WAGO-I/O-SYSTEM 750 KNX/EIB/TP1 Module Device Mode. Manual. Version 1.1.0

Transcription

1 Pos : 3 /Alle Serien (Allgemeine M odul e)/hinweise z ur Dokumentation/Impres sum für Standardhandbüc her - allg. Angaben, Ansc hriften, Tel efonnummer n und -Adres @ 1 Pos: 2 /Dokumentation allgemein/einband/einband Handbuch - Dec kbl att ohne Variantenfel d (Standar @ 1 WAGO-I/O-SYSTEM 750 KNX/EIB/TP1 Module Device Mode

2 === Ende der Liste für T extmar ke Ei nband_vorne === 2 WAGO-I/O-SYSTEM by WAGO Kontakttechnik GmbH & Co. KG All rights reserved. WAGO Kontakttechnik GmbH & Co. KG Hansastraße 27 D Minden Phone: +49 (0) 571/ Fax: +49 (0) 571/ Web: info@wago.com Technical Support Phone: +49 (0) 571/ Fax: +49 (0) 571/ support@wago.com Every conceivable measure has been taken to ensure the accuracy and completeness of this documentation. However, as errors can never be fully excluded, we always appreciate any information or suggestions for improving the documentation. documentation@wago.com We wish to point out that the software and hardware terms as well as the trademarks of companies used and/or mentioned in the present manual are generally protected by trademark or patent.

3 WAGO-I/O-SYSTEM 750 Table of Contents 3 Pos : 5 /D okumentati on allgemein/verzeic hnisse/inhalts verz eichnis - Ü berschrift og und Verzei @ 1 Table of Contents 1 Notes about this Documentation Validity of this Documentation Copyright Symbols Number Notation Font Conventions Important Notes Legal Bases Subject to Changes Personnel Qualifications Use of the 750 Series in Compliance with Underlying Provisions Technical Condition of Specified Devices Safety Advice (Precautions) Device Description View Connectors Display Elements Operating Elements Schematic Diagram Technical Data Device Data Supply KNX Communication Climatic Environmental Conditions Approvals Standards and Guidelines Function Description Application of Module with PFC Interworking Datapoint Types Data Exchange between KNX/EIB/TP1 Module and IEC Application Startup Behavior of the KNX/EIB/TP1 Module in Device Mode Installation Notes Process Image Mounting Mounting Sequence Inserting and Removing Devices Inserting I/O Module Removing the I/O Module I/O Modules with Pluggable Wiring Level (Series 753) Coding Connector Removal... 37

4 === Ende der Liste für T extmar ke Verzeic hnis_vor ne === 4 Table of Contents WAGO-I/O-SYSTEM Use in Hazardous Environments Marking Configuration Examples Marking for Europe according to ATEX and IEC-Ex Marking for America according to NEC Installation Regulations Special conditions for safe use (ATEX Certificate TÜV 07 ATEX X) Special conditions for safe use (ATEX Certificate TÜV 12 ATEX X)... 47

5 Pos : 8 /Alle Serien (Allgemeine M odul e)/hinweise z ur Dokumentation/Hi nweis e/hi nweis : D okumentation aufbewahr @ 1 Pos: 12.2 /Dokumentation allgemei n/glieder ungs elemente/---seitenwechs @ 1 WAGO-I/O-SYSTEM 750 Notes about this Documentation 5 Pos : 7 /Alle Serien (Allgemeine M odul e)/übersc hriften für all e Serien/Hi nweis z ur Dokumentation/Hinweis e z ur D okumentation - Ü bersc hrift Notes about this Documentation Keep this documentation! The operating instructions are part of the product and shall be kept for the entire lifetime of the device. They shall be transferred to each subsequent owner or user of the device. Care must also be taken to ensure that any supplement to these instructions are included, if applicable. Pos : 9 /Alle Serien (Allgemeine M odul e)/übersc hriften für all e Serien/Hi nweis z ur Dokumentation/Gültig keits ber eich - Übersc hrift Validity of this Documentation Pos : 10 /Serie 750 ( WAGO-I/O-SYST EM)/Hi nweis e z ur D okumentati on/gültigkeits bereic h/gültig keits ber eich Dokumentation Bus kl emme 750- xxxx, ohne @ 1 This documentation is only applicable to the I/O module (KNX/EIB/TP1 Module). Pos : 11 /Serie 750 ( WAGO-I/O-SYST EM)/Hi nweis e z ur D okumentati on/hi nweise/ac htung: Hinweis z ur D okumentati on Bus kl emmen @ 1 The I/O module shall only be installed and operated according to the instructions in this manual and in the manual for the used fieldbus coupler/controller. Consider power layout of the WAGO-I/O-SYSTEM 750! In addition to these operating instructions, you will also need the manual for the used fieldbus coupler/controller, which can be downloaded at There, you can obtain important information including information on electrical isolation, system power and supply specifications. Pos : 12.1 /All e Seri en ( Allgemei ne Module)/Hi nweis e zur D okumentati on/urhebersc hutz Copyright This, including all figures and illustrations, is copyright-protected. Any further use of this by third parties that violate pertinent copyright provisions is prohibited. Reproduction, translation, electronic and phototechnical filing/archiving (e.g., photocopying) as well as any amendments require the written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany. Non-observance will involve the right to assert damage claims.

