L23 DeviceNet Drawing

Transcription

1 4 2 1 Cat. Number 1769-L2-QFC1 Embedded Communication Port Isolated Serial Non-Isolated Serial CompactLogix Capacity CompactLogix Configuration EtherNet/IP Connections Memory Embedded I/O (pre-configured in Logix 5000) Expansion n/a 512K 16 DC in, 16 DC out 4 nalog in, 2 nalog out. 4 High speed counters (250KHz) 2 dditional L2-QFC1 has 512K of memory and supports 2 additional I/O modules or 1 additional comm/specialty module Supports Ladder Programming, Function lock Diagram, Structured Text and Sequential Function Chart Embedded Power Supply Embedded I/O 16 DC In, 16 DC Out, 4 nalog In, 2 nalog Out 4 High Speed Counters HMI Performance With 50 tags/display and 100 alarm tags the typical update time is 2 sec PanelView Plus 600 CompactLogix L2 QFC-1 Capacity Up to 6 nodes Trunkline can be up to 500 m without repeaters Each device can be up to 6 m (20 ft) from the trunk Configuration requires a power supply to provide power to devices on the network. Several media options are available Can extend distance with repeaters HMI Capacity 200 screens 250 tags per screen PV+ 600 Phone Compactlock I/O 900-RDES Remote ccess Dial-In Paging Modem Performance Intelligent high resolution absolute encoders utomatic motor recognition Sercos, and analog Capacity V C Options, single and three-phase input 7.5 to 150 peak current Eight selectable general purpose inputs Four selectable general purpose outputs and relay output Configuration 7 segment LED for status and error codes Configuration with Ultraware Serial port for RS-22/RS-485 Indexing drive option PowerFlex 4-Class Capacity HP 120V - 600V 24vDC digital I/O nalog I/O PowerFlex 4-Class Configuration uilt-in operator display for configuration and monitoring Remote (Nema 1 & 4) HIM options DriveExecutive software tool options PowerFlex 4-Class Performance V/Hz or SVC Slip compensation 40:1 speed range "Multi-Drive" feature allows up to 5 drives per node Serial peripheral interface (19.2K bps) PowerFlex 4- Component Class Drive 1606 Power Supply E Overload Capacity The maximum is 6 modules per adapter The adapter supplies 1 amp of current to the backplane, enough for 1 digital I/O modules. To connect additional I/O modules, add 174-EP24VDC Expansion Power Units as needed. Each one passes 1. amps of current to the modules on its right -- enough for 17 digital modules. Other I/O modules draw more current so refer to the published specs. Compactlock I/O ase blocks contain a maximum of 16 digital or 4 analog I/O. uilt-in or PROFIUS DP network adapter. Thermocouple and RTD base blocks are also available. Compactlock LDX digital I/O base blocks support up to three expansion blocks, for a maximum of 64 I/O points Inputs and outputs are powered by an external 24V dc source that is independent of the network. Publication ISIMP-QR011-EN-P pril, 2008 Note: Performance is what we tested, not the max capacity L2 Drawing 4 2 1

2 System: Controller Hardware L2 COMPCTLOGIX L2-QFC1 PROCESSOR HMI Hardware P-T6C5D PNELVIEW PLUS 600 COLOR TOUCH TERMINL Distributed I/O Hardware DN 174 DEVICENET DPTER FPD FIELD POTENTIL DISTRIUTOR I2 120 VC 2 CHNNEL INPUT MODULE O2 120/20 VC 2 CHNNEL OUTPUT MODULE T MODULE SE W/ REMOVLE IEC SCREW TERMINLS Distributed I/O Hardware - Compactlock D-T4T0 DNET LDX 4 INPUT THERMOCOUPLE SE TERMINL LOCK T16VOVX 24 LDX, VDC 16 UNIVERSL IN EXPNSION TERMINL LOCK TOW8X 8 LDX, RELY OUTPUT EXPNSION TERMINL LOCK DSD-XXX V, Three-phase with ill of Material bout this Configuration: L2 System This CompactLogix based system with two integrated serial ports and an add-on communication module offer an economical solution to serve a variety of applications. It matches the basic layout of a classic control system, but provides the functionality of the Integrated rchitecture. bout the Products Drive Hardware P5N114 POWERFLEX 4 DRIVE 1 22-COMM-D POWERFLEX 4DEVICENET INTERFCE 1 22-XCOMM-DC EXTERNL DSI COMM SE KIT Note: PowerFlex drives come in many variations - before ordering, you will need to identify voltage