straight sliding bottom rolling door and gate hardware

Transcription

1 straight sliding rolling door and gate hardware section index and general guide Select system for your application. max. door Product data sheet Channel and profiles - actual size - and accessories APPLICATION - - C20 For frameless glass or solid panels on showcases, cabinets, etc. 16kg glassroll 16 C30 For timber doors to small cupboards 25kg timberoll 25 C40 For timber interior or exterior doors kg timberoll 80 & 170 C50 For timber interior or exterior doors 200kg timberoll 200 C60 For timber interior or exterior doors 270kg timberoll 270 C70 Residential Commercial Industrial data sheet C10

2

3 ProFiles For straight sliding rolling doors ProFiles actual size 25A 25DA 170A 171B 172B 272B A 402W A 901A 904A 904PA 906TA A B C a aluminium 402w aluminium aluminium 901 aluminium 403 aluminium 900a aluminium 906ta aluminium 904Pa aluminium and Polypropylene 170a aluminium 25da 171b bronze 25 aluminium 172 brass 272 brass data sheet C20

4 accessories 924 interlocker srip available in Clear or bronze anodised in 4.8m lengths. la250 available in Polished brass or satin Chrome. 456 Flush bolt 190 x 41 with 8 mortice and 20mm throw. available in satin nickel & PVd brass assa abloy new zealand ltd. Po box , north shore north shore City armstrong road, albany north shore City 0632 new zealand tel Fax data sheet C20b

5 glassroll 16 For sliding glass panels. max 16kg each. application Suitable for interior sliding frameless glass or panels of mirror, plastic, veneered timber, for showcases, bathroom cabinets, hatches and reception counter windows Double run system to suit bi-passing panels with s incorporating vertical adjustment and jump proof design Clean lines anodised aluminium with silent incorporating brushpile strips Panels can be secured by a specially designed cylinder lock Panel specification Rail System: Glassroll 16 For individual Panels: max Panel weight 16Kg max Panel area 1.0m² Panel thickness 6mm Panel sizing the panel height is 31mm less than the opening height. the panel width on bi-passing application is half the opening width plus 16mm. this provides a 38mm overlap at the centre of the opening when 406 end caps are fitted. Panels can be of glass, mirror, plastic, veneered timber etc but must be 6mm thick to accept the appropriate glazing strip. standard sets standard sets are available for bi-passing 6mm thick panels. sets comprise 402w with woolpile, two glazing s with 409 PVC glazing strip, 25da, four s, four end caps, two finger pulls, all screws and installation instructions. Set No. Opening Width gr mm for 2 panels gr mm for 2 panels gr mm for 2 panels hardware specification Top Guide, double run, with woolpile 402wa Top Guide, single run, no woolpile a Glazing Rail 403 Bottom Rail, double run 25da Bottom Rail, single run 25a material aluminium Finish satin anodised 3600mm Glazing Strip: 409 made for clear P.V.C to secure a 6mm panel in the glazing. available by the metre. Bottom Roller: 404 the nylon body incorporates a nylon wheel with a precision bearing for smooth operation. For high usage applications, or on panels near 16kg capacity, fit two s close together at each end of the glazing. End Cap: 406 the end cap is designed to hook onto the and is made from nylon. Finger Pull: 27C designed to fit into a 22mm diameter hole in the panel and is made from plastic with a satin chrome finish. Accessories: Cylinder Lock: 407 supplied with 2 keys and keyed alike or keyed to differ. available in left or right hand. Finish satin. no. no. 403 glazing no. 25a no. 402w no. 409 glazing strip no. 27 Finger Pull no. 404 no. 406 end Cap no. 25da data sheet C30

