Main Catalog. Terminal blocks Insulation displacement ADO System

Transcription

1 Main Catalog Terminal blocks displacement System

2

3 Summary Presentation... - Selection guide clamp connection Feed through terminal blocks... Feed through terminal blocks - Double-deck... - Terminal blocks for neutral circuits... Ground terminal blocks not electrically connected to the mounting rail... 8 Ground terminal blocks electrically connected to the mounting rail... 9 Heavy duty switch terminal blocks with blade Heavy duty switch terminal blocks with plug... - Heavy duty switch terminal blocks with fuse holder plug for automotive Mini Fuse... Fuse holder terminal blocks for x0 mm (.9x.8 in.) and x mm (.9x.98 in.) fuses Neutral switch blocks... - Terminal blocks with safety connection... Miniblocks... Feed through miniblocks on DIN rail... - Ground miniblocks not electrically connected to the DIN mounting rail... Ground miniblocks electrically connected to the DIN mounting rail... 8 Feed through miniblocks on DIN rail Ground miniblocks not electrically connected to the DIN mounting rail... Ground miniblocks electrically connected to the DIN mounting rail... Feed through miniblocks base mounted with flanges... - Ground miniblocks not electrically connected to the mounting plate... Feed through miniblocks base mounted with snap in mounting foot... - Ground miniblocks not electrically connected to the mounting plate connection Feed through terminal blocks Feed through terminal blocks - Double-deck Terminal blocks for sensors / actuators Terminal blocks for neutral circuits... Terminal blocks for neutral conductors... Ground terminal blocks not electrically connected to the mounting rail... Ground terminal blocks electrically connected to the mounting rail... Heavy duty switch terminal blocks with blade Heavy duty switch terminal blocks with plug Heavy duty switch terminal blocks with fuse holder plug for automotive Mini Fuse... Fuse holder terminal blocks for x0 mm (.9x.8 in.) and x mm (.9x.98 in.) fuses... - Neutral switch block... - Component holder terminal blocks... 8 Miniblocks... 9 Feed through miniblocks on DIN rail Ground miniblocks not electrically connected to the DIN mounting rail... 8 Ground miniblocks electrically connected to the DIN mounting rail... 8 Feed through miniblocks on DIN rail Ground miniblocks not electrically connected to the DIN mounting rail... 8 Ground miniblocks electrically connected to the DIN mounting rail... 8 Feed through miniblocks base mounted with flanges Ground miniblocks not electrically connected to the mounting plate Feed through miniblocks base mounted with snap in mounting foot Ground miniblocks not electrically connected to the mounting plate Pluggable terminal blocks Terminal blocks Female plugs Male plugs terminal blocks for railway applications Pluggable terminal blocks for railway applications Terminal blocks Female plugs... - Male plugs... - Tools, test connectors, accessories Marking Alphanumeric... Low Products & Systems ABB Inc LV009 [SXU0009C00] - June 00

4 Terminal blocks displacement - clamp DIN D,/.. Spacing mm +0,0.98"." Color Part number D,/ side side 0. - mm² 0. -, mm² - 8 AWG - AWG.0" 8,.9".9" D,/. with partition 099. End stop th. 9 mm BADL V End stop th. 0 mm BAM V 00. End stop th. 0 mm BAM V0 V ail x, x P.Z ail x x, P ail x x, P Other end stops, rails and accessories : see section on accessories. 0,- mm² - AWG 0,-,mm² - AWG 0,- mm² -8 AWG 0,- mm² -8 AWG 000 V 8 kv 00 V, A A mm² 8 AWG Wire stripping ecommended ecommended length (screw) (screw) torque (screw) Protection 9, mm, mm 0,-0, Nm IP 0.".".-. lb.in NEMA Notes Standard block mm spacing. For multiple wires connection, the wires need to be of the same gauge and nature (solid or stranded). Terminal block body material is UL 9 V0. Part number 8 0 End section grey blue yellow Test socket Test device Test plug Assembled jumper bar (without IP0 protection) Assembled jumper bar (with IP0 protection) Jumper bar not assembled Post + screw + washer 8 less jumper bar orange IP0 9 Jumper bar 0 less jumper bar to be inserted into jaw orange IP0 Comb-type jumper bar Isolating cover Shield connector Hand tool kit Semi-automatic tool Pneumatic tool kit eplacement head kit Extraction tool kit 8 Test connector FEDAD th. mm FEDAD th. mm FEDAD th. mm AL DIA. mm DCB FC blue DIA. mm BJM () A BJM () A BJM () A BJM () A BJM () A 0 BJMI () A BJMI () A BJMI () A BJMI () A BJMI () A 0 BJS () A 0 EV () BJE. () 0 A BJE. () 0 A BJE. () 0 A BJE. () 0 A BJE. () 0 A BJE. () 0 A BJE.8 () 0 A 8 BJE.9 () 0 A 9 BJE.0 () 0 A 0 BJB BJ., A BJ., A BJ., A BJ., A BJ.0, A 0 BJ.0, A 0 PC 0 A PC 0 A 0 EIP CBM th. 0, mm CBM8 th. 0,8 mm D CE. CEE See section on markers marking method C C0 TM () Use of these accessories requires the user to cut out the partition. Low Products & Systems ABB Inc LV009 [SXU0009C00] - June 00

5 Presentation System is a composition of two complementary pieces : The IDC Connection : System : high speed and cost savings 80 % time saving... The tool : Cut the wire Insert Actuate the tool The System takes the electrical connection into a new era : Simple multi-function tool for reliable and long-term connections without effort. - Connection : seconds away High productivity benefits by eliminating unnecessary actions eliable, fast, vibration- and corrosion-proof Elimination of conductor preparation risks No need of ferrule By using System, the following risks no longer exist: Stripping operation overlooked All strands not connected Stripping length too long or too short Tightening torque not respected not respected Worn or poorly adapted crimping tools Ferrules poorly crimped System is the only wiring concept where connection is independent from operator - The tool is locked on the block during the entire connection process - The tool guarantees a simple, good and secure connection - The tool ensures reproduction of connection quality, connection after connection, without operator fatigue Low Products & Systems LV009 [SXU0009C00] - June 00 ABB Inc

6 Presentation System is the best solution for applications with vibration, compared to other connection technologies System offers exceptional vibration and shock withstand performance with its double gripping of non-stripped conductors. esults : No loosening of screws No contact bounce - No cut cable strands System : high speed and cost savings With the strong System consecutive improvement and advantages in hand, we can take the next steps to bring to our customers the level of sustainable performance required. Provide added value to your customers, helping them to reduce costs, to improve efficiency and to restore some processes. Unstripped insulator absorbs vibrations Wire insulation is pinched by terminal block insulation Contact forces are permanently balanced Copper alloy jaw pinches the wire at two points System is the best solution for applications with corrosion, compared to other connection technologies Low galvanic couple of copper alloy jaw Sealed contact point End of wire (non isolated) is far from contact points System : The XXI st century connection Eliminates unnecessary actions Time reduction 00% secured connection Vibration-proof specialist Anti-corrosion specialist Low Products & Systems ABB Inc LV009 [SXU0009C00] - June 00

