SOIL MECHANICS Exam #3: Shear Strength.
|
|
- Ronald Sims
- 7 years ago
- Views:
Transcription
1 SOIL MECHANICS Exam #3: Shear Strength. Questions (2 Points Each - 20 Points Total): 1. Write the equation for the Mohr-Coulomb Failure Criteria for effective stresses in soils and detail the variables. f Where: f = Shear Stress at Failure ' = Effective Normal Stress ' = Effective Friction Angle c' = Effective Cohesion tan c 2. You have been given the results of a direct shear test on a well-graded sand (SW) sample. The Mohr-Coulomb effective stress failure criteria given to you from the test results are an effective friction angle of 33 degrees and an effective cohesion of 8.5 psi. Do you think these results are reasonable? Provide an explanation of your answer. ' = 33 is reasonable for sands. However, for sands c' 0. Therefore, a c' = 8.5 psi would not be reasonable. The soil may have been misclassified or the test was not run properly. 3. List the soil shear strength tests covered in class. Direct Shear Triaxial (CD, CU, UU) Unconfined Compression Exam 3 Solution Page 1 of 8
2 4. Write the equation for the Mohr-Coulomb Failure Criteria for total stresses in soils and detail the variables. Where: f = Shear Stress at Failure = Normal Stress '= Friction Angle c = Cohesion f tan c 5. You are given three soil samples. Soil Sample 1 is a silty sand. Soil Sample 2 is a fat clay. Soil Sample 3 is a lean clay. You are told to conduct the following triaxial tests on the samples: a slow test on Sample 1, a rapid test on Sample 2, and a quick test on Sample 3. What triaxial tests are you conducting on each sample? Provide the common test names and 2 letter abbreviations. Soil Sample 1 Slow Test = CD (Consolidated Drained) Soil Sample 2 Rapid Test = CU (Consolidated Undrained) Soil Sample 3 Quick Test = UU (Unconsolidated Undrained) 6. The direct shear test has been shown to be an effective test for determining the shear strength parameters (i.e. Mohr-Coulomb Failure Criteria) for coarse grained soils, especially sands. What is the major shortcoming of this test? The major shortcoming is the direct shear test forces the soil sample to fail along a fixed plane and not its preferred plane. 7. You have completed an unconfined compression test on a CL soil sample. The unconfined compression strength is 1120 psf. What is the undrained shear strength of this soil? S u = q u /2 = 1120 psf/2 = 560 psf. 8. Write the equation that relates unconfined compressive strength to undrained shear strength and detail the variables. S u = q u /2 Where: q u = Unconfined Compression Strength S u = Undrained Shear Strength Exam 3 Solution Page 2 of 8
3 9. Briefly describe soil sensitivity. Write any relevant equation(s) and detail the variables. Soil sensitivity is the ratio of undisturbed shear strength divided by disturbed shear strength. 10. Identify the relative density of the sands in the direct shear test results shown on Page 4. What is the major cause of the shear strength difference between the two samples if you are told that they are from the same soil deposit? Shear Stress Dilation is the difference! Dense Loose Volume Change Expansion Compression Shear Displacement Dense Shear Displacement Loose Exam 3 Solution Page 3 of 8
4 Problems: (1 25 points, 2-25 points, 3 15 points, 4 15 points, EC 5 Points) NOTICE: You must detail your answers (i.e. show your work) for these four problems for full credit. You must follow assignment guidelines for these problems. PROBLEM #1 GIVEN: Soil from a local contractors sand pit is proposed for use as backfill behind a retaining wall for a local project. The project specifications require that the backfill material have a minimum peak soil friction angle of 33 at the required minimum compaction (i.e. 90% Standard Proctor). The results from the direct shear testing performed at the minimum required compaction by a local testing firm are presented in Table 1: Soil Description: Silty Sand (SM). Table 1. Direct Shear Results conducted at 90% MMD (ASTM D698). Test Confining Stress ( ) (psf) Shear Stress ( ) (psf) Peak Residual REQUIRED & SOLUTION: Based on the provided information, answer the following: What are the peak and residual Mohr-Coulomb Failure Criteria this material? Peak = Residual MC Failure Criteria. ' = 30, c' = 250 psf (from Figure A). Does this material meet the project specifications regarding soil friction angle ( )? No, since residual = 30 < 33 required by project specifications Do you think this soil was tested in a loose or dense state? Briefly explain your answer. Soil was tested in a loose state since peak = residual Exam 3 Solution Page 4 of 8