6 Pos : /All e Serien ( Allgemei ne Module)/Wic htige Erläuterungen/Sicherheits- und sonstige Hinweise/Gefahr/Gefahr: _Warnung vor Personenschäden allgemein_ - Erl äuter @ 1 Pos : /All e Serien ( Allgemei ne Module)/Wic htige Erläuterungen/Sicherheits- und sons tige Hinweis e/gefahr/gefahr: _War nung vor Personenschäden durc h elektrisc hen Strom_ - @ 1 Pos : /All e Serien ( Allgemei ne Module)/Wic htige Erläuterungen/Sicherheits- und sons tige Hinweis e/warnung/warnung: _Warnung vor Personensc häden allgemei n_ - @ 1 Pos : /All e Serien ( Allgemei ne Module)/Wic htige Erläuterungen/Sicherheits- und sons tige Hinweis e/vorsic ht/vorsicht: _War nung vor Pers onensc häden allgemein_ - @ 1 Pos : /All e Serien ( Allgemei ne Module)/Wic htige Erläuterungen/Sicherheits- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sachschäden allgemein_ - @ 1 Pos : /All e Serien ( Allgemei ne Module)/Wic htige Erläuterungen/Sicherheits- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sachschäden durch elektrostatische Aufladung_ - @ 1 Pos : /All e Serien ( Allgemei ne Module)/Wic htige Erläuterungen/Sicherheits- und sonstige Hinweise/Hi nweis/hinweis: _Wichtiger Hi nweis allgemein_ - @ 1 Pos : /All e Serien ( Allgemei ne Module)/Wic htige Erläuterungen/Sicherheits- und sons tige Hinweis e/infor mation/infor mation: _Weiter e Infor mation allgemei n_ - Erl äuter @ 1 6 Notes about this Documentation WAGO-I/O-SYSTEM 750 Pos : 12.3 /All e Seri en ( Allgemei ne Module)/Ü bers chriften für alle Serien/Hinweis z ur D okumentati on/symbole - Ü berschrift Symbols Personal Injury! Indicates a high-risk, imminently hazardous situation which, if not avoided, will result in death or serious injury. Personal Injury Caused by Electric Current! Indicates a high-risk, imminently hazardous situation which, if not avoided, will result in death or serious injury. Personal Injury! Indicates a moderate-risk, potentially hazardous situation which, if not avoided, could result in death or serious injury. Personal Injury! Indicates a low-risk, potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Damage to Property! Indicates a potentially hazardous situation which, if not avoided, may result in damage to property. Damage to Property Caused by Electrostatic Discharge (ESD)! Indicates a potentially hazardous situation which, if not avoided, may result in damage to property. Important Note! Indicates a potential malfunction which, if not avoided, however, will not result in damage to property.

7 Pos: 12.5 /Dokumentation allgemein/gliederungselemente/---seitenwechs @ 1 WAGO-I/O-SYSTEM 750 Notes about this Documentation 7 Additional Information: Refers to additional information which is not an integral part of this documentation (e.g., the Internet).

8 Pos : 13 /D okumentation allgemei n/glieder ungs elemente/---seitenwechs @ 1 8 Notes about this Documentation WAGO-I/O-SYSTEM 750 Pos : 12.6 /All e Seri en ( Allgemei ne Module)/Hi nweis e zur D okumentati on/zahlens Number Notation Table 1: Number notation Number code Example Note Decimal 100 Normal notation Hexadecimal 0x64 C notation Binary '100' ' ' In quotation marks, nibble separated with dots (.) Pos : 12.7 /All e Seri en ( Allgemei ne Module)/Hi nweis e zur D okumentati on/sc hriftkonventi Font Conventions Table 2: Font conventions Font type Indicates italic Names of paths and data files are marked in italic-type. e.g.: C:\Programme\WAGO-I/O-CHECK Menu Menu items are marked in bold letters. e.g.: Save > A greater-than sign between two names means the selection of a menu item from a menu. e.g.: File > New Input Designation of input or optional fields are marked in bold letters, e.g.: Start of measurement range Value Input or selective values are marked in inverted commas. e.g.: Enter the value 4 ma under Start of measurement range. [Button] Pushbuttons in dialog boxes are marked with bold letters in square brackets. e.g.: [Input] [Key] Keys are marked with bold letters in square brackets. e.g.: [F5]

