Copper Meter Insetters

Transcription

1 Copper Meter Insetters To Set 5/8", 5/8" x 3/4", 3/4", & 1" Water Meters 1/1

2 Table of Contents Page Insetter Numbering System... 3 Meter Insetters 5/8", 5/8" x 3/4", 3/4", & 1" Series 740 "C" Style...45 Less end connections & union nuts... 5 Unions/Gaskets... 5 Series 741 "K" Style...69 Compression assemblies & ball valves... 7 & 9 Series 74 "H" Style Series 743 "M" Style Double Purpose x Double Purpose...1 Unions...13 Page Series 744 "PU" Style MNPT Thread x MNPT Thread...14 Series 745 "PZ" Style Left Offset...15 Series 746 "PZ" Style Right Offset...16 Series 747 "D" Style Model "A"...17 Series 748 "D" Style Model "B"...18 Series 749 "W" Style...19 A.Y. M c Donald Mfg. Co. is pleased to present its extensive line of copper meter insetters. These fine, high quality products offer the end user greater versatility due to the wide variety of end connections, heights, valve options, sizes, and special configurations. Versatility. That's the theme of our complete and flexible line of copper meter insetters. It also describes our system of model numbers. If you have requirements that are not contained in this catalog, please contact our customer service department at Our professional staff will be happy to work with you to select the product that will fit your needs. General Information All cast brass parts conform to latest revision of AWWA C800. Copper tubing has a 13/16" O.D. for 5/8", 5/8" x 3/4" or 3/4" meter setters and 1 1/8" O.D. for 1" meter setters. Solder is nolead. NSF rubber gaskets are furnished as standard. Contact factory for fiber or leather gaskets. All meter setters tested air under water at 85 PSIG. All meter swivel nuts have wire seal hole. Lockwing ball style meter valves are standard. All copper meter setters can be supplied with a test valve on the outlet tubing. For dual check backflow valves, see Single & Dual Check catalog section. Unless specified all components have meter nuts without saddles FAX sales@aymcdonald.com aymcdonald.com 11

3 Numbering System Model number 740 MF 33 means... Series 740MF 33 NoLead Copper Meter Insetter Series 740, 741, 74, 743, 744, 745, 746, 747, 748, 749 Meter Size 740 MF 33 Meter = 5/8"x3/4" Meter Meter 4 = 1" Meter Tube Height 740 MF 33 Not Applicable OUTLET INLET / Valve Configuration 740 MF 33 Not Applicable for 7401, 740, 7403, series only OUTLET OUTLET INLET INLET / End Connections 740 MF 33 IN OUT C = Copper Flare D = Double Purpose (Flare or FNPT) F = Female Union M = Male Union P = MNPT (No Coupling) Q = Q CTS Compression S = Solder Union / End Sizes 740 MF 33 IN OUT 1 = 1/" = 5/8" 4 = 1" T = T CTS Compression Z = 3Q PEP Compression = CTS MacPak Compression 3 = 33 PEP MacPak Compression 4 = 44 PVC MacPak Compression 5 = 55 IP MacPak Compression Not all end connections available on all styles of meter setters. Meter Dimensions 3/4" Short Meter, Meter Size 5/8" 5/8" x 3/4" 3/4" 3/4" x 1" 1" AMeter Threads 3/4" 1" 1" 1 1/4" 1 1/4" BLay Length 7 1/" 7 1/" 9" 9" 10 3/4" A.Y. M c Donald Spacing* 7 13/16" 7 13/16" 9 5/16" 9 5/16" 11 3/3" *Allows for meter and two gaskets FAX sales@aymcdonald.com aymcdonald.com 3