5 3000 Shear Stress ( ) (psf) Peak & Residual: ' = 30, c' = 250 psf Best Fit Line ' = 30 c' = 250 psf Confining Stress (psf) Figure A. Shear Stress vs. Confining Stress Plot. PROBLEM #2 GIVEN: Soil from another local contractors sand pit is proposed for use as backfill behind a Mechanically Stabilized Earth (MSE) Wall for another local project. The project specifications require that the backfill material have a minimum residual soil friction angle of 34 at the required compaction (i.e. 95% Modified Proctor). Table 2 provides the results from the direct shear testing on this sample performed at the minimum required compaction by a local testing firm: Soil Description: Poorly Graded Sand (SP) Table 2. Direct Shear Results conducted at 95% MDD (ASTM D1557). Test Confining Stress ( ) (psf) Shear Stress ( ) (psf) Peak Residual Exam 3 Solution Page 5 of 8
6 REQUIRED & SOLUTION: Based on the provided information, answer the following: What are the peak and residual Mohr-Coulomb Failure Criteria for this material? Peak MC Failure Criteria: p ' = 38, c' = 0 psf (from Figure B). Residual MC Failure Criteria: r ' = 35, c' = 0 psf (from Figure B). Does this material meet the project specifications regarding soil friction angle ( )? Yes, since residual = 35 > 34 required by project specifications Do you think this soil was tested in a loose or dense state? Briefly explain your answer. Soil was tested in a dense state since peak > residual Shear Stress ( ) (psf) Peak: p ' = 38, c' = 0 psf Peak Best Fit Line Residual: r ' = 35, c' = 0 psf Residual Best Fit Line c' = 0 psf (SP) Confining Stress (psf) Figure B. Shear Stress vs. Confining Stress Plot Exam 3 Solution Page 6 of 8
7 PROBLEM #3 GIVEN: The results from three (3) Consolidated Undrained triaxial tests conducted on samples from a normally consolidated CL soil deposit are presented in Table 3. Table 3. CU Results on normally consolidated CL sample. Test Minor Principal Stress at Failure ( ' 3f ) (psi) Major Principal Stress at Failure ( ' 1f ) (psi) Pore Failure ( u df ) (psi) REQUIRED: Determine the Effective Stress Mohr-Coulomb Shear Strength Parameters (i.e. effective friction angle and effective cohesion) for this soil. SOLUTION: Effective Stress Mohr-Coulomb Envelope: ' = 30, c' = 0 psi. See Figure C. Shear Stress ( ) (psi) c' = 0 psi (NC Clay) Test 1 Test 2 Test 3 ' = 30 ' 3 ' 3 ' 3 ' 1f ' 1f ' 1f Confining Stress (psi) Figure C. Provided vs. Plot for Problem Exam 3 Solution Page 7 of 8
8 PROBLEM #4 GIVEN & REQUIRED: Using the CU test data provided in Problem 3, determine the Total Stress Mohr- Coulomb Shear Strength Parameters (i.e. friction angle and cohesion) for this soil. SOLUTION: Total Stress Mohr-Coulomb Envelope: = 24, c = 0 psi. See Figure C. Shear Stress ( ) (psi) c = 0 psi (NC Clay) Test 1 Test 2 Test 3 ' = 24 ' 3 ' 3 ' 3 ' 1f ' 1f ' 1f Confining Stress (psi) Figure D. Provided vs. Plot for Problem 4. EXTRA CREDIT (5 points): You are building a new embankment over cohesive soils. You need to determine the shear strength parameters to conduct slope stability and bearing capacity analyses at the end of construction (i.e. when the embankment is completed). What triaxial test(s) would you select to determine the shear strength parameters for these analyses? What would the shear strength parameter(s) be? UU Unconsolidated Undrained (i.e. Quick Test). Gives you Undrained Shear Strength (S u ) Exam 3 Solution Page 8 of 8
Drained and Undrained Conditions. Undrained and Drained Shear Strength
Drained and Undrained Conditions Undrained and Drained Shear Strength Lecture No. October, 00 Drained condition occurs when there is no change in pore water pressure due to external loading. In a drained
More informationSoil Mechanics. Outline. Shear Strength of Soils. Shear Failure Soil Strength. Laboratory Shear Strength Test. Stress Path Pore Pressure Parameters
Soil Mechanics Shear Strength of Soils Chih-Ping Lin National Chiao Tung Univ. cplin@mail.nctu.edu.tw 1 Outline Shear Failure Soil Strength Mohr-Coulomb Failure Criterion Laboratory Shear Strength Test
More informationSoil Strength. Performance Evaluation of Constructed Facilities Fall 2004. Prof. Mesut Pervizpour Office: KH #203 Ph: x4046
ENGR-627 Performance Evaluation of Constructed Facilities, Lecture # 4 Performance Evaluation of Constructed Facilities Fall 2004 Prof. Mesut Pervizpour Office: KH #203 Ph: x4046 1 Soil Strength 2 Soil
More informationc. Borehole Shear Test (BST): BST is performed according to the instructions published by Handy Geotechnical Instruments, Inc.
