1 Introduction - Advice Conductor Rails Track Coupler Power feeds Air Gap Insulation Section... 6

Transcription

1 Contents 1 Introduction - Advice Conductor Rails Track Coupler Power feeds Air Gap Insulation Section Expansion joints Anchor Caps End Caps (Distance between Phases 14 mm) Hanger Clamps Current Collectors translated document Page 1 of 14

2 1 Introduction - Advice The conductor rail 0815 PE with polarity protection PE plus features a larger contact width for the current collector head than the standard conductor rails Due to this special feature the grounding collector (PE) current collector head cannot intervene in a phase (PH) conductor rail. This solution will safely prevent accidental energizing of the phase voltage to the PE pole and the improper utilization of the PE current collector as phase current collector! This technical data sheet describes all necessary standard components for the construction of a conductor rail of program 0815 SingleFlexLine with PE plus - polarity protection for the installation in monorail systems (EMS) and similar applications. It serves as a supplement to the existing catalogs. The PE rail system of existing conductor rail systems SingleFlexLine 0815 can be refitted. All that needs to be replaced are the existing PE rails, end caps and the PE current collectors. The hanger clamps and the PH rails must not be replaced. The existing current collectors can be operated in the new PE rail, so that a gradual reconstruction of the existing current collectors can be realized. A polarity protection device should generally be provided on new installations or modernizations of EMS! translated document Page 2 of 14

3 2 Conductor Rails PH PE PE plus (PE with polarity protection) Conductor rail for curve manufacturing Type Order Number Copper rail 100 A for collector PH, 4000 mm x Copper rail 100 A for grounding collector PE; without polarity protection PE plus 4000 mm Copper rail 100 A for grounding collector PE plus ; with polarity protection PE plus 4000 mm x x Copper rail 100 A for collector PH; 6000 mm x Copper rail 100 A for grounding collector PE; without polarity protection PE plus 6000 mm Copper rail 100 A for grounding collector PE plus ; with polarity protection PE plus 6000 mm Copper rail 100 A for grounding collector PE plus ; with polarity protection 4000 mm, for manufacturing of curves with radius < mm x x x15 1,092 The grounding collector insulations are marked yellow-green on both sides. All technical details are according to the standard conductor rail For manufacturing of curves with small radius use special rail x15! Rails and other components and cable cores with PE identification (yellow-green) may not be used as live components. The PE plus rail with polarity protection has an additional fixation of the insulating profile (T-profile at the insulation profile base). translated document Page 3 of 14

4 3 Track Coupler Type Order Number Track coupler, screwable Color: Black/Usable for all rail links translated document Page 4 of 14

5 4 Power feeds Type Order Number Power feed mm²; with crimp type cable lug Power feed 4-6 mm²; with crimp type cable lug Power feed 5-10 mm²; with crimp type cable lug Color: Black/usable for all types of rails/cable outer diameter: max. Ø 6 mm translated document Page 5 of 14

6 5 Air Gap Insulation Section The air gap insulation sections with polarity protection differ from the component without polarity protection by the adaptation of the end caps. The end caps for the grounding connector (green) have a larger contact dimension for the wide PE plus collector shoe. The phase caps have additional carbon guidance in the lateral part of the caps. Type Component Order Number Air gap insulation section PH without feed Air gap insulation section PH with feed mm² PH Air gap insulation section PH with feed 4-6 mm² Air gap insulation section PE plus without feed Air gap insulation section PE plus with feed mm² PE Air gap insulation section PE plus with feed 4-6 mm² translated document Page 6 of 14