6 no. Glass Size for Double Passing Panels height = opening height less 31mm. width = half opening width plus 16mm. this provides a 38mm lap at centre. no. 402w glass 6 thick not to scale no. 27 Finger Pull installation instructions 1. Cut and to width of opening and fit in position using 12mm x 4g countersunk head wood screws. 2. Cut no. 403 glazing to width of glass. end must be perfectly square. 3. Fit glass to no. 403 glazing using glazing strip no. 409 for 6mm glass. trim off surplus. 4. insert the no. 404 s into ends of no. 403 glazing. hook no. 406 end Caps onto pins on the housing, (refer to note below, if fitting lock.) ensure that end Cap is hard against end of glazing. tighten screws in housing. 5. lift glass into and lower onto. 6. Fit no. 27 Finger Pull in Ø22mm hole in glass. no. 406 end Cap no. 409 glazing strip no. 25da no. 403 glazing no. 404 no. 25a no. 27 Finger Pull 38 overlap 2 Panels on 25da no. 507 Cylinder lock r.h. no. 27 Finger Pull no. 27 Finger Pull 38 overlap no. no lock lock r.h. 3 Panels on 25da & 25a s 38 overlap no. 27 Finger Pull no. 407 lock lock r.h. no. 27 Finger Pull Optional Extra no. 407 Cylinder lock, - with 2 keys. satin finish. state hand required (r.h. illustrated). when fitted lock replaces end Cap, refer note 4, above. tighten clamping screws. drill Ø8mm hole in inner glazing for lockpin, when panels are fitted. ensure that lock is of the correct hand and that glass overlaps by 38mm in centre. no. 407 lock lock r.h. r.h. 4 Panels on no. 25da no. 407 lock lock r.h. l.h. assa abloy new zealand ltd. Po box , north shore north shore City armstrong road, albany north shore City 0632 new zealand tel Fax data sheet C30b

7 timberoll 25 For sliding cupboard doors. max 25kg each. application Suitable for interior sliding timber doors to cupboards, wardrobes, bookcases, built-in furniture and other good quality cabinet work where a quiet, smooth action is required Any opening width may be accommodated and doors can slide on single or multiple lines of s door specification Rail System: Timberoll 25 For individual doors: max door weight 25kg max door width 900mm min door thickness 16mm timber framed glazed or flush doors or doors made from medium density fibreboard (mdf). it is essential that the of timber framed doors is of sufficient size to accommodate the s. standard sets standard sets are available for bi-passing or bi-parting doors. sets comprise two channels, two s, four s, four 25sFn s, all screws and installation instructions. Set No. Opening width tr mm for 2 doors tr mm for 2 doors tr mm for 2 doors hardware specification Top Guide Channel: 901 Bottom Rail: 25a material aluminium Finish mill 1200mm, 1500mm, 1800mm, 2400mm and 3600mm Top Guide: 3gn the s are made from nylon and are designed to fit into the top ends of each door and to slide in the 901 channel. Bottom Roller: 25sFn the is made with a stainless steel axle and a nylon wheel housed in a nylon body. the can either be mortised into the of the door or recessed into the back of the door. minimum door thickness 19mm. Alternative Hardware: Bottom Roller: 25san these s are designed only to be recessed in or surface mounted with or without 3mm vertical adjustment. they are made with a nylon wheel housed on a stainless steel plate. Accessories: Door Stop: 27ds the is made of nylon. on bi-passing doors one is fitted on the back face of the front door. 901 aluminium 27ds optional 25san 3gn supplied in sets 25sFn no. 25a data sheet C40

8 no. 901 wardrobe Channel 27 For top hung sliding wardrobe doors. max 27kg each no. 3gn not to scale not to scale typical door preparation for no. 25san. Cut,mortise into only, as far apart as possible. mortice shown allows to adjust 3mm up & 8.5mm to the right. typical door preparation for no. 25sFn. Cut,mortise into only, as far apart as possible. no. 25san no. 25a alternative no. 25sFn 5 x 5 groove full width of door no. 25a no. 25san no. 25sFn suitable for mortising into the of a door (minimum thickness 16) suitable for mortising into the of a door (minimum thickness 18) or recessing into the back of the door (minimum thickness 24) Finger Pull Finger Pull Finger Pull no. 27ds no. 27ds no. 27ds assa abloy new zealand ltd. Po box , north shore north shore City armstrong road, albany north shore City 0632 new zealand tel Fax data sheet C40b