Design Manual Chapter 6 - Geotechnical 6B - Subsurface Exploration Program 6B-2 Testing A. General Information Several testing methods can be used to measure soil engineering properties. The advantages,
More informationSoil Mechanics SOIL STRENGTH page 1
Soil Mechanics SOIL STRENGTH page 1 Contents of this chapter : CHAPITRE 6. SOIL STRENGTH...1 6.1 PRINCIPAL PLANES AND PRINCIPAL STRESSES...1 6.2 MOHR CIRCLE...1 6.2.1 POLE METHOD OF FINDING STRESSES ON
More informationCEEN 162 - Geotechnical Engineering Laboratory Session 7 - Direct Shear and Unconfined Compression Tests
PURPOSE: The parameters of the shear strength relationship provide a means of evaluating the load carrying capacity of soils, stability of slopes, and pile capacity. The direct shear test is one of the
More informationSoil Mechanics. Soil Mechanics
Soil is the most misunderstood term in the field. The problem arises in the reasons for which different groups or professions study soils. Soil scientists are interested in soils as a medium for plant
More informationLABORATORY CLASSIFICATION OF SOILS FOR ENGINEERING PURPOSES
Test Procedure for LABORATORY CLASSIFICATION OF SOILS FOR ENGINEERING PURPOSES TxDOT Designation: Tex-142-E Effective Date: August 1999 1. SCOPE 1.1 This method is a system for classifying disturbed and
More informationINTRODUCTION TO SOIL MODULI. Jean-Louis BRIAUD 1
INTRODUCTION TO SOIL MODULI By Jean-Louis BRIAUD 1 The modulus of a soil is one of the most difficult soil parameters to estimate because it depends on so many factors. Therefore when one says for example:
More informationPART TWO GEOSYNTHETIC SOIL REINFORCEMENT. Martin Street Improvements, Fredonia, Wisconsin; Keystone Compac Hewnstone
GEOSYNTHETIC SOIL REINFORCEMENT Martin Street Improvements, Fredonia, Wisconsin; Keystone Compac Hewnstone DESIGN MANUAL & KEYWALL OPERATING GUIDE GEOSYNTHETIC SOIL REINFORCEMENT Keystone retaining walls
More information1 Mobilisation and demobilisation 1 Deep boring sum 2 Cone penetration tests sum 3 Miscellenous tests sum
Malaysian Civil Engineering Standard Method of Measurement (MyCESMM) CLASS D: SITE INVESTIGATION WORK Measurement covered under other classes: Excavation not carried out for the purpose of soil investigation
More informationSPECIFICATIONS FOR PRECAST MODULAR BLOCK RETAINING WALL SYSTEM (revised 11/5/13)
Page 1 of 7 STONE STRONG SYSTEMS SPECIFICATIONS FOR PRECAST MODULAR BLOCK RETAINING WALL SYSTEM (revised ) PART 1: GENERAL 1.01 Description A. Work includes furnishing and installing precast modular blocks
More informationSpecification Guidelines: Allan Block Modular Retaining Wall Systems
Specification Guidelines: Allan Block Modular Retaining Wall Systems The following specifications provide Allan Block Corporation's typical requirements and recommendations. At the engineer of record's
More informationCHAPTER 9 FEM MODELING OF SOIL-SHEET PILE WALL INTERACTION
391 CHAPTER 9 FEM MODELING OF SOIL-SHEET PILE WALL INTERACTION 9.1 OVERVIEW OF FE SOIL-STRUCTURE INTERACTION Clough and Denby (1969) introduced Finite Element analysis into the soil-structure interaction
More informationGEOTECHNICAL ENGINEERING FORMULAS. A handy reference for use in geotechnical analysis and design
GEOTECHNICAL ENGINEERING FORMULAS A handy reference for use in geotechnical analysis and design TABLE OF CONTENTS Page 1. SOIL CLASSIFICATION...3 1.1 USCS: Unified Soil Classification System...3 1.1.1
More informationFigure 2.31. CPT Equipment
Soil tests (1) In-situ test In order to sound the strength of the soils in Las Colinas Mountain, portable cone penetration tests (Japan Geotechnical Society, 1995) were performed at three points C1-C3
More informationDIRECT SHEAR TEST SOIL MECHANICS SOIL MECHANICS LABORATORY DEPARTMENT OF CIVIL ENGINEERING UNIVERSITY OF MORATUWA SRI LANKA
DIRECT SHEAR TEST SOIL MECHANICS SOIL MECHANICS LABORATORY DEPARTMENT OF CIVIL ENGINEERING UNIVERSITY OF MORATUWA SRI LANKA DIRECT SHEAR TEST OBJEVTIVES To determine the shear strength parameters for a
More information14.330 SOIL MECHANICS Assignment #4: Soil Permeability.
