2. The Laboratory Fume Hood Specification Catalog Select the style and size hoods appropriate for your layout and laboratory use.

Transcription

1

2 TABLE OF CONTENTS How to Specify... 3 Introduction to Fisher Hamilton Stainless Steel Laboratory Casework Stainless Steel Casework Options Menu... 6 Base Cabinets Sitting Height Cabinets... 8 Standing Height Cabinets Corner Base Cabinets Fume Hood Base Cabinets Sink Base Cabinets Acid/Flammable Storage Base Cabinets Mobile Base Cabinets Base Cabinet Accessories Fillers and Scribes Knee Space Panels/Rails Knee Space/Table Frames and Components End Support Panel Table Frame Assembly Wall Cases Wall Cases, 26-3/16" Height Wall Cases, 31" Height Wall Cases, 36-3/16" Height Filler Panels and Accessories Upper Cases Tall Cases Work Surfaces Performance Properties Build-A-Top Program How to Estimate Top without Curb Top with Curb Top with Scullery Sink and Curb Top with Scullery Sink, Curb and Ledge Standard Stainless Steel Scullery Sink Assemblies Epoxy Resin Work Surfaces Specifications Alphabetical Index Numerical Index Warranty Fisher Hamilton L.L.C. warrants to the direct purchaser that the products manufactured by it will be free from defects in material and workmanship for a period of one year from the date of installation. Fisher Hamilton will, at its sole option, either repair or replace any product during the warranty period which its examination reveals to have been defective, except that no warranty shall apply to accessories or parts or to any product which has been repaired by any party other than an authorized Fisher Hamilton Dealer. Fisher Hamilton shall have no obligation to repair or replace any product which has been subject to alteration, abuse, neglect or misuse or which has not been installed in strict conformity with the written instructions of Fisher Hamilton. Fisher Hamilton expressly disclaims all other warranties, express or implied, including the implied warranties of merchantability and fitness for a particular purpose. Under no circumstances whatsoever shall Fisher Hamilton be liable for any incidental or consequential damages, whether based on loss of goodwill, lost profits, or otherwise, and whether arising out of breach of any express or implied warranty, breach of contract, negligence, or otherwise, except in the case of personal injury as may be required by applicable state law. No employee, agent or representative of Fisher Hamilton, including, without limitation, any Fisher Hamilton Dealer, is authorized to bind Fisher Hamilton to any representation or warranty beyond that which is set forth above. All Fisher Hamilton products meet standards of the Scientific Equipment & Furniture Association (SEFA) and are designed exclusively to meet the needs of laboratories. For maximum ease and simplicity in planning a laboratory, you will need the following tools, available from your Fisher Hamilton dealer: 1. The Appropriate Project Planning Guide These guides provide step-by-step instructions for planning the optimum laboratory based on attributes of the physical space, budgetary considerations, usage patterns and other specific criteria. 2. The Laboratory Fume Hood Specification Catalog Select the style and size hoods appropriate for your layout and laboratory use. 3. The Fixtures and Accessories Specification Catalog Choose the size, style and material for sinks, fixtures, fittings and other accessories to make your laboratory complete. The Fisher Hamilton Literature Program Product Brochures Large photos provide an overall look and feel of each line. Photos and illustrations show basic components of each system, how they fit together, basic configurations and options. Features and benefits are clearly explained with close-up photography, cutaway drawings and exploded views. Product Specification Catalogs Catalogs encompass the complete product offering for each line. Intended as a reference tool in the planning stages, catalogs are also used for specification and ordering. Market Brochures Descriptions and photographs show how Fisher Hamilton products are applied within each specific market. Optimum product lines and options for specific markets are presented. Project Planning Guides Step-by-step workbook format facilitates organized, detailoriented lab planning. A Project Planning Guide has been produced specifically for each of the four major laboratory markets. Wood Steel Plastic Max/Lab Wood Steel Plastic Max/Lab Fix. & Access. Education K-12 Education K-12 C-Frame Education College- Univer. Education College- Univer. Industry Industry Healthcare Healthcare Fume Hoods Fume Hoods 2

3 IT S EASY TO SPECIFY FISHER HAMILTON STAINLESS STEEL Just follow these steps to design your ideal laboratory environment. 1. Review Introduction Review the quick introduction (See pages 3-6) to the Fisher Hamilton Stainless Steel laboratory furniture system. 2. Refer to Project Planning Guide Follow directions in the appropriate Planning Guide (i.e. Industrial) to develop the best lab solution for your needs. 3. Custom Assembly Components Select assemblies from pages 7-32 and specify by number and quanitity. 4. Options Choose from the Inset Steel Options Menu listed on Page 6 to apply to all furniture in your lab. 5. Fume Hoods Choose fume hoods that are appropriate for your layout and application from the Fisher Hamilton Fume Hood Product Specification Catalog. 7. Accessories Choose any accessories you need from the Hamilton Fixtures and Accessories Product Specification Catalog. 8. Work Surfaces Select work surfaces from pages to fit the assemblies you specify. 9. Service Fixtures Choose service fixtures for your furniture and fume hoods from the Fixtures and Accessories Product Specification Catalog. on the latest product information available at the time of publication. The right is reserved to make changes at any time without notice. 3

4 4 The right is reserved to make changes at any time without notice.

5 on the latest product information available at the time of publication. The right is reserved to make changes at any time without notice. 5

6 OPTIONS MENU Check here for all Standard Default selections. 7 Toe Space Soffit 1 Drawer Suspension 150 lb. fullextension drawer slides, zinccoated. Standard Default 100 lb. 3/4-extension, stainless steel. 150 lb. full-extension, stainless steel. 8 Label Holders None Standard Default Option 2 Hinges Stainless Steel with stainless steel screws Standard Default (No Option) None Standard Default Stainless Steel, one each door, one each drawer head (Option) Stainless Steel, one per pair of doors, one each drawer head (Option) 3 Pull Locations 9 Removable Access panel Horizontal on drawers, vertical on doors Standard Default (No Option) At cupboard areas only Standard Default At both cupboard & drawer areas (Option) 4 Pull Types 10 Glass Framed and/or Unframed Doors 5 Door Catches Stainless Steel Wire Finger Pull Standard Default (No Option) Roller Catch Standard Default 11 Security Panels between locked sections 6mm Clear Float Glass Standard Default 6mm Tempered Safety Glass (Option) 6mm Laminated Safety Glass (Option) 6 Lock Type Designated by Cabinet Suffix L Non-metallic Catch (Option) Without security panel Standard Default With security panel (Option) National Master 5-Disc (Remov-A-Core) Standard Default Use when up to 225 primary key changes are required National Master 5-Pin* Grand National Master 5-Pin* *Use when up to 2000 primary key changes are required, 8-week leadtime 6 The right is reserved to make changes at any time without notice.