rating, horsepower, enclosure type. In addition, you may wish to add on optional equipment, such as HIM module or rake Resister. Please refer to the PowerFlex Selection Guide for additional details on selecting the right drive for you application DSD-XXX V, Drive Three-phase with Distributed Devicenet Devices 1 19-EC1 E ELECTRONIC OVERLOD RELY, 100-C09...C2, 1-5 CONFIGURTION TOOL REQUIRED RLS200ENE* RSLOGIX 5000 MINI LDDER ONLY Note: CompactLogix Controllers can be programmed using RSLogix 5000 Mini, Lite, Standard, or Pro. If you plan to use the four programming languages purchase the Lite edition VWM015ENE FCTORY TLK VIEW MCHINE EDITION DNETL RSNETWORX FOR DEVICENET Logix Controllers common set of controls, networks, and programming software available in multiple hardware platforms Multiple control disciplines in a single controller - sequential / drives / process Multiple Program Languages available in all controllers - Ladder Diagram, Function lock, Structured Text, and Sequential Function Chart Embedded RS-22 port provides remote access as well as SCII, DH-485, DF-1, Modbus Master/Slave and bridging to other networks enabling remote device configuration Tag-based architecture instead of addresses PanelView Plus Reuse tags from Logix controllers by choosing them from a list 4 15 screen sizes available Touchscreen, keypad or combination Integrated EtherNet/IP and RS-22 (most models), add-on for many other networks dvanced Operator Interface features such as trending, expressions, data logging, animation. Compactlock LDX I/O Compactlock LDX I/O is ideally suited for light industrial and commercial applications. Compact design of hardware lets it fit into shallow enclosures and confined areas. and PROFIUS DP are supported. Up to 64 points can be addressed on a single network node. I/O types include C/DC, analog, RTD, and thermocouple. Choice of D-shell connector for convenient disconnection or fixed screw terminals for I/O connections. PowerFlex Drives Serves applications ranging from 0.2 kw (0.25 hp) to 6,770 kw (9,000 hp). Common set of networks, operator interface and programming for all PowerFlex drives Communication Options Ethernet/IP, ControlNet, Devicenet, DH Plus, RIO, rd party networks Hundreds of pieces of status and diagnostic information are shared with Logix controllers directly vailable in IP-20 or IP-67 styles Densities from 2-8 points per module Removable screw or spring terminals without rewiring Mounts horizontally or vertically with no derating required Supports EtherNet/IP, ControlNet, and rd party networks 20V serves applications from 0.5 to 15kW, continuous output current 2.5 to 65 mps with peak output current from 7.5 to 150 mps. 460V serves applications from to 22 kw, continuous output current from 7 to 47 mps with peak output current from 14 to 94 mps. uilt-in support for multi-turn absolute encoders with option to supply external logic power to maintain position during power loss. i's built-in indexing can eliminate the need for a motion controller or PLC Card for point to point positioning moves. RSLogix 5000 is only software required for both sequential and motion control. For More Information and Help For more information contact your local distributor or Rockwell utomation sales representative. Publication Library My Support Z Product Directory

3 4 2 1 CompactLogix L2 Comparison Cat. Number 1769-L2E-Q L2E-QFC1 CompactLogix Capacity Embedded Communication Port EtherNet/IP Connections Memory Embedded I/O (pre-configured in Logix 5000) Expansion 8 TCP/IP-2 CIP 512K 16 DC in. 16 DC out. 2 dditional 8 TCP/IP-2 CIP 512K 16 DC in, 16 DC out 4 nalog in, 2 nalog out. 4 High speed counters (250KHz) 2 dditional Ethernet Performance EtherNet/IP provides excellent drive and I/O control performance along with HMI, information processing and many commercial technologies. L2E-QFC1 has 512K of memory and supports 2 additional I/O modules or 1 additional comm/specialty module Supports Ladder Programming, Function lock Diagram, Structured Text and Sequential Function