Ammeraal Beltech Modular

Transcription

1 mmeraal eltech Modular Innovative belt and chain solutions for every industry & application

2 Content uni MP C page 3-6 uni MP 16% page 7-10 uni MP 18% page uni MP 20% page uni MP 22% page uni Pop-up flight page uni MP Flights page uni MP G page uni MP N page uni MP RO page 39-40

3 Datasheet: uni MP C EN Plastic Modular elt Series uni MP C P L T Straight running belt Nominal pitch: 50.8 mm (2.00 in) Surface type: Flat Surface opening: Closed ackflex radius: 65.0 mm (2.6 in) Pin diameter: 8 mm (0.31 in) STNDRD elt material & color POM-DI W PP W PE-I N Pin material & color PP W PE W P (Nominal) mm in mm in T L Non standard material and color: See uni Material and Color Overview. lternative pin and lock materials: Pin: P6.6 N PP W PE W PT LG SS304 Lockpin: P6.6 PT LG Trilock: P6.6 N elt width Permissible tensile force (elt/pin material) elt weight (elt/pin material) POM-DI/PP PP/PP PE-I/PE POM-DI/PP PP/PP PE-I/PE mm in N lbf N lbf N lbf Kg/m Ib/ft Kg/m Ib/ft Kg/m Ib/ft *Min. No. drive sprocket per shaft Number of wear strips (Min. No.) **Carry (pcs) **Return (pcs) STRIGT RUNNING dditional standard belt widths are available in steps of 16.8 mm (0.66 in.) PITC 50.8 MM/2.00 IN dditional standard belt widths are available in steps of 16.8 mm (0.66 in.) dditional standard belt widths are available in steps of 16.8 mm (0.66 in.) General belt tolerance is +0/-0.4% at 23 C/73 F. For exact belt width contact Customer Service. Non standard belt width on request. *Max. Load per Drive Sprocket. elt material: POM-DI with snub roller 2000 N (450 lbf) without snub roller 1250 N (281 lbf). **Max. Spacing between wear strips, Carry: 152 mm (6 in); Return: 304 mm (12 in). = Single Link 3

4 Datasheet: uni MP C Rubber Top C elt Rubber C Link Width mm in mm in mm in size mm in Curved Rough POM-DI W 01 N K Non Standard material and color: See uni Material and Color Overview. Flight See separate uni MP series Flight datasheet. Side Guard Side Guard mm in mm in mm in Closed PE-I N PP-I W *34.0 mm (1.34 in) combined with flight. Increment: 8.4 mm (0.33 in). Note: ackflex radius when Side Guards are used: mm (7.90 in) 4

5 Datasheet: uni MP C Tab K G J ottom old Down Tab Note: When using tabs, please verify sufficient clearance to the shaft. Max. shaft diameter = Sprocket pitch diameter mm (2.50 in). When using square shafts, please verify that the diagonal does not exceed max. diameter. Example: Sprocket z = 6: Max. shaft diameter = ø38.1 mm ( = ø1.4 in). Note: When using a belt system with tabs, the temperature should be constant. Please note that the tabs are not always placed in the middle of the belt. Non Standard material and color: See uni Material and Color Overview. Non standard uni mflight G J K mm in mm in mm in mm in POM-DI W Principle sketch Other non standard option: See uni mflight Overview. 5

6 Datasheet: uni MP C Sprocket No of teeth Pilot bore in mm ore size Overall diameter ubdiameter Pitchdiameter -dimension -dimension mm in mm in mm in mm in mm in Single row/one way Double row/two way Molded P6 LG Machined P6 N Z06 x x x Z08 x x x x Z10 x x x x Z x x x Z12 x x x x Z x x x Z x x Z16 x x x Non standard material and color: See uni Material and Color Overview. Molded sprocket Molded sprocket Molded sprocket Molded sprocket Molded sprocket Machined sprocket Machined sprocket Other sprocket sizes are available upon request. Two-part sprocket are available upon request. Round bores are always delivered with keyway. Other bore sizes are available upon request. uni Retainer Rings: See uni Retainer Ring data sheet Width of sprocket = Single row: 42.3 mm (1.66 in) Double row: 50.0 mm (1.96 in) Width of tooth = Single row: 9.5 mm (0.37 in) Double row: 17.0 mm (0.66 in) Max. load per sprocket shown does not take bore size into account. Please also ensure that sufficient size shaft is chosen for corresponding load. For correct sprocket position: See uni ssembly Instructions for uni MP. For more detailed sprocket information, contact Customer Service. uni MP C/ Conveyor elts Seamless elts Modular elts Timing elts Expert advice, quality solutions and local service for all your belting needs This information is subject to alteration due to continuous development. mmeraal eltech will not be held liable for the incorrect use of the above stated information. This information replaces previous information. ll activities performed and services rendered by mmeraal eltech are subject to general terms and conditions of sale and delivery, as applied by its operating companies. Transmission elts Fabrication & service mmeraal eltech Modular /S julmagervej 21 DK-7100 Vejle T F admin@unichains.com 6

