead Guard 127503-002 48V FC 4000 Series Note: Optional recommended ball mount size: 1.5" - P.N. 351094-002 Fan Only Type Model 127259-010 12V with switch C5 127259-007 24V with switch PE 4000 Series, ST/SX 3000, RR 5200 125755 24V with switch RC 3000 127259-004 24V without switch PE 4000 Series 127259-002 36V with switch SC 4000 Series, FC 4000 Series, RR 5200 127259-005 36V without switch FC 4000 Series, SC 4000 Series, RC 5500 127259-003 48V with switch FC 4000, TSP 6000 127259-006 48V without switch FC 4000 Series, TSP 6000 Fan & Worklight Kit 140127 24V without switch PE 4500AC, PR 4500 5.04 Crown One Source
Accessories Dome Light 123683 Used on RM/RMD 6000/S, RC 5500. Will also need to order plate 139555, 2 of 060030-010, 2 of 060059-034, 2 of 060061-038, 2 of 060062-027 and clamp 130145. Cup Holder, Bolt-On 145079 Used on PC 4500, E-Steer. Shrink Wrap Holder, Bolt-On 145081 Used on PC 4500, E-Steer Fire Extinguisher Kit - Drive Thru Rack 127591 Includes fi re extinguisher. Used on FC 4000 Series & SC 4000/5000 Series Storage Module - Battery Cover Mount 137513 Mounts to bolt-on load backrest 137514 Mounts to hinged load backrest Storage Tray Clip Pad, Bolt-On 146237 Used on PC 4500, E-Steer. Storage Module - Battery Cover Mount 115870 Tray only 117420 141042 Used on trucks with no load backrest; includes one long bracket Used on trucks with no load backrest; includes two side brackets 129988 Used on trucks with Flex Seat - FC 4000 series, SC 4000 series 129988-002 Used on trucks with Suspension Seat - FC 4500, SC 4500, SC 5200 Storage Tray Upper & Lower Kits 141228S Upper Storage Tray 141229S Lower Storage Tray Storage Module, Magnetic Mount 144441S Includes tray, magnet and hardware. Can put two together and put on pallet truck battery cover. Used on PC 4500, TR 4500. 132715 Replacement Magnet Note: U-clamps only, 127419 Clip Pad, Desktop 816658 Housing 814594 Spring 060062-003 Screw (qty. 2) Used on RC 5500 Shrink Wrap Tray 131379 Used on PE 4000 Series, PW 3500, PR 4500 Utility Hook 131036 Note: Includes two hooks and warning labels. Bracket Assembly for Mirror, Rear View 134212 Note: Used on TSP 6000/7000, SP 4000 Order Separately - Clamp 130145 - Screw 060061-022 (Qty.4) - Mirror 137670 Mirror Kit 130673 Note: Includes left- & right-hand brackets, 2 mirrors, and hardware to mount. Mounts on overhead guard. Used on C5, FC 4000/4500 & SC 4000/45000/5200. Work Assist 5.05
Accessories Storage Net Behind Seat 147005S Also order: - 4 inserts 060103-006 - 4 screws 060062-041 - 4 wall hooks 147008 Strobe Light Kit Color 131377-001 Amber 131377-002 Red 131377-003 Blue Flashing Light Kit 131378 Programmable Security Lock 130863-002 This keypad offers an enhanced level of security to deter unauthorized or untrained personnel from operating the vehicle. A four digit Personal Identifi cation Number can be assigned for up to 200 operators that use the vehicle. Supervisor can lockout vehicle through keypad and can program keypad to turn vehicle OFF automatically if vehicle is idle for prolonged periods. Power input is 15 amps externally fused, 48 volts maximum. Power output is 10 amps maximum. Operating temperature range is -40 to +85 degrees Celsius. Work Platform 133892 Accessories: Work Platform Tray (P.N. 133894) Used on ST/SX 3000 131376 (PE 4000) Front Worklight Kits Number Description Model 128921 Drive Thru Overhead Guard FC 4000 Series 129589 Standard Overhead Guard Mounted FC 4000 Series 127528-001 Drive Thru SC 4000 Overhead Guard 127532-001 Standard Overhead Guard Mounted SC 4000 Series *131376 Mounted on Work Assist Pole PE 4000 Series 140126 Mounted on Work Assist Pole PR 4500 & PE 4500 133896-002 Mounted on Work Assist Pole ST/SX 3000 *Does not include