SG300 BT. Wireless HandHeld CCD Scanner. Quick Guide
|
|
- Merryl Jefferson
- 7 years ago
- Views:
Transcription
1 SG300 BT Wireless HandHeld CCD Scanner Quick Guide
2
3 Table of contents 1. Introduction Illustration Quick Start Standard Shipment Package Start Up User s Manual Installation Environment Requirement Cradle Installation to the Host Device Cable installation Skip resistant pad position Program Sequence Programming flow chart Factory Default Settings General Process Set All Default Interface RS232 Parameters Baudrate Parity Data bits Stop bits Postambles Postamble Bluetooth Setup Scanner Mode Memory Mode Sleep Mode Symbologies Enable All Symbologies Enable / Disable Symbologies... 16
4 1. Introduction Thank you for purchasing this hand held long-range barcode scanner. This BT wireless hand-held longrange CCD scanner features a freedom of scanning without the limitation of cable. Thanks to the userfriendly two-way communication, the operator will be alarmed if the scanned result was not reached the receiving cradle. This scanner can be operated at 10 Meters range in open space and it can be upgraded to 100 Meters range for optional. The receiving cradle includes BT receiver and batteries charger. The charger cradle and scanner charger jack have been reserved for special request. 1.1 Illustration 1
5 2. Quick Start 2.1 Standard Shipment Package The standard shipment package is provided with the following items. - SG300BT Handheld Bar code Scanner - Cradle or Charger - Power Adaptor (if applied) - Communication Cable - Skip resistant pad - Iron panel of cradle and screw - Quick Start Guide Visually inspect the device and accessories for any evidence of physical damage. If anything is missing or appears to be damaged, immediately contact your dealer. 2.2 Start Up Connect the communication cable provided to your POS or Host system and cradle. Power on the cradle with the provided power supply and scan the Bluetooth MAC address code located on the bottom of cradle. After approximately five seconds your connection is operational and the blue LED on the cradle is on., The scanner with Bluetooth must be charged for a minimum of 4.5 hours before it can be used. If the battery is full, the red light will be off. 2
6 2.3 User s Manual If you need the further information or more advanced setup options you can contact with your dealer or download the User s Manual on the service website. 3
7 3. Installation This device is very user friendly to be connected to your POS or Host system trough a RS232, Keyboard or USB cable. To read barcode, you simply press the trigger button and aim the beam to the barcode. You will hear one beep and the green LED indicator will light on after scan successfully. The configuration is very easy also you can setup the device by scanning all necessary programming codes from programming menu at a time to change the settings permanently. And all settings can be disabled after scan reset to factory default. 3.1 Environment Requirement Operation System: Win 98 / 2000 / XP / Vista Hardware Interface: RS232, KBW, USB II Power Supply: 5V DC 3.2 Cradle Installation to the Host Device Once you have unpacked all components, you can start installing the device into different steps. 4
8 RS232 Interface A. Turn off the host device. B. Connect the 10-pin RJ45 male connector into the 10-pin modular jack on the bottom of the cradle. C. Connect the 9-pin D-type Female connector of the RS232 cable to the proper COM port of the host device. D. Plug the external power supply into the power jack on the bottom of the cradle. E. Plug the power supply into the AC outlet. The red LED on the rear of the cradle will stay on. F. Turn on the host device 5
