BLACK BOX Works with the Black Box ServReach KVM Gate (KVIP1000A), ServReach KVM Cube (KVIP1001A), or as a standalone device.

Transcription

1 PRP1000A Power Reboot Pod User s Manual Switch on or off, or power cycle 1 to 99 servers. BLACK BOX Works with the Black Box ServReach KVM Gate (KVIP1000A), ServReach KVM Cube (KVIP1001A), or as a standalone device. Customer Support Information Order toll-free in the U.S.: Call BBOX (outside U.S. call ) FREE technical support 24 hours a day, 7 days a week: Call or fax Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA Web site: info@blackbox.com

2 Power Reboot Pod User s Manual Federal Communications Commission and Industry Canada Radio Frequency Interference Statements This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturer s instructions, may cause inter ference to radio communication. It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference. Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. This digital apparatus does not exceed the Class A limits for radio noise emis sion from digital apparatus set out in the Radio Interference Regulation of Industry Canada. Le présent appareil numérique n émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le brouillage radioélectrique publié par Industrie Canada. Page blackbox.com

3 NOM Statement Instrucciones de Seguridad (Normas Oficiales Mexicanas Electrical Safety Statement) 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura. 3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas. 4. Todas las instrucciones de operación y uso deben ser seguidas. 5. El aparato eléctrico no deberá ser usado cerca del agua por ejemplo, cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc. 6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el fabricante. 7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante. 8. Servicio El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser referido a personal de servicio calificado. 9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá, alfombra o superficie similar puede bloquea la ventilación, no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilación. 10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como radiadores, registros de calor, estufas u otros aparatos (incluyendo amplificadores) que producen calor. 11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo de operación, o como se indique en el aparato. 12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada. 13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos, poniendo particular atención a los contactos y receptáculos donde salen del aparato. 14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones del fabricante. 15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de energia. 16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo. 17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilación. 18. Servicio por personal calificado deberá ser provisto cuando: A: El cable de poder o el contacto ha sido dañado; u B: Objectos han caído o líquido ha sido derramado dentro del aparato; o C: El aparato ha sido expuesto a la lluvia; o D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o E: El aparato ha sido tirado o su cubierta ha sido dañada blackbox.com Page 3

4 Power Reboot Pod User s Manual Trademarks Used in this Manual Black Box and the Double Diamond logo are registered trademarks, and ServReach is a trademark, of BB Technologies, Inc. Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners. We re here to help! If you have any questions about your application or our products, contact Black Box Tech Support at or go to blackbox.com and click on Talk to Black Box. You ll be live with one of our technical experts in less than 30 seconds. Page blackbox.com

5 Table of Contents Table of Contents 1. Specifications Overview Introduction The Power Reboot Pod System What s Included Installation Pre-Installation Guidelines Connecting the Power Reboot Pod (Standalone) Connecting a Power Reboot Pod to the ServReach KVM Gate (KVIP1000A) Connecting a Power Reboot Pod to the ServReach KVM Cube (KVIP1001A) Operation LED Indicators on the Power Reboot Pod Using the Power Reboot Pod Management Utility Operating the System...16 Appendix A. RS-232 Control Protocol...17 Appendix B. Serial Port Pinout blackbox.com Page 5

6 Power Reboot Pod User s Manual 1. Specifications Baud Rate: 1200 bps Distance: 12.8 to 25.6 ft. (4 to 8 m) Connectors: Input: C14 receptacle; Output Power Cable: C13 receptacle with 150 cm cable Communication Ports: IrDA Transmit and Receive Indicators: (1) green LED for input power status: (1) red LED for output power status Temperature Tolerance: Operating: 32 to 122 F (0 to 50 C); Storage: 5 to 122 F (-15 to +50 C) Humidity Tolerance: 0 to 95% Power: Input: VAC, Hz; Output Current: 10 amps Plastic Enclosure Size: Basic unit: 3.6"H x 1.68"W x 1.16"D (9.2 x 4.2 x 3 cm) Page blackbox.com