Geotechnical Engineering Research Laboratory One University Avenue Lowell, Massachusetts 01854 Edward L. Hajduk, D.Eng, PE Lecturer PA105D Tel: (978) 94 2621 Fax: (978) 94 052 e mail: Edward_Hajduk@uml.edu
More informationEM 1110-2-1902 31 Oct 2003. US Army Corps of Engineers ENGINEERING AND DESIGN. Slope Stability ENGINEER MANUAL
31 Oct 2003 US Army Corps of Engineers ENGINEERING AND DESIGN Slope Stability ENGINEER MANUAL AVAILABILITY Electronic copies of this and other U.S. Army Corps of Engineers (USACE) publications are available
More informationENCE 4610 Foundation Analysis and Design
This image cannot currently be displayed. ENCE 4610 Foundation Analysis and Design Shallow Foundations Total and Differential Settlement Schmertmann s Method This image cannot currently be displayed. Strength
More informationIngeniería y Georiesgos Ingeniería Geotécnica Car 19 a Nº 84-14 of 204 ; TEL : 6916043 E-mail: igr@ingeoriesgos.com
The plot below presents the cross correlation coeficient between the raw qc and fs values (as measured on the field). X axes presents the lag distance (one lag is the distance between two sucessive CPT
More informationEarth Pressure and Retaining Wall Basics for Non-Geotechnical Engineers
PDHonline Course C155 (2 PDH) Earth Pressure and Retaining Wall Basics for Non-Geotechnical Engineers Instructor: Richard P. Weber, P.E. 2012 PDH Online PDH Center 5272 Meadow Estates Drive Fairfax, VA
More informationKWANG SING ENGINEERING PTE LTD
KWANG SING ENGINEERING PTE LTD 1. INTRODUCTION This report represents the soil investigation works at Aljunied Road / Geylang East Central. The objective of the soil investigation is to obtain soil parameters
More information4.3 Results... 27 4.3.1 Drained Conditions... 27 4.3.2 Undrained Conditions... 28 4.4 References... 30 4.5 Data Files... 30 5 Undrained Analysis of
Table of Contents 1 One Dimensional Compression of a Finite Layer... 3 1.1 Problem Description... 3 1.1.1 Uniform Mesh... 3 1.1.2 Graded Mesh... 5 1.2 Analytical Solution... 6 1.3 Results... 6 1.3.1 Uniform
More informationNumerical Simulation of CPT Tip Resistance in Layered Soil
Numerical Simulation of CPT Tip Resistance in Layered Soil M.M. Ahmadi, Assistant Professor, mmahmadi@sharif.edu Dept. of Civil Engineering, Sharif University of Technology, Tehran, Iran Abstract The paper
More informationModule 7 (Lecture 24 to 28) RETAINING WALLS
Module 7 (Lecture 24 to 28) RETAINING WALLS Topics 24.1 INTRODUCTION 24.2 GRAVITY AND CANTILEVER WALLS 24.3 PROPORTIONING RETAINING WALLS 24.4 APPLICATION OF LATERAL EARTH PRESSURE THEORIES TO DESIGN 24.5
More informationSite Investigation. Some unsung heroes of Civil Engineering. buried right under your feet. 4. Need good knowledge of the soil conditions
This is an attempt to create a stand alone self learning module on site investigation. Fasten your seat belts. Sit back, relax and enjoy. 1 2 Site Investigation Some unsung heroes of Civil Engineering
More informationTable of Contents 10.1 GENERAL... 10.1-1
Table of Contents Section Page 10.1 GENERAL... 10.1-1 10.1.1 Overview... 10.1-1 10.1.2 Role of Uncertainty in Property Interpretation... 10.1-1 10.1.3 Role of Drainage in Property Interpretation... 10.1-2
More informationAbstract. Keywords. Pouya Salari 1, Gholam Reza Lashkaripour 2*, Mohammad Ghafoori 2. Email: * lashkaripour@um.ac.ir
Open Journal of Geology, 2015, 5, 231-2 Published Online May 2015 in SciRes. http://www.scirp.org/journal/ojg http://dx.doi.org/./ojg.2015.55021 Presentation of Empirical Equations for Estimating Internal
More informationModule 1 : Site Exploration and Geotechnical Investigation. Lecture 4 : In-situ tests [ Section 4.1: Penetrometer Tests ] Objectives
Lecture 4 : In-situ tests [ Section 4.1: Penetrometer Tests ] Objectives In this section you will learn the following Penetrometer Tests Standard penetration test Static cone penetration test Dynamic cone
More information1. ASTM C 140 - Sampling and Testing Concrete Masonry Units 2. ASTM C 1372 Standard Specification for Dry-Cast Segmental Retaining Wall Units
SPECIFICATION FOR SEGMENTAL RETAINING WALL SYSTEMS PART 1: GENERAL 1.01 Description A. Work shall consist of furnishing materials, labor, equipment and supervision to install a segmental retaining wall
More informationCE-632 Foundation Analysis and Design
CE-63 Foundation Analysis and Design Pile Foundations 1 Indian Standards on Piles IS 911 : Part 1 : Sec 1 : 1979 Driven cast in-situ concrete piles IS 911 : Part 1 : Sec : 1979 Bored cast-in-situ piles
More informationPeriod #16: Soil Compressibility and Consolidation (II)
Period #16: Soil Compressibility and Consolidation (II) A. Review and Motivation (1) Review: In most soils, changes in total volume are associated with reductions in void volume. The volume change of the
More informationproduct manual HS-4210 HS-4210_MAN_09.08 Digital Static Cone Penetrometer
HS-4210_MAN_09.08 product manual HS-4210 Digital Static Cone Penetrometer Introduction This Manual covers the measurement of bearing capacity using the Humboldt Digital Static Cone Penetrometer (DSCP).
