indoor air quality and energy saving TECHNICAL DATA FAN-T AIR VENTILATION UNITS

Transcription

1 indoor air quality and energy saving TEHNIL DT FN-T IR VENTILTION UNITS

2 FN-T ventilation unit with casing equipped for forward blade centrifugal ventilators coupled with three-phase electric motors via belt/pulley transmission. FN-T is available in 9 ventilator sizes: from 2, to 45, m³/h. MODES OF OPERTION The availability of the various electrical motor powers which can be combined with each ventilator and the appropriate selection of the pulley and belt dimensions enable configuration of FN-T to work in the desired work point. To avoid vibration transmission to the air distribution system, the ventilator is connected to the supply side with a specific vibration-proof joint and the ventilator/electric motor is connected to the base of the FN-T with vibration-proof joints. The use of three-phase electric motors enables management of FN-T in various ways: onnection of the electrical power supply only ensures FN-T works at the maximum available flow rate; Use of a regulator for phase cutoff (accessory RVT 6 or RVT 9 for electric power motors up to 4 kw) to change the rotation speed of the ventilator and therefore the air flow rate. lternatively to the phase cutoff regulators, an inverter can be used. STRUTURE FN-T was created with extruded aluminium profiles and is available both in the 25 mm thick sandwich panels version, insulated with polyurethane foam, and the version with simple panelling. The panels are manufactured in luzinc, material that ensures high strength against corrosion and oxidation. Specify when ordering: - Operating point (flow and pressure) - Position of the inspection side if different from the standard (see page 8) ONFIGURTION FN-T FROM 9/9 T 18/18 ONFIGURTION FN-T FROM TO 71 2

3 PERFORMNES The unit must be ducted properly: UTEK authorizes the use only according to its performance diagram shown into this catalogue FN-T 9/9,75 kw NO ERP 1,1 kw NO ERP FN-T 1/1,75 kw 1,1 kw 1,5 kw 2,2 kw NO ERP NO ERP NO ERP NO ERP

4 PERFORMNES The unit must be ducted properly: UTEK authorizes the use only according to its performance diagram shown into this catalogue FN-T 12/12 9,75 kw 1,1 kw 1,5 kw 2,2 kw 3, kw NO ERP NO ERP NO ERP NO ERP NO ERP FN-T 15/15 1,1 kw 1,5 kw 2,2 kw 3, kw 4, kw NO ERP NO ERP NO ERP NO ERP NO ERP

5 PERFORMNES The unit must be ducted properly: UTEK authorizes the use only according to its performance diagram shown into this catalogue FN-T 18/18 1,5 kw 2,2 kw 3, kw 4, kw 5,5 kw 7,5 kw NO ERP NO ERP NO ERP NO ERP NO ERP NO ERP FN-T 9 3, kw 4, kw 5,5 kw 7,5 kw NO ERP NO ERP NO ERP NO ERP

6 PERFORMNES The unit must be ducted properly: UTEK authorizes the use only according to its performance diagram shown into this catalogue FN-T 56 3, kw 4, kw 5,5 kw 7,5 kw 3, kw 4, kw 5,5 kw 7,5 kw FN-T 63 3, kw 4, kw 5,5 kw 7,5 kw 3, kw 4, kw 5,5 kw 7,5 kw

7 PERFORMNES The unit must be ducted properly: UTEK authorizes the use only according to its performance diagram shown into this catalogue FN-T , kw 4, kw 5,5 kw 7,5 kw 11 kw 15 kw NO ERP NO ERP NO ERP NO ERP NO ERP NO ERP 2 2 ELETRIL DT ENGINES POWER VOLTGE URRENT N. PHSES FREQUENY,75 Kw /23 1,81/3,15 3 1,1 Kw /23 2,82/4,91 3 1,5 Kw /23 3,47/6,1 3 2,2 Kw /23 4,82/8, Kw /23 6,49/11, Kw /23 8,1/14,9 3 5,5 Kw 69/ 6,62/11,42 3 7,5 Kw 69/ 8,6/14, Kw 21, Kw 69/ 16,1/27,8 3 RPM

8 DIMENSIONS (mm) WEIGHT (kg) E H D P UNIT L H P D E Peso FN-T 9/ FN-T 1/ , FN-T 12/ , FN-T 15/ FN-T 18/ , E D H 12 L P UNIT L H P D E Peso FN-T FN-T FN-T FN-T

9 INSTLLTION FN-T INSTLLTION from 7/7 to 18/18 N: = opening inspection panel Minimum required space for maintenance (mm) MOD. FN-T 7-7 FN-T 9/9-1/1 FN-T 12/12 FN-T 15/15-18/ NOT : = apertura pannello ispezione DIMENSIONI ( in mm) MODELLO 7/7 9/9-1/1 12/ /15-18/

10 INSTLLTION FN-T INSTLLTION from to 71 EXTRORDINRY MINTENNE Minimum required space for maintenance (mm) MOD. FN-T FN-T 56 FN-T 63 FN-T SPZI MNUTENZIONE STRORDINRI : sostituzione ventilatore, ecc. DIMENSIONI ( in mm ) MODELLO

11 INSTLLTION FN-T INSTLLTION from to 71 ORDINRY MINTENNE Minimum required space for maintenance (mm) MOD. FN-T FN-T 56 FN-T 63 FN-T S P Z I MN U T E N Z I ON E OR D I N R I : tens ionam ent o cingh ia, ecc. DIMENSIONI ( in mm ) MODELLO

12 Dear ustomer Thanks for your attention to the product UTEK, designed and manufactured to ensure the real values to the User : Quality, Safety and Savings on working. UTEK S.r.l. Made in italy UTEK reserves the right to at any time the necessary changes to improve products without prior notice. the Dealer FN-T_216_1_EN IR VENTILTION UNITS UTEK S.r.l. Via Provinciale,3 233 Mazzo di Valtellina (So) Italy Tel Fax utek@utek.it