Ammeraal Beltech Modular

Transcription

1 Ammeraal Beltech Modular Innovative belt and chain solutions for every industry & application

2 Content uni Flex SNB C 2.3 page 3-10 uni Flex SNB C 1.6 page uni Flex SNB 2.3 page uni Flex SNB W 2.3 page uni Flex SNB WO 2.3 page uni Flex SNB W 2.3 page 43-50

3 lastic Modular Belt Series uni Flex SNB uni Flex SNB C 1.6 uni Flex SNB C 2.3 uni Flex SNB W 2.3 Surface Opening: 55% Sideflexing belt Nominal pitch: 25.4 mm (1.00 in) Surface type: Flat Surface opening: 47%/55% Backflex radius: 25.0 mm (0.98 in) in diameter: 5.0 mm (0.20 in) Min. inside radius: 1.6 x belt width, 2.3 x belt width uni Flex SNB 2.3 Surface Opening: 55% uni Flex SNB W 2.3 Surface Opening: 55% (Nominal) mm in mm in A A ICH 25.4 MM/1.00 IN SIDE FEXING SANDAD uni Flex SNB WO 2.3 Surface Opening: 55% 3

4 uni Flex SNB C ubber op 1.6 uni Flex SNB CI ubber op 2.3 mm in mm in (Nominal) uni Flex SNB C ubber op 2.3 Indent uni Flex SNB C ubber op 1.6 is 26.5 mm (1.04 in). uni Flex SNB CI ubber op 2.3 is 7.0 mm (0.28 in). uni Flex SNB C ubber op 2.3 is available without indent. ype Belt materials and colors in materials and colors uni Flex SNB C 1.6 uni Flex SNB C 2.3 uni Flex SNB 2.3* OM-D B W B W A6.6 B W B G uni Flex SNB C 2.3 OM-D B W uni Flex SNB W uni Flex SNB WO A6.6 B W SS304 uni Flex SNB W A6.6 B W SS304 B G uni Flex SNB C ubber op 1.6 uni Flex SNB CI ubber op 2.3 uni Flex SNB CI ubber op 2.3 B W + 03 K B W + 03 N B G Standard materials and colors ockingplates W B Wearpart and O-ab A6.6 W B For high speed or load abrasive applications: Wearpart and O-ab OM-DK N Non standard material and color: See uni Material and Color Overview. Alternative pin materials: A6.6 B N 4

5 uni Flex SNB C 1.6 ermissible tensile force OM-D/B /B A6.6/B OM-D /B /B Additional non-standard belt widths are available in steps of 12.7 mm (0.50 in). Flex SNB-C locked with wearpart or O-tabs both sides are 6 mm wider than the dimensions in the table above. *Max. oad per Drive Sprocket. Belt material: OM-D 1000 N (225 lbf), 850 N (191 lbf), A N (225 lbf). **Max. Spacing between wear strips, Carry: 152 mm (6 in); eturn: 304 mm (12 in). A6.6/B uni Flex SNB C 2.3 / uni Flex SNB 2.3 ermissible tensile force OM-D/B /B A6.6/B /B Flex SNB- locked with wearpart or O-tabs both sides are 6 mm wider than the dimensions in the table above. *Max. oad per Drive Sprocket. Belt material: OM-D 1000 N (225 lbf), 850 N (191 lbf), A N (225 lbf) **Max. Spacing between wear strips, Carry: 152 mm (6 in); eturn: 304 mm (12 in) A6.6/B Additional standard belt widths are available in steps of 76.0 mm (2.99 in) Additional non-standard belt widths are available in steps of 12.7 mm (0.50 in) Additional standard belt widths are available in steps of 76.0 mm (2.99 in) Additional non-standard belt widths are available in steps of 12.7 mm (0.50 in)

6 uni Flex SNB W 2.3 / uni Flex SNB WO 2.3 OM-D/SS ermissible tensile force OM-D/SS OM-D/SS Outer modules are always in A6.6 on belts wider than 234 mm (9.21 in). Belts up to 234 mm (9.21 in) in width is only available in A6.6. *Max. oad per Drive Sprocket. Belt material: OM-D 1000 N (225 lbf), 850 N (191 lbf), A N (225 lbf). **Max. Spacing between wear strips, Carry: 152 mm (6 in); eturn: 304 mm (12 in). Outer modules are always in A6.6 on belts wider than 234 mm (9.21 in). Belts up to 234 mm (9.21 in) in width is only available in A6.6. *Max. oad per Drive Sprocket. Belt material: OM-D 1000 N (225 lbf), 850 N (191 lbf), A N (225 lbf). **Max. Spacing between wear strips, Carry: 152 mm (6 in); eturn: 304 mm (12 in) Additional standard belt widths are available in steps of 76.0 mm (2.99 in) Additional non-standard belt widths are available in steps of 12.7 mm (0.50 in) Additional standard belt widths are available in steps of 76.0 mm (2.99 in) Additional non-standard belt widths are available in steps of 12.7 mm (0.50 in) uni Flex SNB W 2.3 B pins ermissible tensile force OM-D/B /B A6.6/B OM-D/B /B A6.6/B Additional standard belt widths are available in steps of 76.0 mm (2.99 in) Additional non-standard belt widths are available in steps of 12.7 mm (0.50 in) Additional standard belt widths are available in steps of 76.0 mm (2.99 in) Additional non-standard belt widths are available in steps of 12.7 mm (0.50 in)