Chart CompactLogix L2E QFC-1 I/O I/O CompactLogix Configuration Embedded Power Supply Embedded I/O 16 DC In, 16 DC Out, 4 nalog In, 2 nalog Out 4 High Speed Counters CompactLogix Performance Ethernet/IP connections: 8 TCP/IP - 2 CIP PanelView Plus 600 HMI Capacity 200 screens 250 tags per screen PV+ 600 HMI Performance With 50 tags/display and 100 alarm tags the typical update time on is 2 sec 900-RDES Remote ccess Dial-In Ethernet Modem Phone PowerFlex 4-Class Capacity HP 120V - 600V 24vDC digital I/O nalog I/O Internal EtherNet/IP adapter on PowerFlex 40 PowerFlex 4-Class Configuration uilt-in operator display for configuration and monitoring Remote (Nema 1 & 4) HIM options DriveExplorer and DriveExecutive software tool options PowerFlex 4-Class Performance V/Hz or SVC Slip compensation 40:1 speed range EtherNet/IP allows complete access to data in drive "Multi-Drive" feature allows up to 5 drives per node Serial peripheral interface (19.2K bps) PowerFlex 4- Component Class Drive Capacity The maximum is 6 modules per adapter The adapter supplies 1 amp of current to the 1 digital I/O modules. To connect additional I/O modules, add 174-EP24VDC Expansion Power Units as needed. Each one passes 1. amps of current to the modules on its right -- enough for 17 digital modules. Other I/O modules draw more current so refer to the published specs. Publication ISIMP-QR011-EN-P pril, 2008 Note: Performance is what we tested, not the max capacity L2E Drawing 4 2 1

4 ill of Material bout this Configuration: L2E System System: Controller Hardware L2E COMPCTLOGIX L2E PROCESSOR IQ16 16 POINT 24 VD SINKING/ SOURCING INPUT MODULE O16 16 POINT 24 VDC SOURCING OUTPUT MODULE HMI Hardware P-T6C20D PNELVIEW PLUS 600 COLOR TOUCH TERMINL Distributed I/O Hardware ENT 174 ETHERNET/IP DPTER FPD FIELD POTENTIL DISTRIUTOR I2 120 VC 2 CHNNEL INPUT MODULE O2 120/20 VC 2 CHNNEL OUTPUT MODULE T MODULE SE W/ REMOVLE IEC SCREW TERMINLS PS VC TO 24 VDC 1. POWER SUPPLY Drive Hardware P5N114 POWERFLEX 4 DRIVE 1 22-COMM-E POWERFLEX 4 ETHERNET INTERFCE Note: PowerFlex drives come in many variations - before ordering, you will need to identify voltage rating, horsepower, enclosure type. In addition, you may wish to add on optional equipment, such as HIM module or rake Resister. Please refer to the PowerFlex Selection Guide for additional details on selecting the right drive for you application. CONFIGURTION TOOL REQUIRED RLS200ENE* RSLOGIX 5000 MINI LDDER ONLY Note: CompactLogix Controllers can be programmed using RSLogix 5000 Mini, Lite, Standard, or Pro. If you plan to use the four programming languages purchase the Lite edition VWM015ENE FCTORYTLK VIEW MCHINE EDITION DNETL RSNETWORX FOR DEVICENET This CompactLogix based system with integrated EtherNet/IP offers a single network solution for high-speed I/O control, drive control and controller-to-controller interlocking as well as easy integration with the business system, the Internet and commercial Ethernet technologies. Devices connected to Ethernet/IP feature embedded web pages that provide diagnostics information for troubleshooting from any standard web browser. bout the Products Logix Controllers common set of controls, networks, and programming software available in multiple hardware platforms Multiple control disciplines in a single controller - sequential / motion / drives / process Multiple Program Languages available in all controllers - Ladder Diagram, Function lock, Structured Text, and Sequential Function Chart Embedded RS-22 port provides remote access as well as SCII, DH-485, DF-1, Modbus Master/Slave and bridging to other networks enabling remote device configuration Tag-based architecture instead of addresses PanelView Plus Reuse tags from Logix controllers by choosing them from a list 4 15 screen sizes available Touchscreen, keypad or combination Integrated EtherNet/IP and RS-22 (most models), add-on for many other networks dvanced Operator Interface features such as trending, expressions, data logging, animation. PowerFlex Drives Serves applications