9 WAGO-I/O-SYSTEM 750 Important Notes 9 Pos : 14 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Wichtige Erläuterungen/Wichtige Erläuterungen - Übersc hrift Important Notes Pos : 15.1 /All e Seri en ( Allgemei ne Dokumente) ( Allgemei ne Module)/Wic htige Erläuterungen/Einl eitung Wic htige @ 1 This section includes an overall summary of the most important safety requirements and notes that are mentioned in each individual section. To protect your health and prevent damage to devices as well, it is imperative to read and carefully follow the safety guidelines. Pos : 15.2 /All e Seri en ( Allgemei ne Module)/Ü bers chriften für alle Serien/Wichtige Erläuter ungenr ec htlic he Gr undlag en - Übersc hrift Legal Bases Pos: 15.3 /Alle Serien (Allgemeine Dokumente) (Allgemeine Module)/Wichtige Erläuterungen/Änderungsvorbehalt - Ü bers chrift 3 und Subject to Changes WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any alterations or modifications that serve to increase the efficiency of technical progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from the granting of patents or from the legal protection of utility patents. Third-party products are always mentioned without any reference to patent rights. Thus, the existence of such rights cannot be excluded. Pos: 15.4 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Pers onalqualifi kationpers onalqualifi kation 750- xxxx - Ü bersc hrift 3 und Personnel Qualifications All sequences implemented on Series 750 devices may only be carried out by electrical specialists with sufficient knowledge in automation. The specialists must be familiar with the current norms and guidelines for the devices and automated environments. All changes to the coupler or controller should always be carried out by qualified personnel with sufficient skills in PLC programming. Pos : 15.5 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Bestimmungsgemäße VerwendungBestimmungsgemäße Verwendung 750-xxxx - Ü berschrift 3 und Inhal Use of the 750 Series in Compliance with Underlying Provisions Couplers, controllers and I/O modules found in the modular WAGO-I/O- SYSTEM 750 receive digital and analog signals from sensors and transmit them to the actuators or higher-level control systems. Using programmable controllers, the signals can also be (pre-) processed. The components have been developed for use in an environment that meets the IP20 protection class criteria. Protection against finger injury and solid impurities up to 12.5 mm diameter is assured; protection against water damage is not ensured. Unless otherwise specified, operation of the components in wet and dusty environments is prohibited. Operating 750 Series components in home applications without further measures is only permitted if they meet the emission limits (emissions of interference) according to EN You will find the relevant information in the section on WAGO-I/O-SYSTEM 750 System Description Technical Data in the manual for the used fieldbus coupler/controller.

10 Pos: 15.7 /Dokumentation allgemein/gliederungselemente/---seitenwechs @ 1 10 Important Notes WAGO-I/O-SYSTEM 750 Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O- SYSTEM 750 in hazardous environments. Please note that a prototype test certificate must be obtained that confirms the correct installation of the system in a housing or switch cabinet. Pos : 15.6 /All e Seri en ( Allgemei ne Dokumente) ( Allgemei ne Module)/Wic htige Erläuterungen/T ec hnis cher Z ustand der Geräte - Übersc hrift 3 und Technical Condition of Specified Devices The devices to be supplied ex works are equipped with hardware and software configurations, which meet the individual application requirements. WAGO Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of changes in hardware or software as well as to non-compliant usage of devices. Please send your request for modified and new hardware or software configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

11 Pos : /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/wichtige Erläuter ungen/sic herheits hinweise/gefahr /Gefahr: Nicht an Geräten unter Spannung ar @ 1 Pos : /Serie 750 ( WAGO-I/O- SYST EM)/Wic htig e Erl äuter ung en/sic her hei ts- und s onstige Hi nweise/gefahr/gefahr: Ei nbau xxxx nur i n Gehäus en, Sc hränken oder el ektrisc hen @ 1 Pos : /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/wichtige Erläuter ungen/sic herheits hinweise/gefahr /Gefahr: Unfall verhütungsvorsc hriften @ 1 Pos : /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/wichtige Erläuter ungen/sic herheits hinweise/gefahr /Gefahr: Auf normg erec hten Ansc hluss ac @ 1 Pos: /Alle Serien (Allgemeine Dokumente) (Allgemeine Module)/Wichtige Erläuterungen/Sic herheits hinweise/achtung/ac htung: Nic ht i n T elekommuni kati ons netz en ei ns etz en! (Z usatz RJ- @ 1 Pos : /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/wichtige Erläuter ungen/sic herheits hinweise/ac htung/ac htung: Defekte oder besc hädigte Ger äte aus tausc @ 1 Pos : /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/wichtige Erläuter ungen/sic herheits hinweise/ac htung/ac htung: Geräte vor kriec henden und is olier enden Stoffen @ 1 Pos : /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/wichtige Erläuter ungen/sic herheits hinweise/ac htung/ac htung: Rei nigung nur mit zul ässigen M @ 1 WAGO-I/O-SYSTEM 750 Important Notes 11 Pos : 15.8 /All e Seri en ( Allgemei ne Module)/Ü bers chriften für alle Serien/Wichtige Erläuter ungensic her hei tshi nweis e - Übersc hrift Safety Advice (Precautions) Pos : 15.9 /All e Seri en ( Allgemei ne Dokumente) ( Allgemei ne Module)/Wic htige Erläuterungen/Sicherheits hi nweis e/einl eitung Sicherheits hinweis e H @ 1 For installing and operating purposes of the relevant device to your system the following safety precautions shall be observed: Do not work on components while energized! All power sources to the device shall be switched off prior to performing any installation, repair or maintenance work. Installation only in appropriate housings, cabinets or in electrical operation rooms! The WAGO-I/O-SYSTEM 750 and its components are an open system. As such, install the system and its components exclusively in appropriate housings, cabinets or in electrical operation rooms. Allow access to such equipment and fixtures to authorized, qualified staff only by means of specific keys or tools. Not for use in telecommunication circuits! Only use devices equipped with ETHERNET or RJ-45 connectors in LANs. Never connect these devices with telecommunication networks. Replace defective or damaged devices! Replace defective or damaged device/module (e.g., in the event of deformed contacts), since the long-term functionality of device/module involved can no longer be ensured. Protect the components against materials having seeping and insulating properties! The components are not resistant to materials having seeping and insulating properties such as: aerosols, silicones and triglycerides (found in some hand creams). If you cannot exclude that such materials will appear in the component environment, then install the components in an enclosure being resistant to the above-mentioned materials. Clean tools and materials are imperative for handling devices/modules.