4 740 SERIES 5/8", 5/8" x 3/4" or 3/4" "C" Style The A.Y. McDonald 740 series C Style meter inside setting offers solderless construction with multiple options for vertical inlet and outlet union end connection configurations and combinations. Solderless Setting 740 To order "C" Style: Model No. 740FF 33 above means: = 5/8"x 3/4" = Standard (Blank) = Insetter less union and connections = Standard Tubes with Series Style Meter Size Meter Height and Valves Type of Connection Blank Space Size & and 740 "C" Style N = Insetter w/ nuts only No end pieces Sealing gaskets for union ends are 18G4. 1" Meter Settings The A.Y. McDonald series C Style meter inside setting offers multiple options for vertical inlet and outlet union end connection configurations and combinations with additional options for shut off or check valves. FF 33 1 = 1/" 4 = 1" C = Copper flare union (3/4" or 1") F = FNPT union (1/", 3/4" or 1") G = G CTS compression union (3/4" or 1") M = MNPT union (3/4" or 1") Q = Q CTS compression union (3/4") R = TE CTS compression union (3/4") S = Solder union (3/4" or 1") T = T CTS compression union (3/4" or 1") Y = H CTS compression union (3/4") = CTS MacPak compression union (3/4" or 1") 3 = 33 PEP MacPak compression union (3/4") 4 = 44 PVC MacPak compression union (3/4") 5 = 55 IP MacPak compression union (3/4") 740 N = Insetter w/ nuts only No end pieces To order "C" Style: Model No. 7404DD 44 above means: 4 = Standard (Blank) = Insetter less union and connections Series Style Meter Size Meter Height and Valves Type of Connection Blank Space Size & and = 1" = Standard Tubes with 4 = 1" "C" Style DD D = Double purpose union (1") M = MNPT union ( 1" & 1 1/4") S = Solder union (1") 44 Assemblies shipped with two meter gaskets and union gaskets. Insert stiffeners are required on all flexible plastic connections. Not all combinations available, contact factory with your requirements. Most Meter Setters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements FAX sales@aymcdonald.com aymcdonald.com 11

5 Less End Connections and Union Nuts The A.Y. McDonald 740 series C Style meter inside setting is also available less end connections or less end connections and union nuts. These parts can be purchased separately to configure as required. Less Nut/Union Less Union 740 SERIES Solderless Setting Solderless Setting Soldered Tubes Model Number Example 40 1, 5/8" meter 40, 5/8" x 3/4" meter 40 3, 3/4" meter Model Number Example 40N1, 5/8" meter 40N, 5/8" x 3/4" meter 40N3, 3/4" meter Model Number Example 740N4, 1" meter, Less union 7404, Less nut/union Unions Unions for 5/8", 5/8" x 3/4", 3/4", & 1" Meter Settings "C" Style Unions Model description 5/8", 5/8" x 3/4", 3/4" Meters 740C3 3/4" Flare union 740C4 1" Flare Union with swivel nut 740F1 1/" FNPT union 740F3 1" FNPT union 740F4 1" FNPT union with swivel nut 740M3 3/4" MNPT union 740M4 1" MNPT union 740S3 3/4" Solder union 740S4 1" Solder union 740T3 3/4" T CTS Comp union 740T4 1" T CTS Comp union with swivel nut /4" CTS Comp union Model description /4" 33 PEP Comp union with swivel Nut /4" 44 PVC Comp union with swivel Nut /4" 55 IP Comp union with swivel nut 40N 3/4" Union nut only 1" Meters 404N 1" Union nut 7404D4 1" Double purpose union 7404M4 1" MNPT union 7404M " MNPT union 7404S4 1" Solder union 7404M " MNPT union " CTS Comp union with swivel nut 740Q3 3/4" Q CTS Comp. union EPDM Meter Gaskets 18G1 5/8" Meter gaskets 18G 5/8" x 3/4" Meter gaskets 18G3 3/4" Meter gaskets 18G4 1" Meter gaskets 0G4 1" Union gasket Assemblies shipped with two meter gaskets. Insert stiffeners are required on all flexible plastic connections. Not all combinations available, contact factory with your requirements. Most Meter Setters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements FAX sales@aymcdonald.com aymcdonald.com 5

