MANHATTAN STORAGE BED PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction. Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not destroy any of the packaging until you are certain that you have all the necessary parts for the assembly. Please ensure that the packaging is disposed of in a safe environmentally friendly way. CAUTON: There are small components used in the construction of this unit. These loose items should be kept away from young children whilst assembling your unit to avoid the danger of choking hazards. Parts dentification B A A B 6 0 9 Drawer x 8 Note: Standard wooden slat frame (part ) Upgraded sprung slat frame (part ) Parts Checklist Ref. Ref. Headboard Footboard Side Rail Wooden Slats set Metal Sprung Slat System* frame 6 Drawer Front Panel Drawer Side Panel 8 Drawer Front Panel ii 9 Drawer Bottom Panel 0 Drawer Back Panel A Adjustable Support Leg B Adjustable Support Leg Bottom Support Rails Bottom Support Rails Page of 6 *Only supplied if upgraded sprung system chosen
Fittings Checklist Code Code G Flat Washer (6mm) A Bolt (M8x0mm) H Allen Key (mm) x B Spring Washer (8mm) Plastic Nut Screw (x0mm) C Flat Washer (8mm) x K Screw (x0mm) x0 L Screw (x0mm) D Allen Key (mm) x M Bolt (M8xmm) N Wheel x0 E Bolt (M6x0mm) F Sleeve Nut (M6xmm) Note: The following fittings will be found in the box which contains the sprung slat Frame. They are not in the assembly kit for the bed itself. O Bolt (M6xmm) P Slat Centre Support Leg x Q Slat Support Legs x Additional Tools Required Care & Maintenance Crosshead Screwdriver n the unlikely event of missing or damaged parts, please contact the customer service team on 08 90000. When calling this number, please quote the part code reference numbers shown in this leaflet when requesting spare or replacement parts. General Hints & Tips When Please retain your Assembly nstruction and tools provided, for future use. Periodically check that all bolts are still tight. This assembly requires two people. ntersecting Hole Page of 6 fitting barrel nuts into the panels, ensure they are fitted the correct way so the hole is facing towards the intersecting hole. We recommend the bed is assembled in the room it will be located in.
A B C C B A 0mm Fit the bolts (A), spring washers (B), and flat washers (C) to the holes in the headboard () and footboard () as shown. Note: Do not fully locate the bolts, but leave 0mm protruding. Fit the side rails () to the headboard and footboards locating the fixing brackets behind the flat washers. Once all four corners are located check the bed is square, then fully tighten the bolts using the allen key (D). M C M C ARROWS ON LABELS PONT TO EACH OTHER A A B A B Fit pairs of adjustable support legs to side rails (A &B) - fix them into pre-threaded holes with bolt/washer (M&C). Page of 6
BED SLAT FXNG E G F Lay the set of slats () onto the slat support rails on the side rails. Align the first and last slat with the end of the rails, and secure in place using the bolts (E), washers (G) and sleeve nuts (F). Fully tighten using the allen key (H). Use all of the bolt sets provided (E, F & G). Once secure fix the centre slat using the bolts as before. a UPGRADE SPRUNG SLAT SYSTEM E x G x Q O F x Open the metal frame and lay face down on the working surface. P Fit the support legs (P & Q) to the positions shown, securing with the bolts (O). Fully tighten using the allen key (H). Q Carefully turn the slat frame over, and position onto the slat support rails. Align the frame with the fixing holes at each end and secure using the bolts (E), washers (G) and sleeve nuts (F). Fully tighten using the allen key (H). Use x of the bolt sets provided (E, F & G). Finally, please ensure that all bolts are fully tightened before the bed is used. ETHER OR WLL BE SUPPLED - BOXED SEPARATELY Page of 6
DRAWER ASSEMBLY a: 8 b: 9 MPORTANT: MAKE SURE WHEN YOU FT THE NUTS THAT THE HOLE S N THE CORRECT ALGNMENT c: + 0 K x x x0 N x0 K N Page of 6
6 DRAWER ASSEMBLY L FOLLOW LNE ON BACK OF DRAWER FRONT PANEL 6 L SLOT N THE DRAWERS Page 6 of 6