12 Pos : /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/wichtige Erläuter ungen/sic herheits hinweise/ac htung/ac htung: Kei n Kontakts pray @ 1 Pos : /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/wichtige Erläuter ungen/sic herheits hinweise/ac htung/ac htung: Verpol ung ver mei @ 1 Pos : /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/wichtige Erläuter ungen/sic herheits hinweise/ac htung/ac htung: El ektr ostatisc he Entl adung @ 1 Pos : 16 /D okumentation allgemei n/glieder ungs elemente/---seitenwechs @ 1 12 Important Notes WAGO-I/O-SYSTEM 750 Cleaning only with permitted materials! Clean soiled contacts using oil-free compressed air or with ethyl alcohol and leather cloths. Do not use any contact spray! Do not use any contact spray. The spray may impair contact area functionality in connection with contamination. Do not reverse the polarity of connection lines! Avoid reverse polarity of data and power supply lines, as this may damage the devices involved. Avoid electrostatic discharge! The devices are equipped with electronic components that you may destroy by electrostatic discharge when you touch. Pay attention while handling the devices to good grounding of the environment (persons, job and packing).

13 WAGO-I/O-SYSTEM 750 Device Description 13 Pos : 17 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Gerätebesc hreibung/gerätebeschr eibung - Übersc hrift 3\mod_ _21.doc 1 3 Device Description Pos : 18 /Serie 753 ( WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/ei nlei tung/bus kl emmenbes chr eibung Ger @ 1 The KNX/EIB/TP1 module , a.k.a. KNX module, provides the integration of two-wire TP1 networks or individual KNX devices into all relevant WAGO building automation controllers. The KNX module can be operated in the operating modes Device mode or Router mode. In a KNX IP controller, the module can assume either the device or router mode. When using a different WAGO controller, the module will operate in device mode only. If one or more KNX modules are operated in a KNX IP controller, it behaves as a normal KNX device (device mode) within the TP1 network. This is also the case when used with a different WAGO controller. The position, upstream or downstream, of the KNX module is irrelevant. The controller and the module are coupled via the internal data bus. The module also features four termination points for the connection of the KNX bus line (two KNX + in red and two KNX in dark gray). As per EIBA/KNX Association, a standard MSR conductor (e.g., PYCYM ) or a telecommunications cable (e.g., J-Y(St)Y ) is recommended for the KNX bus line (red and black wires). The bus line is installed in free topology (ring topologies may not be created). In addition, the conductor length of the bus line is limited, and maximum conductor lengths between bus devices may not be exceeded, therefore, general KNX directives must be adhered to. The I/O module has two programming buttons for parameterization in device mode. The engineering tool software (ETS) requests the actuation during activation of the KNX module. And, together with the WAGO-specific ETS Plug-in, this software is used for the activation and configuration of KNX devices. Eight colored LED's on the modules enclosure signal active and inactive operating modes, the data transfer via KNX and the module bus, the presence of a KNX bus voltage, and internal states or fault conditions of the module (see chapter Display Elements ).

14 Pos : 19 /D okumentation allgemei n/glieder ungs elemente/---seitenwechs @ 1 14 Device Description WAGO-I/O-SYSTEM 750 Note the compatibility with couplers/controllers! Not all controllers are supported by the KNX/EIB/TP1 module at the moment (update 03/2014). The KNX module does not work with the following controllers: INTERBUS controller ( ) DeviceNet controller ( ) MODBUS controller ( , -814, -815, -816) The utilization of the module on couplers is excluded. Additional Information Detailed notes to the WAGO ETS Plug-in and the Plug-in itself can be found on the website

15 Pos : 21 /Serie 753 ( WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/ansic ht/sonder klemmen/ansic ht @ 1 d Pos : 22 /D okumentation allgemei n/glieder ungs elemente/---seitenwechs @ 1 WAGO-I/O-SYSTEM 750 Device Description 15 Pos : 20 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Gerätebesc hreibung/ansic ht - Ü berschrift View Figure 1: View Table 3: Legend for View figure No Description Meaning For details see Section Marking options using the Mini-WSB A...H Status LEDs Device Description > Display Elements Data contacts Mounting > Connect Devices 4 1, 5 Not connected , 6 Programming button Device Description > Operating Elements 6 3, 7 + KNX bus Device Description > Connectors Attention: Plug internally bridged , 8 - KNX bus Device Description > Connectors

16 Pos : 24 /Serie 753 ( WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/ansc hl üsse/sonderklemmen/anschlüsse @ 1 Pos : 25 /D okumentation allgemei n/glieder ungs elemente/---seitenwechs @ 1 16 Device Description WAGO-I/O-SYSTEM 750 Pos : 23 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Gerätebesc hreibung/ansc hlüsse - Übersc hrift Connectors Table 4: Connectors Connector Channel Function Not connected Programming button 3 * + KNX bus 4 * - KNX bus Not connected Programming button Figure 2: Connectors 7 * + KNX bus 8 * - KNX bus * The KNX module has an internal bridge between the KNX+ and KNX- connections.