7 Base Cabinets 18 Ga. uprights with holes for shelf clip attachment 18 Ga. rear access panels at cupboared unit Stainless steel shelf support clips, adjustable in 1/2" increments 20 Ga. adjustable shelf, shelves over 36" long have hat channel reinforcement 18 Ga. bottom Optional toespace suffit Hole for top attachment 18 Ga. toebase 18 Ga. sides and back, wrap-around construction 16 Ga. front rail (includes reinforced angle on cabinets over 30" wide) 14 Ga. front corner reinforcement (all four corners). All corners welded and ground smooth 16 Ga. intermediate front horizontal rail 18 Ga. divider post between drawers 18 Ga. upright with holes for attaching shelf clips. 14 Ga. case hinge reinforcement where hinges are located Access for leveling adjustment Hex head leveling screw for easy adjustment 11 Ga. gusset Steel Doors and Drawers: Doors are 20 gauge interior and 18 gauge exterior panels filled with sound deadening material, 14 Gauge steel reinforcement added at hinge locations and 20 Gauge vertical reinforcement channel, one each door. Nylon roller catch. When lock is supplied with double doors, elbow catch is used on left-hand door. Drawer heads are 20 gauge filled with sound deadening material. 20 Gauge one-piece drawer body with coved bottom. 14 Gauge drawer suspension with nylon-tired ball-bearing roller, has self-closing feature, fullextension telescoping drawer suspension is available. Stainless steel base cabinets by Fisher Hamilton are efficient and easy to use. Their modular design and durable construction provide remarkable loadbearing capacity, attractive appearance and long life. Available in a variety of styles and sizes to fit virtually any laboratory layout, these cabinets can be used in straightwall, corner and island configurations. Select from open, drawer, door and combination styles in standing or sitting heights as well as different widths. Refer to the appropriate Fisher Hamilton Project Planning Guide (Industrial, for example) for assistance in choosing the optimum components for your lab. Casework Fabrication Finish Standard All exposed surfaces shall ship with a No. 4 mill finish. All outer door and drawer fronts will ship with protective paper removed. All cabinet ends will ship with protective paper attached, unless specified as a regrained nonstandard option. Only areas being welded will have the protective paper removed (i.e. base cabinet bottoms). Cabinets will ship shrink-wrapped. on the latest product information available at the time of publication. The right is reserved to make changes at any time without notice. 7

8 BASE CABINETS BASE CABINETS SITTING HEIGHT 21-5/8" (54.9cm) Typical End View 29-3/8" (74.6cm) Common Features Shelves are adjustable in 1/2" (1.3 cm) increments. Standard without locks. Replace 0 with L in eighth position of product number to specify a unit with locks for drawers and doors. Lock and security panel options must be specified on the option menu - page 6. Removable back unless otherwise noted. Fume Hood Base Cabinet Flush panel above cupboard. Right- or left-hinged door. slide-out shelf in cupboard. With Right-Hinged Door 272B " (30.5cm) With Left-Hinged Door 273B " (30.5cm) Drawer Base Cabinets Two 4-1/2" (18.7cm) high drawers above one 10-1/4" (26.0cm) high file drawer. File drawer equipped with full extension slides. 139B B B " (45.7cm) 21" (53.3cm) 24" (61.0cm) Two 4-1/2" (18.7cm) high drawers above one 10-1/4" (26.0cm) high file drawer. File drawer equipped with full extension slides. With pullboard 130B B B " (45.7cm) 21" (53.3cm) 24" (61.0cm) Two 10-1/4" (26.0cm) high file drawers. File drawer equipped with full extension slides. 140B B B " (45.7cm) 21" (53.3cm) 24" (61.0cm) One 4-1/2" (18.7cm) high drawer above two 7-3/8" (18.7cm) high drawers. 142B B B B " (38.1cm) 18" (45.7cm) 21" (53.3cm) 24" (61.0cm) Note: For base cabinets, wall cases, upper cases and tall cases without finished bottoms, add suffix: Both ends finished = L (with lock) / J (no lock) R.H. end finished = K (with lock) / R (no lock) L.H. end finished = T (with lock) / F (no lock) Both ends unfinished = P (with lock) / U (no lock) 8

9 BASE CABINETS BASE CABINETS STANDING HEIGHT 21-5/8" (54.9cm) Typical End View 35-1/4" (89.5cm) Common Features Shelves are adjustable in 1/2" (1.3 cm) increments. Standard without locks. Replace 0 with L in eighth position of product number to specify a unit with locks for drawers and doors. Lock and security panel options must be specified on the option menu - page 6. Removable back unless otherwise noted. Open Door Base Cabinets Open door base cabinet. One adjustable shelf. 100B B B B B B B B8320 Swinging Door Base Cabinets Solid hinged full-height door. One adjustable shelf. 15" (38.1cm) 18" (45.7cm) 21" (53.3cm) 24" (61.0cm) 30" (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) Right Hinged Door 102B " (38.1cm) 102B " (45.7cm) 102B " (53.3cm) 102B " (61.0cm) Left Hinged Door (Shown) 103B " (38.1cm) 103B " (45.7cm) 103B " (53.3cm) 103B " (61.0cm) Solid hinged double doors. One adjustable shelf. 106B B B B8320 Sliding Door Base Cabinets 30" (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) Solid sliding double doors. One adjustable shelf. For locked doors, replace M with H in product number. 109B532M 109B632M 109B732M 109B832M 30" (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) Combination Base Cabinets One 4-1/2" (11.4cm) high drawer above cupboard. One adjustable shelf. Right Hinged Door 136B " (38.1cm) 136B " (45.7cm) 136B " (53.3cm) 136B " (61.0cm) Left Hinged Door (Shown) 137B " (38.1cm) 137B " (45.7cm) 137B " (53.3cm) 137B " (61.0cm) Two 1-5/8" (4.1cm) high drawers above cupboard. One adjustable shelf. Right Hinged Door 131B " (38.1 cm) 131B " (45.7 cm) 131B " (53.3 cm) 131B " (61.0 cm) Left Hinged Door (Shown) 132B " (38.1cm) 132B " (45.7cm) 132B " (53.3cm) 132B " (61.0cm) Two 4-1/2" (11.4cm) high drawers above cupboard. Double swinging doors. One adjustable shelf. 148B B B B " (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) Two 6" (15.2cm) high drawers above cupboard. Double swinging doors. One adjustable shelf. 257B B B B " (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) Note: For base cabinets, wall cases, upper cases and tall cases without finished bottoms, add suffix: Both ends finished = L (with lock) / J (no lock) R.H. end finished = K (with lock) / R (no lock) L.H. end finished = T (with lock) / F (no lock) Both ends unfinished = P (with lock) / U (no lock) 9