7 Selection guide SCEW CLAMP - FEED THOUGH NEUTAL CICUIT GOUND DOUBLE DECK Page to Page Page 8-9 Page to IDC TEMINAL BLOCKS wire size : 0. to 0 mm² ( to 8 AWG) Spacing : to 8 mm (.98" to.") wire size : 0. to 0 mm² ( to 8 AWG) Spacing : to 8 mm (.98" to.") :. to A :. to A wire size : 0. to 0 mm² ( to 8 AWG) wire size : 0. to 0 mm² ( to 0 AWG) Spacing : to 8 mm (.98" to.") Spacing : to 8 mm (.8" to.") : 0 to 80 A/s :. to A (80 A/ s. for ground block) - Page 9 to Page - Page - Page - 9 IDC TEMINAL BLOCKS Page 0 - wire size : 0. to mm² ( to AWG) wire size : 0. to mm² ( to AWG) Page 0 wire size : 0.8 to. mm² ( to AWG) wire size : 0. to. mm² ( to AWG) Spacing : to 8 mm (.98" to.") :. to A body material : UL 9 V0 Beige body material : UL 9 V0 - IF for railway applications Spacing : to 8 mm (.98" to.") :. to A Spacing : to 8 mm (.98" to.") : 0 to 80 A/s Spacing : mm (.8") :. to 8 A body material : UL 9 V0 Beige body material : UL 9 V0 - IF for railway applications - PLUGGABLE IDC TEMINAL BLOCKS + PLUGS Beige body material : UL 9 V0 - IF for railway applications wire size : 0. to. mm² Spacing :. mm (.00") : to A body material : UL 9 V0 Page 0 to Page 9 to 00 Beige body material : UL 9 V0 - IF for railway applications wire size : 0.9 to. mm² Spacing :. mm (.00") : A body material : UL 9 V0 Low Products & Systems LV009 [SXU0009C00] - June 00 ABB Inc

8 Selection guide SENSO/ ACTUATO HEAVY DUTY SWITCH Page 0 to FUSE HOLDE Page to MINIBLOCKS Page SAFETY Page to 8 wire size : 0. to 0 mm² (0 to 0 AWG) Spacing : 8 mm (.") : A wire size : 0. to mm² ( to 0 AWG) Spacing : to 8 mm (.98" to.") : 0 to A wire size : 0. to mm² ( to 0 AWG) Spacing : to 8 mm (.98 to.") : to 0 A wire size : 0. to mm² ( to 0 AWG) Spacing : to 8 mm (.98" to.") :. to A (up to 00 A/ s. for ground blocks) Page 0 to Page to Page 9 to 9 wire size : 0. to mm² Spacing : mm (.98") Page 0 Page to :. A Page Pneumatic tool TOOLS wire size : 0. to, mm² ( to AWG) Spacing : to 8 mm (.98" to.") : 0 to A body material : UL 9 V0 Beige body material : UL 9 V0 - IF for railway applications TEST CONNECTOS wire size : 0. to. mm² ( to AWG) Spacing : to 8 mm (.98" to.") :. to 0 A ACCESSOIES Mounting rails P.Z Page 8 End stops wire size : 0. to mm² ( to AWG) Spacing : to 8 mm (.98" to.") :. to A Shield terminals for collector bar MAKING Page 9 to Extraction tool P0 P.G BADL BADH Vertical marking Horizontal marking Semi-automatic tool Simplified tool Page P P.Z P BAMH BAM Marking table Low Products & Systems ABB Inc LV009 [SXU0009C00] - June 00

9 Terminal blocks displacement - clamp DIN side side 0, - mm² 0, -, mm² - 8 AWG - AWG D,/. Spacing mm +0,0.98".".9".0" 8,.9" Color Part number Standard block D,/ Orange D,/ Blue D,/.N Black D,/ ed D,/ Ivory D,/ Yellow D,/ Green D,/ Standard mmblock 099. End stop th. 9 mm BADL V End stop th. 0 mm BAM V 00. End stop th. 0 mm BAM V0 V ail x, x P.Z ail x x, P ail x x, P Other end stops, rails and accessories : see section on accessories. 0,- mm² - AWG 0,-, mm² - AWG 0,- mm² -8 AWG 0,- mm² -8 AWG 000 V 8 kv 00 V, A A mm² 8 AWG Wire stripping ecommended ecommended length (screw) (screw) torque (screw) Protection 9, mm, mm 0,-0, Nm IP 0.".".-. lb.in NEMA Notes Standard block mm spacing. For multiple wires connections, the wires need to be of the same gauge and nature (solid or stranded). Terminal block body material is UL 9 V0. Part number End section grey blue yellow Circuit separator grey Test socket Test device Test plug Assembled jumper bar (without IP0 protection) Assembled jumper bar (with IP0 protection) 8 Jumper bar not assembled Post + screw + washer 0 Jumper bar less jumper bar to be inserted into jaw orange IP0 Comb-type jumper label Isolating cover Shield connector Hand tool kit Semi-automatic tool Pneumatic tool kit eplacement head kit 8 Extraction tool kit 9 Test connector FEDAD th. mm FEDAD th. mm FEDAD th. mm SCAD AL () DIA. mm DCB FC blue DIA. mm BJM () A BJM () A BJM () A BJM () A BJM () A 0 BJMI () A BJMI () A BJMI () A BJMI () A BJMI () A 0 BJS () A 0 EV BJE. 0 A BJE. 0 A BJE. 0 A BJE. 0 A BJE. 0 A BJE. 0 A BJE.8 0 A 8 BJE.9 0 A 9 BJE.0 0 A 0 BJB BJ., A BJ., A BJ., A BJ., A BJ.0, A 0 BJ.0, A 0 PC 0 A PC 0 A 0 EIP CBM th. 0, mm CBM8 th. 0,8 mm D CE. CEE See section on markers marking method C C 0 TM () SC and 00 V () rated voltage are required with these accessories. Low Products & Systems LV009 [SXU0009C00] - June 00 ABB Inc