7 Datasheet: uni MP 16% EN Plastic Modular elt Series uni MP 16% P L T Straight running belt Nominal pitch: 50.8 mm (2.00 in) Surface type: Flat Surface opening: 16% ackflex radius: 65.0 mm (2.60 in) Pin diameter: 8 mm (0.31 in) STNDRD elt material & color PP W PE-I N Pin material & color PP W PE W P (Nominal) mm in mm in T L Non standard material and color: See uni Material and Color Overview. lternative pin and lock materials: Pin: P6.6 N PP W PE W PT LG SS304 Lockpin: P6.6 PT LG Trilock: P6.6 N elt width Permissible tensile force (elt/pin material) elt weight (elt/pin material) PP/PP PE-I/PE PP/PP PE-I/PE mm in N lbf N lbf kg/m lb/ft kg/m lb/ft *Min. No. drive sprocket per shaft Number of wear strips (Min. No.) **Carry (pcs) **Return (pcs) STRIGT STNDRD RUNNING PITC 50.8 MM/2.00 IN dditional standard belt widths are available in steps of 50.3 mm (1.98 in) dditional non-standard belt widths are available in steps of 16.8 mm (0.66 in.) dditional standard belt widths are available in steps of 50.3 mm (1.98 in) dditional non-standard belt widths are available in steps of 16.8 mm (0.66 in.) General belt tolerance is +0/-0.4% at 23 C/73 F and 50% R. For exact belt width contact Customer Service. Non standard belt width on request. *Max. Load per Drive Sprocket. elt material: PP with snub roller 2000 N (450 lbf) without snub roller 1250 N (281 lbf). **Max. Spacing between wear strips, Carry: 152 mm (6 in); Return: 304 mm (12 in) = Single Link 7

8 Datasheet: uni MP 16% Rubber Top C elt Rubber C Link Width mm in mm in mm in size mm in Curved Rough POM-DI W 01 N K Non Standard material and color: See uni Material and Color Overview. Flight See separate uni MP series Flight datasheet. Side Guard Side Guard mm in mm in mm in Closed PE-I N PP-I W *34.0 mm (1.34 in) combined with flight. Increment: 8.4 mm (0.33 in). Note: ackflex radius when Side Guards are used: mm (7.90 in) 8

9 Datasheet: uni MP 16% Tab K G J ottom old Down Tab G J K mm in mm in mm in mm in POM-DI W Note: When using tabs, please verify sufficient clearance to the shaft. Max. shaft diameter = Sprocket pitch diameter mm (2.50 in). When using square shafts, please verify that the diagonal does not exceed max. diameter. Example: Sprocket z = 6: Max. shaft diameter = ø38.1 mm ( = ø1.4 in). Note: When using a belt system with tabs, the temperature should be constant. Please note that the tabs are not always placed in the middle of the belt. Non Standard material and color: See uni Material and Color Overview. Non standard uni mflight Principle sketch Other non standard option: See uni mflight Overview. 9

10 Datasheet: uni MP 16% Sprocket No of teeth Pilot bore in mm ore size Overall diameter ubdiameter Pitchdiameter -dimension -dimension mm in mm in mm in mm in mm in Single row/one way Double row/two way Molded P6 LG Machined P6 N Z06 x x x Z08 x x x x Z10 x x x x Z x x x Z12 x x x x Z x x x Z x x Z16 x x x Non standard material and color: See uni Material and Color Overview. Molded sprocket Molded sprocket Molded sprocket Molded sprocket Molded sprocket Machined sprocket Machined sprocket Other sprocket sizes are available upon request. Two-part sprocket are available upon request. Round bores are always delivered with keyway. Other bore sizes are available upon request. uni Retainer Rings: See uni Retainer Ring data sheet Width of sprocket = Single row: 42.3 mm (1.66 in) Double row: 50.0 mm (1.96 in) Width of tooth = Single row: 9.5 mm (0.37 in) Double row: 17.0 mm (0.66 in) Max. load per sprocket shown does not take bore size into account. Please also ensure that sufficient size shaft is chosen for corresponding load. For correct sprocket position: See uni ssembly Instructions for uni MP. For more detailed sprocket information, contact Customer Service. uni MP 16/ Conveyor elts Seamless elts Modular elts Timing elts Expert advice, quality solutions and local service for all your belting needs This information is subject to alteration due to continuous development. mmeraal eltech will not be held liable for the incorrect use of the above stated information. This information replaces previous information. ll activities performed and services rendered by mmeraal eltech are subject to general terms and conditions of sale and delivery, as applied by its operating companies. Transmission elts Fabrication & service mmeraal eltech Modular /S julmagervej 21 DK-7100 Vejle T F admin@unichains.com 10