10 BASE CABINETS BASE CABINETS STANDING HEIGHT 21-5/8" (54.9cm) Typical End View 35-1/4" (89.5cm) Common Features Shelves are adjustable in 1/2" (1.3 cm) increments. Standard without locks. Replace 0 with L in eighth position of product number to specify a unit with locks for drawers and doors. Lock and security panel options must be specified on the option menu - page 6. Removable back unless otherwise noted. Combination Base Cabinets One full-width 4-1/2" (11.4cm) high drawer above cupboard. Double swinging doors. One adjustable shelf. 146B B B B " (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) Four 1-5/8" (4.1cm) high drawers above cupboard. Double swinging doors. One adjustable shelf. 179B B B B " (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) Two 4-1/2" (11.4cm) high drawers above two 7-3/8" (18.7cm) high drawers alongside full-height cupboard with swinging door. One adjustable shelf. Right Cupboard 180B " (76.2cm) 180B " (91.4cm) 180B " (106.7cm) 180B " (121.9cm) Left Cupboard (Shown) 181B " (76.2cm) 181B " (91.4cm) 181B " (106.7cm) 181B " (121.9cm) Combination Base Cabinets Four 6" (15.2cm) high drawers alongside one 6" (15.2cm) high drawer above cupboard with swinging door. One adjustable shelf. Right Cupboard 207B " (76.2cm) 207B " (91.4cm) 207B " (106.7cm) 207B " (121.9cm) Left Cupboard (Shown) 208B " (76.2cm) 208B " (91.4cm) 208B " (106.7cm) 208B " (121.9cm) Two 4-1/2" (11.4cm) high drawers above two 6" (15.2cm) high drawers anongside one 4-1/2" (11.4cm) high drawer above cupboard with righthinged door. One adjustable shelf. 177B B B B8320 Drawer Base Cabinets 30" (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) One 4-1/2" (18.7cm) high drawer above two 10-1/4" (26.0cm) high file drawers. File drawers equipped with full extension slides. With Removable Back 141B B B " (45.7cm) 21" (53.3cm) 24" (61.0cm) Note: For base cabinets, wall cases, upper cases and tall cases without finished bottoms, add suffix: Both ends finished = L (with lock) / J (no lock) R.H. end finished = K (with lock) / R (no lock) L.H. end finished = T (with lock) / F (no lock) Both ends unfinished = P (with lock) / U (no lock) 10

11 BASE CABINETS BASE CABINETS STANDING HEIGHT 21-5/8" (54.9cm) Typical End View 35-1/4" (89.5cm) Common Features Shelves are adjustable in 1/2" (1.3 cm) increments. Standard without locks. Replace 0 with L in eighth position of product number to specify a unit with locks for drawers and doors. Lock and security panel options must be specified on the option menu - page 6. Removable back unless otherwise noted. Drawer Base Cabinets Two 4-1/2" (18.7cm) high drawers above two 7-3/8" (18.7cm) high drawers. With pullboard. 186B " (61.0cm) Drawer Base Cabinets Three 4-1/2" (18.7cm) high drawers above one 10-1/4" (26.0cm) high file drawer. File drawer equipped with full extension slides. 170B B B " (45.7cm) 21" (53.3cm) 24" (61.0cm) Two 6" (15.2cm) high drawers above three full-width 6" (15.2cm) high drawers. 194B B B B " (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) Eight 6-1/2" (18.5cm) high drawers. Four 7-3/8" (18.7cm) high drawers. 173B " (38.1cm) 173B " (45.7cm) 173B " (53.3cm) 173B " (61.0cm) 206B B B B " (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) Two 1-5/8" (4.1cm) high drawers above one 4-1/2" (11.4cm) high drawer above two 7-3/8" (18.7cm) high drawers. 163B B B B " (38.1cm) 18" (45.7cm) 21" (53.3cm) 24" (61.0cm) Two 4-1/2" (18.7cm) high drawers above two 7-3/8" (18.7cm) high drawers. 164B B B B " (38.1cm) 18" (45.7cm) 21" (53.3cm) 24" (61.0cm) Two 4-1/2" (11.4cm) high full-width drawers above two 7-3/8" (18.7cm) high full-width drawers. 164B B B B " (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) Two 4-1/2" (11.4cm) high half-width drawers above one 4-1/2" (11.4cm) high and two 7-3/8" (18.7cm) high full-width drawers. 196B B B B " (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) Note: For base cabinets, wall cases, upper cases and tall cases without finished bottoms, add suffix: Both ends finished = L (with lock) / J (no lock) R.H. end finished = K (with lock) / R (no lock) L.H. end finished = T (with lock) / F (no lock) Both ends unfinished = P (with lock) / U (no lock) 11

12 BASE CABINETS BASE CABINETS STANDING HEIGHT 21-5/8" (54.9cm) Typical End View 35-1/4" (89.5cm) Common Features Shelves are adjustable in 1/2" (1.3 cm) increments. Standard without locks. Replace 0 with L in eighth position of product number to specify a unit with locks for drawers and doors. Lock and security panel options must be specified on the option menu - page 6. Removable back unless otherwise noted. Corner Base Cabinets Can be used as a sink cabinet. Right hinged swinging door only. See the Fisher Hamilton Fixtures & Accessories Catalog for sink supports. 422B /8" (83.5cm) Drawer Base Cabinets Four 4-1/2" (11.4cm) high drawers above two full-width 7-3/8" (18.7cm) high drawers. 200B B B B8320 Three 4-1/2" (11.4cm) high and two 1-5/8" (4.1cm) high half-width drawers above two 7-3/8" (18.7cm) high full-width drawers. 203B B B B " (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) Tour 4-1/2" (11.4cm) high half-width drawers above four 7-3/8" (18.7cm) high half-width drawers. 209B B B B B " (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) 24" (61.0cm) 30" (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) Equipped with three removable revolving shelves. Right hinged swinging door only. See the Fisher Hamilton Fixtures & Accessories Catalog for sink supports. 423B6320 WIDTH 18-1/8" (45cm) WIDTH 21-5/8" (54.9cm) 20-1/16" (50.9cm) 16" (40.6cm) TOP VIEW Fume Hood Base Cabinets 32-7/8" (83.5cm) Flush panel above cupboard. Right- or left-hinged door. Slide-out shelf in cupboard. 11-1/4" (28.4cm) With Right-Hinged Door 122B " (30.5cm) 122B " (61.0cm) With Left-Hinged Door 123B " (30.5cm) 123B " (61.0cm) Flush panel above solid hinged double doors. No shelf. Note: For base cabinets, wall cases, upper cases and tall cases without finished bottoms, add suffix: Both ends finished = L (with lock) / J (no lock) R.H. end finished = K (with lock) / R (no lock) L.H. end finished = T (with lock) / F (no lock) Both ends unfinished = P (with lock) / U (no lock) 121B B B B " (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) 12