mounting brackets Snap-On Platform W x L (in) 131069-001 25 x 36.50 131069-002 25 x 42.50 131069-003 25 x 48.50 Used on ST/SX 3000 Remote Number Mast Type Application 132782-002 ST/SX 3000, TL Ground 132782-003 ST/SX 3000, TT Ground 133895-002 ST 3000, TL Mast Platform 133895-003 ST 3000, Sideshift, Platform TL Mast 133895-004 SX 3000, TL Mast Platform 133895-005 ST 3000, TT Mast Platform 133895-006 ST 3000, Sideshift, Platform TT Mast 133895-007 SX 3000, TT Mast Platform Tool Retractor 300114 Capacity 1.76-4.4 lbs. (0.8-2.0kg) Extended rope length - 5.5 ft. 5.06 Crown One Source
RAM Mounts Protect your electronic devices by using the RAM Mounting System. RAM mounts utilize a patented rubber ball and socket design which isolates and dampens shock and vibration up to 50G of shock. Adjustable positioning features can not be matched by another mounting method. Mounting bases quickly attach and fi t every OEM lift cage or overhead guard made. All backed by a lifetime manufacturer's warranty. Made in USA. 1" Ball Holds up to 2 lbs 1.5" Ball Holds up to 4 lbs 2.25" Ball Holds up to 10 lbs How to Order: + + + = Vehicle Attachment Vehicle Attachments Arm Adapter Holder Assembly Crown Ball Base Rubber ball connected to oval base with mounting holes aligned to work with Crown Accessories. See pages 5.03 & 5.04.. No. Description 351094-001 1" ball with 2.52" x 1.85" oval base 351094-002 1.5" ball with 2.52" x 1.85" oval base 351094-003 2.25" ball with 2.52" x 1.85" oval base 2.5" Diameter Magnetic Base Has pre-drilled holes, including the AMP's hole pattern. The magnetic base contains 3 rare earth magnets that hold fi rm to ferrous metals. The adapter designed to conceal the magnets is made of a durable plastic composite to prevent scratching the mounting surface. Description 351095-011 1" ball Round Base with Rubber Ball Consists of a rubber ball connected to a fl at round base. This mount has pre-drilled holes, including the universal AMPS hole pattern. Description 351095-006 1" ball with 2 7 16" diameter base 351095-007 1.5" ball with 2 1 2" diameter base 351095-008 2.25" ball with 3 11 16" diameter base 351095-009 2.25" ball with 3 11 16" diameter base, reinforced steel V Base Ball and Straps Fits circular and square rails from 1" to a max of 2.1" diameter. To mount, place the saddle shaped plate on the rail then wrap the metal clamp strap around the rail and plate. Tighten the screw knob on the metal strap with a screw driver until the strap has a fi rm hold on the rail. Description 351095-021 1" ball 351095-022 1.5" ball 3.25" Diameter Suction Cup Suction cup designed to have an extra hold on any smooth, non-porous surface. For best results mount the suction cup on glass or non-porous plastic surface. Description 351095-010 1" ball Diamond Drill Down Base with Rubber Ball Consists of a 1" diameter rubber ball connected at right angles to a 2.43" x 1.31" diamond base. The base has 2 holes 1.912" from center to center, matches the industry standard AMP's hole pattern and will connect to a large variety of RAM mount and third party cradles. Description 351095-018 1" ball Work Assist 5.07
Vehicle Attachments Rubber Ball with Clamp Base - 4" Fits on square rails up to 4" wide and 2 1 8" deep. Can fi t much smaller rails if needed by angling. Description 351095-001 1" ball 351095-002 1.5" ball 351095-003 2.25" ball Rubber Ball with Clamp Base - 2.5" Fits on square rails up to 2.5" wide. Description 351095-004 1.5" ball 351095-005 2.25" ball Measure upright support as shown in image. Select clamp base which most closely matches the widest dimension. Overhead Guard Mount The Overhead Guard Mount is the ideal way to get a ball attached to most any lift cage or overhead guard. Utilizing two identical plates of stamped steel with numerous common hole patterns and slots makes attachment a breeze. Two popular ball sizes: 1.5" & 2.25" diameter may be attached to the same plate for multiple applications. Installation is as easy as attaching the base with ball to one of the plates and then sandwiching the guard or cage between the two mounting plates using the hardware provided. Requires a square base: 1.5" ball (P.N. 351095-012) or 2.25" ball (P.N. 351095-013 or P.N. 351095-014). 