ranging from 0.2 kw (0.25 hp) to 6,770 kw (9,000 hp). Common set of networks, operator interface and programming for all PowerFlex drives Communication Options Ethernet/IP, ControlNet, Devicenet, DH Plus, RIO, rd party networks Hundreds of pieces of status and diagnostic information are shared with Logix controllers directly vailable in IP-20 or IP-67 styles Densities from 2-8 points per module Removable screw or spring terminals without rewiring Mounts horizontally or vertically with no derating required Supports EtherNet/IP, ControlNet, and rd party networks For More Information and Help For more information contact your local distributor or Rockwell utomation sales representative. Publication Library My Support Z Product Directory

5 4 2 1 CompactLogix L2 Comparison Cat. Number 1769-L2E-Q L2E-QFC1 Embedded Communication Port EtherNet/IP Connections Memory Embedded I/O (pre-configured in Logix 5000) 8 TCP/IP-2 CIP 512K 16 DC in. 16 DC out. 8 TCP/IP-2 CIP 512K 16 DC in, 16 DC out 4 nalog in, 2 nalog out. 4 High speed counters (250KHz) CompactLogix Capacity L2E-Q1 has 512K of memory and supports 2 additional I/O modules or 1 additional comm/specialty module Supports Ladder Programming, Function lock Diagram, Structured Text and Sequential Function Chart CompactLogix Configuration Embedded Power Supply Embedded I/O 16 DC In, 16 DC Out, 4 nalog In, 2 nalog Out 4 High Speed Counters Expansion HMI Performance With 50 tags/display and 100 alarm tags the typical update time is 2 sec 2 dditional 2 dditional CompactLogix L2E Capacity Up to 6 nodes Trunkline can be up to 500 m without repeaters Each device can be up to 6 m (20 ft) from the trunk Configuration requires a power supply to provide power to devices on the network. Several media options are available Can extend distance with repeaters PanelView Plus 600 HMI Capacity 200 screens 250 tags per screen PV RDES Remote ccess Dial-In Paging Modem Phone Performance Intelligent high resolution absolute encoders utomatic motor recognition Sercos, and analog Capacity V C Options, single and three-phase input 7.5 to 150 peak current Eight selectable general purpose inputs Four selectable general purpose outputs and relay output Configuration 7 segment LED for status and error codes Configuration with Ultraware Serial port for RS-22/RS-485 Indexing drive option PowerFlex 4-Class Capacity HP 120V - 600V 24vDC digital I/O nalog I/O PowerFlex 4-Class Configuration uilt-in operator display for configuration and monitoring Remote (Nema 1 & 4) HIM options DriveExecutive software tool options PowerFlex 4-Class Performance V/Hz or SVC Slip compensation 40:1 speed range "Multi-Drive" feature allows up to 5 drives per node Serial peripheral interface (19.2K bps) PowerFlex 4- Component Class Drive 1606 Power Supply E Overload Capacity The maximum is 6 modules per adapter The adapter supplies 1 amp of current to the backplane, enough for 1 digital I/O modules. To connect additional I/O modules, add 174-EP24VDC Expansion Power Units as needed. Each one passes 1. amps of current to the modules on its right -- enough for 17 digital modules. Other I/O modules draw more current so refer to the published specs. Compactlock I/O Compactlock I/O ase blocks contain a maximum of 16 digital or 4 analog I/O. uilt-in adapter. Thermocouple and RTD base blocks are also available. Compactlock LDX digital I/O base blocks support up to three expansion blocks, for a maximum of 64 I/O points Inputs and outputs are powered by an external 24V dc source that is independent of the network. Publication ISIMP-QR011-EN-P pril, 2008 Note: Performance is what we tested, not the max capacity L2E with Drawing 4 2 1