9 3.2.1 Keyboard Wedge Interface A. Turn off the host device. B. Connect the 10-pin RJ45 male connector into the 10-pin modular jack on the bottom of the cradle. C. Disconnect the keyboard from host. D. Connect the Y ends of the communication cable to the keyboard and keyboard port on the host device. If necessary, use the male/female adapter cable supplied with the scanner for the proper connections. E. Plug the external power supply into the power jack on the bottom of the cradle. F. Plug the power supply into the AC outlet. The red LED on the rear of the cradle will stay on. G. Turn on the host device. H. Establish communication between the scanner and cradle. 6
10 3.2.2 USB Interface A. Turn off the host device. B. Connect the 10-pin RJ45 male connector into the 10-pin modular jack on the bottom of the charger cradle. C. Connect the USB A type connector to the USB port on the host device. D. Plug the power supply into the power jack on the bottom of the cradle. E. Plug the power supply into the AC outlet. The red LED on the rear of the cradle will stay on. F. Turn on the host device. G. Establish communication between the scanner and cradle. 7
11 3.3 Cable installation Connect cable and adaptor to Cradle. The other end of cable will be connected with Host device. Lock the iron panel of Cradle by screwdriver 3.4 Skip resistant pad position 8
12 4. Program Sequence 4.1 Programming flow chart Start Configuration Recall Parameters* Set all Default Interface Selection* Communication Parameters Bar codes Parameters Misc. Parameters* etc. Abort Configurat ion* End Configurat ion Save Parameters 4.2 Factory Default Settings The SG300BT sets with the factory default setting when you start-up the SG300BT for the first time. The factory default settings are shown with <> and bold in the following sections. You can make your own settings by following the procedures in this guide. If you want to save the settings permanently, you should scan the programming code of Save Parameters otherwise the settings will not be saved 9
13 after the decoder power is off, and all settings will go back to previous settings. Default RS232 settings SG300BT: baud, no parity, 8 data bits, 1 stop bit. The following symbologies are factory default enabled UPC-A, UPC-E, EAN-8, EAN-13, Code 39, Code 128,Codabar and Interleaved 2 of 5. The chapters 4 to 6 provide you with the programming codes necessary for a basic setup. For more advanced setup options see SG300BT User s and Configuration Manual. 4.3 General Process Step 1 Power on the scanner. Step 2 Scan Start of Configuration Step 3 Scan the programming codes for the desired features before scan end. Step 4 Scan End of Configuration Step 5 Save The settings will be saved permanently 4.4 Set All Default Set all the parameters to the factory default setting. 10
14 4.5 Interface Keyboard Mode <RS232 Mode> USB Mode 11
15 5. RS232 Parameters 5.1 Baudrate Baudrate 4800 Baudrate 9600 <Baudrate 19200> Baudrate Parity <None> Even Odd Mark Space 12
16 5.3 Data bits Data bits 7 <Data bits 8> 5.4 Stop bits <Stop bits 1> Stop bits 2 6. Postambles 6.1 Postamble None <CR+LF> CR LF 13
17 7. Bluetooth Setup 7.1 Scanner Mode Client Mode ON / Server Mode OFF Server Mode ON / Client Mode OFF 7.2 Memory Mode Memory Mode ON Memory Mode <OFF> Memory Read Mode Memory Clear Mode 14
18 7.3 Sleep Mode <Sleep Mode On 1 minute> Sleep Mode On 10 minutes Sleep Mode OFF 15
19 8. Symbologies 8.1 Enable All Symbologies Enable all bar codes 8.2 Enable / Disable Symbologies UPC-A<ON> UPC-A OFF UPC-E<ON> UPC-E OFF EAN-13/JAN-13<ON> EAN-13/JAN-13 OFF EAN-8/JAN-8<ON> EAN-8/JAN-8 OFF CODE 39<ON> CODE 39 OFF 16
20 Code 128<ON> Code 128 OFF Interleave 2 of 5<ON> Interleave 2 of 5 OFF Codabar/NW7<ON> Codabar/NW7 OFF Industrial 2 of 5 ON Industrial 2 of 5<OFF> Matrix 2 of 5 ON Matrix 2 of 5<OFF> CODE 93 ON CODE 93<OFF> CODE 11 ON CODE 11<OFF> 17
21 MSI/PLESSEY ON MSI/PLESSEY <OFF> Telepen ON Telepen<OFF> China Postage ON China Postage<OFF> GS1 DataBar ON GS1 DataBar<OFF> GS1 DataBar Expanded ON GS1 DataBar Expanded<OFF> GS1 DataBar Limited ON GS1 DataBar Limited<OFF> ATTENTION: The following symbologies are factory default enabled; UPC-A, UPC-E, EAN-8, EAN-13, Code 39, Code 128, Codabar, Interleaved 18 2 of 5.