6 741 SERIES 5/8", 5/8" x 3/4" or 3/4" Meter Settings "K" Style The A.Y. McDonald 741 series K Style meter inside setting offers left and right offset configurations along with additional options for shut off or check valves. Minimal changes to customer plumbing is required. Cut in style end connections are available to connect to varying service line materials (see page 9). The special inlet and outlet thread and oring seal combination offers quick, leak free connections. Series 741Standard "K" Style thread S Oring 741QF Series 741 with Angle Ball Valve and Angle Dual Check Valve 741 To order "K" Style: Model No. 741 above means: QF Series Style Meter Size Meter Height and Valves 741 "K" Style = Standard (Left) C = K Style insetter with 744 series tubes, see page 13. D = 7/8" tube (Not available for 5/8" meters with flange) X = K Style with right hand configuration (with valves only) = 5/8"x 3/4" = Standard (If Blank) = Standard settings less valve and end connections = Standard Tubes with N = No valve meter nut (Blank) = Standard settings less valve and end connections Assemblies shipped with two meter gaskets. 41S Oring available 5 per bag (sold in bags only). Valves and compression assemblies ordered separately, see page 7. Inline Dual Check Backflow Valves available for 5/8", 5/8" x 3/4", and 3/4" "K" style insetters, see page 7. Contact factory for setting the test valve soldered in tubing. Not all combinations available, contact factory with your requirements. Most Meter Setters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements FAX sales@aymcdonald.com aymcdonald.com 11

7 Ball Valves for K Style MODEL VALVE SIZE DESCRIPTION S 3/4" x 5/8" x 3/4" K Swivel Nut x K Male Thread SD 3/4" x 5/8" x 3/4" K Swivel Nut x K Male Thread with test port/drain SW 3/4" x 5/8" x 3/4" K Swivel Nut x K Male Thread with lockwing 41S Oring available5 per bag (sold in bags only) 41SKBV Oring available5 per bag (sold in bags only) /4" FNPT x K Thread Female /4" x 5/8" x 3/4" FNPT x K Thread SD 3/4" x 5/8" x 3/4" FNPT x K Thread Stop & Drain W 3/4" x 5/8" x 3/4" FNPT x K Thread W 3/4" FNPT x K Thread 76101W 3/4" x 5/8" x 3/4" Flare x K Thread 76101W 3/4" Flare x K Thread 76101W 1" x 3/4" x 3/4" Flare x K Thread 76101WT 3/4" x 5/8" x 3/4" T CTS compression x K Thread 76101WT 3/4" T CTS compression x K Thread 76101WT 1" x 3/4" x 3/4" T CTS compression x K Thread 76101W 3/4" x 5/8" x 3/4" CTS compression x K Thread 76101W 3/4" CTS compression x K Thread 76101W 1" x 3/4" x 3/4" CTS compression x K Thread 76101W33 3/4" 33 PEP compression x K Thread 76101W44 3/4" 44 PVC compression x K Thread 76101W55 3/4" 55 IP compression x K Thread 41S oring W S 41SKBV oring 741 SERIES 76101W 76101WT 76101W 76101W W T , Fittings for Model 7411, 741, or 7413 MODEL SIZE DESCRIPTION P 3/4" MNPT x K Thread S 1/" x 3/4" Solder x K Thread S 3/4" Solder x K Thread /4" CTS compression x K Thread /" x 3/4" CTS compressionx K Thread " x 3/4" CTS compression x K Thread /4" x 3/4" CTS compression x K Thread /16" x 3/4" CTS compression x K Thread Q 3/4" Q CTS compression x K Thread T 3/4" T CTScompression x K Thread T 1" x 3/4" T CTS compression x K Thread MODEL SIZE DESCRIPTION T 1 1/4" x 3/4" T CTS compression x K Thread /4" 33 PEP compression x K Thread " x 3/4" 33 PEP compression x K Thread Q 1" x 3/4" 3Q PEP compression x K Thread /" x 3/4" 44 PVC compression x K Thread /4" 44 PVC compression x K Thread " x 3/4" 44 PVCcompression x K Thread /4" 55 IP compression x K Thread " x 3/4" 55 IP compression x K Thread 47541GSKT Copper spacing gasket 711 Series Inline Dual Check Backflow Preventers "K" Thread MODEL SIZE 7113KL 33 Male K integral Female K union 3/4" x 3/4" 7113LK 33 Female K union Male K integral 3/4" x 3/4" 7113LT 33 Female K union T CTS compression integral 3/4" x 3/4" 7113L 33 Female K union CTS compression integral 3/4" x 3/4" 7113LE 33 Female K union FNPT integral 3/4" x 3/4" For Handyloc Replace "Q" or "3Q" with "H" or "3H" in 3/4" & 1" only. Dual check will also screw directly to our series 741, 745, 746, 747, and 748 insetters, Insert stiffeners are required on all flexible plastic connections FAX sales@aymcdonald.com aymcdonald.com 7

