Reliance Electric GV3000/SE Industrial AC Drive

Transcription

1 Reliance Electric GV3000/SE Industrial AC Drive Multi-Purpose variable speed control of HP three-phase motors, with Volts/Hertz or Vector mode operation as standard

2 FLEXIBLE Control Whether you need a simple drive for operating fans and pumps, or a high performance drive for a web processing system requiring both speed and torque control, the GV3000/SE will do all this and more. Every GV3000/SE provides 3 methods of operation Volts/Hertz Control Sensorless Vector Control Flux Vector Control Out-of-the-box---standard--- with nothing else to buy, it s 3 drives in 1. One Drive One Price No Boards Required

3 Power Unit General Purpose Mode (V/Hz) Motor FLA Vector Mode (SVC, FVC) 110% 100% Amps Overload Constant Torque Curve Variable Torque Curve Hz Base Hz Motor Speed Overload 1 minute 150% Constant Torque Curve 100% Amps Base RPM Motor Speed General Purpose Mode Volts/Hertz allows classical variable speed control of single or multiple motors from one drive. Operate either squirrel-cage induction or permanent magnet synchronous AC motors in this control mode. It s ideal for applications such as centrifugal fans and pumps, or conveyor applications. Vector Mode allows operation in either open loop Sensorless Vector control or closed loop Flux Vector control. Selection between the two is done simply by selecting the Encoder PPR value. Choose a numerical PPR for closed loop operation, or choose SE for Sensorless Enhanced open loop operation. In most cases, tuning the drive isn t even necessary when switching between Sensorless and Flux Vector control due to the shared parameter set used for both methods of control.

4 VERSATILE Packaging Whether it s a stand-alone design to be mounted in a harsh environment, or a panel-mounted drive designed specifically to save you valuable space and installation time, the GV3000/SE allows you to choose from multiple enclosures in order to select the packaging design that s just right for your application needs. Washdown duty-- ideal for food processing environments. eep dust and dirt from contaminating the drive without the cost of a separate enclosure. Designed for direct connection to conduit in stand-alone areas. Stand-alone Packaging for Wall, Machine & Floor Mounting NEMA 4X / IP54 Drives (Washdown) 200 to 230 VAC 380 to 460 VAC 1 to 5 HP 1 to 5 HP NEMA 12 / IP52 Drives (Dust Tight) 200 to 230 VAC 380 to 460 VAC 1 to 20 HP 1 to 60 HP NEMA 1 (*1A) / IP20 Drives (Ventilated) 200 to 230 VAC 380 to 460 VAC 380 to 460 VAC 1 to 20 HP 1 to 150 HP *200 to 400 HP

5 IEC-rated design for space optimization. Includes 7th IGBT for braking. High power density allows retrofit of old DC applications. Modular enclosure simplifies matching into line-ups. Bookshelf Packaging for Panel Mounting IP20 Bookshelf Drives (Finger-Safe) Power Module Packaging for Panel Mounting IP0 Power Modules (Exposed Power Terminals) 380 to 460 VAC 2.1 to 30 Amps 200 to 230 VAC 380 to 460 VAC 30 to 100 HP 75 to 200 HP

6 SIMPLE Operation and Setup Built into every GV3000/SE is this simple to use display and keypad. Bright LEDs provide clear indication of programming, operating, and monitoring values. Arrow keys are used to change speed as well as to change data. Monitoring of motor operation is done easily by pressing the ENTER key. This allows you to scroll through each monitor display by pressing only one key. Other indicators provide operation and directional information in the same intuitive manner.

7 Optional Operator Interface Module The Operator Interface Module (OIM) provides a remotemounted drive interface. The large, easy-to-read graphical display and function keys allow simple operator control, monitoring, and diagnostics. A built-in help menu provides clear descriptions of drive setup and operation. Help Menu Provides text description of parameter operation and use Eliminates the need to refer to instruction manuals Provides description of OIM operation Monitor Operation Select 2, 4, or 6 lines of motor information Adjust text contrast for readability View intuitive status messages without selecting menus Main Menu display allows selection Quick Start Speed Control Application Setup Performance Tuning Motor Data Setup is made easy with self-prompting menus and parameter groupings. Drive Status Regulator Terminal Strip Option Port Configuration Memory Functions Additional Parameters Displays can be shown in 5 languages. Language Menu English Deutsch Français Español Italiano

8 INTUITIVE Software There s no easier way to configure, document, and maintain your drive than with the optional CS3000 software. For PC-based configuration, control, monitoring, and diagnostics, use CS3000 software. CS3000 operates under both Windows 3.1 and Windows 95 operating systems. Connection over a standard RS-232 cable between the built-in GV3000/SE 9-pin D-shell and your PC allows you to quickly and easily set up the drive. The CS3000 software provides the same functionality with FlexPak 3000 DC drives.