351095-019 Arms Double Ball Socket Arm, Short The short double socket arm, has a socket at both ends that fi ts ball bases. RAM socket technology allows for almost infi nite adjustment and perfect viewing angles. Works With Overall Length 351095-027 1" ball 2.38" 351095-028 1.5" ball 3.5" 351095-029 2.25" ball 5.0625" Double Ball Socket Arm, Standard Has socket at both ends that fi ts ball bases. A single spring inside the arm opens the end sockets, allowing you to pivot the ball and socket connection. Allows for almost infi nite adjustment and perfect viewing angles. Works With Overall Length 351095-024 1" ball 3.69" 351095-025 1.5" ball 5.625" 351095-026 2.25" ball 8.375" Double Ball Socket Arm, Long Has a socket at both ends that fi ts ball bases. A single spring inside the arm opens the end sockets, allowing you to pivot the ball and socket connection. This socket technology allows for almost infi nite adjustment and perfect viewing angles. Works With Overall Length 351095-030 1" ball 6" 351095-031 1.5" ball 9.125" 351095-032 2.25" ball 12.875" Adjustable Socket with Octagon Socket Consists of double 1" diameter open ball sockets with a 360 rotation point at the center & a connecting swivel joint that rotates forward and back 180. The rubber ball and socket at either end, and a central pivot point provides unsurpassed adjustability. The RAM ball sockets maximize ball coverage for optimal fi t. Works With Overall Length 351095-033 1" ball 6.25" 5.08 Crown One Source
Adapters Round Base with Rubber Ball Consists of a rubber ball connected to a fl at round base. This mount has pre-drilled holes, including the universal AMPS hole pattern. Description 351095-006 1" ball with 2 7 16" diameter base 351095-007 1.5" ball with 2 1 2" diameter base 351095-008 2.25" ball with 3 11 16" diameter base 351095-009 2.25" ball with 3 11 16" diameter base, reinforced steel Square Base with Rubber Ball Rubber ball, connected to a 4.75" square plate with 4x100mm holes and 4x75mm holes in each corner. Description 351095-012 1.5" ball 351095-013 2.25" ball 351095-014 2.25" ball (reinforced steel) Square Base with Rubber Ball Rubber ball, connected to a 3.625" square plate with a 75x75mm VESA hole pattern. The rubber ball is positioned 0.88" from the center of one edge. Description 351095-015 1.5" ball 351095-016 2.25" ball Diamond Drill Down Base with Rubber Ball Consists of a 1" diameter rubber ball connected at right angles to a 2.43" x 1.31" diamond base. The base has 2 holes 1.912" from center to center, matches the industry standard AMP's hole pattern and will connect to a large variety of RAM mount and third party cradles. Description 351095-018 1" ball Holders X-Grip Universal Holder Has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. Dimensions: width - 1.875" - 3.25", depth 0.875". No ball base adapter required. Description 351095-034 1" ball X-Grip Universal for 5" Phablets Has a clean and clever four leg design that sports great holding power without hiding your phone or phablet behind foam pads and plastic. Compatible and interchangeable with a wide range of mounts. Dimensions: width 1.75"-4.5". No ball base adapter required. Description 351095-035 1" ball 351095-037 Tough-Claw with X-Grip Holder Tough-Claw base and universal X-Grip holder. The X-Grip holder has a clean and clever four-leg design that sports great holding power without hiding your smartphone behind foam pads and plastic. 