11 Datasheet: uni MP 18% EN Plastic Modular elt Series uni MP 18% P L T Straight running belt Nominal pitch: 50.8 mm (2.00 in) Surface type: Flat Surface opening: 18% ackflex radius: 65.0 mm (2.6 in) Pin diameter: 8 mm (0.31 in) STNDRD elt material & color POM-DI W PP W PE-I N PP-W L Pin material & color PP W PE W PP-W L P (Nominal) mm in mm in T L Non standard material and color: See uni Material and Color Overview. lternative pin and lock materials: Pin: P6.6 N PP W PE W PT LG SS304 Lockpin: P6.6 PT LG Trilock: P6.6 N elt width POM-DI/PP Permissible tensile force (elt/pin material) PP/PP PP-W/PP-W PE-I/PE POM-DI/PP elt weight (elt/pin material) PP/PP PP-W/PP-W PE-I/PE mm in N lbf N lbf N lbf kg/m lb/ft kg/m lb/ft kg/m lb/ft *Min. No. drive sprocket per shaft Number of wear strips (Min. No.) **Carry (pcs) **Return (pcs) STRIGT RUNNING PITC 50.8 MM/2.00 IN dditional standard belt widths are available in steps of 50.3 mm (1.98 in.) dditional non-standard belt widths are available in steps of 16.8 mm (0.66 in) dditional standard belt widths are available in steps of 50.3 mm (1.98 in.) dditional non-standard belt widths are available in steps of 16.8 mm (0.66 in) General belt tolerance is +0/-0.4% at 23 C/73 F and 50% R. For exact belt width contact Customer Service. Non standard belt width on request. *Max. Load per Drive Sprocket. elt material: POM-DI with snub roller 2000 N (450 lbf) without snub roller 1250 N (281 lbf). **Max. Spacing between wear strips, Carry: 152 mm (6 in); Return: 304 mm (12 in). = Single Link 11

12 Rubber Top C elt Rubber C Link Width mm in mm in mm in size mm in Curved Rough POM-DI W 01 N K Non Standard material and color: See uni Material and Color Overview. Flight See separate uni MP series Flight datasheet. Side Guard Side Guard mm in mm in mm in Closed PE-I N PP-I W *34.0 mm (1.34 in) combined with flight. Increment: 8.4 mm (0.33 in). Note: ackflex radius when Side Guards are used: mm (7.90 in) 12

13 Tab K G J ottom old Down Tab G J K mm in mm in mm in mm in POM-DI W Note: When using tabs, please verify sufficient clearance to the shaft. Max. shaft diameter = Sprocket pitch diameter mm (2.50 in). When using square shafts, please verify that the diagonal does not exceed max. diameter. Example: Sprocket z = 6: Max. shaft diameter = ø38.1 mm ( = ø1.4 in). Note: When using a belt system with tabs, the temperature should be constant. Please note that the tabs are not always placed in the middle of the belt. Non Standard material and color: See uni Material and Color Overview. Non standard uni mflight Principle sketch Other non standard option: See uni mflight Overview. 13

14 Sprocket No of teeth Pilot bore in mm ore size Overall diameter ubdiameter Pitchdiameter -dimension -dimension mm in mm in mm in mm in mm in Single row/one way Double row/two way Molded P6 LG Machined P6 N Z06 x x x Z08 x x x x Z10 x x x x Z x x x Z12 x x x x Z x x x Z x x Z16 x x x Non standard material and color: See uni Material and Color Overview. Molded sprocket Molded sprocket Molded sprocket Molded sprocket Molded sprocket Machined sprocket Machined sprocket Other sprocket sizes are available upon request. Two-part sprocket are available upon request. Round bores are always delivered with keyway. Other bore sizes are available upon request. uni Retainer Rings: See uni Retainer Ring data sheet Width of sprocket = Single row: 42.3 mm (1.66 in) Double row: 50.0 mm (1.96 in) Width of tooth = Single row: 9.5 mm (0.37 in) Double row: 17.0 mm (0.66 in) Max. load per sprocket shown does not take bore size into account. Please also ensure that sufficient size shaft is chosen for corresponding load. For correct sprocket position: See uni ssembly Instructions for uni MP. For more detailed sprocket information, contact Customer Service. uni MP 18/ Conveyor elts Seamless elts Modular elts Timing elts Expert advice, quality solutions and local service for all your belting needs This information is subject to alteration due to continuous development. mmeraal eltech will not be held liable for the incorrect use of the above stated information. This information replaces previous information. ll activities performed and services rendered by mmeraal eltech are subject to general terms and conditions of sale and delivery, as applied by its operating companies. Transmission elts Fabrication & service mmeraal eltech Modular /S julmagervej 21 DK-7100 Vejle T F admin@unichains.com 14