10 Terminal blocks Displacement - clamp DIN side side 0, -, mm² 0, - mm² - AWG - 0 AWG Spacing mm +0,0.8" D /.... Color Part number Standard block Orange D / Blue D /.N Black D / ed D / Ivory D / Yellow D / Green D / End stop th. 9 mm BADL V End stop th. 0 mm BAM V 00. End stop th. 0 mm BAM V0 V ail x, x P.Z ail x x, P ail x x, P Other end stops, rails and accessories : see section on accessories. Wire stripping ecommended ecommended lenght (screw) screwdriver torque (screw) Protection 9, mm mm 0,-0,8 Nm IP 0.".".-. lb.in NEMA Notes UL CSA 0,- mm² -0 AWG -0 AWG 0,- mm² -0 AWG -0 AWG 0,-, mm² - AWG - AWG 0,-, mm² - AWG - AWG 000 V 00 V 00 V 8 kv, A 8 A 8 A, mm² 0/ AWG 0/ AWG Standard block mm. For multiple wire connections, the two wires need to be of the same gauge and nature (solid or stranded). Terminal block body material is UL 9 V0. Part numbers End section grey blue yellow Separator grey Test socket Test device Test plug Assembled jumper bar (without IP0 protection) Assembled jumper bar (with IP0 protection) 8 Jumper bar not assembled Post + screw + washer 9 less jumper bar orange IP0 0 Jumper bar less jumper bar to be inserted into jaw orange IP0 Pivoting jumper bar Jumper bar for alternated jumping Universal jumper bar Connector plate Comb type jumper bar Insulating tip Shield connector 8 Protection label for protection label 9 IDC jumper 0 Hand tool kit Semi-automatic tool Pneumatic tool kit eplacement head kit Extraction tool kit Test connector FEDAD FEDAD FEDAD th. mm th. mm th. mm SCAD AL AL DCJ FC FC () () DIA. mm DIA. mm yellow DIA. mm DIA. mm BJM BJM BJM BJM BJM BJMI BJMI BJMI BJMI BJMI BJS EV A A A A A A A A A A A BJE. BJE. BJE. BJE. BJE. BJE. BJE.8 BJE.9 BJE.0 BJB A A A A A A A A A BJ. BJ. BJ. BJ. BJ.0 BJ.0 BJP, A, A, A, A, A, A A 0 0 BJA A 0 BJDP BJDP BJDP EL () () () 0 A spa. <-> spa. 0 A spa. <-> spa. 0 A spa. <-> spa. 8 or 0 A PC PC PC PC EIP A A A A 0 CBM CBM8 EP th. 0, mm th. 0,8 mm blocks VSP AD, A D CE. CEE See section on markers marking method C C0 TM () A circuit separator SCAD and 00 V () rated voltage are required with these accessories. () See column on right page : "Various applications". 8 Low Products & Systems LV009 [SXU0009C00] - June 00 ABB Inc

11 D /..T D /.. D /.. D /.. D /..C Spacing mm +0,0.8" Spacing mm +0,0.8" Spacing mm +0,0.8" Spacing mm +0,0.8" Spacing mm +0,0.8" D /. equipped with DIA. mm test socket for test side screw D /. with partition D /.. equipped with DIA. mm test socket for test D /.. equipped with DIA. mm test socket for test D /.. equipped with DIA., mm flexible test socket for connector - () () () () () () Part numbers () () () () () () () () () () () () () () ()() ()() ()() () Part numbers Part numbers voltage: 800 V ( ) Part numbers voltage: 800 V ( ) Part numbers Various applications D /..C terminal blocks equipped with DIA., mm receive a connector. See catalog electrotechnic general (section 0). BJDP is used for the interconnection with terminal block series "M": spacing mm. BJDP is used for the interconnection with terminal block series "M": spacing mm. BJDP is used for the interconnection with terminal block series "D": spacing 8 mm. or terminal block series "M": spacing 8 or 0 mm. C C0 TM C C0 TM C C0 TM C C0 TM C C0 TM () A circuit separator SCAD and 00 V () rated voltage are required with these accessories. () See column on right: "Various applications". () Use of these accessories requires the user to cut out the partition. Low Products & Systems 9 ABB Inc LV009 [SXU0009C00] - June 00

12 Terminal blocks Displacement - clamp DIN side side -, mm² 0, - mm² - AWG - 8 AWG Spacing 8 mm +0,0." D /8.... Color Part number Standard block Orange D / Blue D /8.N Black D / ed D / Ivory D / Yellow D / Green D / End stop th. 9 mm BADL V End stop th. 0 mm BAM V 00. End stop th. 0 mm BAM V0 V ail x, x P.Z ail x x, P ail x x, P Other end stops, rails and accessories : see section on accessories. UL CSA 0,-0 mm² -8 AWG -8 AWG 0,- mm² -8 AWG -8 AWG -, mm² - AWG - AWG -, mm² - AWG - AWG 000 V 00 V 00 V 8 kv A A A, mm² 8/ AWG 8/ AWG Wire stripping ecommended ecommended lenght (screw) screwdriver torque (screw) Protection mm mm - mm 0,8- Nm IP 0."." -.".-8.9 lb.in NEMA Notes Standard block 8 mm. For multiple wire connections, the two wires need to be of the same gauge and nature (solid or stranded). Terminal block body material is UL 9 V0. Part numbers End section grey blue yellow Separator grey Test socket Test device Test plug Assembled jumper bar (without IP0 protection) Assembled jumper bar (with IP0 protection) 8 Jumper bar not assembled Post + screw + washer 9 less jumper bar orange IP0 0 Jumper bar Pivoting jumper bar Universal jumper bar Connector plate Comb type jumper bar Protection label for protection label IDC jumper Hand tool kit 8 Semi-automatic tool 9 Pneumatic tool kit 0 eplacement head kit Extraction tool kit Test connector FEDAD th. mm FEDAD th. mm FEDAD th. mm SCAD AL () DIA. mm AL () DIA. mm AL () DIA. mm DCO FC orange DIA. mm FC DIA. mm BJM8 A BJM8 A BJM8 A BJM8 A BJM8 A 0 BJMI8 A BJMI8 A BJMI8 A BJMI8 A BJMI8 A 0 BJS8 A 0 EV BJE8. A BJE8. A BJE8. A BJE8. A BJE8. A BJE8. A BJE8.8 A 8 BJE8.9 A 9 BJE8.0 A 0 BJB BJP8 0 A BJDP () 0 A spa.8 <-> spa. BJDP () 0 A spa.8 <-> spa. BJDP () 0 A spa.8 <-> spa.0 EL A PC8 0 A PC8 0 A PC8 0 A PC8 0 A 0 EP blocks EP8 blocks VSP AD, A D CE.8 CEE * Black marking for wire size -, mm² ( - AWG) See section on markers marking method TM C80 CAL8 () A separator SC and 00 V () rated voltage are required with these accessories () See column : "Various applications" 0 Low Products & Systems LV009 [SXU0009C00] - June 00 ABB Inc