22 0145-SGB0021 V00 19
because we care MS910 Wireless Barcode Scanner Quick Guide Full user s manual is available on the enclosed CD. Version 1.2 400947G
because we care MS910 Wireless Barcode Scanner Quick Guide Full user s manual is available on the enclosed CD. Version 1.2 400947G because we care OUT OF THE BOX INTRODUCTION 2. Trigger 3. LED Indicator
More informationLaser Barcode Scanner User s Manual
Laser Barcode Scanner User s Manual FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
More informationMetrologic MS1690 2D Scanner Installation Guide
Metrologic MS1690 2D Scanner Installation Guide Revision 1.0 Revision History 1.0 04/17/2007 Initial Release The latest version of this document can be found in the following places: Internally for Cerner
More informationLaser Barcode Scanner
Laser Barcode Scanner User s Manual FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
More informationIntroduction. Setting Up the Scanner. Performing Verification Sequence
MDE-4389A Setting Up Datalogic DLL2020 Bar Code Scanner Used on Profit Point Terminal September 2005 Introduction If you have a Polaris bar code scanner, refer to C35424 Setting Up Your Polaris Bar Code
More informationBluetooth Version FUZZYSCAN FAMILY. Quick Start Guide WIRELESS SCANNER
Bluetooth Version FUZZYSCAN FAMILY Quick Start Guide WIRELESS SCANNER Getting Familiar with Your FuzzyScan Thank you for choosing Cino FuzzyScan Bluetooth Cordless Image Scanner. Powered by the combination
More informationQUICK START GUIDE Bluetooth Cordless Hand Scanner (CHS)
QUICK START GUIDE Bluetooth Cordless Hand Scanner (CHS) 1D Imager Models CHS 7Ci, 7Di, 7DiRx LED Trigger button Power button (also for ios Keyboard Pop-up) Model shown: CHS 7Di This document pertains to
More informationDUET / VS800 Scanner. DUET Scanner VS800 Scanner. Programming Kit
DUET / VS800 Scanner DUET Scanner VS800 Scanner Programming Kit PSC Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Telefax: (541) 345-7140 PSC and the PSC logo are registered
More informationSG20T. Tethered Scanner. User s Guide
SG20T Tethered Scanner User s Guide Intermec by Honeywell 6001 36th Ave.W. Everett, WA 98203 U.S.A. www.intermec.com The information contained herein is provided solely for the purpose of allowing customers
More informationOPR3301 USER MANUAL (OS version: RBJV0211 / Application version: RFJ35530)
CAUTION: This information is subject to change without prior notice. Copyright 2010, Opticon Sensors Europe BV, all rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced,
More informationScanner Configuration
Scanner Configuration SmartScan Manual DOC Version 2.21 This document is specifically designed for the user to print two pages per sheet of paper with optimal print quality. Copyright 2005~ 2008 CIPHERLAB
More informationWireless Laser Barcode Scanner ils 6300BU. User s Manual
Wireless Laser Barcode Scanner ils 6300BU User s Manual FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
More informationAll brand, product and service, and trademark names are the property of their registered owners.
Copyright 2010 EQUATOR LIMITED All rights reserved. All intellectual property rights are the property of their owners. EQUATOR LIMITED is authorized the right to use the software; it is provided under
More informationiloq P10S.10/20 Programming device User's Guide
iloq P10S.10/20 Programming device User's Guide CONTENTS CONTENTS... 2 GENERAL... 3 USING THE PROGRAMMING DEVICE... 5 Starting the programming device... 5 Programming of locks... 5 Programming of keys...
More informationHT580 User Reference Guide. Version 1.0
Version 1.0 NOTICE 1. Li-Ion Battery Pack The HT580 Portable Terminal and the Li-Ion Battery Pack are packaged separately. You will have to install the Battery Pack when you receive your terminal. Please
More informationVersaScan II. Barcode Scanner Quick Start Manual. ID TECH 10721 Walker Street Cypress, CA 90630 (714) 761-6368 www.idtechproducts.
VersaScan II TM Barcode Scanner Quick Start Manual ID TECH 10721 Walker Street Cypress, CA 90630 (714) 761-6368 www.idtechproducts.com 80105501-001 rev.a FCC WARNING STATEMENT This equipment has been tested
More informationKeep it Simple Timing
Keep it Simple Timing Support... 1 Introduction... 2 Turn On and Go... 3 Start Clock for Orienteering... 3 Pre Start Clock for Orienteering... 3 Real Time / Finish Clock... 3 Timer Clock... 4 Configuring
More informationBarcode Magstripe. Decoder & Scanner. Programming Manual
Barcode Magstripe Decoder & Scanner Programming Manual CONTENTS Getting Started... 2 Setup Procedures... 3 Setup Flow Chart...4 Group 0 : Interface Selection... 5 Group 1 : Device Selection for keyboard
More informationWireless Scanner. User s Manual - MS910 - Version 1.0
Wireless Scanner - MS910 - User s Manual Version 1.0 Table of Contents Chapter 1 Overview... 1 Introducing the MS910... 1 Package Contents... 2 Chapter 2 Installation and Connection... 5 Connecting (Pairing)
More informationBar Code CCD Scanner OPERATION MANUAL
ISO 9002 Certified Lead with technology Win customers with service Bar Code CCD Scanner OPERATION MANUAL 69 Jarltech International Inc. 1998. All rights reserved. Under the copyright laws, this manual
