Instruments Technical Support Via del pozzo, 5 Loc. S.Martino Monteriggioni Siena ITALY Date: 25/09/2008 Author :MICHELE MELONI R&D Dept.

Size: px

Start display at page:

Download "Instruments Technical Support Via del pozzo, 5 Loc. S.Martino 53035 Monteriggioni Siena ITALY Date: 25/09/2008 Author :MICHELE MELONI R&D Dept."

Rachel Hood
8 years ago
Views:

1 Pag 1/8 - Software Update rel Installing 2.21 in VesMatic Cube 200. This procedure allows the software update from version 2.20 to For the update of the instrument is necessary to install such software ver (vescube.exe) and to update two Firmware. Device 0x07 sorter with firmware Sorter_V3.10.HEX Device 0x15 transfer Left with firmware Transfer_V3.09.HEX PREPARATION OF COMPACT FLASH You can download the software called Install221.zip at the following address : Please note that access to the site is submitted to a password ; in case you do not have your password please contact salesoffice@diesse.it After downloading unpack the file. Zip in a compact flash ; it is not necessary to create a specific directory. File compact flash PROCEDURE Start the instrument and insert the compact flash with the Setup program in the high slot on the right side of the tablet.

HEX PREPARATION OF COMPACT FLASH You can download the software called Install221.zip at the following address : http://www.diesse.

2 Pag 2/8 - PROCEDURE UPDATE VER Entering the service of the instrument following the steps in the picture: SETTINGS SERVICE Password "111111" Select the button SwUpdate to launch SwUpdate program

21 Entering the service of the instrument

3 Pag 3/8 - On screen program select the installation upgrade process called Install Vescube V221 Press OK to start the installation At the end of installation press EXIT; at this point will restart the program of the instrument that will correspond to version 2.21 CAUTION: The program may be shared but not visible, windows as shown on the right picture. therefore, to consider closing the display of folders with the key X

of the instrument that will correspond to version 2.

4 Pag 4/8 - PROCEDURE FOR FIRMWARE UPDATE ( STEP 1) Entering the service of the instrument following the steps in the picture: SETTINGS SERVICE Password "111111" Select the button SwUpdate to launch SwUpdate program

steps in the picture: SETTINGS SERVICE Password

5 Pag 5/8 - On screen program select the installation upgrade process called Install Vescube Firmware Press OK to start the installation At the end of installation press EXIT; at this point will restart the program of the instrument that will correspond to version 2.21 CAUTION: The program may be shared but not visible, windows as shown on the right picture. therefore, to consider closing the display of folders with the key X

6 Pag 6/8 - PROCEDURE FOR FIRMWARE UPDATE ( STEP 2) Entering the service of the instrument following the steps in the picture: SETTINGS SERVICE Password "222222"

7 Pag 7/8 - Procedure update Device 0x07 sorter with firmware Sorter_V3.10.HEX In Firmware screen select the device 0x07 Sorter Press th button Write to dev and after Set Filename. Select Sorter_V3.10 and confirm pressing OK. Press the button Download Fw and wait the O.K. message ( yellow ) in the label called Download Status.

and after Set Filename. Select Sorter_V3.10 and confirm pressing OK.

8 Pag 8/8 - Procedure update Device Device 0x15 transfer Left con with firmware Transfer_V3.09.HEX In Firmware screen select the device 0x15 transfer Left Repeat the same sequence of operations described for the sorter remembering to select the firmware Transfer_V3.09. CAUTION : Check in column Current Firmware Version the new firmware release.

HEX In Firmware screen select the device 0x15 transfer Left Repeat the same sequence

Service Bulletin [2014 02]

Service Bulletin [2014 02] How do you know if you have a PanelView Plus or a Panelview Plus 6? The quickest way is to look at the type of memory slot the unit has on the back. If it accepts and SD Card, it s a PanelView Plus 6.