8 741 SERIES 1" Meter "K" Style The A.Y. McDonald series K Style meter inside setting offers left and right offset configurations along with additional options for shut off or check valves. End connections are available to connect to varying service line materials (see page 11). The Male Iron Pipe Thread (MNPT) inlet and outlet thread allows multiple combinations with female adapters for quick, leak free connections. To order "K" Style: Model No means: /4" MNPT Series Style Meter Size 741 "K" Style = Standard (Left) C = K Style insetter with 744 series tubes, see page = 1" (1 1/4" MNPT In/Out) Meter Settings w/integral Valves Series 741 with Angle Ball Valve and Angle Dual Check Valve 741 To order "K" Style: Model No. 7414QF above means: C = K Style insetter with 744 series tubes, see page 13. X = K Style or 744 style with right hand configuration, see page = 1" (1 1/4" MNPT In/Out) = Standard (Blank) = Standard settings less valve and end connections QF Series Style Meter Size Meter Height and Valves 741 "K" Style Assemblies shipped with two meter gaskets. Valves and compression assemblies ordered separately, see page 9. Contact factory for setting the test valve soldered in tubing. Not all combinations available, contact factory with your requirements. Most Meter Setters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements. = Standard Tubes with N = No valve meter nut (Blank) = Standard settings less valve and end connections FAX sales@aymcdonald.com aymcdonald.com 11

9 741 SERIES Compression Assemblies & Ball Valves for 1" "K" Style Ball Valves for Model 7414 MODEL SIZE DESCRIPTION 76101MW 1" x 3/4" x 1" Swivel x FNPT 76101MW 1" Swivel x FNPT 76100MW 1" x 3/4" x 1" Swivel x Flare 76100MW 1" Swivel x Flare 76100MWQ 1" x 3/4" x 1" Swivel x Q CTS compression 76100MWQ 1" Swivel x Q CTS compression 76100MWT 1" x 3/4" x 1" Swivel x T CTS compression 76100MWT 1" Swivel x T CTS compression 76100MW 1" x 3/4" x 1" Swivel x CTS compression 76100MW 1" Swivel x CTS compression 76101MW 76100MWT 76100MW, 76100MW MW44 Fittings for Model 7414 MODEL SIZE DESCRIPTION " x 1 1/4" Flare x FNPT " x 1 1/4" CTS compression x FNPT /" x 1 1/4" CTS compression x FNPT 74754G 1 1/4" G CTS compression x FNPT 74754T 1" x 1 1/4" T CTS compression x FNPT 74754T 1 1/4" T CTS compression x FNPT /4" CTS compression x FNPT /4" 33 PEP compression x FNPT " x 1 1/4" 33 PEP compression x FNPT G 1" x 1 1/4" 3G PEP compression x FNPT Q 1" x 1 1/4" 3Q PEP compression x FNPT " x 1 1/4" 44 PVC compression x FNPT /4" 44 PVC compression x FNPT /" x 1 1/4" 44 PVC compression x FNPT " x 1 1/4" 55 IP compression x FNPT /" x 1 1/4" 55 IP compression x FNPT " x 1 1/4" CTS Less internal pipe stop G 1" x 1 1/4" G CTS Less internal pipe stop Q 1" x 1 1/4" Q CTS Less internal pipe stop T 1" x 1 1/4" T CTS Less internal pipe stop 74754T , Series Inline Dual Check Backflow Preventers "K" Thread MODEL SIZE 7114JF 54 Meter Swivel Nut FNPT 1 1/4" x 1" 7114JM 54 Meter Swivel Nut MNPT 1 1/4" x 1" 7114JM 54 For Handyloc Replace "Q" or "3Q" with "H" or "3H" in 1" only. For more information on our full line of backflow preventers, refer to Single & Dual Check section. Dual check will also screw directly to our series 741, 745, 746, 747, and 748 insetters FAX sales@aymcdonald.com aymcdonald.com 9