13 D /8.. D /8.. D /8.. D /8..C Spacing 8 mm +0,0." Spacing 8 mm +0,0." Spacing 8 mm +0,0." Spacing 8 mm +0,0." D /8. with partition D /8.. equipped with DIA. mm test socket for test D /8.. equipped with DIA. mm test socket for test D /8.. equipped with DIA., mm flexible test socket for connector - () Part numbers Part numbers Part numbers Part numbers Part numbers Various applications () () () () () () () () () () () () ()() ()() ()() () D /8..C terminal blocks equiped with DIA., mm receive a connector described in the specific chapter. Universal jumper bar BJDP is used for the interconnection with terminal block series "M": spacing mm. BJDP is used for the interconnection with terminal block series "M": spacing mm. TM C80 CAL8 TM C80 CAL8 TM C80 CAL8 TM C80 CAL8 BJDP is used for the interconnection with terminal block series "M": spacing 0 mm. () See column : "Various applications". () Use of these accessories requires the user to cut out the partition. Low Products & Systems ABB Inc LV009 [SXU0009C00] - June 00

14 Terminal blocks Displacement - clamp DIN Spacing 8 mm +0,0." D /8. Color Part number Standard block D / Blue D /8.N Orange D / side side mm² 0, - mm² AWG - 8 AWG Standard 8 mm block 099. End stop th. 9 mm BADL V End stop th. 0 mm BAM V 00. End stop th. 0 mm BAM V0 V ail x, x P.Z ail x x, P ail x x, P Other end stops, rails and accessories : see section on accessories. 0,-0 mm² -8 AWG 0,- mm² -8 AWG mm² AWG mm² AWG 000 V 8 kv 00 V A A mm² 8/ AWG Wire stripping ecommended ecommended lenght (screw) screwdriver torque (screw) Protection mm mm - mm 0,8- Nm IP 0."." -.".-8.9 lb.in NEMA Notes Standard 8 mm block for connection of only one solid or stranded mm² wire. Part number End section grey blue Separator grey Test socket Test device Test plug Assembled jumper bar (without IP0 protection) Assembled jumper bar (with IP0 protection) 8 Jumper bar not assembled Post + screw + washer 9 less jumper bar orange IP0 0 Jumper bar Pivoting jumper bar Universal jumper bar Connector plate Comb type jumper bar Protection label for protection label IDC jumper Hand tool kit 8 Semi-automatic tool 9 eplacement head kit 0 Extraction tool kit FEDAD th. mm FEDAD th. mm SCAD AL () DIA. mm AL () DIA. mm AL () DIA. mm DCO FC () Orange DIA. mm FC () DIA. mm BJM8 () A BJM8 () A BJM8 () A BJM8 () A BJM8 () A 0 BJMI8 () A BJMI8 () A BJMI8 () A BJMI8 () A BJMI8 () A 0 BJS8 A 0 EV BJE8. A BJE8. A BJE8. A BJE8. A BJE8. A BJE8. A BJE8.8 A 8 BJE8.9 A 9 BJE8.0 A 0 BJB BJP8 ()() 0 A BJDP ()() 0 A spa. 8 <-> spa. BJDP ()() 0 A spa. 8 <-> spa. BJDP ()() 0 A spa. 8 <-> 0 spa. EL () A PC8 0 A PC8 0 A PC8 0 A PC8 0 A 0 EP blocks EP8 blocks VSP AD, A () BJDP is used for the interconnection with terminal block series "M" : spacing mm. BJDP is used for the interconnection with terminal block series "M" : spacing mm. BJDP is used for the interconnection with terminal block series "M" : spacing 0 mm. * White marking for wire size mm² ( AWG) See section on markers marking method TM C 80 CAL8 () A circuit separator SC is required and 00 V () rated voltage with these accessories. () Forbidden under explosive atmosphere EEX usage. () Only certified for "i" security. Low Products & Systems LV009 [SXU0009C00] - June 00 ABB Inc

15 Terminal block Displacement Double deck - clamp DIN side side 0, -, mm² 0, - mm² - AWG - 0 AWG Spacing mm + 0,0 (.8") D /.D. Color Part number Standard block D / Blue D /.N Orange D / Green D / Vertical jumper bar assembly (ITVE accessory ) Terminal block mm, double deck opened End stop th. mm BADH V End stop th. 9, mm BAMH V End stop th. 9, mm BAMH V0 V ail x, x P.Z ail x x, P ail x x, P Other end stops, rails and accessories : see section on accessories. UL CSA 0,- mm² -0 AWG -0 AWG 0,- mm² -0 AWG -0 AWG 0,8-, mm² - AWG - AWG 0,-, mm² - AWG - AWG 800 V 00 V 00 V kv, A 8 A 8 A, mm² 0/ AWG 0/ AWG Wire stripping ecommended ecommended lenght (screw) screwdriver torque (screw) Protection 9, mm mm 0,-0,8 Nm IP 0.".".-. lb.in. NEMA Notes Standard block mm. For multiple wires connections, the two wires need to be of the same gauge and nature (solid or stranded). Terminal block body material is UL 9 V0. Part numbers End section grey FEDAD V0 th. mm Separator grey SCAD Test socket AL () DIA. mm AL () DIA. mm Test device DCJ yellow Test plug FC DIA. mm Assembled jumper bar BJM () A (without IP0 protection) BJM () A BJM () A BJM () A BJM () A 0 Assembled jumper bar BJMI () A (with IP0 protection) BJMI () A BJMI () A BJMI () A BJMI () A 0 8 Jumper bar not assembled BJS () A 0 Post + screw + washer EV 9 less jumper bar BJE. A orange IP0 BJE. A 8 BJE. A BJE. A BJE. A BJE. A BJE.8 A 8 BJE.9 A 9 BJE.0 A 0 0 Jumper bar BJB less jumper bar BJ., A to be inserted into jaw BJ., A orange IP0 BJ., A BJ., A BJ.0, A 0 BJ.0, A 0 BJP () A BJA () A Pivoting jumper bar Jumper bar for alternated jumping Connector plate Comb type jumper bar Insulating tip Vertical jumper bar Shield connector 8 Protection label for protection label 9 IDC jumper 0 Hand tool kit Semi-automatic tool Pneumatic tool kit eplacement head kit Extraction tool kit Test connector EL A PC A PC A PC A PC A 0 EIP ITVE CBDS EP VSP AD, D CE. CEE A blocks The use of some accessories may decrease the block's voltage rating. For more information, consult us. See section on markers marking method TM C0 C () SC obligatory rated voltage with these accessories. Low Products & Systems ABB Inc LV009 [SXU0009C00] - June 00