17 Pos : 27 /Serie 753 ( WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/anz eigeelemente/sonder klemmen/anz eigeel emente @ 1 Pos : 28 /D okumentation allgemei n/glieder ungs elemente/---seitenwechs @ 1 WAGO-I/O-SYSTEM 750 Device Description 17 Pos : 26 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Gerätebesc hreibung/anz eigeel emente - Übersc hrift Display Elements Table 5: Display elements LED Name State Function off Operating mode Router not active A Router mode on Operating mode Router active green flashing Synchronization KNX off KNX programming mode not active B programming on KNX programming mode active red mode flashing Checksum error C Data transfer off Internal data bus data transfer not active green internal bus flashing Internal data bus data transfer active D Data transfer off KNX data transfer not active yellow KNX flashing KNX data transfer active off Device mode not active Figure 3: E Device mode on Device mode active Display elements green flashing Synchronization F Buffer off No buffer overflow red overflow on Overflow G off No fault Internal fault red on Checksum error / device not configured H KNX bus off KNX bus voltage not available green voltage on KNX bus voltage available

18 Pos : 31 /D okumentation allgemei n/glieder ungs elemente/---seitenwechs @ 1 18 Device Description WAGO-I/O-SYSTEM 750 Pos : 29 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Gerätebesc hreibung/bedienel emente - Ü berschrift Operating Elements Pos : 30 /Serie 753 ( WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/bedienel emente/bus klemmen/bedienelemente @ 1 The I/O module has two programming button connections (see figure below) for parameterization of the KNX module in the device mode. Figure 4: Programming button Actuation of the buttons is requested by the engineering tool software (ETS) during startup of the module. A temporary electrical connection is established between these two programming button connectors (2 and 6), via a wire jumper for example, which activates the programming mode.

19 Pos : 33 /Serie 753 ( WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/schematisc hes Sc haltbild/sc hematisc hes Schaltbild @ 1 Pos: 34 /Dokumentation allgemei n/glieder ungs elemente/---seitenwechs @ 1 WAGO-I/O-SYSTEM 750 Device Description 19 Pos : 32 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Gerätebesc hreibung/sc hematisches Sc haltbil d - Ü bersc hrift Schematic Diagram Figure 5: Schematic Diagram

20 Pos : 38 /Serie 750 ( WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/t echnisc he Daten/Kli matische U mweltbeding ung en/technisc he Daten Klimatisc he U mweltbedingungen m. erw. T empbereic h; C / C / Device Description WAGO-I/O-SYSTEM 750 Pos : 35 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Gerätebesc hreibung/technisc he Daten - Ü berschrift Technical Data Pos : 36 /Serie 753 ( WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/t echnisc he Daten/T ec hnische D aten Device Data Table 6: Technical data Device data Width Weight 12 mm approx. 55 g (incl. connector) Supply Table 7: Technical data Supply Voltage supply (KNX) Current consumption (KNX) Voltage supply (internal) Current consumption (internal) Isolation via KNX power supply unit 5 ma via system voltage DC/DC max. 25 ma 2,5 kv rms Pos : 37 /Serie 753 ( WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/t echnisc he Daten/T ec hnische D aten KNX Communication Table 8: Technical data KNX KNX specification 1.0 Internal data width 24 byte, of which 14 byte for KNX data Data transmission rate (KNX) 9,6 KBaud Programming with WAGO-I/O-PRO Commissioning (KNX side) with ETS Plug-in; programming button bridge 2/6 Diagnostic information via FbKNX_Master_646 function block Fault behavior via FbKNX_Master_646 function block Device mode Number of communication objects 253 Number of group addresses/ 254 associations

21 Pos : 39 /D okumentation allgemei n/glieder ungs elemente/---seitenwechs @ 1 WAGO-I/O-SYSTEM 750 Device Description Climatic Environmental Conditions Table 9: Technical Data Climatic environmental conditions Operating temperature range 0 C 55 C Operating temperature range for -20 C +60 C components with extended temperature range (750-xxx/025-xxx) Storage temperature range -25 C +85 C Storage temperature range for -40 C +85 C components with extended temperature range (750-xxx/025-xxx) Relative humidity max. 5 % 95 % without condensation Resistance to harmful substances Acc. to IEC and IEC Maximum pollutant concentration at SO 2 25 ppm relative humidity <75 % H 2 S 10 ppm Special conditions Ensure that additional measures for components are taken, which are used in an environment involving: dust, caustic vapors or gases ionizing radiation