13 BASE CABINETS BASE CABINETS STANDING HEIGHT 21-5/8" (54.9cm) Typical End View 35-1/4" (89.5cm) Sink Base Cabinets Common Features Shelves are adjustable in 1/2" (1.3 cm) increments. Standard without locks. Replace 0 with L in eighth position of product number to specify a unit with locks for drawers and doors. Lock and security panel options must be specified on the option menu - page 6. Removable back unless otherwise noted. Flush panel above solid hinged door. Back cut out for large sinks. Right Hinged Door 112B " (38.1cm) 112B " (45.7cm) 112B " (53.3cm) 112B " (61.0cm) Left Hinged Door (Shown) 113B " (38.1cm) 113B " (45.7cm) 113B " (53.3cm) 113B " (61.0cm) Flush panel above solid hinged double doors. Back cut out for large sinks. 115B B B B " (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) Flush panel above solid hinged double doors. Back cut out for large sinks. Toe space on exposed sides. 116B B " (132.1cm) 58" (147.3cm) Flush panel above solid hinged double doors. Back cut out for large sinks. 119B " (152.4cm) Resisto-Roc Lined Acid Storage Base Cabinets Ideal for use as fume hood base. Flush panel above solid hinged double doors. Adjustable shelf. Chemical resistant Resisto-Roc lining, 1/4" (6.4cm) thick. Vent cut out in back 10" (25.4cm) from right end. 144B B B B8320 Polyethylene Lined Acid Storage Base Cabinets Note: 30" (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) Full-height doors are lined with 1/8" (0.32cm) thick polyethylene. One half-depth shelf with polyethylene spill tray. Chemical resistant 3/16" (0.48cm) thick molded polyethylene lining with coved corners and 1" lip at front cabinet opening. Removable back panel. Two vent cut outs in cabinet back. 950B B " (91.4cm) 48" (121.9cm) Ideal for use as fume hood base. Flush panel above solid hinged double doors. Doors are lined with 1/8" (0.32cm) thick polyethylene. One half-depth shelf with polyethylene spill tray. Chemical resistant 3/16" (0.48cm) thick molded polyethylene lining with coved corners and 1" lip at front cabinet opening. Removable back panel. Two vent cut outs in cabinet back. 950B B B " (76.2cm) 36" (91.4cm) 48" (121.9cm) For base cabinets, wall cases, upper cases and tall cases without finished bottoms, add suffix: Both ends finished = L (with lock) / J (no lock) R.H. end finished = K (with lock) / R (no lock) L.H. end finished = T (with lock) / F (no lock) Both ends unfinished = P (with lock) / U (no lock) 13

14 BASE CABINETS STANDING HEIGHT/MOBILE BASE CABINET AND ACCESSORIES FOR BASE CABINETS Mobile Base Cabinets File Drawer Follower/Insert Assembly Two 4-1/2" (11.4cm) high drawers above one 10-1/4" (26.0cm) high file drawer. Drawers standard with locks and equipped with an integral locking device that allows operator to open only one drawer at a time. Heavy-duty locking double wheel 3" casters. Cabinet is equipped with anti-tipping counter weight. 950B096L 950B097L 18" (45.7 cm) 24" (61.0 cm) Add to cabinet file drawers. Material: cold-rolled steel. Color: Chameleon. Insert Cabinet 531B /8" 18" (35.9cm) (45.7cm) 531B /8" 21" (43.5cm) (53.3cm) 531B /8" 24" (51.1cm) (61.0cm) Add-On Shelf for Base Cabinets Includes four mounting clips per shelf. : 22" (55.9cm) Fits Cabinet Open and Swinging Door Cabinets 531B " (38.1 cm) 531B " (45.7 cm) 531B " (53.3 cm) 531B " (61.0 cm) 531B " (76.2 cm) 531B " (91.4 cm) 531B " (106.7 cm) 531B " (121.9 cm) Sliding Door Cabinets 531B " (76.2 cm) 531B " (91.4 cm) 531B " (106.7 cm) 531B " (121.9 cm) Note: For base cabinets, wall cases, upper cases and tall cases without finished bottoms, add suffix: Both ends finished = L (with lock) / J (no lock) R.H. end finished = K (with lock) / R (no lock) L.H. end finished = T (with lock) / F (no lock) Both ends unfinished = P (with lock) / U (no lock) 14

15 BASE CABINETS FILLERS AND COMPONENTS Filler Panels and Scribes for Base Cabinets End scribe for standing height base cabinet adjacent to wall. 600B B B B B2325 1" (2.5 cm) 2" (5.1 cm) 3" (7.6 cm) 4" (10.2 cm) 5" (12.7 cm) Rear filler panel for closing service space at rear of standing height base cabinet. 611B B B B B B /8" (18.7 cm) 10-3/8" (26.4 cm) 10-5/8" (27.0 cm) 12-1/8" (30.8 cm) 13-3/8" (34.0 cm) 19-3/8" (49.2 cm) Center filler panel for closing service space at back-to-back standing height base cabinets. 612B B B B /4" (22.2 cm) 14-3/4" (37.5 cm) 20-3/4" (52.7 cm) 26-3/4" (67.9 cm) Front filler for standing height base cabinets joined at a right angle. Adjustable up to 5" x 1" x 5" (12.7cm x 2.5cm x 12.7cm) in one direction. 607B B B0320 1" x 1" (2.5 cm) 2" x 2" (5.1 cm) 12" x 12" (30.5 cm) Knee Space Panel Knee Space Rail Leveling Tool Use at rear of knee space to provide physical and visual barrier. 616B B B B B B B B B " (61.0 cm) 30" (76.2 cm) 36" (91.4 cm) 42" (106.7 cm) 48" (121.9 cm) 54" (137.2 cm) 60" (152.4 cm) 66" (167.6 cm) 72" (182.9 cm) Use to close front knee space area between two cabinets. 4-1/2" high (11.4cm). 500B B B B B B B B B " (61.0 cm) 30" (76.2 cm) 36" (91.4 cm) 42" (106.7 cm) 48" (121.9 cm) 54" (137.2 cm) 60" (152.4 cm) 66" (167.6 cm) 72" (182.9 cm) For use with steel floor-mounted cabinets Fits through toe space access opening to rear leveling feet Relocates forward to capture front levelers 950M4000 Front filler panel for adjacent standing height base cabinets. 600B B B B B B B2320 6" (15.2 cm) 8" (20.3 cm) 10" (25.4 cm) 12" (30.5 cm) 14" (35.6 cm) 16" (40.6 cm) 18" (45.7 cm) Toe Kick Plate 950M4050 Replacement parts kit for leveling tool Kit contains: Chain (1), C Ring (2), Sprocket (2), Support, Sprocket (4), Socket (1), Handle ASM. (1) Stainless Steel toe kick plate covers the leveler access port on the front toe base of floor-mounted cabinets Attaches without tools 531B2400 One pair 15