7 Chapter 2: Overview 2. Overview 2.1 Introduction The Power Reboot Pod is a unique power cord with a zero U form factor. It can switch on and off, and power cycle 1 to 99 servers via serial commands. The Power Reboot Pod works with the Black Box ServReach KVM Gate (KVIP1000A), ServReach KVM Cube (KVIP1001A), or as a standalone device. 2.2 The Power Reboot Pod system Figure 2-1 illustrates the Power Reboot Pod system, showing the Power Reboot Pods connected to servers and to the ServReach KVM Gate (KVIP1000A). KVIP1000A LAN/WAN KVM switch User over IP Server 1 Server 2 Server 3 Server 4 Power Reboot Pods 2.3 What s Included The Power Reboot Pod system comes with: (1) Power Reboot Pod (1) transmitter Figure 2-1. Power Reboot Pod + ServReach KVM Gate configuration. (1) RJ-45 to RJ-11 transmitter cable for ServReach KVM Gate (connects the KVIP1000A with the Power Reboot Pod) (1) rackmount bracket blackbox.com Page 7

8 Power Reboot Pod User s Manual 3. Installation 3.1 Pre-Installation Guidelines Switch off the computers you will connect with Power Reboot Pods. 3.2 Connecting the Power Reboot Pod (Standalone) Connect the Power Reboot Pod as illustrated in Figure Slide the transmitter into the slot on the side of the Power Reboot Pod furthest away from the LEDs. Make sure the arrows on the transmitter and Power Reboot Pod are facing each other. 2. Connect the serial cable s RJ-11 connector to the transmitter port and connect the serial cable s RJ-45 connector to the server s serial port using an RJ-45 to serial connector converter. 3. Connect the Power Reboot Pod s cable to the server s power port. 4. Connect the supplied cable to the Power Reboot Pod and to a power outlet. The Power Reboot Pod can work on 220 VAC or 110 VAC. RJ-45 To server s serial port Transmitter slotted into the Power Reboot Pod Serial cable RJ-11 To transmitter port To power outlet To Power Reboot Pod Power Reboot Pod Figure 3-1. Connecting the Power Reboot Pod. To server s power port 3.3 Connecting a Power Reboot Pod to the ServReach KVM Gate (KVIP1000A) Connect to the ServReach KVM Gate using the Power Reboot Pod Transmitter as follows: 1. Slide the transmitter into the slot of the Power Reboot Pod furthest away from the LEDs. Make sure the arrows on the transmitter and Power Reboot Pod are facing each other. 2. Connect the serial connector to the serial port of the ServReach KVM Gate (KVIP1000A). See Figure 3-2. Page blackbox.com

9 Chapter 3: Installation KVIP1000A To serial port Transmitter slotted into a Power Reboot Pod Power Reboot Pods Figure 3-2. Power Reboot Pod transmitter connections. 3. Complete the setup via the ServReach KVM Gate Web configuration interface. See the ServReach KVM Gate (KVIP1000A) user guide to log into the KVM Gate Web interface. The sections below detail the specific areas of the KVM Gate configuration interface that apply to the Power Reboot Pod configuration. Once you log in to the KVM Gate Web interface, from the menu click Serial Settings. The Serial Settings screen appears as shown in Figure 3-3. Figure 3-3. Serial Settings screen. Select Power Reboot Pod from the Assign to drop-down list. All other parameters are then grayed out blackbox.com Page 9