351095-052 Power-Grip Universal Scanner Gun Cradle Compatible with a wide range of ruggedized 2D barcode scanners. Accommodates pistol grip scanner guns with a maximum pistol grip of 1.4". Internal dimensions 3.47" x 2.16" x 4.9". Requires ball adapter 351095-007. 351095-036 Universal Finger-Grip Phone/Radio Holder Designed to hold a large amount of cell phones & electronic devices comes with 3 sets of 4 fl exible rubber coated fi ngers placed along sides to grip your device. Fingers open by squeezing ends to open small fi nger arms. Bottom of the holder includes back plate that adds support to the device being held by the mount. Spine plate contains universal AMPs and 1.5" x 2" hole patterns. Min/Max with top & bottom plates: Height 5.25" to 6". Plates can be removed for larger devices. Requires ball base adapter 351095-007. RAM-X-Grip III Universal Clamping Cradle for 10" Tablets Spring loaded holder for large tablets, with or without a case. Accommodates netbooks as well. Dimensions: Tray Depth Tray Thickness Tray Width (Expansion) Side Clamp Arm Height 6.0" 1.0" 8.56" - 11.12" 2.75" max 351095-045 No ball base adapter required. 351095-039 Universal Holder for Scanner Guns and Handheld Computers Specially designed cradle that will hold most types of gun scanner handles. On the side of the cradle is a spring loaded lever that will securely hold the gun scanner in the cradle. Designed for pistol grip scanners. Requires ball base adapter 351095-007. 351095-042 Tab-Tite Kit for Large Tablets Fits most 10" tablets. Includes 2 sets of interchangeable cups to give the user a custom fi t. Spring loaded. Cradle dimensions: Height Max. Width Max. Edge Depth 8.50" - 10.75" 7.75" 0.56" 8.75" - 10.75" 8.25" 1.10" Requires ball base adapter 351095-007. Work Assist 5.09
Holders Holders Tab-Lock Kit for Large Tablets Same as 351095-042 except locks for theft deterrent. Cradle dimensions: Height Max. Width Max. Edge Depth 8.00" - 10.25" 6.80" 0.50" 8.25" - 10.25" 7.75" 0.56" Requires ball base adapter 351095-007. 351095-043 Tab-Tite Kit for Small Tablets Fits most 7-8" tablets. Includes 3 sets of interchangeable cups to give the user a custom fi t. Spring loaded retention to hold device securely on the forklift. It is compatible with the following tablets with or without skins, sleeves or cases: Archos 7, Asus EEE Pad Memo, Asus Tough-ETBW11AA, Barnes & Nobel NOOKcolor, BlackBerry Playbook, Dell Streak 7, HTC Flyer, Google Nexus 7, Samsung Galaxy. Cradle is compatible with any tablet that will fi t the dimensions listed below. It is important to verify the dimensions of your tablet with a case/sleeve/skin when determining the overall size. Cradle dimensions: Height Max. Width Max. Edge Depth 6.80" - 9.000" 5.31" 0.125" - 0.56" 7.00" - 9.100" 4.70" 0.125" - 0.44" 7.30" - 9.620" 5.31" 1.06" Requires ball base adapter 351095-007. 351095-040 Features: 1. Support cups contain open slots to fi t tablets of various sizes 2. Back plate can support various size support cups 3. Spring loaded tension provides secure support for your tablet 4. Spring loaded cradle allows for quick release of your tablet 5. Full access to all ports 351095-046 351095-044 351095-051 Universal X-Grip II Tablet Holder with 1.5" Ball for Small Tablets Four leg design has great holding power and does not hide your tablet behind foam pads or plastic. Spring loaded holder and 1.5" rubber ball connect to the back of the base. Includes extra easy access grip knobs located on the back of the holder for quick release