16 BASE CABINETS KNEESPACE, TABLE FRAMES AND COMPONENTS Knee Space Drawer Frames End Support Panel 4-1/2" high frame with one standard drawer. Combination frame and drawer to use as table frame or to support a top suspended between two base cabinets or a base cabinet and a wall. : 21-1/2" (54.6cm) 501B " (61.0cm) 501B " (76.2cm) 501B " (91.4cm) : 28" (71.1cm) 501B " (61.0cm) 501B " (76.2cm) 501B " (91.4cm) 4-1/2" high frame with one large drawer. Combination frame and drawer to use as table frame or to support a top suspended between two base cabinets or a base cabinet and a wall. : 21-1/2" (54.6cm) 501B " (91.4cm) 501B " (106.7cm) 501B " (121.9cm) 501B " (137.2cm) 501B " (152.4cm) 4-1/2" high frame with two standard drawers. Combination frame and drawer to use as table frame or to support a top suspended between two base cabinets or a base cabinet and a wall. : 21-1/2" (54.6cm) 502B " (91.4cm) 502B " (106.7cm) 502B " (121.9cm) 502B " (137.2cm) : 28" (71.1cm) 502B " (91.4cm) 502B " (106.7cm) 502B " (121.9cm) 502B " (137.2cm) Use in place of legs on one end to support drawer frame. Attachment hardware included. Height : 21-1/2" (54.6cm) 525B " (73.7cm) 525B " (88.9cm) : 28" (71.1cm) 525B " (73.7cm) 525B " (88.9cm) Wall Bracket Leg Assemblies Use to support drawer frame cantilevered off a wall. Attachment hardware included. 526B1000 Single leg to provide support at either end of table frame. Connects to frame and wall. Adjustable levelers and vinyl leg shoes. Attachment hardware included. Height : 21-1/2" (54.6cm) 524B " (73.7cm) 524B " (88.9cm) : 28" (71.1cm) 524B " (73.7cm) 524B " (88.9cm) Double leg assembly with cross rail to provide support at either end of table frame. Adjustable levelers and vinyl leg shoes. Attachment hardware included. Height : 21-1/2" (54.6cm) 522B " (73.7cm) 522B " (88.9cm) : 28" (71.1cm) 522B " (73.7cm) 522B " (88.9cm) : 40" (101.6cm) 522B " (73.7cm) 522B " (88.9cm) : 46" (116.8cm) 522B " (73.7cm) 522B " (88.9cm) Double leg assembly with cross rail to provide support at center of table frames. Adjustable levelers and vinyl leg shoes. Attachment hardware included. Height : 21-1/2" (54.6cm) 523B " (73.7cm) 523B " (88.9cm) : 28" (71.1cm) 523B " (73.7cm) 523B " (88.9cm) : 40" (101.6cm) 523B " (73.7cm) 523B " (88.9cm) : 46" (116.8cm) 523B " (73.7cm) 523B " (88.9cm) 16

17 BASE CABINETS TABLE FRAMES AND COMPONENTS Table Frame Assembly Table frame assembly with adjustable levelers. Work surfaces ordered separately, see Work Surfaces Section in this catalog. Leg rails and leg stretchers ordered separately, see below. Height: 29" (73.3cm) : 28" (71.1cm) 950B B B3250 : 22" (55.9cm) 950B " (116.8cm) 58" (147.3cm) 70" (177.8cm) 52" (132.1cm) Table Leg Cross Rail Cross rails provide additional rigidity to table end legs. Attaching hardware included. 529B B B B B4600 of Leg Unit 22" (55.9cm) 28" (71.1cm) 34" (86.4cm) 40" (101.6cm) 46" (116.8cm) Table Leg Stretcher Leg stretcher provides stability between table legs. (Requires cross rail shown above). Attaching hardware included. 530B B B B3720 Fits Table 30" (76.2 cm) 42" (106.7 cm) 54" (137.2 cm) 66" (158.4 cm) Table Shelf Shelf provides extra storage beneath table top. Requires leg stretchers and leg cross rails (shown above). Attaching hardware included (61.0cm) 530B B B B " (76.2cm) 530B B B B8720 Table 36" (91.4cm) 48" (121.9cm) 60" (152.4cm) 72" (182.9cm) 36" (91.4cm) 48" (121.9cm) 60" (152.4cm) 72" (182.9cm) 17

18 18

19 Wall Cases Hanger angle 18 Ga. top 14 Ga. corner reinforcement (all four front corners). All corners welded and ground smooth Stainless steel shelf support clip Sturdy Fisher Hamilton wall cases are available in a wide range of sizes, ideal for your every storage requirement. They are designed for maximum storage capacity and easy access. These quality wall cases are available with sliding or swinging doors, or framed glass styles. Choose single or double doors or no doors at all. 20 Ga. shelf adjustable on 1/2" increments. Shelves over 36" long have hat channel reinforcement 18 Ga. upright. Additional 14 Ga. case hinge reinforcement at hinge locations 18 Ga. ends 18 Ga. upright with holes for shelf clips Refer to the appropriate Fisher Hamilton Project Planning Guide (Industrial, for example) for assistance in choosing the optimum components for your lab. 18 Ga. back 18 Ga. bottom 18 Ga. soffit bottom Steel Doors: Doors are 20 gauge interior and 18 gauge exterior panels filled with sound deadening material, 14 Gauge steel reinforcement added at hinge locations and 20 Gauge vertical reinforcement channel, one each door. Nylon roller catch. When lock is supplied with double doors, elbow catch is used on left-hand door. Casework Fabrication Finish Standard All exposed surfaces shall ship with a No. 4 mill finish. All outer door and drawer fronts will ship with protective paper removed. All cabinet ends will ship with protective paper attached, unless specified as a regrained nonstandard option. Only areas being welded will have the protective paper removed (i.e. base cabinet bottoms). Cabinets will ship shrink-wrapped. on the latest product information available at the time of publication. The right is reserved to make changes at any time without notice. 19