22 Pos : 42.1 /All e Seri en ( Allgemei ne Dokumente) ( Allgemei ne Module)/Z ulassungen/standardz ulassungen/c E (Konformi täts kennz @ 1 Pos : 42.2 /All e Seri en ( Allgemei ne Dokumente) ( Allgemei ne Module)/Z ulassungen/standardz ulassungen/cu Lus (U @ 1 Pos: 42.3 /Dokumentation allgemein/gliederungselemente/------leerz @ 1 Pos : 43 /All e Seri en (Allgemei ne Module)/Zulassungen/Standardzulassungen/KNX-z ertifizi @ 1 Pos : 44 /D okumentation allgemei n/glieder ungs elemente/------leerz @ 1 Pos : 46.1 /All e Seri en ( Allgemei ne Module)/Z ulassungen/ex-zul ass ungen/tüv AT EX/TÜ V 07 AT EX X: I M 2 Ex d I M b II 3 G Ex na IIC T 4 Gc II 3 D Ex tc IIIC T135 C @ 1 Pos : 46.2 /All e Seri en ( Allgemei ne Module)/Z ulassungen/ex-zul ass ungen/ergänz ung Z ul ässiger U mgebungstemper aturbereic h 0 C <= Ta <= +60 @ 1 Pos : 46.3 /All e Seri en ( Allgemei ne Module)/Z ulassungen/ex-zul ass ungen/iecex (TÜV N or d)/iecex TUN X: Ex d I M b Ex na IIC T4 Gc Ex tc IIIC T 135 @ 1 Pos : 46.4 /All e Seri en ( Allgemei ne Module)/Z ulassungen/ex-zul ass ungen/ergänz ung Z ul ässiger U mgebungstemper aturbereic h 0 C <= Ta <= +60 @ 1 Pos: 46.5 /Dokumentation allgemein/gliederungselemente/------leerz @ 1 Pos : 48.1 /All e Seri en ( Allgemei ne Dokumente) ( Allgemei ne Module)/Z ulassungen/sc hiffsz ul ass ungen/abs ( Americ an Bureau of Shi ppi @ 1 Pos : 48.2 /All e Seri en ( Allgemei ne Dokumente) ( Allgemei ne Module)/Z ulassungen/sc hiffsz ul ass ungen/bv (Bureau @ 1 Pos : 48.3 /All e Seri en ( Allgemei ne Dokumente) ( Allgemei ne Module)/Z ulassungen/sc hiffsz ul ass ungen/dn V (D et N ors ke Veritas) Cl ass @ 1 Pos : 48.4 /All e Seri en ( Allgemei ne Dokumente) ( Allgemei ne Module)/Z ulassungen/sc hiffsz ul ass ungen/gl (Germanisc her Lloyd) C at. A, B, C, D ( EMC @ 1 Pos : 48.5 /All e Seri en ( Allgemei ne Dokumente) ( Allgemei ne Module)/Z ulassungen/sc hiffsz ul ass ungen/kr ( Kor ean R egister of Shi ppi @ 1 Pos : 48.6 /All e Seri en ( Allgemei ne Dokumente) ( Allgemei ne Module)/Z ulassungen/sc hiffsz ul ass ungen/lr ( Lloyd s R egister) Env. 1, 2, 3, @ 1 Pos : 48.7 /All e Seri en ( Allgemei ne Dokumente) ( Allgemei ne Module)/Z ulassungen/sc hiffsz ul ass ungen/n KK (Nippon Kaiji @ 1 Pos : 48.8 /All e Seri en ( Allgemei ne Dokumente) ( Allgemei ne Module)/Z ulassungen/sc hiffsz ul ass ungen/pr S (Pols ki R ejes tr @ 1 22 Device Description WAGO-I/O-SYSTEM 750 Pos : 40 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Gerätebesc hreibung/zul ass ungen - Übersc hrift Approvals Pos : 41 /Serie 750 ( WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/z ulass ungen/allgemei n/z ulass ungen Bus kl emme 750- xxxx Allgemein, ohne Variantenang abe - Einl @ 1 The following approvals have been granted to I/O modules: Conformity Marking CUL US UL508 KNX certified Pos : 45 /Serie 750 ( WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/z ulass ungen/ex/z ulas sungen Bus kl emme 750- xxxx Ex, ohne Variantenangabe - Ei @ 1 The following Ex approvals have been granted to I/O modules: TÜV 07 ATEX X I M2 Ex d I Mb II 3 G Ex na IIC T4 Gc II 3 D Ex tc IIIC T135 C Dc Ambient temperature range: 0 C T a +60 C IECEx TUN X Ex d I Mb Ex na IIC T4 Gc Ex tc IIIC T135 C Dc Ambient temperature range: 0 C T a +60 C Pos : 47 /Serie 750 ( WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/z ulass ungen/schiff/z ulas sungen Bus klemme 750- xxxx Sc hiff, ohne Variantenangabe - Ei nlei @ 1 The following ship approvals have been granted to I/O modules: ABS (American Bureau of Shipping) BV (Bureau Veritas) DNV (Det Norske Veritas) Class B GL (Germanischer Lloyd) Cat. A, B, C, D (EMC 1) KR (Korean Register of Shipping) LR (Lloyd s Register) Env. 1, 2, 3, 4 NKK (Nippon Kaiji Kyokai)