of your tablet. This holder expands and contracts for perfect fi t of most 7" tablets. Min. Width Max. Width Depth 2.25" 5.75" 0.875" Note: Devices 2.25" in width must be a minimum of 7" in height to fi t. No ball base adapter required. Universal Laptop Mount Tough Tray II Spring loaded holder for large tablets, with or without a case. Accommodates netbooks as well. Dimensions: Tray Tray Tray Width Side Clamp Depth Thickness (Expansion) Arm Height 6.0" 1.0" 8.56" - 11.12" 2.75" max Requires ball base adapter 351095-007. Universal Laptop Tough Tray Holder with Flat Retaining Arm Spring loaded expandable tray that accommodates 10 to 16 inch wide laptops. Includes four fl at side clamping arms that allow your laptop to close completely while in the tray. These arms can be moved both vertically and horizontally allowing for a custom fi t for varying thicknesses of laptops and the freedom of not blocking ports or drives. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS, PDAs or other electronics. Tray Tray Depth Thickness Side Clamp Arm Height 10.0" 2.125" 0.5" to 1.75" Tab-Lock Kit for Small Tablets Same as 351095-040 except locks for theft deterrent. Cradle dimensions: Height Max. Width Max. Edge Depth 6.55" - 9.80" 5.31" 0.125" - 0.56" 6.75" - 9.90" 4.70" 0.125" - 0.44" 7.05" - 10.42" 5.31" 1.06" Requires ball base adapter 351095-007. 351095-041 Locking Knob - Locks the Arms Includes a brass thread for 1" or 1.5" socket arms, thus allowing you to disengage the screwing of the knob. Once you have set your mount in the location you need, you can lock it in place and feel safe that your mounted device will stay right where you left it. Thread Size Works With 351095-047 1 4" - 20 thread 1" ball arm 351095-048 5 16" - 18 thread 1.5" ball arm Mount Assembly Universal Mount with 2 Round Bases Consists of one double socket arm and two round bases that contain the universal AMP's hole pattern. Has adjustment points at both ends of the double socket arm; this allows for almost infi nite adjustment and perfect viewing angles. The hole pattern found on the round base adapter will connect to many RAM cradles, including all ipad cradles. Ball Base Double Socket Arm Overall Height Ball Size 144357 351095-006 351095-027 5" 1" 351095-051 351095-007 351095-025 7.35" 1.5" 5.10 Crown One Source
Fork Level Indicator 340402 Accu-Tilt Accu-Tilt is a Fork Tilt Level Indicator that is made for all makes and models of lift trucks. The Accu-Tilt shows the operator the level of the forks at all times thereby reducing potential damage by piercing product or racking and increasing productivity by eliminating the guess work. Additionally, the Accu-Tilt s Fork Tilt Level Indicator will also indicate to the operator the correct fork angle to travel with a load as well as parking the lift truck. Forklift Laser Guidance System The Forklift Laser Guidance System provides operators a continuous visual reference of fork position which aids in increasing safety, accuracy, and productivity, while reducing product damage. The laser projects a line or dot onto the pallet or product indicating the level of the forks which allows operator heightened visibility and more accurate fork placement. Laser Models: Basic Standard - Basic standard Cold Storage - Designed for low-temperature and high-moisture environments Height Control - Designed only to operate at 7' and above Laser Types: Line - Best for low-light areas such as warehouses Dot - Best for cold storage and outdoor usage Features: Contains two rechargable nickel metal hydride batteries Charger included Shuts off after 4 mins without movement, saving battery life Automated vibration controlled start INSTALL IN LESS THAN 5 MINUTES Heavy duty Self contained