More informationGEOTECHNICAL DESIGN MANUAL
GEOTECHNICAL DESIGN MANUAL CHAPTER 6 ENGINEERING PROPERTIES OF SOIL AND ROCK NYSDOT Geotechnical Page 6-1 June 17, 2013 (Intentionally left blank) NYSDOT Geotechnical Page 6-2 June 17, 2013 Table of Contents
More informationDams and Extreme Events Reducing Risk of Aging Infrastructure under Extreme Loading Conditions
Dams and Extreme Events Reducing Risk of Aging Infrastructure under Extreme Loading Conditions 34th Annual USSD Conference San Francisco, California, April 7-11, 2014 Hosted by San Francisco Public Utilities
More informationGEOTECHNICAL INVESTIGATION CITY OF HOUSTON SURFACE WATER TRANSMISSION PROGRAM CONTRACT 74A-1 WATERLINE COH WBS NO. S-000900-0109-3 HOUSTON, TEXAS
GEOTECHNICAL INVESTIGATION CITY OF HOUSTON SURFACE WATER TRANSMISSION PROGRAM CONTRACT 74A-1 WATERLINE COH WBS NO. S-000900-0109-3 HOUSTON, TEXAS Reported To: LAN, Inc. Houston, Texas by Aviles Engineering
More informationTECHNICAL SPECIFICATIONS CEMENT-BENTONITE SLURRY TRENCH CUTOFF WALL
TECHNICAL SPECIFICATIONS CEMENT-BENTONITE SLURRY TRENCH CUTOFF WALL SCOPE This section of the specifications includes requirements for the Slurry Trench Cutoff Wall and related work as indicated on the
More informationPILE FOUNDATIONS FM 5-134
C H A P T E R 6 PILE FOUNDATIONS Section I. GROUP BEHAVIOR 6-1. Group action. Piles are most effective when combined in groups or clusters. Combining piles in a group complicates analysis since the characteristics
More informationHIGHWAYS DEPARTMENT GUIDANCE NOTES ON SOIL TEST FOR PAVEMENT DESIGN
HIGHWAYS DEPARTMENT GUIDANCE NOTES ON SOIL TEST FOR PAVEMENT DESIGN Research & Development Division RD/GN/012 August 1990 HIGHWAYS DEPARTMENT GUIDANCE NOTES (RD/GN/012) SOIL TEST FOR PAVEMENT DESIGN Prepared
More information5/1/2013. Topics. The challenge is to better maintain native characteristics of soils during and after construction
PIN Foundations Topics Applications Design and Construction Flow Control Credits www.pinfoundations.com Copyright 2008, Pin Foundations, Inc. Curtis Hinman WSU Extension Faculty, Watershed Ecologist chinman@wsu.edu
More informationCone Penetration Testing (CPT) Michael Bailey, P.G. U.S. Army Corps of Engineers, Savannah District
Cone Penetration Testing (CPT) Michael Bailey, P.G. U.S. Army Corps of Engineers, Savannah District Recommended publications ASTM D 5778-07 Standard Test Method for Electronic Friction Cone and Piezocone
More informationSOUTH AFRICAN NATIONAL INSTITUTE OF ROCK MECHANICS CHAMBER OF MINES OF SOUTH AFRICA CERTIFICATE IN ROCK MECHANICS PART 1 ROCK MECHANICS THEORY
SOUTH AFRICAN NATIONAL INSTITUTE OF ROCK MECHANICS CHAMBER OF MINES OF SOUTH AFRICA CERTIFICATE IN ROCK MECHANICS PART 1 ROCK MECHANICS THEORY SYLLABUS Copyright 2006 SANIRE CONTENTS PREAMBLE... 3 TOPICS
More informationSystem. Stability. Security. Integrity. 150 Helical Anchor
Model 150 HELICAL ANCHOR System PN #MBHAT Stability. Security. Integrity. 150 Helical Anchor System About Foundation Supportworks is a network of the most experienced and knowledgeable foundation repair
More informationGUIDELINE FOR HAND HELD SHEAR VANE TEST
GUIDELINE FOR HAND HELD SHEAR VANE TEST NZ GEOTECHNICAL SOCIETY INC August 2001 CONTENTS Page 1.0 Introduction 2 2.0 Background 2 3.0 Recommended Practice 3 4.0 Undrained Shear Strength 3 5.0 Particular
More informationTests and Analyses on Shear Strength Increment of Soft Soil under Embankment Fill
Tests and Analyses on Shear Strength Increment of Soft Soil under Embankment Fill Guanbao Ye Professor Key Laboratory of Geotechnical and Underground Engineering,Tongji University, Ministry of Education,
More informationCOSMOS 2012: Earthquakes in Action COSMOS 2012
COSMOS 2012 What is SFSI and why is it important? Soil issues in Earthquakes Structures where SFSI important Retaining structures (lateral earth pressure) Foundations (spread and pile footings, bearing
More informationSPECIFICATION FOR DYNAMIC CONSOLIDATION / DYNAMIC REPLACEMENT
SPECIFICATION FOR DYNAMIC CONSOLIDATION / DYNAMIC REPLACEMENT 1.0 SOIL IMPROVEMENT 1.1 General Soil Investigation Information are provided in Part B1 annex as a guide to the Contractor for his consideration
More informationPVC PIPE PERFORMANCE FACTORS
PVC PIPE PERFORMANCE FACTORS PVC pipe, like all flexible pipe products, is very dependent on the surrounding soil for its structural capacity, in addition, the pipe material must have sufficient inherent
More informationGeotechnical Investigation using Standard Penetration Test (SPT) in Rangamati, Bandarban and Khagrachari Towns
1. Introduction 1.1 Scope of Work The Asian Disaster Preparedness Centre (ADPC) is implementing the project Seismic Hazard and Vulnerability Mapping for Rangamati, Bandarban and Khagrachari Municipality.