7 uni Flex SNB W 2.3 SS pins OM-D/SS ermissible tensile force /SS A6.6/SS Outer modules are always in A6.6 on belts wider than 234 mm (9.21 in). Belts up to 234 mm (9.21 in) in width is only available in A6.6. *Max. oad per Drive Sprocket. Belt material: OM-D 1000 N (225 lbf), 850 N (191 lbf), A N (225 lbf). **Max. Spacing between wear strips, Carry: 152 mm (6 in); eturn: 304 mm (12 in) Additional standard belt widths are available in steps of 76.0 mm (2.99 in) Additional non-standard belt widths are available in steps of 12.7 mm (0.50 in) Additional standard belt widths are available in steps of 76.0 mm (2.99 in) Additional non-standard belt widths are available in steps of 12.7 mm (0.50 in)

8 Belt racking og Control Systems (W) Basic belt types can be combined with the belt tracking and control systems below to enhance performance. Basic belt types can be combined with the belt tracking and control systems below to enhance performance. uni Flex SNB 2.3 Standard (W) W - 6 mm (0.24 in) Wearpart system made of heat and wear resistant nylon to reduce the friction between belt edge and wearstrip. Only this part needs to be replaced when it has been worn out, not the entire belt. Wearpart W + 12 mm (0.47 in) (W) W - 6 mm (0.24 in) Outer edge tab system made of heat and wear resis tant nylon to reduce the friction between belt edge and wear strip. Using a slotted wear-strip, the O-ab will track the belt and allow the conveyed products to be wider than the belt. Height of O-ab: 6.4 mm (0.25 in) Height of slot: 8.0 mm (0.31 in) O-ab Intermediate tabs (I-ab) are placed on the bottom side of the belt to hold it down on incline conveyors. he intermediate tabs will fit anywhere across the belt bottom and at pitch multiples of 12.7 mm (0.50 in). I-ab (W) W - 68 mm (2.68 in) Side tab (S-ab) for holding the belt down. Normally used for wide belts. With S-abs, Ammerral Beltech modular A/S recommend that the radial forces in the curve are transferred by the inside edge of the belt similar to uni Flex SNB and uni Flex SNB W. einforcement link = 34.0 mm (1.34 in). S-ab ype Belt tracking and control combination Wearpart O-ab S-ab I-ab When using S-abs, please verify sufficient clearance to the shaft. Max. shaft diameter = Sprocket pitch diameter mm (2.00 in). uni Flex SNB uni Flex SNB C 1.6 uni Flex SNB C uni Flex SNB W uni Flex SNB W uni Flex SNB WO When using square shafts, please verify that the diagonal does not exceed max. diameter. Example: Sprocket z = 10: Max. shaft diameter = ø31 mm ( = ø1.2 in). - Standard Unavailable + Optional 8

9 Accessories Click on Flight 50.8 mm (2.00 in) Click on Flight 25.4 mm (1.00 in) ubber Support: Made-o-Order Click on Flight ow: Made-o-Order ubber op Side Guard Accessories Side Guard / Standard ype Belt material & color mm Height in Side Guard -I B W Accessories Flight / Standard ype Belt material & color ink size Height Width mm in mm in Flat A6.6 B W K300 B W Support / MO ype Support material & color H Width ength mm in mm in mm in ubber Support 01 N Click on Flight ow OM-D W Accessories Minimum Indents (I) ype ubber op Side Guard Click on Flights without Side Guard Click on Flights with Side Guard eft ight eft ight eft ight eft ight mm in mm in mm in mm in mm in mm in mm in mm in uni Flex SNB C uni Flex SNB uni Flex SNB C uni Flex SNB W uni Flex SNB WO uni Flex SNB W 2.3* uni Flex SNB W 2.3** * Even distance between Click on Flight rows ** Odd distance between Click on Flight rows 9