6 System: Controller Hardware L2 COMPCTLOGIX L2-QFC1 PROCESSOR HMI Hardware P-T6C5D PNELVIEW PLUS 600 COLOR TOUCH TERMINL Distributed I/O Hardware DN 174 DEVICENET DPTER FPD FIELD POTENTIL DISTRIUTOR I2 120 VC 2 CHNNEL INPUT MODULE O2 120/20 VC 2 CHNNEL OUTPUT MODULE T MODULE SE W/ REMOVLE IEC SCREW TERMINLS Distributed I/O Hardware - Compactlock D-T4T0 DNET LDX 4 INPUT THERMOCOUPLE SE TERMINL LOCK T16VOVX 24 LDX, VDC 16 UNIVERSL IN EXPNSION TERMINL LOCK TOW8X 8 LDX, RELY OUTPUT EXPNSION TERMINL LOCK ill of Material Drive Hardware P5N114 POWERFLEX 4 DRIVE 1 22-COMM-D POWERFLEX 4DEVICENET INTERFCE 1 22-XCOMM-DC EXTERNL DSI COMM SE KIT Note: PowerFlex drives come in many variations - before ordering, you will need to identify voltage rating, horsepower, enclosure type. In addition, you may wish to add on optional equipment, such as HIM module or rake Resister. Please refer to the PowerFlex Selection Guide for additional details on selecting the right drive for you application DSD-XXX V, Drive Three-phase with Distributed Devicenet Devices 1 19-EC1 E ELECTRONIC OVERLOD RELY, 100-C09...C2, 1-5 CONFIGURTION TOOL REQUIRED RLS200ENE* RSLOGIX 5000 MINI LDDER ONLY Note: CompactLogix Controllers can be programmed using RSLogix 5000 Mini, Lite, Standard, or Pro. If you plan to use the four programming languages purchase the Lite edition VWM015ENE FCTORY TLK VIEW MCHINE EDITION DNETL RSNETWORX FOR DEVICENET bout this Configuration: L2E with System This CompactLogix based system with two integrated serial ports and an add-on communication module offer an economical solution to serve a variety of applications. It matches the basic layout of a classic control system, but provides the functionality of the Integrated rchitecture. bout the Products Logix Controllers common set of controls, networks, and programming software available in multiple hardware platforms Multiple control disciplines in a single controller - sequential / drives / process Multiple Program Languages available in all controllers - Ladder Diagram, Function lock, Structured Text, and Sequential Function Chart Embedded RS-22 port provides remote access as well as SCII, DH-485, DF-1, Modbus Master/Slave and bridging to other networks enabling remote device configuration Tag-based architecture instead of addresses PanelView Plus Reuse tags from Logix controllers by choosing them from a list 4 15 screen sizes available Touchscreen, keypad or combination Integrated EtherNet/IP and RS-22 (most models), add-on for many other networks dvanced Operator Interface features such as trending, expressions, data logging, animation. Compactlock LDX I/O Compactlock LDX I/O is ideally suited for light industrial and commercial applications. Compact design of hardware lets it fit into shallow enclosures and confined areas. and PROFIUS DP are supported. Up to 64 points can be addressed on a single network node. I/O types include C/DC, analog, RTD, and thermocouple. Choice of D-shell connector for convenient disconnection or fixed screw terminals for I/O connections. PowerFlex Drives Serves applications ranging from 0.2 kw (0.25 hp) to 6,770 kw (9,000 hp). Common set of networks, operator interface and programming for all PowerFlex drives Communication Options Ethernet/IP, ControlNet, Devicenet, DH Plus, RIO, rd party networks Hundreds of pieces of status and diagnostic information are shared with Logix controllers directly vailable in IP-20 or IP-67 styles Densities from 2-8 points per module Removable screw or spring terminals without rewiring Mounts horizontally or vertically with no derating required Supports EtherNet/IP, ControlNet, and rd party networks 20V serves applications from 0.5 to 15kW, continuous output current 2.5 to 65 mps with peak output current from 7.5 to 150 mps. 460V serves applications from to 22 kw, continuous output current from 7 to 47 mps with peak output current from 14 to 94 mps. uilt-in support for multi-turn absolute encoders with option to supply external logic power to maintain position during power loss. i's built-in indexing can eliminate the need for a motion controller or PLC Card for point to point positioning moves. RSLogix 5000 is only software required for both sequential and motion control. For More Information and Help For more information contact your local distributor or Rockwell utomation sales representative. Publication Library My Support Z Product Directory