23 Pos : 48.9 /All e Seri en ( Allgemei ne Dokumente) ( Allgemei ne Module)/Z ulassungen/sc hiffsz ul ass ungen/r INA (Registro Italiano N aval @ 1 Pos : /D okumentati on allgemei n/gli ederungsel emente/------leerz @ 1 Pos : 49 /D okumentation allgemei n/glieder ungs elemente/------leerz @ 1 Pos : 50 /Serie 750 ( WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/z ulass ungen/infor mation: Weitere Infor mationen zu Zul ass ungen @ 1 Pos : 51 /D okumentation allgemei n/glieder ungs elemente/------leerz @ 1 Pos : 55 /D okumentation allgemei n/glieder ungs elemente/---seitenwechs @ 1 WAGO-I/O-SYSTEM 750 Device Description 23 PRS (Polski Rejestr Statków) RINA (Registro Italiano Navale) More Information about Approvals Detailed references to the approvals are listed in the document Overview Approvals WAGO-I/O-SYSTEM 750, which you can find via the internet under: Documentation WAGO-I/O-SYSTEM 750 System Description. Pos : 52 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Gerätebesc hreibung/nor men und Ric htlini en - Übersc hrift Standards and Guidelines Pos : 53 /All e Seri en (Allgemei ne Module)/N or men und Ric htli nien/emv-n ormen - Standar d/emv CE- Stör fes tigkeit EN : @ 1 EMC CE-Immunity to interference acc. to EN : 2001 Pos : 54 /All e Seri en (Allgemei ne Module)/N or men und Ric htli nien/emv-n ormen - Standar d/emv CE- Störaussendung EN : @ 1 EMC CE-Emission of interference acc. to EN : 2007

24 24 Function Description WAGO-I/O-SYSTEM 750 Pos : 56 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/F unktions bes chr eibung - Ü berschrift Function Description Pos : 57 /Serie 753 ( WAGO-I/O-SYST EM)/F unktions beschr eibung/funkti onsbesc hrei bung When using one or more KNX modules in a KNX IP controller (or other WAGO controller), the module can exchange KNX telegrams with the IEC application. Special function blocks are required for communication between the IEC and the KNX application programs, creating the interface between the KNX objects and the IEC variables. One master function block processes the protocol to be used for the communication with the corresponding module via the internal data bus. The function blocks are made available in a library. Download function blocks for IEC-KNX communication! The function blocks used for realizing the IEC-KNX communication and general instructions for use can be found at The KNX/EIB/TP1 modules support acyclic services and acknowledgements. An opcode is used for the read/write command of data and the triggering of specific functions. With the opcodes defining the structure and content of the data bytes via their value. The data transfer through the KNX module is bidirectional, via confirmed services with integrated flow control. Because KNX is a multi master system, commands are not only transmitted from controller to module, but also sent actively and internally from the module to the controller. For example, when an event of a switch, connected to the KNX module, is sent internally via the module bus to the PFC application of the controller.

25 WAGO-I/O-SYSTEM 750 Function Description Application of Module with Programmable Fieldbus Controllers The function blocks provide the interface between the KNX communication objects of the module and the IEC application. The data formats of the function blocks are represented by data point types (DPT's). A DPT_SWITCH function block (1 bit format) may be used for, e.g., switch objects (on/off). For each DPT a separate function block is available. This enables not only the scaling, but also the individual input and output of the DPT datasets. Depending on the application, these modules may be used in the IEC application. The WAGO-ETS Plug-in filters the addresses of these function blocks from the SYM_XML file generated by the WAGO-I/O-PRO. Thus, an assignment between KNX group addresses and DPT function blocks can be created in the ETS Plug-in. In addition, the library provides a master function block controlling the communication between the KNX module and the IEC application. The data of the previously mentioned DPT modules are processed here Interworking Datapoint Types Die KNX-Klemme unterstützt die folgenden EIB-Datenbreiten: 1 7 bit 1 4 Byte 6 Byte 8 Byte 10 Byte 14 Byte Additional information about Interworking Datapoint Types! Additional information about Interworking Datapoint Types can be found at

26 26 Function Description WAGO-I/O-SYSTEM Data Exchange between KNX/EIB/TP1 Module and IEC Application The KNX module and IEC application differ in their communication method. To ensure data exchange, the KNX module requires configuring. In the IEC application, special function blocks are created for the KNX communication; their variables are imported in the KNX configuration tool ETS. Using this tool, KNX group addresses and IEC variables are connected with each other and loaded as a mapping table into the module. Thus, the IEC application and KNX module / TP1 network are configured for a common communication. 4.3 Startup Behavior of the KNX/EIB/TP1 Module in Device Mode In order for the KNX module to operate in device mode, a node is created between one WAGO controller and at least one KNX module with voltage applied. The following startup behavior is also present when the bus node is already operational and the IEC application has yet to be modified. LED A, indicating the router mode of the module, will be flashing for 30 seconds. LED E (device mode) is also flashing. The flashing signals the initialization phase of the module. At this time, functions are not yet available. In order for the KNX module to communicate with other stations in the network, an IEC program is loaded into the controller. In this program, function blocks are created which are required for the module communication. All relevant variables will be exported as network variables as a SYM_XML file from the finished program. The SYM_XML file with the IEC network variables is imported using the configuration software ETS and the WAGO-specific ETS-Plug-in. The imported network variables need to be linked with the KNX group addresses and loaded as a mapping table into the module. Telegrams are sent in the KNX net via the KNX group addresses. A checksum (CRC) is created within the controller. A fault-free download and successful check is indicated by the permanent green light of LED E. If the LED is still flashing, the IEC application requires verification. If the module has been configured and has moved into device mode, group telegrams, which were previously assigned the function Send at reset, are sent via the bus. In this process, a delay is maintained between two sequential telegrams. This delay can be set using the engineering tool software (ETS). The KNX module is now ready to function, enabling a communication between the IEC application and KNX module and - via the module - with connected TP1 networks.