15 Datasheet: uni MP 20% EN Plastic Modular elt Series uni MP 20% P L T Straight running belt Nominal pitch: 50.8 mm (2.00 in) Surface type: Flat Surface opening: 20% ackflex radius: 65.0 mm (2.6 in) Pin diameter: 8 mm (0.31 in) STNDRD elt material & color PP W PE-I N Pin material & color PP W PE W P (Nominal) mm in mm in T L Non standard material and color: See uni Material and Color Overview. lternative pin and lock materials: Pin: P6.6 N PP W PE W PT LG SS304 Lockpin: P6.6 PT LG Trilock: P6.6 N elt width Permissible tensile force (elt/pin material) elt weight (elt/pin material) PP/PP PE-I/PE PP/PP PE-I/PE mm in N lbf N lbf kg/m lb/ft kg/m lb/ft *Min. No. drive sprocket per shaft Number of wear strips (Min. No.) **Carry (pcs) **Return (pcs) STRIGT RUNNING PITC 50.8 MM/2.00 IN dditional standard belt widths are available in steps of 50.3 mm (1.98 in.) dditional non-standard belt widths are available in steps of 16.8 mm (0.66 in) dditional standard belt widths are available in steps of 50.3 mm (1.98 in.) dditional non-standard belt widths are available in steps of 16.8 mm (0.66 in) General belt tolerance is +0/-0.4% at 23 C/73 F and 50% R. For exact belt width contact Customer Service. Non standard belt width on request. *Max. Load per Drive Sprocket. elt material: PP with snub roller 2000 N (450 lbf) without snub roller 1250 N (281 lbf). **Max. Spacing between wear strips, Carry: 152 mm (6 in); Return: 304 mm (12 in). = Single Link 15

16 Datasheet: uni MP 20% Rubber Top C elt Rubber C Link Width mm in mm in mm in size mm in Curved Rough POM-DI W 01 N K Non Standard material and color: See uni Material and Color Overview. Flight See seperate uni MP series Flight datasheet. Side Guard Side Guard mm in mm in mm in Closed PE-I N PP-I W *34.0 mm (1.34 in) combined with flight. Increment: 8.4 mm (0.33 in). Note: ackflex radius when Side Guard are used: mm (7.90 in) 16

17 Datasheet: uni MP 20% Tab K G J ottom old Down Tab G J K mm in mm in mm in mm in POM-DI W Note: When using taps, please verify sufficient clearance to the shaft. Max. shaft diameter = Sprocket pitch diameter mm (2.50 in). When using square shafts, please verify that the diagonal does not exceed max. diameter. Example: Sprocket z = 6: Max. shaft diameter = ø38.1 mm ( = ø1.4 in). Note: When using a belt system with tabs, the temperature should be constant. Please note that the tabs are not always placed in the middle of the belt. Non Standard material and color: See uni Material and Color Overview. Non standard uni mflight Travel direction Principle sketch Other non standard option: See uni mflight Overview. 17

18 Datasheet: uni MP 20% Sprocket No of teeth Pilot bore in mm ore size Overall diameter ubdiameter Pitchdiameter -dimension -dimension mm in mm in mm in mm in mm in Single row/one way Double row/two way Molded P6 LG Machined P6 N Z06 x x x Z08 x x x x Z10 x x x x Z x x x Z12 x x x x Z x x x Z x x Z16 x x x Non standard material and color: See uni Material and Color Overview. Molded sprocket Molded sprocket Molded sprocket Molded sprocket Molded sprocket Machined sprocket Machined sprocket Other sprocket sizes are available upon request. Two-part sprocket are available upon request. Round bores are always delivered with keyway. Other bore sizes are available upon request. uni Retainer Rings: See uni Retainer Ring data sheet Width of sprocket = Single row: 42.3 mm (1.66 in) Double row: 50.0 mm (1.96 in) Width of tooth = Single row: 9.5 mm (0.37 in) Double row: 17.0 mm (0.66 in) Max. load per sprocket shown does not take bore size into account. Please also ensure that sufficient size shaft is chosen for corresponding load. For correct sprocket position: See uni ssembly Instructions for uni MP. For more detailed sprocket information, contact Customer Service. uni MP 20/ Conveyor elts Seamless elts Modular elts Timing elts Expert advice, quality solutions and local service for all your belting needs This information is subject to alteration due to continuous development. mmeraal eltech will not be held liable for the incorrect use of the above stated information. This information replaces previous information. ll activities performed and services rendered by mmeraal eltech are subject to general terms and conditions of sale and delivery, as applied by its operating companies. Transmission elts Fabrication & service mmeraal eltech Modular /S julmagervej 21 DK-7100 Vejle T F admin@unichains.com 18