More informationGeotechnical Measurements and Explorations Prof. Nihar Ranjan Patra Department of Civil Engineering Indian Institute of Technology, Kanpur
Geotechnical Measurements and Explorations Prof. Nihar Ranjan Patra Department of Civil Engineering Indian Institute of Technology, Kanpur Lecture No. # 13 (Refer Slide Time: 00:18) So last class, it was
More informationGEOSYNTHETICS ENGINEERING: IN THEORY AND PRACTICE
GEOSYNTHETICS ENGINEERING: IN THEORY AND PRACTICE Prof. J. N. Mandal Department of civil engineering, IIT Bombay, Powai, Mumbai 400076, India. Tel.022-25767328 email: cejnm@civil.iitb.ac.in Module - 4
More informationload on the soil. For this article s examples, load bearing values given by the following table will be assumed.
How Many Piers? By Gary Collins, P.E. A clear-cut guide to helical pier spacing Introduction Helical pier spacing is not an exact science. How many does it take to support a structure adequately or repair
More informationSOIL COMPACTION BASICS
SOIL COMPACTION BASICS Figure courtesy of : A Basic Handbook by MultiQuip. : Densification of soil by the removal of air. Courtesy of http://www.extension.umn.edu Slide 1 of 38 WHY COMPACT SOILS? Figure
More informationCOMPENDIUM OF INDIAN STANDARDS ON SOIL ENGINEERING PART 2
(PREVIEW) SP 36 (Part 2) : 1988 COMPENDIUM OF INDIAN STANDARDS ON SOIL ENGINEERING PART 2 IS 1893 : 1979 (Reaffirmed 1987) CODE OF PRACTICE FOR SUBSURFACE INVESTIGATION FOR FOUNDATIONS 1.1 This code deals
More informationWashington 98102-3699, mike.bailey@hartcrowser.com
LESSONS LEARNED FROM A STONE COLUMN TEST PROGRAM IN GLACIAL DEPOSITS Barry S. Chen 1, P.E., Member, Geo-Institute and Michael J. Bailey 2, P.E., Member, Geo-Institute ABSTRACT A stone column test program
More informationCreep Characteristics and Shear Strength. of Recycled Asphalt Blends. Jeffery M. Schaper
Creep Characteristics and Shear Strength of Recycled Asphalt Blends by Jeffery M. Schaper A Thesis Presented in Partial Fulfillment of the Requirements for the Degree Master of Science Approved April 2011
More informationLiner system design for tailings impoundments and heap leach pads
Liner system design for tailings impoundments and heap leach pads John F. Lupo, Ph.D., P.E. AMEC E&E TAILINGS & MINE WASTE 08, VAIL Liner Systems Liner systems Environmental containment of process solutions
More informationvulcanhammer.net This document downloaded from
This document downloaded from vulcanhammer.net since 1997, your source for engineering information for the deep foundation and marine construction industries, and the historical site for Vulcan Iron Works
More informationUse and Application of Piezocone Penetration Testing in Presumpscot Formation
Use and Application of Piezocone Penetration Testing in Presumpscot Formation Craig W. Coolidge, P.E. Summit Geoengineering Services, Rockland, Maine ABSTRACT: This paper examines the advantages and limitations
More informationINTERNATIONAL JOURNAL OF CIVIL AND STRUCTURAL ENGINEERING Volume 3, No 3, 2013
INTERNATIONAL JOURNAL OF CIVIL AND STRUCTURAL ENGINEERING Volume 3, No 3, 2013 Copyright by the authors - Licensee IPA- Under Creative Commons license 3.0 Research article ISSN 0976 4399 Reliability of
More informationCIVL451. Soil Exploration and Characterization
CIVL451 Soil Exploration and Characterization 1 Definition The process of determining the layers of natural soil deposits that will underlie a proposed structure and their physical properties is generally
More informationSoil Classification Through Penetration Tests
Pak. J. Engg. & Appl. Sci. Vol. 9, Jul., 2011 (p. 76-86) Soil Classification Through Penetration Tests A. H. Khan, A. Akbar, K. Farooq, N. M. Khan, M. Aziz and H. Mujtaba Department of Civil Engineering,
More informationSIENA STONE GRAVITY RETAINING WALL INSTALLATION SPECIFICATIONS. Prepared by Risi Stone Systems Used by permission.