10 74 SERIES 5/8", 5/8" x 3/4", or 3/4" "H" Style, Less Valves The A.Y. McDonald 74 series H Style meter inside setting offers integral compression type inlet and outlet end connection configurations with additional options for shut off or check valves. 74 5/8", 5/8" x 3/4", or 3/4" Meter Settings w/ Valves "H" Style To order "H" Style: Model No above means: Series Style Meter Size Meter Height and Valves Type of Connection Blank Space Size & and 74 = Standard = Standard Tubes with 1 = 1/" "H" Style = 5/8" x 3/4" D = 7/8" tube (Not available for 5/8" meters with flange) 33 G = G CTS compression integral (3/4") H = H CTS Handyloc compression integral (3/4") J = Kitec compression integral (3/4") Q = Q CTS McQuick compression integral (3/4") T = T CTS compression integral (3/4") = CTS MacPak compression integral (1/", 3/4") 3 = 33 PEP MacPak compression integral (3/4") 4 = 44 PVC MacPak compression integral (3/4") 5 = 55 IP MacPak compression integral (3/4") 74 To order "H" Style: Model No. 74QFQQ 33 above means: = 5/8"x 3/4" QF = Standard Tubes with N = No valve (Blank) = Standard settings less valve and end connections Series Style Meter Size Meter Height and Valves Type of Connection Blank Space Size & and 74 = Standard 1 = 1/" "H" Style QQ Assemblies shipped with two meter gaskets. Insert stiffeners are required on all flexible plastic connections. Not all combinations available, contact factory with your requirements. Most Meter Setters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements. 33 G = G CTS compression integral (3/4") H = H CTS Handyloc compression integral (3/4") J = Kitec compression integral (3/4") Q = Q CTS McQuick compression integral (3/4") T = T CTS compression integral (3/4") = CTS MacPak compression integral (1/", 3/4") 3 = 33 PEP MacPak compression integral (3/4") 4 = 44 PVC MacPak compression integral (3/4") 5 = 55 IP MacPak compression integral (3/4") FAX sales@aymcdonald.com aymcdonald.com 11

11 74 To order "H" Style: Model No above means: 4 Series Style Meter Size Meter Height and Valves Type of Connection Blank Space Size & and 74 4 = 1" = Standard = Standard Tubes with 4 = 1" "H" Style 74 SERIES 1" "H" Style, Less Valves The A.Y. McDonald 74 series H Style meter inside setting offers integral compression type inlet and outlet end connection configurations with additional options for shut off or check valves. 44 G = G CTS compression integral (1") H = H CTS Handyloc compression integral (1") Q = Q CTS McQuick compression integral (1") T = T CTS compression integral (1") = CTS MacPak compression integral (1") 1" Meter Settings w/ Valves "H" Style 74 To order "H" Style: Model No. 744QFQQ 44 above means: 4 QF = Standard Tubes with N = No valve (Blank) = Standard settings less valve and end connections Series Style Meter Size Meter Height and Valves Type of Connection Blank Space Size & and 74 4 = 1" = Standard 4 = 1" "H" Style QQ Assemblies shipped with two meter gaskets. Insert stiffeners are required on all flexible plastic connections. Not all combinations available, contact factory with your requirements. Most Meter Setters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements. 44 G = G CTS compression integral (1") H = H CTS Handyloc compression integral (1") Q = Q CTS McQuick compression integral (1") T = T CTS compression integral (1") = CTS MacPak compression integral (1") FAX sales@aymcdonald.com aymcdonald.com 11