9 timberoll 80 & 170 For sliding residential doors. max kg each. application For interior and exterior applications This quality hardware is ideally suited to premium joinery installations Designed for straight sliding partitions or fully glazed patio doors Also suitable for flush or panelled doors The design is suited to applications where the supporting structure or lintel is insufficient for the weight of the door or where headroom is limited To cover width of opening, any number of doors can be used on single or multiple lines of To accommodate different building designs, doors can slide to one or both sides Where doors are fitted externally, a canopy is recommended to protect the top guide channel, brackets and s door specification Rail System: Timberoll 80 & 170 For individual doors: max door height 2600mm max door weight 80 or 170kg min door thickness 35mm doors must be constructed with s of at least 150mm depth to accommodate the concealed, mortised, s. door weight is carried on the floor permitting the use of a light overhead structure. hardware specification Top Guide Tee: 906ta aluminium not recommended in situations where the door is likely to warp since the door could bind on the tee. the preferred option is the channel and s. Top Guide Channel: 904a aluminium 904b brass 904Pa aluminium and Polyprop 900 aluminium with safety lip 2000m, 3000mm, 4000mm and 6000mm Brackets: For single line - face fitted 1/250 stainless steel For double line - face fitted 5/180 stainless steel Fit at 900mm maximum centres. Top Guide Rollers (2 per door): top plate fitting single s/s 6g/904 bearing angle plate fitting single s/s 3g/904 bearing top plate fitting double 6g/900 nylon s one adjustable laterally to prevent rattle s/s Bottom Rollers (2 per door): 170sFb (170kg per door) 170sas (80kg per door) 170a/35, 36 or 38 (110kg per door) 30130b (100kg per door) 170sFb has brass with bearing in stainless steel body. 170sas has stainless steel, bearing and body. the has 10mm vertical adjustment. 170a has brass with bearing in zinc plated steel body b has nylon, carbon bearing and plastic body. has 10mm vertical adjustment. Bottom Rail: 171b bronze 172b brass 2000mm, 3000mm, 4000mm and 6000mm lengths. these s are drilled and countersunk for screwing to timber floor. Accessories: Flush bolts 456 or 456r sn, and PVdb Flush Pulls sn or PVdb s la250sc Frame seal aq21 brown or white 6g/900 top guide 3g/904 guide bz interlocker 6g/ b 170a/ a guide Channel 904Pa Channel 906ta 171b 172b la250sc 170sFb (170kg) 170sas (80kg) data sheet C50

10 904Pa Channel not to scale aq21 seal 3g/ ta tee 456 Flush bolt not to scale 170sas 900a Channel 6g/900 adjustable rattle Proof 170sas aq21 seal 171b 456 Keeper alternative sill with 23mm attached timber rebate not to scale 35, 36 or 38 height adjustment screw a/35-38 height adjustment screw 6 25 brass 172b 170sFb with brass wheel 172b 170sas end adjustable la250sc 171b 170sas back-to-back Flash Pulls bz inter locker no. 170a/35mm for aluminium doors 170a/36mm 170a/38mm 171b 170sas 456 Flush bolt 456 Flush Pull (above) 170sas back-to-back Flash Pulls 40 min. 50 max no b assa abloy new zealand ltd. Po box , north shore north shore City armstrong road, albany north shore City 0632 new zealand tel Fax data sheet C50b