7 6 Expansion joints Expansion joint, 8 mm expansion distance Expansion joint, 20 mm expansion distance Type Number of poles Expansion distance [mm] Order Number Expansion joint PE plus with polarity protection Expansion joint PH Expansion joint PE plus with polarity protection Expansion joint PH Expansion joint combinations for multi-pole systems. The set includes all components for a multi-pole expansion point. Mounting position of the PE poles can be chosen freely. Type Number of poles Expansion distance [mm] Order Number Expansion joint set with PE plus 4 poles 8 mm Expansion joint set with PE plus 6 poles 8 mm Expansion joint set with PE plus 8 poles 8 mm Expansion joint set with PE plus 4 poles 20 mm Expansion joint set with PE plus 6 poles 20 mm Expansion joint set with PE plus 8 poles 20 mm Color: All PE components with PE plus cap components green, all other components black. translated document Page 7 of 14

8 7 Anchor Caps The Anchor Caps are installed to the left and right of a hanger clamp and can be used for all types of rails. Type Order Number Anchor point cap translated document Page 8 of 14

9 8 End Caps (Distance between Phases 14 mm) Type Number of Poles Power Feed Order Number End cap set complete with PE plus x14x End cap set complete with PE plus x14x End cap set complete with PE plus mm² x14x End cap set complete with PE plus mm² x14x End cap set complete with PE plus mm² x14x End cap set complete with PE plus mm² x14x End cap PH; individual with PH 1-08-E End cap PH; individual with PH mm² 08-E End cap PH; individual with PH mm² 08-E translated document Page 9 of 14

10 Type Number of Poles Power Feed Order Number End cap PE; individual with PE plus x14x End cap PE; individual with PE plus mm² x14x End cap PE; individual with PE plus mm² x14x Color: All PE components with PE plus green. translated document Page 10 of 14

11 9 Hanger Clamps No matter which type of rail, all standard and EMS or customer-specific screwed and quick assembly hanger clamps of the SingleFlexLine program 0815 can be used. Illustr.: Example for system-dependent hanger clamps with Leuze positioning bar code band and leaky coax cable. See also standard program or contact our system consultant. A great number von brackets is available, aligned to the respective EMS-profile, and the respective system brackets can be manufactured. translated document Page 11 of 14

12 10 Current Collectors The PE current collectors with polarity protection PE plus differ from the standard current collector by a wider carbon shoe and a codification lug at the snap-in fixation. A notch is provided here at the PE installation position of the counterpart, the mounting plate. In case of a retrofit exchange the mounting plate or apply a notch. Due to the high number of available current collectors we have only listed the double current collectors basic types for the EMSarea here, without customer-specific special configurations. In case of need please contact us or consider the particularities based on the bidding specifications of the quotation. The PE plus current collector head cannot intervene in a PH conductor rail! The following Illustr. shows the double current collector 0815 with snap-in assembly and mounting plate (position PE coded). - Double current collector with copper graphite carbon 2 x 25 A - without connecting cable - Carbon length 50 mm - with AMP plug and socket connection - Height of carbon standard - snap-in type - Phase distance 14 mm - with PE plus polarity protection - Mounting distance base plate conductor rail bottom 80 mm (with cable guidance and cable package + 15 mm) Mounting position of the compensation spring for towing mode (for mainly towing mode). translated document Page 12 of 14

13 Type Number of poles Order Number Current collector P 2 x 25 A; PE plus REW Current collector P 2 x 25 A; PE plus TOW Current collector* complete PE plus 2 x 25 A Current collector* complete PE plus 2 x 25 A Current collector mounting plate 1-8 See advice * Current collector head complete: carbon, insulation ** TOW = Towing Mode /REV = Reverse Mode Advice: System bracket and current collector types as well as special types. The high variance of parameters and various requirements of final customers (automotive industry and system manufacturers) as well as variously applied techniques (construction principle, installation space, etc.), offer a great number of possible combinations and special constructions, which cannot all be listed in this survey. Please contact our consulting service. We will be pleased to assist you. translated document Page 13 of 14

14 Conductix-Wampfler GmbH Rheinstrasse D Weil am Rhein - Maerkt Germany Phone: +49 (0) Fax: +49 (0) info.de@conductix.com translated document Page 14 of 14