16 Terminal blocks Displacement Double deck - clamp DIN side side 0, -, mm² 0, - mm² - AWG - 0 AWG D /.D.. Spacing mm + 0,0 (.8") Terminal block mm, double deck closed Colour Part numbers Vertical jumper bar assembly (ITVE accessory ) End stop th. mm BADH V End stop th. 9, mm BAMH V End stop th. 9, mm BAMH V0 V ail x, x P.Z ail x x, P ail x x, P Other end stops, rails and accessories : see section on accessories. UL CSA 0,- mm² -0 AWG -0 AWG 0,- mm² -0 AWG -0 AWG 0,8-, mm² - AWG - AWG 0,-, mm² - AWG - AWG 800 V 00 V 00 V kv, A 8 A 8 A, mm² 0/ AWG 0/ AWG Wire stripping ecommended ecommended lenght (screw) screwdriver torque (screw) Protection 9, mm mm 0,-0,8 Nm IP 0.".".-. lb.in. NEMA Notes Standard block mm double deck. For multiple wires connections, the two wires need to be of the same gauge and nature (solid or stranded). Terminal block body material is UL 9 V0. Part numbers End section grey Test socket Test device Test plug Assembled jumper bar (without IP0 protection) Assembled jumper bar (with IP0 protection) Jumper bar not assembled Post + screw + washer 8 less jumper bar orange IP0 9 Jumper bar 0 less jumper bar to be inserted into jaw orange IP0 Pivoting jumper bar Jumper bar for alternated jumping Connector plate Comb type jumper bar Insulating tip Vertical jumper bar Shield connector Protection label for protection label 8 IDC jumper 9 Hand tool kit 0 Semi-automatic tool Pneumatic tool kit eplacement head kit Extraction tool kit Test connector FEDAD V0 th.,0 mm AL () DIA.,0 mm AL () DIA.,0 mm DCJ yellow FC DIA.,0 mm BJM () A BJM () A BJM () A BJM () A BJM () A 0 BJMI () A BJMI () A BJMI () A BJMI () A BJMI () A 0 BJS () A 0 EV BJE. A BJE. A BJE. A BJE. A BJE. A BJE. A BJE.8 A 8 BJE.9 A 9 BJE.0 A 0 BJB BJ., A BJ., A BJ., A BJ., A BJ.0, A 0 BJ.0, A 0 BJP () A BJA () A 0 EL A PC A PC A PC A PC A 0 EIP ITVE CBDS EP VSP AD, D CE. CEE A blocks Some accessories can decrease the block's voltage rating. Consult us for more information. See section on markers marking method C0 C () Use of these accessories requires the user to cut out the partition. Low Products & Systems LV009 [SXU0009C00] - June 00 ABB Inc

17 Terminal block Displacement Double deck - clamp DIN side side -, mm² 0, - 0 mm² - AWG - 8 AWG Spacing 8 mm + 0,0 (.") D /8.D. Colour Part numbers Standard block Blue D /8.D.N Positionning of the vertical jumper bar (ITVE accessory ) Opened double deck terminal block 8 mm, End stop th. mm BADH V End stop th. 9, mm BAMH V End stop th. 9, mm BAMH V0 V ail x, x P.Z ail x x, P ail x x, P Other end stops, rails and accessories : see section on accessories. 0,-0 mm² 0,- mm² -, mm² -, mm² 800 V 8 kv A, mm² UL CSA Wire stripping ecommended ecommended lenght (screw) screwdriver torque (screw) Protection mm -,mm 0,8 - Nm IP 0."." -." lb.in. Notes Standard block 8 mm. For multiple wires connections, the two wires need to be of the same gauge and nature (solid or stranded). Terminal block body material is UL 9 V0. Part numbers End section grey FEDAD V0 th. mm 099. Test socket AL () DIA. mm 0 0. AL () DIA. mm 0.00 AL () DIA. mm 0 0. Test device DCO orange Test plug FC () DIA. mm FC () DIA. mm Assembled jumper bar BJM8 () A (without IP0 protection) BJM8 () A 08. BJM8 () A 08. BJM8 () A 08. BJM8 () A Assembled jumper bar BJMI8 () A 0 9. (with IP0 protection) BJMI8 () A 0 0. BJMI8 () A 0.00 BJMI8 () A 0.0 BJMI8 () A Jumper bar not assembled BJS8 A Post + screw + washer EV less jumper bar BJE8. A orange IP0 BJE8. A BJE8. BJE8. A A BJE8. A BJE8. A BJE8.8 A BJE8.9 A BJE8.0 A Jumper bar BJB Pivoting jumper bar BJP8 ()() 0 A Connector plate EL () A 0. Comb type jumper bar PC8 0 A 0. PC8 0 A 0.0 PC8 0 A 0.0 PC8 0 A Insulating tip EIP 0 0. Vertical jumper bar ITVE Protection label EP 0. EP for protection label VSP 0. IDC jumper AD, A Hand tool kit Semi-automatic tool 9 8 Pneumatic tool D 9 eplacement head kit Bridging plug BP8.A Test connector CE CEE The use of some accessories may decrease the block's voltage rating. For more information, consult us. See section on markers marking method TM C80 CAL8 () SC obligatory rated voltage with these accessories. () Forbidden under explosive atmosphere EEX usage. () Only certified for "i" security. Low Products & Systems ABB Inc LV009 [SXU0009C00] - June 00

18 Terminal block Displacement Double deck - clamp DIN side side -, mm² 0, - 0 mm² - AWG - 8 AWG Spacing 8 mm + 0,0 (.") D /8.D.. Colour Part numbers Positionning of the vertical jumper bar (ITVE accessory ) Double deck opened terminal block 8 mm End stop th. mm BADH V End stop th. 9, mm BAMH V End stop th. 9, mm BAMH V0 V ail x, x P.Z ail x x, P ail x x, P Other end stops, rails and accessories : see section on accessories. 0,-0 mm² 0,- mm² -, mm² -, mm² 800 V 8 kv A, mm² UL CSA Wire stripping ecommended ecommended lenght (screw) screwdriver torque (screw) Protection mm -,mm 0,8 - Nm IP 0."." -." lb.in. Notes Standard block 8 mm. For multiple wires connections, the two wires need to be of the same gauge and nature (solid or stranded). Terminal block body material is UL 9 V0. Part numbers End section grey FEDAD V0 th. mm 099. Test socket AL () DIA. mm 0 0. AL () DIA. mm 0.00 AL () DIA. mm 0 0. Test device DCO Test plug FC () DIA. mm FC () DIA. mm Assembled jumper bar BJM8 () A (without IP0 protection) BJM8 () A 08. BJM8 () A 08. BJM8 () A 08. BJM8 () A Assembled jumper bar BJMI8 () A 0 9. (with IP0 protection) BJMI8 () A 0 0. BJMI8 () A 0.00 BJMI8 () A 0.0 BJMI8 () A Jumper bar not assembled BJS8 A Post + screw + washer EV less jumper bar BJE8. A orange IP0 BJE8. A BJE8. BJE8. A A BJE8. A BJE8. A BJE8.8 A BJE8.9 A BJE8.0 A Jumper bar BJB Pivoting jumper bar BJP8 ()() 0 A Connector plate EL () A 0. Comb type jumper bar PC8 0 A 0. PC8 0 A 0.0 PC8 0 A 0.0 PC8 0 A Insulating tip EIP 0 0. Vertical jumper bar ITVE Protection label EP 0. EP for protection label VSP 0. IDC jumper AD, A Hand tool kit Semi-automatic tool 9 8 Pneumatic tool D 9 eplacement head kit Bridging plug BP8.A Test connector CE CEE The use of some accessories may decrease the block's voltage rating. For more information, consult us. See section on markers marking method TM C80 CAL8 () SC obligatory rated voltage with these accessories. () Forbidden under explosive atmosphere EEX usage. () Only certified for "i" security. Low Products & Systems LV009 [SXU0009C00] - June 00 ABB Inc