10 Made-o-Order Selection A B C uni Flex SNB with ollers ø17 x 5.5 mm (ø0.67 x 0.22 in) ype lastic Sprocket oller material & color OM-D W Made-o-Oder Materials: OM-D,, A6.6 and oller Material OM-D. Non standard oller material and color: See uni Material and Color verview. A B C mm in mm in mm in No. of teeth ilot Bore in mm Bore size Overall diameter itch diameter Hub diameter Dimension A Dimension B mm in mm in mm in mm in mm in Single row/wo way Double row/wo way Molded A6 G Machined A6 N Z09 x x x Z10 x x x Z12 x x x Z15 x x x Z18 x x x Z19 x x x Molded Molded B Non standard material and color: See uni Material and Color Overview. A Other sizes are available upon request. wo-part are available upon request. Other bore sizes are available upon request. uni etainer ings: See uni etainer ing data sheet. Width of tooth = 4.0 mm (0.16 in). Width of = 25.0 mm (0.98 in). Max. load per shown does not take bore size into account. lease also ensure that sufficient size shaft is chosen for corresponding load. For correct position: See uni Assembly Instructions for uni Flex ASB. For more detailed information, contact Customer Service. uni Flex SNB/ Conveyor Belts Seamless Belts Modular Belts iming Belts Expert advice, quality solutions and local service for all your belting needs his information is subject to alteration due to continuous development. Ammeraal Beltech will not be held liable for the incorrect use of the above stated information. his information replaces previous information. All activities performed and services rendered by Ammeraal Beltech are subject to general terms and conditions of sale and delivery, as applied by its operating companies. ransmission Belts Fabrication & service Ammeraal Beltech Modular A/S Hjulmagervej 21 DK-7100 Vejle F admin@unichains.com 10

17 Accessories Click on Flight 50.8 mm (2.00 in) Click on Flight 25.4 mm (1.00 in) ubber Support: Made-o-Order Click on Flight ow: Made-o-Order ubber op Side Guard Accessories Side Guard / Standard ype Belt material & color mm Height in Side Guard -I B W Accessories Flight / Standard ype Belt material & color ink size Height Width mm in mm in Flat A6.6 B W K300 B W Support / MO ype Support material & color H Width ength mm in mm in mm in ubber Support 01 N Click on Flight ow OM-D W Accessories Minimum Indents (I) ype ubber op Side Guard Click on Flights without Side Guard Click on Flights with Side Guard eft ight eft ight eft ight eft ight mm in mm in mm in mm in mm in mm in mm in mm in uni Flex SNB C uni Flex SNB uni Flex SNB C uni Flex SNB W uni Flex SNB WO uni Flex SNB W 2.3* uni Flex SNB W 2.3** * Even distance between Click on Flight rows ** Odd distance between Click on Flight rows 17

18 Made-o-Order Selection A B C uni Flex SNB with ollers ø17 x 5.5 mm (ø0.67 x 0.22 in) ype lastic Sprocket oller material & color OM-D W Made-o-Oder Materials: OM-D,, A6.6 and oller Material OM-D. Non standard oller material and color: See uni Material and Color verview. A B C mm in mm in mm in No. of teeth ilot Bore in mm Bore size Overall diameter itch diameter Hub diameter Dimension A Dimension B mm in mm in mm in mm in mm in Single row/wo way Double row/wo way Molded A6 G Machined A6 N Z09 x x x Z10 x x x Z12 x x x Z15 x x x Z18 x x x Z19 x x x Molded Molded B Non standard material and color: See uni Material and Color Overview. A Other sizes are available upon request. wo-part are available upon request. Other bore sizes are available upon request. uni etainer ings: See uni etainer ing data sheet. Width of tooth = 4.0 mm (0.16 in). Width of = 25.0 mm (0.98 in). Max. load per shown does not take bore size into account. lease also ensure that sufficient size shaft is chosen for corresponding load. For correct position: See uni Assembly Instructions for uni Flex ASB. For more detailed information, contact Customer Service. uni Flex SNB/ Conveyor Belts Seamless Belts Modular Belts iming Belts Expert advice, quality solutions and local service for all your belting needs his information is subject to alteration due to continuous development. Ammeraal Beltech will not be held liable for the incorrect use of the above stated information. his information replaces previous information. All activities performed and services rendered by Ammeraal Beltech are subject to general terms and conditions of sale and delivery, as applied by its operating companies. ransmission Belts Fabrication & service Ammeraal Beltech Modular A/S Hjulmagervej 21 DK-7100 Vejle F admin@unichains.com 18