9 CS3000 Version 6.0 with PC Scope Now, with the power of an oscilloscope on your PC, use the PC Scope feature to tune, diagnose, and analyze the performance of your application. Data can be saved as scope trace files or converted to ASCII for use in a spreadsheet. Overlay new scope traces over old with the Snapshot function to tune machine performance. Create a custom list of 20 tuning parameters to aid in application setup. Changes are downloaded immediately for you to observe in your application. The Configuration Editor allows you to select and configure drive parameters at the drive or at your desk. Upload and download parameter settings from drive to drive. Save parameters as files for future reference and for ease of printing. Upload and compare parameter file settings to identify possible parameter changes. From your PC you can operate the drive and monitor motor performance, including speed, current, voltage, torque, and kw.

10 EMBEDDED Solutions Option boards for various needs mount cleanly inside every GV3000/SE design. Network communications and I/O expansion cards connect directly to the GV3000/SE Regulator through a high-speed dual-port connection. With either of these options installed, you can take advantage of GV3000/SE s inner and outer control loops to adapt to any application. Communicate to GV3000/SE on AutoMax, DeviceNet or other networks. A dual-port connection allows direct access to the 32-bit, Motorola68332 processor for quick acknowledgement and response in networked applications. I/O expansion allows terminal connections for more advanced drive control: PI setpoint control Outer loop trim of speed or torque for: - Inertia compensation - Current compounding Frequency input Additional preset speeds Assign relay outputs for: - Speed & torque setpoints - On-Delay logic OR Isolated digital & analog I/O expansion with Super RMI card OR 115 VAC to 24 VDC Control Interface card

11 Standard parameters for web processing applications. Trim Reference From Network Or RMI Analog Input OCL Intergral Gain (U.046) OCL Proportional Gain (U.045) OCL Trim Range (U.047) OCL Reference Gain (U.044) OCL Feedback* GV3000/SE Outer Control Loop (OCL) Block Diagram 20 msec Scan Period _ * Reset OCL Lead/Lag Select (U.041) PI Reset Lead/ Lag * OCL Enabled (Drop 1, Reg 32, Bit 5) Top Speed Divide Network OCL Enable Bit (Drop 1, Reg 32, Bit 5) Or RMI Digital Input Running OCL Lead/Lag Ratio (U.043) OCL Feedback Select (.040) OCL Lead/Lag Low Freq (U.042) Multiply OCL Proportional Trim Enable (U.048) IXI * * Scaled Terminal Strip Analog Input Input Gain (P.010) OCL Output (To SpeedLoop Block Diagram) *Available In Network Read Registers Speed Reference S-Curve Block Output (From Speed Loop Block Diagram) Speed PI Output (Torque Ref.) Input Offset (P.009) Terminal Strip Analog Input (10 Bit= /-1023) Compensate for inertia build-up in winders. Load-share between motors in multi-drive roll sections such as calendars. The outer control loop utilizes a 20-msec update, allowing use in both dancer-controlled and tension-controlled winder applications. Trim a speed or torque main reference with an analog input from the Remote Meter Interface card or over one of several available network options. Speed Reference Trim Reference Select (P.014) Draw Gain (P.016) Trim Gain (P.015) O GV3000/SE SPEED Loop Block Diagram 5 msec Update for Speed Commands/ 0.5 msec Update for Torque Commands (P.004) Maximum Speed Minimum Speed (P.003) Fwd/Rev 0 OCL Output (from OCL Block Diagram) Speed PI Low Limit (To Outer Control Loop) /_ Top Speed Speed PI * High Limit Lo Hi S-Curve PI *Available In Network Read Registers * Network Inertia Compensation (Drop 1, Reg 35 ) Rate Output Speed Feedback Current Compounding Current Compounding Gain (U.026) Losses Compensation Loss Gain (U.028) Speed PI* Output Inertia Compensation (WR2) Inertia Compensation Gain (U.027) Network Inertia Compensation Enable (Drop 1, Reg 53, Bit 1) * Torque Reference Iq Ref. High Limit Iq Ref. Low Limit Torque Loop * Torque Feedback (To Outer Control Loop)