20 WALL CASES WALL CASES " HIGH Typical End View Open Wall Cases Common Features Wall cases include soffit bottoms. Shelves are adjustable in 1/2" (1.3 cm) increments. Wall cases have integral finished backs and fixed hanger rails hanger rails may be omitted on request. Standard without locks. Replace 0 with L in eighth position of product number to specify a unit with locks for doors. Lock option must be specified on the option menu. One adjustable shelf. 13" (33.0cm) 16" (40.6cm) 700B B " (38.1cm) 700B B " (45.7cm) 700B B " (53.3cm) 700B B " (61.0cm) 700B B " (76.2cm) 700B B " (91.4cm) 700B B " (106.7cm) 700B B " (121.9cm) Solid Swinging Door Wall Cases Note: DEPTH " (63.9cm) One adjustable shelf. For base cabinets, wall cases, upper cases and tall cases without finished bottoms, add suffix: Both ends finished = L (with lock) / J (no lock) R.H. end finished = K (with lock) / R (no lock) L.H. end finished = T (with lock) / F (no lock) Both ends unfinished = P (with lock) / U (no lock) 13" (33.0cm) 16" (40.6cm) Right-Hinged (Shown) 702B B " (38.1cm) 702B B " (45.7cm) 702B B " (53.3cm) 702B B " (61.0cm) Left-Hinged 703B B " (38.1cm) 703B B " (45.7cm) 703B B " (53.3cm) 703B B " (61.0cm) Double swinging doors with one adjustable shelf. 13" (33.0cm) 16" (40.6cm) 706B B " (76.2cm) 706B B " (91.4cm) 706B B " (106.7cm) 706B B " (121.9cm) Solid Sliding Door Wall Cases Double sliding doors with one adjustable shelf. 13" (33.0cm) 16" (40.6cm) Without Locks 715B523M 715B526M 30" (76.2 cm) 715B623M 715B626M 36" (91.4 cm) 715B723M 715B726M 42" (106.7 cm) 715B823M 715B826M 48" (121.9 cm) With Locks 715B523H 715B526H 30" (76.2 cm) 715B623H 715B626H 36" (91.4 cm) 715B723H 715B726H 42" (106.7 cm) 715B823H 715B826H 48" (121.9 cm) Framed Glass Swinging Door Wall Cases One adjustable shelf. 13" (33.0cm) 16" (40.6cm) Right-Hinged (Shown) 708B B " (38.1 cm) 708B B " (45.7 cm) 708B B " (53.3 cm) 708B B " (61.0 cm) Left-Hinged 709B B " (38.1 cm) 709B B " (45.7 cm) 709B B " (53.3 cm) 709B B " (61.0 cm) Double swinging doors with one adjustable shelf. 13" (33.0cm) 16" (40.6cm) 712B B " (76.2cm) 712B B " (91.4cm) 712B B " (106.7cm) 712B B " (121.9cm) Framed Glass Sliding Door Wall Cases Double sliding doors with one adjustable shelf. 13" (33.0cm) 16" (40.6cm) Without Locks 718B523M 718B526M 30" (76.2cm) 718B623M 718B626M 36" (91.4cm) 718B723M 718B726M 42" (106.7cm) 718B823M 718B826M 48" (121.9cm) With Locks 718B523H 718B526H 30" (76.4cm) 718B623H 718B626H 36" (91.4cm) 718B723H 718B726H 42" (106.7cm) 718B823H 718B826H 48" (121.9cm) 20

21 WALL CASES WALL CASES - 31" HIGH DEPTH Typical End View 31" (78.7cm) Common Features Wall cases include soffit bottoms. Shelves are adjustable in 1/2" (1.3 cm) increments. Wall cases have integral finished backs and fixed hanger rails hanger rails may be omitted on request. Standard without locks. Replace 0 with L in eighth position of product number to specify a unit with locks for doors. Lock option must be specified on the option menu. Solid Swinging Door Wall Cases Double swinging doors with two adjustable shelf. 13" (33.0cm) 16" (40.6cm) 706B B " (76.2cm) 706B B " (91.4cm) 706B B " (106.7cm) 706B B " (121.9cm) Open Wall Cases Two adjustable shelves. 13" (33.0cm) 16" (40.6cm) 700B B " (38.1cm) 700B B " (45.7cm) 700B B " (53.3cm) 700B B " (61.0cm) 700B B " (76.2cm) 700B B " (91.4cm) 700B B " (106.7cm) 700B B " (121.9cm) Solid Swinging Door Wall Cases Two adjustable shelf. 13" (33.0cm) 16" (40.6cm) Right-Hinged (Shown) 702B B " (38.1cm) 702B B " (45.7cm) 702B B " (53.3cm) 702B B " (61.0cm) Left-Hinged 703B B " (38.1cm) 703B B " (45.7cm) 703B B " (53.3cm) 703B B " (61.0cm) Solid Sliding Door Wall Cases Double sliding doors with two adjustable shelf. 13" (33.0cm) 16" (40.6cm) Without Locks 715B533M 715B536M 30" (76.2cm) 715B633M 715B636M 36" (91.4cm) 715B733M 715B736M 42" (106.7cm) 715B833M 715B836M 48" (121.9cm) With Locks 715B533H 715B536H 30" (76.2cm) 715B633H 715B636H 36" (91.4cm) 715B733H 715B736H 42" (106.7cm) 715B833H 715B836H 48" (121.9cm) Framed Glass Swinging Door Wall Cases Two adjustable shelves. 13" (33.0cm) 16" (40.6cm) Right-Hinged (Shown) 708B B " (38.1cm) 708B B " (45.7cm) 708B B " (53.3cm) 708B B " (61.0cm) Left-Hinged 709B B " (38.1cm) 709B B " (45.7cm) 709B B " (53.3cm) 709B B " (61.0cm) Double swinging doors with two adjustable shelves. Note: For base cabinets, wall cases, upper cases and tall cases without finished bottoms, add suffix: Both ends finished = L (with lock) / J (no lock) R.H. end finished = K (with lock) / R (no lock) L.H. end finished = T (with lock) / F (no lock) Both ends unfinished = P (with lock) / U (no lock) 13" (33.0cm) 16" (40.6cm) 712B B " (76.2cm) 712B B " (91.4cm) 712B B " (106.7cm) 712B B " (121.9cm) on the latest product information available at the time of publication. The right is reserved to make changes at any time without notice. 21