12 743 SERIES 5/8", 5/8" x 3/4" or 3/4" "M" Style Double Purpose x Double Purpose The A.Y. McDonald 743 series M Style meter inside setting offers inlet and outlet union end connection configurations with additional options for shut off or check valves. To order "M" Style: Model No. 743DD 33 means: 743 D = 7/8" tube (Not available for 5/8" meters with flange) N = Insetter w/ Nuts Only No End pieces = 5/8"x 3/4" = Standard Tubes with N = No valve (Blank) = Standard settings less valve and end connections Series Style Meter Size Meter Height and Valves Type of Connection Blank Space Size & and 743 "M" Style 33 = Standard 1 = 1/" (Blank) = Insetter less 4 = 1" union and connections D = Double purpose union (Flare or FNPT) (3/4") F = FNPT union (1/" or 1") L = Less nut or connection & nut M = MNPT union (3/4", 1", or 1 1 4") S = Solder union (3/4" or 1") T = T CTS compression union (3/4", 1") = CTS MacPak compression union (3/4" or 1") 3 = 33 PEP MacPak compression union (3/4") 4 = 44 PVC MacPak compression union (3/4") 5 = 55 IP MacPak compression union (3/4") 1" Meter Settings 743 N = Insetter w/ nuts only no end pieces To order "M" Style: Model No. 7434DD 44 above means: 4 4 = 1" = Standard (Blank) = Insetter less union and = Standard Tubes with N = No valve Series Style Meter Size Meter Height and Valves Type of Connection Blank Space Size & and 743 "M" Style 4 = 1" DD 44 connections D = Double purpose union (Flare or FNPT) (1") L = Less nut or connection & nut M = MNPT Union (1" & 1 1 4") S = Solder Union (1") Assemblies shipped with two meter gaskets. Insert stiffeners are required on all flexible plastic connections. Not all combinations available, contact factory with your requirements. Most Meter Setters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements FAX sales@aymcdonald.com aymcdonald.com 11

13 Model description Unions 5/8", 5/8" x 3/4", 3/4", or 1" "M" Style Double Purpose x Double Purpose Model description 70C3 3/4" Flare union 704 1" CTS Comp union with union Nut 70C4 1" Flare union with union nut 70F1 1/" FNPT union 70Q3ASY Model 3/4" Q CTS Compression with union nut descript 70F4 1" FNPT union with union nut 70D3 3/4" Double Purpose union Flare or FNPT 70M3 3/4" MNPT union /4" 33 PEP Comp union with union nut /4" 44 PVC Comp union with union nut /4" 55 IP Comp union with union nut 40N 3/4" Union nut only 70M4 1" MNPT union 0G3 3/4" Double Purpose Gasket 70S3 3/4" Solder union 70J3 3/4" C903* Comp union 70G3 3/4" G CTS Comp union 70S4 1" Solder union 70Q3 3/4" Q CTS Comp union 1" Meters 404N 1" Union nut 70T3 3/4" T CTS Comp union 7404D4 1" Double purpose union flare or FNPT 70T4 1" T CTS Comp union with union nut 70Z3 3/4" 3Q PEP Comp union with union nut escription 7404M4 1" MNPT union 7404M5 1 1/4" MNPT union 7404S4 1" Solder union 40G4 1" Double purpose gaskets 703 3/4" CTS Comp union Insert stiffeners are required on all flexible plastic connections. Note: Insetters normally supplied with end connections. The table above is for ordering replacement couplings FAX sales@aymcdonald.com aymcdonald.com 13

14 744 SERIES 5/8", 5/8" x 3/4", 3/4", or 1" "PU" Style Less Valves MNPT Thread x MNPT Thread The A.Y. McDonald 744 series PU Style meter inside setting offers integral Male Iron Pipe Thread inlet and outlet end connection configurations with additional options for shut off or check valves. To order "PU" Style: Model No. 744 means: 744 Series Style Meter Size 744 Q = PU style setter = 5/8" x 3/4" w/k style tubes, see page 6. 4 = 1" X = PU style setter w/k style tube in right hand configuration, see page 6. Meter Settings w/integral Valves Series 744 with Angle Ball Valve and Angle Dual Check Valve 744 To order "PU" Style: Model No. 744QF above means: QF Series Style Meter Size Meter Height and Valves 744 Q = PU style setter w/k style tubes, see page 6. X = PU style setter w/k style tube in right hand configuration, see page 6. = 5/8" x 3/4" 4 = 1" = Standard (Blank) = No attached valves = Standard Tubes with N = No valve Assemblies shipped with two meter gaskets. / Options: MNPT Thread x MNPT Thread. Not all combinations available, contact factory with your requirements. Most Meter Setters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements FAX sales@aymcdonald.com aymcdonald.com 11