19 Datasheet: uni MP 22% EN Plastic Modular elt Series uni MP 22% P L T Straight running belt Nominal pitch: 50.8 mm (2.00 in) Surface type: Flat Surface opening: 22% ackflex radius: 65.0 mm (2.6 in) Pin diameter: 8 mm (0.31 in) STNDRD elt material & color PP W PE-I N Pin material & color PP W PE W P (Nominal) mm in mm in T L Non standard material and color: See uni Material and Color Overview. lternative pin and lock materials: Pin: P6.6 N PP W PE W PT LG SS304 Lockpin: P6.6 PT LG Trilock: P6.6 N elt width Permissible tensile force (elt/pin material) elt weight (elt/pin material) PP/PP PE-I/PE PP/PP PE-I/PE mm in N lbf N lbf kg/m lb/ft kg/m lb/ft *Min. No. drive sprocket per shaft Number of wear strips (Min. No.) **Carry (pcs) **Return (pcs) STRIGT RUNNING PITC 50.8 MM/2.00 IN dditional standard belt widths are available in steps of 50.3 mm (1.98 in.) dditional non-standard belt widths are available in steps of 16.8 mm (0.66 in) dditional standard belt widths are available in steps of 50.3 mm (1.98 in.) dditional non-standard belt widths are available in steps of 16.8 mm (0.66 in) General belt tolerance is +0/-0.4% at 23 C/73 F and 50% R. For exact belt width contact Customer Service. Non standard belt width on request. *Max. Load per Drive Sprocket. elt material: PP with snub roller 2000 N (450 lbf) without snub roller 1250 N (281 lbf) **Max. Spacing between wear strips, Carry: 152 mm (6 in); Return: 304 mm (12 in). = Single Link 19

20 Datasheet: uni MP 22% Rubber Top C elt Rubber C Link Width mm in mm in mm in size mm in Curved Rough POM-DI W 01 N K Non Standard material and color: See uni Material and Color Overview. Flight See seperate uni MP series Flight datasheet. Side Guard Side Guard mm in mm in mm in Closed PE-I N PP-I W *34.0 mm (1.34 in) combined with flight. Increment: 8.4 mm (0.33 in). Note: ackflex radius when Side Guard are used: mm (7.90 in) 20

21 Datasheet: uni MP 22% Tab K G J ottom old Down Tab G J K mm in mm in mm in mm in POM-DI W Note: When using taps, please verify sufficient clearance to the shaft. Max. shaft diameter = Sprocket pitch diameter mm (2.50 in). When using square shafts, please verify that the diagonal does not exceed max. diameter. Example: Sprocket z = 6: Max. shaft diameter = ø38.1 mm ( = ø1.4 in). Note: When using a belt system with tabs, the temperature should be constant. Please note that the tabs are not always placed in the middle of the belt. Non Standard material and color: See uni Material and Color Overview. Non standard uni mflight Principle sketch Other non standard option: See uni mflight Overview. 21

22 Datasheet: uni MP 22% Sprocket No of teeth Pilot bore in mm ore size Overall diameter ubdiameter Pitchdiameter -dimension -dimension mm in mm in mm in mm in mm in Single row/one way Double row/two way Molded P6 LG Machined P6 N Z06 x x x Z08 x x x x Z10 x x x x Z x x x Z12 x x x x Z x x x Z x x Z16 x x x Non standard material and color: See uni Material and Color Overview. Molded sprocket Molded sprocket Molded sprocket Molded sprocket Molded sprocket Machined sprocket Machined sprocket Other sprocket sizes are available upon request. Two-part sprocket are available upon request. Round bores are always delivered with keyway. Other bore sizes are available upon request. uni Retainer Rings: See uni Retainer Ring data sheet Width of sprocket = Single row: 42.3 mm (1.66 in) Double row: 50.0 mm (1.96 in) Width of tooth = Single row: 9.5 mm (0.37 in) Double row: 17.0 mm (0.66 in) Max. load per sprocket shown does not take bore size into account. Please also ensure that sufficient size shaft is chosen for corresponding load. For correct sprocket position: See uni ssembly Instructions for uni MP. For more detailed sprocket information, contact Customer Service. uni MP 22/ / Conveyor elts Seamless elts Modular elts Timing elts Expert advice, quality solutions and local service for all your belting needs This information is subject to alteration due to continuous development. mmeraal eltech will not be held liable for the incorrect use of the above stated information. This information replaces previous information. ll activities performed and services rendered by mmeraal eltech are subject to general terms and conditions of sale and delivery, as applied by its operating companies. Transmission elts Fabrication & service mmeraal eltech Modular /S julmagervej 21 DK-7100 Vejle T F admin@unichains.com 22