SIENA STONE GRAVITY RETAINING WALL INSTALLATION SPECIFICATIONS Prepared by Risi Stone Systems Used by permission. 1-800-UNILOCK www.unilock.com FOREWORD This outline specification has been prepared for
More informationFoundation Code compliance and Best Practices By Michael Coello
Foundation Code compliance and Best Practices By Michael Coello Background Graduated cum laude in 1992 with a Bachelor of Science degree in finance from University of Wisconsin - Parkside Started poured
More informationHow To Design A Foundation
The Islamic university - Gaza Faculty of Engineering Civil Engineering Department CHAPTER (2) SITE INVESTIGATION Instructor : Dr. Jehad Hamad Definition The process of determining the layers of natural
More informationGDS Triaxial Automated System (GDSTAS)
GDS Triaxial Automated System (GDSTAS) Overview: The GDS Triaxial Automated System (GDSTAS) is a load frame-based triaxial testing system. The system is configured by choosing from a range of load frames,
More informationANNEX D1 BASIC CONSIDERATIONS FOR REVIEWING STUDIES IN THE DETAILED RISK ASSESSMENT FOR SAFETY
ANNEX D1 BASIC CONSIDERATIONS FOR REVIEWING STUDIES IN THE DETAILED RISK ASSESSMENT FOR SAFETY ANNEX D1: BASIC CONSIDERATIONS FOR REVIEWING STUDIES IN DRA FOR SAFETY D1-1 ANNEX D1 BASIC CONSIDERATIONS
More informationCONSULTANCY & MATERIAL TESTING FACILITY
CONSULTANCY & MATERIAL TESTING FACILITY (CIVIL ENGINEERING DEPARTMENT) JAYPEE UNIVERSITY OF ENGINEERING & TECHNOLOGY A.B. ROAD, P.B. NO-1, RAGHOGARH, DIST: GUNA (M.P.) - 473226 Phone: 07544-267051, 267310-314,
More informationGround improvement using the vibro-stone column technique
Ground improvement using the vibro-stone column technique A. Kosho 1 A.L.T.E.A & Geostudio 2000, Durres, Albania ABSTRACT The vibro stone columns technique is one of the most used techniques for ground
More informationPullout Testing of Xgrid PET PVC 40/20 IT and Xgrid PET PVC 80/30 IT In Sand
Xgrid PET PVC 40 30 IT and PET PVC 80 30 IT in Sand - Pullout Testing Page 1 Pullout Testing of Xgrid PET PVC 40/20 IT and Xgrid PET PVC 80/30 IT In Sand February, 2006 Submitted to: TEMA Technologies
More informationModule 5 (Lectures 17 to 19) MAT FOUNDATIONS
Module 5 (Lectures 17 to 19) MAT FOUNDATIONS Topics 17.1 INTRODUCTION Rectangular Combined Footing: Trapezoidal Combined Footings: Cantilever Footing: Mat foundation: 17.2 COMMON TYPES OF MAT FOUNDATIONS
More informationSOILS AND FOUNDATIONS
CHAPTER 1 SOILS AND FOUNDATIONS SECTION 101 GENERAL 101.1 Scope. The provisions of this chapter shall apply to building and foundation systems in those areas not subject to scour or water pressure by wind
More informationWork Type Definition and Submittal Requirements
Work Type: Highway Materials Testing Geotechnical Laboratory Testing, Geotechnical Laboratory Testing, Standard Penetration (SPT) & Rock Coring, Cone Penetration Test, Solid Stem Auger Drilling, and Materials
More informationEffect of grain size, gradation and relative density on shear strength and dynamic cone penetration index of Mahi, Sabarmati and Vatrak Sand
Discovery ANALYSIS The International Daily journal ISSN 2278 5469 EISSN 2278 5450 2015 Discovery Publication. All Rights Reserved Effect of grain size, gradation and relative density on shear strength
More informationStrength Determination of "Tooth-Paste" Like Sand and Gravel Washing Fines Using DMT
Strength Determination of "Tooth-Paste" Like Sand and Gravel Washing Fines Using DMT David L. Knott, P.E. and James M. Sheahan, P.E. HDR Engineering, Inc. 3 Gateway Center Pittsburgh, PA 15222-1074 Phone:
More informationGeotechnical Characteristics of Two Different Soils and their Mixture and Relationships between Parameters
Geotechnical Characteristics of Two Different Soils and their Mixture and Relationships between Parameters Arpan Laskar Post Graduate Student Civil Engineering Department, National Institute of Technology
More informationDyanmic Cone. for Shallow
Dyanmic Cone for Shallow George F. Sowers' and Charles S. Hedge* REFERENCE: George F. Sowers and Charles S. Hedges, "Dynamic Cone for Shallow In-Situ Penetration Testing," Vane Shear and Cone Penetration
More informationIntroduction: Overview of Soil Mechanics
Introduction: Overview of Soil Mechanics 53:030 Soil Mechanics Notes; C.C. Swan, University of Iowa A. What is "soil"? 1) Not "dirt"! 2) Soil is unconsolidated earthen material comprised of discrete mineral
More informationK x ' Retaining. Walls ENCE 461. Foundation Analysis and Design. Mohr s Circle. and Lateral Earth. Pressures. Lateral Earth Pressure.