15 745 SERIES 5/8", 5/8" x 3/4", 3/4", or 1" "PZ" Style Left Offset Less Valves The A.Y. McDonald 745 series PZ Style meter inside setting offers left offset configuration for confined space installations along with additional options for shut off or check valves. Cut in style end connections are available to connect to varying service line materials (see page 7 & 9). The special inlet and outlet thread and oring seal combination offers quick, leak free connections. To order "PZ" Style: Model No. 745 above means: 745 Series Style Meter Size 745 D = 7/8" tube (Not available for 5/8" meters with flange) = 5/8" x 3/4" 4 = 1" (1 1/4" MNPT In/Out) SERIES 745 LEFT "K" Style thread 41S Oring Meter Settings w/integral Valves SERIES 745 LEFT 745 To order "PZ" Style: Model No. 745QF above means: D = 7/8" tube (Not available for 5/8" meters with flange) = 5/8" x 3/4" 4 = 1" (1 1/4" MNPT In/Out) = Standard (Blank) = No height QF Assemblies shipped with two meter gaskets. Valves and compression assemblies ordered separately, see pages 7 and 9. Inline dual check backflow valves available for 5/8", 5/8" x 3/4" and 3/4" "PZ" style insetters, see page 7. Not all combinations available, contact factory with your requirements. Most Meter Setters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements. Series Style Meter Size Meter Height and Valves 745 = Standard Tubes with N = No valve (Blank) = No attached valves FAX sales@aymcdonald.com aymcdonald.com 15

16 746 SERIES 5/8", 5/8" x 3/4", 3/4", or 1" "PZ" Style Right Offset Less Valves The A.Y. McDonald 746 series PZ Style meter inside setting offers right offset configuration for confined space installations along with additional options for shut off or check valves. Cut in style end connections are available to connect to varying service line materials (see page 7 & 9). The special inlet and outlet thread and oring seal combination offers quick, leak free connections. To order "PZ" Style: Model No. 746 above means: SERIES 746 RIGHT 746 Series Style Meter Size Oring "K" Style thread 746 D = 7/8" tube (Not available for 5/8" meters with flange) = 5/8" x 3/4" 4 = 1" (1 1/4" MNPT In/Out) Meter Settings w/integral Valves SERIES 746 RIGHT 746 To order "PZ" Style: Model No. 746QF above means: D = 7/8" tube (Not available for 5/8" meters with flange) = 5/8" x 3/4" 4 = 1" (1 1/4" MNPT In/Out) = Standard (Blank) = No height QF Assemblies shipped with two meter gaskets. Valves and compression assemblies ordered separately, see pages 7 and 9. Inline dual check backflow valves available for 5/8", 5/8" x 3/4" and 3/4" "PZ" style insetters, see page 7. Not all combinations available, contact factory with your requirements. Most Meter Setters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements. Series Style Meter Size Meter Height and Valves 746 = Standard Tubes with N = No valve (Blank) = No attached valves FAX sales@aymcdonald.com aymcdonald.com 11

17 747 SERIES 5/8", 5/8" x 3/4", 3/4", or 1" "D" Style The A.Y. McDonald 747 series D Style meter inside setting aligns meter with piping in water lines that are near the ceiling with additional options for adding shut off or check valves. Cut in style end connections are available to connect to varying service line materials (see page 7 & 9). The special inlet and outlet thread and oring seal combination offers quick, leak free connections 5/8", 5/8" x 3/4" or 3/4" only. 41S Oring "K" Style thread With Angle Ball Valve and Angle Dual Check Valve SERIES 747 MODEL A Model Number Example SERIES 747 MODEL A Model Number Example 747 4QF 747 To order "D" Style: Model No. 7474QF means: 4 QF Series Style Meter Size Meter Drop and Valves 747 = 5/8" x 3/4" 4 = 1" (1 1/4" MNPT In/Out) N = No valve (Blank) = Less valves Assemblies shipped with two meter gaskets. Valves and compression assemblies ordered separately, see pages 7 and 9. For angle ball valves and/or angle dual check valves integral to the insetter, contact factory. Inline dual check backflow valves available for 5/8", 5/8" x 3/4" and 3/4" "D" style insetters, see page 7. Not all combinations available, contact factory with your requirements. Most Meter Setters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements FAX sales@aymcdonald.com aymcdonald.com 17