Quick battery change Mounting: Single laser, dual laser, and hard wired series units mount directly to the forklift carriage in less than fi ve minutes. Fork mount laser units attach to the fork directly. Batteries: 50+ continuous hours of life per battery Quick charge 3 hours; full charge in 8 hours Batteries are double shrink wrapped for durability Forklift Laser Guidance Systems Laser Series Power Source Laser Type Description Water Resistant Seal Cold Storage Height Control Single Battery Dot 351093-001-D Basic Std Single Battery Dot 351093-002-D Cold Storage - Water Resistant Single Battery Dot 351093-003-D Height Control Single Battery Dot 351093-007-D Basic Std - Fork Mount Single Battery Dot 351093-008-D Cold Storage - Water Resistant - Fork Mount Single Battery Dot 351093-009-D Height Control - Fork Mount Single Battery Dot 351093-019-D Height Control - Cold Storage - Water Resistant Single Battery Line 351093-001 Basic Std Single Battery Line 351093-002 Water Resistant Single Battery Line 351093-003 Height Control Single Battery Line 351093-007 Basic Std - Fork Mount Single Battery Line 351093-008 Water Resistant - Fork Mount Single Battery Line 351093-009 Height Control - Fork Mount Single Battery Line 351093-019 Height Control - Water Resistant Single Hard Wired Dot 351093-012-D Basic Std Single Hard Wired Dot 351093-013-D Cold Storage - Water Resistant Single Hard Wired Dot 351093-014-D Height Control Single Hard Wired Dot 351093-015-D Height Control - Cold Storage - Water Resistant Single Hard Wired Line 351093-012 Basic Std Single Hard Wired Line 351093-013 Water Resistant Single Hard Wired Line 351093-014 Height Control Single Hard Wired Line 351093-015 Height Control - Water Resistant Dual Battery Line & Dot 351093-004 Basic Std Dual Battery Dot & Dot 351093-005 Cold Storage - Water Resistant Dual Battery Line & Dot 351093-006 Height Control Dual Battery Dot & Dot 351093-020 Height Control - Cold Storage - Water Resistant Dual Hard Wired Line & Dot 351093-016 Hard Wired - Basic Std Dual Hard Wired Dot & Dot 351093-017 Hard Wired - Cold Storage - Water Resistant Dual Hard Wired Line & Dot 351093-018 Hard Wired - Height Control Fork Mount Work Assist 5.11
Forklift Laser Guidance System Single Laser Series Number Description Laser Type 351093-001 Basic Std Line 351093-001-D Basic Std Dot 351093-002 Water Resistant Line 351093-002-D Cold Storage - Water Resistant Dot 351093-003 Height Control Line 351093-003-D Height Control Dot 351093-019 Height Control - Water Resistant Line 351093-019-D Height Control - Cold Storage - Water Resistant Dot Fork Mount Laser Series Number Description Laser Type 351093-007 Basic Std Line 351093-007-D Basic Std Dot 351093-008 Water Resistant Line 351093-008-D Cold Storage - Water Resistant Dot 351093-009 Height Control Line 351093-009-D Height Control Dot Fork mount lasers are designed for the non-standard fork carriages. Lasers are mounted directly to the fork of the lift truck. Dual Laser Series Number Description Laser Type 351093-004 Basic Std Dot & Line 351093-005 Cold Storage - Water Resistant Dot & Dot 351093-006 Height Control Dot & Line 351093-020 Height Control - Cold Storage - Dot & Dot Water Resistant 351093-016 Hard Wired - Basic Std Dot & Line 351093-017 Hard Wired - Cold Storage - Water Resistant Dot & Dot 351093-018 Hard Wired - Height Control Dot & Line The dual laser feature is designed for repetitive moving of product. This feature incorporates two distinct lasers to aid the operator. The fi rst laser directs the forks into the pallet and the second laser guides the pallet onto the rack. Accessories Description 351093-010 Rechargable NIMH Batteries 351093-011 Solid-State Charger 351093-022 Face Plate