19 Compatibility of / clamp terminal blocks with clamp/ clamp switch terminal blocks for neutral circuits Standard / clamp terminal blocks with and 8 mm spacing are compatible with clamp/ clamp switch terminal blocks for neutral circuits. Wire connection and removal is possible with busbar in its place. / clamp terminal blocks for neutral circuits D,/.N. D /.N. Spacing mm + 0,0 (.98") Spacing mm + 0,0 (.8") D /8.N. D /.D.N. Spacing 8 mm + 0,0 (.") Spacing mm + 0,0 (.8") D /8.N. Spacing 8 mm + 0,0 (.") / clamp terminal blocks with blue body can be used for neutral connection. Blue color permits a good identification. wire size mm² wire size mm² wire size mm² wire size mm² wire size mm² D,/.N D /.N D /8.N D /.D.N D /8.N D /8.D.N. Spacing 8 mm + 0,0 (.") wire size mm² D /8.D.N and accessories of these blocks are described in standard / clamp block pages. Low Products & Systems ABB Inc LV009 [SXU0009C00] - June 00

20 Terminal blocks displacement Ground terminal blocks not electrically connected to the mounting rail - Compression-clamp DIN D,/.PI. Spacing mm " side side 0. - mm² 0. -, mm² - 8 AWG - AWG D /.PI. Spacing mm " side side 0. -, mm² 0. - mm² - AWG - AWG D /8.PI. Spacing 8 mm + 0,0." side side -. mm² 0. - mm² - AWG - 8 AWG and accessories, see clamp terminal blocks. * Black marking for wire side -, mm² (- AWG) P/N Yellow body / Green marking D,/.PI P/N P/N Yellow body / Green marking Yellow body / Green marking D/.PI D/8.PI current wire size Other characteristics Approvals End section grey 0,- mm² - AWG 0,-, mm² - AWG 0,- mm² -8 AWG 0,- mm² -8 AWG 0 A/ s. mm² 8 AWG Wire stripping ecommended ecommended Protection 9, mm, mm 0,-0, Nm IP0.".".-. lb.in NEMA FEDAD V0 th. mm UL 0,- mm² - AWG 0,- mm² - AWG 0,-, mm² - AWG 0,-, mm² - AWG 80 A/ s., mm² AWG CSA Wire stripping ecommended ecommended Protection 9, mm mm 0,-0,8 Nm IP0.".".-. lb.in NEMA UL CSA 0,-0 mm² -8 AWG 0,- mm² -8 AWG -8 AWG -, mm² - AWG - AWG -, mm² - AWG - AWG 00 A/ s., mm² AWG AWG Wire stripping ecommended ecommended Protection mm mm- mm 0,8- Nm IP0."." -.".-8.9 lb.in NEMA P/N P/N P/N FEDAD V0 th. mm FEDAD V0 th. mm See section on marking Marking method C C0 TM C C0 TM TM C80 CAL8 Terminal blocks displacement Ground terminal blocks not electrically connected to the mounting rail - Compression-clamp DIN D /8.PI. Spacing 8 mm " side side mm² / AWG 0. - mm² wire only - 8 AWG and accessories, see clamp terminal blocks. * White marking for wire size mm² ( AWG) P/N P.N P/N Yellow body / Green marking D/8.PI current wire size Other characteristics Approvals End section grey UL CSA 0,-0 mm² -8 AWG 0,- mm² -8 AWG -8 AWG mm² AWG AWG mm² AWG AWG 80 A/ s. mm² AWG AWG Wire stripping ecommended ecommended Protection mm mm- mm 0,8- Nm IP0."." -.".-8.9 lb.in NEMA FEDAD V0 th. mm P/N UL CSA Wire stripping ecommended ecommended Protection UL CSA Wire stripping ecommended ecommended Protection P/N P/N See section on marking Marking method TM C80 CAL8 8 Low Products & Systems LV009 [SXU0009C00] - June 00 ABB Inc

21 Terminal blocks displacement Ground terminal blocks electrically connected to the mounting rail - Compression-clamp DIN D,/.P. Spacing mm " side side 0. - mm² 0. -, mm² - 8 AWG - AWG D /.P. Spacing mm " side side mm² 0. - mm² - AWG - AWG D /8.P. Spacing 8 mm " side side -. mm² 0. - mm² - AWG - 8 AWG and accessories, see clamp terminal blocks. * Black marking for wire size -. mm² (- AWG) current wire size Other characteristics Approvals End section yellow grey P/N Green body / Yellow marking D,/.P D/.P D/8.P. 0,- mm² - AWG 0,-, mm² - AWG 0,- mm² -8 AWG 0,- mm² -8 AWG 0 A/ s. mm² 8 AWG Wire stripping ecommended ecommended Protection 9, mm, mm 0,-0, Nm IP0.".".-. lb.in NEMA UL CSA 0,- mm² -0 AWG -0 AWG 0,- mm² -0 AWG -0 AWG 0,-, mm² - AWG - AWG 0,-, mm² - AWG - AWG 80 A/ s., mm² AWG AWG Wire stripping ecommended ecommended Protection 9, mm mm 0,-0,8 Nm IP0.".".-. lb.in NEMA UL CSA 0,-0 mm² -8 AWG -8 AWG 0,- mm² -8 AWG -8 AWG -, mm² - AWG - AWG -, mm² - AWG - AWG 00 A/ s., mm² AWG AWG Wire stripping ecommended ecommended Protection mm mm- mm 0,8- Nm IP0."." -.".-8.9 lb.in NEMA P/N P/N P/N FEDAD V0 th. mm FEDAD V0 th. mm FEDAD V0 th. mm FEDAD V0 th. mm FEDAD V0 th. mm FEDAD V0 th. mm P/N Green body / Yellow marking P/N Green body / Yellow marking See section on marking Marking mode C C0 TM C C0 TM TM C80 CAL8 Terminal blocks displacement Ground terminal blocks electrically connected to the mounting rail - Compression-clamp DIN D /8.P. Spacing 8 mm " side side mm² / AWG 0. - mm² wire only - 8 AWG Double deck terminal blocks displacement Ground terminal blocks electrically connected to the mounting rail - Compression-clamp DIN D /.D.P. Spacing mm " side side mm² 0. - mm² - AWG - AWG 08,." 8,.8,9.99" and accessories, see clamp terminal blocks. * white marking for wire size.- mm² (- AWG) current wire size Other characteristics P/N Green body / Yellow marking D/8.P ,-0 mm² -8 AWG 0,- mm² -8 AWG mm² AWG mm² AWG 80 A/ s. mm² AWG Wire stripping ecommended ecommended Protection mm mm- mm 0,8- Nm IP0."." -.".-8.9 lb.in NEMA and accessories, see clamp terminal blocks. current wire size Other characteristics 0,- mm² 0,- mm² D /.D.P. UL,8. P/N Green body / Yellow marking CSA 0,8-, mm² 0,-, mm² 80 A/ s., mm² Wires tripping ecommended ecommended Protection 9, mm mm 0,-0,8 Nm.".".-. lb.in Approvals End section yellow grey P/N FEDAD V0 th. mm FEDAD V0 th. mm Approvals End section grey FEDAD V0 th. P/N mm 099. See section on markers Marking method TM C80 CAL8 See section on markers Marking method C C0 TM Low Products & Systems 9 ABB Inc LV009 [SXU0009C00] - June 00