27 WAGO-I/O-SYSTEM 750 Function Description 27 Figure 6: Startup behavior of the KNX module in device mode

28 28 Function Description WAGO-I/O-SYSTEM Installation Notes KNX plug only for use with KNX/EIB/TP1 module ! The KNX plug is intended exclusively for the KNX/EIB/TP1 module , because the plug is bridged between the two KNX bus conductors + and the two KNX conductors -. If the plug is operated at a different module, a short-circuit may occur. Table 10: Internal bridge in plug No Description 1 + KNX bus 2 Plug internally bridged 3 - KNX bus. KNX module is bridged internally! The plug of the KNX module is bridged internally, because the bus conductors may not be interrupted when the wiring of a module has been disconnected. Use internal system supply module for supply of further modules! The bus module is supplied via the module bus with the necessary operating voltage and does not have power contacts for the reception and transmission of FE (functional earthing/screen). If an additional 24 V supply voltage or FE is required for other bus modules, an internal system supply module must be connected on the line side of the next module. Use separate KNX supply module! The KNX module does not have its own KNX supply module. Hence, the connection of a separate KNX supply module is required.

29 Pos : 58 /D okumentation allgemei n/glieder ungs elemente/---seitenwechs @ 1 WAGO-I/O-SYSTEM 750 Function Description 29 Note the different operation modes! If one or more KNX/EIB/TP1 modules, , are operated on a KNX IP controller, it will work in device mode. The first module inserted, however, will be automatically operated in router mode. If the KNX module is operated with a different WAGO controller, the module will always be in device mode. First KNX module at KNX IP Controller works in router mode! If any controller is exchanged with a KNX IP controller , the first KNX module inserted will automatically enter the router mode. It will be impossible to access the module from the IEC application. Router function can be deactivated in the Web-Based Management system! The router function is enabled by default. However, you have the option of disabling the router function in the web based management system on the KNX page. In this case, all connected KNX modules including the first one are operated in device mode. In operating mode loss of telegrams is possible! Configuration performed with WAGO-I/O-CHECK in operating mode can lead to the loss of telegrams. Further information To install the KNX bus module at a programmable fieldbus controller, you will need the WAGO-I/O-PRO software in order to program the function blocks. In addition, the engineering tool software (ETS) with the WAGO product database, which includes the WAGO ETS Plug-in, is also required to configure the bus module. You can find the function blocks used in WAGO-I/O-PRO to realize the IEC- KNX communication, the WAGO-ETS Plug-in, and general instructions for use at The documentation for the WAGO-ETS Plug-in is available at our website ETS can be downloaded via the internet from the KNX Association at

30 Pos : 61 /D okumentation allgemei n/glieder ungs elemente/---seitenwechs @ 1 30 Process Image WAGO-I/O-SYSTEM 750 Pos : 59 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Pr oz ess abbild - Übersc hrift Process Image Pos : 60 /Serie 753 ( WAGO-I/O-SYST EM)/Proz ess abbild Kl emmenbus /Sonder klemmen/pr ozessabbild Ger @ 1 Using the KNX module, a 24-byte input and output process image can be transferred to the controller via a logical channel. Two status bytes and two control bytes provide the control of the data flow. The byte length of solely KNX telegrams varies between 7-byte minimum and 64-byte maximum (typical length is 7-byte to 24-byte). Furthermore, the internal data bus communication offers 24- byte maximum for each module bus telegram, of which 14-byte can be used for KNX telegrams. In device mode, access to the KNX data can only be performed via special function blocks of the IEC application. Configuration using the ETS engineering tool software is not required for KNX.

31 Pos: 63.2 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/vorsic ht/vorsicht: Verl etz ungsgefahr durc h s charfkantige M ess er @ 1 Pos: 63.3 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstige Hinweise/Achtung/Achtung: Busklemmen nur in vorgesehener Reihenfolg e @ 1 Pos: 63.4 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweise/Hinweis/Hi nweis: Busabsc hluss nicht vergess @ 1 Pos: 63.5 /Dokumentation allgemein/gliederungselemente/---seitenwechs @ 1 WAGO-I/O-SYSTEM 750 Mounting 31 Pos : 62 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Monti eren - D emontieren/m ontier en - Übersc hrift Mounting Pos: 63.1 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/d emontieren/m ontagerei Mounting Sequence All system components can be snapped directly on a carrier rail in accordance with the European standard EN (DIN 35). The reliable positioning and connection is made using a tongue and groove system. Due to the automatic locking, the individual components are securely seated on the rail after installation. Starting with the coupler/controller, the I/O modules are mounted adjacent to each other according to the project design. Errors in the design of the node in terms of the potential groups (connection via the power contacts) are recognized, as the I/O modules with power contacts (male contacts) cannot be linked to I/O modules with fewer power contacts. Risk of injury due to sharp-edged male contacts! The male contacts are sharp-edged. Handle the module carefully to prevent injury. Insert I/O modules only from the proper directions! All I/O modules feature grooves for power jumper contacts on the right side. For some I/O modules, the grooves are closed on the top. Therefore, I/O modules featuring a power jumper contact on the left side cannot be snapped from the top. This mechanical coding helps to avoid configuration errors, which may destroy the components. Therefore, insert I/O modules only from the right and from the top. Don't forget the bus end module! Always plug a bus end module onto the end of the fieldbus node! You must always use a bus end module at all fieldbus nodes with the WAGO I/O System 750 fieldbus couplers/controllers to guarantee proper data transfer.