Assembly 351093-023 Power Plug Adapter (works in Australia, China & New Zealand) Hard Wired Laser Series Number Description Laser Type 351093-012 Basic Std Line 151093-001 Basic Std - Orange; includes cable and deutsch connector Line 351093-012-D Basic Std Dot 351093-013 Water Resistant Line 351093-024 Water Resistant - Orange; includes cable and deutsch Line connector 351093-013-D Cold Storage - Water Resistant Dot 351093-014 Height Control Line 351093-014-D Height Control Dot 351093-015 Height Control - Water Resistant Line 351093-015-D Height Control - Cold Storage - Water Resistant Dot Oil and water resistant wires are hard wired directly into truck battery with voltage systems between 12-55 DC. Matching pigtails are provided for power connection. (Wiring for mast not included.) Experienced personnel are recommended for self-installation. Forklift Covers & Enclosures Forklift Enclosures - Atrium Number Description Size 300125-001 Standard - Super Clear Vinyl Fits up to 6,000 lbs 300125-002 Large - Super Clear Vinyl Fits 6,000-12,000 lbs 300125-006 XL - Super Clear Vinyl 12,000 lbs+ Great for the yard and warehouse. Keeps the rain or dust away from the operator. Zippered doors can be shut or unzipped and folded back into place while working. Universal for most lifts. UV yellow inhibitor. Freeze point fl exibility. Marine grade stitching. Attaches in seconds. Super clear material. Forklift Storage Cover Number Description Size 300125-005 Forklift Storage Cover Fits up to 8,000 lbs 100"L x 45"W x 80"H This is manufactured from the most durable fabrics and is great for the yard or warehouse, keeping your lift s resale value high. Slips on in seconds. Get a better resale value. Easy access zipper. Strong, durable non-rip fabric. Anti-loft/anti-moisture vents. Sizing straps for secure fi t. Strong elastic bottom hem. Forklift Cap Covers Number Description Size 300125-003 Super Clear Tinted Vinyl 52.5" L x 46" W 300125-004 Super Clear Vinyl 40" L x 45.5" W Attaches with built-in bungee cords; just wrap around roof poles and attach back to itself. Attaches in seconds. Fits all lifts. Super clear material. Absorbs impacts. Protection from sun (tinted version only). Protection from rain and falling debris. Great for all warehouses and yards. ATTACHES IN SECONDS, FITS ALL LIFTS 5.12 Crown One Source
PROTECT YOUR OPERATOR WITH CROWN S DURABLE SOFT CABIN Work Assist st MAXIMUM FLEXIBILITY AND VALUE IN ANY APPLICATION You need to keep your product moving in unpredictable weather conditions. Rely on Crown s C-5 Series with soft cabin to protect your operators because when operators are comfortable, productivity increases. Crown s C-5 Series with soft cabin protects your largest investment your operators during changing weather conditions without compromising visibility and safety. Work Assist 5.13
KEEP YOUR PRODUCT MOVING WITH C-5 SERIES SOFT CABIN Our modular soft cabin construction enables you to select a customized solution with the following features... Safety glass windshield with wiper and washer Acrylic top Soft side zipper style doors and rear window can be rolled up or down as weather conditions change These options are available when you purchase a new truck or as an aftermarket add-on. Safety glass windshield with wiper and washer kit - 154633 Acrylic top kit - 154631 Soft rear window kit - 154634 Soft left and right doors kit - 154632 Entry assist handle kit - 151482 Harness kit - 151573 VISIT CROWN.COM Order all kits OR for CALL a full cabin YOUR LOCAL CROWN DEALER FOR MORE DETAILS. PROTECT Y0UR LARGEST INVESTMENT AND KEEP YOUR PRODUCT MOVING WITH CROWN'S C-5 SERIES WITH SOFT CAB. VISIT CROWN.COM OR CALL YOUR LOCAL CROWN DEALER FOR MORE DETAILS. 5.14 Crown One Source