More informationGateKeeper: Barcode Scanner Setup. Rev. 20130410
GateKeeper: Barcode Scanner Setup Table of Contents I. Introduction...3 A. Why Use a Serial Interface Barcode Scanner?...3 B. Adding a Serial Port to your computer...3 C. GateKeeper and Member Check-In...3
More informationADDENDUM - Bluetooth interface Option Instructions for using Extech Printer with a Bluetooth device
Introduction ADDENDUM - Bluetooth interface Option Instructions for using Extech Printer with a Bluetooth device Extech 3500T and 2500T thermal printers support full range of communication interfaces,
More informationMS9500 SERIES VOYAGER PRODUCT GUIDE. Single Line, Hand-Held, 1D, High-Density 1D, PDF-417 2D and Wireless Laser Bar Code Scanners
MS9500 SERIES VOYAGER PRODUCT GUIDE Single Line, Hand-Held, 1D, High-Density 1D, PDF-417 2D and Wireless Laser Bar Code Scanners Contents About Voyager Scanners Voyager Selection Chart MS9520 Voyager MS9540
More informationQuick Installation. A Series of Intelligent Bar Code Reader with NeuroFuzzy Decoding. Quick Installation
Quick Installation A Series of Intelligent Bar Code Reader with NeuroFuzzy Decoding This chapter intends to get your new FuzzyScan scanner working with your existing system within minutes. General instructions
More informationMS830 / MS833 Barcode Reader v1.0 9-December-2014
MS830 / MS833 Barcode Reader v1.0 9-December-2014 Publication Information 2014 Imagine Communications Corp. Proprietary and Confidential. Imagine Communications considers this document and its contents
More informationSR30. Handheld Scanner. User s Guide
SR30 Handheld Scanner User s Guide Intermec Technologies Corporation Worldwide Headquarters 6001 36th Ave.W. Everett, WA 98203 U.S.A. www.intermec.com The information contained herein is provided solely
More informationBarcode Scanning Made Easy. WWS500 Programming Guide
Barcode Scanning Made Easy WWS500 Programming Guide Table of Contents Chapter 1. Introduction...........................2 Chapter 2. Barcode Symbologies...................3 Chapter 3. Quick Start............................4
More information[USING THE NM150 WITH ADULTICIDING] July 13, 2015
Reason Adulticiding 3.5 includes support for the New Mountain NM150 Weather Station. Adulticiding fogger log point details include temperature, wind speed, and wind direction. These can be recorded from
More informationSymbol MT2070 Scanner
Using the Symbol MT2070 Scanner for Inventory Copyright 2010 JMM Software, Inc. Taking Inventory with the Scanner 1) Wake up the scanner by squeezing the yellow trigger once. 2) If the copyright screen
More informationInstalling Your POS Hardware
Installing Your POS Hardware! Installing Your Barcode Scanner Remove the scanner from the packing materials. Attach the Y-cable to the scanner. Orient the connector on one end of the Y-cable so it has
More informationPM1122 INT DIGITAL INTERFACE REMOTE
PM1122 INT DIGITAL INTERFACE REMOTE PM1122 INT front panel description: 1. Clear wireless remotes knob: push this button for more than 2 seconds to clear the list of all assigned wireless remote settings
More informationVisionMate Flat Bed Scanner 2D Tube Barcode Reader
VisionMate Flat Bed Scanner 2D Tube Barcode Reader User s Manual Page 1 Catalog #3111 MAN-21256 Rev G Contact Information North America: Tel: 800.345.0206 email: matrix.info@thermofisher.com Europe: Tel:
More informationBARCODE READER V 2.1 EN USER MANUAL
BARCODE READER V 2.1 EN USER MANUAL INSTALLATION OF YOUR DEVICE PS-2 Connection RS-232 Connection (need 5Volts power supply) 1 INSTALLATION OF YOUR DEVICE USB Connection 2 USING THIS MANUAL TO SETUP YOUR
More informationSocket Bluetooth Cordless Hand Scanner (CHS) 7Xi and 7XiRx. 2D and 1D Barcode Scanners. User s Guide
Socket Bluetooth Cordless Hand Scanner (CHS) 7Xi and 7XiRx 2D and 1D Barcode Scanners User s Guide 1/2013 Document # 6410-00233 O COPYRIGHT NOTICE Copyright 2010-2013 Socket Mobile, Inc. All rights reserved.
More informationMODEL : LK-P31 MOBILE PRINTER
SEWOO TECH CO.,LTD. Doosung BD, 689-20, Geumjung-dong, Gunpo-si, Gyeonggi-do, 435-862 South Korea TEL : +82-31-459-8200 FAX : +82-31-459-8880 www.miniprinter.com MODEL : LK-P31 MOBILE PRINTER Rev. 1.0
More informationENGLISH USER S MANUAL. compact handheld 1D/2D code scanner
ENGLISH USER S MANUAL compact handheld 1D/D code scanner 11175-en-GB 5J006 04 006 1 3 A B 4 C INSTALLATION INSTRUCTIONS FIRST STEP: TURN POWER OFF! Exercise caution at all times when working with AC and
More informationDolphin 70e Black. Quick Start Guide. with Windows Embedded Handheld 6.5. 70E-WEH-QS Rev B 6/13
Dolphin 70e Black with Windows Embedded Handheld 6.5 Quick Start Guide 70E-WEH-QS Rev B 6/13 Out of the Box Verify that your carton contains the following items: Dolphin 70e Black mobile computer (terminal)
More informationQuickScan i. QD2100 Barcode Imager. Product Reference Guide
QuickScan i QD2100 Barcode Imager Product Reference Guide Configuring the Interface KEYBOARD FEATURES AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/standard Key Encoding Select KBD-AT Keyboard
More informationIndex...1. Introduction...3. Installation- Keyboard Wedge...3 RS-232...3 USB...3. Default Setting for each barcode shown as below:...