23 Datasheet: uni MP Pop-up flight EN Plastic Modular elt uni MP Pop-up flight Travel direction I W I P T Straight running elevator belt Nominal pitch: 50.8 mm (2.00 in) Surface type: Flat Surface opening: Closed ackflex radius: 100 mm (3.9 in) min. Pin diameter: 8 mm (0.31 in) STNDRD elt material & color PP W PE-I N Pin material & color PP W PE W Flight material & color elt dimensions PP-I W PE-I W mm in mm in T I P Non standard material and color: See uni Material and Color Overview. lternative pin and lock materials: Pin: P6.6 N PP W PE W PT LG SS304 Lockpin: P6.6 PT LG elt load capacity Permissible tensile force (elt/pin material) elt width (W) Indents (I) * Flight width () PP/PP PE-I/PE Maximum product load per flight row STRIGT RUNNING mm in mm in mm in N lbf N lbf Kg Lbs General width tolerance is +0/-0.4% at 23 C/73 F. For other widths contact Customer Service. *Standard indent 34 mm (1.34 in), other indents upon request. PITC 50.8 MM/2.00 IN 23

24 Datasheet: uni MP Pop-up flight elt dimensions ase belt weight (elt/pin material) DD weight per flight row elt width (W) PP/PP PE-I/PE PP-I/PP PE-I/PE Min. no drive sprockets * Construction information No flight cams/ activation wearstrips Min number of support wearstrips mm in Kg/m Ib/ft Kg/m Ib/ft Kg/m Ib/ft Kg/m Ib/ft Pieces Pieces Pieces *Max. Load per Drive Sprocket. elt material: POM-DI with snub roller 2000 N (450 lbf) without snub roller 1250 N (281 lbf) Placing of activation wearstrips elt dimensions ctivation wearstrips Distance from belt left hand edge elt width (W) Indents * (I) Flight width () mm in mm in mm in mm in mm in mm in mm in mm in mm in *Standard indent 34 mm (1.34 in), other indents upon request. W I I = Placing of activation wearstrip Dimensions for Pop-up flight system are from left hand edge of belt, looking down from top of belt with travel direction moving away from viewing point. 24

25 Datasheet: uni MP Pop-up flight Placing of sprockets elt dimensions Min. No elt width (W) Indents * (I) Flight width () drive S1 S2 S3 S4 sprockets ** Sprocket Position Distance from belt left hand edge mm in mm in mm in mm in mm in mm in mm in *Standard indent 34 mm (1.34 in), other indents upon request. **Max. Load per Drive Sprocket. elt material: POM-DI with snub roller 2000 N (450 lbf) without snub roller 1250 N (281 lbf) S1 S2 S3 S4 = Placing of sprockets Ensure sprockets cannot contact the Pop-up flight activation cams. These cams hinge below the belt surface when unsupported by wear-strips. If needed use extra retaining rings each side of floating sprockets to ensure they cannot contact the activation cams but can still float sideways. 25

26 Datasheet: uni MP Pop-up flight Sprocket No of teeth Pilot bore in mm ore size Overall diameter Pitchdiameter ubdiameter Dimension Dimension mm in mm in mm in mm in mm in Single row/one way Double row/two way Molded P6 LG Machined P6 N Z08 x x x Z10 x x x Z x x Z12 x x x Z x x Z16 x x x Molded sprocket Molded sprocket Machined sprocket Machined sprocket Non standard material and color: See uni Material and Color Overview. uni MP Single row one way sprockets as shown above are recommended for use with Pop-up flight system. uni MP Two row two way sprockets are available and can be used for conveyors which needed to reverse travel direction. Other sprocket sizes are available upon request. Two-part sprocket are available upon request. Round bores are always delivered with keyway. Other bore sizes are available upon request. uni Retainer Rings: See uni Retainer Ring data sheet. Width of sprocket = Single row: 42.3 mm (1.67 in) Width of tooth = Single row: 9.5 mm (0.37 in) Max load per sprocket shown does not take bore size into account. Please also ensure that sufficient size shaft is chosen for corresponding load. For more detailed sprocket information, contact Customer Service. uni MP Pop-up flight C/ Conveyor elts Seamless elts Modular elts Timing elts Expert advice, quality solutions and local service for all your belting needs This information is subject to alteration due to continuous development. mmeraal eltech will not be held liable for the incorrect use of the above stated information. This information replaces previous information. ll activities performed and services rendered by mmeraal eltech are subject to general terms and conditions of sale and delivery, as applied by its operating companies. Transmission elts Fabrication & service mmeraal eltech Modular /S julmagervej 21 DK-7100 Vejle T F admin@unichains.com 26

27 Datasheet: uni MP Flights EN Plastic Modular elt uni MP Flights STNDRD Link Width Indent both sides mm in size mm in mm in PE-I N Flat PP-I W PE-I N POM-D W K STRIGT RUNNING PP-I W PE-I N * *Indent only in one side. Depending on height and spacing the use of product supports may influence the backflex radius. PITC 50.8 MM/2.00 IN 27