10 Power Reboot Pod User s Manual From the menu, click Switch Configuration, and the screen shown in Figure 3-4 appears. Figure 3-4. Switch Configuration screen. Type a name for the server and type the number of Power Reboot Pods attached to each server as illustrated in Figure 3-4. Save the changes. Remote Session During a remote session, you can power manage the target servers as follows: From the toolbar, click. The power menu appears (see Figure 3-5). Figure 3-5. Power menu. Select the power cycle command, or power up or down the currently accessed target server. NOTE: Only the currently accessed target server is affected, so to power manage other target servers, you must access each one individually. 3.4 Connecting a Power Reboot Pod to the ServReach KVM Cube (KVIP1001A) Connect to the ServReach KVM Cube (KVIP1001A) using the Power Reboot Pod Transmitter as follows. 1. Slide the Transmitter into the slot on the side of the Power Reboot Pod furthest away from the LEDs. Make sure the arrows on the transmitter and Power Reboot Pod are facing each other. 2. Connect the 26-pin connector of the Extender to Power Reboot Pod cable (included with the KVIP1001A) to the 26-pin port of the ServReach KVM Cube. See Figure Connect the ServReach KVM Cube to the Power Reboot Pod cable, connect the Pod s video connector to the server s video port, and connect the Pod s USB connector to the server s USB port. 4. For the rest of the KVM Cube connections, see the ServReach KVM Cube (KVIP1001A) User Guide. Page blackbox.com

11 Chapter 3: Installation LAN/WAN User over IP To transmitter port KVIP1001A to Power Reboot Pod cable To video port To 26-pin port Server To power port To USB port Figure 3-6. Power Reboot Pod to KVIP1001A connections. Remote Session During a remote session, you can power manage the target servers as follows: From the toolbar, click. The power menu appears (see Figure 3-7). Figure 3-7. Power menu blackbox.com Page 11

12 Power Reboot Pod User s Manual 4. Operation 4.1 LED Indicators on the Power Reboot Pod There are two LEDs. The green LED indicates the Power Reboot Pod is connected to a power outlet. The red LED indicates that the server is powered on. Both LEDs flash when the transmitter unit communicates with the serial device. 4.2 Using the Power Reboot Pod Management Utility When Power Reboot Pods are connected to the ServReach KVM Gate or or the ServReach KVM Cube, use the Web interface to configure the Power Reboot Pods. For standalone applications, use the Power Reboot Pod utility or a standard hyperterminal to send commands to the Power Reboot Pods. (The syntax for the commands can be found in Appendix A.) 1. Download the Power Reboot Pod Management Utility program from the Black Box FTP site at ftp.blackbox.com. 2. Install the Power Reboot Pod Management Utility program on your computer. 3. Open it by either clicking the shortcut on the desktop, or choose Start/Programs/Power Reboot Pod Management/Power Reboot Pod Management. The Power Reboot Pod Management Utility appears. 4. Click Commands/Configuration and the General tab appears; see Figure 4-1. You can do the following: Figure 4-1. General tab. Total Power Reboot Pods Change the number of Power Reboot Pods connected from 1 to 99 units. Click Save. The number of Power Reboot Pods selected appears in the Names tab. Auto Numbering This will automatically number all the Power Reboot Pods in the system. Warning! This will erase any names and groups in the system. Click OK. Set ID You can choose to autonumber just some of the Power Reboot Pods and configure the names of other Power Reboot Pods yourself as explained in the Names tab section. Click Set ID. (NOTE: Always have the starting ID set to 1.) Blink ID See which Power Reboot Pod is connected by blinking the LEDs of a defined Power Reboot Pod and specifying the blink time from 1 99 seconds. Page blackbox.com

13 Chapter 4: Operation Delay Time Set the time delay between each Power Reboot Pod in the system shutting down. For example if the delay time is 10 seconds, then there is a delay of 10 seconds between each Power Reboot Pod shutting down when the whole system is shut down. Click Save. Reboot time Choose the time delay from 1 99 seconds for each Power Reboot Pod to reboot, when sending a reboot command to the whole system. Click Save. Names tab Click the Names tab, and Figure 4-2 appears. Give the Power Reboot Pods individual names and click Save. Redundancy tab Figure 4-2. Names tab. When a server has two power outlets, you can connect one Power Reboot Pod to each outlet. You can combine the Power Reboot Pods into a single group so that in the Operation window you see the group of Power Reboot Pods as a unit and not separately. You then power manage the group of Power Reboot Pods and not the individual Power Reboot Pod. For example, if Power Reboot Pods ID 5 and ID 6 are both connected to the Lab server, group Power Reboot Pods ID 5 and ID 6 and call them Lab blackbox.com Page 13