Index Index...1 Introduction...3 Installation- Keyboard Wedge...3 RS-232...3 USB...3 Default Setting for each barcode shown as below:...4 Programming the MS320...5 Interface Selection...7 Keyboard wedge...8
More information1560/1562 Barcode Scanner
1560/1562 Barcode Scanner Setup barcodes included. Version 1.13 Copyright 2009~2014 CIPHERLAB CO., LTD. All rights reserved The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided
More information1 Technical Description Lokal-200PC
1 Technical Description Lokal-200PC 1.1 Overview laptop with in-built accummulator USB connection correlator box internal power supply laptop (if the device has been supplied by F.A.S.T.) BNC aerial connection
More informationQuickScan Mobile. Reference Manual
QuickScan Mobile Reference Manual Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of
More informationTMCT-10 Barcode Scanner User Manual. 102, 5661-99 St. Edmonton, AB T6E 3N8 Ph. 780.988.0215 Fax 780.988.0465
TMCT-10 Barcode Scanner User Manual 102, 5661-99 St. Edmonton, AB T6E 3N8 Ph. 780.988.0215 Fax 780.988.0465 IMPORTANT NOTICE Safety Precaution * DO NOT disassemble the scanner, or place foreign matter
More informationMidland BT Updater BTUpdater Program Program file (x86) ), Midland
Midland BT Updater After you downloaded the BT Updater setup application from the web site, double click on it and follow the installation procedure. The BTUpdater application is automatically installed
More informationTable of Contents. 1. Overview... 3. 1.1 Materials Required. 3 1.2 System Requirements. 3 1.3 User Mode 3. 2. Installation Instructions..
Table of Contents 1. Overview..... 3 1.1 Materials Required. 3 1.2 System Requirements. 3 1.3 User Mode 3 2. Installation Instructions.. 4 2.1 Installing the On Call Diabetes Management Software. 4 2.2
More informationSerial to Bluetooth Adapter
Serial to Bluetooth Adapter Serial (RS-232) to Bluetooth Class 1 Adapter ICRS232BT1 Actual product may vary from photo FCC Compliance Statement This equipment has been tested and found to comply with the
More informationTable of Contents. GETTING STARTED...1 Technical Support...1 Scanner Configuration...2 Login and Select a Mode...4
Barcode Scanner Table of Contents GETTING STARTED...1 Technical Support...1 Scanner Configuration...2 Login and Select a Mode...4 USING THE SCANNER...7 Basic Functionality...7 Shipping or Receiving Mode...8
More informationPA700 Rugged Handheld Computer
PA700 Rugged Handheld Computer User s Manual Version 1.0 Table of content Table of content... 2 1. Package Contents... 3 2. Getting started... 4 2.1 Device overview... 4 2.2 Assembly... 6 Accessing battery,
More informationPart No. : MUL-53221-07 PROGRAMMING GUIDE
Part No. : MUL-53221-07 PROGRAMMING GUIDE PROGRAMMING GUIDE for BARCODE SCANNERS The guide can be used as keyboard emulation, RS- 232C serial interface, and USB 1.1 interface and wand emulation. IMPORTANT
More informationPP8X Printer Driver Installation Instruction
PP8X Printer Driver Installation Instruction Pinnacle Technology Corp. CONTENTS 1 BT Device Installation... 1 2 Printer Driver Installation... 6 3 How to Know the Connecting Port... 10 4 How to Configure
More informationBCST-20 Barcode Scanner. Instruction Manual. www.inateck.com
BCST-20 Barcode Scanner Instruction Manual www.inateck.com IMPORTANT NOTICE Safety Precaution * DO NOT disassemble the scanner, or place foreign matter into the scanner causing a short circuit or circuit
More informationOPN_DL UTILITY SOFTWARE. INSTALLATION AND USER GUIDE - v2.03
OPN_DL UTILITY SOFTWARE INSTALLATION AND USER GUIDE - v2.03 Electronic Reading Systems Ltd 14 Wolseley Business Park Kempston Beds MK42 7PW Tel: 01234 855300 Fax: 01234 855446 CONTENTS 1.0 INTRODUCTION
More informationS302D. Programming Guide. 2D Imaging Barcode Scanner. Advanced Handheld High-Speed Laser Scanner
S302D 2D Imaging Barcode Scanner Programming Guide 1 Advanced Handheld High-Speed Laser Scanner Revision History Changes to the original manual are listed below: Version Date Description of Version 1.0
More information2-Port RS232/422/485 Combo Serial to USB2.0 Adapter (w/ Metal Case and Screw Lock Mechanism) Installation Guide
2-Port RS232/422/485 Combo Serial to USB2.0 Adapter (w/ Metal Case and Screw Lock Mechanism) Installation Guide 1. Introduction Thank you for purchasing this 2-Port RS232/422/485 Combo Serial to USB Adapter.