12 ADAPTABLE in Application For demanding applications that were once dominated by DC drives and other control technologies, look to the GV3000/SE in Vector Mode for high performance along with reduced operating and maintenance costs. APPLICATIONS Extruders Material Handling Web Processing Punch Presses Test Stands Metering Pumps PERFORMANCE FEATURES Low speed operation w/100% torque & 0.01% speed regulation Command 0 RPM w/ 100% torque continuous operation Inertia compensation and load sharing capabilities Up to 200% starting torque plus high bus avoidance capability Switch from speed to torque control on-the-fly Use on motion controllers for positioning w/1000 rad/sec response

13 Braking and 4-quadrant operation: Snubber Braking kits External Snubber kits are available in 2 styles, open frame and NEMA 1/IP2O. AC Drive With braking kits, you can: Match brakes to handle load peak energy demand Match brakes to handle duty cycle for energy dissipation L1 L2 L3 Diode Bridge DC Bus Fly-Back Diode Allows Energy Back to DC Bus Resistor Ohms & Watts Sized to Load Peak Energy & Duty Cycle Motor Snubber Resistor it NEMA 1 / IP20 enclosed, self-contained transistor circuit with resistors Line Regeneration Open frame, transistor-only circuits for panel mounting Power each GV3000/SE through the DC bus instead of the AC line inputs. The SS4000 Synchronous Rectifier acts as a line regeneration module to recover energy, as well as a DC bus supply for coordinated multi-drive applications. It can also be used strictly for line regeneration when desired. Overhauling loads occur when load torque exceeds motor torque. Energy is regenerated to the drive, raising the DC Bus voltage. The snubber brake dissipates the excess energy into heat for a regulated braking action. L1 L2 L3 - Drives are powered directly through the DC bus instead of the AC line and diode bridge. Regenerative energy is shared between motoring and regenerating drives, saving power. Energy is recovered back to the 3-phase AC Line instead of being dissipated into heat.

14 PowerMatched Drives and Motors Regardless of your application needs, Reliance Electric has a PowerMatched drive and motor solution for your needs. Nobody offers a larger variety of motors designed especially for use on IGBT-based PWM AC drives. Consider these important advantages when you choose a motor for connection to your Reliance AC drive: 1,600 VAC insulation systems are standard on PowerMatched Reliance AC motors for maximum protection against reflected waves in 460VAC applications with long motor lead lengths. The broadest variety of mechanical motor options including NEMA and IEC frames, motor-mounted brakes, optical encoders, constant speed air-over blowers, and a multitude of enclosure designs. GV3000/SE drives are tested with Reliance Electric AC motors to assure reliability from a single source. Environment-specific motor package including Washdown Duty and Hazardous Duty (Division I, Explosion Proof) packages with encoder feedback for Flux Vector operation.

15 Choose from E-Master, XE, and VXS motor families for all applications from 1 HP to 400 HP and a broad variety of motor enclosures and options. NEMA 4X Washdown products easily meet food processing requirements with stock drives and motors for both open loop and closed loop applications. Large horsepower drives with air-over blower-cooled VXS motors easily solve tough application needs with single source responsibility. Power modules with RPM-AC motors provide high performance and compact size, making these packages an excellent choice when retrofitting older DC applications.

16 Global Technical Services Rockwell Automation Global Technical Services provides comprehensive training for all Reliance drives products. For information on class availability and pricing, call RELIANCE ( ). Performance Driven To find out how Reliance Electric can help you meet the productivity and performance demands of your application, call or FAX today: Toll Free FAX To obtain the latest information about Reliance Electric products, services, career opportunities, and contacts worldwide, visit us on line at This document is located at: IMPORTANT NOTICE This brochure is not intended to provide operating instructions. Appropriate Rockwell Automation instruction manuals and precautions attached to apparatus should be read carefully prior to installation, operation, and/or maintenance of equipment by Rockwell International Corporation Reliance, AutoMax, DeviceNet and PowerMatched are trademarks of Rockwell Automation. Motorola is a trademark of Motorola, Inc. Windows 3.1 and Windows 95 are trademarks of Microsoft Corporation. CERTIFIED Reliance Electric / Tungsten Road / Cleveland, OH Printed in the U.S.A. D M