14 Power Reboot Pod User s Manual 1. Click the Redundancy tab, and Figure 4-3 appears. Figure 4-3. Redundancy tab. 2. In the Power Reboot Pods column, select the Power Reboot Pods connected to the same server and click Add. They appear in the right-hand column. 3. Type a name in the Group Name field, or click New to give the group a name. 4. Click Save. The group with the name underneath appears as an icon in the Operation window (see Figure 4-5). Groups tab You can combine different Power Reboot Pods together to form groups which you can then power manage, instead of managing them individually. Page blackbox.com

15 Chapter 4: Operation 1. Click the Groups tab, and the following appears: Figure 4-4. Groups tab. 2. In the PODs column, select the Power Reboot Pods connected to the same server and click Add. They appear in the left-hand column. 3. Type a name in the Group Name field, or click New to give the group a name. 4. Click Save. The group with the name underneath appears as an icon in the Operation window inside the group tab (see Figure 4-5) blackbox.com Page 15

16 Power Reboot Pod User s Manual 4.3 Operating the System To operate the Power Reboot Pods, click on the arrow button or choose Commands/operation. The Operation window appears as shown in Figure 4-5. Figure 4-5. Operation window. 1. Choose to display either the Power Reboot Pods or Groups by pressing the appropriate tab. 2. Click on Power Reboot Pod or Group, and the following screen appears: Figure 4-6. Power management options. 3. Click on the button to power on, power off, or reboot the server or all servers in the group. 4. To power manage all connected Power Reboot Pods, click on the All Power On, All Power Off, or All Reboot button in Figure 4-5. Page blackbox.com

17 Appendix A: RS-232 Control Protocol Appendix A. RS-232 Control Protocol NOTE: Do not use HyperTerminal because it does not support DTR/RTS signals. Switch on ID X basic unit with ID number X will switch on. ^MS005xxx,I M: Fixed Variable S: Switch 005: xxx,i length xxx: ID I: Turn ON Switch off ID X basic unit with ID number X will switch off. ^MS005xxx,O M: Fixed Variable S : Switch 005: xxx,i length xxx: ID O: Turn OFF Reboot ID X Time Y basic unit with ID number X will switch off, and after Y seconds, it will switch on. ^MR007xxx,yyy M: Fixed Variable R: Reboot 007: xxx,yyy length xxx: ID yyy: yyy second Change ID to Y the connected basic unit ID number will be changed to number Y. ^MC007xxx,zzz M: Fixed Variable C: Change ID 007: xxx,zzz length xxx: ID zzz: Change to number zzz blackbox.com Page 17

18 Power Reboot Pod User s Manual System auto number X in case of cascaded basic units, the first one will get ID number X, the next one will get ID number X+1, and so on. ^MA003xxx M: Fixed Variable A: Auto Number 003: xxx length xxx: The first one ID number Polling ID X Time Y basic unit with ID number X will blink red LED about Y seconds. ^MP007xxx,yyy M: Fixed Variable P: Polling 007: xxx,yyy length xxx: ID yyy: yyy second Page blackbox.com

19 Appendix B: Serial Port Pinout Appendix B. Serial Port Pinout The pinning for the interconnect cable is shown in Figure B-1. Table B-1. Interconnect cable pinning. POD Transmitter DB9 Connector not used 1 not used 2 Green (RX) 3 Yellow (DTR) 4 not used 5 not used 6 Blue (RTS) 7 not used 8 Red (RI) blackbox.com Page 19

20 Black Box Tech Support: FREE! Live. 24/7. Tech support the way it should be. Great tech support is just 30 seconds away at or blackbox.com. About Black Box Black Box Network Services is your source for more than 118,000 networking and infrastructure products. You ll find everything from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by free, live 24/7 Tech support available in 30 seconds or less. Copyright All rights reserved. PRP1000A user guide, version blackbox.com