More information16-Port RS232 to USB2.0 High Speed Multi Serial Adapter (w/ Metal Case) Installation Guide
16-Port RS232 to USB2.0 High Speed Multi Serial Adapter (w/ Metal Case) Installation Guide 1. Introduction Thank you for purchasing this 16-Port RS232 to USB2.0 High Speed Multi Serial Adapter. It is an
More informationProgramming and Using the Courier V.Everything Modem for Remote Operation of DDF6000
Programming and Using the Courier V.Everything Modem for Remote Operation of DDF6000 1.0 Introduction A Technical Application Note from Doppler System July 5, 1999 Version 3.x of the DDF6000, running version
More informationCT20 Barcode Scanner User Manual
CT20 Barcode Scanner User Manual IMPORTANT NOTICE Safety Precaution * DO NOT disassemble the scanner, or place foreign matter into the scanner cause a short circuit or circuit damage. * DO NOT expose the
More informationBarcode Scanner User Manual V6.6.2
Barcode Scanner User Manual V6.6.2 CONTENTS.......................................................................................... 1 1 2 2 3 4 13 14 15 17 17 19 19 20 22 23 23 28 29 33 42 60 65 85 87
More informationMK-SERIE 1000/1500/2000 AllOfBarcode.de Michael Krug - 83278Traunstein BARCODE SCANNER
MK-SERIE 1000/1500/2000 AllOfBarcode.de Michael Krug - 83278Traunstein BARCODE SCANNER Configuration Guide - 1 - Table of Contents Chapter 1 System Information 1.1 About this manual 3 1.2 How to set up
More informationBluetooth Serial Adapter
RN-BT-SRL-UM Bluetooth Serial Adapter 0 Roving Networks. All rights reserved. RN-BT-SRL-UM-.0 Version.0 //0 USER MANUAL RN-BT-SRL-UM-.0 OVERVIEW Roving Networks offers a variety of Bluetooth serial adapters
More informationLINĒA-PRO 4 iphone /ipod Touch 1D/2D SCANNER LINĒA-PRO 4 USER MANUAL
LINĒA-PRO 4 iphone /ipod Touch 1D/2D SCANNER LINĒA-PRO 4 CONTACT INFORMATION National Sales Headquarters: Infinite Peripherals, Inc. 1124 Main Street Suite B Irvine, CA 92614 Toll Free: (866) 278-7860
More informationPA500II Enterprise Mobile Computer
PA500II Enterprise Mobile Computer - PA500II - Quick Reference Guide 400891G Version 1.0 PA500II Product Introduction & Accessory Kit After opening the box, ensure the following accessories for the PA500II
More informationCS3000 SERIES SCANNER PRODUCT REFERENCE GUIDE
CS3000 SERIES SCANNER PRODUCT REFERENCE GUIDE CS3000 SERIES SCANNER PRODUCT REFERENCE GUIDE 72E-136088-04 Revision A February 2013 ii CS3000 Series Scanner Product Reference Guide 2013 Motorola Solutions,
More informationT3 Mux M13 Multiplexer
T3 Mux M13 Multiplexer User Manual [Type the abstract of the document here. The abstract is typically a short summary of the contents of the document. Type the abstract of the document here. The abstract
More informationINTEGRATION GUIDE. Bluetooth Connection Instructions for CR2300/CR2600/CR3600 VERSION 03 RELEASE DATE: MARCH 2016
INTEGRATION GUIDE Bluetooth Connection Instructions for CR2300/CR2600/CR3600 VERSION 03 RELEASE DATE: MARCH 2016 Apple is a trademarks of Apple Inc., registered in the U.S. and other countries. Windows
More informationSocket Bluetooth Cordless Hand Scanner (CHS) 1D Imager Models 7Ci, 7Di, 7DiRx. User s Guide
Socket Bluetooth Cordless Hand Scanner (CHS) 1D Imager Models 7Ci, 7Di, 7DiRx User s Guide 4/2014 Document# 6410-00343 C Copyright 2014 Socket Mobile, Inc. All rights reserved. COPYRIGHT NOTICE Socket,
More informationHow to setup a serial Bluetooth adapter Master Guide
How to setup a serial Bluetooth adapter Master Guide Nordfield.com Our serial Bluetooth adapters part UCBT232B and UCBT232EXA can be setup and paired using a Bluetooth management software called BlueSoleil
More informationAllen-Bradley. Bar Code. 2-D Hand-Held. Programming Guide. Bar Code. Scanners. (Cat. No. 2755-HTG-4)
Allen-Bradley 2-D Hand-Held Bar Code Scanners Bar Code Programming Guide (Cat. No. 2755-HTG-4) Important User Information The illustrations, charts, sample programs and layout examples shown in this guide
More informationBluetooth to Serial Adapter
Bluetooth to Serial Adapter Third Edition, Oct 2007 Version 3.0 771-BTS1009C3-001 Contents 1.0 Features....P.2 2.0 Package Content....P.2 3.0 Hard Drives Requirement.P.2 4.0 Specifications.P.3 5.0 Pin