28 Datasheet: uni MP Flights Link Width Indent both sides mm in size mm in mm in Non Stick PP-I W N PE-I W N K Link Width Indent both sides mm in size mm in mm in % Non Stick PP-I W N PE-I W N K

29 Datasheet: uni MP Flights Link Width Indent both sides mm in mm in size mm in mm in PP-I W ent PP-I W PE-I N K PP-I W Link Width Indent both sides mm in mm in size mm in mm in Cupped PP-I W K Photo will be updated Link Width Indent both sides mm in mm in size mm in mm in Cupped drain PP-I W K

30 Datasheet: uni MP Flights Link Width Indent both sides mm in size mm in mm in Flat 20% PE-I N K Link Width Indent both sides mm in size mm in mm in Flat 22% PE-I PE-I N W K Conveyor elts Seamless elts Modular elts Timing elts uni MP flights/ Expert advice, quality solutions and local service for all your belting needs This information is subject to alteration due to continuous development. mmeraal eltech will not be held liable for the incorrect use of the above stated information. This information replaces previous information. ll activities performed and services rendered by mmeraal eltech are subject to general terms and conditions of sale and delivery, as applied by its operating companies. Transmission elts Fabrication & service mmeraal eltech Modular /S julmagervej 21 DK-7100 Vejle T F admin@unichains.com 30

31 Datasheet: uni MP G EN Plastic Modular elt Series uni MP G R P L T Straight running belt Nominal pitch: 50.8 mm (2.00 in) Surface type: Grip Surface opening: Closed ackflex radius: 65.0 mm (2.6 in) Pin diameter: 8 mm (0.31 in) STNDRD elt material & color POM-DI W P (Nominal) mm in mm in R Pin material & color PP W L T Non standard material and color: See uni Material and Color Overview. lternative pin and lock materials: Pin: P6.6 N PP W PE W PT LG SS304 Lockpin: P6.6 PT LG Trilock: P6.6 N uni MP G is available with a molded indent of 35.0 mm (1.38 in) in both sides. elt width Permissible tensile force (elt/pin material) POM-DI/PP elt weight (elt/pin material) POM-DI/PP mm in N lbf kg/m lb/ft *Min. No. drive sprocket per shaft Number of wear strips (Min. No.) **Carry (pcs) **Return (pcs) STRIGT RUNNING PITC 50.8 MM/2.00 IN dditional standard belt widths are available in steps of 50.3 mm (1.98 in.) dditional non-standard belt widths are available in steps of 16.8 mm (0.66 in) dditional standard belt widths are available in steps of 50.3 mm (1.98 in.) dditional non-standard belt widths are available in steps of 16.8 mm (0.66 in) General belt tolerance is +0/-0.4% at 23 C/73 F and 50% R. For exact belt width contact Customer Service. Non standard belt width on request. *Max. Load per Drive Sprocket. elt material: POM-DI with snub roller 2000 N (450 lbf) without snub roller 1250 N (281 lbf). **Max. Spacing between wear strips, Carry: 152 mm (6 in); Return: 304 mm (12 in). = Single Link 31

32 Datasheet: uni MP G Flight See seperate uni MP series Flight datasheet. Side Guard Side Guard mm in mm in mm in Closed PE-I N PP-I W *34.0 mm (1.34 in) combined with flight. Increment: 8.4 mm (0.33 in). ackflex radius when Side Guard are used: mm (7.90 in). Tab K G J ottom old Down Tab G J K mm in mm in mm in mm in POM-DI W Note: When using taps, please verify sufficient clearance to the shaft. Max. shaft diameter = Sprocket pitch diameter mm (2.50 in). When using square shafts, please verify that the diagonal does not exceed max. diameter. Example: Sprocket z = 6: Max. shaft diameter = ø38.1 mm ( = ø1.4 in). Note: When using a belt system with tabs, the temperature should be constant. Please note that the tabs are not always placed in the middle of the belt. Non Standard material and color: See uni Material and Color Overview. 32

33 Datasheet: uni MP G Sprocket No of teeth Pilot bore in mm ore size Overall diameter ubdiameter Pitchdiameter -dimension -dimension mm in mm in mm in mm in mm in Single row/one way Double row/two way Molded P6 LG Machined P6 N Z06 x x x Z08 x x x x Z10 x x x x Z x x x Z12 x x x x Z x x x Z x x Z16 x x x Non standard material and color: See uni Material and Color Overview. Molded sprocket Molded sprocket Molded sprocket Molded sprocket Molded sprocket Machined sprocket Machined sprocket Other sprocket sizes are available upon request. Two-part sprocket are available upon request. Round bores are always delivered with keyway. Other bore sizes are available upon request. uni Retainer Rings: See uni Retainer Ring data sheet Width of sprocket = Single row: 42.3 mm (1.66 in) Double row: 50.0 mm (1.96 in) Width of tooth = Single row: 9.5 mm (0.37 in) Double row: 17.0 mm (0.66 in) Max. load per sprocket shown does not take bore size into account. Please also ensure that sufficient size shaft is chosen for corresponding load. For correct sprocket position: See uni ssembly Instructions for uni MP. For more detailed sprocket information, contact Customer Service. 33