22 WALL CASES WALL CASES - 31" AND 36-13/16" HIGH DEPTH Typical End View 31" (78.7cm) Common Features Wall cases include soffit bottoms. Shelves are adjustable in 1/2" (1.3 cm) increments. Wall cases have integral finished backs and fixed hanger rails hanger rails may be omitted on request. Standard without locks (Except where noted). Replace 0 with L in eighth position of product number to specify a unit with locks for doors. Lock option must be specified on the option menu. DEPTH Typical End View 36-13/16" (94.5cm) Common Features Wall cases include soffit bottoms. Shelves are adjustable in 1/2" (1.3 cm) increments. Wall cases have integral finished backs and fixed hanger rails hanger rails may be omitted on request. Standard without locks. Replace 0 with L in eighth position of product number to specify a unit with locks for doors. Lock option must be specified on the option menu. Framed Glass Sliding Door Wall Cases Double sliding doors with two adjustable shelves. 13" (33.0cm) 16" (40.6cm) Without Locks 718B533M 718B536M 30" (76.2cm) 718B633M 718B636M 36" (91.4cm) 718B733M 718B736M 42" (106.7cm) 718B833M 718B836M 48" (121.9cm) With Locks 718B533H 718B536H 30" (76.2cm) 718B633H 718B636H 36" (91.4cm) 718B733H 718B736H 42" (106.7cm) 718B833H 718B836H 48" (121.9cm) Unframed Glass Sliding Door Wall Cases Double unframed glass sliding doors with two adjustable shelves. 13" (33.0cm) 16" (40.6cm) Without Lock 722B B " (76.2cm) 722B B " (91.4cm) 722B B " (106.7cm) 722B B " (121.9cm) With Lock 722B533L 722B536L 30" (76.2cm) 722B633L 722B636L 36" (91.4cm) 722B733L 722B736L 42" (106.7cm) 722B833L 722B836L 48" (121.9cm) Double unframed glass sliding doors on front and back side with two adjustable shelves. 13" (33.0cm) 16" (40.6cm) Without Lock 727B B " (76.2cm) 727B B " (91.4cm) 727B B " (106.7cm) 727B B " (121.9cm) With Lock 727B533L 727B536L 30" (76.2cm) 727B633L 727B636L 36" (91.4cm) 727B733L 727B736L 42" (106.7cm) 727B833L 727B836L 48" (121.9cm) Open Wall Cases Two adjustable shelves. 13" (33.0cm) 16" (40.6cm) 700B B " (38.1cm) 700B B " (45.7cm) 700B B " (53.3cm) 700B B " (61.0cm) 700B B " (76.2cm) 700B B " (91.4cm) 700B B " (106.7cm) 700B B " (121.9cm) Solid Swinging Door Wall Cases Note: Two adjustable shelves. For base cabinets, wall cases, upper cases and tall cases without finished bottoms, add suffix: Both ends finished = L (with lock) / J (no lock) R.H. end finished = K (with lock) / R (no lock) L.H. end finished = T (with lock) / F (no lock) Both ends unfinished = P (with lock) / U (no lock) 13" (33.0cm) 16" (40.6cm) Right-Hinged (Shown) 702B B " (38.1cm) 702B B " (45.7cm) 702B B " (53.3cm) 702B B " (61.0cm) Left-Hinged 703B B " (38.1cm) 703B B " (45.7cm) 703B B " (53.3cm) 703B B " (61.0cm) Double swinging doors with two adjustable shelves. 13" (33.0cm) 16" (40.6cm) 706B B " (76.2cm) 706B B " (91.4cm) 706B B " (106.7cm) 706B B " (121.9cm) 22

23 WALL CASES WALL CASES /16" HIGH DEPTH Typical End View 36-13/16" (94.5cm) Common Features Wall cases include soffit bottoms. Shelves are adjustable in 1/2" (1.3 cm) increments. Wall cases have integral finished backs and fixed hanger rails hanger rails may be omitted on request. Standard without locks (Except where noted). Replace 0 with L in eighth position of product number to specify a unit with locks for doors. Lock option must be specified on the option menu. Solid Sliding Door Wall Cases Double sliding doors with two adjustable shelves. 13" (33.0cm) 16" (40.6cm) Without Locks 715B553M 715B556M 30" (76.2cm) 715B653M 715B656M 36" (91.4cm) 715B753M 715B756M 42" (106.7cm) 715B853M 715B856M 48" (121.9cm) With Locks 715B553H 715B556H 30" (76.2cm) 715B653H 715B656H 36" (91.4cm) 715B753H 715B756H 42" (106.7cm) 715B853H 715B856H 48" (121.9cm) Framed Glass Swinging Door Wall Cases Two adjustable shelves. 13" (33.0cm) 16" (40.6cm) Right-Hinged (Shown) 708B B " (38.1cm) 708B B " (45.7cm) 708B B " (53.3cm) 708B B " (61.0cm) Left-Hinged 709B B " (38.1cm) 709B B " (45.7cm) 709B B " (53.3cm) 709B B " (61.0cm) Double swinging doors with two adjustable shelves. 13" (33.0cm) 16" (40.6cm) 712B B " (76.2cm) 712B B " (91.4cm) 712B B " (106.7cm) 712B B " (121.9cm) Framed Glass Sliding Door Wall Cases Double sliding doors with two adjustable shelves. 13" (33.0cm) 16" (40.6cm) Without Locks 718B553M 718B556M 30" (76.2cm) 718B653M 718B656M 36" (91.4cm) 718B753M 718B756M 42" (106.7cm) 718B853M 718B856M 48" (121.9cm) With Locks 718B553H 718B556H 30" (76.2cm) 718B653H 718B656H 36" (91.4cm) 718B753H 718B756H 42" (106.7cm) 718B853H 718B856H 48" (121.9cm) Unframed Glass Sliding Door Wall Cases Double unframed glass sliding doors with two adjustable shelves. 13" (33.0cm) 16" (40.6cm) Without Lock 722B B " (76.2cm) 722B B " (91.4cm) 722B B " (106.7cm) 722B B " (121.9cm) With Lock 722B553L 722B556L 30" (76.2cm) 722B653L 722B656L 36" (91.4cm) 722B753L 722B756L 42" (106.7cm) 722B853L 722B856L 48" (121.9cm) Add-On Shelf for Wall Cases Fits Cabinet For Solid and Framed Glass Sliding Door Cases 13" Deep 531B " (76.2 cm) 531B " (91.4 cm) 531B " (106.7 cm) 531B " (121.9 cm) 16" Deep 531B " (76.2 cm) 531B " (91.4 cm) 531B " (106.7 cm) 531B " (121.9 cm) Includes four mounting clips per shelf. Fits Cabinet For Open, Swinging Door and Unframed Glass Sliding Door Cases 13" Deep 531B " (38.1 cm) 531B " (45.7 cm) 531B " (53.3 cm) 531B " (61.0 cm) 531B " (76.2 cm) 531B " (91.4 cm) 531B " (106.7 cm) 531B " (121.9 cm) 16" Deep 531B " (38.1 cm) 531B " (45.7 cm) 531B " (53.3 cm) 531B " (61.0 cm) 531B " (76.2 cm) 531B " (91.4 cm) 531B " (106.7 cm) 531B " (121.9 cm) For base cabinets, upper cases and tall cases without finished bottoms, see Note on bottom of page 22. on the latest product information available at the time of publication. The right is reserved to make changes at any time without notice. 23