More informationCD-3860 Bar Code Scanner User s Manual
CD-3860 Bar Code Scanner User s Manual Important Notice Rev. Original No warranty of any kind is made in regard to this material, including, but not limited to, implied warranties of merchantability or
More informationBaracoda RoadRunners. User Guide. This document is to be used with the Baracoda RoadRunners. Baracoda RoadRunners
User Guide Baracoda RoadRunners This document is to be used with the Baracoda RoadRunners Baracoda RoadRunners Package contents Check that you have the following items. Contact your reseller if any item
More informationChapter 1 Installing the Gateway
Chapter 1 Installing the Gateway This chapter describes how to set up the wireless voice gateway on your Local Area Network (LAN), connect to the Internet, and perform basic configuration. For information
More informationConnecting a Metrologic MS9535 to a USB BT Adapter (Client Mode)
Connecting a Metrologic MS9535 to a USB BT Adapter (Client Mode) I. Scope This document will provide a brief description of how to connect the Metrologic MS9535-5 scanner to a USB Bluetooth Adapter in
More informationInfinity C Reference Guide
1 2! Infinity C Reference Guide Table of Contents Components... 1 Hardware Setup... 5 SmartDrive Configuration... 12 Startup... 15 Login... 16 System Configuration... 19 DICOM Setup... 20 Monitoring Status...
More informationMS100 Bar Code Pen Reader
MS100 Bar Code Pen Reader AdventureJan General Advisory Improper handling, storage, environmental influences and /or product modification can lead to problems during use. This is particularly true if repairs
More informationUSER GUIDE. Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6
KRAMER ELECTRONICS LTD. USER GUIDE Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6 Contents 1 Connecting to the Kramer Device via the Ethernet Port 1 1.1 Connecting the Ethernet Port Directly
More informationUser s Manual. SR61 Cordless Scanner
User s Manual SR61 Cordless Scanner Intermec Technologies Corporation Worldwide Headquarters 6001 36th Ave.W. Everett, WA 98203 U.S.A. www.intermec.com The information contained herein is provided solely
More informationGryphon I GD44XX/GBT4400 General Purpose Handheld Area Imager Bar Code Reader
Gryphon I GD44XX/GBT4400 General Purpose Handheld Area Imager Bar Code Reader Product Reference Guide Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 USA Telephone: (541) 683-5700 Fax: (541)
More informationTo perform Ethernet setup and communication verification, first perform RS232 setup and communication verification:
PURPOSE Verify that communication is established for the following products programming option (488.2 compliant, SCPI only): DCS - M9C & DCS M130, DLM M9E & DLM-M9G & DLM M130, DHP - M9D, P series, SG,
More informationBI-300. Barcode configuration and commands Manual
BI-300 Barcode configuration and commands Manual 1. Introduction This instruction manual is designed to set-up bar code scanner particularly to optimize the function of BI-300 bar code scanner. Terminal
More informationXi2000 Series Configuration Guide
U.S. Default Settings Sequence Reset Scanner Xi2000 Series Configuration Guide Auto-Sense Mode ON UPC-A Convert to EAN-13 OFF UPC-E Lead Zero ON Save Changes POS-X, Inc. 2130 Grant St. Bellingham, WA 98225
More informationHP Point of Sale (POS) Peripherals Configuration Guide 2D Imaging / Linear / Presentation Scanner
HP Point of Sale (POS) Peripherals Configuration Guide 2D Imaging / Linear / Presentation Scanner Document Version 3.42 December 2011 1 Copyright 2007-2011 Hewlett-Packard Development Company, L.P. The
More informationSocketScan Software Advanced Programming Guide
SocketScan Software Advanced Programming Guide A guide to help you program symbology and parameter settings for the following Socket barcode scanning products: Secure Digital Scan Card Series 3 CompactFlash
More informationDVR-4TL/8TL/16TL Setup Guide
Package Content DVR-4TL/8TL/16TL Setup Guide Inspect the DVR s packaging. Make sure that the DVR-4TL/8TL/16TL is packed properly. Remove all items from the box and make sure it contains the following items.