22 displacement Heavy duty switch terminal blocks with blade clamp - DIN D,/.SN. Spacing mm +0,0.98" side side 0, - mm² 0, -, mm² -8 AWG - AWG D,/.SNT... Spacing mm +0,0.98" side side 0, - mm² 0, -, mm² -8 AWG - AWG End stop th. 9 mm BADL V End stop th. 0 mm BAM V 00. End stop th. 0 mm BAM V0 V ail x, x P.Z ail x x, P ail x x, P Other end stops, rails and accessories : see section on accessories. Notes For two wire connection max., the wires need to be of the same gauge and nature (solid or stranded). Terminal block body material is UL 9 V0. All switch terminal blocks offer a test point DIA. mm (or DIA.. mm on block D,/.SFAT.) on the side of the block. 8 End section grey orange Test plug Comb-type jumper Insulating tip Shield connector Hand tool kit Semi-automatic tool Pneumatic tool kit 8 eplacement head kit 9 Extraction tool kit 0 less jumper bar to be inserted into jaw orange IP0 Test connector Colour Part numbers Colour Part numbers With DIA. mm test on two sides. Orange D,/.SN. D,/.SN Orange D,/.SNT. D,/.SNT With DIA.. mm test on two sides. D,/.SNT * 0,- mm² - AWG 0,-, mm² - AWG 0,- mm² -8 AWG 0,- mm² -8 AWG 0 V 00 V kv 0 A mm² /8 AWG Wire stripping ecommended ecommended length (screw) screwdriver torque protection 9, mm, mm 0,-0, Nm IP 0.".".-. lb.in NEMA FEDAD th. mm FEDAD th. mm FC DIA. mm PC 0 A PC 0 A 0 EIP CBD th. 0,8 mm D BJ., A BJ., A BJ., A BJ., A BJ.0, A 0 BJ.0, A 0 CE. CEE * 0,- mm² - AWG 0,-, mm² - AWG 0,- mm² -8 AWG 0,- mm² -8 AWG 0 V 00 V kv 0 A mm² /8 AWG Wire stripping ecommended ecommended length (screw) screwdriver torque protection 9, mm, mm 0,-0, Nm IP 0.".".-. lb.in NEMA Part numbers FEDAD th. mm FEDAD th. mm FC DIA. mm 0.0 PC 0 A 0. PC 0 A EIP CBD th. 0,8 mm D BJ., A BJ., A BJ., A BJ., A BJ.0, A BJ.0, A CE. CEE Part numbers See section on markers marking method C C0 C C0 0 Low Products & Systems LV009 [SXU0009C00] - June 00 ABB Inc

23 Terminal blocks Displacement Heavy duty switch terminal blocks with blade clamp - DIN D /.SN. Spacing mm +0,0.8" side side 0, -, mm² 0, - mm² - AWG - 0 AWG D /.SNT... Spacing mm +0,0.8" side side 0, -, mm² 0, - mm² - AWG - 0 AWG End stop th. 9 mm BADL V End stop th. 0 mm BAM V 00. End stop th. 0 mm BAM V0 V ail x, x P.Z ail x x, P ail x x, P Other end stops, rails and accessories : see section on accessories. Notes Standard block mm. For multiple wire connections, the two wires need to be of the same gauge and nature (solid or stranded). Terminal block body material is UL 9 V0. All switch terminal blocks offer a test point (DIA. mm or DIA.. mm on block D /.SNT. ) on the side of the block. End section grey Test plug Comb-type jumper bar IDC jumper Shield connector Hand tool kit Semi-automatic tool 8 Pneumatic tool kit 9 eplacement head kit 0 Extraction head kit less jumper bar to be inserted into jaw orange IP0 Test connector Colour Part numbers Orange D /.SN. D /.SN. Wire stripping ecommended ecommended lenght (screw) screwdriver torque (screw) Protection 9, mm mm 0,-0,8 Nm IP 0.".".-. lb.in NEMA FEDAD th. mm FC DIA. mm PC A 0 AD, A CBD th. 0,8 mm D BJ., A BJ., A BJ., A BJ., A BJ.0, A 0 BJ.0, A 0 CE. CEE UL CSA 0,- mm² -0 AWG -0 AWG 0,- mm² -0 AWG -0 AWG 0,-, mm² - AWG - AWG 0,-, mm² - AWG - AWG 00 V 00 V 00 V kv 0 A 0 A 0 A, mm² 0/ AWG 0/ AWG Colour Part numbers With DIA. mm screw test socket for test on screw side. Orange With DIA.. mm screw test socket for test on screw side. D /.SNT UL CSA 0,- mm² -0 AWG -0 AWG 0,- mm² -0 AWG -0 AWG 0,-, mm² - AWG - AWG 0,-, mm² - AWG - AWG Section D /.SNT. D /.SNT. Wire stripping ecommended ecommended lenght (screw) screwdriver torque (screw) Protection 9, mm mm 0,-0,8 Nm IP 0 ".".-. lb.in NEMA Part numbers FEDAD th. mm FC DIA. mm 0. PC A AD, A 09.0 CBD th. 0,8 mm D BJ., A BJ., A BJ., A BJ., A BJ.0, A BJ.0, A CE CEE V 00 V 00 V kv 0 A 0 A 0 A, mm² 0/ AWG 0/ AWG Part numbers See section on markers Marking method C0 C C0 C Low Products & Systems ABB Inc LV009 [SXU0009C00] - June 00