18 748 SERIES 5/8", 5/8" x 3/4", 3/4", or 1" "D" Style The A.Y. McDonald 748 series D Style meter inside setting sets meter at a right angle to the piping in water lines that are near the ceiling with additional options for adding shut off or check valves. Cut in style end connections are available to connect to varying service line materials (see page 7 & 9). The special inlet and outlet thread and oring seal combination offers quick, leak free connections 5/8", 5/8" x 3/4" or 3/4" only.. 41S Oring "K" Style thread SERIES 748 MODEL A Model Number Example SERIES 748 MODEL A Model Number Example 748 4QF 748 To order "D" Style: Model No. 7484QF means: 4 QF Series Style Meter Size Meter Drop and Valves 748 = 5/8" x 3/4" 4 = 1" (1 1/4" MNPT In/Out) N = No valve (Blank) = Less valves Assemblies shipped with two meter gaskets. Valves and compression assemblies ordered separately, see pages 7 and 9. For angle ball valves and/or angle dual check valves integral to the insetter, contact factory. Inline dual check backflow valves available for 5/8", 5/8" x 3/4" and 3/4" "D" style insetters, see page 7. Not all combinations available, contact factory with your requirements. Most Meter Setters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements FAX sales@aymcdonald.com aymcdonald.com 11

19 749 SERIES 5/8", 5/8" x 3/4" or 3/4" "W" Style The A.Y. McDonald 749 series W Style meter inside tandem setting offers integral Male Iron Pipe Thread inlet and outlet end connections that accept a variety of female couplings or valves with additional options for shut off or check valves plumbed into the tubing to accept inline, a meter and a pressure regulating device. Please supply device length and end connection configuration when ordering. Model Number Example /4 Model Number Example 749 QF x = Standard D = 7/8" tube (Not available for 5/8" meters with flange) N = Insetter w/ nuts only no end pieces To order "W" Style: Model No /4 means: = 5/8" x 3/4" Blank = Standard = w/integral valves = Standard Tubes with N = No valve 17 3/4 Series Style Meter Size Blank Space and Valves Blank Space Spread Between Flanges 749 "W" Style Model Meter Size SPREAD DEVICE LENGTH /8" 17 3/4" 6 1 4" 749 5/8" x 3/4" 17 3/4" 6 1 4" /4" 19 1/4" 6 1 4" Assemblies shipped with three meter gaskets. For setting meter and FNPT x FNPT device. Includes and 7460 adapters. Other spreads available, contact factory. Not all combinations available, contact factory with your requirements. Most Meter Setters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements FAX sales@aymcdonald.com aymcdonald.com 19

20 A.Y. McDonald Mfg. Co. is a leading manufacturer of Waterworks Brass, Plumbing Valves, Pumps and Water Systems, and High Pressure Gas Valves and Meter Bars. The Company has distinguished itself with a proud tradition of quality and reliability since its founding in The mission of A.Y. McDonald Mfg. Co., in the words of our founder, is to make good products and sell them honestly. We, the stockholders and employees, accomplish this by extending the McDonald family culture through excellent customer service and by focusing on our customers needs. WARNING: It is unlawful in CALIFORNIA & VERMONT (effective 1/1/010); MARYLAND (effective 1/1/01); LOUISIANA (effective 1/1/013) and the UNITED STATES OF AMERICA (effective 1/4/014) to use any product in the installation or repair of any public water system or any plumbing in a facility or system that provides water for human consumption if the wetted surface area of the product has a weighted average lead content greater than 0.5%. This prohibition does not extend to service saddles used in California, Louisiana or under USA Public Law /1 More than a brand. We re a family. aymcdonald.com sales@aymcdonald.com