34 Datasheet: uni MP G uni MP G/ Conveyor elts Seamless elts Modular elts Timing elts Expert advice, quality solutions and local service for all your belting needs This information is subject to alteration due to continuous development. mmeraal eltech will not be held liable for the incorrect use of the above stated information. This information replaces previous information. ll activities performed and services rendered by mmeraal eltech are subject to general terms and conditions of sale and delivery, as applied by its operating companies. Transmission elts Fabrication & service mmeraal eltech Modular /S julmagervej 21 DK-7100 Vejle T F admin@unichains.com 34

35 Datasheet: uni MP N EN Plastic Modular elt Series uni MP N elt material & color PE-I N Pin material & color PE W elt width Permissible tensile force (elt/pin material) P S P (Nominal) L T Straight running belt Nominal pitch: 50.8 mm (2.00 in) Surface type: No Cling Surface opening: Closed ackflex radius: 65.0 mm (2.6 in) Pin diameter: 8 mm (0.31 in) mm in mm in S L T Non standard material and color: See uni Material and Color Overview. lternative pin and lock materials: Pin: P6.6 N PP W PE W PT LG SS304 Lockpin: P6.6 PT LG Trilock: P6.6 N uni MP N is available with a molded indent of 35.0 mm (1.38 in) in both sides. PE-I/PE elt weight (elt/pin material) PE-I/PE mm in N lbf kg/m lb/ft *Min. No. drive sprocket per shaft Number of wear strips (Min. No.) **Carry (pcs) **Return (pcs) PITC 50.8 MM/2.00 IN STRIGT RUNNING STNDRD dditional standard belt widths are available in steps of 50.3 mm (1.98 in.) dditional non-standard belt widths are available in steps of 16.8 mm (0.66 in) dditional standard belt widths are available in steps of 50.3 mm (1.98 in.) dditional non-standard belt widths are available in steps of 16.8 mm (0.66 in) General belt tolerance is +0/-0.4% at 23 C/73 F and 50% R. For exact belt width contact Customer Service. Non standard belt width on request. *Max. Load per Drive Sprocket. elt material: POM-DI with snub roller 2000 N (450 lbf) without snub roller 1250 N (281 lbf). **Max. Spacing between wear strips, Carry: 152 mm (6 in); Return: 304 mm (12 in). = Single Link 35

36 Datasheet: uni MP N Flight See seperate uni MP series Flight datasheet. Side Guard Side Guard mm in mm in mm in Closed PE-I N PP-I W *34.0 mm (1.34 in) combined with flight. Increment: 8.4 mm (0.33 in). Note: ackflex radius when Side Guard are used: mm (7.90 in). Tab K G J ottom old Down Tab G J K mm in mm in mm in mm in POM-DI W Note: When using taps, please verify sufficient clearance to the shaft. Max. shaft diameter = Sprocket pitch diameter mm (2.50 in). When using square shafts, please verify that the diagonal does not exceed max. diameter. Example: Sprocket z = 6: Max. shaft diameter = ø38.1 mm ( = ø1.4 in). Note: When using a belt system with tabs, the temperature should be constant. Please note that the tabs are not always placed in the middle of the belt. Non Standard material and color: See uni Material and Color Overview. 36

37 Datasheet: uni MP N Sprocket No of teeth Pilot bore in mm ore size Overall diameter ubdiameter Pitchdiameter -dimension -dimension mm in mm in mm in mm in mm in Single row/one way Double row/two way Molded P6 LG Machined P6 N Z06 x x x Z08 x x x x Z10 x x x x Z x x x Z12 x x x x Z x x x Z x x Z16 x x x Non standard material and color: See uni Material and Color Overview. Molded sprocket Molded sprocket Molded sprocket Molded sprocket Molded sprocket Machined sprocket Machined sprocket Other sprocket sizes are available upon request. Two-part sprocket are available upon request. Round bores are always delivered with keyway. Other bore sizes are available upon request. uni Retainer Rings: See uni Retainer Ring data sheet Width of sprocket = Single row: 42.3 mm (1.66 in) Double row: 50.0 mm (1.96 in) Width of tooth = Single row: 9.5 mm (0.37 in) Double row: 17.0 mm (0.66 in) Max. load per sprocket shown does not take bore size into account. Please also ensure that sufficient size shaft is chosen for corresponding load. For correct sprocket position: See uni ssembly Instructions for uni MP. For more detailed sprocket information, contact Customer Service. 37