11 timberoll 200 For sliding residential doors. max 200kg each. application For timber sliding doors interior and exterior applications Designed for straight sliding partitions or fully glazed patio doors. Also suitable for flush panelled doors The design is suited to applications where the supporting structure or lintel is insufficient for the weight of the door or where headroom is limited To cover the width of opening, any number of doors can be used on single or multiple lines or, doors can slide to one or both sides Where fitted externally, a canopy is recommended to protect the channel, brackets and s door specification Rail System: Timberoll 200 For individual doors: max leaf height 3000mm max leaf weight 200kg minimum door thickness 40mm doors must be constructed with s of at least 150mm depth to accommodate the concealed, mortised s. door weight is carried on the floor permitting the use of a light overhead structure. hardware specification Top Guide Tee: light duty 906ta aluminium not recommended in situations where the door is likely to warp since the door could bind on the tee. the preferred option is the channel and s. top tee guide is drilled and countersunk for direct fitting to soffit. Top Guide Channel: medium duty 904Pa aluminium support & Polypropylene heavy duty 900a aluminium with safety lip material mill aluminium Clear anodised 2000mm, 3000mm, 4000mm and 6000mm Bracket (Face Fix): For single line 1/250 For double line 5/180 Constructed from cast 316 stainless steel fit at 900mm maximum centres. Top Guide Rollers (2 per door): top plate fitting 6g/904 Corner fitting 3g/904 Cast 316 marine grade stainless with precision stainless steel bearings top plate fitting for 900 channel 6g/900 Cast 316 marine grade stainless plate with double nylon s with one adjustable laterally to prevent rattle. Bottom Rollers (2 per door): 170das Full stainless steel construction with precision stainless steel ball bearings wheels with side access vertical adjustment. Bottom Rail: 171b bronze 172b brass 2000mm, 3000mm, 4000mm and 6000mm drilled and countersunk. Interlocker: 924 aluminium anodised interlocker 4800mm to suit typical 2400mm door height Finishes Ca Clear and bz bronze drilled and countersunk, comes with brush seal Accessories: Flush bolts 456 or 456r sn and PVdb Flush Pulls sn or PVdb s la250sc Frame seal aq21 brown or white 6g/900 top guide 3g/904 guide Flush Pull 6g/ a guide Channel 906ta 904Pa Channel 171b bz interlocker la250sc 172b (optional) 170das data sheet C60

12 904Pa Channel aq21 seal 3g/ ta tee 456 Flush bolt not to scale 900a Channel 6g/900 adjustable, rattle proof not to scale 456 Keeper 170das aq21 seal 171b alternative sill with 23mm attached timber rebate not to scale height adjustment screw 170das side adjustable 171b 170das back-to-back Flash Pulls 171b 170das 456 Flush bolt Flush Pull (above) 170das back-to-back Flash Pulls assa abloy new zealand ltd. Po box , north shore north shore City armstrong road, albany north shore City 0632 new zealand tel Fax data sheet C60b

13 timberoll 270 For sliding residential doors. max 270kg each. application For interior and exterior applications This quality hardware is ideally suited to premium joinery installations Designed for heavy straight sliding partitions, fully glazed patio or showroom doors. also suitable for flush or panelled doors The design is suited to applications where the supporting structure or lintel is insufficient for the weight of the door or where headroom is limited To cover width of opening, any number of doors can be used on single or multiple lines of To accommodate different building designs, doors can slide to one or both sides Where doors are fitted externally, a canopy is recommended to protect the top guide channel, brackets and s door specification Rail System: Timberoll 270 For individual doors: max door height 3300mm max door weight 270kg min door thickness 44mm doors must be constructed with s of at least 175mm depth to accommodate the concealed, mortised, s. door weight is carried on the floor permitting the use of a light overhead structure. hardware specification Top Guide Channel: 900a material anodised aluminium 6000mm Top Guide Brackets: For single line - face fitted 1/250 stainless steel For double line - face fitted 5/180 stainless steel Fit at 900mm maximum centres. Top Guide Rollers (2 per door): 6g/900 s have double adjustable anti-rattle nylon s. steel components stainless steel. Bottom Rollers (2 per door): 270sFb 272sFb has brass with maintenance free bearing. body aluminium die casting. Bottom Rails: 272b 2000mm, 3000mm and 4000mm lengths. 272b is drilled and countersunk for screwing to timber floor or for attaching to lugs. Accessories: Flush bolts 456 or 456r sn and PVdb Flush Pulls sn or PVdb s la250sc Frame seal aq21 brown or white 1/250 bracket 924 interlock seal Flush Pull 270sFb 5/180 bracket 900a Channel 6g/ b la250sc data sheet C70

14 1/250 bracket m6 bolt with washer and Captive nut 900a Channel 6g/900 adjustable, rattle proof 1/250 bracket 5/180 bracket brush seal (by others) not to scale 270sFb single door with 6g/900 s in 900a Channel sill 272b rial brass, drilled and Countersunk 270sFb brass, ball Journal bearing 272b 270sFb back-to-back Flash Pulls bz inter locker 272b 270sFb 456 Flush bolt Flush Pull (above) 270sFb back-to-back Flash Pulls assa abloy new zealand ltd. Po box , north shore north shore City armstrong road, albany north shore City 0632 new zealand tel Fax data sheet C70b