24 Terminal blocks Displacement Heavy duty switch terminal blocks with blade - clamp DIN D /8.SN. Spacing 8 mm +0,0." side side -, mm² 0, - mm² - AWG - 0 AWG D /8.SNT... Spacing 8 mm +0,0." side side -, mm² 0, - mm² - AWG - 0 AWG End stop th. 9 mm BADL V End stop th. 0 mm BAM V 00. End stop th. 0 mm BAM V0 V ail x, x P.Z ail x x, P ail x x, P Other end stops, rails and accessories : see section on accessories. Notes Standard bloc 8 mm. For multiple wires connections, the two wires need to be of the same gauge and nature (solid or stranded). Terminal block body material is UL 9 V0. All switch terminal blocks offer a test point (DIA. mm or DIA. mm on block D /.SNT. ) on the side of the block. * Black marking for wire size -, mm² ( - AWG) End section grey Test plug Comb-type jumper bar IDC jumper Hand tool kit Semi automatic tool Pneumatic tool kit 8 eplacement head kit 9 Extraction tool kit 0 Test connector Colour Part numbers Colour Part numbers With DIA mm screw test socket for test on screw side. Orange D /8.SN. D /8.SN Orange D /8.SNT. D /8.SNT With DIA. mm screw test socket for test on screw side. D /8.SNT Wire stripping ecommended ecommended lenght (screw) screwdriver torque (screw) Protection 9, mm mm 0,-0,8 Nm IP 0.".".-. lb.in NEMA Part numbers FEDAD th. mm FC DIA. mm PC8 A 0 AD, A D CE.8 CEE UL CSA 0,- mm² -0 AWG -0 AWG 0,- mm² -0 AWG -0 AWG -, mm² - AWG - AWG -, mm² -AWG - AWG 00 V 00 V 00 V kv A A A, mm² 0/ AWG 0/ AWG A A A Section, mm² 0/ AWG 0/ AWG Wire stripping ecommended ecommended lenght (screw) screwdriver torque (screw) Protection 9, mm mm 0,-0,8 Nm IP 0.".".-. lb.in NEMA FEDAD th. mm FC DIA. mm PC8 A 0 AD, A D CE.8 CEE UL CSA 0,- mm² -0 AWG -0 AWG 0,- mm² -0 AWG -0 AWG -, mm² - AWG - AWG -, mm² - AWG - AWG 00 V 00 V 00 V kv Part numbers See section on markers Marking method C80 CAL8 C80 CAL8 Low Products & Systems LV009 [SXU0009C00] - June 00 ABB Inc

25 Selection guide for different types of plugs s of plugs s of fuses D,/.S. D,/.SFA... D /.S. D /8.S. Switching function Short-circuit plug BNC without test BNCT8 with test closed 8,." Plug open 9." Plug with solder tags and screws () Soldered fuses type FUBS - 0, to A - 0 V Flat fuses type FUPLV - to A - 0 V BNS.D BNSV BNSV Fuse protection function Fuse holder plug Automotive miniature fuses () type FUAUTO A to A - V maxi BFSAUTO V0 black BFAUTO V0 black Fuses x 0 Fuse holder plug type FU0-0, to A - 0 V Fuses x type FU -, to, A - 0 V BNF BNFD () BNFD() BNFL () BNF s of fuses Soldered fuses FUBS 0, A FUBS A FUBS A FUBS A FUBS A Flat fuses FUPLV A FUPLV A FUPLV A Fuses x 0 mm FU0 0, A FU0 A FU0 A FU0. A FU0 A Automotive miniature fuses FUAUTO A FUAUTO A Fuses x mm FU. A 0. FU A 0. FU. A FU A FU. A Nota : () Compatible with electronic components max.diameter or thickness for components : - plug BNSV : mm/." max. - plug BNSV8 : mm /."max. () For all fuses, the dissipated load should remain under 0,8 W. () with led V AC/DC. () with led 8 V AC/DC. () avec neon lamp 0-0 V AC/DC. Low Products & Systems ABB Inc LV009 [SXU0009C00] - June 00

26 Terminal blocks displacement Heavy duty switch blocks with plug clamp - DIN D,/.S. Spacing mm +0,0.98" side side 0, - mm² 0, -, mm² -8 AWG - AWG D /.S. Spacing mm +0,0.8" side side 0, -, mm² 0, - mm² - AWG - 0 AWG Switch connection block mm by polarized plug, delivered separately. Colour Part number Colour Part number End stop th. 9 mm BADL V End stop th. 0 mm BAM V 00. End stop th. 0 mm BAM V0 V ail x, x P.Z ail x x, P ail x x, P Other end stops, rails and accessories : see section on accessories. Notes mm and mm blocks. For multiple wire connections, the two wires need to be of the same gauge and nature (solid or stranded). Terminal block body material is UL 9 V0. * Black marking for wire size -, mm² ( - AWG) AC/DC End section grey orange Comb-type jumper bar Insulating tip IDC jumper Fuse-holder plug ivory Plug extractor Soldered fuses Short-circuit plug 8 Fuse-holder plug (for soldered fuses or flat fuses) 9 Fuse-holder plug (automotive) 0 Fuse-holder plug (for x0 or x fuses) () BNF with LED 8V AC/DC BNF with LED V AC/DC BNF with neon lamp 0-0V Shield connector Hand tool kit Semi-automatic tool Pneumatic tool kit eplacement head kit Extraction tool kit less jumper bar to be inserted into jaw orange IP0 8 Test connector See section on markers marking method D,/.S. 0,- mm² - AWG 0,-, mm² - AWG 0,- mm² -8 AWG 0,- mm² -8 AWG 0 V () 00 V () kv 0 A mm² Wire stripping ecommended ecommended length (screw) screwdriver torque (screw) Protection 9, mm, mm 0,-0, Nm IP 0.".".-. lb.in NEMA FEDAD th. mm FEDAD th. mm PC 0 A PC 0 A 0 EIP BNS.D EXBN FUBS FUBS FUBS FUBS FUBS th. mm 0, A A A A A CBD th. 0,8 mm D BJ., A BJ., A BJ., A BJ., A BJ.0, A 0 BJ.0, A 0 CE. CEE D /.S. UL CSA 0,-, mm² - AWG - AWG 0,-, mm² - AWG - AWG 0,- mm² -0 AWG -0 AWG 0,- mm² -0 AWG -0 AWG 00 V () 00 V () 00 V () kv 0 A 0 A A, mm² 0/ AWG 0/ AWG Wire stripping ecommended ecommended length (screw) screwdriver torque (screw) Protection 9, mm mm 0,-0,8 Nm IP 0.".".-. lb.in NEMA mm mm PC A 0 AD, EXBN BNC () BNSV () C C0 C0 C () Leakage current with LED V or 8 V : <, ma and with neon lamp 0 or 0 VAC/DC : < 0, ma. () See selection guide for dimensions of plugs and type of fuses to use. () Terminal block insulating voltage, working voltage according to fuse. Part numbers FEDAD FEDAD A mm mm BFAUTO V0 black BNFV0 V0 th. mm BNF D () V0 BNF D () V0 BNF L () V0 CBD D BJ., A BJ., A BJ., A BJ., A BJ.0, A 0 BJ.0, A 0 CE. CEE th. th. th. th. th. th. th. th. mm mm mm 0,8 mm Part numbers Low Products & Systems LV009 [SXU0009C00] - June 00 ABB Inc