24 WALL CASES FILLERS AND SLOPING TOPS Filler Panels and Scribes Front filler panel for wall cabinet adjacent to wall or another wall cabinet. 13" (33.0cm) 16" (40.6cm) For Cases 25-3/16" (64.0cm) High 601B B2260 1" (2.5cm) 601B B4260 4"(10.2cm) 601B B5260 5"(12.7cm) 601B B6260 6"(15.2cm) 601B B8260 8"(20.3cm) 601B B "(25.4cm) 613B B "(30.5cm) 613B B "(35.6cm) 613B B "(40.6cm) 613B B "(45.7cm) For Cases 31" (78.7cm) High 601B B2360 1" (2.5 cm) 601B B4360 4"(10.2cm) 601B B5360 5"(12.7cm) 601B B6360 6"(15.2cm) 601B B8360 8"(20.3cm) 601B B "(25.4cm) 613B B "(30.5cm) 613B B "(35.6cm) 613B B "(40.6cm) 613B B "(45.7cm) For Cases 36-13/16" (93.5cm) High 601B B2560 1" (2.5 cm) 601B B4560 4"(10.2cm) 601B B5560 5"(12.7cm) 601B B6560 6"(15.2cm) 601B B8560 8"(20.3cm) 601B B "(25.4cm) 613B B "(30.5cm) 613B B "(35.6cm) 613B B "(40.6cm) 613B B "(45.7cm) Sloping Tops for Wall Cases Includes mounting hardware. For 13" Deep Cases 532B B B B B B B B B B B B B " Deep 533B B B B B B B B B B B B B1150 Fits Cabinet Includes mounting hardware. For 13" Deep Cases 531B " Deep 531B " (30.5cm) 15" (38.1cm) 18" (45.7cm) 21" (53.3cm) 24" (61.0cm) 30" (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) 60" (152.4cm) 72" (182.9cm) 84" (213.4cm) 96" (243.8cm) 12" (30.5cm) 15" (38.1cm) 18" (45.7cm) 21" (53.3cm) 24" (61.0cm) 30" (76.2cm) 36" (91.4cm) 42" (106.7cm) 48" (121.9cm) 60" (152.4cm) 72" (182.9cm) 84" (213.4cm) 96" (243.8cm) Front corner filler for wall cabinets joined at a right angle. 13" (33.0cm) 16" (40.6cm) For Cases 25-3/16" (64.0cm) High 608B B1260 1" x 1" (2.5cm) 608B B2260 2" x 2" (5.1cm) For Cases 31" (78.7cm) High 608B B1360 1" x 1" (2.5cm) 608B B2360 2" x 2" (5.1cm) For Cases 36-13/16" (93.5cm) High 608B B1560 1" x 1" (2.5cm) 608B B2560 2" x 2" (5.1cm) 24

25 Upper Cabinets Hanger angle 20 Ga. shelf adjustable on 1/2" increments. Shelves over 36" long have hat channel reinforcement 18 Ga. top 14 Ga. corner reinforcement (all four front corners). All corners welded and ground smooth Stainless steel shelf support clip 18 Ga. upright. Additional 14 Ga. case hinge reinforcement at hinge locations 18 Ga. ends 18 Ga. upright with holes for shelf clips Upper cabinets by Fisher Hamilton enhance the flexibility of your lab and provide attractive, spacious storage with convenient user access. Designed for placement directly on base cabinet work surfaces, the standard upper case height matches to the top of wall cases or tall cases when placed on a standing-height base cabinet. Select from open front units or cases with sliding or swinging doors, or framed glass. Refer to the appropriate Fisher Hamilton Project Planning Guide (Industrial, for example) for assistance in choosing the optimum components for your lab. 18 Ga. back 18 Ga. bottom Steel Doors: Doors are 20 gauge interior and 18 gauge exterior panels filled with sound deadening material, 14 Gauge steel reinforcement added at hinge locations and 20 Gauge vertical reinforcement channel, one each door. Nylon roller catch. When lock is supplied with double doors, elbow catch is used on left-hand door. Casework Fabrication Finish Standard All exposed surfaces shall ship with a No. 4 mill finish. All outer door and drawer fronts will ship with protective paper removed. All cabinet ends will ship with protective paper attached, unless specified as a regrained nonstandard option. Only areas being welded will have the protective paper removed (i.e. base cabinet bottoms). Cabinets will ship shrink-wrapped. on the latest product information available at the time of publication. The right is reserved to make changes at any time without notice. 25

26 UPPER CASES UPPER CASES 49-13/32" HIGH DEPTH 49-13/32" (125.4cm) Typical End View Common Features Upper cabinets have three shelves adjustable in 1/2" (1.3 cm) increments. Shelf s: 10-1/4" (26.0cm) and 13-1/4 (33.7cm) in open and swinging door cases; 9-1/2" (24.1cm) and 12-1/2 (31.8cm) in sliding door cases. NOTE; Suffix for product numbers are as follows (Replace 0 in eighth position of product number). Lock must be specified on the option menu: 0 = Unfinished bottoms (open cases) B = Finished bottoms (open cases) 0 = Without lock, unfinished bottoms (hinged doors) L = With lock, unfinished bottoms (hinged doors) B = Without lock, finished bottoms (hinged doors) D = With lock, Finished bottoms (hinged doors) M = Without lock, unfinished bottoms (sliding doors) H = With lock, unfinished bottoms (hinged doors) B = Without lock, finished bottoms (hinged doors) D = With lock, Finished bottoms (sliding doors) Solid Sliding Door Cabinets Double solid sliding doors. Three adjustable shelves. 13" (33.0cm) 16" (40.6cm) Without Locked Doors 715B563M 715B566M 30" (76.2cm) 715B663M 715B666M 36" (91.4cm) 715B763M 715B766M 42" (106.7cm) 715B863M 715B866M 48" (121.9cm) With Locked Doors 715B563H 715B566H 30" (76.2cm) 715B663H 715B666H 36" (91.4cm) 715B763H 715B766H 42" (106.7cm) 715B863H 715B866H 48" (121.9cm) Framed Glass Swinging Door Upper Cases Double framed glass swinging doors. Three adjustable shelves. Open Door Upper Cases Three adjustable shelves. Solid Swinging Door Cabinets 13" (33.0cm) 16" (40.6cm) 700B B " (45.7cm) 700B B " (61.0cm) 700B B " (76.2cm) 700B B " (91.4cm) 700B B " (106.7cm) 700B B " (121.9cm) Double solid swinging doors. Three adjustable shelves. 13" (33.0cm) 16" (40.6cm) 706B B " (76.2cm) 706B B " (91.4cm) 706B B " (106.7cm) 706B B " (121.9cm) 13" (33.0cm) 16" (40.6cm) 712B B " (76.2cm) 712B B " (91.4cm) 712B B " (106.7cm) 712B B " (121.9cm) Framed Glass Sliding Door Upper Cases Double framed glass sliding doors. Three adjustable shelves. 13" (33.0cm) 16" (40.6cm) Without Locked Doors 718B563M 718B566M 30" (76.2cm) 718B663M 718B666M 36" (91.4cm) 718B763M 718B766M 42" (106.7cm) 718B863M 718B866M 48" (121.9cm) With Locked Doors 718B563H 718B566H 30" (76.2cm) 718B663H 718B666H 36" (91.4cm) 718B763H 718B766H 42" (106.7cm) 718B863H 718B866H 48" (121.9cm) Note: For base cabinets, wall cases, upper cases and tall cases without finished bottoms, add suffix: Both ends finished = L (with lock) / J (no lock) R.H. end finished = K (with lock) / R (no lock) L.H. end finished = T (with lock) / F (no lock) Both ends unfinished = P (with lock) / U (no lock) For upper cases with finished bottoms, add suffix: Both ends finished = D (with lock) / B (no lock) R.H. end finished = N (with lock) / E (no lock) L.H. end finished = G (with lock) / A (no lock) Both ends unfinished = Y (with lock) / W (no lock) 26