Lateral Earth Pressure Coefficient K x ' z ' K = lateral earth pressure coefficient x = horizontal effective stress Mohr s Circle and Lateral Earth Pressures x ' = = z ' ENCE 461 Foundation Analysis and
More informationMulti-stage Pseudo-static Analysis
Multi-stage Pseudo-static Analysis GEO-SLOPE International Ltd. www.geo-slope.com 14, 633-6th Ave SW, Calgary, AB, Canada T2P 2Y5 Main: +1 43 269 22 Fax: +1 43 266 4851 Introduction It is generally assumed
More information10.1 Powder mechanics
Fluid and Particulate systems 424514 /2014 POWDER MECHANICS & POWDER FLOW TESTING 10 Ron Zevenhoven ÅA Thermal and Flow Engineering ron.zevenhoven@abo.fi 10.1 Powder mechanics RoNz 2/38 Types of flow of
More informationTrench Rescue by Buddy Martinette
Trench Rescue by Buddy Martinette SOIL TYPE AND TESTING It is imperative that rescue personnel understand soil types and testing procedures if the want to be competent at trench rescue operations. Determining
More informationNumerical analysis of boundary conditions to tunnels
Global journal of multidisciplinary and applied sciences Available online at www.gjmas.com 2015 GJMAS Journal-2015-3-2/37-41 ISSN 2313-6685 2015 GJMAS Numerical analysis of boundary conditions to tunnels
More informationConsolidation and Settlement Analysis
19 Consolidation and Settlement Analysis Patrick J. Fox Purdue University 19.1 Components of Total Settlement 19.2 Immediate Settlement 19.3 Consolidation Settlement Total Consolidation Settlement Rate
More informationUNDER DRAINAGE AND FILTER DESIGN
UNDER DRAINAGE AND FILTER DESIGN Tailings and HLP Workshop 28 April to 1 May 2010 INTRODUCTION The internal drainage is of crucial importance to the reliability and safety of a tailings dam throughout
More informationA LABORATORY STUDY ON EFFECT OF TEST CONDITIONS ON SUBGRADE STRENGTH
A LABORATORY STUDY ON EFFECT OF TEST CONDITIONS ON SUBGRADE STRENGTH A REPORT SUBMITTED IN PARTIAL FULFILLMENT OF THE REQUIREMENTS FOR THE DEGREE OF Bachelor of Technology In Civil Engineering By: Rajesh
More informationBasic Soil Erosion and Types
Basic Soil Erosion and Types 2015 Wisconsin Lakes Convention Stacy Dehne DATCP Engineer Types of Soil Erosion Rain drop or splash erosion: Erosion preceded by the destruction of the crumb structure due
More informationChittagong Hill Tract Development Facilities (CHTDF) United Nations Development Programme
Chittagong Hill Tract Development Facilities (CHTDF) United Nations Development Programme Main Report Deliverable 02 Sub-Surface Properties of Soil Development in Rangamati, Bandarban and Khagrachari Municipality
More informationGEOTECHNICAL INVESTIGATION. Adelaide Street Pollution Control Plant Outlet Structure Replacement London, Ontario
September 2013 GEOTECHNICAL INVESTIGATION Adelaide Street Pollution Control Plant Outlet Structure Replacement London, Ontario Submitted to: Mr. Simon Jeater, C.Tech., Environmental Technician Stantec
More informationComprehensive Design Example 2: Foundations for Bulk Storage Facility
Comprehensive Design Example 2: Foundations for Bulk Storage Facility Problem The project consists of building several dry product storage silos near an existing rail siding in an open field presently
More informationSoil behaviour type from the CPT: an update
Soil behaviour type from the CPT: an update P.K. Robertson Gregg Drilling & Testing Inc., Signal Hill, California, USA ABSTRACT: An initial application of CPT results is to evaluate soil type and soil
More informationREINFORCED CONCRETE. Reinforced Concrete Design. A Fundamental Approach - Fifth Edition. Walls are generally used to provide lateral support for:
HANDOUT REINFORCED CONCRETE Reinforced Concrete Design A Fundamental Approach - Fifth Edition RETAINING WALLS Fifth Edition A. J. Clark School of Engineering Department of Civil and Environmental Engineering
More informationINDIRECT METHODS SOUNDING OR PENETRATION TESTS. Dr. K. M. Kouzer, Associate Professor in Civil Engineering, GEC Kozhikode
INDIRECT METHODS SOUNDING OR PENETRATION TESTS STANDARD PENETRATION TEST (SPT) Reference can be made to IS 2131 1981 for details on SPT. It is a field edtest to estimate e the penetration e resistance
More informationSlope Stability Analysis Using Finite Element Techniques
Slope Stability Analysis Using Finite Element Techniques Colby C. Swan, Assoc. Professor Young Kyo Seo, Post Doctoral Research Assoc. Civil & Environmental Engineering Center for Computer Aided Design
More informationDistribution Restriction Statement Approved for public release; distribution is unlimited.
CECW-ED Engineer Manual 1110-2-2504 Department of the Army U.S. Army Corps of Engineers Washington, DC 20314-1000 Engineering and Design DESIGN OF SHEET PILE WALLS EM 1110-2-2504 31 March 1994 Distribution
More informationDIRT DWELLING. and your. www.pinfoundations.com. Pin Foundations Inc., 2008
DIRT and your DWELLING 2008 Pin Foundations Inc., 2008 If we accept that preserving soil in its native condition is necessary, then how do we build? Utilities? Roads? Foundations? Typical Strip, Transfer,
More information2009 Japan-Russia Energy and Environment Dialogue in Niigata S2-6 TANAKA ERINA
Importance of the Site Investigation for Development of Methane Hydrate Hokkaido University Hiroyuki Tanaka Civil Engineer My Background Site Investigation Soil Parameters for Design Very Soft Clay and
More informationDETERMINATION OF SOIL STRENGTH CHARACTERISTICS PERFORMING THE PLATE BEARING TEST
III Międzynarodowa Konferencja Naukowo-Techniczna Nowoczesne technologie w budownictwie drogowym Poznań, 8 9 września 005 3rd International Conference Modern Technologies in Highway Engineering Poznań,
More informationSettlement of Precast Culverts Under High Fills; The Influence of Construction Sequence and Structural Effects of Longitudinal Strains
Settlement of Precast Culverts Under High Fills; The Influence of Construction Sequence and Structural Effects of Longitudinal Strains Doug Jenkins 1, Chris Lawson 2 1 Interactive Design Services, 2 Reinforced
More information