More informationThank you for choosing the HUAWEI EC5805 Wireless Modem (E5).
Thank you for choosing the HUAWEI EC5805 Wireless Modem (E5). Note: Supported functions and actual appearance depend on the specific models you purchased. The following illustrations are provided for your
More informationQuick Installation Guide. Live! Titanium
Quick Installation Guide Live! Titanium Contents 1. Live! overview... 2. Installation... 3. Network setup... 4. Wireless setup... 5. Configuring your Live!... 6. Troubleshooting... 2 4 7 8 9 10 1 1. Live!
More informationDownload/Firmware upgrade instructions
Download/Firmware upgrade instructions Point of View 10 TAB-PROTAB30-IPS10-3G Preparation notice: Upgrading the firmware of your device may enhance the performance and functionality of your device. Incorrect
More information1166 / 1266 Barcode Scanner
1166 / 1266 Barcode Scanner Setup barcodes included. Version 3.03 Copyright 2005~2014 CIPHERLAB CO., LTD. All rights reserved The software contains proprietary information of CIPHERLAB CO., LTD.; it is
More informationTE100-P21/TEW-P21G Windows 7 Installation Instruction
Hardware Installation TE100-P21/TEW-P21G Windows 7 Installation Instruction 1. Go to http://www.trendnet.com/downloads/ to download the Windows 7 Utility. Save the file to your desktop. 2. Right click
More informationSTIM202 Evaluation Kit
Table of contents: 1 FEATURES... 2 2 GENERAL DESCRIPTIONS AND SYSTEM CONTENTS... 2 3 SYSTEM REQUIREMENTS... 2 4 GETTING STARTED... 3 4.1 INSTALLATION OF NI-SERIAL CABLE ASSEMBLY DRIVER... 3 4.2 INSTALLATION
More informationLCD Drawer User Manual
LCD Drawer User Manual - 1 - This manual, covering various aspects of the equipment such as installation, setup and installation, will help you make full use of this LCD KVM Drawer. Please read this manual
More informationGryphon Family General Purpose Handheld Linear Imager or Laser Bar Code Readers
Gryphon Family General Purpose Handheld Linear Imager or Laser Bar Code Readers Gryphon I GD4100/GM4100 Gryphon BT4100/ L GD4300 Product Reference Guide Datalogic Scanning, Inc. 959 Terry Street Eugene,
More informationSymbol CS3000 Series Scanner Product Reference Guide
Symbol CS3000 Series Scanner Product Reference Guide Symbol CS3000 Series Scanner Product Reference Guide 72E-136088-02 October 2010 ii Symbol CS3000 Series Scanner Product Reference Guide 2010 by Motorola,
More informationI-Suite Supply Module Standard Operating Procedures
I-Suite Supply Module Standard Operating Procedures 07/13/2013 Page 0 of 19 Table of Contents CTSP Responsibilities... 2 Supply Unit Responsibilities... 3 Appendix A... 5 Setting Up and Configuring Symbol
More informationConcert Hall Sound You Can Hold In Your. Hand. Users Manual 0.9
Concert Hall Sound You Can Hold In Your Hand Users Manual 0.9 1 Greetings Thank you for purchasing Calyx M. Calyx M is a product made for people who love music and want to listen no matter when or where
More information1. SAFETY INFORMATION
RS-232 Sound Level Meter 72-860A INSTRUCTION MANUAL www.tenma.com 1. SAFETY INFORMATION Read the following safety information carefully before attempting to operate or service the meter. Use the meter
More informationSection 5: Connecting the Laser to Your Computer
Section 5: Connecting the Laser to Your Computer In This Section Connecting the Laser to your Computer USB Port Ethernet Port Connecting the Laser to Your Computer All Epilog systems are designed to be
More informationUsing HyperTerminal with Agilent General Purpose Instruments
Using HyperTerminal with Agilent General Purpose Instruments Windows HyperTerminal can be used to program most General Purpose Instruments (not the 531xx series counters) using the RS-232 Serial Bus. Instrument
More informationOnline User s Guide RJ-3050/RJ-3150 RJ-3050 RJ-3150
Online User s Guide RJ-3050/RJ-3150 RJ-3050 RJ-3150 Before using this printer, be sure to read this Online User s Guide. We suggest you keep this manual in a safe place. Version 0 UK ENG Introduction Important
More informationUsing the Parani SD1000U/SD1000 with Carlson SurvCE
Using the Parani SD1000U/SD1000 with Carlson SurvCE Table of Contents Installing the Radio Driver...2 Pair the Radios...3 Connecting the Radio to the Total Station...4 Configuring SurvCE...5 Parts List...6
More information